Search Results

Search found 3710 results on 149 pages for 'protocol analyzer'.

Page 139/149 | < Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >

  • Cisco ASA 5505 - L2TP over IPsec

    - by xraminx
    I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

    Read the article

  • Apache Tomcat Server failure

    - by Kenneth Ordona
    I'm trying to set up Apache Tomcat 6 with SSL and once I edited the server.xml file to include the following definitions the server started to fail as soon as I hit startup.bat: <-- Define a SSL Coyote HTTP/1.1 Connector on port 8443 -- < Connector protocol="org.apache.coyote.http11.Http11Protocol" port="8445" maxThreads="200" scheme="https" secure="true" SSLEnabled="true" keystoreFile="${user.home}/.tomcat" keystorePass="pnnlpw" clientAuth="false" sslProtocol="TLS"/ The logs that I have are as follows: Jul 05, 2012 1:52:15 PM org.apache.catalina.core.AprLifecycleListener init INFO: The APR based Apache Tomcat Native library which allows optimal performance in production environments was not found on the java.library.path: C:\Program Files\Java\jdk1.7.0_05\bin;C:\WINDOWS\Sun\Java\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;. Jul 05, 2012 1:52:15 PM org.apache.tomcat.util.digester.Digester fatalError SEVERE: Parse Fatal Error at line 91 column 2: The content of elements must consist of well-formed character data or markup. org.xml.sax.SAXParseException; systemId: file://C/tomcat6/conf/server.xml; lineNumber: 91; columnNumber: 2; The content of elements must consist of well-formed character data or markup. at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.createSAXParseException(ErrorHandlerWrapper.java:198) at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.fatalError(ErrorHandlerWrapper.java:177) at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(XMLErrorReporter.java:441) at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(XMLErrorReporter.java:368) at com.sun.org.apache.xerces.internal.impl.XMLScanner.reportFatalError(XMLScanner.java:1388) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl$FragmentContentDriver.startOfMarkup(XMLDocumentFragmentScannerImpl.java:2565) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl$FragmentContentDriver.next(XMLDocumentFragmentScannerImpl.java:2663) at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl.next(XMLDocumentScannerImpl.java:607) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanDocument(XMLDocumentFragmentScannerImpl.java:488) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:835) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:764) at com.sun.org.apache.xerces.internal.parsers.XMLParser.parse(XMLParser.java:123) at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.parse(AbstractSAXParser.java:1210) at com.sun.org.apache.xerces.internal.jaxp.SAXParserImpl$JAXPSAXParser.parse(SAXParserImpl.java:568) at org.apache.tomcat.util.digester.Digester.parse(Digester.java:1642) at org.apache.catalina.startup.Catalina.load(Catalina.java:524) at org.apache.catalina.startup.Catalina.load(Catalina.java:562) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:601) at org.apache.catalina.startup.Bootstrap.load(Bootstrap.java:261) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:413) Jul 05, 2012 1:52:15 PM org.apache.catalina.startup.Catalina load WARNING: Catalina.start using conf/server.xml: org.xml.sax.SAXParseException; systemId: file://C/tomcat6/conf/server.xml; lineNumber: 91; columnNumber: 2; The content of elements must consist of well-formed character data or markup. at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.parse(AbstractSAXParser.java:1236) at com.sun.org.apache.xerces.internal.jaxp.SAXParserImpl$JAXPSAXParser.parse(SAXParserImpl.java:568) at org.apache.tomcat.util.digester.Digester.parse(Digester.java:1642) at org.apache.catalina.startup.Catalina.load(Catalina.java:524) at org.apache.catalina.startup.Catalina.load(Catalina.java:562) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:601) at org.apache.catalina.startup.Bootstrap.load(Bootstrap.java:261) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:413) Jul 05, 2012 1:52:15 PM org.apache.tomcat.util.digester.Digester fatalError SEVERE: Parse Fatal Error at line 91 column 2: The content of elements must consist of well-formed character data or markup. org.xml.sax.SAXParseException; systemId: file://C/tomcat6/conf/server.xml; lineNumber: 91; columnNumber: 2; The content of elements must consist of well-formed character data or markup. at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.createSAXParseException(ErrorHandlerWrapper.java:198) at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.fatalError(ErrorHandlerWrapper.java:177) at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(XMLErrorReporter.java:441) at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(XMLErrorReporter.java:368) at com.sun.org.apache.xerces.internal.impl.XMLScanner.reportFatalError(XMLScanner.java:1388) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl$FragmentContentDriver.startOfMarkup(XMLDocumentFragmentScannerImpl.java:2565) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl$FragmentContentDriver.next(XMLDocumentFragmentScannerImpl.java:2663) at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl.next(XMLDocumentScannerImpl.java:607) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanDocument(XMLDocumentFragmentScannerImpl.java:488) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:835) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(XML11Configuration.java:764) at com.sun.org.apache.xerces.internal.parsers.XMLParser.parse(XMLParser.java:123) at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.parse(AbstractSAXParser.java:1210) at com.sun.org.apache.xerces.internal.jaxp.SAXParserImpl$JAXPSAXParser.parse(SAXParserImpl.java:568) at org.apache.tomcat.util.digester.Digester.parse(Digester.java:1642) at org.apache.catalina.startup.Catalina.load(Catalina.java:524) at org.apache.catalina.startup.Catalina.start(Catalina.java:582) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:601) at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:289) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:414) Jul 05, 2012 1:52:15 PM org.apache.catalina.startup.Catalina load WARNING: Catalina.start using conf/server.xml: org.xml.sax.SAXParseException; systemId: file://C/tomcat6/conf/server.xml; lineNumber: 91; columnNumber: 2; The content of elements must consist of well-formed character data or markup. at com.sun.org.apache.xerces.internal.parsers.AbstractSAXParser.parse(AbstractSAXParser.java:1236) at com.sun.org.apache.xerces.internal.jaxp.SAXParserImpl$JAXPSAXParser.parse(SAXParserImpl.java:568) at org.apache.tomcat.util.digester.Digester.parse(Digester.java:1642) at org.apache.catalina.startup.Catalina.load(Catalina.java:524) at org.apache.catalina.startup.Catalina.start(Catalina.java:582) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:601) at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:289) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:414) Jul 05, 2012 1:52:15 PM org.apache.catalina.startup.Catalina start SEVERE: Cannot start server. Server instance is not configured. Does anyone have an idea why this is happening? I believe it has to do with the configuration of my connector. I'm pretty new to this so any help would be much appreciated.

    Read the article

  • Juniper SSG-5 subinterface vlan routing to the internet

    - by catfish
    I'm unable to get a brand new Juniper SSG-5 with latest 6.3.0r05 firmware routing to the internet from a subinterface I created on bgroup0 setup as vlan2 (bgroup0.1 on "wifi" zone). When connected on the default vlan it gets on the internet just fine. When I switch to vlan2 I'm unable to get to the internet. I am able to get the correct ip address (10.150.0.0/24) from dhcp, able to get to the juniper management page, etc but nothing past the firewall, can't ping 4.2.2.2 or the internet gateway. Even setting up logging on the wifi-to-untrust policy and it does shows the attempts (it's it's timeouts). 172.31.16.0/24 is the untrusted lan, it's already nat'ed but works fine for testing. Can ping this ip from the default vlan but not from vlan2 192.168.1.0/24 is the trusted main lan 10.150.0.0/24 is the wifi isolated lan on vlan2 The idea is to setup an AP with lan and guest access (AP supports multiple ssid's on different vlans). I know I can setup the juniper to use different ports for the wifi lan and use their procurve switch to do the vlan separation, but I never used vlan'ing on a Juniper firewall and I would like to try it out this way. Here is the complete config file: unset key protection enable set clock timezone -5 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "xxxxxxxxxxxxxxxx" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone id 100 "Wifi" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst unset zone "Wifi" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Untrust" set interface "bgroup0" zone "Trust" set interface "bgroup0.1" tag 2 zone "Wifi" set interface "bgroup1" zone "DMZ" set interface bgroup0 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup0 port ethernet0/5 set interface bgroup0 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 172.31.16.243/24 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup0.1 ip 10.150.0.1/24 set interface bgroup0.1 nat set interface bgroup0.1 mtu 1500 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup0.1 ip manageable set interface ethernet0/0 manage ping set interface ethernet0/1 manage ping set interface bgroup0.1 manage ping set interface bgroup0.1 manage telnet set interface bgroup0.1 manage web unset interface bgroup1 manage ping set interface bgroup0 dhcp server service set interface bgroup0.1 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup0.1 dhcp server enable set interface bgroup0 dhcp server option gateway 192.168.1.1 set interface bgroup0 dhcp server option netmask 255.255.255.0 set interface bgroup0 dhcp server option dns1 8.8.8.8 set interface bgroup0.1 dhcp server option lease 1440 set interface bgroup0.1 dhcp server option gateway 10.150.0.1 set interface bgroup0.1 dhcp server option netmask 255.255.255.0 set interface bgroup0.1 dhcp server option dns1 8.8.8.8 set interface bgroup0 dhcp server ip 192.168.1.33 to 192.168.1.126 set interface bgroup0.1 dhcp server ip 10.150.0.50 to 10.150.0.100 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup0.1 dhcp server config next-server-ip set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow no-tcp-seq-check set flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Wifi" to "Untrust" "Any" "Any" "ANY" permit log set policy id 2 exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set snmpv3 local-engine id "0162122009006149" set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route set route 0.0.0.0/0 interface ethernet0/0 gateway 172.31.16.1 exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

    Read the article

  • Combining HBase and HDFS results in Exception in makeDirOnFileSystem

    - by utrecht
    Introduction An attempt to combine HBase and HDFS results in the following: 2014-06-09 00:15:14,777 WARN org.apache.hadoop.hbase.HBaseFileSystem: Create Dir ectory, retries exhausted 2014-06-09 00:15:14,780 FATAL org.apache.hadoop.hbase.master.HMaster: Unhandled exception. Starting shutdown. java.io.IOException: Exception in makeDirOnFileSystem at org.apache.hadoop.hbase.HBaseFileSystem.makeDirOnFileSystem(HBaseFile System.java:136) at org.apache.hadoop.hbase.master.MasterFileSystem.checkRootDir(MasterFi leSystem.java:428) at org.apache.hadoop.hbase.master.MasterFileSystem.createInitialFileSyst emLayout(MasterFileSystem.java:148) at org.apache.hadoop.hbase.master.MasterFileSystem.<init>(MasterFileSyst em.java:133) at org.apache.hadoop.hbase.master.HMaster.finishInitialization(HMaster.j ava:572) at org.apache.hadoop.hbase.master.HMaster.run(HMaster.java:432) at java.lang.Thread.run(Thread.java:744) Caused by: org.apache.hadoop.security.AccessControlException: Permission denied: user=hbase, access=WRITE, inode="/":vagrant:supergroup:drwxr-xr-x at org.apache.hadoop.hdfs.server.namenode.FSPermissionChecker.check(FSPe rmissionChecker.java:224) at org.apache.hadoop.hdfs.server.namenode.FSPermissionChecker.check(FSPe rmissionChecker.java:204) at org.apache.hadoop.hdfs.server.namenode.FSPermissionChecker.checkPermi ssion(FSPermissionChecker.java:149) at org.apache.hadoop.hdfs.server.namenode.FSNamesystem.checkPermission(F SNamesystem.java:4891) at org.apache.hadoop.hdfs.server.namenode.FSNamesystem.checkPermission(F SNamesystem.java:4873) at org.apache.hadoop.hdfs.server.namenode.FSNamesystem.checkAncestorAcce ss(FSNamesystem.java:4847) at org.apache.hadoop.hdfs.server.namenode.FSNamesystem.mkdirsInternal(FS Namesystem.java:3192) at org.apache.hadoop.hdfs.server.namenode.FSNamesystem.mkdirsInt(FSNames ystem.java:3156) at org.apache.hadoop.hdfs.server.namenode.FSNamesystem.mkdirs(FSNamesyst em.java:3137) at org.apache.hadoop.hdfs.server.namenode.NameNodeRpcServer.mkdirs(NameN odeRpcServer.java:669) at org.apache.hadoop.hdfs.protocolPB.ClientNamenodeProtocolServerSideTra nslatorPB.mkdirs(ClientNamenodeProtocolServerSideTranslatorPB.java:419) at org.apache.hadoop.hdfs.protocol.proto.ClientNamenodeProtocolProtos$Cl ientNamenodeProtocol$2.callBlockingMethod(ClientNamenodeProtocolProtos.java:4497 0) at org.apache.hadoop.ipc.ProtobufRpcEngine$Server$ProtoBufRpcInvoker.cal l(ProtobufRpcEngine.java:453) at org.apache.hadoop.ipc.RPC$Server.call(RPC.java:1002) at org.apache.hadoop.ipc.Server$Handler$1.run(Server.java:1752) at org.apache.hadoop.ipc.Server$Handler$1.run(Server.java:1748) at java.security.AccessController.doPrivileged(Native Method) at javax.security.auth.Subject.doAs(Subject.java:422) at org.apache.hadoop.security.UserGroupInformation.doAs(UserGroupInforma tion.java:1438) at org.apache.hadoop.ipc.Server$Handler.run(Server.java:1746) at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstruct orAccessorImpl.java:62) at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingC onstructorAccessorImpl.java:45) at java.lang.reflect.Constructor.newInstance(Constructor.java:408) at org.apache.hadoop.ipc.RemoteException.instantiateException(RemoteExce ption.java:90) at org.apache.hadoop.ipc.RemoteException.unwrapRemoteException(RemoteExc eption.java:57) at org.apache.hadoop.hdfs.DFSClient.primitiveMkdir(DFSClient.java:2153) at org.apache.hadoop.hdfs.DFSClient.mkdirs(DFSClient.java:2122) at org.apache.hadoop.hdfs.DistributedFileSystem.mkdirs(DistributedFileSy stem.java:545) at org.apache.hadoop.fs.FileSystem.mkdirs(FileSystem.java:1915) at org.apache.hadoop.hbase.HBaseFileSystem.makeDirOnFileSystem(HBaseFile System.java:129) ... 6 more while configuration and system settings are as follows: [vagrant@localhost hadoop-hdfs]$ hadoop fs -ls hdfs://localhost/ Found 1 items -rw-r--r-- 3 vagrant supergroup 1010827264 2014-06-08 19:01 hdfs://localhost/u buntu-14.04-desktop-amd64.iso [vagrant@localhost hadoop-hdfs]$ /etc/hadoop/conf/core-site.xml <configuration> <property> <name>fs.defaultFS</name> <value>hdfs://localhost:8020</value> </property> </configuration> /etc/hbase/conf/hbase-site.xml <configuration> <property> <name>hbase.rootdir</name> <value>hdfs://localhost:8020/hbase</value> </property> <property> <name>hbase.cluster.distributed</name> <value>true</value> </property> </configuration> /etc/hadoop/conf/hdfs-site.xml <configuration> <property> <name>dfs.name.dir</name> <value>/var/lib/hadoop-hdfs/cache</value> </property> <property> <name>dfs.data.dir</name> <value>/tmp/hellodatanode</value> </property> </configuration> NameNode directory permissions [vagrant@localhost hadoop-hdfs]$ ls -ltr /var/lib/hadoop-hdfs/cache total 8 -rwxrwxrwx. 1 hbase hdfs 15 Jun 8 23:43 in_use.lock drwxrwxrwx. 2 hbase hdfs 4096 Jun 8 23:43 current [vagrant@localhost hadoop-hdfs]$ HMaster is able to start if fs.defaultFS property has been commented in core-site.xml NameNode is listening [vagrant@localhost hadoop-hdfs]$ netstat -nato | grep 50070 tcp 0 0 0.0.0.0:50070 0.0.0.0:* LIST EN off (0.00/0/0) tcp 0 0 33.33.33.33:50070 33.33.33.1:57493 ESTA BLISHED off (0.00/0/0) and accessible by navigating to http://33.33.33.33:50070/dfshealth.jsp. Question How to solve makeDirOnFileSystem exception and let HBase connect to HDFS?

    Read the article

  • installed openstack using devstack install shell script but getting 500 error when i try opening dashboard

    - by Arvind
    I followed the instructions at http://devstack.org/guides/single-machine.html to install OpenStack. I first installed Ubuntu on my Windows 7 PC using the officially supported Windows installer for Ubuntu 12.04 LTS. And after that I followed the instructions at above page to install OpenStack. As per instructions, I should be able to access the dashboard aka Horizon, at http://192.168.1.4/ (thats the IP of the PC on which I installed Ubuntu-OpenStack). However I am getting a 500 error web page when I open that. How do I resolve this error? I want to set up a dev environment for OpenStack. For your ref, the whole error message is given now-- FilterError at / /usr/bin/env: node: No such file or directory Request Method: GET Request URL: http://192.168.1.4/ Django Version: 1.4.2 Exception Type: FilterError Exception Value: /usr/bin/env: node: No such file or directory Exception Location: /usr/local/lib/python2.7/dist-packages/compressor/filters/base.py in input, line 133 Python Executable: /usr/bin/python Python Version: 2.7.3 Python Path: ['/opt/stack/horizon/openstack_dashboard/wsgi/../..', '/opt/stack/python-keystoneclient', '/opt/stack/python-novaclient', '/opt/stack/python-openstackclient', '/opt/stack/keystone', '/opt/stack/glance', '/opt/stack/python-glanceclient/setuptools_git-0.4.2-py2.7.egg', '/opt/stack/python-glanceclient', '/opt/stack/nova', '/opt/stack/horizon', '/opt/stack/cinder', '/opt/stack/python-cinderclient', '/usr/local/lib/python2.7/dist-packages', '/usr/lib/python2.7', '/usr/lib/python2.7/plat-linux2', '/usr/lib/python2.7/lib-tk', '/usr/lib/python2.7/lib-old', '/usr/lib/python2.7/lib-dynload', '/usr/lib/python2.7/dist-packages', '/usr/lib/python2.7/dist-packages/PIL', '/usr/lib/python2.7/dist-packages/gst-0.10', '/usr/lib/python2.7/dist-packages/gtk-2.0', '/usr/lib/pymodules/python2.7', '/usr/lib/python2.7/dist-packages/ubuntu-sso-client', '/usr/lib/python2.7/dist-packages/ubuntuone-client', '/usr/lib/python2.7/dist-packages/ubuntuone-control-panel', '/usr/lib/python2.7/dist-packages/ubuntuone-couch', '/usr/lib/python2.7/dist-packages/ubuntuone-storage-protocol', '/opt/stack/horizon/openstack_dashboard'] Server time: Sat, 27 Oct 2012 08:43:29 +0000 Error during template rendering In template /opt/stack/horizon/openstack_dashboard/templates/_stylesheets.html, error at line 3 /usr/bin/env: node: No such file or directory 1 {% load compress %} 2 3 {% compress css %} 4 <link href='{{ STATIC_URL }}dashboard/less/horizon.less' type='text/less' media='screen' rel='stylesheet' /> 5 {% endcompress %} 6 7 <link rel="shortcut icon" href="{{ STATIC_URL }}dashboard/img/favicon.ico"/> 8 Also, the traceback is now given below-- Environment: Request Method: GET Request URL: http://192.168.1.4/ Django Version: 1.4.2 Python Version: 2.7.3 Installed Applications: ('openstack_dashboard', 'django.contrib.contenttypes', 'django.contrib.auth', 'django.contrib.sessions', 'django.contrib.messages', 'django.contrib.staticfiles', 'django.contrib.humanize', 'compressor', 'horizon', 'openstack_dashboard.dashboards.project', 'openstack_dashboard.dashboards.admin', 'openstack_dashboard.dashboards.settings', 'openstack_auth') Installed Middleware: ('django.middleware.common.CommonMiddleware', 'django.middleware.csrf.CsrfViewMiddleware', 'django.contrib.sessions.middleware.SessionMiddleware', 'django.contrib.auth.middleware.AuthenticationMiddleware', 'django.contrib.messages.middleware.MessageMiddleware', 'horizon.middleware.HorizonMiddleware', 'django.middleware.doc.XViewMiddleware', 'django.middleware.locale.LocaleMiddleware') Template error: In template /opt/stack/horizon/openstack_dashboard/templates/_stylesheets.html, error at line 3 /usr/bin/env: node: No such file or directory 1 : {% load compress %} 2 : 3 : {% compress css %} 4 : <link href='{{ STATIC_URL }}dashboard/less/horizon.less' type='text/less' media='screen' rel='stylesheet' /> 5 : {% endcompress %} 6 : 7 : <link rel="shortcut icon" href="{{ STATIC_URL }}dashboard/img/favicon.ico"/> 8 : Traceback: File "/usr/local/lib/python2.7/dist-packages/django/core/handlers/base.py" in get_response 111. response = callback(request, *callback_args, **callback_kwargs) File "/usr/local/lib/python2.7/dist-packages/django/views/decorators/vary.py" in inner_func 36. response = func(*args, **kwargs) File "/opt/stack/horizon/openstack_dashboard/wsgi/../../openstack_dashboard/views.py" in splash 38. return shortcuts.render(request, 'splash.html', {'form': form}) File "/usr/local/lib/python2.7/dist-packages/django/shortcuts/__init__.py" in render 44. return HttpResponse(loader.render_to_string(*args, **kwargs), File "/usr/local/lib/python2.7/dist-packages/django/template/loader.py" in render_to_string 176. return t.render(context_instance) File "/usr/local/lib/python2.7/dist-packages/django/template/base.py" in render 140. return self._render(context) File "/usr/local/lib/python2.7/dist-packages/django/template/base.py" in _render 134. return self.nodelist.render(context) File "/usr/local/lib/python2.7/dist-packages/django/template/base.py" in render 823. bit = self.render_node(node, context) File "/usr/local/lib/python2.7/dist-packages/django/template/debug.py" in render_node 74. return node.render(context) File "/usr/local/lib/python2.7/dist-packages/django/template/loader_tags.py" in render 155. return self.render_template(self.template, context) File "/usr/local/lib/python2.7/dist-packages/django/template/loader_tags.py" in render_template 137. output = template.render(context) File "/usr/local/lib/python2.7/dist-packages/django/template/base.py" in render 140. return self._render(context) File "/usr/local/lib/python2.7/dist-packages/django/template/base.py" in _render 134. return self.nodelist.render(context) File "/usr/local/lib/python2.7/dist-packages/django/template/base.py" in render 823. bit = self.render_node(node, context) File "/usr/local/lib/python2.7/dist-packages/django/template/debug.py" in render_node 74. return node.render(context) File "/usr/local/lib/python2.7/dist-packages/compressor/templatetags/compress.py" in render 147. return self.render_compressed(context, self.kind, self.mode, forced=forced) File "/usr/local/lib/python2.7/dist-packages/compressor/templatetags/compress.py" in render_compressed 107. rendered_output = self.render_output(compressor, mode, forced=forced) File "/usr/local/lib/python2.7/dist-packages/compressor/templatetags/compress.py" in render_output 119. return compressor.output(mode, forced=forced) File "/usr/local/lib/python2.7/dist-packages/compressor/css.py" in output 51. ret.append(subnode.output(*args, **kwargs)) File "/usr/local/lib/python2.7/dist-packages/compressor/css.py" in output 53. return super(CssCompressor, self).output(*args, **kwargs) File "/usr/local/lib/python2.7/dist-packages/compressor/base.py" in output 230. content = self.filter_input(forced) File "/usr/local/lib/python2.7/dist-packages/compressor/base.py" in filter_input 192. for hunk in self.hunks(forced): File "/usr/local/lib/python2.7/dist-packages/compressor/base.py" in hunks 167. precompiled, value = self.precompile(value, **options) File "/usr/local/lib/python2.7/dist-packages/compressor/base.py" in precompile 210. command=command, filename=filename).input(**kwargs) File "/usr/local/lib/python2.7/dist-packages/compressor/filters/base.py" in input 133. raise FilterError(err) Exception Type: FilterError at / Exception Value: /usr/bin/env: node: No such file or directory

    Read the article

  • howto only tunnel specific hosts route through openvpn client on tomato

    - by kcome
    I am relatively newbie in networking world although I did coding and know some sysadmin background for a long time. and here I'm only one step from my destination. The whole picture is : at home I use one LinkSys E3000 as the gateway(don't know yet if this is it's name), wireless AP and no other routing/switching devices. It serves 1 PC and 1 Mac with LAN, 1 Mac Mini + 1 iPad + 2 smartphones with WIFI. My goal is use an openvpn client on the E3000 (with tomato firmware) and make my iPad and smartphone's all WiFi traffic through it, and other devices route remain the same non-openvpn route. So far I'm able to connect openvpn client on E3000 to an openvpn server, tunnel all my devices' all traffic through that openvpn connection. What's left is howto selectively route by source IP (at least in my guessing) to the tunnel while don't bother others. I had learned some 'iptables' and 'route' in past few days however without much luck, so here comes my question. Here are some info which will help you get the structure. ifconfig -a output, some useless lines striped, and in the web interface C0:C1:C0:1A:E0:28 is WAN, C0:C1:C0:1A:E0:27 is LAN, C0:C1:C0:1A:E0:29 is 2.4G wifi AP, C0:C1:C0:1A:E0:2A is 5G wifi AP. root@router:/tmp/home/root# ifconfig -a br0 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:27 inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:27 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth1 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:29 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 eth2 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:2A UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host ppp0 Link encap:Point-to-Point Protocol inet addr:172.200.1.43 P-t-P:172.200.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING MULTICAST MTU:1480 Metric:1 vlan1 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:27 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 vlan2 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:28 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 wl0.1 Link encap:Ethernet HWaddr C0:C1:C0:1A:E0:29 BROADCAST MULTICAST MTU:1500 Metric:1 brctl show output root@router:/tmp/home/root# brctl show bridge name bridge id STP enabled interfaces br0 8000.c0c1c01ae027 no vlan1 eth1 eth2 before openvpn route-up script root@router:/tmp/home/root# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.200.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 172.200.0.1 0.0.0.0 UG 0 0 0 ppp0 openvpn server push PUSH: Received control message: 'PUSH_REPLY,redirect-gateway,dhcp-option DNS 8.8.8.8,route 172.20.0.1,topology net30,ping 10,ping-restart 120,ifconfig 172.20.0.6 172.20.0.5' openvpn's stock route-up script Apr 24 14:52:06 router daemon.notice openvpn[1768]: /sbin/ifconfig tun11 172.20.0.6 pointopoint 172.20.0.5 mtu 1500 Apr 24 14:52:08 router daemon.notice openvpn[1768]: /sbin/route add -net 72.14.177.29 netmask 255.255.255.255 gw 172.200.0.1 Apr 24 14:52:08 router daemon.notice openvpn[1768]: /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 172.20.0.5 Apr 24 14:52:08 router daemon.notice openvpn[1768]: /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 172.20.0.5 Apr 24 14:52:08 router daemon.notice openvpn[1768]: /sbin/route add -net 172.20.0.1 netmask 255.255.255.255 gw 172.20.0.5 route after openvpn root@router:/tmp/home/root# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.20.0.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun11 72.14.177.29 172.200.0.1 255.255.255.255 UGH 0 0 0 ppp0 172.200.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 172.20.0.1 172.20.0.5 255.255.255.255 UGH 0 0 0 tun11 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 172.20.0.5 128.0.0.0 UG 0 0 0 tun11 128.0.0.0 172.20.0.5 128.0.0.0 UG 0 0 0 tun11 0.0.0.0 172.200.0.1 0.0.0.0 UG 0 0 0 ppp0 something I had noticed and tried: * on the web interface of openvpn client there is an option "Create NAT on tunnel", if i check this, there is the following script (probably executed after openvpn connection established) root@router:/tmp/home/root# cat /tmp/etc/openvpn/fw/client1-fw.sh #!/bin/sh iptables -I INPUT -i tun11 -j ACCEPT iptables -I FORWARD -i tun11 -j ACCEPT iptables -t nat -I POSTROUTING -s 192.168.1.0/255.255.255.0 -o tun11 -j MASQUERADE if i uncheck this option, the last line will not appear. Then I guess probably the my issue will be solved by iptables and NAT related commands, I just haven't got enough knowledge to figure them out. I tried run iptables -t nat -I POSTROUTING -s 192.168.1.6 -o tun11 -j MASQUERADE manually after openvpn connected (192.168.1.6 is the ip address of my iPad), then my iPad get internet with openvpn tunnel, however all other devices can't reach internet. in case if needed, here is the iptables about NAT root@router:/tmp/home/root# iptables -t nat -L -n Chain PREROUTING (policy ACCEPT) target prot opt source destination DROP all -- 0.0.0.0/0 192.168.1.0/24 WANPREROUTING all -- 0.0.0.0/0 172.200.1.43 upnp all -- 0.0.0.0/0 172.200.1.43 Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- 0.0.0.0/0 0.0.0.0/0 SNAT all -- 192.168.1.0/24 192.168.1.0/24 to:192.168.1.1 Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain WANPREROUTING (1 references) target prot opt source destination DNAT icmp -- 0.0.0.0/0 0.0.0.0/0 to:192.168.1.1 Chain upnp (1 references) target prot opt source destination DNAT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:5353 to:192.168.1.3:5353 Thanks in advance for helping and read this so much, I hope i made every info you need to give a help :)

    Read the article

  • DRBD Not syncing between my nodes

    - by Mike Curry
    Some version info: Operating system is Ubuntu 11.10, on EC2, kernel is 3.0.0-16-virtual and the application info is: Version: 8.3.11 (api:88) GIT-hash: 0de839cee13a4160eed6037c4bddd066645e23c5 build by buildd@allspice, 2011-07-05 19:51:07 Getting some strange errors in dmesg (seen below) as well, there is no replication happening. I have made my first node primary and its showing: drbd driver loaded OK; device status: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 m:res cs ro ds p mounted fstype 0:r0 StandAlone Primary/Unknown UpToDate/DUnknown r----s ext3 my secondary node is showing: drbd driver loaded OK; device status: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 m:res cs ro ds p mounted fstype 0:r0 StandAlone Secondary/Unknown Inconsistent/DUnknown r----s Showing /proc/drbd on the master shows: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 0: cs:StandAlone ro:Primary/Unknown ds:UpToDate/DUnknown r----s ns:0 nr:0 dw:4 dr:1073 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:262135964 Showing /proc/drbd on the slave shows that there is nothing being transfered... version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 0: cs:StandAlone ro:Secondary/Unknown ds:Inconsistent/DUnknown r----s ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:262135964 Here is my config... resource r0 { protocol C; startup { wfc-timeout 15; degr-wfc-timeout 60; } net { cram-hmac-alg sha1; shared-secret "test123; } on drbd01 { device /dev/drbd0; disk /dev/xvdm; address 23.XX.XX.XX:7788; # blocked out ip meta-disk internal; } on drbd02 { device /dev/drbd0; disk /dev/xvdm; address 184.XX.XX.XX:7788; #blocked out ip meta-disk internal; } } I have run the following on the master: sudo drbdadm -- --overwrite-data-of-peer primary all There is no firewall between the systems. Here is the dmesg with some errors: [2285172.969955] drbd: initialized. Version: 8.3.11 (api:88/proto:86-96) [2285172.969960] drbd: srcversion: DA5A13F16DE6553FC7CE9B2 [2285172.969962] drbd: registered as block device major 147 [2285172.969965] drbd: minor_table @ 0xffff88000276ea00 [2285173.000952] block drbd0: Starting worker thread (from drbdsetup [1300]) [2285173.003971] block drbd0: disk( Diskless -> Attaching ) [2285173.006150] block drbd0: No usable activity log found. [2285173.006154] block drbd0: Method to ensure write ordering: flush [2285173.006158] block drbd0: max BIO size = 4096 [2285173.006165] block drbd0: drbd_bm_resize called with capacity == 524271928 [2285173.008512] block drbd0: resync bitmap: bits=65533991 words=1023969 pages=2000 [2285173.008518] block drbd0: size = 250 GB (262135964 KB) [2285173.079566] block drbd0: bitmap READ of 2000 pages took 17 jiffies [2285173.081189] block drbd0: recounting of set bits took additional 1 jiffies [2285173.081194] block drbd0: 250 GB (65533991 bits) marked out-of-sync by on disk bit-map. [2285173.081203] block drbd0: Suspended AL updates [2285173.081210] block drbd0: disk( Attaching -> UpToDate ) [2285173.081214] block drbd0: attached to UUIDs 1C1291D39584C1D1:0000000000000004:0000000000000000:0000000000000000 [2285173.095016] block drbd0: conn( StandAlone -> Unconnected ) [2285173.095046] block drbd0: Starting receiver thread (from drbd0_worker [1301]) [2285173.099297] block drbd0: receiver (re)started [2285173.099304] block drbd0: conn( Unconnected -> WFConnection ) [2285173.099330] block drbd0: bind before connect failed, err = -99 [2285173.099346] block drbd0: conn( WFConnection -> Disconnecting ) [2285173.295788] block drbd0: Discarding network configuration. [2285173.295815] block drbd0: Connection closed [2285173.295826] block drbd0: conn( Disconnecting -> StandAlone ) [2285173.295840] block drbd0: receiver terminated [2285173.295844] block drbd0: Terminating drbd0_receiver Edit: Reading some other similar issues, it was suggested to do a 'drbdadm dump all', so I figured it couldn't hurt. ubuntu@drbd01:~$ drbdadm dump all /etc/drbd.conf:19: in resource r0, on drbd01: IP 23.XX.XX.XX not found on this host. and on slave: root@drbd02:~# drbdadm dump all /etc/drbd.conf:25: in resource r0, on drbd02: IP 184.XX.XX.XX not found on this host. Strange it doesn't find its own ip, however, this is an Amazon EC2 system using an elastic IP... here are my ipconfigs for both... master: ubuntu@drbd01:~$ ifconfig eth0 Link encap:Ethernet HWaddr 22:00:0a:1c:27:11 inet addr:10.28.39.17 Bcast:10.28.39.63 Mask:255.255.255.192 inet6 addr: fe80::2000:aff:fe1c:2711/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1569 errors:0 dropped:0 overruns:0 frame:0 TX packets:1169 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:124409 (124.4 KB) TX bytes:213601 (213.6 KB) Interrupt:26 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) slave: root@drbd02:~# ifconfig eth0 Link encap:Ethernet HWaddr 12:31:3f:00:14:9d inet addr:10.160.27.107 Bcast:10.160.27.255 Mask:255.255.254.0 inet6 addr: fe80::1031:3fff:fe00:149d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:915 errors:0 dropped:0 overruns:0 frame:0 TX packets:774 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:75381 (75.3 KB) TX bytes:109673 (109.6 KB) Interrupt:26 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

    Read the article

  • SonicOS Enhanced 5.8.1.2 L2TP VPN Authentication Failed

    - by Dean A. Vassallo
    I have a SonicWall TZ 215 running SonicOS Enhanced 5.8.1.2-6o. I have configured the L2TP VPN using the default crypto suite ESP: 3DES/HMAC SHA1 (IKE). Proposals are as such: IKE (Phase 1) Proposal DH Group: Group 2 Encryption: 3DES Authentication: SHA1 Life Time (seconds): 28800 Ipsec (Phase 2) Proposal Protocol: ESP Encryption: 3DES Authentication: SHA1 Enable Perfect Forward Secrecy DISABLED Life Time (seconds): 28800 When attempting to connect via my Mac OS X client I get an authentication error. It appears to pass the pre-authentication but fails to complete. I am at a complete loss. I reconfigured from scratch multiple times...used simple usernames and passwords to verify this wasn't a miskeyed password issue. I have Here are the logs (noted IP has been removed for privacy): 7/1/13 8:19:05.174 PM pppd[1268]: setup_security_context server port: 0x1503 7/1/13 8:19:05.190 PM pppd[1268]: publish_entry SCDSet() failed: Success! 7/1/13 8:19:05.191 PM pppd[1268]: publish_entry SCDSet() failed: Success! 7/1/13 8:19:05.191 PM pppd[1268]: pppd 2.4.2 (Apple version 727.1.1) started by dean, uid 501 7/1/13 8:19:05.192 PM pppd[1268]: L2TP connecting to server ‘0.0.0.0’ (0.0.0.0)... 7/1/13 8:19:05.193 PM pppd[1268]: IPSec connection started 7/1/13 8:19:05.208 PM racoon[1269]: accepted connection on vpn control socket. 7/1/13 8:19:05.209 PM racoon[1269]: Connecting. 7/1/13 8:19:05.209 PM racoon[1269]: IPSec Phase 1 started (Initiated by me). 7/1/13 8:19:05.209 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). 7/1/13 8:19:05.209 PM racoon[1269]: >>>>> phase change status = Phase 1 started by us 7/1/13 8:19:05.231 PM racoon[1269]: >>>>> phase change status = Phase 1 started by peer 7/1/13 8:19:05.231 PM racoon[1269]: IKE Packet: receive success. (Initiator, Main-Mode message 2). 7/1/13 8:19:05.234 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Main-Mode message 3). 7/1/13 8:19:05.293 PM racoon[1269]: IKE Packet: receive success. (Initiator, Main-Mode message 4). 7/1/13 8:19:05.295 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Main-Mode message 5). 7/1/13 8:19:05.315 PM racoon[1269]: IKEv1 Phase 1 AUTH: success. (Initiator, Main-Mode Message 6). 7/1/13 8:19:05.315 PM racoon[1269]: IKE Packet: receive success. (Initiator, Main-Mode message 6). 7/1/13 8:19:05.315 PM racoon[1269]: IKEv1 Phase 1 Initiator: success. (Initiator, Main-Mode). 7/1/13 8:19:05.315 PM racoon[1269]: IPSec Phase 1 established (Initiated by me). 7/1/13 8:19:06.307 PM racoon[1269]: IPSec Phase 2 started (Initiated by me). 7/1/13 8:19:06.307 PM racoon[1269]: >>>>> phase change status = Phase 2 started 7/1/13 8:19:06.308 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). 7/1/13 8:19:06.332 PM racoon[1269]: attribute has been modified. 7/1/13 8:19:06.332 PM racoon[1269]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). 7/1/13 8:19:06.332 PM racoon[1269]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). 7/1/13 8:19:06.333 PM racoon[1269]: IKEv1 Phase 2 Initiator: success. (Initiator, Quick-Mode). 7/1/13 8:19:06.333 PM racoon[1269]: IPSec Phase 2 established (Initiated by me). 7/1/13 8:19:06.333 PM racoon[1269]: >>>>> phase change status = Phase 2 established 7/1/13 8:19:06.333 PM pppd[1268]: IPSec connection established 7/1/13 8:19:07.145 PM pppd[1268]: L2TP connection established. 7/1/13 8:19:07.000 PM kernel[0]: ppp0: is now delegating en0 (type 0x6, family 2, sub-family 3) 7/1/13 8:19:07.146 PM pppd[1268]: Connect: ppp0 <--> socket[34:18] 7/1/13 8:19:08.709 PM pppd[1268]: MS-CHAPv2 mutual authentication failed. 7/1/13 8:19:08.710 PM pppd[1268]: Connection terminated. 7/1/13 8:19:08.710 PM pppd[1268]: L2TP disconnecting... 7/1/13 8:19:08.711 PM pppd[1268]: L2TP disconnected 7/1/13 8:19:08.711 PM racoon[1269]: IPSec disconnecting from server 0.0.0.0 7/1/13 8:19:08.711 PM racoon[1269]: IKE Packet: transmit success. (Information message). 7/1/13 8:19:08.712 PM racoon[1269]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). 7/1/13 8:19:08.712 PM racoon[1269]: IKE Packet: transmit success. (Information message). 7/1/13 8:19:08.712 PM racoon[1269]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). 7/1/13 8:19:08.713 PM racoon[1269]: glob found no matches for path "/var/run/racoon/*.conf" 7/1/13 8:19:08.714 PM racoon[1269]: pfkey DELETE failed: No such file or directory

    Read the article

  • Poor upload/download speed on 2 x ADSL lines into a Cisco 2621XM

    - by 2020mobile
    Hi, Sorry never been on this site before so I apologise if not the right section or even forum. I have users complaining of very slow internetn connectivity on site and have checked with our ISP who have said that the line is testing at 8mb. We have 2 x BT lines that have our ISP broadand on them. Both lines go into a Cisco 2600 series router that then has a PIX firewall off that. Connectivity is successful just gone really slow and unable to download anything. Config is below: version 12.3 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname ROUTER-ADSL-INTERNET ! logging buffered 16384 informational enable secret xxx enable password xxx ! username xxx username xxx clock summer-time UK recurring last Sun Mar 1:00 last Sun Oct 1:00 aaa new-model ! ! aaa authentication login default local aaa authorization exec default local aaa session-id common ip subnet-zero no ip source-route ! ! ! ip audit notify log ip audit po max-events 100 no ip bootp server ip name-server 213.208.106.212 no mpls ldp logging neighbor-changes no ftp-server write-enable ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! ! ! ! ! ! ! interface ATM0/0 description 01270 111111 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface FastEthernet0/0 ip address 82.133.32.9 255.255.255.248 shutdown speed 100 full-duplex no cdp enable ! interface ATM0/1 description 01270 222222 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface FastEthernet0/1 ip address 217.146.115.49 255.255.255.240 duplex auto speed auto no cdp enable ! interface Dialer0 ip address 217.146.115.250 255.255.255.248 encapsulation ppp dialer pool 1 dialer-group 1 ppp authentication chap callin ppp chap hostname [email protected] ppp chap password 7 xxxxx ppp multilink ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! no logging trap access-list 10 permit 217.146.115.50 access-list 10 permit 82.133.32.10 access-list 10 deny any access-list 22 permit 217.146.115.50 access-list 22 permit 217.206.239.86 access-list 22 permit 82.133.32.10 access-list 22 deny any dialer-list 1 protocol ip permit no cdp run ! ! snmp-server community xxxxxx RO 10 snmp-server enable traps tty radius-server authorization permit missing Service-Type ! ! ! ! ! ! line con 0 exec-timeout 5 0 password 7 xxxxxx line aux 0 no exec line vty 0 4 access-class 22 in exec-timeout 5 0 password 7 xxxxxx transport input telnet ssh transport output none line vty 5 15 password 7 xxxxxx transport input telnet ssh ! ntp clock-period 17180095 ntp server 130.88.200.98 ! ! end Now my knowledge is very limited but ISP have said that while the lines are bonded each needs a seperate login as they've recently changed their L2TP router and that enforces the use of seperate logins - when the lines were configured we were given two logins. So, my question is what changes do I need to make to the config in order to get this working? it was ok before their change and I do have another login :- 01270 111111 - [email protected] 01270 222222 - [email protected] Apologies for the long email and thanks for taking the time to read it. Any more info I can provide please let me know. Thanks,

    Read the article

  • OpenVPN on Ubuntu 11.10 - unable to redirect default gateway

    - by Vladimir Kadalashvili
    I'm trying to connect to connect to OpenVPN server from my Ubuntu 11.10 machine. I use the following command to do it (under root user): openvpn --config /home/vladimir/client.ovpn Everything seems to be OK, it connects normally without any warnings and errors, but when I try to browse the internet I see that I still use my own IP address, so VPN connection doesn't work. When I run openvpn command, it displays the following message among others: NOTE: unable to redirect default gateway -- Cannot read current default gateway from system I think it's the cause of this problem, but unfortunately I don't know how to fix it. Below is full output of openvpn command: Sat Jun 9 23:51:36 2012 OpenVPN 2.2.0 x86_64-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [eurephia] [MH] [PF_INET6] [IPv6 payload 20110424-2 (2.2RC2)] built on Jul 4 2011 Sat Jun 9 23:51:36 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Sat Jun 9 23:51:36 2012 Control Channel Authentication: tls-auth using INLINE static key file Sat Jun 9 23:51:36 2012 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Sat Jun 9 23:51:36 2012 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Sat Jun 9 23:51:36 2012 LZO compression initialized Sat Jun 9 23:51:36 2012 Control Channel MTU parms [ L:1542 D:166 EF:66 EB:0 ET:0 EL:0 ] Sat Jun 9 23:51:36 2012 Socket Buffers: R=[126976->200000] S=[126976->200000] Sat Jun 9 23:51:36 2012 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Sat Jun 9 23:51:36 2012 Local Options hash (VER=V4): '504e774e' Sat Jun 9 23:51:36 2012 Expected Remote Options hash (VER=V4): '14168603' Sat Jun 9 23:51:36 2012 UDPv4 link local: [undef] Sat Jun 9 23:51:36 2012 UDPv4 link remote: [AF_INET]94.229.78.130:1194 Sat Jun 9 23:51:37 2012 TLS: Initial packet from [AF_INET]94.229.78.130:1194, sid=13fd921b b42072ab Sat Jun 9 23:51:37 2012 VERIFY OK: depth=1, /CN=OpenVPN_CA Sat Jun 9 23:51:37 2012 VERIFY OK: nsCertType=SERVER Sat Jun 9 23:51:37 2012 VERIFY OK: depth=0, /CN=OpenVPN_Server Sat Jun 9 23:51:38 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Sat Jun 9 23:51:38 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sat Jun 9 23:51:38 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Sat Jun 9 23:51:38 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sat Jun 9 23:51:38 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Sat Jun 9 23:51:38 2012 [OpenVPN_Server] Peer Connection Initiated with [AF_INET]94.229.78.130:1194 Sat Jun 9 23:51:40 2012 SENT CONTROL [OpenVPN_Server]: 'PUSH_REQUEST' (status=1) Sat Jun 9 23:51:40 2012 PUSH: Received control message: 'PUSH_REPLY,explicit-exit-notify,topology subnet,route-delay 5 30,dhcp-pre-release,dhcp-renew,dhcp-release,route-metric 101,ping 5,ping-restart 40,redirect-gateway def1,redirect-gateway bypass-dhcp,redirect-gateway autolocal,route-gateway 5.5.0.1,dhcp-option DNS 8.8.8.8,dhcp-option DNS 8.8.4.4,register-dns,comp-lzo yes,ifconfig 5.5.117.43 255.255.0.0' Sat Jun 9 23:51:40 2012 Unrecognized option or missing parameter(s) in [PUSH-OPTIONS]:4: dhcp-pre-release (2.2.0) Sat Jun 9 23:51:40 2012 Unrecognized option or missing parameter(s) in [PUSH-OPTIONS]:5: dhcp-renew (2.2.0) Sat Jun 9 23:51:40 2012 Unrecognized option or missing parameter(s) in [PUSH-OPTIONS]:6: dhcp-release (2.2.0) Sat Jun 9 23:51:40 2012 Unrecognized option or missing parameter(s) in [PUSH-OPTIONS]:16: register-dns (2.2.0) Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: timers and/or timeouts modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: explicit notify parm(s) modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: LZO parms modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: --ifconfig/up options modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: route options modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: route-related options modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified Sat Jun 9 23:51:40 2012 ROUTE: default_gateway=UNDEF Sat Jun 9 23:51:40 2012 TUN/TAP device tun0 opened Sat Jun 9 23:51:40 2012 TUN/TAP TX queue length set to 100 Sat Jun 9 23:51:40 2012 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0 Sat Jun 9 23:51:40 2012 /sbin/ifconfig tun0 5.5.117.43 netmask 255.255.0.0 mtu 1500 broadcast 5.5.255.255 Sat Jun 9 23:51:45 2012 NOTE: unable to redirect default gateway -- Cannot read current default gateway from system Sat Jun 9 23:51:45 2012 Initialization Sequence Completed Output of route command: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default * 0.0.0.0 U 0 0 0 ppp0 5.5.0.0 * 255.255.0.0 U 0 0 0 tun0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.0.0 * 255.255.255.0 U 0 0 0 wlan0 stream-ts1.net. * 255.255.255.255 UH 0 0 0 ppp0 Output of ifconfig command: eth0 Link encap:Ethernet HWaddr 6c:62:6d:44:0d:12 inet6 addr: fe80::6e62:6dff:fe44:d12/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:54594 errors:0 dropped:0 overruns:0 frame:0 TX packets:59897 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44922107 (44.9 MB) TX bytes:8839969 (8.8 MB) Interrupt:41 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4561 errors:0 dropped:0 overruns:0 frame:0 TX packets:4561 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:685425 (685.4 KB) TX bytes:685425 (685.4 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:213.206.63.44 P-t-P:213.206.34.4 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:53577 errors:0 dropped:0 overruns:0 frame:0 TX packets:58892 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:43667387 (43.6 MB) TX bytes:7504776 (7.5 MB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:5.5.117.43 P-t-P:5.5.117.43 Mask:255.255.0.0 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 00:27:19:f6:b5:cf inet addr:192.168.0.1 Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::227:19ff:fef6:b5cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12079 errors:0 dropped:0 overruns:0 frame:0 TX packets:11178 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1483691 (1.4 MB) TX bytes:4307899 (4.3 MB) So my question is - how to make OpenVPN redirect default gateway? Thanks!

    Read the article

  • Load-balancing between a Procurve switch and a server

    - by vlad
    Hello I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work? My setup is as follows: I have a central switch, a Procurve 2510G-24, image version Y.11.16. It's the center of a star topology, there are four switches connected to it via a single gigabit link. Those switches service the users. On the central switch, I have a server with two gigabit interfaces that I want to bond together in order to achieve higher throughput, and two other servers that have single gigabit connections to the switch. The topology looks as follows: sw1 sw2 sw3 sw4 | | | | --------------------- | sw0 | --------------------- || | | srv1 srv2 srv3 The servers were running FreeBSD 8.1. On srv1 I set up a lagg interface using the lacp protocol, and on the switch I set up a trunk for the two ports using lacp as well. The switch showed that the server was a lacp partner, I could ping the server from another computer, and the server could ping other computers. If I unplugged one of the cables, the connection would keep working, so everything looked fine. Until I tested throughput. There was only one link used between srv1 and sw0. All testing was conducted with iperf, and load distribution was checked with systat -ifstat. I was looking to test the load balancing for both receive and send operations, as I want this server to be a file server. There were therefore two scenarios: iperf -s on srv1 and iperf -c on the other servers iperf -s on the other servers and iperf -c on srv1 connected to all the other servers. Every time only one link was used. If one cable was unplugged, the connections would keep going. However, once the cable was plugged back in, the load was not distributed. Each and every server is able to fill the gigabit link. In one-to-one test scenarios, iperf was reporting around 940Mbps. The CPU usage was around 20%, which means that the servers could withstand a doubling of the throughput. srv1 is a dell poweredge sc1425 with onboard intel 82541GI nics (em driver on freebsd). After troubleshooting a previous problem with vlan tagging on top of a lagg interface, it turned out that the em could not support this. So I figured that maybe something else is wrong with the em drivers and / or lagg stack, so I started up backtrack 4r2 on this same server. So srv1 now uses linux kernel 2.6.35.8. I set up a bonding interface bond0. The kernel module was loaded with option mode=4 in order to get lacp. The switch was happy with the link, I could ping to and from the server. I could even put vlans on top of the bonding interface. However, only half the problem was solved: if I used srv1 as a client to the other servers, iperf was reporting around 940Mbps for each connection, and bwm-ng showed, of course, a nice distribution of the load between the two nics; if I run the iperf server on srv1 and tried to connect with the other servers, there was no load balancing. I thought that maybe I was out of luck and the hashes for the two mac addresses of the clients were the same, so I brought in two new servers and tested with the four of them at the same time, and still nothing changed. I tried disabling and reenabling one of the links, and all that happened was the traffic switched from one link to the other and back to the first again. I also tried setting the trunk to "plain trunk mode" on the switch, and experimented with other bonding modes (roundrobin, xor, alb, tlb) but I never saw any traffic distribution. One interesting thing, though: one of the four switches is a Cisco 2950, image version 12.1(22)EA7. It has 48 10/100 ports and 2 gigabit uplinks. I have a server (call it srv4) with a 4 channel trunk connected to it (4x100), FreeBSD 8.0 release. The switch is connected to sw0 via gigabit. If I set up an iperf server on one of the servers connected to sw0 and a client on srv4, ALL 4 links are used, and iperf reports around 330Mbps. systat -ifstat shows all four interfaces are used. The cisco port-channel uses src-mac to balance the load. The HP should use both the source and destination according to the manual, so it should work as well. Could this mean there is some bug in the HP firmware? Am I doing something wrong?

    Read the article

  • VSFTPD Unable to set write permissions on folder

    - by Frank Astin
    I've just set up my first FTP server with VSFTPD on cent os . I can connect to it fine using a user in the group ftp-users but I get read only access . I've tried several different CHMOD codes on the folder (even 777) all to no avail . This is the tutorial I used to set up the server http://tinyurl.com/73pyuxz hopefully you'll be able to see something I missed. Thanks in advance . Requested Config File : # Example config file /etc/vsftpd/vsftpd.conf # # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=NO # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. #anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. #anon_mkdir_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log #xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=YES # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # # You may fully customise the login banner string: #ftpd_banner=Welcome to blah FTP service. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). #chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd/chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. #ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd whith two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES

    Read the article

  • DHCP reply packets do not make it into KVM instance in OpenStack

    - by Lorin Hochstein
    I'm running a KVM instance inside of OpenStack, and it isn't getting an IP address from the DHCP server. Using tcpdump, I can see the request and reply packets on vnet0 of the compute host: # tcpdump -i vnet0 -n port 67 or port 68 tcpdump: WARNING: vnet0: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on vnet0, link-type EN10MB (Ethernet), capture size 65535 bytes 19:44:56.176727 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:46:f6:11, length 300 19:44:56.176785 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:46:f6:11, length 300 19:44:56.177315 IP 10.40.0.1.67 > 10.40.0.3.68: BOOTP/DHCP, Reply, length 319 19:45:02.179834 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:46:f6:11, length 300 19:45:02.179904 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:46:f6:11, length 300 19:45:02.180375 IP 10.40.0.1.67 > 10.40.0.3.68: BOOTP/DHCP, Reply, length 319 However, if I do the same thing on eth0 inside the KVM instance, I only see the request packets, not the reply packets. What would prevent the packets from making it from vnet0 of the host to eth0 of the guest? My host is running Ubuntu 12.04 and my guest is running CentOS 6.3. Note that I have added this rule in my iptables, but it doesn't resolve the issue: -A POSTROUTING -p udp -m udp --dport 68 -j CHECKSUM --checksum-fill The instance corresponds to vnet0 and is connected via br100: # brctl show bridge name bridge id STP enabled interfaces br100 8000.54781a8605f2 no eth1 vnet0 vnet1 virbr0 8000.000000000000 yes Here's the full iptables-save: # Generated by iptables-save v1.4.12 on Tue Apr 2 19:47:27 2013 *nat :PREROUTING ACCEPT [8323:2553683] :INPUT ACCEPT [7993:2494942] :OUTPUT ACCEPT [6158:461050] :POSTROUTING ACCEPT [6455:511595] :nova-compute-OUTPUT - [0:0] :nova-compute-POSTROUTING - [0:0] :nova-compute-PREROUTING - [0:0] :nova-compute-float-snat - [0:0] :nova-compute-snat - [0:0] :nova-postrouting-bottom - [0:0] -A PREROUTING -j nova-compute-PREROUTING -A OUTPUT -j nova-compute-OUTPUT -A POSTROUTING -j nova-compute-POSTROUTING -A POSTROUTING -j nova-postrouting-bottom -A POSTROUTING -s 192.168.122.0/24 ! -d 192.168.122.0/24 -p tcp -j MASQUERADE --to-ports 1024-65535 -A POSTROUTING -s 192.168.122.0/24 ! -d 192.168.122.0/24 -p udp -j MASQUERADE --to-ports 1024-65535 -A POSTROUTING -s 192.168.122.0/24 ! -d 192.168.122.0/24 -j MASQUERADE -A nova-compute-snat -j nova-compute-float-snat -A nova-postrouting-bottom -j nova-compute-snat COMMIT # Completed on Tue Apr 2 19:47:27 2013 # Generated by iptables-save v1.4.12 on Tue Apr 2 19:47:27 2013 *mangle :PREROUTING ACCEPT [7969:5385812] :INPUT ACCEPT [7905:5363718] :FORWARD ACCEPT [158:48190] :OUTPUT ACCEPT [6877:8647975] :POSTROUTING ACCEPT [7035:8696165] -A POSTROUTING -o virbr0 -p udp -m udp --dport 68 -j CHECKSUM --checksum-fill -A POSTROUTING -p udp -m udp --dport 68 -j CHECKSUM --checksum-fill COMMIT # Completed on Tue Apr 2 19:47:27 2013 # Generated by iptables-save v1.4.12 on Tue Apr 2 19:47:27 2013 *filter :INPUT ACCEPT [2196774:15856921923] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [2447201:1170227646] :nova-compute-FORWARD - [0:0] :nova-compute-INPUT - [0:0] :nova-compute-OUTPUT - [0:0] :nova-compute-inst-19 - [0:0] :nova-compute-inst-20 - [0:0] :nova-compute-local - [0:0] :nova-compute-provider - [0:0] :nova-compute-sg-fallback - [0:0] :nova-filter-top - [0:0] -A INPUT -j nova-compute-INPUT -A INPUT -i virbr0 -p udp -m udp --dport 53 -j ACCEPT -A INPUT -i virbr0 -p tcp -m tcp --dport 53 -j ACCEPT -A INPUT -i virbr0 -p udp -m udp --dport 67 -j ACCEPT -A INPUT -i virbr0 -p tcp -m tcp --dport 67 -j ACCEPT -A FORWARD -j nova-filter-top -A FORWARD -j nova-compute-FORWARD -A FORWARD -d 192.168.122.0/24 -o virbr0 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -s 192.168.122.0/24 -i virbr0 -j ACCEPT -A FORWARD -i virbr0 -o virbr0 -j ACCEPT -A FORWARD -o virbr0 -j REJECT --reject-with icmp-port-unreachable -A FORWARD -i virbr0 -j REJECT --reject-with icmp-port-unreachable -A OUTPUT -j nova-filter-top -A OUTPUT -j nova-compute-OUTPUT -A nova-compute-FORWARD -i br100 -j ACCEPT -A nova-compute-FORWARD -o br100 -j ACCEPT -A nova-compute-inst-19 -m state --state INVALID -j DROP -A nova-compute-inst-19 -m state --state RELATED,ESTABLISHED -j ACCEPT -A nova-compute-inst-19 -j nova-compute-provider -A nova-compute-inst-19 -s 10.40.0.1/32 -p udp -m udp --sport 67 --dport 68 -j ACCEPT -A nova-compute-inst-19 -s 10.40.0.0/16 -j ACCEPT -A nova-compute-inst-19 -p tcp -m tcp --dport 22 -j ACCEPT -A nova-compute-inst-19 -p icmp -j ACCEPT -A nova-compute-inst-19 -j nova-compute-sg-fallback -A nova-compute-inst-20 -m state --state INVALID -j DROP -A nova-compute-inst-20 -m state --state RELATED,ESTABLISHED -j ACCEPT -A nova-compute-inst-20 -j nova-compute-provider -A nova-compute-inst-20 -s 10.40.0.1/32 -p udp -m udp --sport 67 --dport 68 -j ACCEPT -A nova-compute-inst-20 -s 10.40.0.0/16 -j ACCEPT -A nova-compute-inst-20 -p tcp -m tcp --dport 22 -j ACCEPT -A nova-compute-inst-20 -p icmp -j ACCEPT -A nova-compute-inst-20 -j nova-compute-sg-fallback -A nova-compute-local -d 10.40.0.3/32 -j nova-compute-inst-19 -A nova-compute-local -d 10.40.0.4/32 -j nova-compute-inst-20 -A nova-compute-sg-fallback -j DROP -A nova-filter-top -j nova-compute-local COMMIT # Completed on Tue Apr 2 19:47:27 2013

    Read the article

  • vsftpd not allowing uploads. 550 response

    - by Josh
    I've set vsftpd up on a centos box. I keep trying to upload files but I keep getting "550 Failed to change directory" and "550 Could not get file size." Here's my vsftpd.conf # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=YES # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. anon_mkdir_write_enable=YES anon_other_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log #xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=NO # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # # You may fully customise the login banner string: #ftpd_banner=Welcome to blah FTP service. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). #chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd/chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. #ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd whith two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES log_ftp_protocol=YES banner_file=/etc/vsftpd/issue local_root=/var/www guest_enable=YES guest_username=ftpusr ftp_username=nobody

    Read the article

  • Centos 6.3 vsftp unable to upload file to apache webserver

    - by user148648
    I am new to Centos, I did work with Sun Solaris and upload files to Apache web server before. I create an end user account and manage to ftp using command prompt to the server, error message is '226 Transfer Done (but failed to open directory). Content of my vsftpd.conf as below # Example config file /etc/vsftpd/vsftpd.conf # # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=YES # ** may need to comment it back # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) #local_umask=022 local_umask=077 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. anon_upload_enable=YES # *** maybe to comment it back!!! # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. anon_mkdir_write_enable=YES # ** may need to comment it back!!! # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=YES # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. ascii_upload_enable=YES ascii_download_enable=YES # # You may fully customise the login banner string: ftpd_banner=Warning, only for authorize login. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). chroot_local_user=YES chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd/chroot_list local_root=/var/www # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd with two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES

    Read the article

  • CD/DVD burn error in ImgBurn and Nero

    - by bobby
    I am getting the errors shown below when I try to burn a CD/DVD on my DVD writer. I am seeing this error for every CD/DVD I try to burn. I am not able to write any CDs or DVDs using ImgBurn. The burn log below is a failed burn in Nero. What could be causing this error? Nero Burning ROM bobby 4C85-200E-4005-0004-0000-7660-0800-35X3-0000-407M-MX37-**** (*) Windows XP 6.1 IA32 WinAspi: - NT-SPTI used Nero Version: 7.11.3. Internal Version: 7, 11, 3, (Nero Express) Recorder: <HL-DT-ST DVDRAM GSA-H12N> Version: UL01 - HA 1 TA 1 - 7.11.3.0 Adapter driver: <IDE> HA 1 Drive buffer : 2048kB Bus Type : default CD-ROM: <ATAPI-CD ROM-DRIVE-52MAX > Version: 52PP - HA 1 TA 0 - 7.11.3.0 Adapter driver: <IDE> HA 1 === Scsi-Device-Map === === CDRom-Device-Map === ATAPI-CD ROM-DRIVE-52MAX F: CdRom0 HL-DT-ST DVDRAM GSA-H12N G: CdRom1 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte BUFE : 0 Physical memory : 958MB (981560kB) Free physical memory: 309MB (317024kB) Memory in use : 67 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 11.6.2010 CD Image 10:43:02 AM #1 Text 0 File SCSIPTICommands.cpp, Line 450 LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL 10:43:02 AM #2 Text 0 File Burncd.cpp, Line 3186 HL-DT-ST DVDRAM GSA-H12N Buffer underrun protection activated 10:43:02 AM #3 Text 0 File Burncd.cpp, Line 3500 Turn on Disc-At-Once, using CD-R/RW media 10:43:02 AM #4 Text 0 File DlgWaitCD.cpp, Line 307 Last possible write address on media: 359848 ( 79:59.73) Last address to be written: 318783 ( 70:52.33) 10:43:02 AM #5 Text 0 File DlgWaitCD.cpp, Line 319 Write in overburning mode: NO (enabled: CD) 10:43:02 AM #6 Text 0 File DlgWaitCD.cpp, Line 2988 Recorder: HL-DT-ST DVDRAM G SA-H12N; CDR co de: 00 97 27 18; O SJ entry from: Pla smon Data systems Ltd. ATIP Data: Special Info [hex] 1: D0 00 A0, 2: 61 1B 12 (LI 97:27.18), 3: 4F 3B 4A ( LO 79:59.74) Additional Info [hex] 1: 00 00 00 (invalid), 2: 00 00 00 (invalid), 3: 00 0 0 00 (invalid) 10:43:02 AM #7 Text 0 File DlgWaitCD.cpp, Line 493 >>> Protocol of DlgWaitCD activities: <<< ========================================= 10:43:02 AM #8 Text 0 File ThreadedTransferInterface.cpp, Line 785 Nero Report 1 Nero Burning ROM Setup items (after recorder preparation) 0: TRM_DATA_MODE1 (2 - CD-ROM Mode 1, Joliet) 2 indices, index0 (150) not provided original disc pos #0 + 318784 (318784) = #318784/70:50.34 not relocatable, disc pos for caching/writing not required/not required -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 318784 blocks [G: HL-DT-ST DVDRAM GSA-H12N] -------------------------------------------------------------- 10:43:02 AM #9 Text 0 File ThreadedTransferInterface.cpp, Line 986 Prepare [G: HL-DT-ST DVDRAM GSA-H12N] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Se ssion Clo sed, disc fixated Tracks 1 to 1: Idx 0 Idx 1 Next T rk 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 6531768 32, ISRC "" DAO layout: =========== ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________ -150 | lead-in | 0 | 0x41 | 0 | 0 | 0x00 -150 | 1 | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 1 | 0x41 | 318784 | 318784 | 0x00 318784 | lead-out | 1 | 0x41 | 0 | 0 | 0x00 10:43:02 AM #10 Text 0 File SCSIPTICommands.cpp, Line 240 SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME 10:43:02 AM #11 Text 0 File Burncd.cpp, Line 4286 Caching options: cache CDRom or Network-Yes, small files-Yes (<64KB) 10:43:02 AM #12 Phase 24 File dlgbrnst.cpp, Line 1767 Caching of files started 10:43:02 AM #13 Text 0 File Burncd.cpp, Line 4405 Cache writing successful. 10:43:02 AM #14 Phase 25 File dlgbrnst.cpp, Line 1767 Caching of files completed 10:43:02 AM #15 Phase 36 File dlgbrnst.cpp, Line 1767 Burn process started at 48x (7,200 KB/s) 10:43:02 AM #16 Text 0 File ThreadedTransferInterface.cpp, Line 2733 Verifying disc position of item 0 (not relocatable, no disc pos, no patch infos, orig at #0): write at #0 10:43:02 AM #17 Text 0 File MMC.cpp, Line 17806 StartDAO : CD-Text - Off 10:43:02 AM #18 Text 0 File MMC.cpp, Line 22488 Set BUFE: Buffer underrun protection -> ON 10:43:03 AM #19 Text 0 File MMC.cpp, Line 18034 CueData, Len=32 41 00 00 14 00 00 00 00 41 01 00 10 00 00 00 00 41 01 01 10 00 00 02 00 41 aa 01 14 00 46 34 22 10:43:03 AM #20 Text 0 File ThreadedTransfer.cpp, Line 268 Pipe memory size 83836800 10:43:16 AM #21 Text 0 File Cdrdrv.cpp, Line 1405 10:43:16.806 - G: HL-DT-ST DVDRAM GSA-H12N : Queue again later 10:43:42 AM #22 SPTI -1502 File SCSIPassThrough.cpp, Line 181 CdRom1: SCSIStatus(x02) WinError(0) NeroError(-1502) Sense Key: 0x04 (KEY_HARDWARE_ERROR) Nero Report 2 Nero Burning ROM Sense Code: 0x08 Sense Qual: 0x03 CDB Data: 0x2A 00 00 00 4D 00 00 00 20 00 00 00 Sense Area: 0x70 00 04 00 00 00 00 10 53 29 A1 80 08 03 Buffer x0c7d9a40: Len x10000 0xDC 87 EB 41 6E AC 61 5A 07 B2 DB 78 B5 D4 D9 24 0x8D BC 51 38 46 56 0F EE 16 15 5C 5B E3 B0 10 16 0x14 B1 C3 6E 30 2B C4 78 15 AB D5 92 09 B7 81 23 10:43:42 AM #23 CDR -1502 File Writer.cpp, Line 306 DMA-driver error, CRC error G: HL-DT-ST DVDRAM GSA-H12N 10:43:55 AM #24 Phase 38 File dlgbrnst.cpp, Line 1767 Burn process failed at 48x (7,200 KB/s) 10:43:55 AM #25 Text 0 File SCSIPTICommands.cpp, Line 287 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 10:44:01 AM #26 Text 0 File Cdrdrv.cpp, Line 11412 DriveLocker: UnLockVolume completed 10:44:01 AM #27 Text 0 File SCSIPTICommands.cpp, Line 450 UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL Existing drivers: Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon Nero Report 3

    Read the article

  • Spotlight Infinite Indexing issue (external data drive)

    - by Manca Weeks
    This is an external drive, formerly a boot drive which is now in use only to access music files (sibelius, audio, midi, live, logic etc.) without transferring the data into a new boot system, partly because of the issue I am about to describe, but mostly because the majority of the data is mainly there for archival purposes. The user is a composer and prominent musician and needs to be able to rehash the data at will. I have tried several things - here is a list: - make complete filesystem clone with antonio diaz's ddrescue - run Disk Warrior on copy, repair whatever errors occurred - wipe out all ACLs on entire drive - set all permissions to the same value - wide open 777 - remove any system data (applications, system files, including hidden files to the best of my knowledge) by selecting only non-system/app data and using Carbon Copy Cloner to put only the data of interest onto a newly formatted drive - transfer data to newly formatted drive folder by folder, resetting the spotlight index in between adding each to observe for issues (interesting here is that no issues occurred except for in Documents folder - when I transferred only the Documents folder to a newly formatted drive on its own - no trouble. It appears almost as thought it may not be the content but the quantity or specific combination of data that results in problems) - use DataRescue to transfer the data to yet another newly formatted drive to expose any missed hidden files Between each of the above steps I stopped Spotlight (search for anything beginning with md in Activity Monitor - All Processes and quitting it), deleted the .Spotlight-V100 directory from the affected drive. Restart Splotlight indexing by adding drive to Spotlight privacy list and removing it. In each case the same issue occurs - Spotlight begins indexing normally (or so it seems), then the index estimated time increases, usually to 4 hours remaining. This is where it gets stuck and continues to predict 4 hours remaining but never finishes. Sometimes I can't eject the drive and have to quit the md.. processes from Activity Monitor to be able to eject the drive without Force Eject. Once I disconnect the drive after the 4 hours remaining situation - if I reattach it, Spotlight forever estimates remaining time and never gets going again. So there it is. It is apparently not a filesystem issue, not a permissions issue and not tied to any particular piece of hardware or protocol (used USB and FW drives). I have tried this on several machines (3 to be precise) and in 10.5.8 and 10.6.5. Simply disabling Spotlight on this volume is not an option because the owner has no clue where things are as the data on the volume dates back to music projects and compositions from 2003 and before. He needs to be able to query for results. Anyone got any ideas? ---update 2-6-11 Since I have not received any responses except the one below which appears to misunderstand my point, I am updating this post hoping to get more responses. I have used the terminal command sudo opensnoop -p PID where PID is the mdworker process ID to try and determine what Spotlight is doing and hopefully find the files it's having trouble with. Here's what happens: After indexing for a few hours, mdworker is gone. It no longer shows up in Activity Monitor under "All Processes" and the Terminal window with the opensnoop result stops moving. I then proceeded to execute the same command on mds to see what it was doing and here's what I get, repeatedly: 501 57 mds 21 / 501 57 mds 21 /Volumes/Sno Leppard 501 57 mds 21 /Volumes/Tiger 501 57 mds 21 /Volumes/Leppard 501 57 mds 21 /Volumes/Disk Warrior 501 57 mds 21 /Volumes/ONM Data These represent all the volumes currently mounted in the system. All except ONM Data, which is the one I am trying to index, are excluded from SPotlight indexing at the moment. The sequence above repeats over and over, with slight variation, sometimes skipping one of the volumes. Questions - what happened to mdworker? What is mds doing? I will let this run until tomorrow morning and throughout the day and monitor for any changes. Any input would be very much appreciated. Even if you're not sure what the ultimate answer is, please alert me to anything you think I may be missing. Hopefully at some point we will figure this out... Thanks, M __final edit__ I finally resolved the issue and here is how I did it. I used the terminal command "sudo opensnoop -p PID" where the PID is the process id of the processes I was monitoring. I was looking at all instances of mds and mdworker running in the system. After the third time through indexing the same data set (see info above), I contacted Apple and got to their highest level of support - they were flabbergasted as well. They advised me to install yet another default 10.6.6 system and try again. The same pattern repeated - mds and mdworker(s) would start indexing and eventually the spotlight icon would say 6 hours remaining and all mdworkers were gone, mds at 90% or so of CPU. But I did finally figure out that the first time mdworker stopped like that, the last file it touched was always in the same folder. I excluded that folder from spotlight search and the rest of the data set indexed within about 2 hours with no strange behavior or failures. I copied that folder to another machine and Spotlight barfed immediately. Exclude that folder and all is well again. I have no clue what is causing this behavior, still, but I did find a functional solution to the problem. Anyone with a similar problem - run opensnoop on all instances of mds and mdworker and wait patiently for wdworker to exit. Look at the last file it touched and exclude the enclosing folder from being indexed. I was able to repeat the issue and solution on 2 different installs and 2 different copies of the data set. Hope this helps. If we find an actual cause of the folder being such a problem (it is called MICHAEL BRECKER RECORD SOLOS and contains almost 1 GB of audio related files - performer, live, SD2 - things like that), I will edit again to let you all know. Thanks for ay attempts to help, M

    Read the article

  • What is Causing this IIS 7 Web Service Sporadic Connectivity Error?

    - by dpalau
    On sporadic occasions we receive the following error when attempting to call an .asmx web service from a .Net client application: "The underlying connection was closed: A connection that was expected to be kept alive was closed by the server. Unable to read data from the transport connection: An existing connection was forcibly closed by the remote host." By sporadic I mean that it might occur zero, once every few days, or a half-dozen times a day for some users. It will never occur for the first web service call of a user. And the subsequent (usually the same) call will always work immediately after the failure. The failures happen across a variety of methods in the service and usually happens between 15-20 seconds (according to the log) from the time of the request. Looking in the IIS site log for the particular call will show one or the other of the following windows error codes: 121: The semaphore timeout period has elapsed. 1236: The network connection was aborted by the local system. Some additional environment details: Running on internal network web farm consisting of two servers running IIS7 on Windows Server 2008 OS. These problems did not occur when running in an older IIS6 web farm of three servers running on Windows Server 2003 (and we use a single IIS6/2003 instance for our development and staging environments with no issues). EDIT: Also, all of these server instances are VMWare virtual machines, not sure if that is a surprise anymore or not. The web service is a .Net 2.0/3.5 compiled .asmx web service that has its own application pool (.Net 2.0, integrated pipeline). Only has Windows Authentication enabled. We have another web service on the farm that uses the same physical path as the primary service, the only difference being that Basic Authentication is enabled. This is used for a portion of our ERP system. Have tried using the same and different application pool - no effect on the error. This site isn't hit as often as the primary site and has never had an error. As mentioned, the error will only happen when called from the .Net client - not from other applications. The client application is always creating a new web service object for each request and setting the service credentials to System.Net.CredentialCache.DefaultCredentials. The application is either deployed locally to a client or run in a Citrix server session. Those users running in Citrix doesn't seem to experience the issue, only locally deployed clients. The Citrix servers and the web farm are located in the same physical location and are located in the same IP range (10.67.xx.xx). Locally deployed clients experiencing the error are located elsewhere (10.105.xx.xx, 10.31.xx.xx). I've checked the OS logs to see if I can see any problems but nothing really sticks out. EDIT: Actually, I myself just ran into the error a little bit ago. I decided to check out the logs again and saw that there was a Security log entry of "Audit Failure" at the 'same' time (IIS log entry at 1:39:59, event log entry at 1:39:50). Not sure if this is a coincidence or not, I'll have to check out the logs of previous errors. I'm probably grasping for straws but the details: Log Name: Security Source: Microsoft-Windows-Security-Auditing Date: 7/8/2009 1:39:50 PM Event ID: 5159 Task Category: Filtering Platform Connection Level: Information Keywords: Audit Failure User: N/A Computer: is071019.<**.net Description: The Windows Filtering Platform has blocked a bind to a local port. Application Information: Process ID: 1260 Application Name: \device\harddiskvolume1\windows\system32\svchost.exe Network Information: Source Address: 0.0.0.0 Source Port: 54802 Protocol: 17 Filter Information: Filter Run-Time ID: 0 Layer Name: Resource Assignment Layer Run-Time ID: 36 I've also tried to use Failed Request Tracing in IIS7 but the service call never actually gets to where FRT can capture it (even though the failure is logged in the web service log). The network infrastructure group said they checked out the DNS and any NIC settings are correct so there is no 'flapping'. Everything pans out. I'm not sure that they checked out any domain controller servers though to see if that could be an issue. Any ideas? Or any other debugging strategies to get to the bottom of this? I'm just the developer in charge of the software and don't really have the knowledge on what to investigate from the networking side of things - although it does sound like a networking issue to me based on what is happening. Thanks in advance for any help.

    Read the article

  • Linux policy routing - packets not coming back

    - by Bugsik
    i am trying to set up policy routing on my home server. My network looks like this: Host routed VPN gateway Internet link through VPN 192.168.0.35/24 ---> 192.168.0.5/24 ---> 192.168.0.1 DSL router 10.200.2.235/22 .... .... 10.200.0.1 VPN server The traffic from 192.168.0.32/27 should be and is routed through VPN. I wanted to define some routing policies to route some traffic from 192.168.0.5 through VPN as well - for start - from user with uid 2000. Policy routing is done using iptables mark target and ip rule fwmark. The problem: When connecting using user 2000 from 192.168.0.5 tcpdump shows outgoing packets, but nothing comes back. Traffic from 192.168.0.35 works fine (here I am not using fwmark but src policy). Here is my VPN gateway setup: # uname -a Linux placebo 3.2.0-34-generic #53-Ubuntu SMP Thu Nov 15 10:49:02 UTC 2012 i686 i686 i386 GNU/Linux # iptables -V iptables v1.4.12 # ip -V ip utility, iproute2-ss111117 IPtables rules (all policies in table filter are ACCEPT) # iptables -t mangle -nvL Chain PREROUTING (policy ACCEPT 770K packets, 314M bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 767K packets, 312M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 5520 packets, 1920K bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 782K packets, 901M bytes) pkts bytes target prot opt in out source destination 74 4707 MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner UID match 2000 MARK set 0x3 Chain POSTROUTING (policy ACCEPT 788K packets, 903M bytes) pkts bytes target prot opt in out source destination # iptables -t nat -nvL Chain PREROUTING (policy ACCEPT 996 packets, 51172 bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 7 packets, 432 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 1364 packets, 112K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 2302 packets, 160K bytes) pkts bytes target prot opt in out source destination 119 7588 MASQUERADE all -- * vpn 0.0.0.0/0 0.0.0.0/0 Routing: # ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master lan state UNKNOWN qlen 1000 link/ether 00:40:63:f9:c3:8f brd ff:ff:ff:ff:ff:ff valid_lft forever preferred_lft forever 3: lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:40:63:f9:c3:8f brd ff:ff:ff:ff:ff:ff inet 192.168.0.5/24 brd 192.168.0.255 scope global lan inet6 fe80::240:63ff:fef9:c38f/64 scope link valid_lft forever preferred_lft forever 4: vpn: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 100 link/none inet 10.200.2.235/22 brd 10.200.3.255 scope global vpn # ip rule show 0: from all lookup local 32764: from all fwmark 0x3 lookup VPN 32765: from 192.168.0.32/27 lookup VPN 32766: from all lookup main 32767: from all lookup default # ip route show table VPN default via 10.200.0.1 dev vpn 10.200.0.0/22 dev vpn proto kernel scope link src 10.200.2.235 192.168.0.0/24 dev lan proto kernel scope link src 192.168.0.5 # ip route show default via 192.168.0.1 dev lan metric 100 10.200.0.0/22 dev vpn proto kernel scope link src 10.200.2.235 192.168.0.0/24 dev lan proto kernel scope link src 192.168.0.5 TCP dump showing no traffic coming back when connection is made from 192.168.0.5 user 2000 # tcpdump -i vpn tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on vpn, link-type RAW (Raw IP), capture size 65535 bytes ### Traffic from user 2000 on 192.168.0.5 ### 10:19:05.629985 IP 10.200.2.235.37291 > 10.100-78-194.akamai.com.http: Flags [S], seq 2868799562, win 14600, options [mss 1460,sackOK,TS val 6887764 ecr 0,nop,wscale 4], length 0 10:19:21.678001 IP 10.200.2.235.37291 > 10.100-78-194.akamai.com.http: Flags [S], seq 2868799562, win 14600, options [mss 1460,sackOK,TS val 6891776 ecr 0,nop,wscale 4], length 0 ### Traffic from 192.168.0.35 ### 10:23:12.066174 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [S], seq 2294159276, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 557451322 ecr 0,sackOK,eol], length 0 10:23:12.265640 IP 10.100-78-194.akamai.com.http > 10.200.2.235.49247: Flags [S.], seq 2521908813, ack 2294159277, win 14480, options [mss 1367,sackOK,TS val 388565772 ecr 557451322,nop,wscale 1], length 0 10:23:12.276573 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [.], ack 1, win 8214, options [nop,nop,TS val 557451534 ecr 388565772], length 0 10:23:12.293030 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [P.], seq 1:480, ack 1, win 8214, options [nop,nop,TS val 557451552 ecr 388565772], length 479 10:23:12.574773 IP 10.100-78-194.akamai.com.http > 10.200.2.235.49247: Flags [.], ack 480, win 7776, options [nop,nop,TS val 388566081 ecr 557451552], length 0

    Read the article

  • Nginx + Haproxy + Thin + Rails - 503 Service Unavailable -

    - by Luca G. Soave
    I don't know how troubleshoot this. I get "503 Service Unavailable" http error for all "nginx upstreams" proxy passing calls to haproxy fast_thin and slow_thin ( server 127.0.0.1:3100 and server 127.0.0.1:3200 ), which loadbalance on 6 Thin servers ( 127.0.0.1:3000 .. 3005 ). Static files like /blog are currently fine. The falldown is: nginx on port 80 - haproxy on 3100 and 3200 - thin on 3000 .. 3005 and then Rails. Here it is /etc/nginx/nginx.conf : user nginx; worker_processes 2; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; sendfile on; tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; include /etc/nginx/conf.d/*.conf; } then /etc/nginx/conf.d/default.conf upstream fast_thin { server 127.0.0.1:3100; } upstream slow_thin { server 127.0.0.1:3200; } server { listen 80; server_name www.gitwatcher.com; rewrite ^/(.*) http://gitwatcher.com/$1 permanent; } server { listen 80; server_name gitwatcher.com; access_log /var/www/gitwatcher/log/access.log; error_log /var/www/gitwatcher/log/error.log; root /var/www/gitwatcher/public; # index index.html; location /about { proxy_pass http://fast_thin; break; } location /trends { proxy_pass http://slow_thin; break; } location /categories { proxy_pass http://slow_thin; break; } location /signout { proxy_pass http://slow_thin; break; } location /auth/github { proxy_pass http://slow_thin; break; } location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (-f $request_filename/index.html) { rewrite (.*) $1/index.html break; } if (-f $request_filename.html) { rewrite (.*) $1.html break; } if (!-f $request_filename) { proxy_pass http://slow_thin; break; } } } then haproxy config file /etc/haproxy/haproxy.cfg : global log 127.0.0.1 local0 log 127.0.0.1 local1 notice #log loghost local0 info maxconn 4096 #chroot /usr/share/haproxy user haproxy group haproxy daemon #debug #quiet nbproc 1 # number of processing cores defaults log global retries 3 maxconn 2000 contimeout 5000 mode http clitimeout 60000 # maximum inactivity time on the client side srvtimeout 30000 # maximum inactivity time on the server side timeout connect 4000 # maximum time to wait for a connection attempt to a server to succeed option httplog option dontlognull option redispatch option httpclose # disable keepalive (HAProxy does not yet support the HTTP keep-alive mode) option abortonclose # enable early dropping of aborted requests from pending queue option httpchk # enable HTTP protocol to check on servers health option forwardfor # enable insert of X-Forwarded-For headers balance roundrobin # each server is used in turns, according to assigned weight stats enable # enable web-stats at /haproxy?stats stats auth haproxy:pr0xystats # force HTTP Auth to view stats stats refresh 5s # refresh rate of stats page listen rails_proxy 127.0.0.1:3100 # - equal weights on all servers # - maxconn will queue requests at HAProxy if limit is reached # - minconn dynamically scales the connection concurrency (bound my maxconn) depending on size of HAProxy queue # - check health every 20000 microseconds server web1 127.0.0.1:3000 weight 1 minconn 3 maxconn 6 check inter 20000 server web1 127.0.0.1:3001 weight 1 minconn 3 maxconn 6 check inter 20000 server web1 127.0.0.1:3002 weight 1 minconn 3 maxconn 6 check inter 20000 listen slow_proxy 127.0.0.1:3200 # cluster for slow requests, lower the queues, check less frequently server slow1 127.0.0.1:3003 weight 1 minconn 1 maxconn 3 check inter 40000 server slow2 127.0.0.1:3004 weight 1 minconn 1 maxconn 3 check inter 40000 server slow3 127.0.0.1:3005 weight 1 minconn 1 maxconn 3 check inter 40000 and the Thin config file /etc/thin/gitwatcher.yml : --- chdir: /var/www/gitwatcher environment: production address: 0.0.0.0 port: 3000 timeout: 30 log: log/thin.log pid: tmp/pids/thin.pid max_conns: 1024 max_persistent_conns: 100 require: [] wait: 30 servers: 6 daemonize: true if I look into open listen ports, I got the following : root@fullness:/var/www/gitwatcher# lsof | grep TCP | egrep "nginx|haproxy|thin" nginx 834 root 8u IPv4 921 0t0 TCP *:http (LISTEN) nginx 835 nginx 8u IPv4 921 0t0 TCP *:http (LISTEN) nginx 837 nginx 8u IPv4 921 0t0 TCP *:http (LISTEN) haproxy 1908 haproxy 4u IPv4 11699 0t0 TCP localhost:3100 (LISTEN) haproxy 1908 haproxy 6u IPv4 11701 0t0 TCP localhost:3200 (LISTEN) root@fullness:/var/www/gitwatcher# iptables -L get me the following : Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:22222 ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT all -- anywhere anywhere DROP all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Any help ?

    Read the article

  • LDAP over SSL with an EFI Fiery printer

    - by austinian
    I've got a printer with a Fiery running 8e Release 2. I can authenticate users against AD using the LDAP configuration, but I can only get it to work if I don't use SSL/TLS, and only if I use SIMPLE authentication. Right now, it's authenticating using a fairly low-impact user, but it's also the only system on our network that's not using LDAPS. I can get AD info fine over LDAPS using ldp.exe from my machine, our firewall, our mail filter, our linux boxes, etc. The only problem child is the Fiery. I've added the LDAP server certificate as a trusted cert to the Fiery, but after I check the box for Secure Communication and change the port to 636, pressing Validate results in a dialog box coming up saying: LDAP Validation Failed Server Name invalid or server is unavailable. I've tried changing the server name to use just the name, the FQDN, and the IP address, and changed it to another server, just to see if it was just this AD server that was fussy with the Fiery. EDIT: removed LDP output, added packet capture analysis from wireshark: The conversation seems pretty normal to me, up to the point where the Fiery terminates the connection after the server sends back a handshake response. Maybe they messed up their TLS implementation? I'm trying support, but it's been fairly useless so far. The cert is a SHA-2 (sha256RSA) 2048-bit certificate. Also, it looks like the Fiery is specifying TLS 1.0. Looking at http://msdn.microsoft.com/en-us/library/windows/desktop/aa374757(v=vs.85).aspx, I'm not seeing SHA256 and TLS 1.0 combination being supported by SChannel. headdesk perhaps that's why, after the DC changes the cipher spec, the connection is terminated by the Fiery? TLS 1.1 and 1.2 are enabled on the DC. Wireshark conversation: DC: 172.17.2.22, Fiery: 172.17.2.42 No. Time Source Source Port Destination Destination Port Protocol Length Info 1 0.000000000 172.17.2.42 48633 172.17.2.22 ldaps TCP 74 48633 > ldaps [SYN] Seq=0 Win=5840 Len=0 MSS=1460 SACK_PERM=1 TSval=3101761 TSecr=0 WS=4 2 0.000182000 Dell_5e:94:e3 Broadcast ARP 60 Who has 172.17.2.42? Tell 172.17.2.22 3 0.000369000 TyanComp_c9:0f:90 Dell_5e:94:e3 ARP 60 172.17.2.42 is at 00:e0:81:c9:0f:90 4 0.000370000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 74 ldaps > 48633 [SYN, ACK] Seq=0 Ack=1 Win=8192 Len=0 MSS=1460 WS=256 SACK_PERM=1 TSval=67970573 TSecr=3101761 5 0.000548000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=1 Ack=1 Win=5840 Len=0 TSval=3101761 TSecr=67970573 6 0.001000000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 147 Client Hello 7 0.001326000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 1514 [TCP segment of a reassembled PDU] 8 0.001513000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 1514 [TCP segment of a reassembled PDU] 9 0.001515000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=82 Ack=1449 Win=8736 Len=0 TSval=3101761 TSecr=67970573 10 0.001516000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=82 Ack=2897 Win=11632 Len=0 TSval=3101761 TSecr=67970573 11 0.001732000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 1514 [TCP segment of a reassembled PDU] 12 0.001737000 172.17.2.22 ldaps 172.17.2.42 48633 TLSv1 1243 Server Hello, Certificate, Certificate Request, Server Hello Done 13 0.001738000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=82 Ack=4345 Win=14528 Len=0 TSval=3101761 TSecr=67970573 14 0.001739000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [ACK] Seq=82 Ack=5522 Win=17424 Len=0 TSval=3101761 TSecr=67970573 15 0.002906000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 78 Certificate 16 0.004155000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 333 Client Key Exchange 17 0.004338000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 66 ldaps > 48633 [ACK] Seq=5522 Ack=361 Win=66304 Len=0 TSval=67970573 TSecr=3101762 18 0.004338000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 72 Change Cipher Spec 19 0.005481000 172.17.2.42 48633 172.17.2.22 ldaps TLSv1 327 Encrypted Handshake Message 20 0.005645000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 66 ldaps > 48633 [ACK] Seq=5522 Ack=628 Win=66048 Len=0 TSval=67970574 TSecr=3101762 21 0.010247000 172.17.2.22 ldaps 172.17.2.42 48633 TLSv1 125 Change Cipher Spec, Encrypted Handshake Message 22 0.016451000 172.17.2.42 48633 172.17.2.22 ldaps TCP 66 48633 > ldaps [FIN, ACK] Seq=628 Ack=5581 Win=17424 Len=0 TSval=3101765 TSecr=67970574 23 0.016630000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 66 ldaps > 48633 [ACK] Seq=5581 Ack=629 Win=66048 Len=0 TSval=67970575 TSecr=3101765 24 0.016811000 172.17.2.22 ldaps 172.17.2.42 48633 TCP 60 ldaps > 48633 [RST, ACK] Seq=5581 Ack=629 Win=0 Len=0

    Read the article

  • vsftpd not allowing uploads. 550 response.

    - by Josh
    I've set vsftpd up on a centos box. I keep trying to upload files but I keep getting "550 Failed to change directory" and "550 Could not get file size." Here's my vsftpd.conf # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # Allow anonymous FTP? (Beware - allowed by default if you comment this out). anonymous_enable=YES # # Uncomment this to allow local users to log in. local_enable=YES # # Uncomment this to enable any form of FTP write command. write_enable=YES # # Default umask for local users is 077. You may wish to change this to 022, # if your users expect that (022 is used by most other ftpd's) local_umask=022 # # Uncomment this to allow the anonymous FTP user to upload files. This only # has an effect if the above global write enable is activated. Also, you will # obviously need to create a directory writable by the FTP user. anon_upload_enable=YES # # Uncomment this if you want the anonymous FTP user to be able to create # new directories. anon_mkdir_write_enable=YES anon_other_write_enable=YES # # Activate directory messages - messages given to remote users when they # go into a certain directory. dirmessage_enable=YES # # The target log file can be vsftpd_log_file or xferlog_file. # This depends on setting xferlog_std_format parameter xferlog_enable=YES # # Make sure PORT transfer connections originate from port 20 (ftp-data). connect_from_port_20=YES # # If you want, you can arrange for uploaded anonymous files to be owned by # a different user. Note! Using "root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # The name of log file when xferlog_enable=YES and xferlog_std_format=YES # WARNING - changing this filename affects /etc/logrotate.d/vsftpd.log #xferlog_file=/var/log/xferlog # # Switches between logging into vsftpd_log_file and xferlog_file files. # NO writes to vsftpd_log_file, YES to xferlog_file xferlog_std_format=NO # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # # You may fully customise the login banner string: #ftpd_banner=Welcome to blah FTP service. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd/banned_emails # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). #chroot_list_enable=YES # (default follows) #chroot_list_file=/etc/vsftpd/chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. #ls_recurse_enable=YES # # When "listen" directive is enabled, vsftpd runs in standalone mode and # listens on IPv4 sockets. This directive cannot be used in conjunction # with the listen_ipv6 directive. listen=YES # This directive enables listening on IPv6 sockets. To listen on IPv4 and IPv6 # sockets, you must run two copies of vsftpd whith two configuration files. # Make sure, that one of the listen options is commented !! #listen_ipv6=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES log_ftp_protocol=YES banner_file=/etc/vsftpd/issue local_root=/var/www guest_enable=YES guest_username=ftpusr ftp_username=nobody

    Read the article

  • Cisco ASA 5505 - L2TP over IPsec

    - by xraminx
    I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

    Read the article

  • Unable to find valid certification path to requested target while CAS authentication

    - by Dmitriy Sukharev
    I'm trying to configure CAS authentication. It requires both CAS and client application to use HTTPS protocol. Unfortunately we should use self-signed certificate (with CN that doesn't have anything in common with our server). Also the server is behind firewall and we have only two ports (ssh and https) visible. As far as there're several application that should be visible externally, we use Apache for ajp reverse proxying requests to these applications. Secure connections are managed by Apache, and all Tomcat are not configured to work with SSL. But I obtained exception while authentication, therefore desided to set keystore in CATALINA_OPTS: export CATALINA_OPTS="-Djavax.net.ssl.keyStore=/path/to/tomcat/ssl/cert.pfx -Djavax.net.ssl.keyStoreType=PKCS12 -Djavax.net.ssl.keyStorePassword=password -Djavax.net.ssl.keyAlias=alias -Djavax.net.debug=ssl" cert.pfx was obtained from certificate and key that are used by Apache HTTP Server: $ openssl pkcs12 -export -out /path/to/tomcat/ssl/cert.pfx -inkey /path/to/apache2/ssl/server-key.pem -in /path/to/apache2/ssl/server-cert.pem When I try to authenticate a user I obtain the following exception: Caused by: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target at sun.security.provider.certpath.SunCertPathBuilder.engineBuild(SunCertPathBuilder.java:174) ~[na:1.6.0_32] at java.security.cert.CertPathBuilder.build(CertPathBuilder.java:238) ~[na:1.6.0_32] at sun.security.validator.PKIXValidator.doBuild(PKIXValidator.java:318) ~[na:1.6.0_32] Meanwhile I can see in catalina.out that Tomcat see certificate in cert.pfx and it's the same as the one that is used while authentication: 09:11:38.886 [http-bio-8080-exec-2] DEBUG o.j.c.c.v.Cas20ProxyTicketValidator - Constructing validation url: https://external-ip/cas/proxyValidate?pgtUrl=https%3A%2F%2Fexternal-ip%2Fclient%2Fj_spring_cas_security_proxyreceptor&ticket=ST-17-PN26WtdsZqNmpUBS59RC-cas&service=https%3A%2F%2Fexternal-ip%2Fclient%2Fj_spring_cas_security_check 09:11:38.886 [http-bio-8080-exec-2] DEBUG o.j.c.c.v.Cas20ProxyTicketValidator - Retrieving response from server. keyStore is : /path/to/tomcat/ssl/cert.pfx keyStore type is : PKCS12 keyStore provider is : init keystore init keymanager of type SunX509 *** found key for : 1 chain [0] = [ [ Version: V1 Subject: CN=wrong.domain.name, O=Our organization, L=Location, ST=State, C=Country Signature Algorithm: SHA1withRSA, OID = 1.2.840.113549.1.1.5 Key: Sun RSA public key, 1024 bits modulus: 13??a lot of digits here??19 public exponent: ????7 Validity: [From: Tue Apr 24 16:32:18 CEST 2012, To: Wed Apr 24 16:32:18 CEST 2013] Issuer: CN=wrong.domain.name, O=Our organization, L=Location, ST=State, C=Country SerialNumber: [ d??????? ????????] ] Algorithm: [SHA1withRSA] Signature: 0000: 65 Signature is here 0070: 96 . ] *** trustStore is: /jdk-home-folder/jre/lib/security/cacerts Here is a lot of trusted CAs. Here is nothing related to our certicate or our (not trusted) CA. ... 09:11:39.731 [http-bio-8080-exec-4] DEBUG o.j.c.c.v.Cas20ProxyTicketValidator - Retrieving response from server. Allow unsafe renegotiation: false Allow legacy hello messages: true Is initial handshake: true Is secure renegotiation: false %% No cached client session *** ClientHello, TLSv1 RandomCookie: GMT: 1347433643 bytes = { 63, 239, 180, 32, 103, 140, 83, 7, 109, 149, 177, 80, 223, 79, 243, 244, 60, 191, 124, 139, 108, 5, 122, 238, 146, 1, 54, 218 } Session ID: {} Cipher Suites: [SSL_RSA_WITH_RC4_128_MD5, SSL_RSA_WITH_RC4_128_SHA, TLS_RSA_WITH_AES_128_CBC_SHA, TLS_DHE_RSA_WITH_AES_128_CBC_SHA, TLS_DHE_DSS_WITH_AES_128_CBC_SHA, SSL_RSA_WITH_3DES_EDE_CBC_SHA, SSL_DHE_RSA_WITH_3DES_EDE_CBC_SHA, SSL_DHE_DSS_WITH_3DES_EDE_CBC_SHA, SSL_RSA_WITH_DES_CBC_SHA, SSL_DHE_RSA_WITH_DES_CBC_SHA, SSL_DHE_DSS_WITH_DES_CBC_SHA, SSL_RSA_EXPORT_WITH_RC4_40_MD5, SSL_RSA_EXPORT_WITH_DES40_CBC_SHA, SSL_DHE_RSA_EXPORT_WITH_DES40_CBC_SHA, SSL_DHE_DSS_EXPORT_WITH_DES40_CBC_SHA, TLS_EMPTY_RENEGOTIATION_INFO_SCSV] Compression Methods: { 0 } *** http-bio-8080-exec-4, WRITE: TLSv1 Handshake, length = 75 http-bio-8080-exec-4, WRITE: SSLv2 client hello message, length = 101 http-bio-8080-exec-4, READ: TLSv1 Handshake, length = 81 *** ServerHello, TLSv1 RandomCookie: GMT: 1347433643 bytes = { 145, 237, 232, 63, 240, 104, 234, 201, 148, 235, 12, 222, 60, 75, 174, 0, 103, 38, 196, 181, 27, 226, 243, 61, 34, 7, 107, 72 } Session ID: {79, 202, 117, 79, 130, 216, 168, 38, 68, 29, 182, 82, 16, 25, 251, 66, 93, 108, 49, 133, 92, 108, 198, 23, 120, 120, 135, 151, 15, 13, 199, 87} Cipher Suite: SSL_RSA_WITH_RC4_128_SHA Compression Method: 0 Extension renegotiation_info, renegotiated_connection: <empty> *** %% Created: [Session-2, SSL_RSA_WITH_RC4_128_SHA] ** SSL_RSA_WITH_RC4_128_SHA http-bio-8080-exec-4, READ: TLSv1 Handshake, length = 609 *** Certificate chain chain [0] = [ [ Version: V1 Subject: CN=wrong.domain.name, O=Our organization, L=Location, ST=State, C=Country Signature Algorithm: SHA1withRSA, OID = 1.2.840.113549.1.1.5 Key: Sun RSA public key, 1024 bits modulus: 13??a lot of digits here??19 public exponent: ????7 Validity: [From: Tue Apr 24 16:32:18 CEST 2012, To: Wed Apr 24 16:32:18 CEST 2013] Issuer: CN=wrong.domain.name, O=Our organization, L=Location, ST=State, C=Country SerialNumber: [ d??????? ????????] ] Algorithm: [SHA1withRSA] Signature: 0000: 65 Signature is here 0070: 96 . ] *** http-bio-8080-exec-4, SEND TLSv1 ALERT: fatal, description = certificate_unknown http-bio-8080-exec-4, WRITE: TLSv1 Alert, length = 2 http-bio-8080-exec-4, called closeSocket() http-bio-8080-exec-4, handling exception: javax.net.ssl.SSLHandshakeException: sun.security.validator.ValidatorException: PKIX path building failed: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target I tried to convert our pem certificate to der format and imported it to trustedKeyStore (cacerts) (without private key), but it didn't change anything. But I'm not confident that I did it rigth. Also I must inform you that I don't know passphrase for our servier-key.pem file, and probably it differs from password for keystore created by me. OS: CentOS 6.2 Architecture: x64 Tomcat version: 7 Apache HTTP Server version: 2.4 Is there any way to make Tomcat accepts our certificate?

    Read the article

  • CISCO 2911 Router configuration

    - by bala
    Device cisco 2911 router configuration support is required please. I have exchange server 2010 configured and working without any errors the problem is in cisco router configuration when exchange server sends emails out the receives WAN IP not the public ip. I have configured RDNS lookups with our MX record IP addesses that match the FQDN but all our emails are rejected because it does not match with the public ip. Receiving mails problem is not an problem all mails are coming through. i am sure i am missing something on the router configuration that does not sends the public ip, can any one help me to solve this issue. Note; I've got 1 WAN IP & 8 Public IP from ISP . Find below the running configuration. Building configuration... Current configuration : 2734 bytes ! ! Last configuration change at 06:32:13 UTC Tue Apr 3 2012 ! NVRAM config last updated at 06:32:14 UTC Tue Apr 3 2012 ! NVRAM config last updated at 06:32:14 UTC Tue Apr 3 2012 version 15.1 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname BSBG-LL ! boot-start-marker boot-end-marker ! ! enable secret 5 $x$xHrxxxxx5ox0 enable password 7 xx23xx5FxxE1xx044 ! no aaa new-model ! no ipv6 cef ip source-route ip cef ! ! ! ! ! ip flow-cache timeout active 1 ip domain name yourdomain.com ip name-server 213.42.20.20 ip name-server 195.229.241.222 multilink bundle-name authenticated ! ! crypto pki token default removal timeout 0 ! ! license udi pid CISCO2911/K9 ! ! username bsbg ! ! ! ! ! ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 ip address 192.168.0.9 255.255.255.0 ip flow ingress ip nat inside ip virtual-reassembly in duplex auto speed 100 no cdp enable ! interface GigabitEthernet0/1 ip address 213.42.xx.x2 255.255.255.252 ip nat outside ip virtual-reassembly in duplex auto speed auto no cdp enable ! interface GigabitEthernet0/2 no ip address shutdown duplex auto speed auto ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip nat inside source list 120 interface GigabitEthernet0/1 overload ip nat inside source static tcp 192.168.0.4 25 94.56.89.100 25 extendable ip nat inside source static tcp 192.168.0.4 53 94.56.89.100 53 extendable ip nat inside source static udp 192.168.0.4 53 94.56.89.100 53 extendable ip nat inside source static tcp 192.168.0.4 110 94.56.89.100 110 extendable ip nat inside source static tcp 192.168.0.4 443 94.56.89.100 443 extendable ip nat inside source static tcp 192.168.0.4 587 94.56.89.100 587 extendable ip nat inside source static tcp 192.168.0.4 995 94.56.89.100 995 extendable ip nat inside source static tcp 192.168.0.4 3389 94.56.89.100 3389 extendable ip nat inside source static tcp 192.168.0.4 443 94.56.89.101 443 extendable ip nat inside source static tcp 192.168.0.12 80 94.56.89.102 80 extendable ip nat inside source static tcp 192.168.0.12 443 94.56.89.102 443 extendable ip nat inside source static tcp 192.168.0.12 3389 94.56.89.102 3389 extendable ip route 0.0.0.0 0.0.0.0 213.42.69.41 ! access-list 120 permit ip 192.168.0.0 0.0.0.255 any ! ! ! control-plane ! ! ! line con 0 exec-timeout 5 0 line aux 0 line 2 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line vty 0 4 password 7 xx64xxD530D26086Dxx login transport input all ! scheduler allocate 20000 1000 end

    Read the article

< Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >