Search Results

Search found 976 results on 40 pages for 'josh hornell'.

Page 14/40 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

• Why did my zpool replace never finish and what should I do now?

  - by Josh

  I have a ZFS zpool with two disks in a mirror configuration, da0 and da1. da1 failed, and so I replaced it with da2 using zpool replace BearCow da1 da2 This ran for a few hours, during which zpool status showed that the array was being resilvered. When that finished, zpool status showed that the resilver was completed, but the array was still degraded... I tried a zpool scrub and a zpool clear, but the array still shows as degraded: [root@chef] ~# zpool status BearCow pool: BearCow state: DEGRADED scrub: scrub completed after 0h20m with 0 errors on Tue Oct 9 16:13:27 2012 config: NAME STATE READ WRITE CKSUM BearCow DEGRADED 0 0 0 mirror DEGRADED 0 0 0 da0 ONLINE 0 0 0 replacing DEGRADED 0 0 0 da1 OFFLINE 0 0 0 da2 ONLINE 0 0 0 errors: No known data errors I can't zpool replace BearCow da1 da2 anymore because da2 is already a member of BearCow... This is FreeBSD (FreeNAS) running ZFS pool version 15. How do I get my array to show as healthy again?

  Read the article

• ISPs with good upload speeds? [closed]

  - by Josh Comley

  I am a web developer, and I spend most of my time not waiting for downloads but waiting for my latest build of a website to publish to a test site. I use the excellent BeyondCompare to ensure I only upload what I need to upload. But still, if a 2MB C# DLL has changed, so be it. And I must wait. At work we host our own servers and have a dedicated line, so for 8.5 hours of my day I have blistering upload speeds across the web, which is nice. At home however, it's a different story. I am with Virgin Media on their XL internet package (I think). I think that means I get 256Kb upload and 20Mb download. So I have began to wonder - are there any ISPs in the UK with good upload speeds? If you know of any for other countries, do post for other's sake, but please specify which country your post is relevant to.

  Read the article

• How can I get the ./configure options used to build Apache?

  - by Josh

  I am using CentOS, and would like to build from source with the newer version of apache using the same configure options as the package obtained using yum, with an adjustment or two. How would I go about acquiring that?

  Read the article

• Quick easy program to view network traffic?

  - by Josh

  I leach my neighboors wireless (it's all good I get him back), but I need a way to monitor the incoming and outgoing IPs/domain names on my own end, only because I think I have a trojan. Like some easy program you know?

  Read the article

• Quick easy program to view network traffic?

  - by Josh

  I leach my neighboors wireless (it's all good I get him back), but I need a way to monitor the incoming and outgoing IPs/domain names on my own end, only because I think I have a trojan. Like some easy program you know?

  Read the article

• How can I boot directly to a VirtualBox (.vdi) image (possibly via hypervisor)?

  - by Josh

  I have a system image in VirtualBox as a .vdi file. I am aware of how to convert this to other formats of VM using VBoxManage. I'd like to boot this image locally on a number of clients which currently have no OS installed. What's the simplest way to boot into this VM from bare metal? I'm willing to install some minimal OS if necessary. Is this even possible? Maybe there's something out there along the lines of VDI Blaster that will load a locally stored VM?

  Read the article

• apache requests failing

  - by Josh

  I'm trying to figure out why sometimes the client fails to load objects/requests from a dynamic page served from Apache/MySql/Debian machine. Let's say 13 objects are to be loaded for a total of 185.3 KB load, with no external objects (no DNS lookups) and no other traffic at the same time, randomly some of those object do not load. However, if I perform a refresh, sometimes all of them load or some might fail again. I only have 1Mbps/up and my DNS is been hosted externally (everydns). What could be the reason of this issue? Any comments will be appreciated.

  Read the article

• Random Computer Crashes

  - by Josh W.

  Ok, here's a wierd one for you all. Occasionally my PC here at work will crash in a very peculiar way. My dual monitors will suddenly go blank as if there is no longer a video signal, the USB mouse light will go dark and mouse stays unresponsive, the keyboard lights will not change status when the appropriate keys are pressed (Num/Caps/Scoll Lock). The CD Tray WILL open and close. But the computer will not respond to a ping request. For all intents & purposes it's as if the computer is off, except it wasn't intentional by me. The power light and internal fans are still on and I've now lost any unsaved work. Now here's where it gets wierd. This PC is part of a batch of PC's we got from a local vendor who does our initial system builds. Mine, and 6 other co-workers PCs all have the same issue. Originally we thought it was a bad combination of hardware, but through trial and error the only thing we haven't eliminated are the OS, Mobo & CPU. The problem was so bad for some of them that they ended up going back to their 5 year old dinosaurs in order to get some work done, for me the problem isn't as bad, maybe once every other day or so, but still enough to bite me in the ass if I've forgotten my ritualistic pressing of CTRL-S every 1-5 minutes. In this case we've tried two different video cards, two different power supplies, two different memory configurations, running on a UPS/not on UPS, updating/rolling back video drivers, three different bios revisions. The only things we haven't swapped are the mobo & cpu, mainly because a new mobo means a new Hardware Abstraction Layer, ie re-install of windows and there's alot of other software on this PC that takes forever to reload by hand. There was a base image that our systems team created with all the drivers installed and the basic setup of software our company uses, but they then must customize the setup for us programmers so it takes a while to get a new configuration up and going. I'm a programmer by day and am usually pretty good at diagnosing computer problems whether through trial and error or not. We've pretty much exhausted all the ideas we can think of here, short of a new mobo/cpu. Was hoping someone out there might have anything else we can try.. Relevant Parts: OS: XP Pro 32-bit Motherboard: Intel DG41RQ CPU: Intel Core-2 Quad Q9400 @ 2.66GHz Current BIOS Version/Date Intel Corp. RQG4110H.86A.0014.2010.0306.1151, 3/6/2010 Dual LCD's, Viewsonic VG930m & Samsung SyncMaster 910v (other people have different models, but listed in case there's some very wierd problem with the signals being sent/received) PS/2 Keyboard USB Microsoft Intellimouse BIOS Versions Tried: R 0013 12/23/2009 R 0014 3/6/2010 Video cards Tried GeForce 8400 GS Radeon HD 4350 - ASUS EAH4350 Two Different Power Supplies a 380W & 550W Ram Configurations 2GB - 1 x 2GB 4GB - 2 x 2GB

  Read the article

• Speakers will not work after I use USB Headset

  - by Josh K

  I am trying to configure my SteelSeries Siberia V2 Frost USB Headset to work with my 2.0 speakers using a jack. My goal is to find a easy way (no restart) to switch playback from my headset and my speakers and vice-versa. If i plug my headset in and make it the default device then restart my application/web page then the sounds works out of headset. If I switch the default to my speakers and restart apps/web pages then sound does not play. I know my speakers are on because if I configure them through windows and test, the sounds play, and sounds also play when I test it through my audio manager. Even if I unplug my headset, I still cannot get sound out of my speakers unless I restart My audio manager is RealTek HD Audio Manager, Windows 7 x64. I have tried the speaker back, usb front. speaker front, usb in front port. I have not tried speaker back, usb back.

  Read the article

• Is SSL to the proxy good enough?

  - by Josh Smeaton

  We are currently trying to decide on how best to do SSL traffic in our environment. We have an externally facing Apache proxy server that is responsible for directing all traffic into our environment. It is also doing the SSL work for the majority of our servers. There are one or two IIS servers in particular that are doing their own SSL, but they are also behind the proxy. I'm wondering, is SSL to the proxy good enough? It would mean that traffic within our network is identifiable, but is that such a big deal?

  Read the article

• What is preventing me from upgrading / installing Fixefox extensions?

  - by Josh

  I am trying to install a Firefox extension into Firefox 3.6.13 under OS X 10.5.8, and I keep getting an error message: Firefox could not install the file at because: Download error -228 I have read this and found it unhelpful. My cache is 500 MB and ~/Library/Caches/TemporaryItems is writable: [jnet@Stan ~]$ ls -la ~/Library/Caches/TemporaryItems total 16 drwx------ 5 jnet jnet 170 Jan 27 20:51 . Any idea how I can correct this?

  Read the article

• Internet Problem: Wireless connected but no connection to internet

  - by Josh K

  Hey i have a interesting network setup on a laptop here and for some reason the internet isnt working. I am connected to a secure network via wireless router and taskbar says i am connected and with good signal strength but in my internet browser i cant connect to any websites, the error is: This webpage is not available. (Chrome) I am using Chrome, but websites dont work on IE either. Heres a little background on the setup i have. I have a Ethernet connected to the laptop with a static ip, and then i have the wireless setup with DHCP enabled. I am using the ethernet to connect to the network (for remote desktop) but the wireless for internet (to avoid the network firewalls). this set up has worked fine for a few months, but i cant figure out what is going on now. Might be worth it to note it is a Lenovo Thinkpad and i just uninstalled ThinkVantage Access Connections (as it was giving me ample problems prior to this one, which i consider a step up) Tried repairing connection as well, let me know if you guys have any ideas please! EDIT: Solved-Dead Modem in the server room.... Sorry guys didn't have access to that myself

  Read the article

• Linux - What do the common root folder names mean?

  - by Josh

  I am rather new to linux, but I have installed a few different flavors. I noticed they all have similar folder names in the root directory bin boot dev etc home lib lost+found media mnt opt proc root sbin selinux srv sys tmp usr var I googled around, but couldn't find anywhere that explained the purpose of each of these. I understand a couple, but could anyone point me somewhere or give a quick breakdown of the common ones.

  Read the article

• Having trouble keeping a 1GB RAM Centos server running

  - by Josh

  This is my first time configuring a VPS server and I'm having a few issues. We're running Wordpress on a 1GB Centos server configured per the internet (online research). No custom queries or anything crazy but closing in on 8K posts. At arbitrary intervals, the server just goes down. From the client side, it just says "Loading..." and will spin more or less indefinitely. On the server side, the shell will lock completely. We have to do a hard reboot from the control panel and then everything is fine. Watching "top" I see it hovering between 35 - 55% memory usage generally and occasional spikes up to around 80%. When I saw it go down, there were about 30 - 40 Apache processes showing which pushed memory over the edge. "error_log" tells me that maxclients was reached right before each reboot instance. I've tried tinkering with that but to no avail. I think we'll probably need to bump the server up to the next RAM level but with ~120K pageviews per month, it seems like that's a bit overkill since it was running fairly well on a shared server before. Any ideas? httpd.conf and my.cnf values to add? I'll update this with the current ones if that helps. Thanks in advance! This has been a fun and important learning experience but, overall, quite frustrating! Edit: quick top snapshot: top - 15:18:15 up 2 days, 13:04, 1 user, load average: 0.56, 0.44, 0.38 Tasks: 85 total, 2 running, 83 sleeping, 0 stopped, 0 zombie Cpu(s): 6.7%us, 3.5%sy, 0.0%ni, 89.6%id, 0.0%wa, 0.0%hi, 0.1%si, 0.0%st Mem: 2051088k total, 736708k used, 1314380k free, 199576k buffers Swap: 4194300k total, 0k used, 4194300k free, 287688k cached

  Read the article

• How to split audio into multiple channels from optical S/PDIF or 1/8"?

  - by Josh M.

  I have a motherboard which has an optical S/PDIF output or 1/8". I'd like to "split" that signal into the appropriate channels so that I can then connect that to the wires behind my car's headunit which, in turn, run to the amp. The factory Bose amp just takes a single connector with a million wires running out of it, so that's why I would need to separate the signal into separate channels. On the other end there are four RCA connectors: front left, front right, rear left, rear right. The sub-woofer signal does not require an additional connection. Edit: Revised to include S/PDIF or 1/8".

  Read the article

• Add Clamd as a service to CentOS?

  - by Josh

  As I understand I think I need to add something to init.d, but I am not sure what to add. At the moment to start clamav I have to do clamd start. I would like it as a service so I can start it on run level 3 as a service. I realize I could probably do this through a shell script in the right runlevel, but I would like to be able to use chkconfig to configure it.

  Read the article

• View Public Key in Domain Key for a Domain

  - by Josh

  Using Jeff's blog post I'm creating domain keys for my account. I wanted to verify the setup using Get or Host command with Bind for Windows but I'm lost one of the commands. I can see view the _domainkey. txt file with this command: host -t txt _domainkey.stackoverflow.com but I'm at a loss at how I'd find the selector record. Jeff points out it can be anything before the before the period in "._domainkey.domain.com" but how would I list all records if I didn't know the exact query name? Is there a wildcard I could use to view all TXT or all records under this section?

  Read the article

• Linux Mint Constantly freezing on Dell XPS L502X

  - by Josh

  I recently partitioned my hard drive to dual boot the existing Windows 7 with Linux Mint because I am tired of using Windows, especially the lack of terminal. I want to eventually remove Windows 7 and just run it from a VM within Linux Mint, but I want to make sure that I like the Mint before going all in. I ran Linux Mint on a VM inside Windows for a while, enjoyed it, and never had any issues with it. Since installing on my hard drive it has started freezing every 5-10 minutes, and the only way to get it back is to either power down, or close the lid and reopen once it sleeps. I've also tried running Ubuntu on dual boot in the past, and while it never froze, the battery life was terrible, and the fan was constantly running. I'm experiencing the same battery/fan problem with Mint, which doesn't make sense to me, as Linux should be lighter on the CPU than windows. If I had to guess I'd say it's probably a driver thing, with my video card or fan or something. My battery life in Windows is ~2 hours and its about 40 minutes in Linux. At this point, that is even if my laptop doesn't freeze before then. On a less important note, I also have an intel Centrino 6150 WiMax card that I'd like to be able to use, but that won't register on the Linux system either. I have tried downloading drivers for both of these, but neither have solved my problems. I'm definitely getting frustrated and am getting close to giving up on Linux even though I dread working on a Windows machine.

  Read the article

• Setting up Konico Minolta 1400w printer on windows vista 32bit

  - by Josh

  One of my neighbors asked me to help them setup this old printer on their computer (thier other printer is broken) so after fighting with it for about an hour but to no avail. Every time I try to install it, windows just recognizes it a as "print to file printer" as in it will only print to an output file. It's kinda urgent so speedy help would be appreciated.

  Read the article

• Primary/secondary ethernet interfaces via NetworkManager in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local... EDIT: Here's my routing table: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 172.16.151.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 172.16.30.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.1.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 172.16.30.2 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.0.1 0.0.0.0 UG 0 0 0 eth1 I want the 172.16.30.2 network to be the primary one and the 10.1.0.0 network to be the secondary one. EDIT2: My nameservers are also incorrect. It seems like Ubuntu is bringing the networks up in order, eth0, then 1, then 2, and the DHCP information from eth1 is overriding eth0, and eth2 is overriding eth1. How can I reverse this so the DHCP information from eth0 is the "master"? EDIT3: This seems to be an issue with Gnome's NetworkManager.

  Read the article

• CHROOT for shell script testing

  - by Josh

  I am looking at setting up a shell script in order to properly document and automate the process I am using to setup a few servers we have. In order to test the shell script through its different stages I was thinking a CHROOT would be ideal, since I can wipe out the "virtual root" and create it on the fly. I have never used CHROOT before, however. I was just curious what are the exact steps I would need to follow to implement this process of creating a chroot (with the basic core functions that would be needed to install apache/php/etc.)? and then destroying it?

  Read the article

• Installed Bunch of New Fonts on Windows 7 - Now None Show Up and System Lags

  - by Josh Stodola

  So I went to install about 5,000 fonts on my Windows 7 64-bit machine. It was slow to install them, and I had to leave. I came back and my PC was shut down, and I had to go through the Windows recovery BS when I powered it on. Now my computer runs EXTREMELY slow and any program that has a font menu locks up my whole machine (nothing in Microsoft Office works). When I go to "Fonts" in the control panel, it says 0 items. I went through all of the font settings trying to get them to appear. Nothing helps. I tried to bring up the Character Map and that froze up my machine too. How can I fix this? If I do not get this issue resolved soon, I am wiping this drive and going back to XP (and probably never purchasing another version of Windows again). I never had any issues with XP and have had nothing but performance problems when switching to Windows 7. My quad-core intel extreme with 8GB of RAM should never flinch with the kind of work that I do, and something simple like playing a song off an external HD takes up to five seconds on Windows 7. Unbelievable that I had to pay for this crap!

  Read the article

• How can I avoid my web browser from redirecting to localhost using WAMP in Windows7?

  - by Josh

  I'm currently using Windows 7 with WAMP to try and work on some software, but my web browsers will not accept cookies from the "localhost" domain. I tried creating a few bogus domains in my hosts file by pointing them to 127.0.0.1 but when I type them in I am automatically redirected back to localhost. I have also configured virtualhosts in apache to correspond with the domains I added to the hosts file and it still redirects back to localhost. Is there anything special I must do on Windows 7 to get around this localhost redirect? Thanks for looking :) I'll include my host file here: # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. # 127.0.0.1 localhost # ::1 localhost 127.0.0.1 magento.localhost.com www.localhost.com Thanks for looking :)

  Read the article

• Is it faster to create indexes before or after data loading in MySQL?

  - by Josh Glover

  I have a data replication process that drops and recreates a few tables in a target database, then loads them up with data from a source database (running on another host, but that is immaterial to the question at hand). The target database does need primary keys and a few other indexes on its tables, but not during the data loading. I'm currently loading all of the data, then creating the indexes. However, index creation takes a pretty long time--30 minutes of my data loader's 5 and a half hour running time. My intuition tells me that creating the indexes at the end should be faster than creating them first, since the index would need to be rewritten with each insert. Can anyone tell me for sure which way is faster? FWIW, I'm running MySQL 5.1 with InnoDB tables.

  Read the article

• Managing rolling deployments in the cloud

  - by Josh Nankin

  Recently I've been experimenting with various cloud management tools like RightScale, Scalr, custom scripts for managing a variety of servers, each hosting several roles (app, db, load balancer, job queues, etc). The one thing I find lacking in most solutions is a way to do rolling deployments, i.e. running deployments sequentially across a number of servers with the same role. For instance, I dont want to build all of my webservers at the same time, as that will almost definitely result in some down time or 500s for my customers. I'd rather have one or two servers build at a time, while other servers are still available to handle requests. The other alternative is obviously to launch new servers that automatically update themselves on boot, but this isn't as cost effective, and most likely requires more time for the build to complete (it's faster to build on an existing server than to launch a new server and kill old ones). We've all heard of the big companies having the famous "push to build" button (companies like Twilio, Etsy, etc.) but it seems that they all have custom implementations of this. I'm not talking about a simple ssh-loop, clusterssh, or even an mcollective - I preferably want something with a nice simple interface that allows me to specify something like a RightScript or a Scalr script to run on a set of servers with a specific role, and it builds them sequentially. Does any one know of easy ways to get this done, or is this a candidate for a new open source project?

  Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >