Search Results

Search found 6523 results on 261 pages for 'route planning'.

Page 134/261 | < Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >

• IPv6 connections routed to IPv4 device

  - by Yvan JANSSENS

  I have an IBM 9406-250 with V5R1 and IPv4 only connectivity, and want it to be reachable over IPv6. I cannnot install an IPv6 stack on it, but I want it to be accessible by IPv6 so I can drop the requirement to VPN to my home network. I have an OpenWRT device running, which takes care of the IPv6 routing on my network and the tunnel to SIXXS, and I was wondering if it is possible to assign another IPv6 address to that device, and route it to the IPv4 IBM computer. Which software do I need for this, and how is this technique called?

  Read the article

• How do I make a privileged port non-privileged in Redhat 5?

  - by Jason Thompson

  So I have a RedHat 5 box that I'm wanting to run an application that I wrote that implements SLP. SLP uses port 427 for answering service queries. My understanding is that ports below 1024 are "privileged" and thus cannot be bound to by anyone that's not root. I cannot run this application as root as it is launched via tomcat. One creative solution I really like was simply writing an iptables rule to route the privileged port to a non-privileged. In my proof of concept tests, this works wonderfully. Unfortunately, it would be greatly (and understandably) desired by the powers if my application did not require screwing around with iptables upon installation. So I heard a rumor and cannot find anything to verify this that there was some sort of command or parameter that could be set to make any port I want be non-privileged. Is this true? If so, how is this done? Thanks!

  Read the article

• Cisco NAT + IPSec + Web Server Configuration Question

  - by zagman76

  Hello - I currently have a Cisco 881W, and it is configured with one of our static IPs to do basic NAT for the network. We also have a web server that needs it's own IP. I configured the NAT for the 2nd IP, however now traffic through our IPSec VPN doesn't route to the web server properly (well, it routes to the internet, rather than through the Tunnel). I followed the instructions here: http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080094634.shtml But now the outbound NAT doesn't seem to be working properly - it keeps going to the NAT of the Cisco, and not the designated IP address. If anyone can assist, I would appreciate it greatly. Let me know what you need, and I'll get it to you! Thanks!

  Read the article

• Remote Control Home PC from Corporate Work PC

  - by muncherelli

  Here is my situation: I am currently on a Windows XP workstation at work. I have an android tablet that I use to splashtop into my home PC. I would like to be able to use my work keyboard and mouse to control my home PC while I am splashtop'd into it using my tablet. My work PC is on a corporate LAN, and not on the same network as my tablet. The company I work for provides wifi for personal devices, but they are not accessable to the internal network. I thought about going the Synergy route, however that would require my home PC to be able to connect to my work PC which isn't really possible. The opposite would work though, if I could reverse connect the server to the client, but the Synergy software doesn't really support that. I do have a couple linux boxes running at home, so I can ssh into my home network and tunnel ports via SSH if needed. With what I have, how can I accomplish seamless keyboard and mouse sharing between my work PC and either my home PC or my android tablet?

  Read the article

• nginx automatic failover load balancing

  - by robinmag

  Hi, I'm using nginx and NginxHttpUpstreamModule for loadbalancing. My config is very simple: upstream lb { server 127.0.0.1:8081; server 127.0.0.1:8082; } server { listen 89; server_name localhost; location / { proxy_pass http://lb; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } But with this config, when one of 2 backend server is down, nginx still routes request to it and it results in timeout half of the time :( Is there any solution to make nginx to automatically route the request to another server when it detects a downed server. Thank you.

  Read the article

• ip routing policy in linux

  - by Dragos

  I have a linux system with two network interfaces (eth0 in x.x.x.0 and eth1 in x.x.y.0). Is there any posibility to add some route policy to send all the traffic to network x.x.y.0. I would like even the traffic from eth0 to be send to eth1's network. I cannot delete the direct connected networks from the routing table so all the traffic from x.x.x.0 network is send to eth0. I would like to send all traffic to eth1.

  Read the article

• Inbound connections using Internet Connection Sharing in Apple/Mac/Leopard

  - by tlianza

  I have a Mac mini which I'm using to give some other devices wireless access, by sharing it's Airport connection with the local ethernet, and that is plugged into a switch. All devices can get online no problem. (See how: http://www.macosxhints.com/article.php?story=20041112101646643 and http://www.macosxhints.com/article.php?story=20071223001432304 ) The issue is that I need to be able to connect in to these machines as well (at least, for the Slingbox to work). All the devices have 192.168.2.* addresses, and the rest of my local network is on 192.168.1.*. I tried setting a static route so that the 192.168.2.* addresses would use a gateway of 192.168.1.50 (my mac mini's address) but that didn't seem to help. Does anyone know if what I'm trying to do is possible? I admit I'm not certain what Internet Connection sharing is really doing under the hood... perhaps it just does basic nat, and doesn't do the type of routing I'm looking for. If so, anyone know if this is possible?

  Read the article

• Turn my machine in a hotspot/proxy

  - by Leonardo

  My workplace does not provide a wifi... only wired connection... but my machine has a working wifi card... is there a way to "bridge" my wired connection, making my iphone connect to it and use it as if the own machine is being used? (the idea is to make my machine provide a wifi-connection and route it through my wired connection) Details: My machine OS is win 2012 server I have full admin rights to my machine There is a corporate-proxy PS: If more details needed pls ask!

  Read the article

• is there such a thing as a ip femtocell, and what does it do?

  - by The Journeyman geek

  My dad mentioned a co-worker suggested using a device, that might use cdma to route calls through IP to save costs on a certain overseas project we're on- since our home base is quite far from there. I've never heard of such a device, so if it does, i'm wondering, if its specific to particular ISPs, or if you can just pick one off the shelf, plug it into an arbitraty internet connection, and make calls using it and a cellphone of some sort? As you can tell, details are sketchy, so... if such a device dosen't exist, saying so might be a right answer ;)

  Read the article

• How to proxy and encrypt all my internet traffic with Win7 and Win2008R2?

  - by Malartre

  I have a Windows 7 laptop and a Windows 2008 R2 server. How can I encrypt and route all my internet request from the Win7 laptop to the Win2008R2 server? I guess the server would be called a proxy? Goal is to prevent unencrypted network snooping. I found this article about using SSH, but I would prefer an official windows integrated solution. What's the Microsoft "way" on this? http://lifehacker.com/237227/geek-to-live--encrypt-your-web-browsing-session-with-an-ssh-socks-proxy I would like this to work for all internet traffic, not just browser traffic and I would like to set this up on many Win7 clients. Carl

  Read the article

• How can I use mobile network account at server so home sync works

  - by Mike Gallagher

  I would like to be able to use a mobile network account while sitting at my server. I had os x server 10.6 running on a mac mini server but recently got a new quad core iMac and want to take advantage of the extra power. My problem - I can sit at the server and log into the mobile network account but can not get it to sync back. When I attempt to sync it get error message that the afp share point is unavailable and that the files are hosted locally. My goal is to be able to use the new iMac as the server and set a user account so that it remains synced so when the account is accessed from other clients, particularly my macbook pro. Is mobile account the best route? Would an external account be a better option. Any advice or ideas of where to read up on this would be much appreciated.

  Read the article

• Fortigate VPN Routing issue

  - by user1571299

  I have 200B Fortigate unit with 2 internet WAN connections. I also have a remote site which I'm connected to via IPSEC VPN through WAN1. This site has only one GW IP address. I'd also like to setup a VPN ontop of WAN2 with that specific site as it's destination. The default route for my end is WAN1. My problem is I cant figure out how to have both tunnels up at the same time. What's the best practice for achieving this? Thanks

  Read the article

• Why can my Mac not connect to my iPhone via ssh?

  - by martin08

  I couldn't always ssh to my iPhone from my Mac. They're both on the same wifi network but sometimes the connection is established, sometimes it failed. From my Mac: $ ssh [email protected] ssh: connect to host 192.168.0.102 port 22: Operation timed out $ ping 192.168.0.102 PING 192.168.0.102 (192.168.0.102): 56 data bytes ping: sendto: No route to host ping: sendto: Host is down ping: sendto: Host is down I enabled SSH on the phone and am sure it can load webpages. So what might be a reason why they cannot connect? Thanks

  Read the article

• OpenVPN client on Amazon EC2

  - by Matt Culbreth

  I have an account with an OpenVPN service, and I'd like to get that running on my EC2 instance running Ubuntu 12.04. I have my config file in /etc/openvpn, and it connects fine when I run sudo openvpn --config matt.ovpn. However, I then lose connectivity to the EC2 machine, and I can't SSH back to it until I reboot. Previously I have done things like sudo ip rule add from IP_ADDRESS table 10 and then sudo ip route add default via GATEWAY_IP table 10, but that's not working on EC2. Any ideas? My private IP address right now is 10.209.29.XXX and my gateway is 10.209.29.1.

  Read the article

• Multicasting Windows 7 Image

  - by LawnChairSkank

  I am trying to deploy some new machines with windows 7 for the first time in our computer labs. We used to use third party imaging software and then run sysprep after the image was copied(XP), but it seems you can't go that route with windows 7. We set up a new imaging server with the windows system image manager, but when we try to multicast the image it pretty much takes down our whole staff and faculty network. I heard you can turn on a multicast feature on our cisco switches to help with the issue, but that it also slows the switches to a crawl. Another idea we have tried was pulling the the computer lab switch off the main network and plugging the imaging server directly into the computer lab switch so the multicast doesn't take down our network, but it doesn't seem to work without being able to hit a domain controller. Is there a way to multicast without taking out the network? I feel like I am missing something... Thanks in advance

  Read the article

• vmware workstation - virtual network adapters missing from ipconfig, still show in networking (XP host)

  - by Adam

  Hi Folks - here's a new one for me, and my first time posting here: I installed VMWare workstation 7.1 on a new PC. VMWare properly installs the virtual network adapters under the Network Connections control panel, however for some reason they do not show up under ipconfig, which is very weird. They also don't appear anywhere in "route print". I don't have network connectivity to the VM. My guesses are perhaps some conflict with Symantec AntiVirus or Symantec Client Firewall. Tried the following things: enabling TCP/IP in the virtual network adapters (they often get installed with it disabled for some reason) Restoring defualts in the VMnetcfg gui tool (this causes an uninstall and reinstall of the virtual network adapters on the host) Re-installing vmware workstation Uninstalling checkpoint secureremote and then reinstalling vmware Just to be clear, this problem is totally on the host. In my searching for stuff about (non-vmware) adapters missing from ipconfig, I see some posts about resetting the TCP/IP stack using netsh. Looking into that next... Thanks!

  Read the article

• Looking for advice on Hyper-v storage replication

  - by Notre1

  I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

  Read the article

• MS project publishing to TFS web portal display

  - by denis bastarache

  So, when we initially created our MPP schedule, I made use of indends / subordinates to break down the project by the various stages of the lifecycle, which is fine... no issues there... But now that I'm trying to publish this over to TFS display, it'll only pick up the actual "action items / sub-tasks" seeing as I have resource allocation specified. So for example I have an "Analysis" phase with a few items underneath, and "System Requirements" phase with the same items, so when I publish these to TFS, it won't display the "Parent" distinction between items, so both "Tasks" instances are being published in TFS under the exact same name... So, if I can't do this Automatically, I'll likely have edit each tasks with "Analysis - Item 1", "Analysis - item 2", "SRD - Item 1", "SRD - item 2"... is there a way to do this automatically, or will have to go the manual route??

  Read the article

• Make BIND use DHCP DNS as backup

  - by cainmi

  I run BIND locally on my OS X machine, to enable wildcard Apache vhosts, which requires setting the DNS server for all network interfaces to 127.0.0.1. This works great, but means when I am on a network which uses an internal DNS server to route special (i.e. .companyname) URLs to a server on the network, the lookup fails. I tried adding both 127.0.0.1 and the DHCP provided DNS server, but this doesn't work either. Is there a way to make BIND use the DHCP DNS server for requests it cannot resolve locally?

  Read the article

• Can I use the Airport Express as a an uplink between two networks?

  - by Ant Swift

  I have two separate networks using different IP ranges, 192.168.0.* for the wired only, isolated network and 192.160.1.* for the wireless only network which is connected to the internet. The wired network has a network printer setup and working and I want to be able to share it out to members of the wireless network (see diagram below). In short I need some kind of uplink between the two networks. Currently running a cable is out since there is no suitable route. I have a spare Airport Express and I am wondering if I could attach it to the wired network and have it join the wireless and act as the uplink between the two. Anyone know if the device is capable of this?

  Read the article

• How to register a new domain name on a windows based domain controller?

  - by JL

  Is there an easy and quick way I can create a new subdomain on a windows based domain controller. My primary domain controller is also my primary DNS server on my network. I want to create a subdomain and have its ip directed to that of my IIS server. Thanks in advance... Sorry if my terminology is somewhat lacking... My domain is companyName.com What I want to do is create auditingResults.companyName.com... and have it route to 192.168.1.3 for example..... where on 1.3 I will have an IIS server presetup. Please feel free to leave comments to correct my terminology if required....

  Read the article

• Windows Proxy Server advice

  - by Scott

  I have a webserver that currently has about 10 IP addresses. I have various clients that require a proxy server to route their internal traffic through. The load is not that great, so I'd like to have this ONE server act as a proxy server for 10 different clients, each client having their own unique IP on the server. The hardware is already setup, but I'm wondering what software solutions you guys recommend? I've looked at WinGate, Squid-Proxy, etc...but am pretty green with this. Maybe there's even a way to have Windows do this natively? I'm running Windows Server 2008, 32 bit.

  Read the article

• CentOS send mail with external SMTP server and without local daemons

  - by Vilx-

  I've got a little old server with CentOS 6.5 on it. The hardware is old and crappy, but enough for what it has to do. Which consists of SSH (+SFTP), Apache, PHP and MySQL. Still, I'm trying to cut away all that I can. One thing that it does not need to do is to be an SMTP server. There are no mailboxes on it and nobody will ever route mail through it. However I do want it to send me an email when something goes wrong. Also, the webpages will send emails from PHP. So that brings me to the question - can I set up the mail system in such a way that there isn't an expensive mailer daemon sitting in the background with queues and whatnotelse, but rather every email is directly and immediately delivered to an external SMTP server? And how do I go about it?

  Read the article

• Connecting via ShrewSoft VPN client means no LAN internet access (Windows 7 64 bit) - any advice please?

  - by iwishiknewmoreaboutnetworking

  I have a Windows 7 64 bit desktop machine which is connected to a LAN. I recently installed ShrewSoft VPN client v 2.1.7 on my machine so that I can connect to a license server hosted by my customer. They are running a Cisco VPN server and I originally tried (unsuccessfully!) to use the Cisco VPN client for Windows 64 bit but the default gateway wasn't being configured correctly after loading in my pcf file. Using ShrewSoft I am able to import the same pcf file, and successfully connect to the machine I need to using the VPN client software. The client machine I need to connect to has IP address 1.52.90.33. The problem is that when I am connected to the customer network using the VPN client application (and after a few minutes) I lose my LAN internet connection. I can only presume that this is because, by default the ShrewSoft VPN client application automatically tunnels all traffic through the VPN connection. I know there is an option to switch off the "Tunnel All" option on the Policy tab of the application and enter a Remote Network Resource (to "Include" or "Exclude") as "Address" and "Netmask" IP addresses however I am not sure what I need to enter here. Here is my ipconfig output before connecting to the VPN (with suffixes blanked out): Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : ***.*** Link-local IPv6 Address . . . . . : fe80::8de3:9dbe:393a:33ba%11 IPv4 Address. . . . . . . . . . . : 150.237.13.17 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 150.237.13.1 Tunnel adapter 6TO4 Adapter: Connection-specific DNS Suffix . : ***.*** IPv6 Address. . . . . . . . . . . : 2002:96ed:d11::96ed:d11 Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301 Tunnel adapter Local Area Connection* 9: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:2cf9:38c4:6912:f2ee Link-local IPv6 Address . . . . . : fe80::2cf9:38c4:6912:f2ee%12 Default Gateway . . . . . . . . . : Tunnel adapter isatap.***.***: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : ***.*** Here is my route print output before connecting to the VPN: =========================================================================== Interface List 11...20 cf 30 9d ec 2a ......Realtek RTL8168D/8111D Family PCI-E Gigabit Ethern et NIC (NDIS 6.20) 1...........................Software Loopback Interface 1 14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter 12...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 150.237.13.1 150.237.13.17 2 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 150.237.13.0 255.255.255.0 On-link 150.237.13.17 257 150.237.13.17 255.255.255.255 On-link 150.237.13.17 257 150.237.13.255 255.255.255.255 On-link 150.237.13.17 257 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 150.237.13.17 257 255.255.255.255 255.255.255.255 On-link 12

  Read the article

• Routing between two VLANs on Single Dell 6200 Switch

  - by jenglee

  I want to be able to route between two vlans that I have created and I am not sure how to go about it. So I have created, VLAN 5 with IP Address 192.168.5.1/24 and VLAN 10 with IP Address 192.168.0.1/24 //main IP addresses that I use. How would I be able to get (for example) the IP Address 192.168.0.144 to see any ip addresses in 192.168.5.1/24? Also do you have to set a default gateway for each VLAN or do you set the default gateway for the switch.

  Read the article

< Previous Page | 130 131 132 133 134 135 136 137 138 139 140 141  | Next Page >