Search Results

Search found 10603 results on 425 pages for 'device emulation'.

Page 134/425 | < Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >

• Most transparent way to connect two LANS using a WET610N Wireless Bridge

  - by Spencer Ruport

  I have two wired systems hooked to a Linksys WRT54GL wired/wireless router which is also hooked to my internet. I'll refer to this as LAN1. I have two more systems in another room that are connected wirelessly. Recently I decided I would much rather have another wired LAN in the other room and use a bridge to connect them. This would be LAN2. Prior to hooking up the device I assumed that the ethernet side of the bridge would have a DHCP server so that I could simply hook it up to a switch and I'd be on my way. However that isn't the case which leads me to believe I'll have to add one to LAN2 correct? Or is there some way to have the DHCP from LAN1 also hand out IP addresses to LAN2? If I do need a DHCP device on LAN2 what would be best? Another hardware device or should I just install some DHCP software on one of the systems (since they're both on 24/7 anyway). Any recommendations would be appreciated. :)

  Read the article

• Wireless USB keyboard and mouse can wake system, but then receiver is inactive

  - by BlueMonkMN

  I have a Microsoft brand USB device that acts as a receiver for a wireless Microsoft Keyboard and a wireless Mouse. When it's operating normally, there are LEDs on the device indicating Caps Lock, Num Lock and Function Lock, of which the latter 2 are usually lit. It is plugged into a Dell Isnpiron 531 with Windows 7 32-bit running on an AMD Athlon 64 X2 Dual Core processor 5000+. When the computer goes to sleep (the power indicator on the main box is flashing), I can wake it by moving the mouse. So far all is good. However, something changed in, I think, the past couple weeks (I suspect due to a Microsoft driver update problem). Before the change, after waking the computer, everything would operate normally as far as I could tell, but now after waking the computer, the receiver has no lights on, and the keyboard and mouse are completely unresponsive (which is odd, considering the mouse woke up the computer). There is a button on the receiver that's supposed to reset the wireless connection and flash the lights while it does so, but it has no effect in this state. It's like the receiver doesn't have power (but how would the system know I moved the mouse, unless the power was on until it woke up?). I have checked the BIOS/CMOS settings or whatever you call them, and did not see anything related to USB in the power management section. I have checked Windows 7 device manager and ensured that all the USB Root Hub devices have the setting unchecked for allowing the USB power to be turned off. Like I said, this was working before, and the only thing I can think of that's changed is applying Windows Updates.

  Read the article

• Prolific USB-to-Serial Comm Port significantly slower under Windows 7 comparing to Windows XP

  - by Dmitry S

  Not sure if this question should be asked here or on SuperUser but if we get an answer here it may be useful for others here I am using a Prolific USB-to-Serial adapter based on the Prolific chip to use with a device on serial port. I have the latest version of the driver installed: 1.3.0 (2010-7-15). When I use my device with this adapter on my main Windows 7 (32bit) system it takes 8-9 seconds to send a command through to the device. However, when I do the same thing on a different Windows XP system (an old laptop I borrowed for testing) it only takes 2-3 seconds. I have made sure that the port settings and other variables are the same between systems. I also tested on a third laptop (also running Windows 7) and again got a significant delay. So the question is if anyone else experienced the same problem and found a solution. I would like to avoid moving to an XP system for what I need to achieve so that's my last option. Thanks in advance.

  Read the article

• Filtered Router Interface

  - by jviotti

  I'm having some problems with a Scientific-Atlanta DPR2320R2. In specific with the WIFI. A few months ago I changed its password and username and now I can't remember. So I tried cracking it with Hydra but it drove things worse. Content of webadmin was rendered partial, and threw lot of errors. I then reseted the router. I found myself abled to browse the web with ethernet-connected pc. Wifi is configured by registering the device's MAC Address, and indeed the router has been reseted and register MAC address were lost. No device could connect to wifi. In fact, the device does not even recognize the network. I tried the pointing to 192.168.0.1 to restablish the MAC's. But I couldn't connect to the router access point. Tried listing up hosts: $ nmap -sP 192.168.0.0/24 Starting Nmap 5.00 ( http://nmap.org ) at 2012-12-11 01:18 ART Host 192.168.0.1 is up (0.0018s latency). Host 192.168.0.11 is up (0.00025s latency). Nmap done: 256 IP addresses (2 hosts up) scanned in 59.62 seconds Then checked 192.168.0.1 was really up by sending pings. It responded to all my pings. I quick-scanned the access point: $ nmap 192.168.0.1 Starting Nmap 5.00 ( http://nmap.org ) at 2012-12-11 01:08 ART Interesting ports on 192.168.0.1: Not shown: 999 closed ports PORT STATE SERVICE 80/tcp filtered http Nmap done: 1 IP address (1 host up) scanned in 6.73 seconds Look the state of the port 80: FILTERED. I'm pretty confused now. Any suggestion would be appreciated. Thanks in advance.

  Read the article

• corrupted, hidden, wireless network adapter from "Network Connections" in Windows 7

  - by srihari reddy

  The issue is that when I install a wireless network adapter on my Windows 7 Professional machine I have no connectivity, the system tray icon has a red X. First, I tried the obvious, install updated drivers from the manufacturer. When I did this, the Network Connections icon had gray bars and there was no connectivity. So I tried installling the network adapter on a different computer on the same network and I verified that it does work with no issues. Next, I ran scan disk with no issues. Next, I ran sfc as admin with no issues. At this point I turned to the router and turned SSID broadcast on but that didn't help. I turned MAC address filtering off at the router but that didn't help. Whenever I installed the original network adapter (a wireless N usb adapter with WPA2 TKIP+AES) it showed up as "Wireless Network Connection 2" with a grayed out icon and no connectivity. Lastly, I tried installing two different "verified working" usb wireless adapters on to the Windows 7 Pro machine. The results were the same "Wireless Network Connection 2" that had a green bar icon but no connectivity. I installed the manufacturers software and it indicated the NIC was not there even thought the driver installed successfully in Device Manager. I guess I should mention, I first tried (insanely in vain) to use the (worthless) Windows Network troubleshooter. The results were....drumroll please... There is a problem with the network adapter... well No Duh! Also, during all of this the network adapter is always showing as "Working Properly" in the properties dialogue of Device Manager for the wireless NIC. I checked for hidden devices in Device Manager but there were none. Here is my fundamental question that I've tried to find in the Windows 7 support center with no luck. How do I remove/delete/uninstall network adapters from the Windows 7 registry? in particular hidden, corrupted network adapters, that used to be working.

  Read the article

• Diverting sound output of MCE to SPDIF

  - by Saxtus

  I have an ASUS SupremeFX II audio card (which in fact is an onboard audio riser slot) with the default drivers that are pre-installed by Windows 7 x64 for this card. I am able to manually switch between analog output and SPDIF output by the means of control panel (or external utilities like STADS), a change that affects all applications. The problem is that by doing that every time I am about to launch Windows Media Center, except that it's not that elegant, also makes all other Windows application's sounds to pass through SPDIF too, bypassing analog output completely, blending with what I am watching at Windows Media Center. Is there a way to make SPDIF as the default playback device for Windows Media Center? I know other programs that have a setting like that (foobar2000 for example) working like charm, allowing me to even have different outputs working at the same time (tested with my current card successfully). But when comes to Windows Media Center... it just use what the default playback device is all the time. The only setting that I know of, is under: Settings General Windows Media Center Setup Set Up Your Speakers and what it does is to just change the default playback device for entire system. Please help!

  Read the article

• What's up with stat on Macos/Darwin? Or filesystems without names...

  - by Charles Stewart

  In response to a question I asked on SO, Give the mount point of a path, one respondant suggested using stat to get the device name associated with the volume of a given path. This works nicely on Linux, but gives crazy results on Macos 10.4. For my system, df and mount give: cas cas$ df Filesystem 512-blocks Used Avail Capacity Mounted on /dev/disk0s3 58342896 49924456 7906440 86% / devfs 194 194 0 100% /dev fdesc 2 2 0 100% /dev 1024 1024 0 100% /.vol automount -nsl [166] 0 0 0 100% /Network automount -fstab [170] 0 0 0 100% /automount/Servers automount -static [170] 0 0 0 100% /automount/static /dev/disk2s1 163577856 23225520 140352336 14% /Volumes/Snapshot /dev/disk2s2 409404102 5745938 383187960 1% /Volumes/Sparse cas cas$ mount /dev/disk0s3 on / (local, journaled) devfs on /dev (local) fdesc on /dev (union) on /.vol automount -nsl [166] on /Network (automounted) automount -fstab [170] on /automount/Servers (automounted) automount -static [170] on /automount/static (automounted) /dev/disk2s1 on /Volumes/Snapshot (local, nodev, nosuid, journaled) /dev/disk2s2 on /Volumes/Sparse (asynchronous, local, nodev, nosuid) Trying to get the devices from the mount points, though: cas cas$ df | grep -e/ | awk '{print $NF}' | while read line; do echo $line $(stat -f"%Sdr" $line); done / disk0s3r /dev ???r /dev ???r /.vol ???r /Network ???r /automount/Servers ???r /automount/static ???r /Volumes/Snapshot disk2s1r /Volumes/Sparse disk2s2r Here, I'm feeding each of the mount points scraped from df to stat, outputing the results of the "%Sdr" format string, which is supposed to be the device name: Cf. stat(1) man page: The special output specifier S may be used to indicate that the output, if applicable, should be in string format. May be used in combination with: ... dr Display actual device name. What's going on? Is it a bug in stat, or some Darwin VFS weirdness? Postscript Per Andrew McGregor, try passing "%Sd" to stat for more weirdness. It lists some apparently arbitrary subset of files from CWD...

  Read the article

• What's up with stat on Mac OS X/Darwin? Or filesystems without names...

  - by Charles Stewart

  In response to a question I asked on SO, Give the mount point of a path, one respondant suggested using stat to get the device name associated with the volume of a given path. This works nicely on Linux, but gives crazy results on Mac OS X 10.4. For my system, df and mount give: cas cas$ df Filesystem 512-blocks Used Avail Capacity Mounted on /dev/disk0s3 58342896 49924456 7906440 86% / devfs 194 194 0 100% /dev fdesc 2 2 0 100% /dev <volfs> 1024 1024 0 100% /.vol automount -nsl [166] 0 0 0 100% /Network automount -fstab [170] 0 0 0 100% /automount/Servers automount -static [170] 0 0 0 100% /automount/static /dev/disk2s1 163577856 23225520 140352336 14% /Volumes/Snapshot /dev/disk2s2 409404102 5745938 383187960 1% /Volumes/Sparse cas cas$ mount /dev/disk0s3 on / (local, journaled) devfs on /dev (local) fdesc on /dev (union) <volfs> on /.vol automount -nsl [166] on /Network (automounted) automount -fstab [170] on /automount/Servers (automounted) automount -static [170] on /automount/static (automounted) /dev/disk2s1 on /Volumes/Snapshot (local, nodev, nosuid, journaled) /dev/disk2s2 on /Volumes/Sparse (asynchronous, local, nodev, nosuid) Trying to get the devices from the mount points, though: cas cas$ df | grep -e/ | awk '{print $NF}' | while read line; do echo $line $(stat -f"%Sdr" $line); done / disk0s3r /dev ???r /dev ???r /.vol ???r /Network ???r /automount/Servers ???r /automount/static ???r /Volumes/Snapshot disk2s1r /Volumes/Sparse disk2s2r Here, I'm feeding each of the mount points scraped from df to stat, outputting the results of the "%Sdr" format string, which is supposed to be the device name: Cf. stat(1) man page: The special output specifier S may be used to indicate that the output, if applicable, should be in string format. May be used in combination with: ... dr Display actual device name. What's going on? Is it a bug in stat, or some Darwin VFS weirdness? Postscript Per Andrew McGregor, try passing "%Sd" to stat for more weirdness. It lists some apparently arbitrary subset of files from CWD...

  Read the article

• What GPT partition type to use for protecting DRBD metadata?

  - by Carsten Scholtes

  I'm planning to install a DRBD device on a (replicated) disk with two GPT partitions. DRBD requires some space for (preferentially "internal") metadata at the end of the underlying device. I'm hesitant to leave this space unpartitionend (or unformatted in a normal partition). I'd like to reserve an extra partition at the end of the underlying disk device for the metadata. (If I understand correctly, DRBD would not care about the partition or its type and could then use that space exclusively.) My question is: Which would be a suitable GPT partition type for such a metadata partition? It should not be a type interpreted while booting (such as EF00 EFI System). It should not be a type prone to be modified accidentialy by the booted OS (such as 8200 Linux swap, 8e00 Linux LVM, fd00 Linux raid). (The booted OS will be Ubuntu Linux 12.04.3.) It should not be a type indicating a normal filesystem (such as 0c01 or 8301), prone to be formatted correspondingly. It should not be a type requiring any special content in the partition (since the content is to be handled exclusively by DRBD). It should express the purpose of being reserved for something special (namely DRBD). (The types I listed are as provided by gdisk. I'm thinking about using some type unlikely to be used by the OS (maybe bf0a Solaris Reserved 4) or an invented(?) type such as fd01 (close to fd00 Linux raid…). Would something like this be suitable, too dangerous or even possible?)

  Read the article

• None of usb-controllers are working after a crash

  - by Cray

  So I have a GA-p35-DS4 mboard with a Q6600, running windows7-x64. After a random crash with a bluescreen (not caused by anything particular as I recall), none of the usb-controllers are working. (And none of the devices connected to those usb ports). All the controllers are showed up in the device manager, but every one has a warning-icon (as they are not functioning properly). The windows identifies them correctly, it shows exactly the model of each controller, and it says that the driver is installed. Now, when I try to reinstall the driver (Update driver menu item in the device manager), it tries to find it, finds the driver, but quits saying that the driver was found but could not be installed. Additionally, it displays "This operation requires an interactive window station", whatever that means... Now get this, the same thing happens with a new pci-usb controller card! It is found (actually each time the machine starts, it is found as new hardware), but trying to install drivers leads nowhere, I am getting the same message about an interactive window station. (tried to install drivers from the acoompanying CD) I have tried deleting those devices from device manager and let windows find them again, but that leads to same results. None of the ports on this extension card work either. This should not be a hardware problem, a usb keyboard connected to the builtin usb controller works in bios, and even in another OS running the same computer (old xp installation) What to do? Will I have to reinstall? Can deleting infcache.1 help? Is there some way to let windows remove all old drivers and try to find all hardware again, this time only looking for drivers on a windows install disk or something?

  Read the article

• Can't mount FAT32 drive under Ubuntu Linux

  - by Josh

  I have a 320GB USB drive with a single large FAT32 partition. The volume mounts perfectly fine on my Mac OS X 10.5.8 machine and Disk Utility on the mac reports no issues with the volume. I can read/write all data on the drive. However when I connect the drive to my Ubuntu 9.10 Karmic system, the partition does not mount. dmesg|tail says: [ 2752.334822] scsi3 : SCSI emulation for USB Mass Storage devices [ 2752.335040] usb-storage: device found at 3 [ 2752.335044] usb-storage: waiting for device to settle before scanning [ 2757.330301] usb-storage: device scan complete [ 2757.331005] scsi 3:0:0:0: Direct-Access WD 3200AAK External 1.65 PQ: 0 ANSI: 0 [ 2757.331772] sd 3:0:0:0: Attached scsi generic sg2 type 0 [ 2757.355647] sd 3:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 2757.360737] sd 3:0:0:0: [sdb] Write Protect is off [ 2757.360749] sd 3:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 2757.360755] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367618] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367631] sdb: sdb1 [ 2762.797622] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2762.797636] sd 3:0:0:0: [sdb] Attached SCSI disk [ 2822.866228] FAT: bogus number of reserved sectors [ 2822.866237] VFS: Can't find a valid FAT filesystem on dev sdb1. When I run fsck.vfat -a /dev/sdb1 I get: root@cartman:~# fsck.vfat -a /dev/sdb1 dosfsck 3.0.3, 18 May 2009, FAT32, LFN Logical sector size is zero. Googling "vfat Logical sector size is zero" produced no consensus as to the solution. I would prefer not to have to completely reformat the disk if possible because it contains about 280GB of data I would rather not have to find a temporary home for. Any suggestions?

  Read the article

• Resources for Smartphone Security

  - by Shial

  My organization is currently working on improving our data and network security due to increasing HIPAA laws and a general need to get a better grasp on controlling our health related information. We are a non-profit working with people with developmental disabilities so we handle a lot of medical related information. One area that has been identified as a risk is our use of smartphones, specifically at this time Windows Mobile 6.1 devices from T-Mobile. We do not utilize the VPNs on the phones so there isn't any way they can access our databases or file servers (username/password for VPNs is not the domain logons). What would be exposed however is the particular user's email account since you could extract out the username/password and access the email either on the device or on our web email (Exchange 2003) which could contain HIPAA protected confidential information about clients and services and this would be an incident that would have to be reported. What resources or ideas would help us secure these devices? I'm not worried about data interception (using SSL) but more about physical theft or loss of the device. Are there websites that I just have not found with guidelines and suggestions or particualar products that would help protect us? I also don't want to limit the discussion to windows Mobile either. I myself am looking at an android 2.0 device and there is always the eventual possibility we could get pushed to enable the VPNs. I know this is a subject that likely won't have any particular correct answer and it is something we should all be aware of since there devices are sitting outside of our immediate control most of the time.

  Read the article

• CentOS networking BNX2

  - by james moore

  Having some trouble with my NICs. The server starts fine and I can wget/ping etc. However, when I /etc/init.d/networking restart I then receive the following error: Bringing up interface eth0: bnx2: fw sync timeout, reset code = 1030009 SIOCSIFFLAGS: Device or resource busy Consequently, the task fails. I have searched around on google users suggesting to disable PNP in the BIOS but I see no option. Here is some system information: $ ethtool -i eth0 driver: bnx2 version: 2.0.8-rh firmware-version: bc 2.9.1 $ uname -a Linux host 2.6.18-238.9.1.el5 #1 SMP Tue Apr 12 18:10:13 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux $/sbin/lspci | grep Broadcom 04:00.0 PCI brodge: Broadcom EPB PCI-Express to PCI-X Bridge (rev c3) 05:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5700 Gigabit Ethernet (rev 12) 08:00.0 PCI brodge: Broadcom EPB PCI-Express to PCI-X Bridge (rev c3) 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5700 Gigabit Ethernet (rev 12) $ lsmod | grep bnx2 bnx2i 81704 0 cnic 109512 1 bnx2i libiscsi2 77765 6 be2iscsi,ib_iser,iscsi_tcp,bnx2i,cxgb3i,libiscsi_tcp scsi_transport_iscsi2 73945 8 be2iscsi,ib_iser,iscsi_tcp,bnx2i,cxgb3i,libiscsi2 bnx2 224780 0 scsi_mod 199001 15 mpt2sas,scsi_transport_sas,mptctl,be2iscsi,ib_iser,iscsi_tcp,bnx2i,cxgb3i,libiscsi2,scsi_transport_iscsi2,scsi_dh,sg,libata,megaraid_sas,sd_mod $ rmmod bnx2; modprobe bnx2 PCI: Enabling device 0000:05:00.0 (0158 -> 015a) PCI: Enabling device 0000:09:00.0 (0158 -> 015a) bnx2: fw sync timeout, reset code = 10300003 Any help would be appreciated as I am at a loss.

  Read the article

• Toshiba External Hard Drive freezes computer

  - by Ephraim

  I bought a Toshiba Canvio Basics E05A032BAU2XK Portable External 320GB 2.5 Hard Drive: My computer has two Os's on it Win7 and Win XP. I need both. The main one I use is XP. When booting my computer in any OS the computer and hard drive work fine. The same holds true for plugging in the hard drive while running Win7. However, when running WinXP, if the hard drive gets plugged in the computer freezes(my main point is that the HD is portable so it is essential that it does not do this, as I said I usually run XP). After reading some online forums I was informed that there is a compatibility issue with the newest version of Eset Smart Security(I still don't understand this because it works fine in Win7 or when connected on boot...). I disabled the AV and plugged in the HD... Walla! The comnputer did not freeze. However the disk is not recognized in explorer or disk management. In device manager I removed the device and did a scan and installation of device failed. It pretty much sounds like a driver issue but I cannot find any drivers for this HD. In fact, Toshiba claims that there are no downloadable drivers for it and that XP should take care of the drivers itself. What to do? As far as I can tell, all other USB devices work just fine on both OS. Please Help!

  Read the article

• Linux Mounting Problem

  - by Sam

  I have an Iomega Network Attached Storage device on my Windows network. I am trying to use a clonezilla live USB flash drive to backup my netbook to my Iomega Network Attached Storage device. The clonezilla USB flash drive runs linux. I'm having trouble getting the Network Attached Storage unit to mount using the following command: mount -t cifs -o username="myUsername" //192.168.1.100/backup /home/partimg The response from linux is: [134.730738] CIFS VFS: cifs_mount failed w/return code = -6 retrying with upper case share name [134.788461] CIFS VFS: cifs_mount failed w/return code = -6 mount error(6): No such device or address Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) I also tried adding the following to my username: username="myUsername,domain=workgroup" but that did not change the error. I am able to ping the network attached storage unit from linux on my netbook. I also booted from a Slax Live USB Flash Drive and Slax auto-mounted my network attached storage unit via Samba. Unfortunately, I don't believe that I can run clonezilla from inside the Slax installation. Does anyone have any insight about what is wrong with my mount statement? Or is there something peculiar about Iomega drives which makes this impossible?

  Read the article

• Access Windows Boot Manager selector when timeout is set to 0?

  - by Kyle Cronin

  I've installed Wubi onto a Windows Vista computer. I've also set the boot timeout to 0: bcdedit /timeout 0 However, now I can't figure out how to get the menu to come up at all! I read on the internets that I had to hold F8 or space when starting up, but they doesn't seem to do anything. Is there a different key or setting I've overlooked? The computer itself is a Dell that's a few months old. The keyboard is USB, but I don't think that's the problem as I can get into the BIOS just fine. Maybe I'm doing it wrong? Am I supposed to hold the keys or rapidly tap them (I've tried both)? If it helps, here's the output from bcdedit: C:\Windows\system32>bcdedit Windows Boot Manager -------------------- identifier {bootmgr} device partition=C: description Windows Boot Manager locale en-US inherit {globalsettings} default {current} resumeobject {5460d9d2-d391-11dc-9d9f-aba67a8797c5} displayorder {current} {e2484fe7-5e97-11de-84d4-0024e8074422} toolsdisplayorder {memdiag} timeout 0 resume No Windows Boot Loader ------------------- identifier {current} device partition=C: path \Windows\system32\winload.exe description Windows Vista locale en-US inherit {bootloadersettings} recoverysequence {572bcd55-ffa7-11d9-aae0-0007e994107d} recoveryenabled Yes osdevice partition=C: systemroot \Windows resumeobject {5460d9d2-d391-11dc-9d9f-aba67a8797c5} nx OptIn Real-mode Boot Sector --------------------- identifier {e2484fe7-5e97-11de-84d4-0024e8074422} device partition=C: path \ubuntu\winboot\wubildr.mbr description Ubuntu

  Read the article

• Copy from CDROM is very slow in Ubuntu

  - by ???

  I'm using the command to copy CDROM image: # dd if=/dev/sr0 of=./maverick.iso But it's very slow, at about 350k bytes/sec. I've searched the google, and try the command # hdparm -vi /dev/sr0 /dev/sr0: HDIO_DRIVE_CMD(identify) failed: Bad address IO_support = 1 (32-bit) readonly = 0 (off) readahead = 256 (on) HDIO_GETGEO failed: Inappropriate ioctl for device Model=DVD-ROM UJDA775, FwRev=DA03, SerialNo= Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic } RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=unknown, BuffSize=unknown, MaxMultSect=0 (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0 IORDY=yes, tPIO={min:180,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4 DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 *udma2 AdvancedPM=no Drive conforms to: ATA/ATAPI-5 T13 1321D revision 3: ATA/ATAPI-1,2,3,4,5 * signifies the current active mode Seems like DMA is already on. And a device test gives: # hdparm -t /dev/sr0 /dev/sr0: Timing buffered disk reads: 2 MB in 6.58 seconds = 311.10 kB/sec # sudo hdparm -tT /dev/sr0 /dev/sr0: Timing cached reads: 2 MB in 2.69 seconds = 760.96 kB/sec Timing buffered disk reads: m 4 MB in 5.19 seconds = 789.09 kB/sec The CD-ROM device and disc should be okay because I can copy it very fast in Windows, using UltraISO utility. So I guess there is something not configured right in Ubuntu, is it?

  Read the article

• bond0 and xen = crash

  - by Rajat

  Bonding with xen 1 - Stop all guests. Reboot dom0 after running "chkconfig xend off" and "chkconfig xendomains off". 2 - Configure bond0 by enslaving eth0 and eth1 to it. I added the below two entries to /etc/modprobe.conf. alias bond0 bonding options bond0 mode=6,miimon=100 Content of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none Content of /etc/sysconfig/network-scripts/ifcfg-eth1 DEVICE=eth1 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none Content of /etc/sysconfig/network-scripts/ifcfg-bond0 DEVICE=bond0 IPADDR= NETMASK= ONBOOT=yes BOOTPROTO=static USERCTL=no Did "modprobe bond0" and "service network restart" after that. 3 - Edit /etc/xen/xend-config.sxp Change (network-script network-bridge) To (network-script 'network-bridge netdev=bond0') 4 - Start xend. "service xend start". 5 - chkconfig xend on. 6 - modprode bond0 7 - more /proc/net/bonding/bond0 8 - Create guest images as usual and bridge it to xenbr0. about config i did for my xen kernel rhel 5.3 after i reboot the host server i get in place bond0 get pbond0 and its get disconnect from network only i ping to my vm's on the host server any one have any idea why xen bond0 is acting like that or what is solutions to come out of pbond0 to bond0.

  Read the article

• USB drive dead after stopping copying process on Snow Leopard Server

  - by Anriëtte Combrink

  Hi there I was copying to a flash drive from our Snow Leopard server when I stopped the copying process half way through. The device then disappeared from the Desktop. So I unplugged it and plugged it right back in. The device just didn't show up. I unplugged it and plugged it into a Windows XP machine as well as a Windows 7 machine. On both machines, I right clicked "My Computer" and selected "Manage…". On both PC's, the device was located under Removable Storage, but had no size and no drive letter. It shows up in "My Computer", but when I choose "Format…" from the right-click menu (context menu), it says the drive could not be formatted. Can someone please advise me? The flash drives is about 5 mins old and should have no reason to be dead. I really can't loose this drive (I don't need the data on it, I just need it to work again), any help would be appreciated. Thanks in advance.

  Read the article

• Auto-rebuild RAID6 with MDADM

  - by user65632

  Hello everybody, i'm new in this forum, and because I see that a lot of people get helped here, i'll ask my question here! I have a openSUSE 11.3 Linux computer with 5 disks of 1TB (WD enterprise disks) in it. with mdadm I configured an RAID6 device. Now, after a lot of thorough testing, i've noticed that when the computer goes down unsuspectedly it could happen (1 time out of 10) that while booting, the md0 device isn't recognised, and then the machine goes in "recovery mode", which means that i have to 'CTRL + C' it so it can boot to openSUSE. Once in openSUSE i have to readd the drive manually with 'mdadm /dev/md0 --add /dev/sdX'. After this everything works back fine (after resynching). So my question is: Is there a way to auto-rebuild the RAID6 device when there are problems? and how can I stop this "recovery mode" from happening. Because the computer will be in a place I can't go to, to connect a keyboard, 'CTRL + C' it just to get in openSUSE. If you could help me, I would be a very very very! happy man! :-) thanks in advance! Mikhail

  Read the article

• CUPS causes printer to click and doesn't print

  - by Pez Cuckow

  I'm suffering a strange problem with my Cannon iP4850 when trying to use CUPS on a Raspberry Pi (this is not RPi specific, please do not vote to move it). When I plug the printer into my Laptop (OSX) or my Desktop W7 it identifies as a iP4800 and prints perfectly. So I plug it into the Pi (running debian), set it up in CUPS enable sharing and can now see the iP4800 series shared on the network. However if I print to it (using AirPrint etc...); the file gets to CUPS safely (shows in the queue) but when it tries to print the printer clicks (like a loud thunk) 3/4 times and then gives in, with a double amber flashing light. In cups it shows as job completed. Do you know why using the pi and cups would cause what appears to be a hardware fault and what I can do to fix the problem or to provide further debug info? Thanks for your time! Description: Canon iP4800 series Location: Lounge Driver: Canon PIXMA iP4800 - CUPS+Gutenprint v5.2.9 (color, 2-sided printing) Connection: usb://Canon/iP4800%20series?serial=2239B2 Note: I've tried deleting and re-adding the printer to the Laptop, Desktop and PI and the results are always the same Log for plugging in printer and printing (attempting to) something until the printer turned off again pi@pezpi /var/log $ dmesg [ 7284.176336] usb 1-1.2: new high speed USB device number 8 using dwc_otg [ 7284.279703] usb 1-1.2: New USB device found, idVendor=04a9, idProduct=10d5 [ 7284.279750] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7284.279771] usb 1-1.2: Product: iP4800 series [ 7284.279786] usb 1-1.2: Manufacturer: Canon [ 7284.279800] usb 1-1.2: SerialNumber: 2239B2 Setting cups to verbose: Change loglevel in cupsd.conf to debug (or debug2) pi@pezpi /var/log $ sudo vim /etc/cups/cupsd.conf pi@pezpi /var/log $ sudo /etc/init.d/cups restart [ ok ] Restarting Common Unix Printing System: cupsd. pi@pezpi /var/log $ Log from $ /var/log/cups/error_log is at http://pastebin.com/7VZMRMrG (too large to post here) The log contains - in order (deleted the log and then did the beneath) Restarting the cups server Attempting to print a test page x2 Printing from 192.168.1.90 via AirPrint Printing from 192.168.1.90 via Network Print Turning the printer off and on again

  Read the article

• Cisco Spam Blocker, Iron Port, Lotus Domino, Integration Help

  - by NickToyota

  Hi serverfault universe, I work for a medium sized (roughly 200 user) company. We are attempting to intagrate our new Cisco Spam Video Blocker (ironport) device into our network so that it acts as an incoming filter then passes it off to our Lotus domino mail server. And also vise versa. The way our network is setup currently has an mx record pointing to our Domino mail SMTP incoming server which is currently setup to be an inbound gateway and filter (using symantec domino mail software). We want to replace the inbound gateway with the ironport. Our company has also invested in a pool of external IP addresses which I believe has been currently assigned to our web, email, servers. What would the proper course of action be to successfully integrate the device be? Mx record change? Replace the domino gateway completely with the ironport? We attempted to set the ironport device to the external IP of what our mx record is pointing to without much success. Any help on proper setup would be greatly appreciated.

  Read the article

• Raid1 with active and spare partition

  - by Daniel Baron

  I am having the following problem with a RAID1 software raid partition on my Ubuntu system (10.04 LTS, 2.6.32-24-server in case it matters). One of my disks (sdb5) reported I/O errors and was therefore marked faulty in the array. The array was then degraded with one active device. Hence, I replaced the harddisk, cloned the partition table and added all new partitions to my raid arrays. After syncing all partitions ended up fine, having 2 active devices - except one of them. The partition which reported the faulty disk before, however, did not include the new partition as an active device but as a spare disk: md3 : active raid1 sdb5[2] sda5[1] 4881344 blocks [2/1] [_U] A detailed look reveals: root@server:~# mdadm --detail /dev/md3 [...] Number Major Minor RaidDevice State 2 8 21 0 spare rebuilding /dev/sdb5 1 8 5 1 active sync /dev/sda5 So here is the question: How do I tell my raid to turn the spare disk into an active one? And why has it been added as a spare device? Recreating or reassembling the array is not an option, because it is my root partition. And I can not find any hints to that subject in the Software Raid HOWTO. Any help would be appreciated.

  Read the article

• MicroSD card isn't detected by computer, apparently usable only with phone

  - by paulcjoubert

  I have a 4GB MicroSD card that apparently only works (in the sense that the device detects and can read and write from and to the card) with my old Nokia XpressMusic 5800 phone. I have taken pictures and recorded voice notes that were saved on the card. These are accessible after the card has been removed, which tells me that the problem isn't with the card. The card could also not be locked to the phone as it would at least be detected by a computer and it would be able to write raw data to it with dd, such as /dev/zero. Also, the card is not the Nokia card that came with the phone and I have done nothing that would have caused it to be locked. (I could not find anything on Nokia's website that helps, but then again... my search was not THAT thorough.) The card works on no other device that I have tried so far. I have tried it in my Canon camera (through an adapter), but it refuses to even boot with the card inserted. My card reader (via USB cable and hub) is detected as /dev/sdx with or without the card inserted. When trying to access the card I get an "No medium found". dmesg does not report any change at all when inserting and removing the card. I would obviously like to use my card on other devices - the phone is quite old - and even a likely explanation would help. Thankyou in advance! EDIT 1: I can use the card by connecting the phone to my computer, but this is impractical and would not allow me to use the card in any other device. EDIT 2: The data on the card is not important to me at all.

  Read the article

• hp proliant dl360 disk diagnostic issue

  - by user1039384

  We recently got two used drives (15000) and installed on our HP proliant dl360 G5 server. Created RAID1 and used HP SmartStart CD to perform diagnostics. Interestingly, the Diagnostic tab immidiately fails on Logical drive testing saying the Disk1 should be replaced, while the Test tab successfully runs all the complete tests on both disks and does not find any issue. At the meantime, when booting to esxi 5, vSphere periodically shows the Disk1 as Unknown and Logical drive in recovery process. This happens every 5-10 minutes. Here is the log from HP SmartScan diagnostic: 1 - Device, Test: Logical Drive 1, Storage Controller in Slot 0 1 - Description: The controller has reported a critical error in the drive error log. 1 - Recommended Repair: This drive should be replaced. 1 - Failed Count: 44 1 - Error code: F157 There is also another error log record (see below): 2 - Device, Test: test_components/libstorage.so ID 2 - Description: An unexpected exception occurred while performing an operation. Exception message: CISS_StatusHandler::evaluate: commandStatus = 4 (INVALID); hexdump of CISS_ErrorInfo: 00000000: __ __ 04 __ 20 __ __ __ __ __ __ __ __ __ __ __ .... ... ........ 00000010: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ 00000020: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ Device: Hard Drive 2, Storage Controller in Slot 0 Property name: Bad Target Count 2 - Recommended Repair: Reboot or restart Insight Diagnostics. Retry the test. If the problem persists, upgrade to the latest version of Insight Diagnostics. 2 - Failed Count: 48 2 - Error Code: F62 Note that rebooting didn't help and I was running the latest diagnostic software version. Anyone has a clue? Is this a real disk issue? BTW, the controller is Smart Array E200i Thanks in advance

  Read the article

< Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >