Search Results

Search found 3898 results on 156 pages for 'unknown'.

Page 138/156 | < Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >

• Confusion on networking service start/stop in Ubuntu

  - by Daniel Ball

  I'm preparing to move and took down two of my servers, leaving only one with some essential services running. What I neglected to consider was that one was the DHCP server(which I realized when somebody contacted me saying they couldn't connect. Whups). So because I only have a few hosts on this small network, I opted to just statically configure them for now. One of these is a new Ubuntu 11.04 server, where I have very little experience. I edited /etc/network/interfaces and /etc/hosts to reflect my changes. I ran $sudo /etc/init.d/networking stop *deconfiguring network interfaces ... So yay. Then I try to start, it gives me the mumbo jumbo about using services (why didn't it do that for the stop?) So instead I run ... $sudo service networking start networking stop/waiting Now, to me that says the status of the service is stopped. But when I ping another computer, I get a successful reply. So is it not actually stopped? More importantly, am I doing something wrong? Edit daniel@FOOBAR:~$ sudo service networking status networking stop/waiting daniel@FOOBAR:~$ sudo service networking stop stop: Unknown instance: daniel@FOOBAR:~$ sudo service networking status networking stop/waiting daniel@FOOBAR:~$ sudo service networking start networking stop/waiting daniel@FOOBAR:~$ sudo service networking status networking stop/waiting So you can see why I ran /etc/init.d/networking stop instead. For some reason upstart (that is what "services" is, right?) isn't working with stop. cat /etc/hosts 127.0.0.1 localhost 127.0.1.1 FOOBAR 198.3.9.2 FOOBAR #Added entry July 19 2011 # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface #auto eth0 #iface eth0 inet dhcp # hostname FOOBAR auto eth0 iface eth0 inet static address 198.3.9.2 netmask 255.255.255.0 network 198.3.9.0 broadcast 198.3.9.255 gateway 198.3.9.15 No I didn't save backups, it was just a minor change so I just commented out the old DHCP setting. Edit I set everything back to original settings and set up a DHCP server. "starting" networking does the same thing. I can only assume this is normal, I just don't know WHY. It can't be anything to do with the configuration files, since they've been restored.

  Read the article

• VirtualBox guest responds to ping but all ports closed in nmap

  - by jeremyjjbrown

  I want to setup a test database on a vm for development purposes but I cannot connect to the server via the network. I've got Ubuntu 12.04vm installed on 12.04 host in Virtualbox 4.2.4 set to - Bridged network mode - Promiscuous Allow All When I try to ping the virtual guest from any network client I get the expected result. PING 192.168.1.209 (192.168.1.209) 56(84) bytes of data. 64 bytes from 192.168.1.209: icmp_req=1 ttl=64 time=0.427 ms ... Internet access inside the vm is normal But when I nmap it I get nothin! jeremy@bangkok:~$ nmap -sV -p 1-65535 192.168.1.209 Starting Nmap 5.21 ( http://nmap.org ) at 2012-11-15 18:39 CST Nmap scan report for jeremy (192.168.1.209) Host is up (0.0032s latency). All 65535 scanned ports on jeremy (192.168.1.209) are closed Service detection performed. Please report any incorrect results at http://nmap.org/submit/ Nmap done: 1 IP address (1 host up) scanned in 0.88 seconds ufw and iptables on VM... jeremy@jeremy:~$ sudo service ufw stop [sudo] password for jeremy: ufw stop/waiting jeremy@jeremy:~$ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I have scanned around and have no reason to believe that my router is blocking internal ports. jeremy@bangkok:~$ nmap -v 192.168.1.2 Starting Nmap 5.21 ( http://nmap.org ) at 2012-11-15 18:44 CST Initiating Ping Scan at 18:44 Scanning 192.168.1.2 [2 ports] Completed Ping Scan at 18:44, 0.00s elapsed (1 total hosts) Initiating Parallel DNS resolution of 1 host. at 18:44 Completed Parallel DNS resolution of 1 host. at 18:44, 0.03s elapsed Initiating Connect Scan at 18:44 Scanning 192.168.1.2 [1000 ports] Discovered open port 445/tcp on 192.168.1.2 Discovered open port 139/tcp on 192.168.1.2 Discovered open port 3306/tcp on 192.168.1.2 Discovered open port 80/tcp on 192.168.1.2 Discovered open port 111/tcp on 192.168.1.2 Discovered open port 53/tcp on 192.168.1.2 Discovered open port 5902/tcp on 192.168.1.2 Discovered open port 8090/tcp on 192.168.1.2 Discovered open port 6881/tcp on 192.168.1.2 Completed Connect Scan at 18:44, 0.02s elapsed (1000 total ports) Nmap scan report for 192.168.1.2 Host is up (0.0017s latency). Not shown: 991 closed ports PORT STATE SERVICE 53/tcp open domain 80/tcp open http 111/tcp open rpcbind 139/tcp open netbios-ssn 445/tcp open microsoft-ds 3306/tcp open mysql 5902/tcp open vnc-2 6881/tcp open bittorrent-tracker 8090/tcp open unknown Read data files from: /usr/share/nmap Nmap done: 1 IP address (1 host up) scanned in 0.08 seconds Answer... Turns out all of the ports were open to the network. I installed open ssh and confirmed it. Then I edited my db conf to listen to external IP's and all was well.

  Read the article

• Error 80073701 when installing Windows 7 Service Pack 1

  - by Wagner Maestrelli

  I tried to install the Windows 7 Service Pack 1 using Windows Update and I got an error (code 80073701 - unknown error). I tried it again, same thing. Rebooted and tried again, same error. Before I tried to install the SP1 I had installed all the previous updates. I have Windows 7 Ultimate 32-bits. Has anyone gone through the same problem? Any ideas of what might be happening? Thanks! UPDATE: I installed the System Update Readiness Tool. Then, I tried to install the SP1 again, but the installation failed again with the same error. As I thought I was running out of options, I downloaded the SP1 package (500+ MB) and tried to install manually. Before that, I reinstalled the SUR Update. Well, the manual installation of the SP1 failed again. Then I learned about the c:\Windows\Logs\CBS\CheckSUR.log file (thanks Patches!). I checked it out. As I installed the SUR Update multiple times, the older logs are kept in the c:\Windows\Logs\CBS\CheckSUR.persist.log file. In the first time the SUR update was installed there was an error, which is said to have been fixed. In the subsequent logs, no errors were detected. The log with the error: ================================= Checking System Update Readiness. Binary Version 6.1.7600.20593 Package Version 7.0 2010-03-19 09:57 Checking Windows Servicing Packages Checking Package Manifests and Catalogs (f) CBS MUM Corrupt 0x800B0100 servicing\Packages\Microsoft-Windows-Client-LanguagePack-Package~31bf3856ad364e35~x86~pt-BR~6.1.7600.16385.mum servicing\Packages\Microsoft-Windows-Client-LanguagePack-Package~31bf3856ad364e35~x86~pt-BR~6.1.7600.16385.cat Package manifest cannot be validated by the corresponding catalog (fix) CBS MUM Corrupt CBS File Replaced Microsoft-Windows-Client-LanguagePack-Package~31bf3856ad364e35~x86~pt-BR~6.1.7600.16385.mum from Cabinet: C:\Windows\CheckSur\v1.0\windows6.1-rtm-client-cab3-x86.cab. (fix) CBS Paired File CBS File also Replaced Microsoft-Windows-Client-LanguagePack-Package~31bf3856ad364e35~x86~pt-BR~6.1.7600.16385.cat from Cabinet: C:\Windows\CheckSur\v1.0\windows6.1-rtm-client-cab3-x86.cab. Checking Package Watchlist Checking Component Watchlist Checking Packages Checking Component Store Summary: Seconds executed: 224 Found 1 errors Fixed 1 errors CBS MUM Corrupt Total count: 1 Fixed: CBS MUM Corrupt. Total count: 1 Fixed: CBS Paired File. Total count: 1 It seems it has something to do with the Brazilian Portuguese Language Pack, which happens to be my native language. Problem is I can't uninstall the language pack since it is my system default language. And I haven't found any place to download it so I could reinstall it manually. Well, any ideas? Thanks!

  Read the article

• Indirect Postfix bounces create new user directories

  - by hheimbuerger

  I'm running Postfix on my personal server in a data centre. I am not a professional mail hoster and not a Postfix expert, it is just used for a few domains served from that server. IIRC, I mostly followed this howto when setting up Postfix. Mails addressed to one of the domains the server manages are delivered locally (/srv/mail) to be fetched with Dovecot. Mails to other domains require usage of SMTPS. The mailbox configuration is stored in MySQL. The problem I have is that I suddenly found new mailboxes being created on the disk. Let's say I have the domain 'example.com'. Then I would have lots of new directories, e.g. /srv/mail/example.com/abenaackart /srv/mail/example.com/abenaacton etc. There are no entries for these addresses in my database, neither as a mailbox nor as an alias. It's clearly spam from auto-generated names. Most of them start with 'a', a few with 'b' and a couple of random ones with other letters. At first I was afraid of an attack, but all security restrictions seem to work. If I try to send mail to these addresses, I get an "Recipient address rejected: User unknown in virtual mailbox table" during the 'RCPT TO' stage. So I looked into the mails stored in these mailboxes. Turns out that all of them are bounces. It seems like all of them were sent from a randomly generated name to an alias that really exists on my system, but pointed to an invalid destination address on another host. So Postfix accepted it, then tried to redirect it to another mail server, which rejected it. This bounced back to my Postfix server, which now took the bounce and stored it locally -- because it seemed to be originating from one of the addresses it manages. Example: My Postfix server handles the example.com domain. [email protected] is configured to redirect to [email protected]. [email protected] has since been deleted from the Hotmail servers. Spammer sends mail with FROM:[email protected] and TO:[email protected]. My Postfix server accepts the mail and tries to hand it off to hotmail.com. hotmail.com sends a bounce back. My Postfix server accepts the bounce and delivers it to /srv/mail/example.com/bob. The last step is what I don't want. I'm not quite sure what it should do instead, but creating hundreds of new mailboxes on my disk is not what I want... Any ideas how to get rid of this behaviour? I'll happily post parts of my configuration, but I'm not really sure where to start debugging the problem at this point.

  Read the article

• IIS6 Virtual Directory 500 Error on Remote Share

  - by David

  We have our servers at the server farm in a domain. Let's call it LIVE. Our developer computers live in a completely separate corporate domain, miles and miles away. Let's call it CORP. We have a large central storage unit (unix) that houses images and other media needed by many webservers in the server farm. The IIS application pools run as (let's say) LIVE\MediaUser and use those credentials to connect to a central storage share as a virtual directory, retrieve the images, and serve them as if they were local on each server. The problem is in development. On my development machine. I log in as CORP\MyName. My IIS 6 application pool runs as Network Service. I can't run it as a user from the LIVE domain because my machine isn't (and can not be) joined to that domain. I try to create a virtual directory, point it to the same network directory, click Connect As, uncheck the "Always use the authenticated user's credentials when validating access to the network directory" checkbox so that I can enter the login info, enter the credentails for LIVE\MediaUser, click OK, verify the password, etc. This doesn't work. I get "HTTP Error 500 - Internal server error" from IIS. The IIS log file reports sc-status = 500, sc-substatus = 16, and sc-win32-status = 1326. The documentation says this means "UNC authorization credentials are incorrect" and the Win32 status means "Logon failure: unknown user name or bad password." This would be all and good if it were anywhere close to accurate. I double- and trouble-checked it. Tried multiple known good logins. The IIS manager allows me to view the file tree in its window, it's only the browser that kicks me out. I even tried going to the virtual directory's Directory Security tab, and under Authentication and Access Control, I tried using the same LIVE domain username for the anonymous access credential. No luck. I'm not trying to run any ASP, ASP.NET, or other dynamic anything out of the virtual directory. I just want IIS to be able to load static images, css, and js files. If anyone has some bright ideas I would be most appreciative!

  Read the article

• MySQL daemon keeps terminating unexpectedly

  - by Yehia A.Salam

  The MySQL daemon on my CentOS server keeps crashing, i got the logs from /var/logs/mysqld but still i am not sure how to fix this: 121114 16:22:56 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended 121114 21:55:11 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql 121114 21:55:11 [Note] Plugin 'FEDERATED' is disabled. 121114 21:55:11 InnoDB: The InnoDB memory heap is disabled 121114 21:55:11 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121114 21:55:11 InnoDB: Compressed tables use zlib 1.2.3 121114 21:55:11 InnoDB: Using Linux native AIO 121114 21:55:11 InnoDB: Initializing buffer pool, size = 128.0M 121114 21:55:11 InnoDB: Completed initialization of buffer pool 121114 21:55:11 InnoDB: highest supported file format is Barracuda. InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 121114 21:55:11 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 121114 21:55:12 InnoDB: Waiting for the background threads to start 121114 21:55:13 InnoDB: 1.1.6 started; log sequence number 77177262 121114 21:55:13 [Note] Event Scheduler: Loaded 0 events 121114 21:55:13 [Note] /usr/libexec/mysqld: ready for connections. Version: '5.5.12' socket: '/var/lib/mysql/mysql.sock' port: 3306 MySQL Community Server (GPL) by Remi 121115 00:19:44 mysqld_safe Number of processes running now: 0 121115 00:19:44 mysqld_safe mysqld restarted 121115 0:19:47 [Note] Plugin 'FEDERATED' is disabled. 121115 0:19:47 InnoDB: The InnoDB memory heap is disabled 121115 0:19:47 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121115 0:19:47 InnoDB: Compressed tables use zlib 1.2.3 121115 0:19:47 InnoDB: Using Linux native AIO 121115 0:19:47 InnoDB: Initializing buffer pool, size = 128.0M InnoDB: mmap(137363456 bytes) failed; errno 12 121115 0:19:47 InnoDB: Completed initialization of buffer pool 121115 0:19:47 InnoDB: Fatal error: cannot allocate memory for the buffer pool 121115 0:19:47 [ERROR] Plugin 'InnoDB' init function returned error. 121115 0:19:47 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 121115 0:19:47 [ERROR] Unknown/unsupported storage engine: InnoDB 121115 0:19:47 [ERROR] Aborting Edit #1 total used free shared buffers cached Mem: 496 370 126 0 24 110 -/+ buffers/cache: 234 261 Swap: 1023 9 1014 Edit #2 Also, largest table in my mysql is 20MB, so my the memory used should be pretty moderate. SELECT CONCAT(table_schema, '.', table_name), CONCAT(ROUND(table_rows / 1000000, 2), 'M') rows, CONCAT(ROUND(data_length / ( 1024 * 1024 * 1024 ), 2), 'G') DATA, CONCAT(ROUND(index_length / ( 1024 * 1024 * 1024 ), 2), 'G') idx, CONCAT(ROUND(( data_length + index_length ) / ( 1024 * 1024 * 1024 ), 2), 'G') total_size, ROUND(index_length / data_length, 2) idxfrac FROM information_schema.TABLES ORDER BY data_length + index_length DESC LIMIT 10;

  Read the article

• What is a good method to solve cabal install problems?

  - by sp3ctum

  I've used the cabal package manager for Haskell programs to install libraries and new projects that I've cloned from some repositories. More often than not, I keep running into problems. Most projects make installing them seem super easy, but in my case that's not always true - sometimes they are very hard to get running. Some are so hard, in fact, that I've lost interest in the project solely because of not being able to install it. So instead of complaining, I'd like to ask what I should do to better this situation. I'd like to use my most recent problem as an example. I'm interested in trying out the Gitit project. It's a promising looking personal wiki that runs on various version control systems. So here's what I've done: Clone from Github run cabal install in the project directory like I'm told on the project install page: mika@eka:~/git/gitit$ ls BLUETRIP-LICENSE CHANGES HCAR-gitit.tex LICENSE Network README.markdown RELANN-0.6.1 Setup.lhs TANGOICONS YUI-LICENSE data expireGititCache.hs gitit.cabal gitit.hs plugins mika@eka:~/git/gitit$ cabal install Resolving dependencies... cabal: cannot configure happstack-server-7.0.7. It requires base64-bytestring ==1.0.* For the dependency on base64-bytestring ==1.0.* there are these packages: base64-bytestring-1.0.0.0. However none of them are available. base64-bytestring-1.0.0.0 was excluded because gitit-0.10 requires base64-bytestring ==0.1.* mika@eka:~/git/gitit$ So now I'm thinking: well, I'll install happstack-server on its own, maybe that will work: mika@eka:~/git/gitit$ cabal install happstack-server Resolving dependencies... Warning: happstack-server.cabal: Ignoring unknown section type: test-suite Configuring happstack-server-7.0.7... cabal: At least the following dependencies are missing: blaze-html ==0.5.*, hslogger >=1.0.2, monad-control ==0.3.*, network >=2.2.3, sendfile >=0.7.1 && <0.8, system-filepath >=0.3.1, text >=0.10 && <0.12, threads >=0.5, transformers-base ==0.4.* cabal: Error: some packages failed to install: happstack-server-7.0.7 failed during the configure step. The exception was: ExitFailure 1 So looks like there are some dependencies missing. But isn't installing these dependencies the whole point of using cabal in the first place? What should I do? File bug reports (to which project?), install the dependencies manually or something else? Bonus points for explaining what causes these kinds of problems.

  Read the article

• Tuning Linux IP routing parameters -- secret_interval and tcp_mem

  - by Jeff Atwood

  We had a little failover problem with one of our HAProxy VMs today. When we dug into it, we found this: Jan 26 07:41:45 haproxy2 kernel: [226818.070059] __ratelimit: 10 callbacks suppressed Jan 26 07:41:45 haproxy2 kernel: [226818.070064] Out of socket memory Jan 26 07:41:47 haproxy2 kernel: [226819.560048] Out of socket memory Jan 26 07:41:49 haproxy2 kernel: [226822.030044] Out of socket memory Which, per this link, apparently has to do with low default settings for net.ipv4.tcp_mem. So we increased them by 4x from their defaults (this is Ubuntu Server, not sure if the Linux flavor matters): current values are: 45984 61312 91968 new values are: 183936 245248 367872 After that, we started seeing a bizarre error message: Jan 26 08:18:49 haproxy1 kernel: [ 2291.579726] Route hash chain too long! Jan 26 08:18:49 haproxy1 kernel: [ 2291.579732] Adjust your secret_interval! Shh.. it's a secret!! This apparently has to do with /proc/sys/net/ipv4/route/secret_interval which defaults to 600 and controls periodic flushing of the route cache The secret_interval instructs the kernel how often to blow away ALL route hash entries regardless of how new/old they are. In our environment this is generally bad. The CPU will be busy rebuilding thousands of entries per second every time the cache is cleared. However we set this to run once a day to keep memory leaks at bay (though we've never had one). While we are happy to reduce this, it seems odd to recommend dropping the entire route cache at regular intervals, rather than simply pushing old values out of the route cache faster. After some investigation, we found /proc/sys/net/ipv4/route/gc_elasticity which seems to be a better option for keeping the route table size in check: gc_elasticity can best be described as the average bucket depth the kernel will accept before it starts expiring route hash entries. This will help maintain the upper limit of active routes. We adjusted elasticity from 8 to 4, in the hopes of the route cache pruning itself more aggressively. The secret_interval does not feel correct to us. But there are a bunch of settings and it's unclear which are really the right way to go here. /proc/sys/net/ipv4/route/gc_elasticity (8) /proc/sys/net/ipv4/route/gc_interval (60) /proc/sys/net/ipv4/route/gc_min_interval (0) /proc/sys/net/ipv4/route/gc_timeout (300) /proc/sys/net/ipv4/route/secret_interval (600) /proc/sys/net/ipv4/route/gc_thresh (?) rhash_entries (kernel parameter, default unknown?) We don't want to make the Linux routing worse, so we're kind of afraid to mess with some of these settings. Can anyone advise which routing parameters are best to tune, for a high traffic HAProxy instance?

  Read the article

• Guests can't access KVM host server by name although nslookup and dig returns correct record

  - by user190196

  So I have a KVM host that also runs an apache server with some yum repos. The VM guests are connected to the default virtual network, which is configured to offer DHCP and forwarding with NAT on virbr0 (192.168.12.1). The guests can successfully access the yum repos on the host by IP address, so for example curl 192.168.122.1/repo1 returns the content without problems. But I'd like to have the guests be able to reach the web server on the host by name rather IP address. I added the desired name record to the host's /etc/hosts file and libvirt's dnsmasq service seems to be serving that correctly to the guests since nslookup and dig successfully resolve the name on the guests: [root@localhost ~]# nslookup repo Server: 192.168.122.1 Address: 192.168.122.1#53 Name: repo Address: 192.168.122.1 [root@localhost ~]# dig repo ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6 <<>> repo ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 55938 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;repo. IN A ;; ANSWER SECTION: repo. 0 IN A 192.168.122.1 ;; Query time: 0 msec ;; SERVER: 192.168.122.1#53(192.168.122.1) ;; WHEN: Tue Sep 17 02:10:46 2013 ;; MSG SIZE rcvd: 38 But curl/ping/etc still fail: [root@localhost ~]# curl repo curl: (6) Couldn't resolve host 'repo' While a request via ip address works: [root@localhost ~]# curl 192.168.122.1 <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 3.2 Final//EN"> <html> <head> <title>Index of /</title> [...] Same with ping: [root@localhost ~]# ping repo ping: unknown host repo [root@localhost ~]# ping 192.168.122.1 PING 192.168.122.1 (192.168.122.1) 56(84) bytes of data. 64 bytes from 192.168.122.1: icmp_seq=1 ttl=64 time=0.110 ms 64 bytes from 192.168.122.1: icmp_seq=2 ttl=64 time=0.146 ms 64 bytes from 192.168.122.1: icmp_seq=3 ttl=64 time=0.191 ms ^C --- 192.168.122.1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2298ms rtt min/avg/max/mdev = 0.110/0.149/0.191/0.033 ms I tried adding repo 192.168.122.1 to the guests' /etc/hosts files but still no dice. Also tried changing guests' /etc/nsswitch.conf with both: hosts: files dns and hosts: dns files I've read the relevant libvirt documentation and I'm not sure where else to learn more about this and be able to move forward with it.

  Read the article

• Squid 2.7.STABLE3-4.1 as a transparent proxy on Ubuntu Server 9.04

  - by LOGIC9

  Can't get this to work at all! I'm trying to get this linux box to act as a transparent proxy and, with the help of DHCP, force everyone on the network to gate into the proxy. I have two ethernet connections, both to the same switch. And I'm trying to get 192.168.1.234 to become the default gateway. The actual WAN connection is to a gateway 192.168.1.1. eth0 is 192.168.1.234 eth1 is 192.168.1.2 Effectively I'm trying to make eth0 a LAN only interface and eth1 a WAN interface. I've oi should set the gateway for eth1 to point to 192.168.1.234 my squid.conf file has the following directives added at the bottom: nly set eth0 to have a gateway address in /etc/network/interfaces I'm not sure whether http_port 3128 transparent acl lan src 192.168.1.0/24 acl lh src 127.0.0.1/255.255.255.0 http_access allow lan http_access allow lh i've added the following routing commands: iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.1.2:3128 iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 I set a computer with TCP settings 192.168.1.234 as the gateway and opened up google.com, but it comes up with a request error. Any ideas why this isn't working? :( Been searching continuously for a solution to no avail. ----------------------------- EDIT ------------------------------- Managed to get it to route properly to the squid, here's the error I get in the browser: ERROR The requested URL could not be retrieved While trying to process the request: GET / HTTP/1.1 Host: www.google.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.1.2) Gecko/20090729 Firefox/3.5.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-gb,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive Cache-Control: max-age=0 The following error was encountered: * Invalid Request Some aspect of the HTTP Request is invalid. Possible problems: * Missing or unknown request method * Missing URL * Missing HTTP Identifier (HTTP/1.0) * Request is too large * Content-Length missing for POST or PUT requests * Illegal character in hostname; underscores are not allowed Your cache administrator is webmaster. Generated Mon, 26 Oct 2009 03:41:15 GMT by mjolnir.lloydharrington.local (squid/2.7.STABLE3)

  Read the article

• ubuntu hardrive repartition without uninstalling ubuntu or windows 7 and losing data of hardrive

  - by user141692

  I have and asus r500v with 750 gb gpt system uefi motherboard core i7 3610qm, nvidia geforce gt, with ubuntu and w7 dual boot, I had problems installing ubuntu because of the grub but I fix it with https://bugs.launchpad.net/ubuntu/+source/grub2/+bug/807801, but I still have the problem of "warning: the partition is misaligned by 3072 bytes. this may result iin very poor performance. Repartitioning is suggested" in every linux partitioin I made and my 750 gb is not being used at the maximun capacity it only uses 698 gb. I want to make partitions so that the warning doesnt show up and I can use the maximum capacity of the HDD, as I did with another dual boot laptop (compaq presario cq40). I have the following partitions: unknown 1.0Mb: partition type: lynux Basic DAta partition, device: /dev/sda2 Usage: --, Partition flags: --, partition label:-- warning: the partition is misaligned by 3072 bytes. this may result in very poor performance. repartitioning is suggested. -system 210 Mb FAt, usage: Filesystem, partition type: EFI system Partition, Partition Flags:--, Label: system, Device: /dev/sda1, partition label: EFI system partition, Capacity 210MB, avilable:--, Mount Point: mounted at /boot/efi -134 Mb NTFS, usage: filesystem, partition type: linux basic data partition, partition flags:.--, device: /dev/sda7, partition label: --, capacity: 134MB,available:--, mount point: not mounted -OS 250 GB NTFS, usage: file system, partititon type: linux basic data partition, partition flags: --, type: NTFS, label: OS, device: /dev/sda3, partition label: basic data partition, capacity: 250 GB, available:-, mount point: not mounted -10GB FAT 32, usage: filesystem, partition type: EFI system partition, partition flags:--, type: FAT 32, label: --, device: /dev/sda4, partition label: --, capacity: 10GB, available:--, mount point: not mounted warning: the partition is misaligned by 3072 bytes. this may result in very poor performance. repartitioning is suggested. -10gb ext 4, usage: file system, partition type: linux basic data partition, partition flags:--, type: EXT4(version1) label:--, device: /dev/sda9, partition label:--, capacity: 10 GB, available:--, mount point at / warning: the partition is misaligned by 1536 bytes. this may result in very poor performance. repartitioning is suggested. -478GB ext4, usage: filesystem, partition type: linux basic data partition, partition flags:--, type: EXT4, label:--, device: /dev/sda5, partition label:--, capacity: 478gb, available:--, mount point: mounted at /home warning: the partition is misaligned by 512 bytes. this may result in very poor performance. repartitioning is suggested. -2.0gb Swap 2.0Gb, usage: swap space, partition type: linux swap partitioin, partition flags:-, device: /dev/sda6, partition label: capacity: 2.0gb warning: the partition is misaligned by 512 bytes. this may result in very poor performance. repartitioning is suggested. and as you can see it is not well organized so please help me to organize the partitions witahout uninstalling the w7, and if possible the grub2

  Read the article

• Why is my router not routing?

  - by dwj

  Starting a week and half ago my router stopped working with my cable modem. I went to sleep with it working and woke up with it not. I swapped in another router and am still having issues; I was gone for 10 days so now I'm back to trying to figure it out. While I was gone I left everything (cable modem, router, and computer) powered off. My setup: Comcast Ambit cable modem (from Comcast) Netgear WGR614 v4 router -- replaced with Linksys WRT54GS v1.1 Windows XP SP3 other computers, all currently unplugged The modem is using the firmware (ver 2.105.2001) provided by Comcast; hardware version 1.3 The Linksys router is using FW ver 4.71.4 (latest for this release of HW), factory defaults I am only using the wired connections; no wireless. I have swapped out all of the cat5 cable. If I plug my computer directly into the cable modem, I can ping by name or number. Everything works perfectly. If I plug my computer into the router and the router into the modem, I cannot access anything outside of my local network. This is the exact setup I've used for the past 5 years; there were no changes in the past year. Now here's the interesting part: I can log into the Linksys router and get status information from it; everything appears good. Using the Diagnostics, I can run ping and traceroute to any site on the internet. These work perfectly. From my computer, I can ping the router and the modem. However, I cannot ping anything on the internet by with name or number. If I plug in another computer, I can ping it successfully. I've included two transcripts below that show these two attempts. Addresses, DNS, gateways, etc. look good. I cannot access the internet through either router. I am at a loss here. Suggestions? Help! Computer to Router to Cable Modem C:\ipconfig /renew Windows IP Configuration No operation can be performed on Bluetooth Network while it has its media disconnected. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected C:\ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : wynton Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hsd1.ca.comcast.net. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. Description . . . . . . . . . . . : Intel(R) 82562V-2 10/100 Network Connection Physical Address. . . . . . . . . : 00-1D-09-9B-45-EB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.100 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 68.87.76.178 68.87.78.130 Lease Obtained. . . . . . . . . . : Monday, March 22, 2010 10:21:55 PM Lease Expires . . . . . . . . . . : Tuesday, March 23, 2010 10:21:55 PM Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : 00-0A-3A-6F-68-41 C:\ping google.com Ping request could not find host google.com. Please check the name and try again . C:\ping 74.125.19.104 Pinging 74.125.19.104 with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 74.125.19.104: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\ Computer to Cable Modem Directly C:\ipconfig /renew Windows IP Configuration No operation can be performed on Bluetooth Network while it has its media disconnected. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. IP Address. . . . . . . . . . . . : 71.204.149.195 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 71.204.148.1 Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected C:\ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : wynton Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hsd1.ca.comcast.net. Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hsd1.ca.comcast.net. Description . . . . . . . . . . . : Intel(R) 82562V-2 10/100 Network Connection Physical Address. . . . . . . . . : 00-1D-09-9B-45-EB Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 71.204.149.195 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 71.204.148.1 DHCP Server . . . . . . . . . . . : 68.87.76.10 DNS Servers . . . . . . . . . . . : 68.87.76.178 68.87.78.130 Lease Obtained. . . . . . . . . . : Monday, March 22, 2010 10:18:50 PM Lease Expires . . . . . . . . . . : Monday, March 22, 2010 11:12:31 PM Ethernet adapter Bluetooth Network: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Bluetooth LAN Access Server Driver Physical Address. . . . . . . . . : 00-0A-3A-6F-68-41 C:\ping google.com Pinging google.com [74.125.19.99] with 32 bytes of data: Reply from 74.125.19.99: bytes=32 time=20ms TTL=55 Reply from 74.125.19.99: bytes=32 time=17ms TTL=55 Reply from 74.125.19.99: bytes=32 time=28ms TTL=55 Reply from 74.125.19.99: bytes=32 time=18ms TTL=55 Ping statistics for 74.125.19.99: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 17ms, Maximum = 28ms, Average = 20ms C:\ping 74.125.19.104 Pinging 74.125.19.104 with 32 bytes of data: Reply from 74.125.19.104: bytes=32 time=18ms TTL=55 Reply from 74.125.19.104: bytes=32 time=18ms TTL=55 Reply from 74.125.19.104: bytes=32 time=17ms TTL=55 Reply from 74.125.19.104: bytes=32 time=16ms TTL=55 Ping statistics for 74.125.19.104: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 16ms, Maximum = 18ms, Average = 17ms C:\

  Read the article

• !! 0xc01a00d !! aka Vista won't boot

  - by Chris

  Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box. One of my users has an HP DV5-1235dx laptop running Windows Vista Professional x64. Last night, our WSUS server pushed out a few updates including "Security Update for Windows Vista for x64-based Systems (KB960859)". When we try to boot the laptop today, a black screen with white text comes up displaying: xxx/169894 (something) Where xxx increments rapidly and something is some dll or registry key. Eventually that stops and the screen displays !! 0xc01a00d !! 35566/169894 (\Registry\Machine\COMPONENTS\DerivedDat...) No other computers that received this update are displaying the same error. So far I've tried running CHKDSK off of HBCD. It repaired a thing or two, but the computer still doesn't boot. I tried repairing the Windows install from the Vista CD, but I get a black screen with white text displaying something along the lines of: 0 No Emulation System Type 00 1 No Emulation System Type 00 Select one of the above Booting in Last Known Good Configuration doesn't work. Booting in Safe Mode freezes at Loading Windows Files [snip] Loaded: \windows\system32\drivers\crcdisk.sys Please wait... My next step is trying to boot Safe Mode with Command Prompt and try to run rstrui.exe. While I do that, does anybody have any guidance? Edit: Booting into Safe Mode with Command Prompt will not work. See Booting in Safe Mode above. Edit 2: I managed to boot from the Vista DVD. I ran the system repair, and now I get a black screen with white text saying: !! 0xc0000034 !! 290/169894 (_0000000000000000.cdf-ms) Edit 3: I ran the system repair again, and it attempted to repair my hard drive. It failed. Problem Signature: Problem Event Name: Startup Repair V2 Problem Signature 01: External Media Problem Signature 02: 6.0.6001.18000.6.0.6001.18000 Problem Signature 03: 4 Problem Signature 04: 196611 Problem Signature 05: CorruptVolume Problem Signature 06: NoBootFailure Problem Signature 07: 0 Problem Signature 08: 0 Problem Signature 09: unknown Problem Signature 10: 1168 OS Version: 6.0.6002.2.2.0.256.1 Locale ID: 1033 Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box.

  Read the article

• Adaptec 5805 after reboot don't starting

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not included. It only works if the computer is shut down and turn off. Late i update firmware "Adaptec RAID 5805 Firmware Build 18948" How to fix the problem? add Log Configuration summary Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priorityHigh Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1 List item

  Read the article

• Issue with Netgear GS108T Managed Switch and Jumbo Frames

  - by Richie086

  I recently purchased a Netgear GS108T managed switch and I am trying to configure jumbo packets between my NAS (Thecus N4100Pro), PC and managed switch. I should mention the fact that I was able to use jumbo frames between my PC and NAS before I purchased the switch without issue. My Desktop has a wired gigabit NIC (Intel 82579V Gigabit) and has the ability to configure jumbo frames (see pic) that are either 9014 bytes or 4088 bytes. I choose 9014 bytes for the jumbo frame size My NAS supports jumbo frames as well, and is configured to use 9014 as the frame size. When I go into my Netgear managed switch and set the frame size to 9014 on the ports I am using for my PC and NAS. See image As soon as I hit apply in the web interface, I loose my connection to the SMB shares on my NAS and I can no longer connect to the web admin interface for my NAS. The really strange thing is I can ping my NAS via the ping command, but when I try to connect to the web interface on port 80 or port 443 the page never loads. I did a scan from my PC to my NAS using nmap and I can see the following ports open PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 111/tcp open rpcbind 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds 631/tcp open ipp 2000/tcp open cisco-sccp 2049/tcp open nfs 3260/tcp open iscsi 49152/tcp open unknown MAC Address: 00:14:FD:15:00:44 (Thecus Technology) Read data files from: C:\Program Files (x86)\Nmap Nmap done: 1 IP address (1 host up) scanned in 211.97 seconds Raw packets sent: 1 (28B) | Rcvd: 1 (28B) Anyone have any idea what is going on here? Why is nmap able to detect the ports are open and listening for http, https and file sharing but I cant connect when all devices have jumbo packets enabled? Stranger still - I did a packet capture using wireshark while the nmap scan was running and filtered so I only saw converstations between my PC and my NAS. Here are the packet details from my scan Only 4 packets over 5k bytes? What is going on here? Do I not need to configure jumbo frame sizes on the switch? I have an internet connection from my pc to the switch to my router - I just cannot connect to my NAS. I just checked on my iPhone and I am able to open my NAS web admin interface without issue on my iPhone! WTF!!!!!! Let me know if you need more details..

  Read the article

• Stop squid caching 302 and 307 with deny_info

  - by 0xception

  TLDR: 302, 307 and Error pages are being cached. Need to force a refresh of the content. Long version: I've setup a very minimal squid instance running on a gateway which shouldn't not cache ANYTHING but needs to be solely used as a domain based web filter. I'm using another application which redirects un-authenticated users to the proxy which then uses the deny_info option redirects any non-whitelisted request to the login page. After the user has authenticated the firewall rule gets placed so they no longer get sent to the proxy. The problem is that when a user hits a website (xkcd.com) they are unauthenticated so they get redirected via the firewall: iptables -A unknown-user -t nat -p tcp --dport 80 -j REDIRECT --to-port 39135 to the proxy at this point squid redirects the user to the login page using a 302 (i've also tried 307, and i've also make sure the headers are set to no-cache and/or no-store for Cache-Control and Pragma). Then when the user logs into the system they get firewall rule which no longer directs them to the squid proxy. But if they go to xkcd.com again they will have the original redirection page cached and will once again get the login page. Any idea how to force these redirects to NOT be cached by the browser? Perhaps this is a problem w/ the browsers and not squid, but not sure how to get around it. Full squid config below. # # Recommended minimum configuration: # acl manager proto cache_object acl localhost src 127.0.0.1/32 ::1 acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1 acl localnet src 192.168.182.0/23 # RFC1918 possible internal network acl localnet src fc00::/7 # RFC 4193 local private network range acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines acl https port 443 acl http port 80 acl CONNECT method CONNECT # # Disable Cache # cache deny all via off negative_ttl 0 seconds refresh_all_ims on #error_default_language en # Allow manager access only from localhost http_access allow manager localhost http_access deny manager # Deny access to anything other then http http_access deny !http # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !https visible_hostname gate.ovatn.net # Disable memory pooling memory_pools off # Never use neigh cache objects for cgi-bin scripts hierarchy_stoplist cgi-bin ? # # URL rewrite Test Settings # #acl whitelist dstdomain "/etc/squid/domains-pre.lst" #url_rewrite_program /usr/lib/squid/redirector #url_rewrite_access allow !whitelist #url_rewrite_children 5 startup=0 idle=1 concurrency=0 #http_access allow all # # Deny Info Error Test # acl whitelist dstdomain "/etc/squid/domains-pre.lst" deny_info http://login.domain.com/ whitelist #deny_info ERR_ACCESS_DENIED whitelist http_access deny !whitelist http_access allow whitelist http_port 39135 transparent ## Debug Values access_log /var/log/squid/access-pre.log cache_log /var/log/squid/cache-pre.log # Production Values #access_log /dev/null #cache_log /dev/null # Set PID file pid_filename /var/run/gatekeeper-pre.pid SOLUTION: I believe I might have found a solution to this. After days and days trying to figure it out, only through a random stumble I found client_persistent_connections off server_persistent_connections off This did the trick. So it wasn't so much cache as it was a single persistent connection messing things up. W000T!

  Read the article

• Uninstall php and nginx or fix setup

  - by jreed121

  First off, I'm a huge linux noob - sorry... I'm trying to setup nginx with php-fpm on debian and I'm pretty sure that I've completely screwed it up. nginx seems to be running fine because I can it it from a web browser and it load the stock "Welcome to nginx!" page. I'm not so sure about php-fpm though. When I try something like # restart php-fpm I get: bash: restart: command not found First off php-fpm some how got installed as php5-fpm when I do root@server:/etc/init.d# ls, which seems to contradict every tutorial and help doc I've read (supposed to be 'php-fpm'). I can restart it with this: service php5-fpm restart And just enter the package name 'php5-fpm' I get this: root@server:~# php5-fpm [17-Nov-2012 23:15:36] NOTICE: PHP message: PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20100525/suhosin.so' - /usr/lib/php5/20100525/suhosin.so: cannot open shared object file: No such file or directory in Unknown on line 0 [17-Nov-2012 23:15:36] ERROR: An another FPM instance seems to already listen on /var/run/php5-fpm.sock [17-Nov-2012 23:15:36] ERROR: FPM initialization failed The root for nginx is /usr/share/nginx/html, when I try to navigate to a .php file in there with my web browser, it tries to download the file instead of interpret it. I would like this folder to be in my user's home directory ie: /home/administrator/www or /home/nginx/www. I know in order to do this I need to modify nginx.conf, but I find that configuration file difficult to understand. I suppose the fact that my .php scripts aren't being handled is my bigger problem anyways. When I try to see what running on port 9000 (php-fpm default port) with lsof -i :9000 it returns nothing - I guess indicating that it isn't listening. then I head over to vim /etc/php5/fpm/php-fpm.conf and there is no where to designate a port number. So should I just uninstall everything and start from scratch? If so, how do I clean it all up? Any suggestions for a tutorial once I'm ready to try again? Should I attempt to troubleshoot this mess? If so where should I start? Sorry guys, I'm feeling pretty stupid and lost right now. I'm not sure what my next steps are in trying to resolve this issue are. I realize that this is a horrible question for this type of Q&A site, but I'd really appreciate any guidance.

  Read the article

• How to solve/disable spam sending with my postfix server on linux

  - by Dukla

  I am quite new in setting up e-mail server on linux - I barely set up the whole think to get it working and connected it with my domain and php script which uses PHPMailer 5.2.1. In my setting I am using smtp server from my web provider (domain) and all e-mail which are not defined (trash) are sent on one simple address like I have address [email protected]. So when somebody will send email to [email protected] it will be forwarded again to [email protected] even in case of failure. I am receiving emails like: Hi. This is the qmail-send program at comercio.interone.com.br. I'm afraid I wasn't able to deliver your message to the following addresses. This is a permanent error; I've given up. Sorry it didn't work out. <[email protected]>: Sorry, no mailbox here by that name. (#5.1.1) --- Below this line is a copy of the message. Return-Path: <[email protected]> Received: (qmail 49156 invoked from network); 25 Jun 2012 07:34:57 -0300 Received: from unknown (HELO S0106602ad08df877.no.shawcable.net) (70.66.34.103) by hosting.interone.com.br with SMTP; 25 Jun 2012 07:34:57 -0300 Message-Id: <20120625034039.B45C12DCC3B13A22F261@GANDERTO-015445> From: Ezra Whitehead <[email protected]> To: toa <[email protected]> Reply-To: Jamey Mcconnell <[email protected]> Subject: Welcome toa Mime-Version: 1.0 Content-Type: text/plain; charset=utf-8 Content-Transfer-Encoding: 7bit Visit our shop http://44090.medicneed.ru/ 113B726C73560AA41A68163AA474D5F1476 0225770686522678 As you can see there is line From: Ezra Whitehead <[email protected]> I am sure I did not send this email from my domain.com with some Davis8FB name and some russian page. This is just one of many and only NOT-delivered e-mails - there can be much more which has been sent successfully! What do I have wrong in my settings? How can I make it right? What should I do to prevent these messages to send? Where should I look? Thank you all.

  Read the article

• Lenovo Ideapad Y480 can't reinstall windows?

  - by elegantonyx

  Alright, so here's the deal... For a while, I wanted to mess with Linux. I don't know why, but I wanted to. So, what I did was use WUBI and install Ubuntu. Because of some unknown reason (Intel Rapid Start? Half the drivers being on a Lenovo-installed SSD [separate from the main hard drive]?) it wouldn't dual boot. So, I decided to use Linux Mint instead, and install it in a partition. Since Windows 7 Home Premium won't make partitions any more if you have a certain number already, I just shrank my system drive and left empty space for the installer to claim. When I installed Mint, it worked, but left my Windows 7 installation unable to boot and eventually it corrupted. I tried to use a system repair disc I burned earlier but it didn't find the Windows installation, so I assume the partition corrupted. I used this link:http://www.pcworld.com/article/248995/how_to_install_windows_7_without_the_disc.html to try and reinstall Windows. What happened was that originally it said that the partition I was trying to reinstall from had been locked down by the OEM (Lenovo). So, I went into GParted, wiped EVERYTHING, and selected 'Construct new Boot record' or whatever that function is, and now the error is: "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information." Does anyone know how to see the log files? Can anyone help? This system is a month old but the warranty only covers hardware failures, and I would need to pay around USD$60 for them to fix it. Please help. Any ideas? this is my main machine... Extra information: I have at my disposal: System Repair Disc (Burned myself) Windows 7 Home Premium 64 bit SP1 installation disk (burned from the pcworld links) Gparted Live CD Linux Mint 13 live cd A system backup (from the morning before this catastrophe) made using the Windows Backup and Restore. I put it on an external drive...that should be safe for now.

  Read the article

• How to remove iso 9660 from USB?

  - by a_m0d

  I have somehow managed to write an iso 9660 image onto my USB drive, which makes all my computer think that the device is actually a CD. I have tried various methods of removing this partition, but nothing seems to work. I have tried fdisk, which says $ fdisk -l /dev/sdb Cannot open /dev/sdb parted crashes when I try to use it on this device. I have even tried $ dd if=/dev/zero of=/dev/sdb but it just hangs with no output (either on screen or on disk). However, when I plug the USB in, it does mount, and I can view (but not edit) the files on it. edit: now the result is $ dd if=/dev/zero of=/dev/sdb dd: opening `/dev/sdb': Read-only file system I have also tried re-formatting it on Windows, but it gets to the end of the format process and then says "Couldn't format the drive". How can I remove this partition and get my whole USB drive back to normal again? EDIT 1: Trying a simple mkfs doesn't work: $ sudo mkfs -t vfat /dev/sdb mkfs.vfat 3.0.0 (28 Sep 2008) mkfs.vfat: Will not try to make filesystem on full-disk device '/dev/sdb' (use -I if wanted) I can't do mkfs on /dev/sdb1 because there is no such partition, as shown:$ ls /dev | grep sdb sdb EDIT 2: This is the information posted by dmesg when I plug the device in:$ dmesg . . (snip) . usb 2-1: New USB device found, idVendor=058f, idProduct=6387 usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1: Product: Mass Storage usb 2-1: Manufacturer: Generic usb 2-1: SerialNumber: G0905000000000010885 usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access FLASH Drive AU_USB20 8.07 PQ: 0 ANSI: 2 sd 6:0:0:0: [sdb] 4069376 512-byte hardware sectors (2084 MB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sd 6:0:0:0: [sdb] 4069376 512-byte hardware sectors (2084 MB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sdb: unknown partition table sd 6:0:0:0: [sdb] Attached SCSI removable disk sd 6:0:0:0: Attached scsi generic sg2 type 0 ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A SELinux: initialized (dev sdb, type iso9660), uses genfs_contexts CE: hpet increasing min_delta_ns to 15000 nsec This shows that the device is formatted as ISO 9660 and that it is /dev/sdb. EDIT 3: This is the message that I find at the bottom of dmesg after running cfdisk and writing a new partition table to the disk:SELinux: initialized (dev sdb, type iso9660), uses genfs_contexts sd 17:0:0:0: [sdb] Device not ready: Sense Key : Not Ready [current] sd 17:0:0:0: [sdb] Device not ready: < ASC=0xff ASCQ=0xffASC=0xff < ASCQ=0xff end_request: I/O error, dev sdb, sector 0 Buffer I/O error on device sdb, logical block 0 lost page write due to I/O error on sdb

  Read the article

• Ubuntu Newbie Needs Assistance!!

  - by Steve Greene

  New Ubuntu User Needs Help!- version 9.10 does not communicate with laptop Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, even when sitting directly under the wireless router at the local library (literally), which puts out a wickedly-fast signal that my Windows Vista OS auto-detects and immediately connects to. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all, even though I am only a few feet from the router. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I desparately wish to convert to Ubuntu. I used Mac for ten years, and then Windows for ten years. Now, after 20 years, I want to live out my days as an open-source Ubuntu fanatic. I am ready to give the old status quo the boot! I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch so that I can move on in total Ubuntu bliss? My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System. I am running Windows Vista Home Basic, Service Pack 2. My current email is [email protected] if you have a workable solution that does not require programmer status to implement. Surely this must be a simple fix that I simply am overlooking, but being the new guy on the block, I have yet to be enlightened. Thanks for your help in coming up to speed!! Steve Wanna' be Ubuntu Fanatic "If you're not living on the edge, you're taking up too much space."

  Read the article

• SSH: Connection Reset by Peer

  - by hopeless

  I have a Solaris 10 server on another network. I can ping it and telnet to it, but ssh doesn't connect. PuTTY log contains nothing of interest (they both negotiate to ssh v2) and then I get "Event Log: Network error: Software caused connection abort". ssh is defintely running: svcs -a | grep ssh online 12:12:04 svc:/network/ssh:default Here's an extract from the server's /var/adm/messages (anonymised) Jun 8 19:51:05 ******* sshd[26391]: [ID 800047 auth.crit] fatal: Read from socket failed: Connection reset by peer However, if I telnet to the box, I can login to ssh locally. I can also ssh to other (non-Solaris) machines on that network fine so I don't believe that it's a network issue (though, since I'm a few hundred miles away, I can't be sure). The server's firewall is disabled, so that shouldn't be a problem root@******** # svcs -a | grep -i ipf disabled Apr_27 svc:/network/ipfilter:default Any ideas what I should start checking? Update: Based on the feedback below, I've run sshd in debug mode. Here's the client output: $ ssh -vvv root@machine -p 32222 OpenSSH_5.0p1, OpenSSL 0.9.8h 28 May 2008 debug2: ssh_connect: needpriv 0 debug1: Connecting to machine [X.X.X.X] port 32222. debug1: Connection established. debug1: identity file /home/lawrencj/.ssh/identity type -1 debug1: identity file /home/lawrencj/.ssh/id_rsa type -1 debug1: identity file /home/lawrencj/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version Sun_SSH_1.1 debug1: no match: Sun_SSH_1.1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.0 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent Read from socket failed: Connection reset by peer And here's the server output: root@machine # /usr/lib/ssh/sshd -d -p 32222 debug1: sshd version Sun_SSH_1.1 debug1: read PEM private key done: type RSA debug1: private host key: #0 type 1 RSA debug1: read PEM private key done: type DSA debug1: private host key: #1 type 2 DSA debug1: Bind to port 32222 on ::. Server listening on :: port 32222. debug1: Bind to port 32222 on 0.0.0.0. Server listening on 0.0.0.0 port 32222. debug1: Server will not fork when running in debugging mode. Connection from 1.2.3.4 port 2652 debug1: Client protocol version 2.0; client software version OpenSSH_5.0 debug1: match: OpenSSH_5.0 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-Sun_SSH_1.1 debug1: list_hostkey_types: ssh-rsa,ssh-dss debug1: Failed to acquire GSS-API credentials for any mechanisms (No credentials were supplied, or the credentials were unavailable or inaccessible Unknown code 0 ) debug1: SSH2_MSG_KEXINIT sent Read from socket failed: Connection reset by peer debug1: Calling cleanup 0x4584c(0x0) This line seems a likely candidate: debug1: Failed to acquire GSS-API credentials for any mechanisms (No credentials were supplied, or the credentials were unavailable or inaccessible

  Read the article

• sendmail on ubuntu (9.10) machine "stopped" sending mail

  - by Doron

  I'm developing on my ubuntu 9.10 machine for the web (php). I'm using it sendmail for sending mails, and while developing on my local machine, I send local mails (to my user 'doron'). Up until a few days ago, I was able to send mails both from php's mail() function, and from the command line using the mail command. I'm using sendmail with mailutils. Since the last few days, it seems like it stopped working. When I try to send mail from the command line, I get the following in my syslog (and mail.info, and mail.log): Mar 3 13:27:58 doron-desktop sendmail[4693]: o23BRwlA004693: from=doron, size=84, class=0, nrcpts=1, msgid=<201003031127.o23BRwlA004693@doron-desktop.>, relay=doron@localhost Mar 3 13:27:58 doron-desktop sm-mta[4694]: o23BRwtQ004694: ruleset=check_rcpt, arg1=<doron@doron-desktop>, relay=localhost [127.0.0.1], reject=553 5.1.8 <doron@doron-desktop>... Domain of sender address doron@doron-desktop does not exist Mar 3 13:27:58 doron-desktop sendmail[4693]: o23BRwlA004693: to=<doron@doron-desktop>, ctladdr=doron (1000/1000), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30084, relay=[127.0.0.1] [127.0.0.1], dsn=5.1.8, stat=User unknown Mar 3 13:27:58 doron-desktop sm-mta[4694]: o23BRwtQ004694: from=<doron@doron-desktop>, size=84, class=0, nrcpts=0, proto=ESMTP, daemon=MTA-v4, relay=localhost [127.0.0.1] Trying to telnet locally to port 25 results in the following (same output for doron@doron-desktop): doron@doron-desktop:/var/mail$ telnet localhost 25 Trying ::1... Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 doron-desktop. ESMTP Sendmail 8.14.3/8.14.3/Debian-9ubuntu1; Wed, 3 Mar 2010 13:26:06 +0200; (No UCE/UBE) logging access from: localhost(OK)-localhost [127.0.0.1] helo localhost 250 doron-desktop. Hello localhost [127.0.0.1], pleased to meet you mail from: doron@localhost 250 2.1.0 doron@localhost... Sender ok rcpt to: root@localhost 553 5.1.8 root@localhost... Domain of sender address doron@doron-desktop does not exist However - if I do the same, but use [email protected] in the mail from field, I get: 250 2.1.5 root... Recipient ok My /etc/hosts file: 127.0.0.1 localhost 127.0.1.1 doron-desktop doron-desktop. (If I don't have the "doron-desktop." (with the ending dot), the mail command takes a lot of time (around 30 seconds) until it responds, but the results are the same.)

  Read the article

• Network Bridging for WiFi-to-Ethernet in linux

  - by shakaran

  It is possible Network Bridging for WiFi-to-Ethernet in linux instead of Ethernet-to-Ethernet? I have a CentOS 6.3 machine. I am using KVM and I want perform a brigde for virtualize more machines. This machine is connected only via wireless connection and it doesn't have a ethernet connection. So, I did a bridge over the WiFi interface like: # cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE="br0" NM_CONTROLLED="yes" ONBOOT=yes TYPE=Bridge BOOTPROTO=none IPADDR=192.168.1.50 PREFIX=24 GATEWAY=192.168.1.1 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System br0" Then I edit my wireless conection like: # cat /etc/sysconfig/network-scripts/ifcfg-mywireless ESSID="mywireless" MODE=Managed KEY_MGMT=WPA-PSK WPA_ALLOW_WPA2=yes CIPHER_PAIRWISE=CCMP CIPHER_GROUP=CCMP TYPE=Wireless #BOOTPROTO=none #IPADDR=192.168.1.50 #PREFIX=24 #GATEWAY=192.168.1.1 #DNS1=8.8.8.8 #DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="Auto mywireless" UUID=874***** ONBOOT=yes LAST_CONNECT=1355923469 BRIDGE=br0 After, I restart the network: # /etc/init.d/network restart Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface Auto_mywireless: Error: Unknown connection: 874***** [FAILED] Bringing up interface br0: [ OK ] But as you can see, it show a error. My ifconfig output shows now: # ifconfig br0 Link encap:Ethernet HWaddr 6E:20:AD:CE:D8:AB inet addr:192.168.1.50 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6c20:adff:fece:d8ab/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:6393 (6.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:432 errors:0 dropped:0 overruns:0 frame:0 TX packets:432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:62433 (60.9 KiB) TX bytes:62433 (60.9 KiB) ra0 Link encap:Ethernet HWaddr 00:22:F7:2B:87:E5 inet addr:192.168.1.42 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:f7ff:fe2b:87e5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:46 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:487894880 (465.2 MiB) TX bytes:148136473 (141.2 MiB) virbr0 Link encap:Ethernet HWaddr 52:54:00:5B:30:9A inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:70 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:5838 (5.7 KiB) But this doesn't give internet connection and I loss access to 192.168.1.50. So, it is possible setup this networking bridge WiFi-to-Ethernet?

  Read the article

• Why can't I use SSL certs imported via Server Admin in a custom Apache install?

  - by morgant

  I've got a couple of Mac OS X 10.6.8 Server web servers that run a custom AMP255 (Apache 2.x, MySQL 5.x, and PHP 5.x) stack installed using MacPorts. We've got a lot of Mac OS X Server servers and generally install SSL certs via Server Admin and they "just work" in the built-in services, however, these web servers have always had SSL certs installed in a non-standard location and used only for Apache. Long story short, we're trying to standardize this part of our administration and install certs via Server Admin, but have run into the following issue: when the certs are installed via Server Admin and referenced in our Apache conf files, Apache then prompts for a password upon trying to start. It does not seem to be any password we know, certainly not the admin or keychain passwords! We've added the _www user to the certusers (mainly just to ensure they have the proper access to the private key in /etc/certificates/). So, with the custom installed certs we have the following files (basically just pasted in from the company we purchase our certs from): -rw-r--r-- 1 root admin 1395 Apr 10 11:22 *.domain.tld.ca -rw-r--r-- 1 root admin 1656 Apr 10 11:21 *.domain.tld.cert -rw-r--r-- 1 root admin 1680 Apr 10 11:22 *.domain.tld.key And the following in the VirtualHost in /opt/local/apache2/conf/extra/httpd-ssl.conf: SSLCertificateFile /path/to/certs/*.domain.tld.cert SSLCertificateKeyFile /path/to/certs/*.domain.tld.key SSLCACertificateFile /path/to/certs/*.domain.tld.ca This setup functions normally. If we use the certs installed via Server Admin, which both Server Admin & Keychain Assistant show as valid, they're installed in /etc/certificates/ as follows: -rw-r--r-- 1 root wheel 1655 Apr 9 13:44 *.domain.tld.SOMELONGHASH.cert.pem -rw-r--r-- 1 root wheel 4266 Apr 9 13:44 *.domain.tld.SOMELONGHASH.chain.pem -rw-r----- 1 root certusers 3406 Apr 9 13:44 *.domain.tld.SOMELONGHASH.concat.pem -rw-r----- 1 root certusers 1751 Apr 9 13:44 *.domain.tld.SOMELONGHASH.key.pem And if we replace the aforementioned lines in our httpd-ssl.conf with the following: SSLCertificateFile /etc/certificates/*.domain.tld.SOMELONGHASH.cert.pem SSLCertificateKeyFile /etc/certificates/*.domain.tld.SOMELONGHASH.key.pem SSLCertificateChainFile /etc/certificates/*.domain.tld.SOMELONGHASH.chain.pem This prompts for the unknown password. I have also tried httpd-ssl.conf configured as follows: SSLCertificateFile /etc/certificates/*.domain.tld.SOMELONGHASH.cert.pem SSLCertificateKeyFile /etc/certificates/*.domain.tld.SOMELONGHASH.key.pem SSLCertificateChainFile /etc/certificates/*.domain.tld.SOMELONGHASH.concat.pem And as: SSLCertificateFile /etc/certificates/*.domain.tld.SOMELONGHASH.cert.pem SSLCertificateKeyFile /etc/certificates/*.domain.tld.SOMELONGHASH.key.pem SSLCACertificateFile /etc/certificates/*.domain.tld.SOMELONGHASH.chain.pem We've verified that the certificate is configured to allow all applications access it (in Keychain Assistant). A diff of the /etc/certificates/*.domain.tld.SOMELONGHASH.key.pem & *.domain.tld.key files shows the former is encrypted and the latter is not, so we're assuming that Server Admin/Keychain Assistant is encrypting them for some reason. I know I can create an unencrypted key file as follows: sudo openssl rsa -in /etc/certificates/*.domain.tld.SOMELONGHASH.key.pem -out /etc/certificates/*.domain.tld.SOMELONGHASH.key.no_password.pem But, I can't do that without entering the password. I thought maybe I could export an unencrypted copy of the key from Keychain Admin, but I'm not seeing such an option (not to mention that the .pem options are greyed out in all export options). Any assistance would be greatly appreciated.

  Read the article

< Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >