Search Results

Search found 12281 results on 492 pages for 'ip blocking'.

Page 138/492 | < Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >

• OS X - forwarding external port to local loopback address

  - by Rory Fitzpatrick

  I have an HTTP service bound to port 8000 that I want to access from another computing on the network, but I can't seem to connect using the external IP address of the machine (e.g. 192.168.0.105). I've checked the OS X firewall isn't running, so I'm assuming the issue is the service is only bound to the IP address 127.0.0.1, and not the external IP address. What would be the easiest way to temporarily forward external connections on port 8000 to 127.0.0.1:8000?

  Read the article

• Routing public IPs (each a /32) through a VPN to another server

  - by Lee S

  Hopefully the title makes sense; I have a server currently in a colo facility, with many IP addresses routed to it. They are individual IPs and not in a contiguous block. Due to vastly improved connectivity (fibre) at home I am slowly bringing my infrastructure in-house for managability and eventually, cost savings. What I would like to do though is use the IP addresses allocated to my existing server, at home. I have an IP block allocated to me on my new ISP connection, but for a couple of reasons I'd like to make use of the colo ones for now: Ease of transition - lots of domains, dns, hard-coded IPs in programs, etc. Connectivity fallback. If my primary line goes down and switches to fallback 1 (dsl) or fallback 2 (4G), I lose access to the ISP-allocated IP block of IPs that are only presented on the primary WAN interface. What I'd like to achieve is my home virtualisation server (Proxmox/Debian-based) "dials in" to the colo server in the colo facility (also Proxmox/Debian) via VPN or similar, and gets to make use of the IP addresses that currently terminate on the colo box. If the primary connection to my ISP goes down and one of the fallback routes kicks in, the VPN tunnel will just time out and then be re-established on the backup connection instead. I'm sure this is doable, but I have no idea how. I'm not afraid to get my hands dirty, I just don't really know where to start?

  Read the article

• Nameserver Problem

  - by Ruel

  I installed Virtualmin GPL with BIND, etc. I created a virtual host for my main domain, and edited the zone file, added the A records for the nameservers ns1.mydomain.com and ns2.mydomain.com. All looks good from the VPS, whenever I do a dig or nslookup, all seems fine, returning correct details. But when I test externally, there are no results. I tried several sites such as intodns, etc. It says my nameservers doesn't point to any IP. I have registered my nameservers with the appropriate IP in my registrar, and I even contacted support to verify this, and they told me that the registration was successful, but when they dig my nameservers, there's no ip address. I can also connect to my server IP's port 53. Also, I know that the DNS propagation is 24-48 hours. But there has to be some server that can return the correct results by now. Please lead me to the right direction, thanks.

  Read the article

• route http and ssh traffic normally, everything else via vpn tunnel

  - by Normadize

  I've read quite a bit and am close, I feel, and I'm pulling my hair out ... please help! I have an OpenVPN cliend whose server sets local routes and also changes the default gw (I know I can prevent that with --route-nopull). I'd like to have all outgoing http and ssh traffic via the local gw, and everything else via the vpn. Local IP is 192.168.1.6/24, gw 192.168.1.1. OpenVPN local IP is 10.102.1.6/32, gw 192.168.1.5 OpenVPN server is at {OPENVPN_SERVER_IP} Here's the route table after openvpn connection: # ip route show table main 0.0.0.0/1 via 10.102.1.5 dev tun0 default via 192.168.1.1 dev eth0 proto static 10.102.1.1 via 10.102.1.5 dev tun0 10.102.1.5 dev tun0 proto kernel scope link src 10.102.1.6 {OPENVPN_SERVER_IP} via 192.168.1.1 dev eth0 128.0.0.0/1 via 10.102.1.5 dev tun0 169.254.0.0/16 dev eth0 scope link metric 1000 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.6 metric 1 This makes all packets go via to the VPN tunnel except those destined for 192.168.1.0/24. Doing wget -qO- http://echoip.org shows the vpn server's address, as expected, the packets have 10.102.1.6 as source address (the vpn local ip), and are routed via tun0 ... as reported by tcpdump -i tun0 (tcpdump -i eth0 sees none of this traffic). What I tried was: create a 2nd routing table holding the 192.168.1.6/24 routing info (copied from the main table above) add an iptables -t mangle -I PREROUTING rule to mark packets destined for port 80 add an ip rule to match on the mangled packet and point it to the 2nd routing table add an ip rule for to 192.168.1.6 and from 192.168.1.6 to point to the 2nd routing table (though this is superfluous) changed the ipv4 filter validation to none in net.ipv4.conf.tun0.rp_filter=0 and net.ipv4.conf.eth0.rp_filter=0 I also tried an iptables mangle output rule, iptables nat prerouting rule. It still fails and I'm not sure what I'm missing: iptables mangle prerouting: packet still goes via vpn iptables mangle output: packet times out Is it not the case that to achieve what I want, then when doing wget http://echoip.org I should change the packet's source address to 192.168.1.6 before routing it off? But if I do that, the response from the http server would be routed back to 192.168.1.6 and wget would not see it as it is still bound to tun0 (the vpn interface)? Can a kind soul please help? What commands would you execute after the openvpn connects to achieve what I want? Looking forward to hair regrowth ...

  Read the article

• Can I limit remote desktop to a particular network card?

  - by Jack Mills

  I have two routers/internet connections connected to my PC. One is a slower connection with a fixed IP that I use for business, the other is a faster connection I use for day to day surfing. I have to use the fixed IP connection to log onto certain servers (due to security) to work but I'm finding that often my PC will try to use my other internet connection to connect which will get rejected (as it doesn't have the fixed IP). Can I limit remote desktop to use a particular network card to get around this problem. Note: I'm running Windows 7

  Read the article

• Home Network Stopped Working

  - by James

  I have a home network where a machine running Windows 7 Ultimate N acts as a central hub for other devices to access media. This has been running for around 2 years now and there has been no recent configuration changes. The machine has a static IP address (192.168.0.3), which also has not been changed. A few laptops, Sonos music system and mobiles are using the machine for music/video mostly. Additionally, post 3389 was also open for RDP. I used a no-ip agent to map a hostname so I could RDP to the machine from the internet. As of yesterday when I try to ping the machine, I get PING:Transmit Failed, General Error I noticed however, the IP it is pinging is 0.0.2.233. All shares etc are no longer functioning including RDP. On the machine itself, an IP config shows like nothing has changed. It still shows the expected IP. If I ping itself from its hostname, I get the same error as above. machine has been rebooted, the router has been also. Any ideas where to even start on this?

  Read the article

• Cannot connect to apache web server over internet

  - by user1658093

  I can access my apache 2.2 webserver from the lan ( at this case I use local IP aadress ) but I cannot connect externally ( from another network ). I changed apache to listen port 800, forwarded same port from router control panel, turned off windows and router firewalls. I use whatsmyip.com to get IP with what I try to connect. When I'm trying to connect I use : [whatsmyip.com IP]:800. Also, I can ping server IP externally. OS is windows7. Any ideas, suggestions? Thanks

  Read the article

• Windows remote shutdown: access denied

  - by gregseth

  I have 3 "client" computers, on which the mentioned user is administrator: CPU1: Win Vista 32-bit -- User: Domain\User1 -- IP: 192.168.42.1 CPU2: Win 7 64-bit -- User: localhost\User2 -- IP: 192.168.42.2 CPU3: Win 7 64-bit -- User: Domain\User3 -- IP: 192.168.42.3 And a "target" computer (the one that I want to shutdown from the three others): TGT: Win 7 64-bit -- User: localhost\User4 -- IP: 192.168.42.21 I'm trying to shutdown TGT with the following command: shutdown /s /m \\192.168.42.21 It's working from CPU1 (meaning TGT shuts down), but from CPU2 and CPU3 I get the following message: Access denied. (5) What am I to understand? What should I do to get it working form all of my computers.

  Read the article

• Games consoles won't connect through the TP-Link TL-WA500G Access Point

  - by Manfred Wolff

  I hope that someone can help me. I have several Laptops and other devices, all using my Wireless Router (Sky Digital Netgear) To extend the range to the back of the house, I purchased a TP-Link TL-WA500G Range extender. configured just as a pure repeater, it picks up the signal from the Netgear Router. The Netgear Router does the DHCP, handing out the IP addresses. This all works a treat with several different laptops and my iPone4S, but when my son tries to use his XBox360, Sony Playstation3 or the Nintendo Wii those devices fail to acquire an IP address. They just sit their waiting for the IP config. This also happens with my wife's HTC desire ONE Android phone. My son says that, when his HTC Desire C won't get an IP address, he just unplugs the AP briefly - the phone will connect and he puts the AP back on. Once he is connected to the Router, the AP won't disturb function. The Games Consoles don't seem to work like that. They stop working, when the AP is reconnected. I had my son try to configure permanent IP addresses, and he said that did not work either, though I have to confirm that, as I did not see that for myself. Has anybody seen this before? I have searched the Net and have not found any similar problems anywhere. I wonder if there is setting somewhere that would fix this. Many thanks for anyone reading this and trying to help. M

  Read the article

• How to configure a static wildcard subdomain with dnsmasq.

  - by Prody

  I have a network behind a NAT with a few machines. The machines are: router - NAT, dnsmasq, forwarding - directly connected to the inet server - which runs ssh, www and some other stuff clients - which do stuff on server I also have mydomain.com. server.mydomain.com is pointing to my connection's IP (single IP), which is the router, which forwards ports to server. Server, has a httpd running, which serves different sites based on vhosts. So I have site1.server.mydomain.com, site2.. The problem is that all the traffic is going thru the router, and when I check logs I always see the router's IP for everything (so it's hard to see who is running the script with the while(1)). I would just ServerAlias site1.server.local, but most of the sites have a root URL saved somewhere on top of which other URLs are built, so I can't do that. The solution for me would be telling dnsmasq somehow to answer to *.mydomain.com with server's IP. Is this possible somehow?

  Read the article

• Cisco 1841 and routing /29 address

  - by Jonathan

  Could someone please explain in general terms how I'd configure a Cisco 1841 (2x ethernet ports) to route a public /29 address block (6 hosts) to my internal network. I wish to give the Cisco router one public IP and then several of my internal Windows servers will receive the other public IP addresses. Other hosts behind the router will access Internet via NAT. I'm a bit confused as I've only ever setup routers/firewalls that had a single public IP address with NAT and port forwarding to internal servers.

  Read the article

• How to access this server?

  - by George Edison

  I have a server that I cannot access. At first I thought it was just some temporary failure with the server, but checking from other IP addresses reveals that it is working just fine. It's only my IP address that's failing. So here is what I've tried: nslookup - resolves correctly ping - 100% packet loss using the IP address or domain traceroute - first few hops work, but from about 6 and on, I just get stars Edit: I am using OpenDNS for DNS resolution, and as mentioned above, the problem is not DNS resolution anyway.

  Read the article

• LXC Container Networking

  - by digitaladdictions

  I just started to experiment with LXC containers. I was able to create a container and start it up but I cannot get dhcp to assign the container an IP address. If I assign a static address the container can ping the host IP but not outside the host IP. The host is CentOS 6.5 and the guest is Ubuntu 14.04LTS. I used the template downloaded by lxc-create -t download -n cn-01 command. If I am trying to get an IP address on the same subnet as the host I don't believe I should need the IP tables rule for masquerading but I added it anyways. Same with IP forwarding. I compiled LXC by hand from the following source https://linuxcontainers.org/downloads/lxc-1.0.4.tar.gz Host Operating System Version #> cat /etc/redhat-release CentOS release 6.5 (Final) #> uname -a Linux localhost.localdomain 2.6.32-431.20.3.el6.x86_64 #1 SMP Thu Jun 19 21:14:45 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux Container Config #> cat /usr/local/var/lib/lxc/cn-01/config # Template used to create this container: /usr/local/share/lxc/templates/lxc-download # Parameters passed to the template: # For additional config options, please look at lxc.container.conf(5) # Distribution configuration lxc.include = /usr/local/share/lxc/config/ubuntu.common.conf lxc.arch = x86_64 # Container specific configuration lxc.rootfs = /usr/local/var/lib/lxc/cn-01/rootfs lxc.utsname = cn-01 # Network configuration lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 LXC default.confu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:f #> cat /usr/local/etc/lxc/default.conf lxc.network.type = veth lxc.network.link = br0 lxc.network.flags = up #> lxc-checkconfig Kernel configuration not found at /proc/config.gz; searching... Kernel configuration found at /boot/config-2.6.32-431.20.3.el6.x86_64 --- Namespaces --- Namespaces: enabled Utsname namespace: enabled Ipc namespace: enabled Pid namespace: enabled User namespace: enabled Network namespace: enabled Multiple /dev/pts instances: enabled --- Control groups --- Cgroup: enabled Cgroup namespace: enabled Cgroup device: enabled Cgroup sched: enabled Cgroup cpu account: enabled Cgroup memory controller: /usr/local/bin/lxc-checkconfig: line 103: [: too many arguments enabled Cgroup cpuset: enabled --- Misc --- Veth pair device: enabled Macvlan: enabled Vlan: enabled File capabilities: /usr/local/bin/lxc-checkconfig: line 118: [: -gt: unary operator expected Note : Before booting a new kernel, you can check its configuration usage : CONFIG=/path/to/config /usr/local/bin/lxc-checkconfig Network Config (HOST) #> cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE=br0 TYPE=Bridge BOOTPROTO=dhcp ONBOOT=yes #> cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 ONBOOT=yes TYPE=Ethernet IPV6INIT=no USERCTL=no BRIDGE=br0 #> cat /etc/networks default 0.0.0.0 loopback 127.0.0.0 link-local 169.254.0.0 #> ip a s 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:ff:ff inet6 fe80::20c:29ff:fe12:30f2/64 scope link valid_lft forever preferred_lft forever 3: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 42:7e:43:b3:61:c5 brd ff:ff:ff:ff:ff:ff 4: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 00:0c:29:12:30:f2 brd ff:ff:ff:ff:ff:ff inet 10.60.70.121/24 brd 10.60.70.255 scope global br0 inet6 fe80::20c:29ff:fe12:30f2/64 scope link valid_lft forever preferred_lft forever 12: vethT6BGL2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether fe:a1:69:af:50:17 brd ff:ff:ff:ff:ff:ff inet6 fe80::fca1:69ff:feaf:5017/64 scope link valid_lft forever preferred_lft forever #> brctl show bridge name bridge id STP enabled interfaces br0 8000.000c291230f2 no eth0 vethT6BGL2 pan0 8000.000000000000 no #> cat /proc/sys/net/ipv4/ip_forward 1 # Generated by iptables-save v1.4.7 on Fri Jul 11 15:11:36 2014 *nat :PREROUTING ACCEPT [34:6287] :POSTROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A POSTROUTING -o eth0 -j MASQUERADE COMMIT # Completed on Fri Jul 11 15:11:36 2014 Network Config (Container) #> cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp #> ip a s 11: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 02:69:fb:42:ee:d7 brd ff:ff:ff:ff:ff:ff inet6 fe80::69:fbff:fe42:eed7/64 scope link valid_lft forever preferred_lft forever 13: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever

  Read the article

• Is there a Linux kernel boot parameter to configure an IPv6 address?

  - by aef

  I know there is a parameter named ip which lets you configure IPv4 addresses on the Linux kernel through the boot loader. That looks like the following: ip=192.0.2.1::192.0.2.62:255.255.255.192::eth0:none I'm looking for an equal parameter for IPv6 configuration. I couldn't find anything about this in the kernel documentations. Update: Because of a lot of you asked why I would need this: The idea to use a kernel configuration came up related to this problem. I suspect the regular boot-up interface configuration is not done, because the interfaces are already up. The reason for this could be that I'm using a pre-boot environment with a Dropbear SSH server to allow me to unlock my encrypted root partition. The IP addresses for this environment are configured through GRUB with the ip= parameter. There is no DHCP or Router Advertisement available on that Ethernet segment and as this is the uplink segment provided by a large hosting company, there is no way to change that fact.

  Read the article

• If I ssh to a domain provided by dyndns, does my password go through them?

  - by D Connors

  I'm running Ubuntu on my work PC, and my work place provides me with a static IP address but not with a domain. It's sometimes useful for me to connect to that PC through ssh, but it's not common enough for me to instantly remember the IP number. So I set um a dyndns account, and associated a short and intuitive domain name to that IP. Here's my question, when I try to ssh to the domain, it asks me $ ssh [email protected] The authenticity of host 'something.there.foo (xx.xx.xx.xx)' can't be established. RSA key fingerprint is 'ALPHANUMERIC STRING' Are you sure you want to continue connecting (yes/no)? That surprised me a little bit. I have already registered the RSA fingerprint by connecting directly to the IP address. I thought the domain name was simply a convenient way of pointing me in the right direction (i. e. the ip address), but that message makes me think my data is actually going through their servers or something. Which one is it? Am I sending my password through someone else's server? Or is ssh just really really careful, thus warning me even if the final destination is a know host? The ssh server I'm using is the openssh-server package.

  Read the article

• Uninstalled server 2008 now router won't handle DHCP

  - by john

  My set up is this. server behind router, router has a server and switch connected to it with multiple computers. router used to serve DHCP and DNS, a couple of days ago installed AD, DNS and DHCP on the server, and the server gave out IP's. For various reasons we had to uninstall the domain on our server. I removed AD, DHCP and DNS from the roles and set the router back to serving DHCP and DNS. Now I can't get computers on the network. I reset my router back to factory defaults, and if I plug a computer directly into the router I can get a IP address, but all the computers behind the switch can't get an IP address and can't see the router. All my computers say unidentified network, and if I ping the router it says host is unreachable. On the other hand, my wireless devices are just fine and connect no problem. But for desktops, ipconfig /release doesn't release anything and /renew can't find a server to renew on. My router log shows several FIN scans but they are from innocuous websites (google, netgear) and it shows a couple of smurf attacks but they are all from my external IP. Any ideas? the server isn't even connected to the route right now, and all the computers are set for dynamic IP addresses.. I don't know what else to try? Any help?

  Read the article

• Multiple IPs from one router

  - by ergoen

  I would like to know if it is possible (and if so, how) to configure a router running dd-wrt (or openwrt) to supply connected devices with two ip addresses. The network looks like this: [Internet] | [Router] | | [Comp1] [Comp2] ... My ISP provides me with enough public IP adresses to give all devices on my network one each. The easiest way to set that up is to just use the router as a switch. This will however lead to problems with some LAN based applications. I would still like to use Samba-shares between the computers as well as a vpn server. What I am looking for basically is if it is possible to use the router as a DHCP server for a local network (let's say giving IP adresses 192.168.1.xx to connected computers) while at the same time passing through public IP addresses to each as well?

  Read the article

• Configuring bridged network connection --- Windows 7 host, Ubuntu 10.04 guest --- VMWare Workstation 8

  - by H3br3wHamm3r81

  Here is my IPCONFIG /ALL from the host (Windows 7 64-bit): Here is my IFCONFIG from the guest (Ubuntu 10.04): To be honest, I don't have experience configuring a network between a host and a guest in VMWare (a virtual machine). I've searched high and low on the internet, but I haven't seen anything that can help. Perhaps I'm just not using the right keywords when I search. Nevertheless, does anyone here have any experience with establishing a network connection? Edit: One important note. I don't use DHCP to provide private addresses to the hosts on my LAN. I use "static" IP addresses on my internal network by configuring each IP address manually in the host's network configuration utility (I have TV's, XBOX 360, and a few PC's). I would like to configure the IP on the virtual machine guest manually as well. The reason is because my XBOX 360 only works properly using a static IP address. It will kick me off XBOX Live if it has one given by the router (via DHCP).

  Read the article

• Squid3 not working. Access denied

  - by Nitish

  I installed SQUID3 on a Linux machine with two ethernet interfaces (eth0 and eth1). I used the default settings in the squid.conf file and uncommented the two lines acl localnet src 192.168.0.0/16 and http_access allow localnet. eth0 is connected to a router, which provides Internet access. It is assigned an IP 192.168.1.2 by the router. I manually configured eth1 to have an IP address 192.168.5.1. It is connected to a switch. Systems having IP addresses 192.168.5.x are connected to this switch. I ran these two commands for NAT: iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.5.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 But when I try to access internet from a system having IP 192.168.5.2 through the proxy I get an error that says "Access denied". What is wrong with my configuration?

  Read the article

• dhcp code for pxe server

  - by avoq

  I'm trying to understand every single line of the following script but to no avail. I'd be glad if someone could help me. For sure I know its purpose is to start the DHCP server as well as the TFTP...But I'm stuck: killall dnsmasq 2>/dev/null dnsmasq --enable-tftp --tftp-root=$PXEDATA/boot --dhcp-boot=pxelinux.0,"$IP",$IP --dhcp-range=$(echo $IP | cut -d. -f1-3).50,$(echo $IP | cut -d. -f1-3).250, infinite --dhcp-option=option:router,192.168.0.254 --log-dhcp Why killall, why dnsmasq 2 What does "2" stand for? "--" what does it mean? Thanks a lot.

  Read the article

• Setting a subdomain to access home machine with windows remote desktop

  - by ianhales

  I'm trying to remotely connect to home machine through Windows Remote Desktop (amongst other things, but this is currently my primary focus). I can do this fine using my home WAN's static IP (thank god for cable!) with port-forwarding, but I would like to access it from a subdomain of my web-site (e.g. home.mydomain.co.uk). In the cPanel for my hosting account, I've gone into DNS zones and altered the A-record to point to my WAN's IP, which I thought should do the job, but I still cannot connect. When I ping the subdomain, I get my web-host's IP, which I guess is to be expected as I believe the DNS of the host domain is used first, then my server handles the redirection of traffic to the IP in the A-record. Is this the correct idea? Do A-record changes suffer from the same propagation delays as DNS record changes, as I suppose that could explain it? (by the way, this thread confirms my thoughts that setting the A-record should be enough: Hostmonster Subdomain redirected to home server IP: How to ssh into home server using subdomain)

  Read the article

• How do I connect remotely to SQL Server from Windows client?

  - by humble_coder

  Hi All, Having a bit of an issue connecting to SQL SERVER remotely from Windows. I've verified that all of my settings are correct via SQL SERVER MANAGEMENT STUDIO EXPRESS and SQL SERVER CONFIGURATION MANAGER. I can connect remotely using ODBC drivers from other OSes (e.g. OS X, Linux, etc). However, when I connect with the same credentials from a remote Windows machine using "SQL SERVER" as the driver I am told that the system cannot connect. I've tried creating an ODBC Data Source and I get the same error: Connection failed: SQLState: '01000' SQL Server Error: 14 [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]ConnectionOpen(InvalidInstance()). Connection failed: SQLState: '08001' SQL Server Error: 14 [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]Invalid Connection From the non-windows machines I can use the IP address of the SQL Server just fine. However, on the remote Windows machine, neither IP address nor named instance works. FYI, I can create an ODBC Data Source using the named instance on the machine actually running the SQL Server (but this is, of course, nothing special -- just proof that it isn't completely hosed). One interesting note: If I use SQL STUDIO 2005 from a Windows client machine, I can use the IP address to connect remotely. Still, the whole reason I bring this up is because I need to use a software package I've written to connect to SQL Server remotely from Windows machines as well. Previously the solution was only needed to xfer data from SQL Server into a PostGRES or MySQL database on non-Windows machines (due to DBA preference). However, now they also want to move the data from the legacy software to MySQL even on Windows. Any assistance would be most appreciated. Feel free to provide a full example connection string. Best

  Read the article

• Mod_security Logging

  - by Hekuran S. Doli

  Im trying to run mod_security as standalone service with nginx as reverse proxy everything works fine except logging. Mod_security logs reverse proxys ip addres instead of clients ip address. I would appreciate if someone can help. The following is an example of logfile where mod_security is logging 127.0.0.1 instead of clients ip address. 2012/08/29 14:18:13 [info] 206862#0: [client 127.0.0.1] ModSecurity: Access denied with code 403 (phase 2). Pattern match ...

  Read the article

• Forwarding subdomain to different port on Windows IIS 7

  - by Ralph

  I have a IIS 7 server with Plesk setup on a Windows 2008 R2 server and I have created a subdomain sub1.domain.com, which by default leads to my webserver on port 80, but I don't want that. I want the subdomain to lead to my port 25566 instead (for a Minecraft server), how can I accomplish this? I tried this with host headers / bindings but that resulted in a port already in use warning. How can I do this? How can I make my sub1.domain.com lead to IP.IP.IP.IP:25566? Any help would be greatly appreciated.

  Read the article

• Ping reply not getting to LAN machines but getting in Linux router Gateway

  - by Kevin Parker

  I have configured Ubuntu 12.04 as Gateway machine.its having two interfaces eth0 with ip 192.168.122.39(Static) and eth1 connected to modem with ip address 192.168.2.3(through DHCP). ip-forwarding is enabled in router box. Client machine is configured as: ip address 192.168.122.5 and gateway 192.168.122.39 Client machines can ping router box(192.168.122.39).but when pinged 8.8.8.8 reply is not reaching Client machines but in the tcpdump output on gateway i can see echo request for 8.8.8.8 but never echo reply.Is this because of 122.5 not forwarding request to 2.0 network.Can u please help me in fixing this.

  Read the article

< Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >