Search Results

Search found 4244 results on 170 pages for 'mark milford'.

Page 139/170 | < Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >

• solaris zpool SSD cache device "faulted"

  - by John-ZFS

  I am trying to get over these SATA SSD errors - smartctl command failed to read the SATA SSD - SATA is not supported what could be the reason for errors? does this mean that SSD has reached EOL & needs to be replacement? errors: No known data errors pool: zpool1216 state: DEGRADED status: One or more devices are faulted in response to persistent errors. Sufficient replicas exist for the pool to continue functioning in a degraded state. action: Replace the faulted device, or use 'zpool clear' to mark the device repaired. scan: scrub repaired 0 in 0h24m with 0 errors on Fri May 18 14:31:08 2012 config: NAME STATE READ WRITE CKSUM zpool1216 DEGRADED 0 0 0 raidz1-0 ONLINE 0 0 0 c11t10d0 ONLINE 0 0 0 c11t11d0 ONLINE 0 0 0 c11t12d0 ONLINE 0 0 0 c11t13d0 ONLINE 0 0 0 c11t14d0 ONLINE 0 0 0 c11t15d0 ONLINE 0 0 0 c11t16d0 ONLINE 0 0 0 c11t1d0 ONLINE 0 0 0 c11t2d0 ONLINE 0 0 0 c11t3d0 ONLINE 0 0 0 c11t4d0 ONLINE 0 0 0 c11t5d0 ONLINE 0 0 0 c11t6d0 ONLINE 0 0 0 c11t7d0 ONLINE 0 0 0 c11t8d0 ONLINE 0 0 0 c11t9d0 ONLINE 0 0 0 logs c9d0 FAULTED 0 0 0 too many errors cache c10d0 FAULTED 0 17 0 too many errors

  Read the article

• Can't view other computers on Network

  - by Darkart

  Systems: My Machine: Windows 7 Ultimate connected through ethernet into router Her Machine--Other Machine: Windows 7 Ultimate connected through wireless Router:F5D8236-4 N Wireless Router Version 1 Firmware: 2.01.03 (Apr 28 2009) ISP: Comcast Problem: I can not view the "Other Machine" on the network at all. I opened command prompt and ran net view and saw the pc name. I tried pinging the pc and it times out. Went inside the router and tried viewing the computer on the DHCP list and it can not be seen. I restored the router back to default settings and firmware and completely reset the modem and router, and created home group. I went to the other machine to configure home group settings and made sure that both PC's had identical settings. She was able to see my machine but I could not see hers. I restarted both machines and now we cant see each other at all. Also her PC ("Other Machine") had exclamation mark in the wireless icon but was connected just fine. There is no firewalls on currently or anti-virus enabled, and still can not see each other. Right now I am checking for updated drivers for the wireless card, but my question is could it be the router or something hardware related? I have went through all the settings in the Home group and visited most FAQ's and still no luck. Also as it stands I can not view her machine inside the router DHCP Client List :(

  Read the article

• Replace text with spaces in MySQL

  - by javipas

  I'm trying to do a global replace of search in my database, which has a lot of articles with a double carriage return because of this code: <p> </p> I'd like to replace this in my WordPress blog so instead of that appears... nothing, and so I can delete the CR. I've tried this on my database UPDATE wp_posts set post_content = replace (post_content,'<p> </p>',''); but didn't work. Why? Do I have to add special thinks to consider the space between the <p>and the</p>? Mmm. Good points, both Jon Angliss and Wim. Jon, as you could have guessed, the database shows no entries with that text string. So there's something going on inside the post_content field. Wim, the famous   was replaced previously, but there are still hundreds of posts that for some reason have something different between the p and the /p tags. I've done a search of one of the posts with this error: mysql> select * from wp_posts where post_title like '%3DVisionLive%'; And looking in the wp_content field, this is a little piece of the post: Phil Eisler, responsable de la divisi?n 3D Vision.?</p> <p>?</p> <p>Este portal ser? por tanto No spanish tilde (accent) shown on the terminal, and instead of an space there's a quotation mark between the p and the /p tags. I've tried to replace <p>?</p>, but again, no results. There's some character (or several) there, but I don't know how to discover that. Maybe it's the character set of my terminal, but I've accessed the database from phpmyadmin and in that case there's a space character between the p and the /p. Weird.

  Read the article

• Cisco ASA: Routing packets based on where the connections started from

  - by DrStalker

  We have a Cisco ASA 5505 (version 8.2(2)) with three interfaces: outside: IP address 11.11.11.11, this is the default route inside: IP address 10.1.1.1, this is the local subnet newlink: 22.22.22.22, this is a new internet connection. We need to move VPN users from the 11.11.11.11 address to the 22.22.22.22 address, and we're using SSH on the ASA as to test and sort out the routing. The problem we have is this: If we define a particular IP as being on a static route out the newlink interface then it can SSH to 22.22.22.22 fine. If we do not define a static route then the traffic hits the ASA, but the return traffic does not come back over newlink; presumably it gets sent over the outside interfcae as that is the default route. We can't define a static route for each remote endpoint because there are dialup VPN users, who obviously change IP a lot What we need to do is configure the ASA so if a connection comes in on the newlink interface then the outgoing packets for that go over the newlink interface, not the default route. With iptables this should be do-able by marking the connection and doing mark-routing, but what is the equivalent for a Cisco ASA?

  Read the article

• Juniper router dropping pings to external interface

  - by Alexander Garden

  My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

  Read the article

• Red Hat 5.3 on HP Proliant DL380 G5 and failed drive on RAID controller

  - by thinkdreams

  I have a development ERP server here in my office that I assist with support on, and originally the DBA requested a single drive setup for some of the drives on the server. Thus the hardware RAID controller (an HP embedded controller) looks like: c0d0 (2 drive) RAID-1 c0d1 (2 drive) RAID-1 c0d2 (1 drive) No RAID <-- Failed c0d3 (1 drive) No RAID c0d4 (1 drive) No RAID c0d5 (1 drive) No RAID c0d2 has failed. I replaced the drive immediately with a spare using the hot-swap, but the c0d2 continues to mark itself as failed, even when I umount the partition. I'm loathe to reboot the server since I'm concerned about the server coming back up in rescue mode but I'm afraid that's the only way to get the system to re-read the drive. I assumed there was some sort of auto-detection routine for this, but I haven't been able to figure out the proper procedure. I have installed the HP ACU CLI utilties, so I can see the hardware RAID setup. I'd really like to find out what the proper procedure should have been, where I went wrong, and how to correct it now. Obviously this goes without saying I should NOT have listened to the DBA and set the drives up as RAID-1 throughout as was my first instinct. He wasn't worried about data loss, but it sure would have been easier to replace the failed drive. :)

  Read the article

• Why does `rpm` show 3 httpd packages, and which one provides the real httpd?

  - by Stefan Lasiewski

  I ran yum update on my CentOS5 webserver a few days ago. Today I just noticed that I have 3 httpd-* rpms! How can I end up with three RPMs for httpd (My other servers only have one httpd rpm). I want to make sure that my server has a patched, updated version of /usr/sbin/httpd. How can I tell which one of these packages provides the httpd binary at /usr/sbin/httpd? [root@node1 ~]# rpm -q httpd httpd-2.2.3-76.el5.centos httpd-2.2.3-78.el5.centos httpd-2.2.3-83.el5.centos [root@node1 ~]# /usr/sbin/httpd -V |grep version Server version: Apache/2.2.3 [root@node1 ~]# rpm -q httpd-2.2.3-76.el5.centos --list |grep -w /usr/sbin/httpd /usr/sbin/httpd /usr/sbin/httpd.event /usr/sbin/httpd.worker [root@node1 ~]# rpm -q httpd-2.2.3-78.el5.centos --list |grep -w /usr/sbin/httpd /usr/sbin/httpd /usr/sbin/httpd.event /usr/sbin/httpd.worker [root@node1 ~]# rpm -q httpd-2.2.3-83.el5.centos --list |grep -w /usr/sbin/httpd /usr/sbin/httpd /usr/sbin/httpd.event /usr/sbin/httpd.worker [root@node1 ~]# root@node1 ~]# rpm -q --provides httpd |grep -w httpd config(httpd) = 2.2.3-76.el5.centos httpd-mmn = 20051115 httpd = 2.2.3-76.el5.centos config(httpd) = 2.2.3-78.el5.centos httpd-mmn = 20051115 httpd = 2.2.3-78.el5.centos config(httpd) = 2.2.3-83.el5.centos httpd-mmn = 20051115 httpd = 2.2.3-83.el5.centos Update: Answering Mark Wagner's questions: [root@node1 ~]# rpm -q -f /usr/sbin/httpd httpd-2.2.3-76.el5.centos httpd-2.2.3-78.el5.centos httpd-2.2.3-83.el5.centos [root@node1 ~]# rpm -V httpd-2.2.3-83.el5.centos S.5..... c /etc/logrotate.d/httpd S.5..... c /etc/rc.d/init.d/httpd ....L... /var/www

  Read the article

• attach / detach mssql 2008 sql server manager [SOLVED]

  - by Tillebeck

  An external consult wrote a guide on how to copy a database. Step two was detach the database using Sql Server Manager. After the detach the database was not visible in the SQL Server Manager... Not much to do but write a mail to the service provider asking to have the database attached again. The service porviders answer: Not posisble to attach again since the SQL Server security has been violated". Rolling back to last backup is not the option I want to use. Can any one give feedback if this seems logic and reasonable to assume that a detached database in a SQL Server 2008 accessed through SQL Server Manager cannot be reattached. It was done by rightclicking the database and choosing detach. -- update -- Based on the comments below I update the question with the server setup. There are two dedicated servers: srv1: Web server with remote desktop and an Sql Server Manager srv2: Sql server that can be accessed through the Sql Server Manager on the web server -- update2 -- After a restart of the server the DBA could suddenly do the attachment of the database. And I guess that after the restart it was a simple task. So all of your answer were rigth! It seems that I can only mark one as a correct answer so I marked the first answer correct. But all are correct answer. Thanks a lot. Without posting the link to this thread then we might had so suffer while watching our database beeing restored by a backup :-) Thanks a lot. BR. Anders

  Read the article

• DHCP forwarding behind access list on a Cisco Catalyst

  - by Ásgeir Bjarnason

  I'm having some trouble with forwarding DHCP from a subnet behind an access list on a Cisco Catalyst 4500 switch. I'm hoping somebody can see the mistake I'm making. The subnet is defined like this: (first three octets of IP addresses and vrf name anonymized) interface Vlan40 ip vrf forwarding vrf_name ip address 10.10.10.126 255.255.255.0 secondary ip address 10.10.10.254 255.255.255.0 ip access-group 100 out ip helper-address 10.10.20.36 no ip redirects I tried turning on a VMWare machine on this subnet that was configured to use DHCP, but I never got a DHCP response and the DHCP server didn't receive a request. I tried putting the following in the access-list: access-list 100 permit udp host 10.10.10.254 host 10.10.20.36 eq bootps access-list 100 permit udp host 10.10.10.254 host 10.10.20.36 eq bootpc access-list 100 permit udp host 10.10.20.36 host 10.10.10.254 eq bootps access-list 100 permit udp host 10.10.20.36 host 10.10.10.254 eq bootpc That didn't help. Can anybody see what the problem is? I know that the DHCP server works; our whole network is running off of this DHCP server I also know that the subnet works because we have active servers running on the network The DHCP scope is already defined on the DHCP server The subnet is correctly defined on the VMWare server (already servers running on the subnet on VMWare) Edit 2012-10-19: This is solved! The subnet had formerly been defined as a /25 network, but was then expanded into a /24 network. When the DHCP scope was altered after this change it was done incorrectly; the gateway was moved to .254, the leasable IP range was in the lower half of the /24 subnet but we forgot to change the CIDR prefix from /25 into /24. This happened some 2 years ago, and we didn't need to use DHCP on this server network again until this week. Thank you MDMarra and Jason Seemann for looking at the question and trying to troubleshoot. Now I'm wondering if I should mark Jason's answer as the accepted answer (I am new to the Stack Exchange network, so I don't know the etiquette of what to do if I misstated the question like in this case).

  Read the article

• Idle state detection for server

  - by odinmillion

  Windows OS has a service that detects idle state. Details: Task Idle Conditions The computer is considered idle if all the processors and all the disks were idle for more than 90% of the past 15 minutes and if there is no keyboard or mouse input during this period of time. When the Task Scheduler service detects that the computer is idle, the service only waits for user input to mark the end of the idle state. It is very useful for usual PCs that have keyboard amd mouse. We can use standard task scheduler to start some process like defrag when PC in idle state and stop when PC isn't in idle state. But what should we use when we using a standalone server without keyboard and mouse? Server sometimes receives commands by TCP/IP and starts CPU and HDD activity. But sometimes CPU and HDD activity at zero level. I would like to use this periods of time to start defrag or another process. But this started at "idle" state processes should be terminated when another commands will appear. So, standard idle state conditions cant help me because we have not got user input to stop idle state. I need more customizable idle state detector. Automatically started processes shouldn't influence to idle state, but PC should go away from idle state when another process will apperar. What should I use? Maybe exists some advansed task scheduler? Or I should write some useful utility on C#? I hope that it is a standard task and all useful utilities already compiled :)

  Read the article

• VPN on OSX disconnects after precisely 2 minutes and 30 seconds on specific network

  - by Tyilo

  When connecting to my own VPN server on a specific network, called public-network, my Mac disconnects the VPN connection after 2 minutes and 30 seconds. I have performed several tests and this is the result: It works fine until the 2:30 mark It doesn't matter which Mac I use, it still disconnects It doesn't matter which client I use, all of the following does the same: OSX system client, HMA! Pro VPN and Shimo It doesn't matter which protocol I use, at least all of these protocols does the same: PPTP, OpenVPN and L2TP over IPSec The same thing happens using my own VPN server and HMA!'s VPN server. All other clients (Windows/iPhone) can use any of these VPN servers and protocols without problem on public-network On OSX, all the protocols, clients and servers works fine on any other network So it seems that it is the combination of OSX, VPN & public-network that causes this. This is the syslog from my VPN server, when the disconnection happens: Feb 2 12:04:32 raspberrypi pptpd[31400]: CTRL: EOF or bad error reading ctrl packet length. Feb 2 12:04:32 raspberrypi pptpd[31400]: CTRL: couldn't read packet header (exit) Feb 2 12:04:32 raspberrypi pptpd[31400]: CTRL: CTRL read failed Feb 2 12:04:32 raspberrypi pptpd[31400]: CTRL: Reaping child PPP[31401] Feb 2 12:04:32 raspberrypi pppd[31401]: Hangup (SIGHUP) Feb 2 12:04:32 raspberrypi pppd[31401]: Modem hangup Feb 2 12:04:32 raspberrypi pppd[31401]: Connect time 2.5 minutes. Feb 2 12:04:32 raspberrypi pppd[31401]: Sent 3963649 bytes, received 362775 bytes. Feb 2 12:04:32 raspberrypi pppd[31401]: MPPE disabled Feb 2 12:04:32 raspberrypi pppd[31401]: Connection terminated. Feb 2 12:04:32 raspberrypi pppd[31401]: Exit. Feb 2 12:04:32 raspberrypi pptpd[31400]: CTRL: Client <ip-adress> control connection finished

  Read the article

• Does a 3ware "ECC-ERROR" matter on a JBOD when I have ZFS?

  - by Stefan Lasiewski

  I have a FreeBSD 8.x machine running ZFS and with a 3ware 9690SA controller. The 3ware controller shows an ECC-ERROR with one of the disks: //host> /c0 show VPort Status Unit Size Type Phy Encl-Slot Model ------------------------------------------------------------------------------ p0 OK u0 279.39 GB SAS 0 - SEAGATE ST3300657SS p1 OK u0 279.39 GB SAS 1 - SEAGATE ST3300657SS p2 OK u1 931.51 GB SAS 2 - SEAGATE ST31000640SS p3 ECC-ERROR u2 931.51 GB SAS 3 - SEAGATE ST31000640SS p4 OK u3 931.51 GB SAS 4 - SEAGATE ST31000640SS /c0 show events shows no ECC errors in it's recent history. ZFS does not currently detect any errors. zpool status says No known data errors My question: Is this ECC-ERROR something that I need to be concerned about? According to the 3ware CLI 9.5.2 Manual, an ECC-ERROR means that the 3ware controller caught a read-error for one or more sectors on this drive. This sometimes occurs when a RAID array is recovering from a failed disk. I believe that ECC-ERRORS can also be detected when the 3ware Controller verifies each disk. None of the drives have failed and thus there was no drive rebuild, so I assume that 3ware discovered a bad sector when it ran it's weekly auto-verify scan of the disks. Is this a safe assumption? According to our logs, ZFS has not detected any bad sectors on this drive. ZFS can work around read errors -- if ZFS detects a bad sector on the drive, it will simply mark that sector as bad and never use it again. From the ZFS perspective one bad sector isn't a big deal, although it might indicate that the drive is starting to go bad.

  Read the article

• Change the number of consecutive frequent ssh login before temporary blocking the user login

  - by Kenneth

  my server currently would temporarily refuse a user to login for certain amount of time (maybe ~20min) if the user consecutively frequent ssh login for 3 times. Can I change this behaviour (say relaxed the definition of frequent maybe from 'within 5 sec' to 'within 10 sec'; or increase the # of consecutive login from 3 to 5)? Thanks. Added: Ah.. now I think the problem was not with the ssh. I just tried on another newly installed server. consecutive successful login won't block the user. I have no sudo permission on the server I mentioned above. Now I suspect this behaviour may cause by the firewall in the system. Thanks everyone's comments. ADDED 2: Ah... after some searches. I think the server is using /sbin/iptables to do it as I can see the iptables program is there even though I don't have permission to list the rules. Thanks everyone, special thank to jaume and Mark!

  Read the article

• Opera 10.5 RAM usage and Google Reader?

  - by David

  Hi all, Today I upgraded to Opera 10.5 from Google Chrome and I have two really important questions about it. 1) Is it normal for it to use SO MUCH RAM!!!!? Closing tabs doesn't help, but opening new ones add on to the usage. I can have just 4 tabs open and it goes up to the 300MB mark and I only have 1.5GB in my laptop, 596MB of it used by the graphics card so this really unacceptable. Is there a way to fix it? 2) Why does Google Reader feel so slow and unresponsive on it? It lags so bad when I just try scrolling through the page. I know Opera is known for being really smooth while scrolling through pages. There's also a white bar at the bottom of the page that I can get rid of. It blocks the "Next" and "Previous" buttons. The test between articles is also sort of intersecting each other and that just looks completely unattractive and that's something i'm not used with any web browser. I realize there's a built-in RSS reader, but it doesn't sync across multiple computers and is very late at updating. Here are my specs: Windows 7 Ultimate (x86), Intel Pentium M 1.86 GHz, 1.5GB RAM, ATI Mobility Radeon X600 (64MB dedicated, 596MB shared)

  Read the article

• How to set up QoS on ADSL router (terracom) for prioritizing browsing

  - by DBZ_A

  I want to configure the ADSL router which connects 10+ machines to the internet. I want to give maximum priority to browsing (ports 80,443) and set low priority for bittorrent etc.(port 42180) I have been experimenting with settings , but with no luck. There are three settings which confuse me, along with my understanding. 802.1 Priority - Related to LAN level, possible values 0-7 , higher numbers means higher priority. 'Mark traffic priority' - clueless about this. IPP/DS - IP Precedence - possible values 0-7 ; 6 & 7 are reserved, so set 5 for highest priority. Or when using DSCP - set 46 for highest priority. Please help me in getting this done... Similer question for another model of router here , but with less number of confusing options :) How to configure QoS on home router Update: from discussion on another thread, QoS can control only upstream traffic (from router to the internet) , while this may in turn affect downstream traffic rate, there is no direct control over data coming into the router.

  Read the article

• Overriding routes on Openvpn client, iproute, iptables2

  - by sarvavijJana

  I am looking for some way to route packets based on its destination ports switching regular internet connection and established openvpn tunnel. This is my configuration OpenVPN server ( I have no control over it ) OpenVPN client running ubuntu wlan0 192.168.1.111 - internet connected if Several routes applied on connection to openvpn from server: /sbin/route add -net 207.126.92.3 netmask 255.255.255.255 gw 192.168.1.1 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 5.5.0.1 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 5.5.0.1 And I need to route packets regarding it's destination ports for ex: 80,443 into vpn everything else directly to isp connection 192.168.1.1 What i have used during my attempts: iptables -A OUTPUT -t mangle -p tcp -m multiport ! --dports 80,443 -j MARK --set-xmark 0x1/0xffffffff ip rule add fwmark 0x1 table 100 ip route add default via 192.168.1.1 table 100 I was trying to apply this settings using up/down options of openvpn client configuration All my attempts reduced to successful packet delivery and response only via vpn tunnel. Packets routed bypassing vpn i have used some SNAT to gain proper src address iptables -A POSTROUTING -t nat -o $IF -p tcp -m multiport --dports 80,443 -j SNAT --to $IF_IP failed in SYN-ACK like 0 0,1 0,1: "70","192.168.1.111","X.X.X.X","TCP","34314 > 81 [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=18664016 TSER=0 WS=7" "71","X.X.X.X","192.168.1.111","TCP","81 > 34314 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1428 TSV=531584430 TSER=18654692 WS=5" "72","X.X.X.X","192.168.1.111","TCP","81 > 34314 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1428 TSV=531584779 TSER=18654692 WS=5" "73","192.168.1.111","X.X.X.X","TCP","34343 > 81 [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=18673732 TSER=0 WS=7" I hope someone has already overcome such a situation or probably knows better approach to fulfill requirements. Please kindly give me a good advice or working solution.

  Read the article

• How do photoshop slices and layer comps interact?

  - by Steve314

  I'm interested in using Photoshop (I have CS2) for some user interface design. I was hoping to be able to use slices and layer comps to mark out particular elements, and use Javascript scripting to export multiple graphics files and text descriptions (positions and sizes of slices mainly) that will be used by my program. My problem is that I've never used Photoshop for web design, or otherwise used slices, and I'm not confident that I understand how they interact with layer comps. This is what I believe (and hope) is correct... Manual slices aren't affected by layer comps in any way - they aren't saved as part of a layer comp. The same manual slices will be active irrespective of which layer comp is selected. Layer-based slices aren't directly affected by layer comps, but they are indirectly affected in that the layer comp saves details of layer position and style. Thus selecting a layer comp may move a layer and change its style, affecting the location and size of its layer-based slice, or may effectively disable the slice by hiding the layer. Automatic slices aren't directly affected by layer comps, but are indirectly affected due to changes to the layer-based slices. So, layer based slices (which are my main interest) may move, may change size (to accomodate a style such as a drop shadow), and may be effectively disabled by the layer being hidden. Other details (and all details of manual slices) will remain constant irrespective of which layer comp is active. Is that correct?

  Read the article

• How to get robocopy running in powershell?

  - by Moo MinTroll

  I'm trying to use robocopy inside powershell to mirror some directories on my home machines. Here's my script: param ($configFile) $config = Import-Csv $configFile $what = "/COPYALL /B /SEC/ /MIR" $options = "/R:0 /W:0 /NFL /NDL" $logDir = "C:\Backup\" foreach ($line in $config) { $source = $($line.SourceFolder) $dest = $($line.DestFolder) $logfile = $logDIr $logfile += Split-Path $dest -Leaf $logfile += ".log" robocopy "$source $dest $what $options /LOG:MyLogfile.txt" } The script takes in a csv file with a list of source and destination directories. When I run the script I get these errors: ------------------------------------------------------------------------------- ROBOCOPY :: Robust File Copy for Windows ------------------------------------------------------------------------------- Started : Sat Apr 03 21:26:57 2010 Source : P:\ C:\Backup\Photos \COPYALL \B \SEC\ \MIR \R:0 \W:0 \NFL \NDL \LOG:MyLogfile.txt\ Dest - Files : *.* Options : *.* /COPY:DAT /R:1000000 /W:30 ------------------------------------------------------------------------------ ERROR : No Destination Directory Specified. Simple Usage :: ROBOCOPY source destination /MIR source :: Source Directory (drive:\path or \\server\share\path). destination :: Destination Dir (drive:\path or \\server\share\path). /MIR :: Mirror a complete directory tree. For more usage information run ROBOCOPY /? **** /MIR can DELETE files as well as copy them ! Any idea what I need to do to fix? Thanks, Mark.

  Read the article

• What's the difference between Host and HostName in SSH Config?

  - by Bill Jobs

  The man page says this: Host Host Restricts the following declarations (up to the next Host keyword) to be only for those hosts that match one of the patterns given after the keyword. If more than one pattern is provided, they should be separated by whitespace. A single `*' as a pattern can be used to provide global defaults for all hosts. The host is the hostname argument given on the command line (i.e. the name is not converted to a canonicalized host name before matching). A pattern entry may be negated by prefixing it with an exclamation mark (`!'). If a negated entry is matched, then the Host entry is ignored, regardless of whether any other patterns on the line match. Negated matches are therefore useful to provide exceptions for wildcard matches. See PATTERNS for more information on patterns. HostName HostName Specifies the real host name to log into. This can be used to specify nicknames or abbreviations for hosts. If the hostname contains the character sequence `%h', then this will be replaced with the host name specified on the command line (this is useful for manipulating unqualified names). The default is the name given on the com- mand line. Numeric IP addresses are also permitted (both on the command line and in HostName specifications). For example, when I want to create an SSH Config for GitHub, what should Host and HostName be respectively?

  Read the article

• Suspected Router problems, [closed]

  - by jordon_user

  I am new to this forum. I appreciate any help you can offer. I have been troubleshooting an error with both my WIRED Internet Connection I have 3 desktops running through this working connection (Router) with no problems. Two computers, one laptop and desktop experience the issue. If I connect directly to the Modem, on either, no problem on the internet. Through the Router, my computer connects for a period of time but if ever awaking my comp, or restarting, the yellow explanation mark returns. The only way I can get the connection up = cmd. ipconfig /release, ipconfig /renew. This constant command is annoying and was hoping for a permanent fix. Audio is also not working. I know its likely a driver error, but its an old comp we put together and if there's an easy fix itd be great to hear from you! If you need any more info just let me know. Thanks! THanks guys!

  Read the article

• "Windows cannot find" file when opening Excel spreadsheet

  - by DanH

  For all of my Excel spreadsheets when I attempt to open them (by double-clicking in explorer) I get the message "Windows cannot find C:...". The files are there, and are valid zip files as seen by 7-Zip. There are no apparent lock files in the directories. I did just install Norton-360 over the weekend (replacing Kasperski), but the Norton log shows no events related to Excel. However, while installing Norton I did reboot with some Excel files open. Presumably something is hosed in my Excel configuration but I don't know what. Update (Before actually posting) -- I found an article that suggested turning off Advanced Option "Ignore other applications that use DDE", then doing excel.exe /unregister followed by excel.exe /register. I tried this but I suspect that the two Excel calls were ignored (Excel opened, but no obvious change). With that option off the spreadsheets load OK, but not with it on. And, curiously, spreadsheets load OK with the option on or off if I open Excel first and then open the spreadsheet in it. Does anyone have any idea what effect leaving that option off will have? Update 2 -- I tried running the "repair" option. It said it corrected a couple of config things (without saying what they were), but I still get a failure if I double-click an Excel file with the "Ignore other applications..." option checked. Update 3 -- I managed to fix this problem, but failed at the time to come back and say what I did, and now I can't remember for sure. But I think it had something to do with "Options"/"Save" and some of the values there. Something to do with AutoRecover, perhaps. (Possibly there was a file in recovery and I had to specify "Disable AutoRecover for this workbook" to let bring-up get past it. Or perhaps the AutoRecover file location was hosed.) Anyway, if it happens to someone else, and you find the fix, post it below and I'll mark it answered.

  Read the article

• firefox addon f@stestfox API sending/collecting data?

  - by Richard

  System: ubuntu64/firefox24.0 object: addon "f@stestfox". Its a nice in-browser search tool and more. Problematic: is the way the program handles the search queries. when I use a search shortcut, burpsuite says: request to msgs.smarterfox.com: 80 GET /log_msg?name=popup_bubble_searched&search_engine_title=Search%20Startpage&source=FastestFox&redirect_to=https%3A%2F%2Fstartpage.com%2Fdo%2Fsearch%3Fcmd%3Dprocess_search%26cat%3Dweb%26query%3Dnginx%26language%3Denglish%26no_sugg%3D1%26ff%3D%26abp%3D-1&rand=856827465 HTTP/1.1 Host: msgs.smarterfox.com User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.0) Accept: text/html,application/xhtml+xml,application/xml;q=0.9,/;q=0.8 Accept-Language: en-US,en;q=0.5 Accept-Encoding: gzip, deflate DNT: 1 Connection: keep-alive once I saw a unique identifier (installation time?) was send with the request to the server. Am I right, that the addon sends the website I am looking at to the server? Sometimes I only mark text(ip adress or link) and the addon send this data? seriosly? I did: search for the url in the code, but I dont speak java. And I am not sure, if the data from the request can actually be used for tracking :) question: I want the awesome features of the addon, without connecting to their server: marked text should be send only to the searchmachines. what should I do next? thank you.

  Read the article

• What could cause a WMV to not play to completion in a browser?

  - by Ty W

  A realtor has had videos created for a community she is selling homes for, the people who made the videos gave them to us in WMV format. I can play these videos without any problem in Windows Media Player, VLC, and Quicktime (via Flip4Mac). I can play the videos from their location at videohomeguide.com in my browser without any trouble. However when I upload the files to our server the video stops at about the 1 minute mark in Safari and FireFox on Mac OS X Snow Leopard. I'm not sure if Windows browsers have the same issue because they are loaded using Windows Media Player. http://carolepaul.com/images/uploads/cottageslsjamestown.wmv <- our server, will fail at 1:09ish. http://www.videohomeguide.com/media/cottageslsjamestown.wmv <- should play to completion (3:27ish) The files generate the same MD5 hash on my desktop and on our server. I used WGET to transfer the files, always downloading from videohomeguide.com. Since the files are identical and are playable using VLC/WMP/Quicktime, and playable in the browsers from videohomeguide.com it seems to me that it is some sort of server config... maybe incorrect headers sent to the browsers? Here are the headers sent and received by FireFox on OS X: http://carolepaul.com/images/uploads/cottageslsjamestown.wmv GET /images/uploads/cottageslsjamestown.wmv HTTP/1.1 Host: carolepaul.com User-Agent: Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.6; en-US; rv:1.9.2.2) Gecko/20100316 Firefox/3.6.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 115 Connection: keep-alive HTTP/1.1 200 OK Date: Mon, 29 Mar 2010 20:43:20 GMT Server: Apache/1.3.41 (Unix) PHP/5.2.6 FrontPage/5.0.2.2635 mod_psoft_traffic/0.2 mod_ssl/2.8.31 OpenSSL/0.9.8b Last-Modified: Wed, 02 Dec 2009 18:08:46 GMT Etag: "1e7919c-198eadc-4b16ad2e" Accept-Ranges: bytes Content-Length: 26798812 Keep-Alive: timeout=10, max=200 Connection: Keep-Alive Content-Type: video/x-ms-wmv

  Read the article

• Handle Sysinternals software does not accept -c parameter

  - by Alex

  I am trying to close a handle to a locked file in Windows, using Sysinternals Handle software (http://technet.microsoft.com/en-us/sysinternals/bb896655). First I search for opened handle: handle.exe "C:\Temp" It issues me the following: Far.exe pid: 1144 type: File 2E8: C:\Temp Far.exe pid: 1144 type: File 3A8: C:\Temp Next I run handle.exe with -c parameter. However, whichever number I enter, it does not do anything. I have tried both: 1144, 2E8, 3A8 and 1144 in hex (478) as the software help says it accepts PID in hexademic. Whatever I enter, it just issues the following: Handle v3.46 Copyright (C) 1997-2011 Mark Russinovich Sysinternals - www.sysinternals.com usage: handle [[-a [-l]] [-u] | [-c <handle> [-y]] | [-s]] [-p <process>|<pid>] [name] -a Dump all handle information. -l Just show pagefile-backed section handles. -c Closes the specified handle (interpreted as a hexadecimal number). You must specify the process by its PID. WARNING: Closing handles can cause application or system instability. -y Don't prompt for close handle confirmation. -s Print count of each type of handle open. -u Show the owning user name when searching for handles. -p Dump handles belonging to process (partial name accepted). name Search for handles to objects with <name> (fragment accepted). No arguments will dump all file references. What am I doing wrong?

  Read the article

• openvpn& iptables -- portforwarding and gateway

  - by Smith.Lai

  The problem is similar to this scenario: iptables rule still take effect after deleted Scenario: There are several clients(C1~C10) providing some services, such as SSH,HTTP..... The clients are actually a personal computer behind NAT. Their IP might be 192.168.0.x For easily access these machines through internet, I built a OpenVPN server(S1). All the C1~C10 connect to S1 with VPN address 10.8.0.x If A user(U1) wanna access C1 SSH through internet, he can connect to S1 with port "55555", and S1 port forward 55555 to 10.8.0.6:22 echo 1 /proc/sys/net/ipv4/ip_forward iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 55555 -j DNAT --to-destination 10.8.0.6:22 It works well until I mark the following in the openvpn server.conf: I marked this because I think this will make all connection go through S1 ;push "redirect-gateway" |-------(NAT)--------| (C1)--| (INTERNET)----(U1) |-----(VPN)----(S1)--| The C1~C10 have their own path to access internet resource through NAT . The server loading would be heavy if all C1~C10 connection go through S1 (for example, C1 is sending data to C2, or C1 is downloading data from a FTP site). Is there a way to solve this quandary?

  Read the article

< Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >