Search Results

Search found 3661 results on 147 pages for 'cross vander'.

Page 133/147 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

  • What would make a noise in a PC on graphics operations on a passively-cooled system?

    - by T.J. Crowder
    I have this system based on the Intel D510MO motherboard, which is basically an Atom D510 (dual-core HT Atom w/built-in GPU), an Intel NM10 chipset, and a Realtek Gigabit LAN controller. It's entirely passively cooled. I noticed almost immediately that there was a kind of very, very soft noise that corresponded with graphics operations, sort of the noise you'd get if you had a sheet of flat paper and slid something really light across it — but more electronic than that. I wrote it off as observation error and/or disk activity triggered by the graphics operation (although the latter seemed like a lot of unnecessary disk activity). It isn't. I got curious enough that I finally did a few controlled experiments, and here's what I've determined: It isn't the HDD. For one thing, the sounds the HDD makes (when seeking, when reading or writing, when just sitting there spinning) is different. For another, I used sudo hdparm -y /dev/sda (I'm using Ubuntu 10.04 LTS) to temporarily put the disk on standby while making sure that non-disk graphics op was happening in a loop. The disk spun down, but the other sound continued, corresponding perfectly with the timing of the graphics op. (Then the disk spun up again, but it takes long enough that I could rule out the HDD.) It isn't the monitor; I ensured the two were well physically-separated and the sound was definitely coming from the main box. It isn't something else in the room; the sound is coming from the box. It isn't cross-talk to an audio circuit coming out the speakers. (It doesn't have any speakers.) It isn't my mouse (e.g., when I'm trying to make graphics ops happen); the sound happens if I set up a recurring operation and don't use the mouse at all, or if I lift the mouse off the table slightly (but enough that the laser still registers movement). It isn't the voices in my head; they never whisper like that. Other observations: It doesn't seem to matter what the graphics operation is; anything that changes what's on the screen seems to do it. I get the sound when moving the mouse over the Chromium tab bar (which makes the tab backgrounds change); I get it when a web page has a counter on it that changes the text on the page: I get it when dragging window contents around. The sound is very, very slightly louder if the graphics op is larger, like scrolling a text area when writing a question on superuser.com, than for smaller operations like the tick counter on the web page. But it's very slight. It's fairly loud (and of good duration) when the op involves color changes to substantial surface areas. For instance, when asking a question here on superuser and you move the cursor between the question box and the tag box, and the help to the right fades out, changes, and fades back in. (Yet another example related to the web browser, so let me say: I hear it when operations completely unrelated to the web browser as well.) It doesn't sound like arcing or anything like that (I'd've shut off the machine Right Quick Like if it did). Moving windows does it. Scrolling windows (by and large) doesn't. I have the feeling I've heard this sort of thing before, when all system fans were on low and such, with other systems — but (again) written it off as observational error. For all the world it's like I'm hearing the CPU working (as opposed to the GPU; note the window scroll thing above) or data being transferred somewhere, but that just seems...unlikely. So what am I hearing? This may seem like a very localized question, but perhaps other silent PC enthusiasts may be interested as well...

    Read the article

  • Neighbour table overflow on Linux hosts related to bridging and ipv6

    - by tim
    Note: I already have a workaround for this problem (as described below) so this is only a "want-to-know" question. I have a productive setup with around 50 hosts including blades running xen 4 and equallogics providing iscsi. All xen dom0s are almost plain Debian 5. The setup includes several bridges on every dom0 to support xen bridged networking. In total there are between 5 and 12 bridges on each dom0 servicing one vlan each. None of the hosts has routing enabled. At one point in time we moved one of the machines to a new hardware including a raid controller and so we installed an upstream 3.0.22/x86_64 kernel with xen patches. All other machines run debian xen-dom0-kernel. Since then we noticed on all hosts in the setup the following errors every ~2 minutes: [55888.881994] __ratelimit: 908 callbacks suppressed [55888.882221] Neighbour table overflow. [55888.882476] Neighbour table overflow. [55888.882732] Neighbour table overflow. [55888.883050] Neighbour table overflow. [55888.883307] Neighbour table overflow. [55888.883562] Neighbour table overflow. [55888.883859] Neighbour table overflow. [55888.884118] Neighbour table overflow. [55888.884373] Neighbour table overflow. [55888.884666] Neighbour table overflow. The arp table (arp -n) never showed more than around 20 entries on every machine. We tried the obvious tweaks and raised the /proc/sys/net/ipv4/neigh/default/gc_thresh* values. FInally to 16384 entries but no effect. Not even the interval of ~2 minutes changed which lead me to the conclusion that this is totally unrelated. tcpdump showed no uncommon ipv4 traffic on any interface. The only interesting finding from tcpdump were ipv6 packets bursting in like: 14:33:13.137668 IP6 fe80::216:3eff:fe1d:9d01 > ff02::1:ff1d:9d01: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:9d01, length 24 14:33:13.138061 IP6 fe80::216:3eff:fe1d:a8c1 > ff02::1:ff1d:a8c1: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:a8c1, length 24 14:33:13.138619 IP6 fe80::216:3eff:fe1d:bf81 > ff02::1:ff1d:bf81: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:bf81, length 24 14:33:13.138974 IP6 fe80::216:3eff:fe1d:eb41 > ff02::1:ff1d:eb41: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:eb41, length 24 which placed the idea in my mind that the problem maybe related to ipv6, since we have no ipv6 services in this setup. The only other hint was the coincidence of the host upgrade with the beginning of the problems. I powered down the host in question and the errors were gone. Then I subsequently took down the bridges on the host and when i took down (ifconfig down) one particularly bridge: br-vlan2159 Link encap:Ethernet HWaddr 00:26:b9:fb:16:2c inet6 addr: fe80::226:b9ff:fefb:162c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:120 errors:0 dropped:0 overruns:0 frame:0 TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5286 (5.1 KiB) TX bytes:726 (726.0 B) eth0.2159 Link encap:Ethernet HWaddr 00:26:b9:fb:16:2c inet6 addr: fe80::226:b9ff:fefb:162c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1801 errors:0 dropped:0 overruns:0 frame:0 TX packets:20 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:126228 (123.2 KiB) TX bytes:1464 (1.4 KiB) bridge name bridge id STP enabled interfaces ... br-vlan2158 8000.0026b9fb162c no eth0.2158 br-vlan2159 8000.0026b9fb162c no eth0.2159 The errors went away again. As you can see the bridge holds no ipv4 address and it's only member is eth0.2159 so no traffic should cross it. Bridge and interface .2159 / .2157 / .2158 which are in all aspects identical apart from the vlan they are connected to had no effect when taken down. Now I disabled ipv6 on the entire host via sysctl net.ipv6.conf.all.disable_ipv6 and rebooted. After this even with bridge br-vlan2159 enabled no errors occur. Any ideas are welcome.

    Read the article

  • PXE Boot not working

    - by Nishant
    Please explain the error in this screenshot DHCP Setting: This screenshot was taken after powering off the old comp hence he server interface is shown as the wireless card - it becomes 192.168.0.1 when I connect wires and power up the old laptop to boot via PXE. My scenario is simple. An old laptop and a new laptop . A cross over cable ( that I myself made from CAT 6 cable by cutting it and connecting 4 wires as mentioned in some doc). The new laptop ( tftp server ) has a Wirelss Card ( with which I am browsing and writing this ) . And the cable is connected between laptops . TFTP server ( new laptop details ) Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::f511:3d4a:ca01:122e%16 IPv4 Address. . . . . . . . . . . : 192.168.0.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.2 Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Achilles Link-local IPv6 Address . . . . . : fe80::99b1:8ae0:9e6c:f300%11 IPv4 Address. . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.2.1

    Read the article

  • Do email forms need to be santized before sending?

    - by levi
    I have a client that keeps getting reports from godaddy's "websiteprotection.com" stating how the website is insecure. Your website contains pages that do not properly sanitize visitor-provided input to make sure it contains no malicious content or scripts. Cross-site scripting vulnerabilities let malicious users execute arbitrary HTML or script code in another visitor's browser. Output: The request string used to detect this flaw was : /cross_site_scripting.?nasl.asp The output was : HTTP/1.1 404 Not Found\r Date: Wed, 21 Mar 2012 08:12:02 GMT\r Server: Apache\r X-Pingback:http://?CLIENTSWEBSITE.com/?xmlrpc.php\r Expires: Wed, 11 Jan 1984 05:00:00 GMT\r Cache-Control: no-cache, must-revalidate, max-age=0\r Pragma: no-cache\r Set-Cookie: PHPSESSID=?1jsnhuflvd59nb4trtquston50; path=/\r Last-Modified: Wed, 21 Mar 2012 08:12:02 GMT\r Keep-Alive: timeout=15, max=100\r Connection: Keep-Alive\r Transfer-Encoding: chunked\r Content-Type: text/html; charset=UTF-8\r \r <div id="contact-form" class="widget"><form action="http://?CLIENTSWEBSITE.c om/<script>cross_site_?scripting.nasl</script>.asp" id="contactForm" meth od="post"> It looks like it has an issue with the contact form. All the contact form does is posts an ajax request to the same page, and than a PHP script mails the data (no database stuff). Is there any a security issues here? Any ideas on how I can satisfy the security scanner? Here is the form and script: <form action="<?php echo $this->getCurrentUrl(); ?>" id="contactForm" method="post"> <input type="text" name="Name" id="Name" value="" class="txt requiredField name" /> //Some more text inputs <input type="hidden" name="sendadd" id="sendadd" value="<?php echo $emailadd ; ?>" /> <input type="hidden" name="submitted" id="submitted" value="true" /><input class="submit" type="submit" value="Send" /> </form> // Some initial JS validation, if that passes an ajax post is made to the script below //If the form is submitted if(isset($_POST['submitted'])) { //Check captcha if (isset($_POST["captchaPrefix"])) { $capt = new ReallySimpleCaptcha(); $correct = $capt->check( $_POST["captchaPrefix"], $_POST["Captcha"] ); if( ! $correct ) { echo false; die(); } else { $capt->remove( $_POST["captchaPrefix"] ); } } $dateon = $_POST["dateon"]; $ToEmail = $_POST["sendadd"]; $EmailSubject = 'Contact Form Submission from ' . get_bloginfo('title'); $mailheader = "From: ".$_POST["Email"]."\r\n"; $mailheader .= "Reply-To: ".$_POST["Email"]."\r\n"; $mailheader .= "Content-type: text/html; charset=iso-8859-1\r\n"; $MESSAGE_BODY = "Name: ".$_POST["Name"]."<br>"; $MESSAGE_BODY .= "Email Address: ".$_POST["Email"]."<br>"; $MESSAGE_BODY .= "Phone: ".$_POST["Phone"]."<br>"; if ($dateon == "on") {$MESSAGE_BODY .= "Date: ".$_POST["Date"]."<br>";} $MESSAGE_BODY .= "Message: ".$_POST["Comments"]."<br>"; mail($ToEmail, $EmailSubject, $MESSAGE_BODY, $mailheader) or die ("Failure"); echo true; die(); }

    Read the article

  • Error on installing SVN extension with pecl

    - by thedp
    Hello, I'm trying to install the following PHP extension: http://php.net/manual/en/book.svn.php But when I do pecl install svn-beta I receive an error message that it can't locate the svn_client.h file. I searched the net but couldn't find any useful reference to this error. Thank you for your help. Installation result: root@myUbuntu:/home/thedp# pecl install svn-beta downloading svn-0.5.1.tgz ... Starting to download svn-0.5.1.tgz (23,563 bytes) .....done: 23,563 bytes 4 source files, building running: phpize Configuring for: PHP Api Version: 20041225 Zend Module Api No: 20060613 Zend Extension Api No: 220060519 1. Please provide the prefix of Subversion installation : autodetect 1-1, 'all', 'abort', or Enter to continue: 1. Please provide the prefix of the APR installation used with Subversion : autodetect 1-1, 'all', 'abort', or Enter to continue: building in /var/tmp/pear-build-root/svn-0.5.1 running: /tmp/pear/temp/svn/configure --with-svn --with-svn-apr checking for grep that handles long lines and -e... /bin/grep checking for egrep... /bin/grep -E checking for a sed that does not truncate output... /bin/sed checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes checking whether we are cross compiling... no checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether gcc accepts -g... yes checking for gcc option to accept ISO C89... none needed checking whether gcc and cc understand -c and -o together... yes checking for system library directory... lib checking if compiler supports -R... no checking if compiler supports -Wl,-rpath,... yes checking build system type... i686-pc-linux-gnu checking host system type... i686-pc-linux-gnu checking target system type... i686-pc-linux-gnu checking for PHP prefix... /usr checking for PHP includes... -I/usr/include/php5 -I/usr/include/php5/main -I/usr/include/php5/TSRM -I/usr/include/php5/Zend -I/usr/include/php5/ext -I/usr/include/php5/ext/date/lib -D_LARGEFILE_SOURCE -D_FILE_OFFSET_BITS=64 checking for PHP extension directory... /usr/lib/php5/20060613+lfs checking for PHP installed headers prefix... /usr/include/php5 checking for re2c... no configure: WARNING: You will need re2c 0.12.0 or later if you want to regenerate PHP parsers. checking for gawk... no checking for nawk... nawk checking if nawk is broken... no checking for svn support... yes, shared checking for specifying the location of apr for svn... yes, shared checking for svn includes... configure: error: failed to find svn_client.h ERROR: `/tmp/pear/temp/svn/configure --with-svn --with-svn-apr' failed

    Read the article

  • Bridging a non-persistent PPP connection to wireless (or wired) in Windows XP

    - by phooze
    I have a 3G modem-like device (eMobile's D01NX, PC card style, for any Japan nerds out there) that I use to connect my PC to the Internet. I'd like to bridge this connection with another computer either via an ad-hoc wireless network, or a simple cross-over cable (either are options). However, when I open "Network Connections", I do not see the PPP connection (otherwise I could click both and bridge). I believe this is because there is software (provided by the vendor) that is handling the card directly and registering a PPP connection dynamically. When connected, an ipconfig at the command line yields: Ethernet adapter wireless: Connection-specific DNS Suffix . : Autoconfiguration IP Address. . . : 169.254.5.169 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Ethernet adapter lan: Media State . . . . . . . . . . . : Media disconnected PPP adapter {B59EEDDE-A22B-48DF-93E5-04842B641257}: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 114.xx.xxx.xx Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 114.xx.xxx.xx (I've commented out my IP address for privacy reasons, but what does appear there is a functional Internet IP address.) When I disconnect the adapter with the vendor software, the PPP connection disappears completely from the ipconfig list. Any ideas on how to do this?

    Read the article

  • File copying utility like rsync with error handling like ddrescue, for data recovery from a hard drive with bad sectors or hardware failure

    - by purefusion
    I have a hard drive with either bad blocks or sectors that are failing to read due to potential mechanical issues, such as a bad disk head, bad motor, or some other issue that is causing the hard drive to read data excruciatingly slowly and with lots of read errors. I'm seeing an average of 50 KB/sec, with some reads dropping below 10 KB/sec, and frequently it gets stuck on a file or sector altogether, usually for quite a long time—from 2-10 minutes or more (when using rsync, before it times out). Speed seems to vary wildly, and it gets stuck on files a lot, and when it finally gets "unstuck" it only seems to last for a short burst before it gets stuck again. The drive is also very quiet with only an occasional sound of files copying (usually when it gets stuck/unstuck for a brief time, before getting stuck again). Thus, there are none of those evil sounds that are normally associated with HDD death. Someone suggested that the problems sounded like they might be caused by a misaligned disk head, which requires a lot of re-reads before it finally reads data with success. Sounds plausible, but I digress... Anyway, the problem with rsync is that it seems to have no decent error handling support. Obviously, it wasn't meant for use in recovering data from failing hard drives, but all the so-called "data recovery" utilities out there that are meant for such use usually focus on recovery of deleted files or messed up partitions, rather than copying files off dying hard drives. Deleted file recovery is not what I need, obviously, so perhaps you can understand my disappointment in not being able to find what I'm after yet. Naturally, this is where you'd probably say "You should use ddrescue!" Well, that's all fine and dandy, but I've already got most of the data backed up, so I just want to recover certain files. I'm not concerned with trying to recover a full partition block-by-block as ddrescue does. I am only interested in rescuing just specific files and directories. Ideally, what I'd like is some sort of cross between rsync and ddrescue: something that lets me specify source and destination as directories of normal files like rsync (rather than two full partitions as ddrescue requires), with a way to skip files with errors in an initial run, and then allows me to attempt recovery of those files with errors in a later run (with a slightly altered command, of course), perhaps even offering an option to specify the number of retry attempts ...just like how ddrescue works with blocks, only I want a utility that works with specific files/directories like rsync does. So am I daydreaming here, or does something out there exist that can do this? Or, maybe even a way to make rsync or ddrescue work in such a way? I'm really open to whatever solutions might work, so long as they let me choose which files I want to "rescue", and can skip files with errors in the initial run, and try/retry those errors again later. So far I've tried rsync with the following options, but it often gets stuck on a file for longer than the timeout, and ideally I'd just like it to move on to the next file and come back later to the files it gets stuck on. I don't think that's possible though. Anyway, here's what I've been using up till now: rsync -avP --stats --block-size=512 --timeout=600 /path/to/source/* /path/to/destination/

    Read the article

  • How to validate referral support implemented for Active Dircetory server?

    - by user146560
    Please suggest me some utility or application, using which i want to test referral settings done. I want to test cross forest referenced reference. Among two DNS say 1 firstDNS.com user([email protected]) 2 SecondDNS.com user([email protected]) Below java code written to test active directory server setting. public void authenticateUser(String user, String password, String domain) throws AuthenticationException, NamingException { List<String> ldapServers = findLDAPServersInWindowsDomain("first.com"); if (ldapServers.isEmpty()) throw new NamingException("Can't locate an LDAP server (try nslookup type=SRV _ldap._tcp." + "first.com"+ ")"); Hashtable<String, String> props = new Hashtable<String, String>(); String principalName = "testUserFirst"+ "@" + "First.com"; props.put(Context.SECURITY_PRINCIPAL, principalName); props.put(Context.SECURITY_CREDENTIALS, password); props.put(Context.REFERRAL,"follow"); //props.put(Context.SECURITY_AUTHENTICATION, "anonymous"); Integer count = 0; for (String ldapServer : ldapServers) { try { count++; DirContext ctx = LdapCtxFactory.getLdapCtxInstance("ldap://" + ldapServer, props); SearchControls searchCtls = new SearchControls(); //Specify the attributes to return String returnedAtts[]={"sn","givenName","mail"}; searchCtls.setReturningAttributes(returnedAtts); //Specify the search scope searchCtls.setSearchScope(SearchControls.SUBTREE_SCOPE); //specify the LDAP search filter String searchFilter = "(&(objectClass=user)(sAMAccountName=" testUserSecond)(userPassword=usertest@3))"; //Specify the Base for the search String searchBase = "DC=second,DC=com"; //initialize counter to total the results int totalResults = 0; // Search for objects using the filter NamingEnumeration<SearchResult> answer = ctx.search(searchBase, searchFilter, searchCtls); return; } catch (CommunicationException e) { // this is what'll happen if one of the domain controllers is unreachable if (count.equals(ldapServers.size())) { // we've got no more servers to try, so throw the CommunicationException to indicate that we failed to reach an LDAP server throw e; } } } } private List<String> findLDAPServersInWindowsDomain(String domain) throws NamingException { List<String> servers = new ArrayList<String>(); Hashtable<String, String> env = new Hashtable<String, String>(); env.put(Context.INITIAL_CONTEXT_FACTORY, "com.sun.jndi.dns.DnsContextFactory"); env.put("java.naming.provider.url", "dns://"); DirContext ctx = new InitialDirContext(env); Attributes attributes = ctx.getAttributes("_ldap._tcp." + domain, new String[] { "SRV" }); // that's how Windows domain controllers are registered in DNS Attribute a = attributes.get("SRV"); for (int i = 0; i < a.size(); i++) { String srvRecord = a.get(i).toString(); // each SRV record is in the format "0 100 389 dc1.company.com." // priority weight port server (space separated) servers.add(srvRecord.split(" ")[3]); } ctx.close(); return servers; }

    Read the article

  • What networking hardware do I need in this situation (Fairpoint [ISP] "E-DIA" connection)?

    - by Tegeril
    Right away you'd probably want to say, "Well just ask Fairpoint." I've done that, a number of times in as many different ways I can phrase it and just keep hitting a brick wall where they will not commit to giving any useful information and instead recommend contracting an outside firm and spending a pile of money. Anyway... I'm trying to help a family member out with an office connection that is being setup. I've managed to scrape tiny details here and there from our discussions with the ISP (Fairpoint in Maine) about what is going to be done and what is going to be needed. This is the connection that is being setup: http://www.fairpoint.com/enterprise/vantagepoint/e-dia/index.jsp Information I have been given: Via this connection I can get IPs across different C blocks if that were necessary (it is not) Fairpoint is bringing hardware with them that they claim simply does the conversion from whatever line is coming in the building to ethernet, they have referred to this as the "Fairpoint Netvanta" which I know suggests a line of products that I have looked up, but some (most? all?) of those seems to handle all the routing that I saw. Fairpoint says that I need to bring my own router to sit behind their device. They have literally declined to even suggest products that have worked for other clients in the past and fall back on "any business router works, not a home router." That alone makes my head spin. Detail and clarity hit a brick wall from there. At one moment I got them to cough up that the router I provide needs to be able to do VPN tunneling but they typically fall back to "not a home router" and I was even given "just a business router, Cisco or something, it'll be $500-$1000". Now I know that VPN tunneling routers exist well below that price point and since this connection is going to one machine, possibly two only via ethernet, my desire to purchase networking hardware that over-delivers what I need is not very high. They are literally setting all this up, have provided no configuration details for after they finish, and expect me to just plunk a $500+ router behind it and cross my fingers or contract out to a third party company. If there were other options available for the location, I would have dropped them in a second, but there aren't. The device that is connected requires a static IP and I'm honestly a bit hazy on the necessity of an additional router behind their device and generally a bit over my head. I presume that the router needs to be able to serve external static IPs to its clients, but I really don't know what is going to show up when they come to do the install. This was originally going to be run via an ADSL bridge modem with a range of static IPs (which is easy and is currently setup properly) but the location is too far from the telco to get speeds that we really want for upload and this is also a connection that needs high availability. Any suggestions would be greatly appreciated (I see a number of options in the Cisco Small Business line and other competitors that aren't going to break the bank…), especially if you've worked with Fairpoint before! Thanks for reading my wall of text.

    Read the article

  • Network config / gear question

    - by mcgee1234
    I have been tasked with setting up a fairly straightforward rack in a data center (we do not even need a whole rack, but this is the smallest allotment available). In a nutshell, 4 to 6 servers need to be able to reach 2 (maybe 3) vendors. The servers needs to be reachable over the internet. A little more detail - the networks the servers need to reach are inside of the data center, and are "trusted". Connections to these networks will be achieved through intra data center cross connects. It is kind of like a manufacturing line where we receive data from one vendor (burst-able up to 200 Mbits), churn through it on the servers, and then send out data to another vendor (bursts up to 20 Mbits). This series of events is very latency sensitive, so much so that it is common practice not to use NAT or a firewall on these segments (or so I hear). To reach the servers over the internet, I plan to use a site to site VPN. (This part is only relevant as far as hardware selection goes). I have 2 configurations in mind: Cisco 2911 (2921) (with the additional wan ports module) and a layer 2 switch - in this scenario, I would use the router also for VPN. Cisco 3560 layer 3 switch to interconnect the networks inside of the data center and an ASA 5510 (which is total overkill, but the 5505 is not rack mountable) as a firewall for the Wan side (internet) and VPN. I envision the setup to be as follows: Internet - ASA - 3560 Vendors - 3560 - Servers The general idea is that the ASA acts as a firewall and VPN device and the 3560 does all the heavy lifting. The first is a fairly traditional setup but my concern is performance. The second is somewhat unorthodox in that the vendors are directly connected to the layer 3 switch without passing through a firewall. Based on my understanding however, a layer 3 switch will perform substantially better as it will do hardware (ASIC) vs. software switching. (Note that number 2 is a little over the budget, but not unworkable (double negative, ugh)) Since this is my first time dealing with a data center, I am not sure what the IP space is going to look like. I suspect I will retain a block(s) of public IPs, vlan them to individual interfaces for the vendor connections and the servers (which will not reachable from the wan side of course) and setup routing on the switch. So here are my questionss: Is there a substantial performance difference between 1 and 2, i.e. hardware based switching on a layer 3 vs a software base on the 2911? I have trolled the internet and found a lot of Cisco literature, but nothing that I could really use to get a good handle. The vendors we connect to are secure and trusted (famous last words) and as I understand it, it is common practice not to NAT or firewall these connections (because of the aforementioned latency sensitivity). But what what kind of latency are we really talking about if I push the data through a router (or even ASA for that matter)? For our purposes, 5 ms will not kill us, 20 or 30 can be very costly. Others measure in microseconds, but they are out of our league. Is there any issues with using public IPs on a layer 3 switch? I am certainly not married to either of these configs, and I am totally open to any ideas. My knowledge (and I use the term loosely) is largely from books so I welcome any advice / insight. Thanks in advance.

    Read the article

  • CodeIgniter: Passing variables via URL - alternatives to using GET

    - by John Durrant
    I'm new to CodeIgniter and have just discovered the difficulties using the GET method of passing variables via the URL (e.g. domain.com/page.php?var1=1&var2=2). I gather that one approach is to pass the variables in the URI segments but haven't quite figured out how to do that yet as it seems to create the expectation of having a function in the controller named as the specific URI segment???? Anyway Instead of using GET I've decided to use POST by adapting a submit button (disguised as a link) with the variables in hidden input fields. I've created the following solution which seems to work fine, but am wondering whether I'm on the right track here or whether there is an easier way of passing variables via a link within CodeIgniter? I've created the following class in application/libraries/ <?php if ( ! defined('BASEPATH')) exit('No direct script access allowed'); class C_variables { function variables_via_link($action, $link_text, $style, $link_data) { $attributes = array('style' => 'margin:0; padding:0; display: inline;'); echo form_open($action, $attributes); $attributes = array('class' => $style, 'name' => 'link'); echo form_submit($attributes, $link_text); foreach ($link_data as $key => $value){ echo form_hidden($key, $value); } echo form_close(); } } ?> With the following CSS: /* SUBMIT BUTTON AS LINK adapted from thread: http://forums.digitalpoint.com/showthread.php?t=403667 Cross browser support (apparently). */ .submit_as_link { background: transparent; border-top: 0; border-right: 0; border-bottom: 1px solid #00F; border-left: 0; color: #00F; display: inline; margin: 0; padding: 0; cursor: hand /* Added to show hand when hovering */ } *:first-child+html .submit_as_link { /* hack needed for IE 7 */ border-bottom: 0; text-decoration: underline; } * html .submit_as_link { /* hack needed for IE 5/6 */ border-bottom: 0; text-decoration: underline; } Link then created using the following code in the VIEW: <?php $link = new C_variables; $link_data=array('var1' => 1, 'var2' => 2); $link ->variables_via_link('destination_page', 'here is a link!', 'submit_as_link', $link_data); ?> Thanks for your help...

    Read the article

  • iPhone OpenGL ES: How do I use gravity vector to correctly transform scene for augmented reality

    - by gpdawson
    I'm trying figure out how to get an OpenGL specified object to be displayed correctly according to the device orientation (ie. according to the gravity vector from the accelerometer, and heading from compass). The GLGravity sample project has an example which is almost like this (despite ignoring heading), but it has some glitches. For example, the teapot jumps 180deg as the device viewing angle crosses the horizon, and it also rotates spuriously if you tilt the device from portrait into landscape. This is fine for the context of this app, as it just shows off an object and it doesn't matter that it does these things. But it means that the code just doesn't work when you attempt to emulate real life viewing of an OpenGL object according to the device's orientation. What happens is that it almost works, but the heading rotation you apply from the compass gets "corrupted" by the spurious additional rotations seen in the GLGravity example project. Can anyone provide sample code that shows how to adjust correctly for the device orientation (ie. gravity vector), or to fix the GLGravity example so that it doesn't include spurious heading changes? //Clear matrix to be used to rotate from the current referential to one based on the gravity vector bzero(matrix, sizeof(matrix)); matrix[3][3] = 1.0; //Setup first matrix column as gravity vector matrix[0][0] = accel[0] / length; matrix[0][1] = accel[1] / length; matrix[0][2] = accel[2] / length; //Setup second matrix column as an arbitrary vector in the plane perpendicular to the gravity vector {Gx, Gy, Gz} defined by by the equation "Gx * x + Gy * y + Gz * z = 0" in which we arbitrarily set x=0 and y=1 matrix[1][0] = 0.0; matrix[1][1] = 1.0; matrix[1][2] = -accel[1] / accel[2]; length = sqrtf(matrix[1][0] * matrix[1][0] + matrix[1][1] * matrix[1][1] + matrix[1][2] * matrix[1][2]); matrix[1][0] /= length; matrix[1][1] /= length; matrix[1][2] /= length; //Setup third matrix column as the cross product of the first two matrix[2][0] = matrix[0][1] * matrix[1][2] - matrix[0][2] * matrix[1][1]; matrix[2][1] = matrix[1][0] * matrix[0][2] - matrix[1][2] * matrix[0][0]; matrix[2][2] = matrix[0][0] * matrix[1][1] - matrix[0][1] * matrix[1][0]; //Finally load matrix glMultMatrixf((GLfloat*)matrix);

    Read the article

  • Issues POSTing XML to OAuth and Signature Invalid with Ruby OAuth Gem

    - by thynctank
    [Cross-posted from the OAuth Ruby Google Group. If you couldn't help me there, don't worry bout it] I'm working on integrating a project with TripIt's OAuth API and am running into a weird issue. I authenticate fine, I store and retrieve the token/secret for a given user with no problem, I can even make GET requests to a number of services using the gem. But when I try using the one service I need POST for, I'm getting a 401 "invalid signature" response. Perhaps I'm not understanding how to pass in data to the AccessToken's post method, so here's a sample of my code: xml = <<-XML <Request> <Trip> <start_date>2008-12-09</start_date> <end_date>2008-12-27</end_date> <primary_location>New York, NY</primary_location> </Trip> </Request> XML` response = access_token.post('/v1/create', {:xml => xml}, {'Content-Type' => 'application/x-www-form-urlencoded'}) I've tried this with and without escaping the xml string before hand. The guys at TripIt seemed to think that perhaps the xml param wasn't getting included in the signature_base_string, but when I output that (from lib/signature/base.rb) I see: POST&https%3A%2F%2Fapi.tripit.com%2Fv1%2Fcreate&oauth_consumer_key %3D%26oauth_nonce %3Djs73Y9caeuffpmPVc6lqxhlFN3Qpj7OhLcfBTYv8Ww%26oauth_signature_method %3DHMAC-SHA1%26oauth_timestamp%3D1252011612%26oauth_token %3D%26oauth_version%3D1.0%26xml%3D%25253CRequest%25253E %25250A%252520%252520%25253CTrip%25253E%25250A %252520%252520%252520%252520%25253Cstart_date%25253E2008-12-09%25253C %252Fstart_date%25253E%25250A %252520%252520%252520%252520%25253Cend_date%25253E2008-12-27%25253C %252Fend_date%25253E%25250A %252520%252520%252520%252520%25253Cprimary_location%25253ENew %252520York%252C%252520NY%25253C%252Fprimary_location%25253E%25250A %252520%252520%25253C%252FTrip%25253E%25250A%25253C%252FRequest%25253E %25250A This seems to be correct to me. I output signature (from the same file) and the output doesn't match the oauth_signature param of the Auth header in lib/client/ net_http.rb. It's been URL-encoded in the auth header. Is this correct? Anyone know if the gem is broken/if there's a fix somewhere? I'm finding it hard to trace through some of the code.

    Read the article

  • Sort latitude and longitude coordinates into clockwise ordered quadrilateral

    - by Dave Jarvis
    Problem Users can provide up to four latitude and longitude coordinates, in any order. They do so with Google Maps. Using Google's Polygon API (v3), the coordinates they select should highlight the selected area between the four coordinates. Solutions and Searches http://www.geocodezip.com/map-markers_ConvexHull_Polygon.asp http://softsurfer.com/Archive/algorithm_0103/algorithm_0103.htm http://stackoverflow.com/questions/2374708/how-to-sort-points-in-a-google-maps-polygon-so-that-lines-do-not-cross http://stackoverflow.com/questions/242404/sort-four-points-in-clockwise-order http://en.literateprograms.org/Quickhull_%28Javascript%29 Graham's scan seems too complicated for four coordinates Sort the coordinates into two arrays (one by latitude, the other longitude) ... then? Jarvis March algorithm? Question How do you sort the coordinates in (counter-)clockwise order, using JavaScript? Code Here is what I have so far: // Ensures the markers are sorted: NW, NE, SE, SW function sortMarkers() { var ns = markers.slice( 0 ); var ew = markers.slice( 0 ); ew.sort( function( a, b ) { if( a.position.lat() < b.position.lat() ) { return -1; } else if( a.position.lat() > b.position.lat() ) { return 1; } return 0; }); ns.sort( function( a, b ) { if( a.position.lng() < b.position.lng() ) { return -1; } else if( a.position.lng() > b.position.lng() ) { return 1; } return 0; }); var nw; var ne; var se; var sw; if( ew.indexOf( ns[0] ) > 1 ) { nw = ns[0]; } else { ne = ns[0]; } if( ew.indexOf( ns[1] ) > 1 ) { nw = ns[1]; } else { ne = ns[1]; } if( ew.indexOf( ns[2] ) > 1 ) { sw = ns[2]; } else { se = ns[2]; } if( ew.indexOf( ns[3] ) > 1 ) { sw = ns[3]; } else { se = ns[3]; } markers[0] = nw; markers[1] = ne; markers[2] = se; markers[3] = sw; } What is a better approach? The recursive Convex Hull algorithm is overkill for four points in the data set. Thank you.

    Read the article

  • How do I use the gravity vector to correctly transform scene for augmented reality?

    - by gpdawson
    I'm trying figure out how to get an OpenGL specified object to be displayed correctly according to the device orientation (ie. according to the gravity vector from the accelerometer, and heading from compass). The GLGravity sample project has an example which is almost like this (despite ignoring heading), but it has some glitches. For example, the teapot jumps 180deg as the device viewing angle crosses the horizon, and it also rotates spuriously if you tilt the device from portrait into landscape. This is fine for the context of this app, as it just shows off an object and it doesn't matter that it does these things. But it means that the code just doesn't work when you attempt to emulate real life viewing of an OpenGL object according to the device's orientation. What happens is that it almost works, but the heading rotation you apply from the compass gets "corrupted" by the spurious additional rotations seen in the GLGravity example project. Can anyone provide sample code that shows how to adjust correctly for the device orientation (ie. gravity vector), or to fix the GLGravity example so that it doesn't include spurious heading changes? //Clear matrix to be used to rotate from the current referential to one based on the gravity vector bzero(matrix, sizeof(matrix)); matrix[3][3] = 1.0; //Setup first matrix column as gravity vector matrix[0][0] = accel[0] / length; matrix[0][1] = accel[1] / length; matrix[0][2] = accel[2] / length; //Setup second matrix column as an arbitrary vector in the plane perpendicular to the gravity vector {Gx, Gy, Gz} defined by by the equation "Gx * x + Gy * y + Gz * z = 0" in which we arbitrarily set x=0 and y=1 matrix[1][0] = 0.0; matrix[1][1] = 1.0; matrix[1][2] = -accel[1] / accel[2]; length = sqrtf(matrix[1][0] * matrix[1][0] + matrix[1][1] * matrix[1][1] + matrix[1][2] * matrix[1][2]); matrix[1][0] /= length; matrix[1][1] /= length; matrix[1][2] /= length; //Setup third matrix column as the cross product of the first two matrix[2][0] = matrix[0][1] * matrix[1][2] - matrix[0][2] * matrix[1][1]; matrix[2][1] = matrix[1][0] * matrix[0][2] - matrix[1][2] * matrix[0][0]; matrix[2][2] = matrix[0][0] * matrix[1][1] - matrix[0][1] * matrix[1][0]; //Finally load matrix glMultMatrixf((GLfloat*)matrix);

    Read the article

  • How do HttpOnly cookies work with AJAX requests?

    - by Shawn Simon
    JavaScript needs access to cookies if AJAX is used on a site with access restrictions based on cookies. Will HttpOnly cookies work on an AJAX site? Edit: Microsoft created a way to prevent XSS attacks by disallowing JavaScript access to cookies if HttpOnly is specified. FireFox later adopted this. So my question is: If you are using AJAX on a site, like StackOverflow, are Http-Only cookies an option? Edit 2: Question 2. If the purpose of HttpOnly is to prevent JavaScript access to cookies, and you can still retrieve the cookies via JavaScript through the XmlHttpRequest Object, what is the point of HttpOnly? Edit 3: Here is a quote from Wikipedia: When the browser receives such a cookie, it is supposed to use it as usual in the following HTTP exchanges, but not to make it visible to client-side scripts.[32] The HttpOnly flag is not part of any standard, and is not implemented in all browsers. Note that there is currently no prevention of reading or writing the session cookie via a XMLHTTPRequest. [33]. I understand that document.cookie is blocked when you use HttpOnly. But it seems that you can still read cookie values in the XMLHttpRequest object, allowing for XSS. How does HttpOnly make you any safer than? By making cookies essentially read only? In your example, I cannot write to your document.cookie, but I can still steal your cookie and post it to my domain using the XMLHttpRequest object. <script type="text/javascript"> var req = null; try { req = new XMLHttpRequest(); } catch(e) {} if (!req) try { req = new ActiveXObject("Msxml2.XMLHTTP"); } catch(e) {} if (!req) try { req = new ActiveXObject("Microsoft.XMLHTTP"); } catch(e) {} req.open('GET', 'http://beta.stackoverflow.com/', false); req.send(null); alert(req.getAllResponseHeaders()); </script> Edit 4: Sorry, I meant that you could send the XMLHttpRequest to the StackOverflow domain, and then save the result of getAllResponseHeaders() to a string, regex out the cookie, and then post that to an external domain. It appears that Wikipedia and ha.ckers concur with me on this one, but I would love be re-educated... Final Edit: Ahh, apparently both sites are wrong, this is actually a bug in FireFox. IE6 & 7 are actually the only browsers that currently fully support HttpOnly. To reiterate everything I've learned: HttpOnly restricts all access to document.cookie in IE7 & and FireFox (not sure about other browsers) HttpOnly removes cookie information from the response headers in XMLHttpObject.getAllResponseHeaders() in IE7. XMLHttpObjects may only be submitted to the domain they originated from, so there is no cross-domain posting of the cookies. edit: This information is likely no longer up to date.

    Read the article

  • Using FFMPEG to reliably convert videos to mp4 for iphone/ipod and flash players

    - by Jake Stevenson
    I need to convert videos for use in both a flash player and the iphone/ipod touch. I'm using the following batch script with ffmpeg: @echo off ffmpeg.exe -i %1 -s qvga -acodec libfaac -ar 22050 -ab 128k -vcodec libx264 -threads 0 -f ipod %2 This always outputs an mp4 file, and I can always play it on my PC. The videos also seem to play fine on my iphone 3GS. But with some input files it won't work for older iphone versions (3G and iPod touch). Here's the ffmpeg output from one such file: D:\ffmpeg>encode.bat d:\temp\recording.flv d:\temp\out.m4v FFmpeg version SVN-r18709, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --enable-memalign-hack --prefix=/mingw --cross-prefix=i686-ming w32- --cc=ccache-i686-mingw32-gcc --target-os=mingw32 --arch=i686 --cpu=i686 --e nable-avisynth --enable-gpl --enable-zlib --enable-bzlib --enable-libgsm --enabl e-libfaac --enable-libfaad --enable-pthreads --enable-libvorbis --enable-libtheo ra --enable-libspeex --enable-libmp3lame --enable-libopenjpeg --enable-libxvid - -enable-libschroedinger --enable-libx264 libavutil 50. 3. 0 / 50. 3. 0 libavcodec 52.27. 0 / 52.27. 0 libavformat 52.32. 0 / 52.32. 0 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0. 7. 1 / 0. 7. 1 built on Apr 28 2009 04:04:42, gcc: 4.2.4 [flv @ 0x187d650]skipping flv packet: type 18, size 164, flags 0 Input #0, flv, from 'd:\temp\recording.flv': Duration: 00:00:07.17, start: 0.001000, bitrate: N/A Stream #0.0: Video: flv, yuv420p, 320x240, 1k tbr, 1k tbn, 1k tbc Stream #0.1: Audio: nellymoser, 44100 Hz, mono, s16 [libx264 @ 0x13518b0]using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE 4.2 [libx264 @ 0x13518b0]profile Baseline, level 4.2 Output #0, ipod, to 'd:\temp\out.m4v': Stream #0.0: Video: libx264, yuv420p, 320x240, q=2-31, 200 kb/s, 1k tbn, 1k tbc Stream #0.1: Audio: libfaac, 22050 Hz, mono, s16, 128 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding frame= 90 fps= 0 q=-1.0 Lsize= 128kB time=6.87 bitrate= 152.4kbits/s video:92kB audio:32kB global headers:1kB muxing overhead 2.620892% [libx264 @ 0x13518b0]slice I:8 Avg QP:29.62 size: 7047 [libx264 @ 0x13518b0]slice P:82 Avg QP:30.83 size: 467 [libx264 @ 0x13518b0]mb I I16..4: 17.9% 0.0% 82.1% [libx264 @ 0x13518b0]mb P I16..4: 0.6% 0.0% 0.0% P16..4: 23.1% 0.0% 0.0% 0.0% 0.0% skip:76.3% [libx264 @ 0x13518b0]final ratefactor: 57.50 [libx264 @ 0x13518b0]SSIM Mean Y:0.9544735 [libx264 @ 0x13518b0]kb/s:8412.6 My suspicion is that it has something to do with the audio encoding. If so, does anyone know how to force it to reencode the audio to the proper format? Any other ideas?

    Read the article

  • How can I get the new Facebook Javascript SDK to work in IE8?

    - by archbishop
    I've boiled down my page to the simplest possible thing, and it still doesn't work in IE8. Here's the entire html page: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" xmlns:fb="http://www.facebook.com/2008/fbml" xml:lang="en" lang="en"> <head></head> <body> <div id="fb-root"></div> <fb:login-button></fb:login-button> <script src="http://connect.facebook.net/en_US/all.js"></script> <script> FB.init({appId: 'd663755ef4dd07c246e047ea97b44d6a', status: true, cookie: true, xfbml: true}); FB.Event.subscribe('auth.sessionChange', function(response) { alert(JSON.stringify(response)); }); FB.getLoginStatus(function (response) { alert(JSON.stringify(response)); }); </script> </body> </html> In firefox, safari, and chrome (on a mac), I get the behavior I expect: if I am not logged into Facebook, I get a dialog on page load with an empty session. When I click the Login button and log in, I get a second dialog with a session. If I am logged into Facebook, I get two dialogs with sessions: one from the getLoginStatus call, and another from the event. In IE8, I get no dialogs when I load the page. The getLoginStatus callback is not invoked. When I click the Login button, I get a dialog, but it has a very strange error in it: Invalid Argument The Facebook Connect cross-domain receiver URL (http://static.ak.fbcdn.net/connect/xd_proxy.php#?=&cb=f3e91da434653f2&origin=http%3A%2F%2Fsword.sqprod.com%2Ff210cba91f2a6d4&relation=opener&transport=flash&frame=f27aa957225164&result=xxRESULTTOKENxx) must have the application's Connect URL (http://mysiteurl.com/) as a prefix. You can configure the Connect URL in the Application Settings Editor. I've sanitized the Connect URL above, but it is correct. The dialog does have username/password fields. If I log in, the dialog box gets redirected to my Connect URL, but there's no fb cookie, so of course nothing works. What am I doing wrong here?

    Read the article

  • Asyncronus javascript rendering widgets

    - by Joe J
    Hey all, I'm creating a javascript widget so third partys (web designers) can post a link on their website and it will render the widget on their site. Currently, I'm doing this with just a script link tag: <div class="some_random_div_in_html_body"> <script type='text/javascript' src='http://remotehost.com/link/to/widget.js'></script> </div> However, this has the side-effect of slowing down a thrid party's website render times of the page if my site is under a load. Therefore, I'd like the third party website to request the widget link from my site asyncronously and then render it on their site when the widget link loads completely. The Google Analytics javascript snippet seems to have a nice bit of asyncronous code that does a nice async request to model off of, but I'm wondering if I can modify it so that it will render content on the third party's site. Using the example below, I want the content of http://mysite.com/link/to/widget.js to render something in the "message" id field. <HTML> <HEAD><TITLE>Third Party Site</TITLE><STYLE>#message { background-color: #eee; } </STYLE></HEAD> <BODY> <div id="message">asdf</div> <script type="text/javascript"> (function() { var ga = document.createElement('script'); ga.type = 'text/javascript'; ga.async = true; ga.src = 'http://mysite.com/link/to/widget.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(ga, s); })(); </script> </BODY> </HTML> I don't know if what I'm trying to do constitutes Cross Site Scripting (still a bit vague on that concept) but am wondering if what I'm trying to do is possible. Or if anyone has any other approaches to creating javascript widgets effectively, I'd appreciate any advice. Thanks for reading this. Joe

    Read the article

  • Server side Xforms form validation and integration into ASP.NET

    - by Nigel
    I have recently been investigating methods of creating web-based forms for an ASP.NET web application that can be edited and managed at runtime. For example an administrator might wish to add a new validation rule or a new set of fields. The holy grail would provide a means of specifying a form along with (potentially very complex) arbitrary validation rules, and allocation of data sources for each field. The specification would then be used to update the deployed form in the web application which would then validate submissions both on the client side and on the server side. My investigations led me to Xforms and a number of technologies that support it. One solution appears to be IBM Lotus Forms, but this requires a very large investment in terms of infrastructure, which makes it infeasible, although the forms designer may be useful as a stand-alone tool for creating the forms. I have also discounted browser plug-ins as the form must be publicly visible and cross-browser compliant. I have noticed that there are numerous javascript libraries that provide client side implementations given an Xforms schema. These would provide a partial solution but server side validation is still a requirement. Another option seems to involve the use of server side solutions such as the Java application Orbeon. Orbeon provides a tool for specifying the forms (although not as rich as Lotus Forms Designer), but the most interesting point is that it can translate an XForms schema into an XHTML form complete with validation. The fact that it is written in Java is not a big problem if it is possible to integrate with the existing ASP.NET application. So my question is whether anyone has done this before. It sounds like a problem that should have been solved but is inherently very complex. It seems possible to use an off-the-shelf tool to design the form and export it to an Xforms schema and xhtml form, and it seems possible to take that xforms schema and form and publish it using a client side library. What seems to be difficult is providing a means of validating the form submission on the server side and integrating the process nicely with .NET (although it seems the .NET community doesn't involve themselves with XForms; please correct me if I'm wrong on this count). I would be more than happy if a product provided something simple like a web service that could validate a submission against a schema. Maybe Orbeon does this but I'd be grateful if somebody in the know could point me in the right direction before I research it further. Many thanks.

    Read the article

  • What IDE to use for Python

    - by husayt
    As a Python newbie, it is interesting to know what IDE's ("GUIs/editors") others use for Python coding. If you can just give the name (e.g. Textpad, Eclipse ..) that will be enough. If it is already mentioned, you can just vote for it. But if you can also give some more comparative information, that will be much appreciated. Thanks. Update: Results so far PyDev with Eclipse (CP, F, AC, PD, EM, SI, MLS, UML, SC, UT, LN, CF, BM) Komodo (CP, C/F, MLS, PD, AC, SC, SI, BM, LN, CF, CT) Emacs (CP, F, AC, MLS, PD, EM, SC, SI, BM, LN, CF, CT, UT, UML) Vim (CP, F, AC, MLS, SI, BM, LN, CF ) TextMate (Mac, CT, CF, MLS, SI, BM, LN) Gedit (Linux, F, AC, MLS, BM, LN, CT [sort of]) Idle (CP, F, AC) PIDA (Linux, CP, F, AC, MLS, SI, BM, LN, CF)(VIM Based) NotePad++ (Windows) BlueFish (Linux) JEdit (CP, F, BM, LN, CF, MLS) E-Texteditor (TextMate Clone for Windows) WingIde (CP, C, AC, MLS (support for C), PD, EM, SC, SI, BM, LN, CF, CT, UT) Eric Ide (CP, F, AC, PD, EM, SI, LN, CF, UT) Pyscripter (Windows, F, AC, PD, EM, SI, LN, CT, UT) ConTEXT (Windows, C) SPE (F, AC, UML) SciTE (CP, F, MLS, EM, BM, LN, CF, CT, SH) Zeus (W, C, BM, LN, CF, SI, SC, CT) NetBeans (CP, F, PD, UML, AC, MLS, SC, SI, BM, LN, CF, CT, UT, RAD) DABO (CP) BlackAdder (C, CP, CF, SI) PythonWin (W, F, AC, PD, SI, BM, CF) Geany (CP, F, very limited AC, MLS, SI, BM, LN, CF) UliPad (CP, F, AC, PD, MLS, SI, LI, CT, UT, BM) Boa Constructor (CP, F, AC, PD, EM, SI, BM, LN, UML, CF, CT) ScriptDev (W, C, AC, MLS, PD, EM, SI, BM, LN, CF, CT) Spider (CP, F, AC) Editra (CP, F, AC, MLS, SC, SI, BM, LN, CF) Pfaide (Windows, C, AC, MLS, SI, BM, LN, CF, CT) KDevelop (CP, F, MLS, SC, SI, BM, LN, CF) Acronyms used: CP - Cross Platfom C - Commercial F - Free AC - Automatic Code-completion MLS - Multi-Language Support PD - Integrated Python Debugging EM - ErrorMarkup SC - Source Control integration SI - Smart Indent BM - Bracket Matching LN - Line Numbering UML - UML editing / viewing CF - Code Folding CT - Code Templates UT - Unit Testing UID - Gui Designer (e.g. QT, Eric, ..) DB - integrated database support RAD - Rapid app development support I don't mention basics like Syntax highlighting as I expect these by default. This is a just dry list reflecting your feedback and comments, I am not advocating any of these tools. I will keep updating this list as you keep posting your answers. PS. Can you help me to add features of the above editors to the list (like autocomplete, debugging, or etc)?

    Read the article

  • WebClient security error when accessing the world of warcraft armoury

    - by user348446
    Hello World, I am trying to piece together a solution to a problem. Basically I am using Silverlight 4 with C# 4.0 to access the world of warcraft armoury. If anyone has done this - please oh please provide the working .net 4.0 code. The code I am attempting to run is (e.Error contains a securtiy error): private void button10_Click(object sender, RoutedEventArgs e) { string url = @"http://eu.wowarmory.com/guild-info.xml?r=Eonar&n=Gifted and Talented"; WebClient wc = new WebClient(); // HOW DO I ADD A USER AGENT STRING (RESPONSE MAY VARY (I.E. HTML VS XML) IF PAGE THINKS CALL IS NOT CAPABABLE OF SUPPORTING XML TRANSFORMATIONS) //wc.ResponseHeaders["User-Agent"] = "Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.0)"; wc.DownloadStringCompleted += new DownloadStringCompletedEventHandler(wc_DownloadStringCompleted); wc.DownloadStringAsync(new Uri(url)); } void wc_DownloadStringCompleted(object sender, DownloadStringCompletedEventArgs e) { if (e.Error == null) { string result = e.Result; XDocument ArmouryXML = XDocument.Parse(result); ShowGuildies(ArmouryXML); } else { MessageBox.Show("Something is complaining about security but not sure what!"); } } Notes: C# 4.0 The armoury is an XML file - but i believe it reverts to html should the request not be from a browser that supports XML transformation. But i don't think I am getting this far. The armoury has a cross domain policy file on it - this may be the cause of the error (not sure! I have uploaded to a production server I am testing it locally using IIS website I am going insane! Websites have made the suggestion that this problem can be overcome by creating a WebProxy - but I haven't the first clue how to do this. It would be great if someone could take on this challenge and show us all that it is possible. I'd prefer a non-proxy solution first, then try a proxy. The error details: e.Error = {System.Security.SecurityException --- System.Security.SecurityException: Security error. at System.Net.Browser.BrowserHttpWebRequest.InternalEndGetResponse(IAsyncResult asyncResult) at System.Net.Browser.BrowserHttpWebRequest.<c__DisplayClass5. Any intelligent master coders out there who can solve this in their sleep? Thanks if you can! Pass this on to someone who can if you can't. If you know someone who can't, don't pass it to them, but if you know someone can't then presumedly you know how to solve it and would encourage you to give it a go! Cheers! Dan.

    Read the article

  • XNA - Keyboard text input

    - by Sekhat
    Okay, so basically I want to be able to retrieve keyboard text. Like entering text into a text field or something. I'm only writing my game for windows. I've disregarded using Guide.BeginShowKeyboardInput because it breaks the feel of a self contained game, and the fact that the Guide always shows XBOX buttons doesn't seem right to me either. Yes it's the easiest way, but I don't like it. Next I tried using System.Windows.Forms.NativeWindow. I created a class that inherited from it, and passed it the Games window handle, implemented the WndProc function to catch WM_CHAR (or WM_KEYDOWN) though the WndProc got called for other messages, WM_CHAR and WM_KEYDOWN never did. So I had to abandon that idea, and besides, I was also referencing the whole of Windows forms, which meant unnecessary memory footprint bloat. So my last idea was to create a Thread level, low level keyboard hook. This has been the most successful so far. I get WM_KEYDOWN message, (not tried WM_CHAR yet) translate the virtual keycode with Win32 funcation MapVirtualKey to a char. And I get my text! (I'm just printing with Debug.Write at the moment) A couple problems though. It's as if I have caps lock on, and an unresponsive shift key. (Of course it's not however, it's just that there is only one Virtual Key Code per key, so translating it only has one output) and it adds overhead as it attaches itself to the Windows Hook List and isn't as fast as I'd like it to be, but the slowness could be more due to Debug.Write. Has anyone else approached this and solved it, without having to resort to an on screen keyboard? or does anyone have further ideas for me to try? thanks in advance. note: This is cross posted from the XNA Creators Forums, so if I get an answer there I'll post it here and Vice-Versa Question asked by Jimmy Maybe I'm not understanding the question, but why can't you use the XNA Keyboard and KeyboardState classes? My comment: It's because though you can read keystates, you can't get access to typed text as and how it is typed by the user. So let me further clarify. I want to implement being able to read text input from the user as if they are typing into textbox is windows. The keyboard and KeyboardState class get states of all keys, but I'd have to map each key and combination to it's character representation. This falls over when the user doesn't use the same keyboard language as I do especially with symbols (my double quotes is shift + 2, while american keyboards have theirs somewhere near the return key).

    Read the article

  • Android stream to Wowza

    - by Curtis Kiu
    I feel very confused about Android streaming to wowza. I am doing a video conference using rtmp cross-platform, but Android doesn't eat RTMP. Therefore I need to find another way to do it. Upstreaming I found a new open-source app called spydroid-ipcamera. It is using rtp, sending udp packets to computer, and opens it in vlc using the following sdp v=0 s=Unnamed m=video 5006 RTP/AVP 96 a=rtpmap:96 H264/90000 a=fmtp:96 packetization-mode=1;profile-level-id=420016;sprop-parameter-sets=Z0IAFukBQHsg,aM4BDyA=; But it can't work. Then I follow wowza tutorial and stream to it and then play again in VLC. That works! I wrote it in http://code.google.com/p/spydroid-ipcamera/issues/detail?id=2 However when I want to add audio in the packet, it fails to work. I change to code in http://code.google.com/p/spydroid-ipcamera/source/browse/trunk/src/net/mkp/spydroid/CameraStreamer.java mr.setAudioSource(MediaRecorder.AudioSource.MIC); mr.setVideoSource(MediaRecorder.VideoSource.CAMERA); mr.setOutputFormat(MediaRecorder.OutputFormat.MPEG_4); mr.setVideoFrameRate(20); mr.setVideoSize(640, 480); mr.setAudioEncoder(MediaRecorder.AudioEncoder.AAC); mr.setVideoEncoder(MediaRecorder.VideoEncoder.H264); mr.setPreviewDisplay(holder.getSurface()); Then I thought that the problem should be in sdp, but I don't know how to due with sdp. I am streaming H.264/AAC with Mp4 Second I don't understand sdp. So how can I make video conference upstreaming part using this apps. Android ----(UDP Port:5006)----> PC (SDP file) and then Wowza read the SDP file ------> VLC I think in this way the system cannot handle more than 1 client. sdp can only hold 1 port, any idea or actually it wont' work? Also Wowza need to set the stream before we stream it, so does it mean that I should not follow this way to do it? Sorry my English is poor, I hope you guys understand.

    Read the article

  • Oracle 9i Session Disconnections

    - by mlaverd
    [Cross-Posting from ServerFault] I am in a development environment, and our test Oracle 9i server has been misbehaving for a few days now. What happens is that we have our JDBC connections disconnecting after a few successful connections. We got this box set up by our IT department and handed over to. It is 'our problem', so options like 'ask you DBA' isn't going to help me. :( Our server is set up with 3 plain databases (one is the main dev db, the other is the 'experimental' dev db). We use the Oracle 10 ojdbc14.jar thin JDBC driver (because of some bug in the version 9 of the driver). We're using Hibernate to talk to the DB. The only thing that I can see that changed is that we now have more users connecting to the server. Instead of one developer, we now have 3. With the Hibernate connection pools, I'm thinking that maybe we're hitting some limit? Anyone has any idea what's going on? Here's the stack trace on the client: Caused by: org.hibernate.exception.GenericJDBCException: could not execute query at org.hibernate.exception.SQLStateConverter.handledNonSpecificException(SQLStateConverter.java:126) [hibernate3.jar:na] at org.hibernate.exception.SQLStateConverter.convert(SQLStateConverter.java:114) [hibernate3.jar:na] at org.hibernate.exception.JDBCExceptionHelper.convert(JDBCExceptionHelper.java:66) [hibernate3.jar:na] at org.hibernate.loader.Loader.doList(Loader.java:2235) [hibernate3.jar:na] at org.hibernate.loader.Loader.listIgnoreQueryCache(Loader.java:2129) [hibernate3.jar:na] at org.hibernate.loader.Loader.list(Loader.java:2124) [hibernate3.jar:na] at org.hibernate.loader.hql.QueryLoader.list(QueryLoader.java:401) [hibernate3.jar:na] at org.hibernate.hql.ast.QueryTranslatorImpl.list(QueryTranslatorImpl.java:363) [hibernate3.jar:na] at org.hibernate.engine.query.HQLQueryPlan.performList(HQLQueryPlan.java:196) [hibernate3.jar:na] at org.hibernate.impl.SessionImpl.list(SessionImpl.java:1149) [hibernate3.jar:na] at org.hibernate.impl.QueryImpl.list(QueryImpl.java:102) [hibernate3.jar:na] ... Caused by: java.sql.SQLException: Io exception: Connection reset at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:112) [ojdbc14.jar:Oracle JDBC Driver version - "10.2.0.4.0"] at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:146) [ojdbc14.jar:Oracle JDBC Driver version - "10.2.0.4.0"] at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:255) [ojdbc14.jar:Oracle JDBC Driver version - "10.2.0.4.0"] at oracle.jdbc.driver.T4CPreparedStatement.executeForDescribe(T4CPreparedStatement.java:829) [ojdbc14.jar:Oracle JDBC Driver version - "10.2.0.4.0"] at oracle.jdbc.driver.OracleStatement.executeMaybeDescribe(OracleStatement.java:1049) [ojdbc14.jar:Oracle JDBC Driver version - "10.2.0.4.0"] at oracle.jdbc.driver.T4CPreparedStatement.executeMaybeDescribe(T4CPreparedStatement.java:854) [ojdbc14.jar:Oracle JDBC Driver version - "10.2.0.4.0"] at oracle.jdbc.driver.OracleStatement.doExecuteWithTimeout(OracleStatement.java:1154) [ojdbc14.jar:Oracle JDBC Driver version - "10.2.0.4.0"] at oracle.jdbc.driver.OraclePreparedStatement.executeInternal(OraclePreparedStatement.java:3370) [ojdbc14.jar:Oracle JDBC Driver version - "10.2.0.4.0"] at oracle.jdbc.driver.OraclePreparedStatement.executeQuery(OraclePreparedStatement.java:3415) [ojdbc14.jar:Oracle JDBC Driver version - "10.2.0.4.0"] at org.hibernate.jdbc.AbstractBatcher.getResultSet(AbstractBatcher.java:208) [hibernate3.jar:na] at org.hibernate.loader.Loader.getResultSet(Loader.java:1812) [hibernate3.jar:na] at org.hibernate.loader.Loader.doQuery(Loader.java:697) [hibernate3.jar:na] at org.hibernate.loader.Loader.doQueryAndInitializeNonLazyCollections(Loader.java:259) [hibernate3.jar:na] at org.hibernate.loader.Loader.doList(Loader.java:2232) [hibernate3.jar:na]

    Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >