Search Results

Search found 4396 results on 176 pages for 'low poly'.

Page 135/176 | < Previous Page | 131 132 133 134 135 136 137 138 139 140 141 142  | Next Page >

• Why am I missing 4GB of RAM on Windows Server 2008 R2 64bit?

  - by Nick G

  I noticed today that a server was very low on memory. It physically has 8GB installed and runs Windows 2008 R2 Standard 64bit. It also hosts 2 virtual machines using HyperV. Server is Dell Poweredge R510. However the host OS reports in task manager that it only has 4GB of RAM, despite actually having 8GB and it being a 64bit OS. Computer properties shows Installed memory: 8.00GB (3.99GB usuable). Why would "usable" be half the real RAM installed under a 64bit OS? Additionally nearly all of the 4GB of visible RAM on the host OS is being used by something without anything showing up in task manager (presumably HyperV as it's allocated 3.6GB to the virtual machines its hosting). However that doesn't explain where the other 4GB has gone which Windows can't even see. Where is my missing 4GB of RAM? Update: Dell OpenManage says this: Total Installed Capacity 8192 MB Total Installed Capacity Available to the OS 4096 MB So looks like Nathan's suggestion of memory mirroring might be correct. I'll have to reboot to check this (I think?) Update 2 OK. So I reboot and I get a message saying "the amount of system memory has changed" (despite not having touched the hardware in a year). Once Windows has booted, all 8GB is visible again. Looks like I probably have a hardware RAM issue (I'll perhaps try reseating it whenever I can chuck everyone off the server next). Thanks for your answers and comments. I was hoping it was going to be the mirrored-RAM option but it seems not - that's not even mentioned in the BIOS.

  Read the article

• IP to IP forwarding with iptables [centos]

  - by FunkyChicken

  I have 2 servers. Server 1 with ip 1.1.1.1 and server 2 with ip 2.2.2.2 My domain example.com points to 1.1.1.1 at the moment, but very soon I'm going to switch to ip 2.2.2.2. I have already setup a low TTL for domain example.com, but some people will still hit the old ip a after I change the ip address of the domain. Now both machines run centos 5.8 with iptables and nginx as a webserver. I want to forward all traffic that still hits server 1.1.1.1 to 2.2.2.2 so there won't be any downtime. Now I found this tutorial: http://www.debuntu.org/how-to-redirecting-network-traffic-a-new-ip-using-iptables but I cannot seem to get it working. I have enabled ip forwarding: echo "1" > /proc/sys/net/ipv4/ip_forward After that I ran these 2 commands: /sbin/iptables -t nat -A PREROUTING -s 1.1.1.1 -p tcp --dport 80 -j DNAT --to-destination 2.2.2.2:80 /sbin/iptables -t nat -A POSTROUTING -j MASQUERADE But when I load http://1.1.1.1 in my browser, I still get the pages hosted on 1.1.1.1 and not the content from 2.2.2.2. What am I doing wrong?

  Read the article

• P2V Wouldn't Boot, Rebuilt initrd, Need to Clean Up

  - by Mike Soule

  We have a CentOS 5.4 server (build 2.6.18-164.el5xen). We went to P2V this server so we can have redundancy, the physical only has one PSU. The P2V only completed 99% of the way, we have a VMWare ticket opened, but they marked the ticket as low priority. I was able to boot into a rescue disc of Red Hat 5.4 and rebuild the initrd with the help of this blog post. Now the only issue is the original server had a modified initrd, which was also from a different OS build and made by an outside provider. We do not have a document outlining modifications. My question is, is it at all possible to copy the initrd off of the physical server and replace it on the virtual and some how have the virtual machine boot? Thanks for any input. Edit: I copied the initrd img from the physical and it recreated the original issue. Here is a screen capture of the error. http://i.imgur.com/MqC73.jpg Edit2: echo Scanning logical volumes lvm vgscan --ignorelockingfailure echo Activating logical volumes lvm vgchange -ay --ignorelockingfailure VolGroup00 resume /dev/VolGroup00/LogVol01 echo Creating root device. mkrootdev -t ext3 -o defaults,ro /dev/VolGroup00/LogVol00 echo Mounting root filesystem. mount /sysroot

  Read the article

• Notebook display problem (multiplication)

  - by SubniC

  Hi, I'm having some troubles with the display of a LG E500 notebook. The thing is that without any known reason the display starts to show the screen divided in eigth parts and each part show the display image as if I had a matrix of eigth displays :) I thought it could be some kind of refresh rate problem or driver related, but it is happening at boot-up as well and the BIOS. I got the computer completely unassambled yesterday and I check all the wires and connectors looking for something broken or unconected, but without luck... You can see a picture here of the problem (sorry for the low quality, but I think it illustrate the problem. EDIT 1: I uploaded a new pictrue, here you cans ee the problem better :) There are three horizontal lines that you can see just between the windows. You can see the grey line at the first moment you turn on the computer and the after the duplicated screens show up just like if they where arranged over a grid (over the horizontal lines...) I hope it makes any sense. Do you know what could be happening? or can you tell me what would you do? Thank you very much for your help.

  Read the article

• 150 TB and growing, but how to grow?

  - by seandavi

  My group currently has two largish storage servers, both NAS running debian linux. The first is an all-in-one 24-disk (SATA) server that is several years old. We have two hardware RAIDS set up on it with LVM over those. The second server is 64 disks divided over 4 enclosures, each a hardware RAID 6, connected via external SAS. We use XFS with LVM over that to create 100TB useable storage. All of this works pretty well, but we are outgrowing these systems. Having build two such servers and still growing, we want to build something that allows us more flexibility in terms of future growth, backup options, that behaves better under disk failure (checking the larger filesystem can take a day or more), and can stand up in a heavily concurrent environment (think small computer cluster). We do not have system administration support, so we administer all of this ourselves (we are a genomics lab). So, what we seek is a relatively low-cost, acceptable performance storage solution that will allow future growth and flexible configuration (think ZFS with different pools having different operating characteristics). We are probably outside the realm of a single NAS. We have been thinking about a combination of ZFS (on openindiana, for example) or btrfs per server with glusterfs running on top of that if we do it ourselves. What we are weighing that against is simply biting the bullet and investing in Isilon or 3Par storage solutions. Any suggestions or experiences are appreciated.

  Read the article

• Mysql server high trafic makes websites really slow or unable to load

  - by Holapress

  Lately we have been having a lot of problems with our mysql server, from websites being really slow or even unable to load them at all. The server is a dedicated server that only runs our mysql database. i have been running some test using a profiler (JetProfiler) and tool to stress test (loadUI). If I use loadUI to connect with 50 simultaneous connections to one of our websites that runs a resently big query it will already make the website be unable to load. One of the things that makes me worried is that when I look at Jetprofile it always shows a Treads_connected of 1.00 and it seems that when it hits around 2.00 that I'm unable to connect. The 3 big peaks are when I run a test with loadUI, first one was 15 simultaneous connections wich made it still able for me to load the website but just really slow, the second one was 40 simultaneous connections which already made it impossible to load and the third one was with 100 connection which also didn't make it load anymore. Another thing that worries me is that in JetProfiler it says all the queries that get used are full table scans, could this maybe be the problem? The website I run as a test runs 3 queries, one for a menu that outputs around 1000 rows, one for the adds that has around 560 rows and a big one to get posts that has around 7000 rows (see screenshot bellow) I also have monitored the cpu of the server and there seems to be no problem there, even when I make a lot of connections with loadui the cpu stays low. I can't seem to figure out what is the main cause of the websites being unable to load when there is a high amount of traffic, if anyone has other suggestions for testing or something that might cause the problem please let me know.

  Read the article

• VPS goes slow at more than 20 users online at the same time

  - by hachiari

  I have 512 MB VPS (brustable to 1GB) Somehow, the site goes slow when there are about 10 users, and becomes impossible to load at 20 users online at the same time. I wonder what could be the problem for this. The bandwidth connection of the VPS is 1Gbps. Here is some settings in my VPS: KeepAlive Off <IfModule prefork.c> StartServers 7 MinSpareServers 7 MaxSpareServers 10 ServerLimit 64 MaxClients 64 MaxRequestsPerChild 0 </IfModule> my.cnf settings - calculated Max Memory 300MB Output from UNIXBENCH INDEX VALUES TEST BASELINE RESULT INDEX Dhrystone 2 using register variables 376783.7 13429727.4 356.4 Double-Precision Whetstone 83.1 1137.5 136.9 Execl Throughput 188.3 1637.4 87.0 File Copy 1024 bufsize 2000 maxblocks 2672.0 148868.0 557.1 File Copy 256 bufsize 500 maxblocks 1077.0 79430.0 737.5 File Read 4096 bufsize 8000 maxblocks 15382.0 1410009.0 916.7 Pipe Throughput 111814.6 4419722.0 395.3 Pipe-based Context Switching 15448.6 561505.1 363.5 Process Creation 569.3 10272.7 180.4 Shell Scripts (8 concurrent) 44.8 514.3 114.8 System Call Overhead 114433.5 3537373.8 309.1 ========= FINAL SCORE 295.0 I am afraid that the VPS company limit the number of connection to the VPS... is it possible? The server is in Japan, but the site has global traffic (some of the traffic are from countries with low speed connection). Could this be the problem? This is a serious problem :( my site just cant grow if this keeps on happening... please tell me if you have any idea. Thank You, Bryant

  Read the article

• Troubles Installing Windows 7 via USB. Flat install?

  - by Brian

  Hi friends, I've been struggling with this for a while. Windows 7 64-bit Enterprise edition just will not install on my Shuttle K45 system via a USB key. It hangs out during the install while copying files or while creating the partitions. The system is pretty standard and low-tech: IDE hard drives, no CD, 2G RAM. I am not sure what of the problem. Other than the Shuttle, I have a Apple MacBook Pro. On the MPB, I am running OS X, and Mint Linux and Window XP over Parallels. I have an ISO of Win7 that works (I installed it as a Parallels VM to make sure). I have used UltraISO and MS Windows 7 USB/DVD Download Tool to write it to the 8G USB key. Both seem to copy all the files correctly (with UltraISO, I asked it to verify). It boots via USB and the install looks just fine. Until it hangs, most of the time with a copying error of 0x80070241. So now I am trying to figure out if there are other ways I can install Windows 7 on this Shuttle system that has no CD drive. I've heard about a flat installation, however those all seem to be doing something from within Windows. I do have access to a command prompt from the Windows 7 install. Does anyone know if/how I can prep the Shuttle hard drive with Windows 7 installation and have Windows 7 install from the hard disk. I do not have an external enclosure for the IDE HD and I do not have any other system I can hook up to the hard drives. I do have an external Maxtor OneTouch drive available.

  Read the article

• MS Word TOC that references # pages rather than page number

  - by buttonsrtoys

  We frequently need to write specifications in Word which require a TOC that refers to the total number of pages in a section, rather than the page number. E.g., Section No. Pages 01010 Summary of Work..............5 01025 Prices.......................2 01400 Quality Control..............1 01700 Contract Close Out...........2 A wrinkle is that each section is a separate file. To date, we've been writing or TOC by hand, which has introduced every error imaginable. Is there an MS feature that populates a TOC with page totals? If not, I've done a little VB in Office, so wouldn't be opposed to that route as need be, as long as it was usable by our low tech users. Related question - all the section files are in the same folder. It would be nice if the TOC loaded every file in a folder, rather than having to specify each one. Is this a feature of Word or would this require VB? We tried a master document with links to subdocuments, but since the number of section files ebbs and flows with each project, the approach required too much maintenance for our Wordophobes.

  Read the article

• BackupExec 12 + RALUS - VERY slow backups

  - by LVDave

  We use Backup Exec 12 and the Remote Agent for Linux/Unix Servers (RALUS) to backup a large RHEL5 system. For various reasons we need to do a daily working set job. These working-set jobs run abysmally slow. The link between the target machine and the BE server is gigabit, and any other type of job runs 1-3GB/min. These working-set jobs start out at perhaps 40MB/min and over the course of the backup job slowly drops down so low that the BE job rate display in the "current jobs" goes blank.. Since we usually are only doing changed-files for one day, the job is usually small and finishes overnight and we don't worry abotu the slowness, but we had some issues with the backup server, and missed about 6 days of fairly heavy work on the Linux box, so this working-set job will be a doozy.. We have support with Symantec, and I've pestered them a lot about this, they've had me run RALUS in debug mode, sent them that log and a VXgather from the BE host and they had no fix/workaround.. To give an idea, I have the mentioned working-set job running for the last 3 1/2 hours and it's backed up just under 10MEGAbytes.... I'm posting this here to see if anybody in the "real world" has seen this/and/or has any ideas what might be causing these abysmally slow jobs, since Symantec seems to be clueless...

  Read the article

• PHP unable to allocate memory.

  - by AlReece45

  On my way to the office this morning, every website on our shared VPS started giving the same error (several times, not the typical memory_limit error which is fatal): Warning: Unknown: Unable to allocate memory for pool. in Unknown on line 0 The shared server is a 64-bit OpenVZ container running cPanel. There are only ~6 VPSes on the host-- this is the largest one at only 4GB. The host itself has 24GB RAM. As the below graphs show, the memory usage on the host and VPS are both rather low. CPU Usage/Disk/Host all seem to be normal. RlimitMem was set to 583653034, yet the memory usage is about the same as it usually is. Apache 2.2, PHP 5.2 (mod_php) Restarting Apache has corrected the problem for now. However, I'd like to prevent it from happening again and I'm not sure what was limiting the memory. RlimitMem was set to 583653034, yet the memory usage is about the same as it usually is. There's seems to be plenty of memory: what caused this error? VPS Memory Usage Host Memory Usage APC Information apc.ttl=0 apc.shm_size=0 apc.mmap_file_mask=(blank) 1 Segment(s) with 32.0 MBytes (mmap memory, pthread mutex locking)

  Read the article

• Block SMTP connections from mail domains which don't themselves accept SMTP connection.

  - by bignose

  I'm administrating a mail service for a small business. Their mail host's internet connection is an ADSL service with a permanent IP address. Unfortunately, many misconfigured mail systems will happily deliver to this host, but, when the host attempts to send mail back (e.g. a bounce notice, or a normal response from someone), the original sender refuses to receive connections from this host. That misconfiguration makes their system a one-way mail sender, which is a problem. How can I configure Postfix on this customer's mail host to refuse SMTP sessions that declare a sender domain which itself refuses SMTP from this host? That is, if the SMTP client declares a domain that we can't make SMTP connections back to, then there's not much point accepting the incoming connection in the first place. I'm imagining a late check (after the low-cost checks to winnow most of the rubbish connections) that keeps the client on the other end while it attempts an SMTP client connection back to the declared domain of the sender. If that connection is rejected, the incoming one is also rejected. I'm also open to other suggestions for how this problem might be addressed (short of not using this mail host at all, which isn't an option).

  Read the article

• Recommendation for a simple no-frills Windows PDF printer driver?

  - by Scott Bussinger

  I'm looking for an extremely simple Windows PDF printer driver that I can recommend to clients. Ideally it would have these characteristics: When you print something, it should just create it as a temporary file and then display it in their default PDF viewer with no prompting. If they want to save it, they can save it manually from inside the viewer. This workflow should be with no special post-install configuration. Installation should be very simple. A double click the installation program and click "Finish" sort of thing. No complicated multi-step installation, no asking questions your grandmother wouldn't know the answer to (preferably no questions at all), no extra crap being installed. An option for a completely silent installation would be nice, but not necessary. Ideally it would be free to simplify their installing on a small network, but low cost is an option. I've tried a quite a few but none really fit the bill. Some can achieve the first goal but only after careful configuration, some try to install extra toolbars, some have other installation complexities that would make it hard for extremely novice users to succeed. Any suggestions? Thanks!

  Read the article

• Application that will identify percentage of your system disk bandwidth used on a user-application by user-application basis?

  - by Warren P

  I always (subjectively) feel my computer is far too slow (however fast it is), and so I'm always looking for ways to measure and understand what my computer is actually doing, that is making it seem "slow" to me. It has been my observation that my software-developer workload is most often disk-bound (I am waiting for Disk I/O) more than CPU bound. What has made it worse, is that I am using a corporate PC that has in-memory active-scanning anti-virus software that I do not have control over, and also some IT department mandated services that seem to suck up a lot of available hard-disk bandwidth. The best tool I have seen (in Windows 7) is the Resource Monitor which I usually acess from the button in the task Manager. The disk IO page, however, seems to label Disk Activity at a very low level (for example, showing the Volume Shadow Storage, which is flushing information obviously written by something ELSE other than VSS itself, and then writes to Pagefile.sys, which are obviously due to Virtual Memory faults in some application). What I would like to know is if a utility exists that can add up all direct disk input and output by user-level process, or find the process or service that caused VM or VSS activity. In that way, I hope, you could establish a real idea of how much of your computer's precious disk subsystem bandwidth is attributable to a particular application. here's a scenario: MyApp.exe writes 100k/s and reads 100k/s directly. VSS ends up writing another 100k/s. pagefaults caused inside MyApp.exe cause another 100k/s of writes. So the total "cost" of MyApp.exe running, during a period of time (let's say 1 second) is 400k/s, whereas you can only directly observe half of that, in Resource Monitor. Is there a smarter disk-IO watching piece of software I can use?

  Read the article

• Help configuring Mercury mail or similiar with XAMPP to send e-mail outside of localhost

  - by user291040

  I'm building a PHP/MySQL driven website for my department at work (installed via XAMPP). I need to be able to send mail to outside e-mail addresses (e.g., Yahoo, Hotmail, etc.) using the PHP mail() function. As I see it I have to solutions: Configure the SMTP directive in php.ini to the server running at my work. Configure/run a mail server that can send e-mails outside of localhost (I'm trying Mercury because it comes installed with XAMPP). Here are problems I've come up against: I took a guess at our SMTP server name, and when calling PHP mail(), I get the error SMTP server response: 530 5.7.1 Client was not authenticated I can't be sure, however, the SMTP name is correct (I can't get help from our IT guys because of politics). I have tried to use mercury mail. Mercury seems to be picking up the request, but it doesn't want to forward the e-mail to the outside. I keep getting a Temporary error 240 (temporary MX resolution error). I've searched high and low but still can't find a definitive answer on how to send e-mails outside of localhost. Any help is greatly appreciated.

  Read the article

• Anyone have real world experience with Rackspace Cloud Sites at high scale?

  - by Allara

  I have a pure web service application layer using .NET. I was originally planning to use Amazon EC2, but rolling my own autoscaling procedures is a bit intimidating, and the scaling isn't very granular from a cost perspective. If the app is successful, we could be looking at relatively high scale (millions of requests per month). The app uses Amazon SimpleDB as the database layer. As a test, I have the app running successfully in Rackspace Cloud Sites. Performance seems to be equal to (if not better than) a standard EC2 instance, even with the added latency of the SimpleDB requests travelling to the Rackspace network. However, testing at this stage is at a very low scale. My question is this: has anyone had real-world experience running a high scale application on Rackspace Cloud Sites? Moreover, once you pass the "included" 10,000 compute cycles per month, does the overall cost seem to be lower than rolling lots of EC2 instances? My assumption would be that with completely smooth scaling (i.e. only adding compute resources as needed), the cost could be lower on average. However, their stated goal of calibrating 10,000 CCs as a single 1.2 Ghz CPU seems on average to be much more expensive than EC2. I like the idea of no-touch scaling, but is it too good to be true?

  Read the article

• Extend Linux Desktop to another X Windows Display

  - by unknown (google)

  Hello, I am a long time Linux user of the Xinerama and other technologies for extending a desktop to multiple monitors. However when I travel with my laptop I miss the multi-monitor support I enjoy at home. Recently I acquired a second laptop for a low price. Both laptops are running Fedora (versions 10 and 11 respectively). I use Gnome as my primary desktop environment. I know about synergy. I use synergy all the time to control the screen of other Windows / Linux systems I use. I would like to know, can I sit both my primary and secondary laptops together and achieve a Xinerama-like extended desktop environment? Ideally I would like to start a GNOME session on my primary laptop. And then start a X-Windows Desktop on my secondary laptop and extend my primary laptop's desktop onto it. I would like to be able to move Windows from the primary desktop to the secondary laptop desktop. Would I need to use synergy to do this with some other bit of X-Windows technology? Or is there X-Windows technology that will do all this for me? I am familiar with X Windows ability to display applications remotely. I am also familiar with Nomachine's NoX.

  Read the article

• quad sli with gtx 690 not working

  - by Moaadh

  I have two cards GTX 690 (dual core). I did the Sli successfully. Nvidia control panel acknowledges the two cards as quad Sli. However, the problem is that Windows 7 64-bit Ultimate is showing me the graph memory size as 4 GB while it is supposed to be 8 GB because of the Sli. Also the benchmark from all software is giving me a very low score compared to some other guy's benchmark on YouTube. It gives me a big headache. Does anyone know why this is happening? If so, how can I get Windows 7 to recognize all 8 GB of memory? Thanks for your help in advance. My computer specifications: (Processor: Intel Core i7-3930k @3.2GHz(12CPUs))--- (Memory: 65536 MB Ram 1866 MHz)-- (OS: Windows 7 Ultimate 64-bit)-- (OCZ 240GB as SSD PCIe drive for booting and storage disk)-- (DirextX version: DirectX 11)-- (VGA Card: 2 X EVGA GTX 690 Dual GPU. Each GPU is 2 GB, so total memory should be 8 GB.)-- (MotherBoard: ASUS Rampage IV Extreme)-- Others with lesser specifications get a 2500 score in heaven benchmark while I get 1501 as if it is one card.

  Read the article

• Gigabit network limited to 25MB/s by CPU. How to make it faster?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? The other computers in the network can usually transfer at 50+MB/s without problems. And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• NFS on top of GFS2 - does it work?

  - by Matthew

  We're currently using a NoSQL derivative called Splunk to receive our data. The software supports something called "search head pooling" in which the job-dispatching engine is housed on several servers which share a common storage point. Originally our intention was to use a clustered filesystem like GFS2 because of low latency, stability, and ease of setup. We set up GFS2, and it's working with no issues. However when trying to run the software, it's trying to create lock files, and a bunch of other things that their support team can't quite explain. Ultimate feedback from them was that they only support NFS. Our network administration team heavily frowns on NFS (lack of stability, file lock issues, etc). So, I was thinking about the possibility of setting up NFS on each server in the cluster to act as a wedge layer between the GFS2 filesystem and the software. Basically configure each server to export the GFS2 filesystem's mountpoint via NFS, and then tell each server to connect to that NFS share. That way we aren't introducing any single-points-of-failure should a dedicated NFS server go down, but the vendor gets their "required" NFS share. I'm just brainstorming ways around, so please tear this apart :)

  Read the article

• credit or minclass does not work well with pam_cracklib.so in common-password (opeSuSe 11.3)

  - by Mario

  I'm trying to implement password complexities on my pdc. It's a samba PDC with openLDAP backend. I tried cracklib-check but it looks like that I should have a decent and localize version of password library since the library out there usually comes in english. I also have another consideration that we will allow users to use any kind of password - even though it's dictionary based - as long as their passwords integrated with low/upper alphabet, digits, and other characters such as '$' or '_' (pam_cracklib.so calls them as classes). So here is my /etc/pam.d/common-password: #password requisite pam_pwcheck.so nullok cracklib password requisite pam_cracklib.so minclass=4 reject_username ##password requisite pam_cracklib.so \ ## dcredit=-1 ucredit=-1 lcredit=-1 ocredit=-1 reject_username password optional pam_gnome_keyring.so use_autht_ok password required pam_unix2.so use_authtok nullok The first commented line (with #) was the default configuration of openSuse 11.3. The 2nd/3rd (with leading ##) is another configuration I use when minclass=4 line is commented out. By the way, I have 'check password script' = /usr/local/sbin/crackcheck -d /usr/share/cracklib/pw_dict and passdb backend = ldapsam:ldap://127.0.0.1 parameters in smb.conf and cracklib-check works fine too. So here is the test I conduct. I logon to windows and then change my password. Sometimes it works fine that it trows error message - which what I wanted, but simple password with only lower alphabets can pass windows change password. Maybe I should make a new library which incorporates local vocabularies, but a guy out there (raise your hand please if you read this :) ) also experienced the same trouble with english word. Besides, what we really want is to let user to choose 2 or 3 format password out of 4 classes. Is there a bug or something with pam module in openSuse 11.3? Thank you in advance. Regards, Mario

  Read the article

• 3dmark score abnormal

  - by Sean

  I just bought a new laptop. It is core i7 3610QM.(Ivy bridge, 4 core plus hyperthreading), 8G ram, nvidia GT 610M 2GB. The OS is Win7 64bit. I ran 3dmark 11, but the score is frustrating. For 1280*720, the score is P730. It is too low right? I searched online, the score should at least above 1000. Am I right? I never use this software before. I know nvidia has optimus, so I made the laptop in high performance state and white-listed the 3dmark program. But there is no help. I am guessing 3dmark is using i7's graphic module. It cannot transform to nvidia. In the running detail of 3dmark, the graphic card cannot be identified(The row remain blank). Can anybody tell me is this the normal case? If not, can I use some other software to test if my nvidia card is working fine? If this nvidia card cannot work, I will return the new laptop asap. Thanks.

  Read the article

• HP/IBM alternative to Buffalo iSCSI TerraStation?

  - by Robin Day

  I'm looking at virtualising some of our infrastructure in order to allow for more resiliance and future expandability. We have successfully virtualised on single servers with Direct Attached Storage and are now looking for a more future proof solution using a high powered host (or two) and a SAN (or two). I'm thinking that the host machine will probably be an HP ProLiant DL360 G7 (all of our exisiting infrastructure is HP). Unfortunately, I am new to the world of SANs. From what I can see, the Buffalo Terrastation III is all I would need in order to setup an iSCSI SAN for VMWare to use. However, I'm a little reticent to go that way as it's a bit too "entry level" for my liking. In particular I would be very keen for more redundancy, power, networking, etc. I'm also very aware that you "get what you pay for". Therefore, can anyone reccommend equivalents from the big boys? HP/IBM? I have searched high and low on the HP site and seen many options but am struggling to work out if it is all the hardware I will need. Some options appear to need separate controllers from disk enclosures, etc.

  Read the article

• Reset sound volume in Windows 8

  - by Svish

  There seems to be a bug in Windows 8 causing the maximum volume to become lower than it really should be. I'm now at a stage where I put the volume up to max and the sound is still very low. I have a couple of Logitech Z-10 speakers with a display on them and when I touch the increase volume button on that it shows me the volume (but not able to increase it) is actually below middle even though Windows claims it to be maxed out. Is there any way I can reset the volume in Windows 8 so that I can get it up fully max again? A registry setting or something? Really don't want to have to reinstall windows or drivers or anything like that cause if it is a bug it'll probably happen again and I really don't want to have to do that every time this happens :p Any ideas? Manged to fix it by unplugging the usb connection to my speakers, turning the volume down on my computer and up on the speakers, and finally reconnecting the usb connection. Seems to have been an issue with the speakers and not Windows this time. BUT, I'm still curious how you can adjust/reset the Windows 8 sound volume without using the volume controls. Like, where is the value of the current volume setting(s) really stored? And can you manually adjust them?

  Read the article

• What does SQL Server's BACKUPIO wait type mean?

  - by solublefish

  I'm using Sql Server 2008 ("R1"), with some maintenance plans that back up my databases to a network share. Some of my backup jobs show long waits of type "BACKUPIO". Of course it seems like this is an I/O subsystem limitation, but I'm skeptical. Perfmon stats for I/O on the production (source) server are well within normal trends for that server. The destination server shows a sustained 7MB/s write rate, which seems incredibly low, even for a slow disk. The network link is gigabit ethernet and nowhere near saturated. The few docs I've turned up about BACKUPIO indicate that it's not specifically a wait on I/O, surprisingly enough. This MSFT doc says it's abnormal unless you're using a tape drive, which I'm not. But it doesn't say (or I don't understand) exactly what resource is missing. http://www.docstoc.com/docs/24580659/Performance-Tuning-in-SQL-Server-2005 And this piece says it's not related to I/O performance at all. http://www.informit.com/articles/article.aspx?p=686168&seqNum=5 "Note that BACKUPIO and IO_AUDIT_MUTEX are not related to IO performance." Anyway, does anyone know what BACKUPIO actually means and/or what I can do to diagnose or eliminate it?

  Read the article

< Previous Page | 131 132 133 134 135 136 137 138 139 140 141 142  | Next Page >