Search Results

Search found 39224 results on 1569 pages for 'content delivery network'.

Page 137/1569 | < Previous Page | 133 134 135 136 137 138 139 140 141 142 143 144  | Next Page >

• Remote network traffic not passing through VPN

  - by John Virgolino

  We have the following topology: LAN A LAN B LAN C 10.14.0.0/16 <-VPN-> 10.18.0.0/16 --- SONICWALL <-VPN-> M0N0WALL --- 10.32.0.0/16 Traffic between LAN A and LAN B works perfectly. Traffic between LAN C and LAN B works perfectly. Traffic between LAN A and LAN C, not so much. LAN A's gateway has a route to LAN C that points to the Sonicwall. The Sonicwall has a route to LAN A pointing to the VPN gateway connecting LAN B to LAN A. Tracing packets on the Sonicwall shows the LAN C destined traffic to arrive on the Sonicwall, but it does not forward the traffic, it dies there. Traffic from LAN B gets forwarded. Tracing packets on the Sonicwall while sending traffic from LAN C destined for LAN A shows nothing. This tells me that the M0N0WALL is not forwarding traffic for the 10.14.0.0 network and the Sonicwall is not forwarding from 10.14.0.0. The SA on the Sonicwall terminates on the WAN ZONE and is defined to use an address group that incorporates both the 10.14.0.0 and 10.18.0.0 networks. The M0N0WALL is configured for the 10.18.0.0 network and I have tried with both a static route to 10.14.0.0 and without on the M0N0WALL. I tried manually adding the 10.14.0.0 network to the SA on the M0N0WALL, but that really aggravated it and the SA never came up, so I reverted. I have checked all the firewall rules to make sure nothing is blocked. All of the Sonicwall auto-added rules look right. Specs: Sonicwall TZ200, Enhanced OS M0N0WALL v1.32 I'm at a loss at this point. Any help would be appreciated.

  Read the article

• Linux will not activate wireless after device has been re-enabled

  - by XHR

  Using a Eee 900A netbook by Asus. By pressing Fn + F2, I can disable or enable the wireless chip on the netbook, a blue LED indicates the status. I've been able to connect to wireless networks just fine with this netbook. However, if the wireless chip ever becomes disabled, I have to reboot to get my network connection back. This generally happens when suspending. For some reason the LED will be off and I have to hit Fn + F2 for it to light up again. However, after doing so, Linux will not reconnect to the network. It simply changes the wireless status from "wireless is disabled" to "device not ready". Even worse, I've recently had issues with the chip being enabled at boot, thus making it nearly impossible to get connected. I've searched around on-line but haven't found much of anything useful on this. This happens on all kinds of different distros including Ubuntu 9.10 Netbook, EeeBuntu 4 beta, Jolicloud and Ubuntu 10.04 Netbook. Edit I noticed this question is getting a lot of views. To give a quick update, I never did resolve this issue with the given distro's. However, I'm currently running Ubuntu 10.10 netbook edition and this issue has gone away.

  Read the article

• PHP application failed to connect after a network plugged back in

  - by tntu

  My data-center appears to have had some issues with their network and thus my server has suffered from on an off network connectivity for about an hour. After the connection has been completely re-established my code still kept reporting the same issue over and over until I have restarted the service. The code is a simple PHP code that loops forever checking the Apple feed-back server and then sleeps for a few minutes and then it begins all over again. Now I understand the error being generated if the network is down but once it got back up why did it continue until I have restarted the code? Does PHP have something that needs to be re-initialized or something?? Messges log: Dec 20 08:57:22 server kernel: r8169: eth0: link down Dec 20 08:57:28 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:29 server kernel: r8169: eth0: link down Dec 20 08:57:33 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:33 server kernel: r8169: eth0: link down Dec 20 08:57:37 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:38 server kernel: r8169: eth0: link down Dec 20 08:57:44 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:44 server kernel: r8169: eth0: link down Dec 20 08:57:52 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:52 server kernel: r8169: eth0: link down Dec 20 09:10:58 server kernel: r8169 0000:06:00.0: eth0: link up PHP Error: PHP Warning: stream_socket_client(): php_network_getaddresses: getaddrinfo failed: Name or service not known in /home/push/feedback.php on line 36 Code Line 36: $apns = stream_socket_client('ssl://feedback.sandbox.push.apple.com:2196', $errcode, $errstr, 60, STREAM_CLIENT_CONNECT, $stream_context);

  Read the article

• PHP Page Stopped outputting content After Running "yum install php-devel" Command

  - by stwhite

  This error is bizarre but after running the "yum install php-devel" command (after a long day of trying to install Facedetect and OpenCV for face detection) my site stopped functioning. The site uses mysql and php. When you hit the url, the page executes the mysql and the php, but it appears to randomly stop outputting the content of the page. None of the code was changed and the site was working flawlessly prior to running the mentioned ssh command. I do use output buffering in the site, but after removing the calls "ob_flush", "ob_end_flush" and "ob_start" it didn't appear to help—still having issues with the site. Any ideas what this could be? Here is output from terminal: [myserver ~]# cd Facedetect-4b1dfe1 [myserver Facedetect-4b1dfe1]# phpize Configuring for: PHP Api Version: 20090626 Zend Module Api No: 20090626 Zend Extension Api No: 220090626 [myserver Facedetect-4b1dfe1]# configure bash: configure: command not found [myserver Facedetect-4b1dfe1]# phpize && configure && make && make install Configuring for: PHP Api Version: 20090626 Zend Module Api No: 20090626 Zend Extension Api No: 220090626 bash: configure: command not found bash: Read: command not found [myserver Facedetect-4b1dfe1]# make make: *** No targets specified and no makefile found. Stop. [myserver Facedetect-4b1dfe1]# yum install php5-devel

  Read the article

• Serving static content with Apache web server and Tomcat

  - by Hunter

  I've configured Apache web server and Tomcat like this: I created a new file in apache2/sites-available, named it "myDomain" with this content: <VirtualHost *:80> ServerAdmin [email protected] ServerName myDomain.com ServerAlias www.myDomain.com ProxyPass / ajp://localhost:8009 <Proxy *> AllowOverride AuthConfig Order allow,deny Allow from all Options -Indexes </Proxy> </VirtualHost> Enabled mod_proxy and myDomain a2enmod proxy_ajp a2ensite myDomain Edited Tomcat's server.xml (inside the Engine tag) <Host name="myDomain.com" appBase="webapps/myApp"> <Context path="" docBase="."/> </Host> <Host name="www.myDomain.com" appBase="webapps/myApp"> <Context path="" docBase="."/> </Host> This works great. But I don't like to put static files (html, images, videos etc.) into {tomcat home}/webapps/myApp's subfolders instead I'd like to put them the apache webserver's root WWW directory's subdirectories. And I'd like Apache web server to serve these files alone. How could I do this? So all incoming request will be forwarded to Tomcat except those that ask for a static file.

  Read the article

• No network connection for vmware esxi guests

  - by JavaDev

  I'm new to VMware and setting up an Esxi server as a trial with the intention of possibly virtualizing some of our servers in the near future. I have setup ESXi on a Dell poweredge server, and installed a Centos 5.6 and Ubuntu 11.04 guest os on the server. However I cannot get networking on my guest OS's. The host is connected to a network with a DHCP server via a switch and is configured with a static IP. I have the default set-up for networking on the host: both guests are connected to the default vmnic1 adapter via the virtual switch vSwitch0. One thing though, the virtual adapter shows 'Observed IP ranges' to be XXX.XXX.XXX.194-XXX.XXX.XXX.195 (I've blanked out the initial prefixes) i.e just 1 address, even though the network the host is connected to has the usual 255.255.255.0 subnet mask. On the guest machines (using DHCP) by default, I can see an eth0 interface but with no connection or assigned IP address. A physical machine connected to the network gets a DHCP lease as expected. How do I get networking working on my guest OSes? Apologies for the long-winded question.

  Read the article

• Window 7 image in vmware will allow network connection out but not http

  - by Ormis

  I am currently trying to create a set of images to deploy on my network, but I've run in to a snag. When I create my own Windows 7 image I can successfully use NAT for connecting to the network but whenever I try to access a webpage I get nothing. To be more specific, All firewalls/iptables are disabled on my host machine, my virtual machine, and my network. I can do lookups and all addresses respond correctly (i'm even using Google's DNS). On the host OS i have full connectivity. On the virtual machine I can ping any device I want and all addresses resolve correctly. Within a browser I cannot reach any page via hostname or IP. I feel almost like port 80 is being blocked but i can't find any reason this would be the case. If anyone has had this occur before, I would love some insight to the problem. I initially asked this on stackoverflow and now my eyes are now opened up to superuser. Thank you for any help you can provide.

  Read the article

• pfSense routing between two routers with shared network

  - by JohnCC

  I have a network set-up using two pfSense routers arranged like this:- DMZ1 WAN1 WAN2 DMZ2 | | | | | | | | \___ PF1 PF2___/ | | | | \___TRUSTED___/ Each pfSense router has its own separate WAN connection, and a separate DMZ network attached to it. They share a common TRUSTED LAN between them. The machines on the trusted network have PF1 as their default gateway. PF1 has a static route defined to DMZ2 via PF2, and PF2 has a static route to DMZ1 via PF1. There is NAT to the WAN but internal networks (DMZ1/2 and TRUSTED) use different RFC1918 subnets. I inherited this arrangement, and all used to work fine. I made a config change to PF1 (relating to multicast), and machines on DMZ2 suddenly could not talk to TRUSTED. I rolled the change back, but the problem persisted. What I guess you'd hope would happen is that TCP packets would go DMZ2 - PF2 - TRUSTED and on return TRUSTED - PF1 - PF2 - DMZ2. That's the only way I can see it would have worked. However, PF1 drops the returning packets. I've verified this using tcpdump. I've worked around this by adding static routes to DMZ2 via PF2 to the servers on TRUSTED, but some devices on there do not support static routes so this is not ideal. Is there way to make this arrangement work decently, or is the design inherently flawed? Thanks!

  Read the article

• Windows 7 'Unidentified Network'

  - by Throdne

  So my internet was working last night before I went to bed and woke up to a computer that is showing unidentified network. I have tried multiple ways of fixing it. > route delete 0.0.0.0 > uninstalling drivers - restart - reinstall from downloaded drivers > ipconfig /release - /renew > static IP > speed & duplex from auto negotiation to 1.0gbps full duplex > and also changed my network address to no value to 1234567890ab (not in that order) nothing seems to work. I have Comcast internet and when I connect the computer to the modem it works perfectly. but when I connect it to my router again, Unidentified network. I know my router isn't faulty, because my macbook pro, server, NAS, iPhones, and iPads are still working. I have also tried moving the port on the router, still same problem. my router is a: Cisco Small Business RVS4000 motherboard: GIGABYTE GA-990FXA-UD3

  Read the article

• Strange WiFi problem - network is "not connected" but works

  - by GalacticCowboy

  Background I'm using a Windows XP tablet PC connected to my home network. I do broadcast the SSID, but otherwise the wireless network is locked down as tight as I can make it - WPA2 with a strong key, MAC filtering, etc. I've had this computer for about 4 years and the router for about 6 months. Before that, the previous router was set up in the same way, and I've never had any particular problems. Problem This morning - as I type this, as a matter of fact - Windows is reporting that none of my network connections are connected. Yet somehow my Internet connectivity still works! ipconfig reports a valid IP address, domain, etc., even though Windows apparently doesn't know about it. I tried repairing the connection and it had no effect - the repair eventually timed out. I'm pretty sure that I could reboot the computer and/or the router, etc. and it would fix the problem. However, I'm more interested in knowing if any of you have ever seen anything like this, and what might have caused it? Since it works I'm not inclined to mess with it too much. My concern is that it's a precursor to bigger problems.

  Read the article

• Windows mounted network drives slow after upgrading switch

  - by Kver

  On our small business network our old 10/100 consumer grade switch gave up the ghost, and we replaced it with a proper business-grade gigabyte switch. After wiring it in our Linux and Mac users immediately got back to working off of network drives; But 2 of our 3 Windows 7 PCs have suddenly experienced a tremendous slowdown with mapped network drives; Windows will become stuck "discovering" a folder causing applications to freeze when trying to open files. It will instantly display and browse files, but the moment you try to open one the bug hits. To remedy this we have our users copying files to the desktop, but it can take a few minutes while windows is stuck "calculating" the time it will take to copy. These aren't big files, mostly excel sheets less than 500KB - these operations are instant on Linux and Mac. (The third Windows machine is having no issues) I've tried remapping the drives, mapping to different drive letters, rebooting, etc. I'm at a loss, because switches are mostly transparent, and it's only after the switch was replaced that the Windows PCs started acting up. What black-magic voodoo am I missing to make Windows work? Thank you.

  Read the article

• Service redirection on same network

  - by Unode

  I have a network on which I run multiple servers each dedicated to a given service. Because most services run on distinct ports I'm currently looking for a way of unifying "all" services into a single "proxy" machine. The idea is to abstract which machine is being accessed but still allow direct connection if needed/requested. This "proxy" machine has only one network interface which is part of the same network as all the other service providing machines. I've looked into Routing and NAT but I've so far failed to figure out how to make it work. I tried to achieve this using shorewall but couldn't find clear examples. However I'm not entirely sure this is the best/simplest strategy. With that said, what would be the best way of achieving this result? Example case: Proxy IP - Listening port - Send requests to 192.168.0.50 80 192.168.0.1:80 " 22 192.168.0.2:2222 " 3306 192.168.0.3:3000 " 5432 192.168.0.4:5432 " 5222 192.168.0.5:5222 PS: I'm not concerned with the single-point-of-failure nature of the proxy. Thanks

  Read the article

• Having an issue trying to get Gigabit speed across my network (Ubuntu Server)

  - by user94217

  I've just started looking into the network speeds at my office, the entire network is setup to be "Gigabit". This includes Gb switches, Gb Network cards and Cat 5e cabling. I'm not expecting the full speed, I just want more than ~90 Mb/s. I've been running some tests with iperf the linux tools and checking the hardware with ethtool. I have 3 servers and when doing my checks/test I discovered that the two backup servers can access each other at around 450 Mb/s but when using either one of them to connect and test the main server, I only get the 90Mb/s even though ethtool shows the networking card running at 1000/Full. The only difference between all the server/networking cards is the "Port" which ethtool shows. On the two backup servers the "Port" is shown as MII yet on the other it's shown as "Twisted Pair". When using ethtool -s to manually set the "Port" to MII on the main server, it looses all connectivity and does not show "Speed" or "Duplex". Anyway, Am i doing something wrong? Is there a specific reason my main server cannot use Gb when there appears to be no difference except the "Port"?

  Read the article

• zsh : How to list directory content with tab?

  - by Philippe CM

  I just switched from BASH to ZSH and thing are pretty good, but: when I start typing cd /usr/share/s and hit TAB, this is what I get : $ cd /usr/share/sane/ sane/ skype/ ssl-cert/ screen/ smplayer/ strigi/ seed-gtk3/ snmp/ synaptic/ sgml/ software-properties/ system-config-printer/ sgml-base/ soprano/ sysv-rc/ sgml-data/ sounds/ simple-scan/ splashy/ And this is ok. If I then hit TAB again, I get $ cd /usr/share/screen/, the next candidate, witch is also OK. (BTW, how do I cycle back to the previous candidate? Sorry, on to my question) Now what if I want to see the contents of /usr/share/screen/ now ? You now, BASH-style? The cursor is at the end of the line, will I have to ctrl-a (or home), then del del (to erase cd) then ls then ENTER? That seems like a lot of typing. (And it - possibly unnecessarily - enters the command in the history) Would not there be a key (maybe modifier-TAB? but the obvious candidates are already taken by the desktop... I digress) that would tell zsh to stop cycling through /usr/share/ and instead, just list the content /usr/share/screen/ ?

  Read the article

• VirtualBox bridged network not working as expected

  - by iby chenko

  I am having hard time getting Bridged network to work with VirtualBox. Idea is to have host as well as one or more guests on same LAN. Using NAT (default) I do get access to internet and any node on the LAN when working from one of the VM guests. However, no LAN node including host can access (or ping) guest in VM. I need to be able to use any guest as if it was a physical computer on the network (need to be accessed by any machine on LAN). According to my understanding of the VirtualBox documentation, this should be Bridged mode. I think I set it correctly, well, actually there is not much to it: 1. select Bridged mode in VM network setup 2. select physical NIC of the host to connect bridge to 3. start VM When I do this, each VM does get new IP address that corresponds to LAN settings : 192.168.1.100 192.168.1.102 192.168.1.103 etc. where host is 192.168.1.80 / 255.255.255.0 (IP addresses above 100 are served by DHCP server). This seem to be correct based on what I know about ethernet. From VM I can ping other nodes like 192.168.1.50 etc. and I still get ethernet access. So far so good... But I STILL cannot ping any of the other VMs (running ones of course). I cannot ping them from other VMs, from host or from other nodes on the LAN. Aside from fact that IP addresses handed to guests are now local, this still acts same as NAT. What is going on? What am I missing? Regards, I

  Read the article

• how to build network across buildings ?

  - by Omie

  Hi ! I need some help in building a network between hundreds of computers spread across multiple buildings of my college. Yes, I'll be doing this as a part of my college project. Please see this image, it will give you enough idea of what I'm trying to achieve. http://i.imgur.com/rOohx.png All the computers in all buildings should be able to connect server. Once network is up, there will be a set of services over intranet and network use will be moderate. well, say there will be an email server and a http server. My point is, I cannot afford much of performance loss. It feels easy to connect computers inside 1 building to each other, however, I'm clueless as to how to connect all of them to server. I mean, just 1 cable won't be enough to connect 1 building to server, right ? How should I go with it ? I am not expecting detailed configuration. Just heads up will do :) Thanks

  Read the article

• Protocol (or service publish/discovery) to detect devices in network

  - by Gobliins

  we connect some embedded devices in a network. What i am looking for now, is a way to find the devices IP and identify them. We work with Windows PC´s and i am about to write a C# tool that should do this. I thought about send a udp broadcast and in the ack i.e. is the device´s ip, which would mean the device needs a daemon runnig to assign an ip itself. Running a service (like a printer) on the device, and on the PC just lookup for the service. I read about some things like apipa, zeroconf, ipv4 local link, bonjour, dns-sd, mdns, bonjour; They can automatically assign ip´s and publish services in a network. My Question is, can someone recommend me what would be good for my task? -The protocol or Service should be low on ressource (memory/cpu usage) use. -Are there some standard protocolls to use? -Is DNS a good idea or would it be to ressource consumpting just for finding a device´s IP? -Should also work when no dhcp servers are around. edit: To clarify a bit: The IP configuration is automatic. The problem to focus is how to tell the PC which IP in the network (or a direct connection in this vase there would only be one) belongs to the device (identity).

  Read the article

• Can't access apache from outsite my local network

  - by valter

  UPDATED: Now, when I type my external ip like xxx.xxx.xxx.xxx:8079, i can access xampp defaults page. But the strange is that when someone else from outside my network, try to access it using the same ip, it doesnt work. I Think it should, because its the external ip. I'm getting crazy. I have tried for hours to access xampp defaults page from outside my local network. My ISP blocks port 80 and 8080. So I changed apache to listen to port 8079 Listen 8079 My local computer ip is 10.1.1.2 I can access the webserver, from any computer on my local network when I type http://10.1.1.2:8079 I also oppended the port 8079 on my modem, as the image shows bellow. (I think i did it right) When apache is running on my computer, if I test the port 8079 at http://canyouseeme.org/ i get the message "Success: I can see your service on xxx.xxx.xxx.xxx on port (8079) Your ISP is not blocking port 8079" If apache is not running I get "Error: I could not see your service on xxx.xxx.xxx.xxx on port (8079) Reason: Connection refused". So, it's clear that the port 8079 is oppened. But when I type xxx.xxx.xxx.xxx:8079 on google chrome for example, I get Oops! Google Chrome could not connect to xxx.xxx.xxx.xxx:8079 What can I do to solve this, to allow apache to server the pages? I don't know what else I shoud configure. Please, help me. Thanks.

  Read the article

• How do I fix a permissions problem with MS Distributed File System?

  - by charlesrandall

  I have a computer that is new, Windows 7, that is supposed to have access to particular network resources on a Distributed File System. However, despite all permissions being set correctly, I have consistent trouble accessing them. For instance, I'm supposed to be able to reach \company.org\main\subdir. All the permissions have been granted, only when I try to access it by name, it tells me I don't have permission to access \main. This is where the fun starts. If I ping company.org, get the IP, replace company.org by the IP, I can then access \IP\main\subdir without any problems at all. However we have a ton of scripts and build tools that access the network resource by name. My sysadmin has found that using MS's dfsutil.exe, we can fix it temporary using this sequence of commands: C:\dfsutil.exe /pktinfo C:\dfsutil.exe /PktFlush C:\dfsutil.exe /SpcFlush C:\dfsutil.exe /PurgeMupCache C:\dfsutil.exe /pktinfo After that, everything is great... until I reboot, or until some unspecified time later where suddenly I don't have access to \main\ anymore. Hoping to find a more permanent solution than waiting for it to break and running a batch file.

  Read the article

• Computers on network crashing

  - by Phil Cross

  We have recently upgraded our network to Windows 7 clients with Windows server 2008 servers. The upgrade was completed by the end of September and until now has been fine (apart from the minor bugs). Recently (within the last 2 weeks) we've notice all computers on the network (around 1000) start to slow down to the point their unusable. It starts at about 08:45 and finishes at 09:15. Because of this, we think something may be broadcasting across the network. This happens every day, between these times. I cant use my computer at all at the slowdown peak, and looking at task managers performance graphs, Physical memory is hovering around 35% and CPU usage is at 0-10% (idle) yet still crashing. I've looked on DHCPs server log and cant see anything which stands out. The only change we made prior to the slowdown was installing adobe CS6 on some computers, however the slowdown affects computers without CS6. We have 2 physical machines, each with around 5-7 virtual machines running on them with ample memory. Does anyone have any suggestions as to what we can do to narrow down whats causing the crashes? Any help, suggestions or advice would be appreciated.

  Read the article

• Corrupted Laptop - Transfer Data Without My Computer (explorer.exe) Using Command Line

  - by nicorellius

  I have a laptop (Toshiba Satellite) that is pretty messed up. The person this belongs too already replaced it with a new machine. My job is to transfer all her data from this machine to disk so that I can transfer it to her. She doesn't want to lose any data (understandably so). Any operation I attempted (i.e., double clicking on any folder icon, like My Documents, My Computer, etc) resulted din a complete crash. The only good news is that I can actually start and navigate around using the command line. Also, I can access the internet. I have a network, so if I can map the drives I can get this thing figured out (hopefully). Also, I tried a USB drive but I couldn't figure out how to access it from the command line. Two questions (I need to use the command line for these): How would I go about accessing the USB drive and how can I map the shared drives on my network so that I may cd to that directory for use of the copy command?

  Read the article

• WebKit "Refused to set unsafe header "content-length"

  - by Paul

  I am trying to implement simple xhr abstraction, and am getting this warning when trying to set the headers for a POST. I think it might have something to do with setting the headers in a separate js file, because when i set them in the <script> tag in the .html file, it worked fine. The POST request is working fine, but I get this warning, and am curious why. I get this warning for both content-length and connection headers, but only in WebKit browsers (Chrome 5 beta and Safari 4). In Firefox, I don't get any warnings, the Content-Length header is set to the correct value, but the Connection is set to keep-alive instead of close, which makes me think that it is also ignoring my setRequestHeader calls and generating it's own. I have not tried this code in IE. Here is the markup & code: test.html: <!DOCTYPE html> <html> <head> <script src="jsfile.js"></script> <script> var request = new Xhr('POST', 'script.php', true, 'data=somedata', function(data) { console.log(data.text); }); </script> </head> <body> </body> </html> jsfile.js: function Xhr(method, url, async, data, callback) { var x; if(window.XMLHttpRequest) { x = new XMLHttpRequest(); x.open(method, url, async); x.onreadystatechange = function() { if(x.readyState === 4) { if(x.status === 200) { var data = { text: x.responseText, xml: x.responseXML }; callback.call(this, data); } } } if(method.toLowerCase() === "post") { x.setRequestHeader("Content-Type", "application/x-www-form-urlencoded"); x.setRequestHeader("Content-Length", data.length); x.setRequestHeader("Connection", "close"); } x.send(data); } else { // ... implement IE code here ... } return x; }

  Read the article

• Content for fans and non fans fbml?

  - by Jamie redmond

  I know that using fb:visible-to-conection allows you to display content to fans but how do I hide content from fans? Example if I have "you must be fan to view this" how do I remove that text when they are a fan? I'm using static fbml app btw. Any help appreciated.

  Read the article

• dojo/dijit ContentPane setting content

  - by Kitson

  I am trying append some XML retrieved via a dojo.XHRGet to a dijit.layout.ContentPane. Everything works ok in Firefox (3.6) but in Chrome, I only get back 'undefined' in the particular ContentPane. My code looks something like this: var cp = dijit.byId("mapDetailsPane"); cp.destroyDescendants(); // there are some existing Widgets/content I want to clear // and replace with the new content var xhrData = { url : "getsomexml.php", handleAs: "xml", preventCache: true, failOk: true }; var deferred = new dojo.xhrGet(xhrData); deferred.addCallback(function(data) { console.log(data.firstChild); // get a DOM object in both Firebug // and Chrome Dev Tools cp.attr("content",data.firstChild); // get the XML appended to the doc in Firefox, // but "undefined" in Chrome }); Because in both browsers I get back a valid Document object I know XHRGet is working fine, but there seems to be some sort of difference in how the content is being set. Is there a better way to handle the return data from the request? There was a request to see my XML, so here is part of it... <?xml version="1.0" encoding="UTF-8" standalone="no"?> <svg xmlns:svg="http://www.w3.org/2000/svg" xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink" version="1.1" width="672" height="1674"> <defs> <style type="text/css"> <![CDATA[ ...bunch of CSS... ]]> </style> <marker refX="0" refY="0" orient="auto" id="A00End" style="overflow: visible;"> ...bunch more defs... </defs> <g id="endpoints"> ...bunch of SVG with a some... <a xlink:href="javascript:gotoLogLine(16423,55);" xlink:type="simple">...more svg...</a> </g> </svg> I have run the output XML trough the WC3 validator for XML to verify it is valid. Like I said before, works in FireFox 3.6. I tried it on Safari and I got the same "undefined" so it seems to be related to Webkit.

  Read the article

• Show Content from other websites using RSS in my Drupal Site

  - by Vivek Chandraprakash

  Hi, I would like to show content from other websites using RSS Feeds into my drupal site and show it inside a page. I searched for RSS. There are so many. Can you suggest a good one? I'm trying to show the content from here http://feeds.feedburner.com/brazen_careerist Thanks a lot -Vivek

  Read the article

< Previous Page | 133 134 135 136 137 138 139 140 141 142 143 144  | Next Page >