Search Results

Search found 4217 results on 169 pages for 'central administration'.

Page 134/169 | < Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >

  • Changing IP address in IIS for SharePoint site results in Directory listing error

    - by Dan
    I have a server here that has 2 roles. One is Exchange 2007 and the other is MOSS 2007. In IIS i have a site, go.domain.com which has our OWA. The other is internal.domain.com which is the MOSS site. I have given the NIC local IPs and each site is using host headers. The GO site has an SSL cert from NetSol, and the MOSS site has a self signed. Right now going to either shows the NetSol site, which browsers complain about when going to the internal.domain.com site, obviously, since they are on the same IP in IIS. Both sites have always run off the original IP of 10.0.0.3 in IIS. When i added the second IP to the NIC, (10.0.0.6) and changed the Sharepoint site in IIS to use this for http and https access, I now get this message in a browser when trying to connect. Directory Listing Denied This Virtual Directory does not allow contents to be listed. Changing the IP back to 10.0.0.3 and the internal site is back up. What am I missing here? Do i need to fool around with Alternate Access Mappings in Central Admin? Am i completely missing the point with multiple SSL certs and host headers?

    Read the article

  • Remote Desktop Session Black after Minimize

    - by TorgoGuy
    PROBLEM: When I minimize a remote desktop session and restore it, the remote desktop screen shows up black. This only happens when connecting to a particular computer. DETAILS: If I start clicking around in the black area, portions of the screen will start redrawing and showing up correctly. For example, if I leave a window open in the remote session and click where that window is located on the remote computer, then that window--and only that window--will redraw, and sometimes a portion of that window won't redraw (usually the toolbar). And to clarify--the window only has to be minimized momentarily, so it doesn't seem to be a timeout issue. Clicking or typing in the remote session still causes the remote computer to respond appropriately. Disconnecting from the session and reconnecting restores the whole screen image, as does clicking all over the place in the black image (causing each section to redraw). CONFIGURATION: This problem only happens for me when connecting to a particular computer (a W2K Server box configured to allow remote administration) and only with certain client computers. I've tried 7 different client computers with various versions of Remote Desktop (the OSes were: Win2K, Server 2003, Server 2008, Windows 7 RC, 3 XP) and two of them exhibit the problem (one is one of the XP boxes and the other is Windows 7). Those same computers can RDP to other computers without problem. RESOLUTION ATTEMPTS: I have tried the following: Disable the LOCAL screen saver as mentioned on Technet Turned off bitmap caching in the client, as mentioned on many forums. Updated to version 6.1 of the remote desktop client Using mRemote (I doubted this would work since it uses MS's code for connecting to RDP servers) Turning off all video acceleration. QUESTION: Any ideas on what is causing this?

    Read the article

  • Sharing disk volumes across OpenVZ guests to reduce Package Management Overhead

    - by andyortlieb
    Is it feasible to create a single "master" OpenVZ guest who would only be used for package management, and use something like mount --bind on several other OpenVZ guests sort of trick them into using the environment installed by the master guest? The point of this would be so that users can maintain their own containers, and yet stay in sync with the master development environment, so they'll always have the latest & greatest requirements without worrying too much about system administration. If they need to install their own packages, could put them in /opt, or /usr/local (or set a path to their home directory)? To rephrase, I would like several (developer's, for example) OpenVZ guests whose /bin, /usr (and so on...) actually refer to the same disk location as that of a master OpenVZ guest who can be started up to install and update common packages for the environment to be shared by all of this group of OpenVZ guests. For what it's worth, we're running Debian 6. Edit: I have tried mounting (bind, and readonly) /bin, /lib, /sbin, /usr in this fashion and it refuses to start the containers stating that files are already mounted or otherwise in use: Starting container ... vzquota : (error) Quota on syscall for id 1102: Device or resource busy vzquota : (error) Possible reasons: vzquota : (error) - Container's root is already mounted vzquota : (error) - there are opened files inside Container's private area vzquota : (error) - your current working directory is inside Container's vzquota : (error) private area vzquota : (error) Currently used file(s): /var/lib/vz/private/1102/sbin /var/lib/vz/private/1102/usr /var/lib/vz/private/1102/lib /var/lib/vz/private/1102/bin vzquota on failed [3] If I unmount these four volumes, and start the guest, and then mount them after the guest has started, the guest never sees them mounted.

    Read the article

  • Why does my Internet slow to a crawl unless I reboot my router every few days?

    - by Lord Torgamus
    A few weeks ago, I noticed that my Internet connection had slowed down to a crawl. I waited a few days hoping it would go away on its own, but it didn't get better. So I asked this question about how to make it faster. The problem went away after I updated to the latest firmware, so I didn't follow up too carefully. But every few days since then, my Internet has slowed down again. Unlike before, all I have to do to fix it is open the router administration page and press the "Reboot" button. Nothing else seems to work, though I'm sure there are options I haven't tried. If it makes a difference, my girlfriend and I both transfer large amounts of data fairly routinely for school (videoconferencing, downloading entire recorded lectures). The router is a Cisco/Linksys 160N V3 that's about a year old. Most of the time, it deals with just two standard Windows 7 laptops. The only thing I came across while searching for answers/dupes was this question, which seems similar superficially, but probably doesn't have the same root issue. Anyways, it's not resolved. What could be causing these slowdowns, and how can I get rid of them?

    Read the article

  • duplicity fail: not promping for password: "Running 'sftp user@host' failed"

    - by Thr4wn
    I have two linode VPS accounts and I want to back up one onto the other (the reasons are mainly for fun and to practice server administration.) the short version Duplicity isn't even asking for my password, but immediately says "invalid SSH password" (but I can ssh into the other server). why? the long version When I run duplicity /home/me scp://[email protected]//root/backup I get Invalid SSH password Running 'sftp [email protected]' failed (attempt #1) Invalid SSH password Running 'sftp [email protected]' failed (attempt #2) Invalid SSH password Running 'sftp [email protected]' failed (attempt #3) And it says Invalid SSH password immediately with no opportunity for me to actually type the password. When I type duplicity full -v9 --num-retries 4 /home/me scp://[email protected]//root/backup I get Main action: full Running 'sftp [email protected]' (attempt #1) State = sftp, Before = 'Connecting to 97.107.129.67... [email protected]'s' State = sftp, Before = '' Invalid SSH password Running 'sftp [email protected]' failed (attempt #1) I can ssh into [email protected] fine, and in fact have the ip in known_hosts before I tried any of this. serer 1 (from which I'm running the duplicity command) is Linode's default Ubuntu 8 setup with only a handful of programs installed via apt-get. server 2 (represented by x.x.x.x) is literally only Linode's default Ubuntu 8 setup I previously tried using SystemImager -- would that have changed settings in a destructive way? (I have removed and rebooted since then) Isn't Duplicity supposed to prompt for password? Am I using it wrong? are there common mistakes/dependencies I need to know about? Is there any way that x.x.x.x could be setup that could make this not work (I used Linode's default Ubuntu 8 setup and barely )?

    Read the article

  • MOSS2007 tries to use ActiveDirectory when I have configured an alternative membership provider

    - by glenatron
    I've got a MOSS site that I am trying to configure using Forms authentication and absolutely any kind of membership provider whatsoever. Thus far ActiveDirectory has proved obstructively difficult so I've just whipped up a simple stub membership provider and put it in the GAC. It's a very basic and simple provider but it works fine with an ASP.Net site, I just can't make it work with Sharepoint. On Sharepoint I get the following error when I look for StubProvider:Bob ( or anything else for that matter) from the "Policy For Web Application" people picker: Error in searching user 'StubProvider:bob' : System.ComponentModel.Win32Exception: Unable to contact the global catalog server at Microsoft.SharePoint.Utilities.SPActiveDirectoryDomain.GetDirectorySearcher() at Microsoft.SharePoint.WebControls.PeopleEditor.SearchFromGC(SPActiveDirectoryDomain domain, String strFilter, String[] rgstrProp, Int32 nTimeout, Int32 nSizeLimit, SPUserCollection spUsers, ArrayList& rgResults) at Microsoft.SharePoint.Utilities.SPUserUtility.SearchAgainstAD(String input, SPActiveDirectoryDomain domainController, SPPrincipalType scopes, SPUserCollection usersContainer, Int32 maxCount, String customQuery, TimeSpan searchTimeout, Boolean& reachMaxCount) at Microsoft.SharePoint.Utilities.SPActiveDirectoryPrincipalResolver.SearchPrincipals(String input, SPPrincipalType scopes, SPPrincipalSource sources, SPUserCollection usersContainer, Int32 maxCount, Boolean& reachMaxCount) at Microsoft.SharePoint.Utilities.SPUtility.SearchPrincipalFromResolvers(List`1 resolvers, String input, SPPrincipalType scopes, SPPrincipalSource sources, SPUserCollection usersContainer, Int32 maxCount, Boolean& reachMaxCount, Dictionary`2 usersDict). The Provider is named as Authentication Provider for the Site Collection in question. As far as I can tell this is because Sharepoint is still trying to access ActiveDirectory rather than talking to the provider I'm asking it to use. My Sharepoint Central Administration section includes this: <membership> <providers> <add name="StubProvider" type="StubMembershipProvider.Provider, StubMembershipProvider, Version=1.0.0.0, Culture=neutral, PublicKeyToken=5bd7e2498c3e1a03" /> </providers> </membership> And also: <PeoplePickerWildcards> <clear /> <add key="StubProvider" value="%" /> </PeoplePickerWildcards> Is there a clear reason why this would not be accessible from the PeoplePicker or why it is still trying to use ActiveDirectory? I've made sure I reset IIS and even restarted the server to see if either of those helped but they made no difference.

    Read the article

  • Setting up Windows SBS 2008 network on Xen

    - by samyboy
    I'm trying to install a Windows SBS 2008 server in a Xen environment. The OS is booting fine. Unfortunately I can't figure out how to set up the network settings. Dom0 is a Debian Lenny hosting around 10 virtual servers. Here are the settings I'm using in the hosted Windows SBS: IP address: 10.20.0.8 Network mask: 255.255.0.0 Gateway: 10.20.0.1 Note that during the installation stage, Windows set the net mask at 255.255.255.0 without letting me choose. Gross. Windows SBS tells me I have a "limited connection". I can't ping the gateway nor any other IP except localhost and it's own IP (10.20.0.8). Here is the Xen config file: kernel = '/usr/lib/xen-3.2-1/boot/hvmloader' builder = 'hvm' memory = '4096' device_model='/usr/lib/xen-3.2-1/bin/qemu-dm' acpi=1 apic=1 pae=1 vcpus=1 name = 'winexchange' # Disks disk = [ 'phy:/dev/wnghosts/exchange-disk,ioemu:hda,w', 'file:/mnt/freespace/ISO/DVD1_Installation.iso,ioemu:hdc:cdrom,r' ] # Networking vif = [ 'mac=00:16:3E:0A:D0:1B, type=ioemu, bridge=xenbr0'] # video stdvga=0 serial='pty' ne2000=0 # Behaviour boot='c' sdl=0 # VNC vfb = [ 'type=vnc' ] vnc=1 vncdisplay=1 vncunused=1 usbdevice='tablet' This config is working with others Windows XP domU's. I tried to change the ne2000 values with 0 and 1 with no effect. I am far from having good Windows administration skills so I guess I definitely need some help on this case. Thanks.

    Read the article

  • nginx not serving admin static files?

    - by toto_tico
    First, I want to clarify that this error is just for the admin static files. This means my problem is specific just to the static files that corresponds to the Django admin. The rest of the static files are working perfect. Basically my problem is that for some reason I cannot access those admin static files with the ngix server. It works perfect with the micro server of Django and the collect static is doing its job. This means it is putting the files on the expected place in the static folder. The urls are correct but I cannot even access the admin static files directly, but the others I can. So, for example, I am able to access this url (copying it in the browser): myserver.com:8080/static/css/base/base.css but i am not able to access this other url (copying it in the browser): myserver.com:8080/static/admin/css/admin.css I also tried to copy the admin/ directory structure into other_admin_directory_name/. Then I can access myserver.com:8080/static/other_admin_directory_name/css/admin.css Then, it works. So, I checked permissions and everything is fine. I tried to change ADMIN_MEDIA_PREFIX = '/static/admin/' to ADMIN_MEDIA_PREFIX = '/static/other_admin_directory_name/', it doesn't work. This a mistery in itself that I am exploring but still no luck. Finally, and it seems to be an important clue: I tried to copy the admin/ directory structure into admin_and_then_any_suffix/. Then I cannot access myserver.com:8080/static/admin_and_then_any_suffix//css/admin.css So, if the name of the directory starts with admin (for example administration or admin2) it doesn't work. * added thanks to sarnold observation ** the problem seems to be in the nginx configuration file /etc/nginx/sites-available/mysite location /static/admin { alias /home/vl3/.virtualenvs/vl3/lib/python2.7/site-packages/django/contrib/admin/media/; }

    Read the article

  • Security and data backup for Ubuntu usb installation

    - by AMS949
    Due to encryption on my corporate laptop I opted to install Ubuntu 9.10 on a flash drive and just use it as my hard drive. I tried the vmware but it crashed my xp a couple of times. Now I have a couple of concerns since I am totally new to Ubuntu and Linux. First, would it be possible for me to transfer my installation to a new usb drive? I now have a 4gb and it may get filled up soon, I don't seem to be able to see my actual files when I browse the usb drive. I also tried copying all files from this usb to another and boot from it but that failed. Second, whenever the system boots up I am never prompted for a password, it is always the username ubuntu. Which I guess means if I lose my usb drive my data is open wide. Is there a way to secure it or to use users and groups as on a regular hard drive installation? As a background, I created this by going into a working Ubuntu installation, System - Administration - USB Starter Disk Creator (was that the right way to start with?) Thanks!

    Read the article

  • Cooling Server Closet - No A/C Is Possible

    - by JamesCo
    We're moving into a new office in an old building in London (that's England :) and are walling off a 2m x 1.3m area where the router & telephone equipment currently terminates to use as a server closet. The closet will contain: 2 24-port switches 1 router 1 VSDL modem 1 Dell desktop 1 4-bay NAS 1 HP micro-server 1 UPS Miscellaneous minor telephony boxes. There is no central A/C in the office and there never will be. We can install ducting to the outside quite easily - it's only a couple of metres to the windows, which face a courtyard. My question is whether installing an extractor fan with ducting to the window should be sufficient for cooling? Would an intake fan and intake duct (from the window, too) be required? We don't want to leave a gap in the closet door as that'll let noise out into the office. If we don't have to put a portable A/C unit into the closet, that'd be perfect. The office has about 12 people; London is temperate, average maximum in August is 31 Celsius, 25 Celsius is more typical. The same equipment runs fine in our current office (same building as new office, also no A/C) but it isn't in an enclosed space. I can see us putting say one Dell 2950 tower server into the closet, but no more than that. So, sustained power consumption in the closet would currently be about 800w (I'm guessing); possibly in the future 2kw. The closet will have a ceiling and no windows and be well-insulated. We don't care if the equipment runs hot, so long as it runs and we don't hear it.

    Read the article

  • Is there a small business router that shows bandwidth usage graphs in the admin panel?

    - by Robert Drake
    I support a large number of public libraries that are having their networks upgraded in response to a grant application. These libraries are generally home to between 6-15 computers and have little or no tech services either onsite or contracted remotely. In order to justify current and future purchases, a number of the libraries have requested routers that can provide bandwidth usage graphs that they can show to their managing boards. Is there a small business router that displays traffic graphs in the router administration web interface? The router needs to suppport DHCP and basic firewalling. No other features are required. Further, the reports just need to show overall trends. It is not necessary to show traffic by IP, by protocol/application, or by time of day. They just need an overall week to week, month to month, trend line. I'm familiar with MRTG/PRTG/tools that collect SNMP data from the router, but the libraries don't have the expertise for the configuration. I've considered installing the tomato firmware on some cheap home/home office routers, but if there's a commercial product that can be purchased that would be significantly simpler. Also the library boards would be much more likely to approve the purchase of a commercial product over a 'hacked' one. Any assistance would be appreciated.

    Read the article

  • Zabbix Proxy not collecting data

    - by syntaxcollector
    Hi All I have a working Zabbix 1.8.2 server collecting data for our office and our colo facility. However the link between the colo and office is flaky. What I'm trying to do is setup a proxy on the colo side to have a 1 hour cache and relay the data to our primary server at the office. Our zabbix server is compiled from source and uses a mysql database I've followed the instructions found in the zabbix documentation to compile the proxy using a sqlite3 database. I add the proxy to zabbix under Administration-DM-Proxies. The zabbix server "sees" the proxy because the "last seen" field is always under 60s. However when I assign a colo host to the proxy I stop receiving data from it. The colo host's zabbix_agentd.log file says this: 29343:20100622:124847 Timeout while answering request 29343:20100622:124847 Getting list of active checks failed. Will retry after 60 seconds The zabbix_proxy.log says this. 2041:20100622:123131.760 Deleted 0 records from history [0.000994 seconds] 2028:20100622:124131.671 Error while receiving answer from server [ZBX_TCP_READ() failed I also am unable to receive any SNMP data which is more important to me than the zabbix agent data. Has anyone had this problem before? Zabbix Server OS: CentOS5.4 Zabbix Server Build: 1.8.2 from source Zabbix Proxy OS: CentOS5.4 Zabbix Proxy Build: 1.8.2 from source P.S. The SQLite database on the zabbix proxy never gets any data written to it, it is identical to when I created it from the blank schema in zabbix-1.8.2/create/schema. (Yes I've checked the permissions)

    Read the article

  • Cisco VPN endpoints disconnecting from a VLAN

    - by dunxd
    I have a number of Cisco ASA 5505 and PIX 506e around the world acting as VPN endpoints. They connect to a Cisco VPN Concentrator 3000 at HQ. I am using EZVPN to set up the VPN (i.e. most of the config is central on the VPN Concentrator) The majority of endpoints work absolutely fine. However, there are three that do not. 2 ASAs and 1 PIX get disconnected from one of the VLANs on our network. This is the VLAN that my monitoring server runs on - so those endpoints look as if they have gone down. However, I can still ping the endpoints from our user VLAN. If I then SSH onto the endpoint, and do a ping to my monitoring server, the connection comes back. Then after about 10 minutes it stops working again. I've looked at the configuration of my endpoints, and I can't see any significant differences. One common feature is that the affected endpoints are connecting to the internet via retail quality routers. However, I don't see how this could affect traffic within a VPN tunnel. Any ideas or suggestions? I've also got a thread on Cisco's forums at https://supportforums.cisco.com/thread/344638. One other person has reported the same problem.

    Read the article

  • Nexus functionality is limited after installation

    - by Dmitriy Sukharev
    I have a CentOS based server with Sonatype Nexus 2.0.4-1 installed. The issue is that there are no standard "Artifact Search", "Advanced Search", "Browse Index", "Refresh Index" Nexus features, as well as Artifact Information tab after selection of any artifact (only Maven Information tab). I tried to Google, but was amazed that there're no information about this issue. Actually it looks like all actions I've done are: wget http://www.sonatype.org/downloads/nexus-2.0.4-1-bundle.tar.gz tar -xvf nexus-2.0.4-1-bundle.tar.gz cp -r nexus-2.0.4-1 sonatype-work /opt/ ln -s /opt/nexus-2.0.4-1/* /opt/nexus ln /opt/nexus/bin/nexus /etc/init.d/ chmod 755 /etc/init.d/nexus vim /etc/init.d/nexus NEXUS_HOME=“/opt/nexus” RUN_AS_USER=“nexus” useradd -s /sbin/nologin -d /var/lib/nexus nexus chown -R nexus /opt/nexus/ chown -R nexus /opt/nexus-2.0.4-1/ sudo -u nexus cp /opt/nexus/conf/examples/proxy-https/jetty.xml /opt/nexus/conf/ To force Nexus be available through HTTPS I went to Administration - Server - Application Server Settings as admin and changed Base URL to https:// external IP/nexus and set Force Base URL to true. Any ideas how to get missed Nexus features?

    Read the article

  • cfengine3 file_copy only on source side change

    - by megamic
    I am using the 'digest' copy method for all file copy promises, because of the way we package and deploy software, I cant rely on mtime for the criteria for updating files. For various reasons, I am not employing the client-server approach with a central configuration server: rather we package and deploy our entire configuration module to each server, so from cf-engine's perspective, the source and target are local on the server it is running. The problem I am having with this approach is that the source will always update the target when they differ - which is what I want most of the time, usually because the source has been updated. However, like many other cfengine users, we are running an operational environment, where occasionally emergency fixes have to be applied immediately - meaning we don't have time to rebuild and redeploy a configuration module, and the fix will often be applied by deploying a tarball with specific changes. Of course this is problematic if cf-engine comes along 5 mintues later and reverts the changes. What we would like is to be able to make small, incremental changes to our servers, without them being reverted, until the next deployment cycle at which time the new source files would be copied. We do not consider random file corruption or mistaken changes to involve enough risk to warrant having cfengine constantly revert deployments to their source copy - the ability to deploy emergency fixes and have them stay that way until the next deployment would be of much greater value and utility. So, after all that, my question is this: is cf-engine capable of detecting whether it was the source or target that changed when the files differ, and if so, is their a way to use the 'digest' copy method but only if the source side changed? I am very open to other ideas and approaches as-well, as I am still quite new to this whole configuration management thing.

    Read the article

  • How expensive to run PC 24/7 or how to figure out how to determine it?

    - by jasondavis
    I realize this question is difficult to answer as it would be different based on users location, what there PC is doing and what hardware it consist of, along with other factors but I am hoping someone could give me a very rough estimate. I have always ran many PC's in my home 24/7 and I am just now looking at it from a money/cost of electric point of view. 1) I live in Central Florida. Can anyone guesstomate/estimate the avaerage monthly or daily cost of running your average PC? Intel quad core processor, 1 SSD drive for OS and programs and 4-5 1-2 TB hard drives in a RAID setup for data. 750watt PSU. What would your guess be? 2) Also is there an accurate way to figure this out (non-super technical and confusing to a non-math person please) Also I have seen those kill-a-watt devices, do they figure this kind of stuff out for you? 3) Does a larger PSU make your PC consume more power? Thanks for any help, you can most likely tell I am somewhat lost about this!

    Read the article

  • Game login server

    - by Tar
    I have a setup like this: A website, with a database. This database houses accounts and all details. Password hashes/salts/join dates/etc. What I want to do is to be able to use this same database for our game database. The game will be on servers in the United States while the web server and web server database is in the Netherlands. I know there is a big problem with using remote SQL and we really don't want to do that as operation of the website is just as vital as operation of the game server. We had one solution that involved sending account details to another database hosted on the same server that the gameserver is hosted on, but that was incredibly unreliable because if the website was down, no new people could register to play the game. The solution that we want is to have a log in server that is used to check credentials for everything. Is this possible/viable and could anyone point in the right direction? So, in summation: 2 game servers 1 web servers 1 central database used for authorization. The game accounts and website accounts need to be one in the same.

    Read the article

  • Finding cause of TCP retransmission within a LAN

    - by Surreal
    Hello denizens of Server Fault I have an irritating problem with a LAN of about 100 computers, 2 Windows domain servers, and 12 VoIP phones. Since their installation around a year ago, every week or so, we notice a VoIP phone resetting itself - occasionally in the middle of a call. Simultaneously there are often signs of temporary loss of connection on computers: freezes in explorer while accessing network shares, errors in our administration software due to loss of connection to the database server. I have been doing some Wireshark monitoring on the connection between the VoIP PBX and the rest of the network. Wireshark picks up a clump of retransmitted TCP packets at the times when we record phone restarts. The Wireshark log shows about 2 clusters of retransmissions a day ranging from 5 packets to hundreds. Those in each cluster are mainly between the PBX and some set of the VoIP phones, but not always the same set. Often retransmissions at the same time are to phones connected to the same switch, but sometimes retransmissions occur together to phones at opposite ends of the network. There are usually some coincident retransmissions in passing TCP traffic, for example between client machines and the file servers. The spikes in retransmissions and phone resets do not correlate well with when the network is heavily loaded. They seem to occur slightly more during the day, but most in the evening, when traffic should be decreasing. They occur reasonably often late at night when most computers are turned off and traffic should be lowest. Do you have any ideas that might help diagnose the cause of problems like this? One thing I have not yet tried, but should have, is updating the firmware of all the switches.

    Read the article

  • Symantec Endpoint Protection Virus Definitions

    - by Gus Denton
    I have done some Googling but I cannot get a definitive answer certainly not from the Symantec KB. I have a Virtualised Win 2003R2 server 32bit. It has been provisioned to me with Symantec Endpoint Protection 11.0.62xxx CLIENT (not a definitions server) the directory C:\Program Files\Common Files\Symantec Shared\VirusDefs is 750MB IT doesn't contain .tmp directories so it is NOT a corrupt definitions server. IT does contain directories named with a date pattern YYYYMMDD.xxx Some of these folders are 12 months old and I would like to recover the space. The sysmantect forums are full of this stuff but a lot of the postings contain links back to documents that are not specific to End Point Protection Client. It appears that I should be able to delete the older folders and all will be OK. with a service restart however there is a warning about having Live Update Administrator Installed Firstly I have no idea if I have this installed how to I check and secondly can I just ditch these old files and restart ? Regards Gus Denton Learning and Teaching Uni of New South Wales Sydney Australia For those trying to assist me I thankyou. I have followed some instructions found on the Symantec site and assumed that the response from Nixphoe would resolve my issue. It appears that as I am on a provisioned VM from a central IT unit I cannot run the Symantec commands from the Run prompt as my admin creds to get me in. (smc -stop) Basically I need to claw back some Diskspace from the c: drive which is being filed up with WSUS patches and Symantec files. I have managed to delete one symantec cache through the live update control panel and recovered 470Mb I suppose my last question for those more experienced than myself is, can I simply remove say the two oldest virus definition folders without completely foobaring the End Point protection and the server ? Regards Gus

    Read the article

  • Remote Desktop Printing With Color

    - by philibertperusse
    Our ACCPACC administration software runs on an off-site dedicated hosted computer, running Windows 2003 Server with a completely different NT DOMAIN. We have many users connecting to that computer remotely to perform administrative tasks such as printing cheques, printing invoices, printing POs, packing slips and so on. Basically the setup is that we are all connecting using Remote Desktop Protocol (local computers are Mac OS.X, XP SP3, Vista and Windows 7). At our office we have a DOCUCOLOR 242 printer. When printing from the ACCPACC software, it prints to the local printer in our office. This is because we are using RDP features to connect printer ressources to the remote computer. This almost works now. I had to install the printer driver software on the remote 2003 Server for the printer sharing to work. Now, everyone is able to print black and white but color is out. NOTES: Normal users on that Windows 2003 server are running as part of a Group Policy Object to restrict what can be done. I took one of these normal users and gave him all domain administrator rights, no effect still B&W only. I took this account and moved it OUT of GPO policies, as a normal account instead, no effect still B&W only. It seems only MY account (which is domain administrator AND a normal account not part of the GPO objects) can actually print with color. This is the account that was used for installing the printer driver software. How can I manage to get everyone to print in color? Any suggestions as to what to try next?

    Read the article

  • Dell fumbles OpenManage installation process, forgets to write documentation?

    - by bwerks
    Hi all, I'm setting up a Dell PowerEdge 2950 for a small business, and I've just spent a while with Dell OpenManage Server Administrator 6.2, trying to clear the installation process of errors before I execute it. Right now I'm getting the following warning from the installer. The installer has detected that the HTTPS listener is not configured for Windows Remote Management. You can either configure the HTTPS listener before installing Remote Enablement, or install Remote Enablement now by selecting the "Custom" installation screen and configure the HTTPS listener later. See the "Remote Enablement Requirements" section in the "Dell OpenManage Installation and Security User's Guide" for information on configuring the HTTPS listener. Note: Remote Enablement is required to manage this system from a remote Server Administrator Web Server and is applicable only for those systems that support Server Instrumentation. Click here to configure HTTPs Listener for Windows Remote Management. The italicized line is a link, which executes...something...via cmd, and doesn't seem to help the problem. Not knowing exactly what to do here, I consulted the documentation. I read through the Setup and Administration section of the User's Guide, but all that it contained was a weird primer on role-based security and some SNMP stuff. The next section skips installation entirely and moved on to features of the suite. Thinking myself crazy, I consulted the readme, which told me that for installation I should consult the "Dell OpenManage Installation and Security Version 6.2 User's Guide" which not only doesn't exist in the documentation, but also not in all of google? Soo yeah, if anyone is familiar with this problem, drop me some knowledge!

    Read the article

  • Squid proxy in cent os often disconnected with error : tunnelConnectTimeout(): tunnelState->servers is NULL

    - by Ela
    I am having very often internet disconnection problem with Squid proxy service. My server config; OS: CentOS release 6.3 (Final) model name : Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz cpu MHz : 1600.000 My Local systems IP range:192.168.2.x Server IP: 192.168.2.11 Also this server is configured with lamp for development,Samba SMB file service manager and No svn currently. So i see maximum possibility is this squid proxy since this is where it stops to connect and am sure when i restart the server net started working so something wrong with this squid service only. And this server is connected with local 14 other windows machines and basically serves as a central development node. I am able to resolve it by restarting the server fully some time or sometimes by restarting the squid proxy which is totally killing our development. I have attached my cache log file here for the error info. Cache log file Sample error log: 2013/07/01 13:25:38| tunnelConnectTimeout(): tunnelState->servers is NULL 2013/07/01 13:25:41| tunnelConnectTimeout(): tunnelState->servers is NULL 2013/07/01 13:25:41| tunnelConnectTimeout(): tunnelState->servers is NULL 2013/07/01 13:25:50| clientProcessRequest: Invalid Request 2013/07/01 13:26:05| tunnelConnectTimeout(): tunnelState->servers is NULL Some help can make our lives easier, Thanks in advance.

    Read the article

  • Linksys router cannot change default password

    - by Jessica M.
    My wireless internet suddenly stopped working today. I have Windows 7 and Lindsys WRT54G router. I tried to log into the Linksys setup router page by typing in www.192.168.1.1 into firefox and it prompted me for a username and password as usual. The problem is when i tried to enter my regular username and password it did not work. I finally solved my problem when I came across this post here and the very last post solved my problem. It suggested I try username: root / password: admin. For some reason the username and password has been changed. When i tried username: root / password: admin , it worked and allowed me to get into the Linksys setup page. The problem is I can't change the username or password anymore. Every time I want to log into my Linksys setup page I have to enter username: root / password: admin. I can't change the "WPA shared key" (password). For the security settings I selected WPA2Personal + AES. Also the post said "If the firmware was upgraded to non-linksys firmware - the default will be different" . The problem is I didn't update anything and I'm worried that someone installed a virus or something or somehow changed the firmware on my router. How did I get non-Linksys firmware on my router? EDIT: I figured out how to change the password when I log into the Lynksys setup page. Administration -- Management -- password. I still don't understand if my router firmware was changed or who changed it or if it happened by mistake.

    Read the article

  • Lotus Domino - DAOS not reducing file size?

    - by SydxPages
    I have implemented DAOS on a Lotus Domino Server (8.5.3 FP2) as follows: Lotus Domino Server Document: Store file attachments in DAOS: Enabled Minimum size of object before Domino will store in DAOS: 64000 bytes DAOS base path: E:\DAOS Defer object deletion for: 30 days Transaction logging is running, and the specific test database has the following advanced properties set: Domino Attachment and Object Service (ticked) Use LZ1 compression for atachments Compress Database Design Compress Data I have restarted the server. When I run a compact -c, it compacts the database, but does not reduce the size. I have checked the DB in Windows Explorer (60Gb) and the size is the same pre and post. I have checked the directory (E:\DAOS) and it is 35Gb in size. When I run the command 'Tell DAOSMgr Status tmp\test.nsf', I get the following response. From looking up on the net, I believe ticket count = 0 means that the db is not really DAOS'ed? Admin Process: Searching Administration Requests database DAOSMGR: Status tmptest.nsf started DAOS database status: Database: E:\Lotus\Domino\Data\tmp\test.nsf Database state = Synchronized Last resynchronized: 03/09/2012 02:49:13 PM Ticket count: 0 DAOSMGR: Status tmp\test.nsf completed I have run fixup on the database. When I have tried to run the DAOS estimator it has always crashed. This was a problem with larger databases on earlier versions of domino, but not anymore. Can anyone tell me why the size has not reduced? Am I missing anything?

    Read the article

  • Unable to install mod_wsgi on CentOS 5.5 VPS...

    - by jasonaburton
    I am trying to install mod_wsgi on my VPS, but it won't work. This is what I am doing: wget http://modwsgi.googlecode.com/files/mod_wsgi-2.5.tar.gz tar xzvf mod_wsgi-2.5.tar.gz cd mod_wsgi-2.5 ./configure --with-python=/opt/python2.5/bin/python After I run the above command, I get this error: checking for apxs2... no checking for apxs... no checking Apache version... ./configure: line 1298: apxs: command not found ./configure: line 1298: apxs: command not found ./configure: line 1299: /: is a directory ./configure: line 1461: apxs: command not found configure: creating ./config.status config.status: creating Makefile config.status: error: cannot find input file: Makefile.in Through some research I've discovered that I need to modify my command: ./configure --with-apxs=/usr/local/apache/bin/apxs \ --with-python=/usr/local/bin/python But, /usr/local/apache/ doesn't exist, or so that's what it is telling me. If it doesn't exist, how do I create it with all the files needed, or if apache is located elsewhere on my VPS where would it be located? I'd also like to mention that I ran a command to install apache before this entire deal: yum install httpd so I assumed that was all I needed but apparently not (I am very new at all this server administration stuff so please be gentle) EDIT: This is the tutorial that I have been using to get this all set up: http://binarysushi.com/blog/2009/aug/19/CentOS-5-3-python-2-5-virtualevn-mod-wsgi-and-mod-rpaf/ I got stuck at the heading "Installing mod_wsgi" Thanks for any help!

    Read the article

< Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >