Search Results

Search found 1039 results on 42 pages for 'jon mcintosh'.

Page 14/42 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

• Easiest way to move my Windows installation to an SSD?

  - by Jon Artus

  I've taken the plunge and bought an SSD and want to move my existing Windows installation over. The current hard disk is 500Gb, but I've trimmed the contents down to about ~40Gb. I'm transferring it across to a 100Gb SSD and looking for the easiest way just to copy everything across and set the SSD up as a boot device. I've looked at a few tools like Macrium Reflect, but they don't seem able to restore to a smaller drive. Do I need to go for something like PING to do this? I'm trying to avoid scary Linux-based boot utilities if possible, does anyone know of an easier way?

  Read the article

• Connecting a USB laptop to a RJ45 serial port

  - by Jon

  We are about to get our first managed switch at work (Procurve 2520G-24-PoE), and this lowly programmer gets to put on his admin hat and try to configure it. The switch has an RJ45 serial port for console access. My laptop has USB ports but no serial port. In fact, there isn't a single computer in the office with a serial port. I've seen USB-to-DB9 adapters, but I need to go from USB to RJ45 (serial). How would I go about accomplishing this? Do I need two adapters? Will USB-to-DB9 and then DB9-to-RJ45 work? Thanks in advance.

  Read the article

• Port forwarding with multiple IP's

  - by Jon

  I work at a company which uses a Fortigate 60 router, something I'm not really familiar with. Everything worked fine with it until a week ago when Comcast came in and replaced our modem. It seemed as though the process went smoothly - our connection came back up and our static IP remained the same. However, none of our port forwarding is working. What has me confused is the Comcast modem apparently has two IP addresses. The WAN2 interface for it in the Fortigate router is set to 10.1.10.10. However, all of our port forwarding settings are set to an external IP address of 10.1.10.50. Now this setup used to work fine, so something with the Comcast modem must have changed. How can I find out what? I tried setting a computer to a local IP of 10.1.10.15 so I could open up the web interface for the modem, but I can't even ping 10.1.10.10 when I do that. Any ideas? Thanks!

  Read the article

• How do private BitTorrent trackers monitor how much users upload/download?

  - by Jon-Eric

  From Wikipedia: Most private trackers monitor how much users upload or download, and in most situations, enforce a minimum upload-to-download ratio. How exactly can a tracker figure out how much data was uploaded and downloaded by each user? My understanding is that a BitTorrent tracker is merely a registry of users that are currently downloading/seeding and that peers, once connected, transfer data directly. So I wouldn't think that the tracker would know anything about the amount of data transferred, much less, where it came from.

  Read the article

• Technology mash: is this possible?

  - by Jon Story

  I'm in the process of setting up my own DNS+hosting on a couple of VPS and my home machines, mostly for academic/learning purposes, but also for convenient accessing of my files, hosting my personal websites, private git repositories etc. I've got a main web server with DNS, and a slave DNS server. I've also got a couple of machines at home doing file hosting, video streaming and all that fun stuff. I'm intending to use my VPS's to provide myself with a dynamic DNS system so that I can point mydomain.com at my DNS servers, with home.mydomain.com going into my home network via a raspberry pi. HOWEVER.... I've not got access to the network infrastructure at home (rented accommodation with managed internet), so I can't forward the ports on the router to my own machines. As such, I'm wondering if it's possible to route all the traffic via an SSH/HTTP tunnel through one of the VPS? My plan is to have the raspberry pi provide a VPN into my home network. The raspberry pi uses SSH to connect to the VPS, and the VPS forwards any traffic to home.mydomain.com via the tunnel to the raspberry pi. Is this even possible, and how do I go about it? I don't mind getting my hands dirty with coding and low level tools, I'm just not sure where to start or what the best way to go about it is.

  Read the article

• Ubuntu "No space left on device" for /home, df shows 100% full, ds shows much, much less

  - by Jon Cram

  On an Ubuntu 12.04 server, normal users can no longer create or add to files in /home, encountering a "No space left on device" error. The /home directory has a capacity of 1.7 terabytes and as far as I can tell is nowhere near full in terms of actual data stored or inodes used. df -h shows: Filesystem Size Used Avail Use% Mounted on /dev/md2 1.0T 18G 955G 2% / udev 7.7G 4.0K 7.7G 1% /dev tmpfs 3.1G 320K 3.1G 1% /run none 5.0M 0 5.0M 0% /run/lock none 7.7G 0 7.7G 0% /run/shm cgroup 7.7G 0 7.7G 0% /sys/fs/cgroup /dev/md3 1.7T 1.7T 0 100% /home /dev/md1 496M 45M 426M 10% /boot /home indeed looks rather full. du -hs /home suggests otherwise: 1.4G /home There appears no inode issue - df -i: Filesystem Inodes IUsed IFree IUse% Mounted on /dev/md2 67108864 75334 67033530 1% / udev 2013497 527 2012970 1% /dev tmpfs 2015816 440 2015376 1% /run none 2015816 2 2015814 1% /run/lock none 2015816 1 2015815 1% /run/shm cgroup 2015816 9 2015807 1% /sys/fs/cgroup /dev/md3 113909760 105981 113803779 1% /home /dev/md1 131072 239 130833 1% /boot I recently deleted a many gigabytes of application cache and log data from /home, however this was in the tens of gigabytes at best and nowhere near the capcity of /home. Update 1: du -hs --apparent-size /home 1.2G /home du -hs /home 1.4G /home What might be going on here?

  Read the article

• How can I make a VB script execute every time Windows starts up?

  - by jon

  My goal is to copy INI.file each time Windows XP is started up or rebooted. The following VB script copies INI.file from a local directory to C:\INI_DIR. I tried to copy the VB script to C:\WINDOWS\system32\config\systemprofile\Start Menu\Programs\Startup, but it doesn't get activated. Is it not the right path? How can I make it execute on startup/reboot? The script: Dim currDir Const OverwriteExisting = True Set fso = CreateObject("Scripting.FileSystemObject") currDir = fso.GetParentFolderName(Wscript.ScriptFullName) Set objFSO = CreateObject("Scripting.FileSystemObject") objFSO.CopyFile currDir & "\INI.file" , "C:\INI_DIR" , OverwriteExisting ' Release the objFSO objects Set objFSO = Nothing ' Release the fso objects Set fso = Nothing

  Read the article

• Is there still a place for tape storage?

  - by Jon Ericson

  We've backed up our data on LTO tapes for years and it's a real comfort to know we have everything on tape. A sister project and one of our data providers have both moved to 100% disk storage because the cost of disk has dropped so much. When we propose systems to potential customers these days we tend to downplay or not mention our use of tape systems for data storage since it might seem outdated. I feel more comfortable with having data saved in two separate formats: disks and tape. In addition, once data is securely written to tape, I feel (perhaps naively) that it's been permanently saved. Not having to rely on a RAID controller to be able to read back data is another plus for me. Do you see a place for tape backup these days?

  Read the article

• How does one delete a directory filled with files and other subdirectory permanently, bypassing the trash, from the command line in OS X?

  - by Jon

  So my command line skills are a little rusty and I'm having trouble remembering the differences between the meanings of flags in different distro's os's. I also don't really remember all my technical lingo so manpages seem really unclear. Basically I'm on Mac OS X and want to delete a directory along with all of its contents. What I'm mainly concerned about, I suppose, is that it'll delete literally ALL of the references within the directory, including ../ and ../<everything else, including ../'s own ../> and then just totally screw up my entire system. Which of these do I want to run? $ rm -R dir-name/ or $ rm -r

  Read the article

• OS X Terminal ends session at opening : permission denied

  - by Jon

  I have an issue with Terminal on MacOS X 10.7.4. I know where it comes from, but I don't know how to solve it : Yesterday, I installed fish-shell as a shell replacement. Following the installation instructions, I ended typing the following command : chsh -s /usr/local/bin/fish I noticed I had to do a : sudo bash for it to work. Once done, I quit. Today, I try to run Terminal and I see te following message : Last login: Wed Jun 27 12:38:01 on ttys000 login: /usr/local/bin/fish: Permission denied [Opération terminée] (yes, I'm French, which explains my poor English). I cannot type any command since I have no access to the Terminal. I tried with iTerm2 but same issue. No command is set at launch in the default profile of Terminal/iTerm2 (well, in the UI). How can I take the power back ? Thank you.

  Read the article

• RDP session re-locks right after login

  - by Jon Bailey

  For some reason, after users do the initial authentication, the system logs in (or unlocks) and locks the screen again within a few seconds (without dropping the RDP session). I've seen this on XP SP3 and Server 2k3. Clients are both major versions of the MS client, and rdesktop. Update: We've seen the issue on a range of machines from 2k3 server (no logon/post logon scripts on servers) to XP SP3. Multiple machines have the same issue - even coming from a fresh and fully patched install.

  Read the article

• How to override puppet class arguments in child node?

  - by Jon Skarpeteig

  I'm attempting to accomplish something like the below: node 'basenode' { class { 'puppet' : disable => false, } } node 'child' inherits 'basenode' { class { 'puppet' : disable => true, } } This gives me: err: Could not retrieve catalog from remote server: Error 400 on SERVER: Duplicate definition: Class[Puppet] is already defined How can I override this setting for this single node, and still have a parameterised class?

  Read the article

• Pivot Table grand total across columns

  - by Jon

  I'm using Excel 2010 and Power Pivot. I'm trying to calculate confidence and velocity for a development team. I'm extracting some information from our time and defect system each day and building a data set. What I need to do with Excel is do the calculations. So each day I add to my data set 1 row per task in the current project, estimate for that task and the time spent on that task. What I want to calculate is the estimate/actual for each task but also for each person. The trouble is that each day the actual is cumulative so I need to pick out the maximum value for each task. The estimate should remain unchanged. I can make this work at the task level with a calculated measure (=MAX(worked)/MAX(estimate)) but I don't know how to total this up for a person. I need the sum of the max worked for each task. So a dataset might look like: Name Task Estimate Worked N1 T1 3 1 N2 T2 3 1 N3 T3 4 1 N1 T1 3 2 N2 T4 5 1 N3 T3 4 2 N1 T5 1 2 N2 T6 2 3 N3 T7 3 2 What I want to see is for task T1 2 days were worked against an estimate of 3 days - so 2/3. For person N1 I want to see that they worked a total of 4 days against an estimate of 4 days so 4/4. For person N2 they worked 5 days for an estimate of 10 days. Any ideas on how I can achieve this?

  Read the article

• How do I replace a harddrive that is in a two-way mirror storage space on Windows 8?

  - by Jon

  I have a storage space in Windows 8 doing a two-way mirror on three harddrives. The sizes are 297GB, 189GB, and 70GB. I would like to replace the 70GB HD with a larger one. My thought was to remove that drive from the space via the Storage Space control panel, shutdown, replace HD with bigger drive, reboot, add new HD to the storage space. I can't find any options to remove a HD from a storage space in the control panel. Should I just shutdown and swap out the small drive or is there another process for safely replacing the old HD? (By the way, the old HD is still operational.)

  Read the article

• SQL Server database filled the hard drive and freeing up space isn't possible

  - by Jon

  I have a database in SQL Server 2008 on a 1Tb hard drive and it filled the drive, there is only 4Kb free. The MDF file is 323Gb and the LDF is 653Gb. The hard disk this DB is on has no other files on it other than the MDF and LDF so it's impossible to free up any space on the drive. The main hard disk is smaller but there is enough room to transfer the MDF to that drive, in case that helps. This server is overseas at a customer site and it's not possible at the moment to add more disk space to the server. It's also not possible to delete any records because the DB is in a failed mode (due to no disk space) and it doesn't respond to most commands. The Db is currently in full recovery mode which is why the LDF file is so large. This DB really doesn't need to be in full recovery so going forward we plan on switching it to simple mode which will save us a lot of space. I also don't care about losing the LDF file, but I need all of the data. I've spent a lot of time looking for a way out of this problem but everything I've found first involves either freeing up disk space or adding more disk space, neither of which is an option at this time. I'm stuck and any help would be greatly appreciated. I get the following log when trying to switch the DB to online mode. Msg 945, Level 14, State 2, Line 3 Database 'DBNAME' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. Msg 5069, Level 16, State 1, Line 3 ALTER DATABASE statement failed. Msg 1101, Level 17, State 12, Line 3 Could not allocate a new page for database 'DBNAME' because of insufficient disk space in filegroup 'DEFAULT'. Create the necessary space by dropping objects in the filegroup, adding additional files to the filegroup, or setting autogrowth on for existing files in the filegroup. I've found the following solutions but none work due to having no disk space on that drive, and since the DB is in a failed state I can't run most commmands. - DBCC SHRINKFILE - can't be run because doing a 'use DBNAME' fails - Detaching the DB and then changing the location of the MDF/LDF files, this fails because the DB is in an offline mode so you can't run detach. I'm at a loss about what else to try. Thanks.

  Read the article

• All network devices freezing when Airport Extreme Base Station is connected. Any ideas?

  - by Jon

  I've been troubleshooting this issue for a while, and through a series of events have it narrowed down to my airport extreme base station. I like this router, since I'm able to connect to IPV6 sites without any insane configuration (my alternate router is too old and doesn't support v6). My question is: Has anyone else had this issue, if so how is it resolved? If not, can you recommend a good IPv6 router? Here is how I came to the conclusion that it is the router: Devices: XBOX 360, HTC Incredible, Home-Built machine running FreeBSD, Home-Built machine running Ubuntu 10.04. 1.) Noticed freezing on Ubuntu Box. 2.) Noticed freezing on XBOX360 3.) Noticed freezing on HTC Incredible (only when connected to my network wirelessly). The above all happened at random times throughout the past few weeks. Over the last few days, I was playing XBOX and noticed that the XBOX and Ubuntu machines both froze. I picked up my phone, and it was also frozen. I reset all devices, power-cycled my router, and all was fine again. About two hours later, it happened again (I was playing Forza III, the XBOX froze; I went to the Ubuntu box and it was frozen; unfortunately, the HTC phone was not connected wirelessly, and the FreeBSD box was turned off). I can't even begin to imaging what a router could be doing to freeze devices with such differing hardware/software/OS, and I feel absurd for coming to this conclusion, but I have nothing else. I hooked up my archaic Netgear router, and have had no problems since. :(

  Read the article

• Error running Solr

  - by Jon H

  I'm trying to install Apache Solr for Plone, via collective.solr. I've followed the instructions above, and extended my buildout with: [buildout] extends = buildout.cfg https://github.com/Jarn/collective.solr/raw/master/buildout/solr.cfg [instance] eggs += collective.solr bin/buildout runs fine, however, when I try bin/solr-instance fg I get the following error: Traceback (most recent call last): File "bin/solr-instance", line 114, in <module> start(False) File "bin/solr-instance", line 43, in start stdout=logfp, stderr=logfp).pid File "/usr/lib/python2.6/subprocess.py", line 633, in __init__ errread, errwrite) File "/usr/lib/python2.6/subprocess.py", line 1139, in _execute_child raise child_exception OSError: [Errno 2] No such file or directory Graceful stop What am I missing / doing wrong?

  Read the article

• how to remove background layer of djvu file

  - by Jon

  Hello, I've downloaded some files from the Internet Archive. They come in different file formats and most of the time I use pdf. However, sometimes the scans are saves in colour instead of b/w. This makes it difficult/impossible to read on a dedicated ebook reader. In that case I downloaded the djvu files as on the PC you can select which layer (color, bw,fore,back) one would like to see. Selecting the bw gives excellent results. However, the ebook reader does not has this option. The question is, how can I remove /extract a layer from the djvu file and save only this layer. So far I've tried the following two approaches: 1) select bw in the djvu viewer on the PC and printed to postscript file. Followed by a ps2pdf conversion. This works, but generates a fairly large pdf file. Sure, I can again upload it to any2djvu but it just seems to much manual work for each file. 2) I tried the shared annotation feature and said (mode bw). This works on the PC as desired but is ignored on the ebook reader as the other layers are still present. Any help or suggestions would be greatly appreciated.

  Read the article

• How do I tell mdadm to start using a missing disk in my RAID5 array again?

  - by Jon Cage

  I have a 3-disk RAID array running in my Ubuntu server. This has been running flawlessly for over a year but I was recently forced to strip, move and rebuild the machine. When I had it all back together and ran up Ubuntu, I had some problems with disks not being detected. A couple of reboots later and I'd solved that issue. The problem now is that the 3-disk array is showing up as degraded every time I boot up. For some reason it seems that Ubuntu has made a new array and added the missing disk to it. I've tried stopping the new 1-disk array and adding the missing disk, but I'm struggling. On startup I get this: root@uberserver:~# cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md_d1 : inactive sdf1[2](S) 1953511936 blocks md0 : active raid5 sdg1[2] sdc1[3] sdb1[1] sdh1[0] 2930279808 blocks level 5, 64k chunk, algorithm 2 [4/4] [UUUU] I have two RAID arrays and the one that normally pops up as md1 isn't appearing. I read somewhere that calling mdadm --assemble --scan would re-assemble the missing array so I've tried first stopping the existing array that ubuntu started: root@uberserver:~# mdadm --stop /dev/md_d1 mdadm: stopped /dev/md_d1 ...and then tried to tell ubuntu to pick the disks up again: root@uberserver:~# mdadm --assemble --scan mdadm: /dev/md/1 has been started with 2 drives (out of 3). So that's started md1 again but it's not picking up the disk from md_d1: root@uberserver:~# cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md1 : active raid5 sde1[1] sdf1[2] 3907023872 blocks level 5, 64k chunk, algorithm 2 [3/2] [_UU] md_d1 : inactive sdd1[0](S) 1953511936 blocks md0 : active raid5 sdg1[2] sdc1[3] sdb1[1] sdh1[0] 2930279808 blocks level 5, 64k chunk, algorithm 2 [4/4] [UUUU] What's going wrong here? Why is Ubuntu trying to pick up sdd into a different array? How do I get that missing disk back home again? [Edit] - After adding the md1 to mdadm.conf it now tries to mount the array on startup but it's still missing the disk. If I tell it to try and assemble automatically I get the impression it know it needs sdd but can't use it: root@uberserver:~# mdadm --assemble --scan /dev/md1: File exists mdadm: /dev/md/1 already active, cannot restart it! mdadm: /dev/md/1 needed for /dev/sdd1... What am I missing?

  Read the article

• How do I fix TortoiseSVN displaying random icon overlays?

  - by Jon Cage

  I use TortoiseSVN (latest version) and sometimes all the icon overlays it uses get randomized with quite peculiar results. Is there any way to fix this?

  Read the article

• Using Twitter to accept messages for a web app

  - by Jon

  I'd like my web app to be able to accept direct messages via twitter. My app won't be sending our any spam, in fact it won't send out any messages at all. It will essentially be a bot controlled account as I would only access the account via an API to check for direct messages. Is this kind of usage permitted within twitter's t & c? Thanks.

  Read the article

• How to diagnose a Windows XP hard crash

  - by Jon

  I have a 64-bit Windows XP machine which has hard crashed several times today. The symptoms are that the screen just goes blank, then the reboot cycle starts. There is no blue screen and even though it is switched on, no crash dump file is created. On all occasions it has happened during a period of high CPU/memory activity. I have run a full Dell diagnostics with no failures. Any ideas how to track this down further? Thanks.

  Read the article

• Does aria2 support write small files in batch?

  - by Jon

  I'm using aria2 to download 8 million jpg from flickr. Each image is about 100KB. I got a list of urls of these images in a txt file, the format is: http://farm2.staticflickr.com/1070/1151334893_5a8e7f77f4.jpg I'm wondering whether aria2 support writing small files in batch? Say write 100 image to disk when all of them are download in the memory, not just write every single file when the download is finished. Because I think writing in batch will better protect my hard disk. Or do you have other software or opensource code to recommend?

  Read the article

• Enabling Shell colours through Putty SSH

  - by Jon

  I have set a number of configurations in my .bashrc file to set the appearance of shell on my Redhat machine. However, when I login as root using Putty, the colours are not shown. I can enable them again by typing 'su', which simply puts me back to root like I was when I logged into putty, but that isn't exaclty ideal. Is there some configuration file or something I can use to enable shell colours when I login with Putty? Thanks

  Read the article

• SBS 2008 reinstall on new machine

  - by Jon

  We purchased a single license on Windows Small Business Server 2008 for a medical office, and soon after a power fault caused the server to overload, destroying the power supply and motherboard. I reinstalled on a new server, and have the domain up and running again, but under system properties it tells me I still need to activate windows, and that the product key currently entered is invalid for activation. I've been trying to figure out how to get in touch with Microsoft to explain the situation and get a new activation key issued without having to pay for another license which we can't afford, but the online documentation hasn't been particularly clear on the subject. Does anyone know how to do that, or if I do need the activation key to continue using SBS 2008? (It currently tells me I have 56 days left to activate) Any tips would be appreciated. I'm not strictly a computer guy and I'm feeling a little lost.

  Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >