Search Results

Search found 911 results on 37 pages for 'jonathan akers'.

Page 14/37 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

• file corruption on read/write 2.6.32-22-server (happens across many kernels)

  - by Jonathan

  Hi Guys, I'm having an issue where after the server has been up for a period of time (~week/few days) the server will start reading corrupt data. For instance when I run a sha1sum of a file after a fresh boot it remains the same. However after a while I will start to get segfaults and from then on whenever I read this file I get a different sha1sum. I've checked S.M.A.R.T with long tests and I've run an extended memtest86+(12 passes) My lspci is as follows: 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3300 Graphics 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller 02:00.0 Ethernet controller: Atheros Communications Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0) 03:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. Device 3403 I could really use some help on this, do you have any idea what could cause this? It's really frustrating me as it seems to trigger entirely randomly and will not go away until I reboot. I'm also use KVM for virtualization as well as MD for software RAID on this server and the processor is a Phenom II X4 965. I don't believe it's the software raid however as this affects files also hosted on non-raid partitions so I don't know.

  Read the article

• Is there software that lets me drag windows between two PCs? (there is!)

  - by Jonathan

  I'm looking for a preferably free program that is similar to MaxiVista, which lets you extend you desktop to another desktops screen on the same network. But with MaxiVista you have to extend the entire screen. I'd like to just drag one window onto the other computers screen without extending the desktop. So on top of the other computer's windows. Kind of like a cross between MaxiVista and Windows 7' XP mode where you can run XP programs on the windows 7 desktop. EDIT: I am pleased to announce this is possible, though the windows is poor quality (8-bit color) but I believe thats just because MetaVNC isn't very up to date.

  Read the article

• How do I prevent spawning of zombie-like apache2 processes on Dreamhost VPS?

  - by Jonathan Hayward

  I have had a website for months or longer on a DreamHost VPS, and I have had vague memories on, in initial setup, having to turn off some customized Apache under /dh to get a standard Apache 2.x to work with. Things have been going along on an even keel, when I started making some changes lately and I found that when I tried to bounce Apache (/usr/sbin/apachectl restart), it couldn't bind to port 80, and my site had been converted from a big literature site to a small parking site. I tried to see what was listening on 80, and it was a DreamHost-customized Apache that had spawned. I killed all of them, restarted Apache, and changed the parent directory under /dh to mode 000. That was a day or two ago. I was bouncing Apache again in trying to get a new site to load under HTTPS, and I found that once again DreamHost's apache had spawned, from the directory I set to mode 000, and once again converted my site to a parking page. I renamed the directory, but I am very skeptical of whether I have permanently killed the DreamHost-customized Apache. Besides duct tape options like a crontab to kill and delete each minute, how can I permanently turn off the Apache processes that are spawning from a location under /dh and interfering with standard Apache? What should I be doing that I am not? Can DreamHost's technical support stop the interference? Thanks,

  Read the article

• Linux - How to manage the password of root?

  - by Jonathan Rioux

  We have just deployed a couple of Linux server. Each sysadmin will have his own account on the server (i.e.: jsmith), and will connect using SSH with a certificate which will be put into the "authorized_keys" file in their home directory. Once connected on the server, if they want to issue an elevated command, they will do like: sudo ifconfig They will then enter the root password. What I would like to know now are the best practices in managing that root password. Should I change it periodicaly? And how do I share that new password with the sysadmins? **Of course I will disable the root logon in SSH.

  Read the article

• How to make schema dumps comparable between Windows and Linux

  - by Jonathan

  I have two systems running, one on linux and the other on windows. From the linux box, I ran pg_dump against both systems and dumped the schema. pg_dump command: pg_dump -h HOST -U USER -s -f /tmp/out.sql DB_NAME After I removed all of the "--" comments, I diffed the files together. Diff output snippet, linux compared to windows: - ADD CONSTRAINT sys_c004775 FOREIGN KEY (ruleid) REFERENCES rule(ruleid); + ADD CONSTRAINT sys_c004775 FOREIGN KEY (ruleid) REFERENCES "rule"(ruleid); The linux dump does not quote any entities and windows does. Is this a function of some encoding or just of a difference between windows and linux? Is there an option in pg_dump to make the output more consistent?

  Read the article

• Browsing not working in Windows 8

  - by Jonathan Perry

  I'm using Windows 8 Professional installed on Windows 7 using the "Save my preferences and apps" installation option. The Windows works great, apps are downloading and I can listen to online radio stations using the TuneIn radio app meaning the internet connection is alive, however, when I open a browser (either Chrome or IE10) and try to browse the internet, I'm getting an "Unable to resolve DNS" error message. Prior to installing the internet browsing worked flawlessly I must say. I'm using ESET NOD32 Antivirus so I suspect that it might interfere with the web connection now, but I'm not so sure. Internet options show that the PC is set to resolve the DNS automatically. I don't know what to do. My other Win7 PCs in my wifi home network are connecting to the internet without any issues. If anyone can help me resolve this I'll be grateful :) Thanks

  Read the article

• Issues using gmail with google apps and external domain

  - by Jonathan Kelly

  I have recently tried to use gmail through google apps as my main email client, but I'm experiencing a few different problems. I am managing the domain (conjunktiondesign.co.uk) through 123reg.co.uk but it is hosted through fasthosts.co.uk. I transfered the domain to 123reg as fasthosts did not allow me to change the MX records myself. I followed the setup instructions step by step on google apps and changed the MX records as they told me to. My email was now working perfectly but my website was down and I was getting the following error: The dnsserver returned: No DNS records I have a friend that is using the same system as me (ie. Externally hosted domain and google apps mail) and I changed my 123reg details to the same that he had (as his was working perfectly - both email and website). I changed my name servers to point to fasthosts, rather than 123reg and I added an A record called '@' pointing to fasthosts IP address. I also created another A record called 'www' pointing to fasthosts IP address. After I did this, my website worked almost immediately but I have only realised that since changing it my email is now down. I have not received anything since Saturday. I am a web designer and would consider myself fairly tech savvy, but I have no idea about A records, CNAME's and all the things I have been messing about with! What I ultimately need is someone to help me get my email and website working at the same time, rather than one being down when the other is OK. I seem only able to get one or the other working. I have now changed the name servers back to 123reg in an attempt to get my email back as it is more important than my website at this stage. Any help is much appreciated. Thanks.

  Read the article

• WMP Skipping Chapters When Restored to Fullscreen

  - by Jonathan Sampson

  I just noticed a rather interesting issue with WMP. I'm watching a DVD while working, and noticed that if I minimize it to my taskbar, and open up the small preview window I can watch it just fine. But if I restore it while it's playing, it immediately skips ahead to the next chapter, blowing right past several minutes of content. Is this standard behavior? Is there a work-around to keep it from doing this?

  Read the article

• What's the best Remote Desktop Application?

  - by Jonathan Sampson

  I've got family members spread over many states that always want me to remote into their machines and help them with various issues. For this, what is the best remoting-application available, comparing features to cost? In the past I've used VNC.

  Read the article

• Qmail & Open Relay on local domains

  - by Jonathan

  Hello. I have a dedicated server on 1&1 and I manage it with Plesk. The problem is that if I try to send a mail outside the server, I must to authenticate with the email and the password, but if I send an email to a address inside of my server I don't need neither email or password. This is a problem because the spammers are sending mails without any problem to the server accounts. We are receiving about 900 - 1200 emails everyday! What can I do? I use qmail on CentOS Thanks

  Read the article

• How to tell if OpenGL is really working in Ubuntu 10.04

  - by Jonathan

  I have a lenovo S9e running Intel integrated graphics. Here is my lspci output related to the graphics: 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) Subsystem: Lenovo Device 3870 Flags: bus master, fast devsel, latency 0 Memory at f0580000 (32-bit, non-prefetchable) [size=512K] Capabilities: [d0] Power Management version 2 I want to know how I can make sure OpenGL support is running in full on an Ubuntu 10.04 installation. I have a few hints to think that it is not: The "Desktop Effects" will not load Apps such as stardock, when attempting to use OpenGL rendering, will display black boxes instead of transparency In the games Pioneers, the number-tile icons are suspiciously just black circles Windows games running with Wine will only support software rendering, not hardware rendering When I boot into a Knoppix LiveCD, the desktop effects do work, splendidly, meaning compiz detects my computer as capable. My problem with troubleshooting is that Canonical has basically eliminated the conf-file-based mechanism of X11 as far as I can tell, thus making it even harder to ensure graphics modules are loading properly. How do I debug and test OpenGL on m Ubuntu 10.04 installation?

  Read the article

• problem getting php_oci8 working on linux RHEL 5

  - by Jonathan

  Hi All, I'm installing oracle oci8 on a linux server here and I am having an issue where php_oci8.so does not seem to be able to find the libclntsh.so.11.1. I've got the instant client installed and it shows up fine in ldconfig -p , but when I do ldd on the php_oci8.so it shows up as not found. Does anyone have any ideas as for what I can check ?

  Read the article

• Apache - mod_pagespeed freezes my website

  - by Jonathan Rioux

  I have installed the mod_pagepseed module for Apache. I am using Debian so I downloaded the .deb file, and installed it successfully. I then configured some filters, and it worked like a charm for some minutes. Then after something like 10 minutes, my website no longer responded to the requests. When I was requesting for my website, it said "Waiting for www.blablabla.com" and I never got the page back from the server. I checked the processes running on my Debian box with top -d 0.5, and nothing eats up the CPU. To make my website responding to requests again, I must do a /etc/init.d/apache2 restart. And then it works again with mod_modspeed applying it's filters for a couple of minutes, and no more response again. How can I diagnose this issue? Is there some other configurations in the mod_pagespeed.conf file that I must set?

  Read the article

• Linux Defualt Startup Display PCI to fix black boot screen

  - by Jonathan

  You heard it all before black screen on boot after perfectly fine install of most linux ubnuntu mint etc distributions (the netbook works fine) It has an Intel N10 integrated graphics chipset. I have actually found that if I plug in an external display then remove it the default screen turns on and my laptop works fine drivers all great - I have tried the screen cycle button fn f7 but doesn't work when no display is plugged in. It also works out all the correct resolutions and no modification of the grub bootloader or creating any xorg configs. So I think my monitor is forcing to a display that doesn't exist. Do you know if there is anyway I can force it to choose a different screen at boot so I can get a login screen? I can use nomodeset on grub but xrandr cant add the damned 1024 600 60 resolution that I need! Ideas guys?

  Read the article

• Enabling mycrypt on CentOS

  - by Jonathan Sampson

  When attempting to load a Kohana3 app onto my server, I was warned that mycrypt was not enabled. How would I go about enabling mycrypt on my CentOS server?

  Read the article

• Route through site-to-site VPN not working

  - by Jonathan

  I'm trying to set up a site-to-site VPN using RRAS on two 2K8r2 servers since yesterday. The connection is working at this point, but I can't get it to send traffic from one site to the other one. Set up: the set up is the same on both sites: the server is connected to a router that's connected to a modem. The routers act like a DHCP-server and assign IP addresses from the range subnet.21-subnet-.100. Both servers use a static IP address, subnet.11, and are set up as DMZ. Configuration: the servers are configured using the wizard to set up a site-to-site connection. This works with a demand-dial interface and a PPTP VPN connection. As mentioned, the VPN connection work properly. Problem: I can't get the servers to send the traffic for the other site, to be sent through the VPN connection. I added a static route on both server (home, office 1) and I can see the result in the IP routing table (home, office 1). I did this because the route didn't show up automatically. My guess is that this last step isn't right, for example because the routing table states "non demand-dial", which seems not correct. Home: Subnet: 10.0.1.0/24 Router: 10.0.1.1 Server: 10.0.1.11 (DMZ) DHCP: 10.0.1.21-10.0.1.100 RRAS DHCP: 10.0.1.101-10.0.1.150 Office 1: Subnet: 10.0.2.0/24 Router: 10.0.2.1 Server: 10.0.2.11 (DMZ) DHCP: 10.0.2.21-10.0.2.100 RRAS DHCP: 10.0.2.101-10.0.2.150 I hope someone has an idea to get this route working!

  Read the article

• Setting up xpra for client use in OS X

  - by Jonathan

  I've been trying to get xpra to run on OS X for the last few days to connect to my Ubuntu server. Note that there's a GUI for it called shifter, but that (at least on OS X) is still far too buggy. For those who don't know what xpra is, if you know what screen is, it's like screen for GUI X Windows apps tunneled over ssh. You can render a remote X app locally so it's faster than sending a series of compresses screen shots (like VNC), but with xpra you can disconnect and reconnect on different computers. To get the basic functionality you can just type "ssh -X server.location" and any GUI app you open from the command line will open locally. I've been able to get xpra to build by doing the following: Download pari-all-0.0.6.tar.gz from the xpra site listed under upstream and untar it. Issue the following Mac Ports command (Dependencies thanks to RogBlog): sudo port install python25 python26 py26-pyrex py26-gtk xorg-libXtst py25-gobject py25-gtk py25-nose py26-nose xorg-libXdamage xorg-libXcomposite xorg-libXtst xorg-libXfixes In the upstream list of v0.0.06 patches (NOT 0.0.8pre!) on the xpra site listed above, download mswindows-conditional-pyrex.patch. Open the patch with your favorite text editor and change the single occurrence of "win" in it to "darwin". Apply the patch to setup.py. Run do-build in the command line. Now where I'm stumped: how do I run xpra? The build produces a sub directory called install/bin in which xpra is located, but when I try to run it I get the following error: Traceback (most recent call last): File "./xpra", line 4, in import xpra.scripts.main ImportError: No module named xpra.scripts.main There is a file called main.py under xpra/scripts, but I don't know any python and I'm not sure if this is what it's looking for, and what to do with it even if it is. My goal is to set up xpra so I can install it into /usr/bin (or some other common path for executables) and execute it whenever I please. What do I do next?

  Read the article

• NTP doesn't sync

  - by Jonathan

  I'm using Meinberg NTP to sync the time in a VPS. The clock refuses to sync - there's a ~30s shift comparing to other servers. Meinberg NTP comes with a status script that checks hte delay\jitter every 10s and it is showing all zeros. Actions I've taken which didn't help: Restarted the NTP service using a script that comes with Meinberg NTP Added port 123 for UDP and TCP as an exception port to Windows Firewall Added Meinberk NTP executables as an exception program to Windows Firewall validated iburst appears after each server listed in the configuration file Restarted the server The OS is a Windows Server Standard SP2 32bit. What did I miss?

  Read the article

• SED and Unicode Quotation Marks

  - by Jonathan Patt

  When testing against this string: “… so that’s that… ” The following should, but does not, match the opening quotation mark and following ellipsis and space: sed "s/\([“‘\"']…\) /\1/g" However, this correctly matches the second ellipsis and following space and closing quotation mark: sed "s/… \([”’\"'.!?]\)/…\1/g" If I split the first apart it works fine: sed -e "s/\(“…\) /\1/g" \ -e "s/\(‘…\) /\1/g" \ -e "s/\(\"…\) /\1/g" \ -e "s/\('…\) /\1/g" So why doesn't it work when it's grouped together? Especially when it works fine with the closing quotation marks.

  Read the article

• What's going on with my server? High load, lots of idle CPU time, low disk utilization

  - by Jonathan

  I run a web site and send a legitimate opt-in, daily email newsletter to subscribers. Both the web hosting and email sending are done by the same machine. I have about 100,000 subscribers who have opted in to my daily email newsletter. My PHP script did a pretty good job sending mail to all of them until fairly recently, but as the list has grown I can't keep up. When I run top, I have very high load--usually at least 6 or 7, sometimes as high as 15--even though I only have two CPUs. However, when I run sar, my CPU is idle an average of about 30% of the time. So, it seems I'm not CPU bound. When I run iostat, it seems as though I'm not disk bound because my %util for each device is very low (no more than 5%). Given that I don't seem to be CPU bound or disk bound, why is top reporting such high load? Additionally, since I don't seem to be CPU bound or disk bound, why is my email sending script not able to keep up? Here's what I see when running top: top - 11:33:28 up 74 days, 18:49, 2 users, load average: 7.65, 8.79, 8.28 Tasks: 168 total, 5 running, 162 sleeping, 0 stopped, 1 zombie Cpu(s): 38.9%us, 58.6%sy, 0.8%ni, 0.0%id, 0.7%wa, 0.2%hi, 0.8%si, 0.0%st Mem: 3083012k total, 2144436k used, 938576k free, 281136k buffers Swap: 2048248k total, 39164k used, 2009084k free, 1470412k cached Here's what I see when running iostat -mx: avg-cpu: %user %nice %system %iowait %steal %idle 34.80 1.20 55.24 0.37 0.00 8.38 Device: rrqm/s wrqm/s r/s w/s rMB/s wMB/s avgrq-sz avgqu-sz await svctm %util sda 0.19 71.70 1.59 29.45 0.02 0.07 5.90 0.55 17.82 1.16 3.59 sda1 0.00 0.00 0.00 0.00 0.00 0.00 7.10 0.00 13.80 13.72 0.00 sda2 0.05 50.45 1.13 24.57 0.01 0.29 24.25 0.35 13.43 1.15 2.97 sda3 0.05 10.17 0.20 2.33 0.01 0.05 43.75 0.05 20.96 2.45 0.62 sda4 0.00 0.00 0.00 0.00 0.00 0.00 2.00 0.00 70.50 70.50 0.00 sda5 0.07 0.22 0.03 0.07 0.00 0.00 32.84 0.08 856.19 8.03 0.08 sda6 0.02 5.45 0.03 0.72 0.00 0.02 67.55 0.02 26.72 5.26 0.39 sda7 0.00 1.56 0.00 0.42 0.00 0.01 38.04 0.00 8.88 5.84 0.24 sda8 0.01 3.84 0.20 1.35 0.00 0.02 28.55 0.05 31.90 4.08 0.63 Here's what I see when running sar: 09:40:02 AM CPU %user %nice %system %iowait %steal %idle 09:50:01 AM all 30.59 1.01 49.80 0.23 0.00 18.37 10:00:08 AM all 31.73 0.92 51.66 0.13 0.00 15.55 10:10:06 AM all 30.43 0.99 48.94 0.26 0.00 19.38 10:20:01 AM all 29.58 1.00 47.76 0.25 0.00 21.42 10:30:01 AM all 29.37 1.02 47.30 0.18 0.00 22.13 10:40:06 AM all 32.50 1.01 52.94 0.16 0.00 13.39 10:50:01 AM all 30.49 1.00 49.59 0.15 0.00 18.77 11:00:01 AM all 29.43 0.99 47.71 0.17 0.00 21.71 11:10:07 AM all 30.26 0.93 49.48 0.83 0.00 18.50 11:20:02 AM all 29.83 0.81 48.51 1.32 0.00 19.52 11:30:06 AM all 31.18 0.88 51.33 1.15 0.00 15.47 Average: all 26.21 1.15 42.62 0.48 0.00 29.54 Here are the top handful of processes listed at the particular time I happened to run top -c: PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 8180 mysql 16 0 57448 19m 2948 S 26.6 0.7 4702:26 /usr/sbin/mysqld --basedir=/ --datadir=/var/lib/mysql --user=mysql --pid-file=/var/lib/mysql/bristno.pid --skip-external-locking 26956 brristno 17 0 0 0 0 Z 8.0 0.0 0:00.24 [php] <defunct> 26958 brristno 17 0 94408 43m 37m R 5.0 1.4 0:00.15 /usr/bin/php /home/brristno/public_html/dbv.php 22852 nobody 16 0 9628 2900 1524 S 0.7 0.1 0:00.17 /usr/local/apache/bin/httpd -k start -DSSL 8591 brristno 34 19 96896 13m 6652 S 0.3 0.4 0:29.82 /usr/local/bin/php /home/brristno/bin/mailer.php 1qwqyb6 i0gbor 24469 nobody 16 0 9628 2880 1508 S 0.3 0.1 0:00.08 /usr/local/apache/bin/httpd -k start -DSSL 25495 nobody 15 0 9628 2876 1500 S 0.3 0.1 0:00.06 /usr/local/apache/bin/httpd -k start -DSSL 26149 nobody 15 0 9628 2864 1504 S 0.3 0.1 0:00.04 /usr/local/apache/bin/httpd -k start -DSSL

  Read the article

• Postgresql connection refused

  - by Jonathan

  I'm trying to remotely connect to my postgresql database. I have two virtual machines set up both running ubuntu 14.04. I am trying to connect to the second vm using the first vm using psql -h 10.0.1.23 -U postgres -d postgres But I receive the error: Could not connect to server: Connection refused Is the server running on host "10.0.1.23" and accepting TCP/IP connections on port 5432? I have changed the pg_hba.conf and added host all all 10.0.1.64/24 md5 host all all * md5 host all all 0.0.0.0/0 md5 And changed the postgresql.conf listen_address=" * " In an attempt to allow all incoming connections. I have also tried to change the firewall settings, but I am unsure of whether or not the ports are properly listening for the connection. Edit: Output of netstat -an | grep -E '^tcp[^6].*LISTEN' tcp 0 0 127.0.1.1:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:23 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:5432 0.0.0.0:* LISTEN

  Read the article

• Scalable WordPress Host for High-Volume Site?

  - by Jonathan Eunice

  I need recommendations for a scalable web host for a high volume WordPress web site. For my purposes, high-volume might be 100K-500K visitors/hour. Might think towards a 1M/hour burst rate as a "high water mark." I know WP isn't the highest-performing platform out there (ha!), but it's non-negotiable. I can do "the usual optimizations" (e.g. put static files in a CDN, run and follow the advice of performance analyzers like YSlow, etc). But it will still be WordPress, and there will be a dozen or so plugins involved. So, where to host the site? Most "what's the best WordPress host?" discussions seem to focus on lowest-cost. I need the opposite. What are the high-volume, scalable, or clustered WordPress hosts with which you've had great experiences?

  Read the article

• Linux - How to completety clean up a software installation

  - by Jonathan Rioux

  Hi, I am running under Debian and I have recently upgraded to Squeeze. Since then, I am having so much problems with Webmin. So I have decided to remove it using: apt-get remove webmin And then I downloaded the sources of Webmin 1.530 and compiled it. But the installation process has been stucked for an hour so I canceled it. I even tried to install it using the .deb file without success (installation stucks for hours). From now, I cannot install Webmin since I uninstalled it. So I would like to know how can I make a full clean up of any traces of Webmin on my server. And then I will retry to install it.

  Read the article

• Encrypting peer-to-peer application with iptables and stunnel

  - by Jonathan Oliver

  I'm running legacy applications in which I do not have access to the source code. These components talk to each other using plaintext on a particular port. I would like to be able to secure the communications between the two or more nodes using something like stunnel to facilitate peer-to-peer communication rather than using a more traditional (and centralized) VPN package like OpenVPN, etc. Ideally, the traffic flow would go like this: app@hostA:1234 tries to open a TCP connection to app@hostB:1234. iptables captures and redirects the traffic on port 1234 to stunnel running on hostA at port 5678. stunnel@hostA negotiates and establishes a connection with stunnel@hostB:4567. stunnel@hostB forwards any decrypted traffic to app@hostB:1234. In essence, I'm trying to set this up to where any outbound traffic (generated on the local machine) to port N forwards through stunnel to port N+1, and the receiving side receives on port N+1, decrypts, and forwards to the local application at port N. I'm not particularly concerned about losing the hostA origin IP address/machine identity when stunnel@hostB forwards to app@hostB because the communications payload contains identifying information. The other trick in this is that normally with stunnel you have a client/server architecture. But this application is much more P2P because nodes can come and go dynamically and hard-coding some kind of "connection = hostN:port" in the stunnel configuration won't work.

  Read the article

• Stuck GhostScript processes, how to debug?

  - by Jonathan

  Having a problem with Ghostscript processes that don't end. This does not happen often, probably once every 3 weeks we see this issue with 1-3 processes. Running CentOS 6.4 on a VPS from Rackspace. We use PrinceXML to generate PDFs which uses GhostScript to handle fonts. Here's an image of top: http://i.stack.imgur.com/J9D7D.jpg As you can see those two processes are using a lot of resources, I haven't killed them yet in hopes someone can help me diagnose. I'm a developer not a server admin so I have a basic knowledge of *nix but no clue on how to fix this. Installed strace and ran it on each process with the following command: strace -p 20619 -s 80 -o gs.txt Left it for 5m, gs.txt is empty? Thanks in advance!

  Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >