Search Results

Search found 17749 results on 710 pages for 'connection pool'.

Page 133/710 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

• Wireless will not connect

  - by azz0r

  Hello, I have installed Ubuntu 10.10 on the same machine as my windows setup. However, it will not connect to my wireless network. It can see its there, it can attempt to connect, yet it will never connect. It will keep bringing up the password prompt everyso often. I have tried turning my security to WEP, I ended up turning it back to WPA2. It is set to AES (noted a few threads on google about that). Can you assist? I would love to dive into Ubuntu, but without the internet its pointless. --- lshw -C network --- *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 00:1d:92:ea:cc:62 capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8168 driverversion=8.020.00-NAPI duplex=half latency=0 link=no multicast=yes port=twisted pair resources: irq:29 ioport:e800(size=256) memory:feaff000-feafffff memory:f8ff0000-f8ffffff(prefetchable) memory:feac0000-feadffff(prefetchable) *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: 00:15:af:72:a4:38 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bgn --- iwconfig ---- lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Wuggawoo" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Tx-Power=9 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on --- cat /etc/network/interfaces ---- auto lo iface lo inet loopback logs deamon.log --- Jan 19 04:17:09 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:11 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): association took too long. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 5 -> 6 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): asking for new secrets Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 6 -> 4 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 4 -> 5 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): connection 'Wuggawoo' has security, and secrets exist. No new secrets needed. Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'ssid' value 'Wuggawoo' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'scan_ssid' value '1' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'key_mgmt' value 'WPA-PSK' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'psk' value '<omitted>' Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_engine_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_module_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: set interface ap_scan to 1 Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:13 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:23 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:24 ubuntu AptDaemon: INFO: Initializing daemon Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:25 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:27 ubuntu NetworkManager: <info> wlan0: link timed out. --- kern.log --- Jan 19 04:18:11 ubuntu kernel: [ 142.420024] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:13 ubuntu kernel: [ 144.333847] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:13 ubuntu kernel: [ 144.539996] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:13 ubuntu kernel: [ 144.750027] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:14 ubuntu kernel: [ 144.940022] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:25 ubuntu kernel: [ 155.832995] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:25 ubuntu kernel: [ 156.030046] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:25 ubuntu kernel: [ 156.230039] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:25 ubuntu kernel: [ 156.430039] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out --- syslog --- Jan 19 04:18:46 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:18:48 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:18:48 ubuntu kernel: [ 178.833905] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:48 ubuntu kernel: [ 179.030035] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:48 ubuntu kernel: [ 179.230020] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:48 ubuntu kernel: [ 179.433634] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out lspci and lsusb lspci -- 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:00.0 VGA compatible controller: nVidia Corporation G80 [GeForce 8800 GTS] (rev a2) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 03:00.0 FireWire (IEEE 1394): JMicron Technology Corp. IEEE 1394 Host Controller -- lsusb -- Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 003: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Bus 004 Device 002: ID 045e:0730 Microsoft Corp. Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 13d3:3247 IMC Networks 802.11 n/g/b Wireless LAN Adapter Bus 002 Device 002: ID 0718:0628 Imation Corp. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 046d:08c2 Logitech, Inc. QuickCam PTZ Bus 001 Device 002: ID 0424:2228 Standard Microsystems Corp. 9-in-2 Card Reader Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub With no security on my router I still can't connect, I get: Jan 19 15:58:01 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: WPS-AP-AVAILABLE Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Association request to the driver failed Jan 19 15:58:02 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 15:58:05 ubuntu NetworkManager: <info> wlan0: link timed out. Jan 19 15:58:07 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connec

  Read the article

• What happens to missed writes after a zpool clear?

  - by Kevin

  I am trying to understand ZFS' behaviour under a specific condition, but the documentation is not very explicit about this so I'm left guessing. Suppose we have a zpool with redundancy. Take the following sequence of events: A problem arises in the connection between device D and the server. This causes a large number of failures and ZFS therefore faults the device, putting the pool in degraded state. While the pool is in degraded state, the pool is mutated (data is written and/or changed.) The connectivity issue is physically repaired such that device D is reliable again. Knowing that most data on D is valid, and not wanting to stress the pool with a resilver needlessly, the admin instead runs zpool clear pool D. This is indicated by Oracle's documentation as the appropriate action where the fault was due to a transient problem that has been corrected. I've read that zpool clear only clears the error counter, and restores the device to online status. However, this is a bit troubling, because if that's all it does, it will leave the pool in an inconsistent state! This is because mutations in step 2 will not have been successfully written to D. Instead, D will reflect the state of the pool prior to the connectivity failure. This is of course not the normative state for a zpool and could lead to hard data loss upon failure of another device - however, the pool status will not reflect this issue! I would at least assume based on ZFS' robust integrity mechanisms that an attempt to read the mutated data from D would catch the mistakes and repair them. However, this raises two problems: Reads are not guaranteed to hit all mutations unless a scrub is done; and Once ZFS does hit the mutated data, it (I'm guessing) might fault the drive again because it would appear to ZFS to be corrupting data, since it doesn't remember the previous write failures. Theoretically, ZFS could circumvent this problem by keeping track of mutations that occur during a degraded state, and writing them back to D when it's cleared. For some reason I suspect that's not what happens, though. I'm hoping someone with intimate knowledge of ZFS can shed some light on this aspect.

  Read the article

• Why is Perl Cgiwrap Sock refusing connection to nginx?

  - by Emmanuel

  Could anyone shed some light on the following line in my nginx error logs. I'm trying to get Perl and Nginx talking to each other, but so far no success. unix:/var/run/nginx/cgiwrap-dispatch.sock failed (111: Connection refused)2011/11/20 09:18:34 [error] 24054#0: *1186 connect() to unix:/var/run/nginx/cgiwrap-dispatch.sock failed (111: Connection refused) while connecting to upstream, client: 150.101.221.75, server: example.com, request: "GET /dspam.cgi HTTP/1.1", upstream: "fastcgi://unix:/var/run/nginx/cgiwrap-dispatch.sock:", host: "example.com" The relevant nginx configs. location ~ \.cgi$ { gzip off; include /etc/nginx/fastcgi_params; fastcgi_pass unix:/var/run/fcgiwrap.socket; fastcgi_index index.pl; fastcgi_param SCRIPT_FILENAME /var/www/dspam$fastcgi_script_name; }

  Read the article

• Can you use gzip over SSL? And Connection: Keep-Alive headers

  - by magenta

  I'm evaluating the front end performance of a secure (SSL) web app here at work and I'm wondering if it's possible to compress text files (html/css/javascript) over SSL. I've done some googling around but haven't found anything specifically related to SSL. If it's possible, is it even worth the extra CPU cycles since responses are also being encrypted? Would compressing responses hurt performance? Also, I'm wanting to make sure we're keeping the SSL connection alive so we're not making SSL handshakes over and over. I'm not seeing Connection: Keep-Alive in the response headers. I do see Keep-Alive: 115 in the request headers but that's only keeping the connection alive for 115 milliseconds (seems like the app server is closing the connection after a single request is processed?) Wouldn't you want the server to be setting that response header for as long as the session inactivity timeout is? I understand browsers don't cache SSL content to disk so we're serving the same files over and over and over on subsequent visits even though nothing has changed. The main optimization recommendations are reducing the number of http requests, minification, moving scripts to bottom, image optimization, possible domain sharding (though need to weigh the cost of another SSL handshake), things of that nature.

  Read the article

• How to launch a remote process through ssh and end the connection?

  - by Lukasz Lew

  This is still blocking: ssh host nohup cmd This still leaves the connection open: ssh host nohup cmd &

  Read the article

• How can I prevent 'objects you are adding to the designer use a different data connection...'?

  - by Timothy Khouri

  I am using Visual Studio 2010, and I have a LINQ-to-SQL DBML file that my colleagues and I are using for this project. We have a connection string in the web.config file that the DBML is using. However, when I drag a new table from my "Server Explorer" onto the DBML file... I get presented with a dialog that demands that do one of these two options: Allow visual studio to change the connection string to match the one in my solution explorer. Cancel the operation (meaning, I don't get my table). I don't really care too much about the debate as why the PMs/devs who made this tool didn't allow a third option - "Create the object anyway - don't worry, I'm a developer!" What I am thinking would be a good solution is if I can create a connection in the Server Explorer - WITHOUT A WIZARD. If I can just paste a connection string, that would be awesome! Because then the DBML designer won't freak out on me :O) If anyone knows the answer to this question, or how to do the above, please lemme know!

  Read the article

• How can I use Windows Firewall to only permit the Windows Update service to make an outbound connection?

  - by microsmash

  I'm trying to tailor my Windows Firewall settings (using the Windows Firewall with Advanced Security console) to only permit programs that need to access the Internet with an outbound connection to do so. This works fine for normal applications as I can just allow the program, but services that load in the svchost.exe process are a problem. The only services I actually need to give access to are Windows Update and the Background Intelligent Transfer Service (and even that, I would only like Windows Update to be able to submit jobs to, but that's another issue.) Is there a method to only allow these to be permitted an outbound connection, and not any of the other services loaded in svchost?

  Read the article

• PPP connection between PalmOS and Ubuntu (over ttyUSB0?) without crashy "visor" kernel module

  - by Chris Boyle

  I have a Palm Treo 680 which I'd like to use as a media remote, using Palm MPC. Almost the exact instructions on that page used to work perfectly for establishing a PPP connection over the USB cable; I think I last tried it in Ubuntu 9.04 (Jaunty). In Karmic, I find that /dev/ttyUSB{0,1} are not present by default, and when I modprobe visor to get them, the Palm immediately crashes and reboots, as seen in Ubuntu bug 522753 (it reboots again as long as the module is still loaded and USB is still connected). The usbserial module has the same result. From reading that bug and elsewhere, it appears that the visor module is abandoned, and jpilot and friends use some other approach to talk to PalmOS over USB these days, which might not even involve a ttyUSB device. My question is, therefore: How do I create a PPP connection between PalmOS and Karmic without crashing the Palm?

  Read the article

• How can I create persistent SSH connection to "stream" commands over a period of time?

  - by Darth

  Say that I have an application running on one PC that is sending commands via SSH to another PC on the network (both machines running Linux). For example every time something happens on #1, I want to run a task on #2. In this setup, I have to create SSH connection on every single command. Is there any simple way to do this with basic unix tools without programming custom client/server application? Basically all I want is to establish a connection over SSH and then send one command after another.

  Read the article

• How to configure MySQL connection properties with Spring, Hibernate 3.3 and c3p0?

  - by sfussenegger

  I am currently in the process of upgrading an application from Hibernate 3.2 to Hibernate 3.3. I though I'd stick with the default connection pool (Hibernate changed its default from Commons DBCP to c3p0) as I don't have any good reason to choose a non-default pool. At least non but having used DBCP before. The upgrade went pretty much without any problems so far. The only thing I can't get to work is passing properties to the underlying MySQL JDBC4Connection. Up to now, I used DBCP's BasicDataSource.addConnectionProperty(String,String) to pass properties (useUnicode=true, characterEncodin=UTF-8, characterSetResults=UTF-8, zeroDateTimeBehavior=convertToNull). However, I can't find any way to do the same with c3p0 other than including them in the JDBC URL. (That's something I'd like to avoid as I wanna keep the URL configurable without forcing users to include those parameters.) So far, I've tried to use a ConnectionCustomizer without success. Any other suggestions?

  Read the article

• Server hard disk read speed and client download speed, is there a connection? [closed]

  - by Mywiki Witwiki

  Ok so a client's download speed is only as fast as a server's upload speed, and vice versa. Based on the answers to this post: Does upload speed depend upon download speed of the server? In other words, the data transfer rate between the two computers is only as fast as the speed of the "bottleneck". Let's pretend the two computers are in two different networks and both have 100Mbps internet connection. Ben wants a copy of a file in Mark's computer hard disk with 30Mbps read speed. Does this mean that Ben can download the file at a speed of around 30Mbps only, despite having an internet connection faster than 30Mbps?

  Read the article

• Is there any way to limit my Internet connection to a per program basis?

  - by Igoru

  My Linux connection is REALLY free. I live in Brazil, so where I live I can only have 1 Mbit/s. Yes I know it's sad, but it's not the point. Everytime I'm updating my Ubuntu 9.04 or downloading something, it does eat all my bandwidth. Like, while update-manager is downloading the packages, I can see by netspeed applet in my panel that the incoming traffic goes to 110 kB/s. And then, my Emesene suddenly goes disconnected, and I can't navigate. As you can imagine, I can't use my Internet connection again until the packages are all downloaded or I cancel the update in the middle. As I said, same thing happens when I'm dowloading something, but less intrusive and immediate. The question is: is there any way to limit that APT/downloads traffic to some way I can still use my other Internet services, or to reserve some bandwidth for common navigation tasks (like we have on Windows, but I forgot this thing's name, it's like "something packages".

  Read the article

• Why is my connection to Playstation Network so unreliable? [closed]

  - by jammus

  Hello friends. I'm 28 and my girlfriend is 24. Our home internet connection is pretty reliable, it's almost always up and can get fairly high download speeds. However, my experience with the Playstation Network is pretty frustrating. I'm always getting kicked off or getting quite high latency. Are there any tips or tricks that you might help my on-line gaming run more smoothly? I'm using a wireless connection for the PS3, is this likely to affect things?

  Read the article

• Zimbra Relaying from Postfix connection timed out sending multiple emails?

  - by liamTc

  I have a web server setup with postfix which is relaying email to a zimbra server. This working fine however I have attempted to send a few thousand emails and now the connection from postfix to zimbra is timing out. All of the emails have been deferred on the postfix queue. If I try to send individual emails from postfix to zimbra it works fine. But if I try to flush the postfix queue all of the emails time out. In mail.log the emails look like this: postfix/error[2494]: 32B0950C04: to=, relay=none, delay=19431, delays=19402/29/0/0.01, dsn=4.4.1, status=deferred (delivery temporarily suspended: connect to mail.server.com[123.45.678.91]:25: Connection timed out) I have also noticed that in the above message it says "relay=none" for these emails that are failing. But the emails that do send say "relay=domainname.com". How I can resolve this, by sending the emails in the queue and avoiding this from happening again?

  Read the article

• On Mac OS X how can I monitor what is using my internet connection?

  - by Jon Hopkins

  I've got a relatively limited broadband connection (I live miles from the nearest exchange) and from time to time net access (but nothing else) slows to a near crawl. I know from a bit of monitoring software that the connection is being fairly heavily used which would explain it but I don't know what's using it. There are certainly plenty of things which might (these days there are dozens of apps that will either regularly or infrequently check data or download updates) but how can I find out? I'm happy to pay (a small amount of) money if needed, though in that case I'd rather it were a recommendation that me just Googling for something.

  Read the article

• How to setup a tunneled connection to a NAS?

  - by Jan

  Hi there, While looking into alternatives for Dropbox I explored the idea of a NAS. It would be easy to hook up the NAS to a broadband connection and have the users access the files. However, - The data needs to be encrypted on the NAS itself (in case it gets stolen). - The connection to the NAS needs to be secure (VPN?). - The drive needs to appear as a drive under windows (so no https). Any ideas? Thanks in advance, I can't seem to find the final solution! Jan

  Read the article

• How should I troubleshoot a problematic wireless connection on Linux?

  - by Gearoid Murphy

  I recently purchased a netgear 150 usb wireless dongle for use with my 11.10 Xubuntu amd64 system. Using the network-manager interface, I can see local wireless networks and enter the authentication details for my local wireless lan. Unfortunately, the connection does not seem to work, I keep getting notifications that my wireless has disconnected (but none indicating that I've connected). When I examine syslog, it seems to indicate that I've successfully associated with the wireless switch and that dhcp has successfully acquired an ip address but the log shows that the dhcp process keeps sending requests, eventually dropping the connection. 'ifconfig wlan0' never shows the dhcp address logged in syslog. I suspect that the problem lies with the usb dongle, my configuration or the wireless switch but I am not certain how to isolate the problem, can anyone provide some insight on how I should go about homing in on the cause of this problem or verifying the functionality of the individual components, thanks.

  Read the article

• How secure is using "Normal password" for SMTP with connection type = STARTTLS?

  - by harshath.jr

  I'm using an email client for the first time - for the most part I've always used gmail via the web interface. Now I'm setting up thunderbird to connect to an email server of my own (on my own server, own domain name, etc). The server machine (and the email server on it) was preconfigured for me. Now i figured out away by which I'm able to send and receive email, but I noticed that in the outgoing and incoming servers section, the connection type was STARTTLS (and not SSL/TLS), and the Authentication Type was "Normal Password". Does this mean that the password will be sent across in plain text? I'm very paranoid about security - its the only way that it works for me. Can someone please post links that explain how SMTP (my outbound server) and IMAP (my inbound server) servers work, and what connection type means what? Thanks! PS: If this question does not belong here, please redirect me.

  Read the article

• My python program always brings down my internet connection after several hours running, how do I debug and fix this problem?

  - by Shane

  I'm writing a python script checking/monitoring several server/websites status(response time and similar stuff), it's a GUI program and I use separate thread to check different server/website, and the basic structure of each thread is using an infinite while loop to request that site every random time period(15 to 30 seconds), once there's changes in website/server each thread will start a new thread to do a thorough check(requesting more pages and similar stuff). The problem is, my internet connection always got blocked/jammed/messed up after several hours running of this script, the situation is, from my script side I got urlopen error timed out each time it's requesting a page, and from my FireFox browser side I cannot open any site. But the weird thing is, the moment I close my script my Internet connection got back on immediately which means now I can surf any site through my browser, so it must be the script causing all the problem. I've checked the program carefully and even use del to delete any connection once it's used, still get the same problem. I only use urllib2, urllib, mechanize to do network requests. Anybody knows why such thing happens? How do I debug this problem? Is there a tool or something to check my network status once such situation occurs? It's really bugging me for a while... By the way I'm behind a VPN, does it have something to do with this problem? Although I don't think so because my network always get back on once the script closed, and the VPN connection never drops(as it appears) during the whole process.

  Read the article

• How to really change programmatically ip address without reboot (with no connection too)?

  - by DmitryI

  Really, I tried everything, and there is no solution that works for me. WMI - everything perfect, but I can't change ip address when there is no connection. O_o Are you joking me? How can I make a connection without correct Ip-address? IPHelper - not doing anything. Just adding address to the table. Not work after reboot. netsh - the stupid way I think, but ok, if you don't no another ways you can try. Before you will know, that network adapters name can contain international characters. Did someone know how it works actually, I mean inside? Registry - working after reboot. I don't want to reboot. May be someone know how to notify about reg entries changes?

  Read the article

• How can I connect a wired PC to the internet through my Macs wifi connection?

  - by David Weitz

  So I'll probably be buying a USB wifi adapater if I can't get this to work, but I'm trying. I have a wireless router at home and my Macbook Pro is connected to said wifi. My desktop doesn't have a wifi connection, but I've connected my macbook with my desktop via crossover cable. I enabled internet sharing on my macbook, but my Windows 7 desktop can't get a connection. I tried just regular file sharing and that works fine, but the internet sharing doesn't. I assume the goal is to get my PC to see my mac as the default gateway, but I've had no luck manually setting it. Here's the ifconfig output on my mac and my attempt at settings on windows: http://i.imgur.com/uJfUz.png

  Read the article

• How can I tell what command is running on the remote end of an ssh connection?

  - by user268385

  Tl;dr - how do I find the name of the command (eg $BASH_COMMAND) running on the remote end of an ssh connection? ... My example setup is two tmux vertical panes, LH pane runs a local vim session with vertical split, RH pane runs an ssh session running vim, again with a vertical split. Using tmux-navigator I can navigate from left to right over the first 3 vim buffers, but the 4th (far right hand one) is inaccessible. The reason for this is that tmux-navigator tests the value of 'pane_current_command' and compares it to 'vim' before deciding which keystrokes to dispatch. On the right hand tmux pane, the current command is 'ssh' and not 'vim'. What I want to do is test for (pane_current_command =~ 'ssh'), and if so, examine the command that is running on the far side of the connection? I cannot find a way to get hold of this, so any suggestions would be welcome? For information, the problem is almost the same as this one, but without the nested tmux sessions: https://github.com/christoomey/vim-tmux-navigator/issues/12

  Read the article

• Do TCP/UDP connections add to the Windows incoming connection limit?

  - by user47899

  Hi all, I've tried to figure out what Microsoft means by "Windows sockets" and it all seems very vague. Basically we have customers that sometimes try to set up workgroups with close to 10 Windows XP computers with drive and printer shares and we're worried that some of the non-Windows Ethernet devices on the network will cause issues with the inbound connection limit outlined here where only 10 inbound connections can be active at one time. For example, there is an Ethernet Caller ID device that broadcasts UDP packets to all computers, and a kitchen display system that likewise broadcasts UDP. They may also have incoming TCP packets for our custom online ordering module. Do these TCP/UDP connections count toward the inbound connection limit? I'm aware that Windows 7 has increased the limit to 20 but we might have future customers that will push that limit. Thanks in advance

  Read the article

• Is it possible to restrict the connection duration per client on the router (say with OpenWRT)?

  - by static

  How to limit the connection duration per client per period (say, one MAC-address can connect only for 3 hours per week to the network). Where could be defined such a rule? In the firewall? So the rule should define not statically times (this is simple), when the client is allowed to access the network, but the duration of the connection per day/week/month, etc. How/where to implement such rules? Is it possible to do so with OpenWRT/DD-WRT?

  Read the article

• How can I minimize the amount my router slows down my Internet connection speed?

  - by Lord Torgamus

  Background I'm working with what I assume is a pretty common Internet setup: a cable modem, a wireless router and a few Internet-connected devices. Lately, I've started being more demanding on my Internet connection, and noticed that using my router slows down my download speeds considerably. I just kind of dealt with it until Zune Marketplace on the Xbox 360 told me that a movie was going to take well over ten hours to download, and I just didn't want to wait that long. Good little scientist that I am, I tried to reduce the problem down to one variable. The test As a control, I turned off all the devices in the house that use wireless Internet, and unplugged all the wired devices except for the Xbox. I also power-cycled both the modem and the router. I then tried to download the movie again, and was told that it would still take over ten hours. Next, I unplugged the router, and connected the Xbox directly to the modem. The movie downloaded in just over one hour. As far as I can tell, this means that my ISP, other cable users near me, the remote servers, anything wireless-related and my machines' disk speeds can't be at fault. A similar experiment that replaced the Xbox with a wired laptop produced similar results. To me, this says "the router is responsible for things taking around ten times longer to download." My question I'd still prefer to use the router for a few reasons: it's a pain to connect and disconnect everything every time there's a big file to download direct connection to the modem isn't good for security only one machine can be connected directly to the modem at a time What can I do to have fast connection speeds while still using the router? I don't mind turning other machines off, as long as I don't have to mess with power and ethernet cables. EDIT : After asking this followup question and then this one, I installed dd-wrt on my router, and I seem to be getting higher and more consistent speeds. Perhaps more importantly, my memory use is fairly constant. I know this isn't an answer — which is why I'm not posting it as an answer — but it is how I resolved the situation, and hopefully it'll be helpful for someone.

  Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >