Search Results

Search found 5906 results on 237 pages for 'opn specialization guide'.

Page 136/237 | < Previous Page | 132 133 134 135 136 137 138 139 140 141 142 143  | Next Page >

• Exchange 2003 and Outlook rule: Send auto reply message not working

  - by Mestika

  Hi, I have created a distributed group which have to send a auto reply when receiving a mail. I know that it is impossible to send a auto reply within a distributed group, but following a guide I have created a mail account called “noreply”. In outlook I have created a rule in the “noreply” account where I chose following conditions: Send to a person or distributed list (where I selected my distributed group) Then to specify what to do with that message I selected Have server reply using a specific message I’ve created my message and saved it. But when I try to write an e-mail to the distributed group it doesn’t send back the reply message. Does anyone knows what I’m doing wrong? Sincerely Mestika

  Read the article

• How to rebuild a Li Ion laptop battery?

  - by spoulson

  I have an aging Gateway NX560XL laptop. The battery is toast and a new one, even aftermarket, starts at $130. So, to experiment, I began tearing apart the old battery to see what can be done. I found it used 8 standard size 18650 Li Ion cells arranged two cells parallel then in series (like: ====). Some online shopping revealed ~$7-13/ea replacements depending on mAh output. My plan is to load test to determine the bad cells and replace only those, as I read that typically only 1 or 2 may be bad. I'm proficient with soldering, however these cells are attached with welded tabs. Some of them broke during disassembly and I'm not sure how to reattach them. What I found online are cells like these that have solder tabs pre-welded to the ends so I can solder wires onto. Is there any guide available that provides the instructions and parts to do this kind of rebuild?

  Read the article

• What's the best way to clean up after a fork bomb?

  - by raldi

  $ ls bash: no more processes Uh oh. Looks like someone made a fork bomb. Where I used to work, this pretty much meant that the shared server would need to be power-cycled, since even the sysadmins with root often couldn't get the problem cleaned up. Often, they couldn't even get a prompt. I've heard a few tricks (notably, to send STOP signals rather than KILL signals, since the latter would allow the remaining threads to immediately replace the killed ones), but I've never seen a comprehensive guide entitled So, You Have Yourself a Fork Bomb? Let's make one.

  Read the article

• LDAP Bind request failing

  - by Madhur Ahuja

  I have a Windows Server 2008 R2 Active Directory domain controller with domain madhurmoss.com I have a Linux box which is trying to connect to LDAP (389) on above box, which is failing. Upon inspection in Wireshark, I see a bind request with following query sAMAccountName=Administrator,DC=madhurmoss,DC=com and result with invalid Credentials 80090308: LdapErr: DSID-0C0903A9, comment: AcceptSecurityContext error, data 52e, v1db0 I want it to connect it through Administrator which lies in CN=Administrator,CN=Users,DC=madhurmoss,DC=com The supplied credentials are correct. I believe the query sAMAccountName=Administrator,DC=madhurmoss,DC=com is wrong. Can anyone guide me what could be wrong ?

  Read the article

• How do I recover from a grub renaming issue?

  - by Justin Ardini

  I am currently dual-booting Ubuntu 10.04 and Windows 7 with grub 1.98 as the bootloader. I recently decided to edit the grub menu to remove the old Ubuntu kernels, so I followed the instructions of this guide and added the line list='version_find_latest $list' to the 10_linux file, then ran sudo update-grub. Apparently I made a mistake, because upon restart I had these bootloader entries: Ubuntu, with Linux $list Ubuntu, with Linux $list (recovery mode) Ubuntu, with Linux version_find_latest Ubuntu, with Linux version_find_latest (recovery mode) When I try to load any of these, I get a grub error along the lines of, Error: not a normal file Now I can't start any version of Ubuntu to remove the line I added. What's the best course of action to be able to use Ubuntu again? Thanks.

  Read the article

• Installing Gitolite on NAS - FATAL: have errors but logging failed

  - by Jay

  I'm trying to install Gitolite on my Synology DiskStation, following these instructions: http://www.bluevariant.com/2012/05/comprehensive-guide-git-gitolite-synology-diskstation/ Under "Install Gitolite on the DiskStation and Run Setup" When I run the gitolite install command: DiskStation> /volume1/homes/git/gitolite/install -ln /bin I get the following error: FATAL: have errors but logging failed! 2012-05-31.00:10:22 no GL_LOGFILE env var 2012-05-31.00:10:22 die could not symlink /volume1/home/git/gitolite/src/gitolite to /bin<<newline>> at /volume1/home/git/gitolite/install line 71<<newline>> I am very new to all of this. Does anyone know what this means, and how I can fix this error? Thank you very much.

  Read the article

• How do I get Bugzilla to authenticate with Active Directory LDAP?

  - by user65712

  After reading this guide and trying a ton of permutations based on that, is there an easy way to get Bugzilla working with an AD server? I keep getting the error: 80090308: LdapErr: DSID-0C0903A9, comment: AcceptSecurityContext error, data 52e, v1db0 I created an AD "bugzilla" user account with "Account Operators" permission as directed. I'm not sure if the error is saying that my login is incorrect or the system login to access LDAP is incorrect. Maybe I just missed an arcane option somewhere in the settings. You'd think all I'd need to do is specify the server name. As you might have been able to tell, I don't have a lot of LDAP experience. Also, will the Sysinternals LDAP tool help here?

  Read the article

• Create 301 Redirection in Amazon Route 53 for Wildcard Subdomains

  - by Eric Yin

  My domain name hosted on Route 53 DNS. Amazon has a guide to do 301 redirection for www. To naked domain by point www. version to a S3 static website with 301 setted up. My question is, how can I have *.domain.com all have 301 redirec to naked domain name. I guess either: Some way to get all wildcard subdomains end up into one S3 bucket, how? Or: Use CloudFront on the www. version S3 site and put wildcard subdomains on the CloudFront, but how? Or: There's some hidden settings just lies on Router 53, then where? Or: use EC2, better not suggest me this, too costing for this task. Please advice.

  Read the article

• How do I give MacPorts privileges?

  - by cojadate

  I tried to install PostgreSQL server development libraries using MacPorts and got the following: Warning: MacPorts running without privileges. You may be unable to complete certain actions (e.g. install). ---> Computing dependencies for postgresql-server-devel ---> Dependencies to be installed: postgresql-devel ---> Building postgresql-devel Error: Target org.macports.build returned: shell command failed Error: The following dependencies failed to build: postgresql-devel Error: Status 1 encountered during processing. To report a bug, see <http://guide.macports.org/#project.tickets> So I guess that means I need to running MacPorts with privileges and try again. Unfortunately I've no idea how to give MacPorts privileges. I'm running OS X 10.6.3

  Read the article

• How to set up an exim backup mail server

  - by luciano rinetti

  i am using Exim for some years (now i have v4.74 on Ubuntu Server 11.04) with good results, with ClamAV and SpamAssassin. Now i'd like to set up a backup server to improve the continuity of service. Reading the official Exim doc. (specifications and the Philip Hazel book on Exim4 2nd Edition) i don't found a complete guide to implement a synchronized structure (primary + backup). Please could you show me a document/s or URL that let me set it up and offer a better service ? Best Regards luciano

  Read the article

• Can I connect Creative SBS A520 5.1 speakers to my Dell XPS L502X?

  - by vr3690

  I am planning on buying a new set of speakers and was looking at the Creative SBS A520 5.1 Speakers as an option to connect to my Dell XPS 502X. From what I have seen online and on the quick start guide for the speakers, I need to have 3 line out ports on my laptop to use the 5.1 speakers properly. Right now, I have port for 3.5mm jack, one S/P Diff and another for the mic. Can I connect these speakers directly to my laptop without using any other hardware? If I do need some other hardware, what do I need to get?

  Read the article

• Oracle Unicode problem when using NLS_CHARACTERSET is WE8ISO8859P1 and NLS_NCHAR_CHARACTERSET is AL16UTF16, and ColdFusion as programming language

  - by tsurahman

  I have 2 Oracle 10g database, XE and Enterprise XE Enterprise and this are the data type I've use in the test table and then I tried to test to insert some Unicode char from http://www.sustainablegis.com/unicode/ and the results are XE Enterprise for this test, I use ColdFusion 9 developer edition <cfprocessingDirective pageencoding="utf-8"> <cfset setEncoding("form","utf-8")> <form action="" method="post"> Unicode : <br> <textarea name="txaUnicode" id="txaUnicode" cols="50" rows="10"></textarea> <br><br> Language : <br> <input type="Text" name="txtLanguage" id="txtLanguage"> <br><br> <input type="Submit"> </form> <cfset dsn = "theDSN"> <cfif StructKeyExists(FORM, "FIELDNAMES")> <cfquery name="qryInsert" datasource="#dsn#"> INSERT INTO UNICODE ( C_VARCHAR2, C_CHAR, C_CLOB, C_NVARCHAR2, LANGUAGE ) VALUES ( <cfqueryparam cfsqltype="CF_SQL_VARCHAR" value="#FORM.TXAUNICODE#">, <cfqueryparam cfsqltype="CF_SQL_CHAR" value="#FORM.TXAUNICODE#">, <cfqueryparam cfsqltype="CF_SQL_LONGVARCHAR" value="#FORM.TXAUNICODE#">, <cfqueryparam cfsqltype="CF_SQL_VARCHAR" value="#FORM.TXAUNICODE#">, <cfqueryparam cfsqltype="CF_SQL_VARCHAR" value="#FORM.TXTLANGUAGE#"> ) </cfquery> </cfif> <cfquery name="qryUnicode" datasource="#dsn#"> SELECT * FROM UNICODE ORDER BY LANGUAGE </cfquery> <table border="1"> <thead> <tr> <th>LANGUAGE</th> <th>C_VARCHAR2</th> <th>C_CHAR</th> <th>C_CLOB</th> <th>C_NVARCHAR2</th> </tr> </thead> <tbody> <cfoutput query="qryUnicode"> <tr> <td>#qryUnicode.LANGUAGE#</td> <td>#qryUnicode.C_VARCHAR2#</td> <td>#qryUnicode.C_CHAR#</td> <td>#qryUnicode.C_CLOB#</td> <td>#qryUnicode.C_NVARCHAR2#</td> </tr> </cfoutput> </tbody> </table> from this guide http://www.stanford.edu/dept/itss/docs/oracle/10g/server.101/b10749/ch6unicode.htm#i1007297 I think for my Enterprise database it should produce same thing as XE (at least for NVARCHAR2 column) since the typical solution from that guide said: Use NCHAR and NVARCHAR2 datatypes to store Unicode characters Keep WE8ISO8859P1 as the database character set Use AL16UTF16 as the national character set So, how to make it works too in my Enterprise database? Thank you :)

  Read the article

• How to integrate Windows Server 2008 R2's NPS with Cisco switches?

  - by Massimo

  I need to evaluate in a lab environment the use of Windows Server 2008 R2's NPS for 802.1x authentication with Cisco Catalyst 3750 switches; the general idea is to only let clients connect to the company network if they can provide valid domain logon credentials, placing them in a restricted VLAN instead if they can't. NAP would also be a bonus, but it can be evaluated later; the main point now is only 802.1x authentication. Although I have very good knowledge of Windows and Active Directory (on the Microsoft side) and quite good knowledge of Catalyst switches (on the Cisco side), I'm totally new to 802.1x; I'd really like some general guidelines and help here, and some sort of implementation guide would also be very useful.

  Read the article

• Vlan and Switch setting - dummy

  - by Andras Sebestyen

  I need to speak tomorrow the network engineer and I would like to understand his so apologise for the Dummy question: In the school we have a cab with a 24 port Netgear manageable switch with an admin and curriculum VLAN settings. Usually, as I over heard, in the morning and around 4.30pm there are a slowdown period on the computers which connect to this switch. No one could track this back yet. Questions: What is the best way to track back this slowdown Would it be a temporary solution to physical separate the two network with 2 switches If that would work how can I link them together to be able to see the curriculum from the admin side. Do I need an extra router then? Too many questions but I have no clue where to start and the gentleman will be paid by hours... can you see where I am coming from?:) Could you guide me in the right direction please? Any comment would be appreciated and please send links if you down vote the question:)

  Read the article

• Receive emails on Amazon EC2 Server

  - by Kartik

  I just got started with an EC2 instance and got my mail sending limit removed, allowing me to send emails from my instance. But due to lack of experience, I have no clue on how to enable receiving emails send to me on that server. The instance has an elastic IP and I have a domain name with an A record pointing to that IP. I cant seem to find better documentation on what steps need to be taken so if someone sends an email to [email protected] it either actually receives it or simply forwards it to my personal email. I know that it involves using postfix but cant find a guide to properly configure it after the installation. Thanks

  Read the article

• Ubuntu, control the init startup

  - by Xolve

  Ubuntu uses upstart instead of sysvinit. However there are still runlevels and the links in them. I have installed tor and it has added itself to the startup of the OS. Now I want to remove it and the popular options are to remove the links of starting and stopping the service from runlevels or make the /etc/init.d/ script non-executable. This is fine but this will be problematic in case I want to put tor again on the startup list. How would I know to put the proper sequences in the proper runlevel directories. Is there any complete guide given? What are the rules for this? Any tools to manage the init? Please tell

  Read the article

• Improving server security [closed]

  - by Vicenç Gascó

  I've been developing webapps for a while ... and I always had a sysadmin which made the environment perfect to run my apps with no worries. But now I am starting a project on myself, and I need to set up a server, knowing near to nothing about it. All I need to do is just have a Linux, with a webserver (I usually used Apache), PHP and MySQL. I'll also need SSH, SSL to run https:// and FTP to transfer files. I know how to install almost everything (need advice about SSL) with Ubuntu Server, but I am concerned about the security topic ... say: firewall, open/closed ports, php security, etc ... Where can I found a good guide covering this topics? Everything else in the server... I don't need it, and I wanna know how to remove it, to avoid resources consumption. Final note: I'll be running the webapp at amazon-ec2 or rackspace cloud servers. Thanks in advance!!

  Read the article

• How do I compile mercurial 1.5.2 on debian?

  - by Aaron Digulla

  I downloaded the files for Mercurial 1.5.2 from http://packages.debian.org/sid/mercurial (mercurial_1.5.2-1.debian.tar.gz, mercurial_1.5.2-1.dsc and mercurial_1.5.2.orig.tar.gz). How do I get a .deb package out of these? I tried to follow the instructions at http://www.debian.org/doc/maint-guide/ch-build.en.html but they don't work. I tried to unpack the two archives and run dpkg-buildpackage or debian/rules build but that fails with: dh --with quilt clean dh_testdir debian/rules override_dh_auto_clean make[1]: Entering directory `/home/user/packages/mercurial-deb' cp -a mercurial/__version__.py mercurial/__version__.py.save cp: cannot stat `mercurial/__version__.py': No such file or directory make[1]: *** [override_dh_auto_clean] Error 1 make[1]: Leaving directory `/home/user/packages/mercurial-deb' make: *** [clean] Error 2 That's because the directory mercurial is inside mercurial_1.5.2/. Why doesn't the build script cd into the right place? If I try ../debian/rules build, I get dh --with quilt build dh: cannot read debian/control: No such file or directory sigh How do I compile a package for debian???

  Read the article

• Can't find netbooted for Kerrighed pxe boot with Ubuntu Lucid Server

  - by Pengin

  I'm following installation guides for pxe booting and kerrighed. I can't find the package nfsbooted for Ubuntu 10.04. Where did it go? Context: At work I have access to 8 mini-ITX PCs and am trying to build a cluster. My plans include trying Condor, GridGain, Hadoop, and recently Kerrighed has caught my eye. (I reaslise these are all for different kinds of things, I'm just evaluating). Ideally, I'd like to have all the nodes network boot from a single server, since that seems so much easier to manage, plus I can 'borrow' additional PCs for a while without touching their HD. I've been getting on great with Ubuntu Lucid Server (10.04), trying to follow the only guides I can find to get pxe booting (and ultimately kerrighed) to work. This guide is for Ubuntu 8.04 and this one is for Debian. They both refer to a package I can't seem to find, nfsbooted. Has this package been replaced? Am I doing something daft?

  Read the article

• setting up/installing/configuring nginx LEMP stack on fresh VPS server

  - by Grant Tailor

  I need some help in settingup/installing and configuring nginx LEMP stack on a fresh new VPS I have. The specs of the CentOS 5.7 VPS are 2GB DDR3 ECC RAM(4GB burst), 1 core 1.5Ghz(3Ghz burst) and 100GB RAID 10 storage, unmetered bandwidth @ 100Mpbs all for a whopping $25/month(unbeatable, yeah I know :) Anyways I have followed this LEMP (will also need MySQL and PHP) stack guide on linode http://library.linode.com/lemp-guides/centos-5 but basically what I want is to be able to host multiple website on this webserver after everything is setup. I am used to using DirectAdmin control panel on other server and want to have things setup so I can host multiple websites - mostly wordpress and drupal themes. Lets say 10 websites on this nginx web server. So can someone please help me on what I need to do to take "full" advantage of nginx power and performance, while been able to easily manage these multiple websites (wordpress and drupal themes)?

  Read the article

• How can I fix puppet refusing to start and asking for "master.pp"?

  - by cwd

  I'm using the very latest version of puppet and have been following the Apress "Pro Puppet" guide step by step. I have installed puppet sudo aptitude install ruby libshadow-ruby1.8 sudo aptitude install puppet puppetmaster facter I have edited /etc/puppet/puppet.conf to include certname [master] certname=puppet.mydomain.com I have edited /etc/hosts and added the following line 127.0.0.1 puppet.mydomain.com puppet I have set the hostname of the server echo "puppet.mydomain.com" > /etc/hostname hostname -F /etc/hostname And then I try and run puppet from the command line. puppet master --verbose --no-daemonize And puppet gives me this error: Could not parse for environment production: Could not find file /master.pp I'm running all commands with sudo and the last line of the error message always says that it can't find master.pp and the path before it is to my current working directory. What am I doing wrong? I should also mention that I don't have a DNS record set up for puppet.mydomain.com - I saw some online documentation mentioning this might be a problem - however I was fairly sure that the hosts file would let me get around that.

  Read the article

• Automatic Site Creation

  - by Eddy Freeman

  I have created a platform that i want users to sign up and a new site is created for them instantly. Users will register and afterwards they will receive a username and password for their personal site. The system will work like ecommerce platforms such as www.shopify.com, www.bigcommerce.com, etc.. where users sign up and a new web-shop is created for them instantly. I have been searching for a while how i can create a script to automate this task but couldn't find any tutorials. Am using LAMP (Linux, Apache, MySql and PHP). Am asking if someone can guide me how to write such script or maybe point me to a tutorial or a book or probably similar scripts to automate this task. Sorry if this place is wrong for this question. thanks for your help.

  Read the article

• How to force-restart a PC with vPro technology?

  - by Dan Nissenbaum

  I would like to know how to force-restart a PC that has crashed/hung and become completely non-responsive, using 2nd-generation vPro technology. Assume there is a second, fully responsive PC on the same LAN that can be accessed remotely to assist. Specifically, I am considering purchasing a PC with an i7-2860QM CPU, which is vPro-enabled (according to Intel). Here are two links that indicate it should be possible to force-restart a hung system with a 2nd-generation vPro-enabled CPU: Seconds 24-39 of What Is Intel vPro™ Technology? Page 17 (21 of the PDF) of Intel® vPro™ Technology: Reference Guide However, after extensive research, I cannot find a straightforward and trustworthy source of confirmation that this will actually work as I describe, or any documentation about how to set it up. I would appreciate both a reliable confirmation, and a source of documentation. This question is a follow-up to: Wake-on-LAN (WOL) fails after computer crashes (Windows 7 64-bit).

  Read the article

• Installing Bugzilla on Ubuntu 9.04 and Plesk

  - by makeflo

  Hey guys. I'm trying to install the latest Bugzilla version on my ubuntu server. (Want to use a subdomain like bugs.domain.com) I already installed all necessary perl modules and check_modules.pl doesn't show any errors. But when I'm running the testserver.pl script I get the following: TEST-OK Webserver is running under group id in $webservergroup TEST-FAILED Fetch of images/padlock.png failed I'm also not able to visit ANY file within the bugzilla folder from the browser. I'm always getting a 404 error. The bugzilla folder and all containing files are set to apache as the owner. I tried to enter the apache configuration form the installation guide in the http.include file of the domain and in the vhosts.conf file of the subdomain as well. I don't know what to do... Playing with plesks' suexecgroup doesn't bring any solution... I hope you can help me! Thanks in advance!

  Read the article

• Apache SSL losing session over load balancer

  - by SaltyNuts

  I have two physical Apache servers behind a load balancer. The load balancer was supposed to be set up so that a user would always be sent to the same physical server after the first request, to preserve sessions. This worked fine for our web apps until we added SSL to the setup. Now the user can successfully login, see the home page, but clicking on any other internal links logs the user right out. I traced the issue to the fact that while initial authentication is performed by server 1, clicking on internal links leads to having the request sent to server 2. Server 2 does not share sessions with server 1, and the user is kicked out. How can I fix it? Do I need to share sessions between the two servers? If so, could you point me to a good guide for doing this? Thanks.

  Read the article

< Previous Page | 132 133 134 135 136 137 138 139 140 141 142 143  | Next Page >