Search Results

Search found 17476 results on 700 pages for 'boot manager'.

Page 135/700 | < Previous Page | 131 132 133 134 135 136 137 138 139 140 141 142  | Next Page >

• Make UEFI, GPT, Bootloader, SSD, USB, Linux and Windows work together

  - by user129552

  I like to use the latest hardware and the latest software; thus I have a Laptop (Lenovo X220) with UEFI instead of BIOS an SSD instead of an HDD GPT partitioning scheme instead of MBR USB to boot from instead of optical disks. I need to use both Windows and Linux. I tried to make them work alongside, but I didn't succeed. Most Linux distribution isos don't even really work on UEFI systems booted from USB. (Not even the self-claimed cutting-edge Fedora. I also tried Linux Mint Debian Edition and Sabayon Linux (according to this guide) which did not work. Only Ubuntu worked for me. I first installed Windows 8 which created sda1: Recovery, sda2: EFI system, sda3: msftres, sda4: NTFS Windows. Windows worked without a problem. I then created sda5: linux-swap and installed Ubuntu into sda6: btrfs. After rebooting, I was not presented GRUB2 as expected, but instead my system just booted into Ubuntu. I could no longer access Windows. After fixing dpkg in btrfs Ubuntu, I followed the Ubuntu documentation on UEFI booting. The result left me with a broken GRUB2, but interestingly, when I wanted to select the device to boot from, I was not only presented the internal SSD, an attached USB device, or LAN, but also Grub2 (broken), Ubuntu and Windows. The result is not very satisfying to me. What would I have to do to fix everything? Or differently asked, what operating system should I install at what point given my possibilities and requirements, so that I have a working bootloader in my UEFI GPT system which presents me a working Linux and Windows.

  Read the article

• BIOS not detecting working SATA hard drive

  - by user28927

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• Unable to load Windows after using EasyBCD to Reset bcd [duplicate]

  - by johnny

  This question already has an answer here: How can I repair the Windows 8 EFI Bootloader? 9 answers My windows installation was working perfectly fine until i clicked "Reset BCD" in EasyBCD in Windows 8. After clicking that EasyBCD told me to add Win 8 entry via Add Entry Menu so i did. After restart, win 8 would not start. Neither would recovery F11. Attempts i made to Restore : Ran boot-repair from ubuntu live cd several time. Used Win8 system recovery disc created via virtualbox with win 8 preview iso. Automated repair from Win8 system recovery disc Ran following commands from cmd started from Win8 system recovery disc bootrec /fixmbr Result : Success message bootrec /rebuildbcd Result : after hitting (Y) "The requested system device cannot be found" System refresh started from Win8 system recovery disc gives error that device is locked. System reset started from Win8 system recovery disc gives error that required partition or device is missing or not accessible. Used automated repair from EasyRE disc. It gave success message. Used Fix boot problem from Macrium reflect winPE repair disc. Copied Recovery partition to usb. Booting from usb gave this error Your PC needs to be repaired. Error Code : 0XC000000f Press Enter to try again Press F8 for Startup Settings F8 & Enter does nothing I cannot install WIn7 or Win 8, error it gives : "windows cannot be installed on this disk. The selected disk is of the GPT partition style."

  Read the article

• Creating a bootable USB drive from a distro split over two DVD ISOs

  - by Kev

  I am searching and not finding the right way to do this. Please note, I don't think I'm trying for anything strange here. I just want to make a bootable USB stick of a single OS that happens to be larger than one DVD and happens to be larger than FAT32 will allow for in a single file. On our slow connection I spent a long time downloading CentOS 5.9's two DVD ISOs: CentOS-5.9-x86_64-bin-DVD-1of2.iso (4.4 GB) CentOS-5.9-x86_64-bin-DVD-2of2.iso (718 MB) I have a USB stick that I want to somehow get these two ISOs on. Since the first one is 4.4 GB, I can't use ISO2USB because it insists on FAT32. I cannot find an alternative that lets you specify more than one ISO image--of the same distro, I'm not trying for some fancy multi-boot thing--to put on the same stick. I guess I should have downloaded the CD ISOs, but I thought I was "saving time" because then I wouldn't have as many files to run through the md5 checker. There's no IMG file of the whole thing (only a net install version, which I don't want--I want to pre-download everything) otherwise I would've gone for that. So, given that I have these two DVD ISOs, how can I get them on a stick that will boot and make use of both of them properly to install CentOS somewhere? Again, I don't think this is anything out of the ordinary, yet I can't find software/docs that seem to support this. Am I stuck re-downloading everything in CD-sized ISOs just to do this? I found this, but it doesn't run on Windows. I am using Windows to prepare the stick.

  Read the article

• Imac g5 with no OS nor CD drive

  - by sinekonata

  What I want: Ubuntu on a g5 Imac. What I have: An empty PC (Intel g5 17" Imac) with broken CD drive. Its model is A1173. This PC with Ubuntu 12.04 and an old Vista partition. a usb flash drive. Problems: No CD means the only boot Drive I could use is USB. There are no BIOS on Macs so I can't set boot settings or even see if it detects my USB drive. When I start the machine and press ALT the first and only thing I see is an old corrupted winXP partition and not a single option or additional information. So assuming blindly that the Mac hardware/firmware works normally, I don't have any Mac OS to use any of the tools that I found on different tutorials for building a bootable .img drive for macs. I can't find much software on Linux/Windows to substitute to those tools, for example among others converting an .iso file (win/linux) to .img (mac I guess). Which makes me think that the scenario where someone like me has Mac hardware but no Mac OS is extremely rare. So other than finding someone that has a Mac I have no solution. So I ask what would you do? the only thing is it should not involve any money (I know mac soft is rarely free) which also excludes getting any MacOS unless I can use a free macos.img for VM or restore the original Mac for free. Thank you

  Read the article

• Gigabyte H55N-USB3: No video on HDMI

  - by newt

  I built a new PC with a Gigabyte H55N-USB3 / Intel Core i5 650. With a monitor plugged in the DVI port, everything works fine. I installed Windows 7 32-bit and enabled remote desktop connection. After that, I unplugged the monitor, plugged it into network and installed everything else (drivers, programs, etc) via RDP. However, when I try to use the HDMI port on my TV nothing appears. Neither during the boot, neither after Windows starts. The TV says there's "no signal" (if I remove the cable the message changes to "check cable"). The cable is new, and it is working fine with my home theater on same TV (by the way, it is the cable which came bundled with the home theater). Video driver is the latest from Intel site. Anyway, this shouldn't be the problem since there is no image during the boot. Any ideas or tips would be welcome. I'm googling around but found nothing useful, yet.

  Read the article

• DVD-burner disappears when using grub

  - by drblah

  This is a rather annoying problem I have with Linux on my laptop. Whenever I install any Linux distro that relies on grub (which is about 99 % apparently) it will mess up my DVD-drive and the drive will not be recognized after booting, no matter the OS (Ubunntu, Arch, Windows Vista or 7). I know the problem has nothing to do the DVD-drive itself, because I bought a new one a few months ago. I am also sure that grub is messing the drive up, because I have tried to use LILO, which worked fine (except for horrible boot times.) This problem have persisted through about 3-4 years and it is a pretty bad show stopper whenever I want to work with Linux. I had hoped it would get fixed over time, but no one seems to have the exact problem I have. The drive is connected with an IDE connection. Update: The old drive was a Toshiba Samsung SN-S082. I don't know the model number of the new one, but it is HP (I think). Things I have tried to fix it: Mess about with some BIOS settings like enabling AHCI and change some IDE settings. Installing a different boot loader DOES fix the problem but I would like to use grub.

  Read the article

• How to reinstall bootloader after migration to SSD

  - by hijarian

  I must say, it was difficult to name this question. Basically, I need to properly reinstall the bootloader on my system, because I already have the working system disks for my OSes. The long story is this: I had the large slow HDD with Windows7 & Debian Wheezy dual-boot on it, perfectly bootable. Then, I ordered the SSD drive and prepared my system partitions to fit onto the much smaller SSD. I wanted the following schema: 128 GB Windows 24 GB / on Debian 86 GB /home on Debian Strange size for /home because there's no such thing as true 256GB disk drive. So, I've prepared such a partitions on my initial HDD and installed the new SSD and then I loaded the GParted live USB (can't remember now how it was really named), and then just copypasted the partitions from HDD to SSD. So, now I have the following partitions across the physical disks: SSD 128 GB copy of original Windows partition 24 GB copy of presumably Debian / 86 GB copy of presumably Debian /home HDD 128 GB Windows 24 GB / on Debian 86 GB /home on Debian ... several other partitions with non-system data ... And the behavior of the system right after the Ctrl+C, Ctrl+V in GParted was as follows: no GRUB, system boots right into the Windows on HDD. In BIOS settings are to boot from SSD first. I managed to create the Debian Testing installation USB and loaded it into the rescue mode, found that it identified my SSD as /dev/sda and installed the GRUB to the /dev/sda. Now my system loads the GRUB which lists both Windows and Debian. From HDD. So, I am now back into initial position. Please, how I should set up the GRUB so it'll load the OSes correctly from SSD? Should I fire up my Debian, fiddle with the GRUB's config and reinstall it again to the same place (at SSD)?

  Read the article

• Ubuntu+Win7--disk error press any key to restart

  - by Siddharth

  Apparently,none of the solutions in any other posts and forums worked for me For some reasons I decided to remove ubuntu from my hard disk drive. My partition table(presently): (/dev/sda1) (fat32) 900 MiB ---(MBR,I suppose) (/dev/sda2) (ntfs) 70 GiB -----(Windows 7) (/dev/sda3) (ntfs) 314.88 GiB --(Personal File storage) (/dev/sda4) (ext4) 80 GiB -----(Ubuntu 13.04) (unallocated) -----1.31 MiB So,after moving(cut-paste) everything(for backup) from the fat32 partition using win7..I booted into Ubuntu and copied the remaining 3 files(hidden in Win7 file explorer) --bootmgr,bootsect.bak,and one more which I do not remember.TERRIBLE MISTAKE After this I again booted into Windows and deleted ext4 partition..formatted it to ntfs..and shut down the pc.Then,I put in a Win7 bootable USB..using command prompt I entered bootrec /fixmbr,and bootrec /fixboot.. Restarting showed me the GRUB..choosing windows 7 showed me "Disk Error. Press any key to restart." I also installed a fresh Win7 installation on the 80 GiB partition expecting a Windows Legacy Bootloader with two win7 options..but did not work. Then..I used a Ubuntu LiveUSB to put it back to the present configuration(above) since all methods to restore the MBR failed.. I copied back the fat32 partitions backup files but couldn't copy those 3 files.Somehow ,they had been recreated and were non-replaceable. I do not want to format the win7 partition for a fresh one. I have used boot-repair..Restore MBR option brings back to "Disk error...." without even going through grub..so I reinstalled grub and I'm able to boot into Ubuntu. grub menu shows the win7 option as "Windows 7 (loader) (on /dev/sda1)". paste.ubuntu.com/5753710 paste.ubuntu.com/5775999

  Read the article

• Installed Windows 7 Ultimate on D Drive and previous Windows 7 Enterprise on C Drive has stopped starting up

  - by teenup

  Please please help! I have installed Windows 7 Ultimate on same hard drive on D Drive on my laptop and the previous Windows 7 Enterprise which was installed on C Drive is not booting up now. When I turn on my laptop, I see two Windows 7 on the screen, when I select newer one, it starts, but when I select older one which is Enterprise edition, system won't start and I get the DOS black screen with this error message: Windows Boot Manager Windows failed to start. A recent hardware or software change might be the cause. To fix the problem: Insert your Windows installation disc and restart your computer. Choose your language settings, and then click "Next." Click "repair your computer." Info: The boot selection failed because a required device is inaccessible. I notice that when I run the newer OS installed, the previous OS's drive (Which is D: now instead of C:) has become unusable and when I double click it, it asks me to format the drive. The data, that I had on my D Drive (Which is now C Drive for new OS), I had copied it to a network path and it is available. It was containing Windows 7 Users folder which I copied at that time when installing new windows. I have copied that Users folder again to the new OS's C Drive thinking it would run again, but of no use. Please please please...if someone can help...It is extremely required for me. Thanks a lot in advance.

  Read the article

• Encrypted Windows 7 & Linux Advice Wanted

  - by Miles

  I would like to set up my laptop to dual boot Arch Linux and Windows 7 with file sharing and encryption. Just wanted some advice on going about this because I have not dealt with encryption nor file sharing. I have two 500GB hard drives, and this is my plan: Install Windows 7 across both hard drives Use a live CD to wipe out Windows boot loader and replace with Grub Legacy Use live CD to wipe out second hard drive and re-size the Windows partition located on first hard drive Install Arch Linux along side with Windows 7 on first hard drive, all remaining space goes to home folder as ext2 Install truecrypt and ext2fsd Concerns: Is this the most efficient way to share files between both OSes? Or should I just be using NTFS to store all my data? How would the file permissions work when sharing files between Windows and Linux? Is there a high likley hood of corruption, and what is the ease of backing up files from an encrypted disk? Anything I should look out for, conflict between Grub and Truecrypt? Thank you for any advice, and feel free to post any links you might find useful to me. I am trying to plan this out so I can minimize downtime as I do not want to spend more than a night on this, nor do I want to run into a major problem some time in the future.

  Read the article

• 64-bit Windows 7 gets stuck on logo screen on bootup

  - by Richard B

  I've had a PC running Windows 7 in my office which I'm not using at the moment (cause I'm working elsewhere as a consultant atm), I'm only accessing the PC using Team Viewer (http://www.teamviewer.com/) which means the PC has been running for quite some time now. I've restarted it maybe twice a week though. A few days ago I couldn't access it using Team Viewer and when I got to the office the screen was black with only the mouse pointer showing. The PC has four hard disks, three of them (all 1Tb) is using RAID 5. This is what I've done so far: I reboot and everything seems to load correctly. I get to a screen that gives me two choices - boot Windows normally or perform a startup repair. Choosing to boot Windows only gets me to the Windows 7 logo screen which only animates over and over again. Choosing to repair gets me to the repair screen that "checks for problems" and then it gets stuck on the "Attempting repairs..."-screen (I let it run for about 24 hours before giving up). What is the next step to take? I don't have any backups and no system restore points saved. I can access files and folders through a terminal window using a Windows 7 DVD so I guess nothing is lost yet... Please help me, thanks!

  Read the article

• Is my motherboard failing, or is there some other issue?

  - by ThatGuy

  So, several months ago I put together my own desktop PC. I set up a dual boot to Windows and Ubuntu. Recently, without changing any settings or installing anything new, the wifi stopped working on windows (I use a wifi adapter). It said it was connected, Network settings showed that it was working and running trouble shooting had no results. My internet still works on any other device. I found that removing the adapter from the motherboard and plugging it back in was the only thing that fixed the problem. Reinstalling the wifi drivers did not help. I purchased a new Wifi adapter, but the problem persists. More recently, I had a much more discouraging development. Sometimes, turning on the computer results in a boot loop: BIOS never starts. Instead, the monitor turns on as if it got a signal, then immediately turns off. This loops on it's own indefinitely until I hold down power, hard reset it, and try again. Sometimes it works, sometimes it doesn't. I haven't tested much on the Ubuntu side. It appears that wifi works at least some of the time, but since I've had issues just getting to BIOS I'm not confident the issue is on the software side. I've also noticed issues with some of the USB ports no longer working, but that seems to be off and on. Finally, as of a few minutes ago, I booted to windows to discover that everything was running very slowly. Slow here is a relative word, but I have a Samsung 840 pro SSD and I'm used to applications running nigh instantly, and it was a solid 3 minutes before any of my applications would load. Anyway, my question is this: Is it likely that my motherboard is failing? Either way, what steps can I take to try and pin down the problem and figure out what to do?

  Read the article

• Windows 7 not booting up and stuck at startup repair

  - by mikimr

  I've been having issues with Windows 7 Home Premium on a Lenovo laptop. At first, it would not start up normally at all. I started it in Safe Mode, where I disabled all non-MS services and tried again to no avail. It then goes into Startup repair where it failed several times. I tried copying the original registry settings, still the same. I resorted to booting with an Ubuntu DVD, where I ran the boot-repair, where it is supposed to correct the Windows boot. No luck. I used Win7 DVD to start up from there, where I had the option to install or repair. I chose the repair, got into command prompt, ran chkdsk /i /r, where it found 3 unreadable segments, went through the 2nd step without issues, and the 3rd step completed with some errors (can't recall the exact errors). When I restarted the machine, it went to straight to the Stratup Repair, indicating "Attempting repairs... Repairing dis errors. This might take over an hour to complete." It's been like this for nearly 15 hours. When I try to cancel or close the Startup Repair window, I get a message "The current repair operation cannot be cancelled." Should I let it run or force shut the machine? If force shut, how can I resolve this problem? Thanks.

  Read the article

• Bootable ISO to USB stick xp quickest method

  - by brux

  My dog took a leak on my PC when I went out (ye funny), now it reandomly restarts - I'm convinced the HDD is failing because the Windows seagate diagnostic program fails on a few tests. I want to run this prior to windows in an attempt to try and recover sectors, the program includes an iso which can be written to cd and booted, but i dont have any cd's. I tried using unetbootin to create the bootable usb from the iso file (SeaToolsDOS222ALL.576.ISO) but it doesnt work. When i boot from the usb hdd unetbootin loads with "default" in the menu. No joy booting though. I checked the usb hdd in windows and all the files are there, extracted from the iso file, wont boot though. Any ideas? Im using windows xp. More info - when the computer restarts (like i just did now) it constantly reaches the end of POST and then restarts in infinite loop. If I pull the power cable out it will get back into windows, the longer i leave it between attempts, the longer I am able to stay in windows until it restarts. i.e if i leave the power cable out 5 minutes it will stay operable for longer than if i had left it out for only a few seconds.

  Read the article

• Oracle Linux screen freezes during installation

  - by Fearless

  I was installing Oracle Linux 6.4 on a server, and the screen suddenly froze. Here were the previous steps: I put in the disk, clicked install, checked the disk (no errors), did pre-install setup (clock, root password, host+domain name, etc.), configured two 40GB hard drives in a RAID1 array (no swap, 3100mb encrypted raid partitions, ~100mb ext4 partition mounting to /boot, encrypted ext4 RAID device with mounting to /), selected packages, hit continue. The system did its short preinstall processes, then when to the main installation screen with the long status bar. The installer proceeded like always, but around package 250 out of ~1000, the screen suddenly went black with a text cursor in the upper left corner of the screen and the mouse cursor in its previous place. Neither cursor moved and the only thing that triggered a response was a ctrl-alt-delete that rebooted it. I have run this in VMs before without this issue. Memtest hasn't reported anything, and the media check went smoothly. The machine has supported Ubuntu server without issues before. Any ideas? I have tried booting after that, but the grub bootloader tries to find fd0 for some reason (I have no idea why it would search for the floppy disk). UPDATE My server successfully installed, but won't boot up. I think that, for some reason, it is still using the old bootloader from the previous installation. Any ideas on how to fix that?

  Read the article

• Windows xp blinking under score after bios

  - by heyjoe

  so this is for an older pc I have to repair for a friend. The pc has an hdd of about 60 something gb, It uses win xp and let's say 60-70% of the boots it hangs on showing only an underscore bilking line after bios screen, rest of the times it boots fine or the computer shuts down on xp loading screen. Sometimes if you let it alone while the underscore is blinking, it will boot after a while, like a few minutes, some times it won't boot at all even if you give him more time, like one hour. When it boots successfully the pc seems to work fine. I think it's a bad hard disk and i'm about to suggest buying a new one and switching it but I don't have enough experience and i would hate making him buy a new hdd and not solving the problem. anyone has any tips? I know there are other topics about blinking underscores or cursors while xp is booting but the issues about the pc shutting itself down or sometimes booting really freaks me out. Can't format everything and re install until about 10 days from now, cause the dude has some program for his business on this pc and I have to migrate it when the next computer arrives, however he needs to use it until then. so please advise, thx.

  Read the article

• Burning Linux ISO to DVD and making it bootable.

  - by toc777

  Hi everyone, I just downloaded the Fedora 14 Live-Desktop ISO and used CDBurnerXP to burn the image to a DVD. For some reason the first time I burned the image nothing showed up on the DVD when I accessed it even though CDBurnerXP said it had successfully burned to the disk. I did it again and the ISO shows up on the disk (I don't think this is right, should it be the files inside the image that show up on disk or the image file??). The problem now is my dell PC can't find the ISO when I try to boot from it. I get an error saying it can't boot from the CD. I have verified the ISO image as directed from the Fedora website. My question is how do I make a bootable CD from a Fedora Live-Desktop ISO? How can I verify that the ISO was written to the CD correctly and has anyone had any issues booting from a CD using a Dell desktop (I'm not at home at the moment so I can't check what model it is but its old enough, I've had it for about 5 years). EDIT: All that needed to be done was to burn the image to CD as an image and not a data file. The first three times failed, I'm not sure if this was because of faulty DVD's or if the write speed was too high (16x). I put in a new DVD and changed the write speed to 8x, the image was then properly burned to the disk without any errors. Thanks.

  Read the article

• Lenovo Thinkpad T430 not booting from HDD if there is a USB modem connected

  - by user93353

  I have a T430 Levono Thinkpad running Win7. I use a ZTE USB modem (something like this) for my internet connection. I usually keep the modem plugged into the USB drive even when the laptop is shutdown or hibernating. This worked fine on my earlier laptops. But with the Lenovo, my laptop doesn't boot if the modem is in the USB drive. It shows the initial character based screen where it gives the Thinkpad message & BIOS details and then waits. If I pull out the modem, it goes ahead. I have disabled USB as a boot option in my BIOS settings, but even then this happens sometimes (but not all the times). Likewise while resuming from hibernation. The USB modem also has drivers & ISP connection client which getting installed the first time you use it on any machine. I have used multiple laptops (HP, DELL, Acer, Gateway) but never faced this problem before. I have friends who use other Thinkpad models but haven't faced this issue. Any resolutions, workarounds for this?

  Read the article

• Multiboot USB (OSX only): How to customize partition name?

  - by wrk2bike

  Trying to deal with all the Mac OSX recovery disks I've got by moving them to bootable USB images. I've got a big USB drive with multiple partitions for each recovery disk, and it's easy to use Disk Utility to "restore" the recovery DVD to a partition. When I boot my target Mac while holding down the Alt key, I can see all my bootable images and they work great. Problem is, they've all got the same name: "Mac OS X Install DVD." I manage Macs of various vintages. If my target Mac needs 10.6.3 for example, my only option seems to be to try each one until I get past the "Mac OSX can't be installed on this computer" message. I originally named my partitions with the OSX revision number, but that name is replaced by the disk image name during Disk Utility restore. Is there any way to customize the name during or after Disk Utility restore? I tried making a new DVD image on disk first and renaming it, but when I restore it to my recovery partition it has the original name. EDIT: After booting to the wrong partition, and getting the "..can't be installed" message, I can open the Startup Disk menu and see the other partitions - and as I select each one, the info at the bottom indicates which OS revision is on that partition. So I know the info is in there! Just want it at the boot screen if possible.

  Read the article

• Shrinking windows and recovery partitions on the samsung new series 9

  - by bobbaluba

  I just bought a samsung NP900X3C, and as I was going to install linux, I noticed the windows partitions and recovery partitions occupied a major portion of the disk. The disk is a 128 GB SSD, and I want to keep the windows partition in order to play some games once in a while, but the windows disk is already 45GB full (with no installed programs) and the recovery partition is 20GB. That leaves under 60 GB for linux, which is not optimal, since that is what I'm going to be using most of the time, and there would be no room for games on the windows partition. There are also two small partitions that I don't know what are doing, one 100mb at the start of the disk that I'm guessing is some kind of boot partition, and one 5GB, that is described as an OS/2 hidden C: drive What I'm wondering is: can i delete the recovery partition? What about the mystical 5gb partition? Here is what fdisk reports: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 128.0 GB, 128035676160 bytes 255 heads, 63 sectors/track, 15566 cylinders, total 250069680 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x83953ffc Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 198273023 99033088 7 HPFS/NTFS/exFAT /dev/sda3 198273024 207276031 4501504 84 OS/2 hidden C: drive /dev/sda4 207276032 250068991 21396480 27 Hidden NTFS WinRE

  Read the article

• josso newbie setup problems - can't use tomcat's manager page

  - by opensas

  I'm trying to setup josso on an apache tomcat server running on windows. I've installed Apache Tomcat/6.0.26 fro zip file to c:\tomcat then installed josso following the documentation at http://www.josso.org/confluence/display/JOSSO1/Quick+Start started tomcat with c:\tomcat\bin\startup.bat, and noticed the following warnings ADVERTENCIA: [SetPropertiesRule]{Server/Service/Engine/Realm} Setting property ' debug' to '1' did not find a matching property. 21/03/2010 15:55:03 org.apache.tomcat.util.digester.SetPropertiesRule begin ADVERTENCIA: [SetPropertiesRule]{Server/Service/Engine/Host/Valve} Setting prope rty 'appName' to 'josso' did not find a matching property. ... ADVERTENCIA: Unable to find required classes (javax.activation.DataHandler and j avax.mail.internet.MimeMultipart). Attachment support is disabled. ... ADVERTENCIA: Bean with key 'josso:type=SSOAuditManager' has been registered as a n MBean but has no exposed attributes or operations ... but then everything seems to work fine, the problem is I can no longer access http://localhost:8080/manager/html using user tomcat /tomcat, as configured in \conf\tomcat-users.xml (before installing josso it worked) I tried with tomcat/tomcatpwd as defined in \lib\josso-credentials.xml and even added tomcat and the manager role to \lib\josso-users.xml, with no luck... Is anybody having the same problem? how can I access tomcat's manager page? Thanks a lot saludos sas This is my config: C:\tomcat\bincatalina version Using CATALINA_BASE: "C:\tomcat" Using CATALINA_HOME: "C:\tomcat" Using CATALINA_TMPDIR: "C:\tomcat\temp" Using JRE_HOME: "c:\java" Using CLASSPATH: "C:\tomcat\bin\bootstrap.jar" Server version: Apache Tomcat/6.0.26 Server built: March 9 2010 1805 Server number: 6.0.26.0 OS Name: Windows XP OS Version: 5.1 Architecture: x86 JVM Version: 1.5.0_22-b03 JVM Vendor: Sun Microsystems Inc ps: moreover, when shutting down, I get a couple of error like this GRAVE: A web application appears to have started a thread named [JOSSOAssertionM onitor] but has failed to stop it. This is very likely to create a memory leak. 21/03/2010 15:57:06 org.apache.catalina.loader.WebappClassLoader clearReferences Threads and then tomcat's shutdown freezes at 21/03/2010 15:57:07 org.apache.coyote.ajp.AjpAprProtocol destroy INFO: Parando Coyote AJP/1.3 en ajp-8009 ps: sorry for this lengthy question...

  Read the article

• Windows-mobile app won't run after being closed by Task Manager

  - by pithyless

  I've inherited some windows-mobile code that I've been bringing up-to-date. I've come across a weird bug, and I was hoping that even though a bit vague, maybe it will spark someone's memory: Running the app (which is basically a glorified Forms app with P/Invoke gps code), I switch to the task manager, and close the app via End Task. Seems to exit fine (no errors and disappears from Task Manager). Unfortunately, the app refuses to start a second time until I reboot the phone or reinstall the CAB. What's worse: this bug is reproducible on a HTC Diamond, but works fine (ie. can run again after EndTask) on an HTC HD2. The only thing I can think of is some kind of timing race between a Dispose() and the Task Manager. Any ideas? I'm also thinking of a workaround - I do have a working "Exit Application" routine that correctly cleans up the app; can I catch the EndTask event in the c# code in order to complete a proper cleanup? Maybe I'm just missing the pain point... all ideas welcome :)

  Read the article

• JPA - Performance with using multiple entity manager

  - by Nguyen Tuan Linh

  My situation is: The code is not mine I have two kinds of database: one is Dad, one is Son. In Dad, I have a table to store JNDI name. I will look up Dad using JNDI, create entity manager, and retrieve this table. From these retrieved JNDI names, I will create multiple entity managers using multiple Son databases. The problem is: Son have thousands of entities. It takes each Son database around 10 minutes to load all entities. If there is 4 Son databases, it will be 40 minutes. My question: Is there any way to load all entities and use them for all entity manager? Please look at the code below For each Son JNDI: Map<String, String> puSonProperties = new HashMap<String, String>(); puSonProperties.put("javax.persistence.jtaDataSource", sonJndi); EntityManagerFactory emf = Persistence.createEntityManagerFactory("PUSon", puSonProperties); PUSon - All of them use the same persistence unit log.info("Verify entity manager for son: {0} - {1}", sonCode, emSon.find(Son_configuration.class, 0) != null ? "ok" : "failed!"); This is the actual code where the loading of all entities begins. 10 mins.

  Read the article

• Integrating HP Systems Insight Manager into an existing environment

  - by ewwhite

  I'm working with an environment that spans multiple data centers/sites and consists primarily of HP ProLiant servers (G5-G7) running Linux. The mix is 30% RHEL/CentOS, the rest are Gentoo :(. I also have a few dozen virtual machines running back-office and Windows servers on VMWare ESX hosts. I run OpenNMS to pull SNMP data from the various server nodes and networking devices. While OpenNMS works wonderfully for up/down, thresholds and notifications, it's native handling of traps is a little rough and the graphs are not particularly pretty. I use Orca/RRD graphs for performance trending and nice graphs. I'm tasked with inventorying the environment and wanted to come up with a clean way to organize server information. Since my environment is mostly HP, I've been playing with HP Systems Insight Manager as a way to extract server data and to deploy HP health/monitoring packages and firmware. The Gentoo systems eventually have to be converted to CentOS, so getting a quick assessment of what hardware is where would be great. Although I've read through a few hundred pages of HP manuals, I'm having a difficult time understanding how to get HP SIM to do what I want, though. My main problems are: I have about 40 subnets to deal with; 98% connected with private lines to facilities across the globe. I don't want to initiate an HP SIM discovery only to pull back every piece of intermediate networking hardware and equipment from all of the locations. I'd like this to focus on the servers. I have OpenNMS configured to accept traps. I don't want HP SIM to duplicate that effort. It seems like the built-in software deployment tool wants to overwrite the trapsink parameters for the systems it encounters during discovery. I have about 10 administrative username/password combinations in use across this infrastructure. Is there a more efficient way to get HP SIM to do the discovery or break discovery into manageable chunks? In terms of general workflow, do people typically install the HP Management Agents during the initial OS deployment (e.g. kickstart post script) or afterwards from HP SIM? Is HP SIM too thick/fat to be an inventory tool? I can't tell if it's meant to be used standalone or alongside other monitoring products. Since the majority of the systems I'm trying to track are those running Gentoo (in order to plan the move to CentOS), is there any way for HP SIM to extract system model information from them ( like dmidecode)? I have systems here where I may have an SSH key established, but not direct user or login access. Is there a way for me to import an SSH private/public key pair into HP SIM to reach out to the servers that can't accept standard credentials? There are a handful of sites where I have inconsistent access or have a double-NAT situation. I may be able to poke a server, but it may not be able to find its way back to the management system. Is there a workaround for this? The certificate configuration for HP SIM seems complicated. What is the preferred setup for trust between systems? I'd also appreciate any notes or recommendations to using this product. Or if there's a better way to do this, I'd like to know.

  Read the article

< Previous Page | 131 132 133 134 135 136 137 138 139 140 141 142  | Next Page >