Search Results

Search found 14282 results on 572 pages for 'performance counter'.

Page 14/572 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

  • Disk performance below expectations

    - by paulH
    this is a follow-up to a previous question that I asked (Two servers with inconsistent disk speed). I have a PowerEdge R510 server with a PERC H700 integrated RAID controller (call this Server B) that was built using eight disks with 3Gb/s bandwidth that I was comparing with an almost identical server (call this Server A) that was built using four disks with 6Gb/s bandwidth. Server A had much better I/O rates than Server B. Once I discovered the difference with the disks, I had Server A rebuilt with faster 6Gbps disks. Unfortunately this resulted in no increase in the performance of the disks. Expecting that there must be some other configuration difference between the servers, we took the 6Gbps disks out of Server A and put them in Server B. This also resulted in no increase in the performance of the disks. We now have two identical servers built, with the exception that one is built with six 6Gbps disks and the other with eight 3Gbps disks, and the I/O rates of the disks is pretty much identical. This suggests that there is some bottleneck other than the disks, but I cannot understand how Server B originally had better I/O that has subsequently been 'lost'. Comparative I/O information below, as measured by SQLIO. The same parameters were used for each test. It's not the actual numbers that are significant but rather the variations between systems. In each case D: is a 2 disk RAID 1 volume, and E: is a 4 disk RAID 10 volume (apart from the original Server A, where E: was a 2 disk RAID 0 volume). Server A (original setup with 6Gpbs disks) D: Read (MB/s) 63 MB/s D: Write (MB/s) 170 MB/s E: Read (MB/s) 68 MB/s E: Write (MB/s) 320 MB/s Server B (original setup with 3Gpbs disks) D: Read (MB/s) 52 MB/s D: Write (MB/s) 88 MB/s E: Read (MB/s) 112 MB/s E: Write (MB/s) 130 MB/s Server A (new setup with 3Gpbs disks) D: Read (MB/s) 55 MB/s D: Write (MB/s) 85 MB/s E: Read (MB/s) 67 MB/s E: Write (MB/s) 180 MB/s Server B (new setup with 6Gpbs disks) D: Read (MB/s) 61 MB/s D: Write (MB/s) 95 MB/s E: Read (MB/s) 69 MB/s E: Write (MB/s) 180 MB/s Can anybody suggest any ideas what is going on here? The drives in use are as follows: Dell Seagate F617N ST3300657SS 300GB 15K RPM SAS Dell Hitachi HUS156030VLS600 300GB 3.5 inch 15000rpm 6GB SAS Hitachi Hus153030vls300 300GB Server SAS Dell ST3146855SS Seagate 3.5 inch 146GB 15K SAS

    Read the article

  • Performance issues concurrently running MySQL and MS SQL Sever

    - by pacifika
    We're considering installing MySQL on the same database server that has been running MS SQL Server. From my research there are no technical issues running both concurrently, but I am worried that the performance will be affected. Is by default SQL Server set up to use all available memory for example? What should I look out for? Thanks

    Read the article

  • optimizing operating systems to provide maximum informix performance.

    - by Frank Developer
    Are there any Informix-specific guides for optimizing any operating system where an ifx engine is running? For example, in Linux, strip-down to a bare minimum all unecessary binaries, daemons, utilities, tune kernel parameters, optimize raw and cooked devices (hdparm). Someday, maybe, informix can create its own proprietary PICK-like O/S. The general idea is for the OS where ifx sits on have the smallest footprint, lowest overhead impact on ifx and provide optimized ifx performance.

    Read the article

  • Which is faster? 4x10k SAS Drives in RAID 10 or 3x15k SAS Drives in RAID 5?

    - by Jenkz
    I am reviewing quote for a server upgrade. (RHEL). The server will have both Apache and MySQL on it, but the reason for upgrade is to increase DB performance. CPU has been upgraded massively, but I know that disk speed is also a factor. So RAID 10 is faster performance than RAID 5, but how much difference does the drive speed make? (The 15k discs in the RAID 5 config is at the top of my budget btw, hence not considdering 4x15k discs in RAID 10, which I assume would be the optimum.)

    Read the article

  • Linux's best filesystem to work with 10000's of files without overloading the system I/O

    - by mhambra
    Hi all. It is known that certain AMD64 Linuxes are subject of being unresponsive under heavy disk I/O (see Gentoo forums: AMD64 system slow/unresponsive during disk access (Part 2)), unfortunately have such one. I want to put /var/tmp/portage and /usr/portage trees to a separate partition, but what FS to choose for it? Requirements: * for journaling, performance is preffered over safe data read/write operations * optimized to read/write 10000 of small files Candidates: * ext2 without any journaling * BtrFS In Phoronix tests, BtrFS had demonstrated a good random access performance (fat better than XFS thereby it may be less CPU-aggressive). However, unpacking operation seems to be faster with XFS there, but it was tested that unpacking kernel tree to XFS makes my system to react slower for 51% disregard of any renice'd processes and/or schedulers. Why no ReiserFS? Google'd this (q: reiserfs ext2 cpu): 1 Apr 2006 ... Surprisingly, the ReiserFS and the XFS used significantly more CPU to remove file tree (86% and 65%) when other FS used about 15% (Ext3 and ... Is it same now?

    Read the article

  • Performance issues concurrently running MySQL and SQL Sever

    - by pacifika
    We're considering installing MySQL on the same database server that has been running SQL Server. From my research there are no technical issues running both concurrently, but I am worried that the performance will be affected. Is by default SQL Server set up to use all available memory for example? What should I look out for? Thanks

    Read the article

  • Performance monitor visualization tool

    - by MK
    I'm looking for a tool to display data from performance monitor counters. I'm looking for something that would be visually appealing (look like a dashboard) and it should be able to aggregate (sum up) over multiple counters. No thresholds/alarming needed, we are using Nagios for that.

    Read the article

  • Why does Process Explorer cause highly targeted failure of some applications / basic UI functions in a high-power EC2 Windows instance?

    - by Dan Nissenbaum
    Update: I have determined that Process Explorer itself - the program I am using to debug a performance issue - seems to be the cause of the issue. See note, with updated question, at end. I am running a high-power (cc2.8xlarge) Amazon AWS EC2 Windows instance off of a boot EBS volume, provisioned at 2500 PIOPS, which was created from a snapshot of a previous boot volume. My purpose with the instance is to use it as a development workstation with many developer tools installed, such as Visual Studio, a local XAMPP stack, etc. I have upwards of 40 programs installed on the machine. The usability of the instance as a development machine often works quite well. The RDP lag is adequately small. I have used it for hours on end without problems for some of my most intense development tasks. As a result, I have just purchased a reserved instance, and I opted to rebuild my development machine starting from scratch with a Windows Server 2012 AMI. After having installed all of my desired/required applications for development over this past week, again the machine seems to often work well and I have worked for up to an hour at a time without problems doing heavy development work. However, I continue to run into catastrophic OS usability issues that may prevent me from being able to rely on this machine as a development machine. I would like to track down the source of the problem, if there is an easily identifiable source. (Update: I have tracked down the source to be Process Explorer, the very program I was using to debug the problem. See update at end.) The issues are as follows. (These are some primary examples) Some applications, after a period of adequate responsiveness, suddenly begin to respond very, very slowly to basic user interface actions such as clicking on menus and pressing Ctrl-Tab to switch between open documents. Two examples are UltraEdit and PhpEd. It typically takes ~2 seconds for a menu to appear, and ~4 seconds to switch between open documents. Additionally, insertion point motion in the editor is lagged by upwards of ~2 seconds. Process Explorer, which I am using to help debug the problem, seems to run acceptably for a couple of minutes, but on multiple occasions Process Explorer itself hangs completely. It hangs at the same time as the problems noted above. When it hangs, it is 100% unresponsive. Clicking on its taskbar icon neither causes it to come to the top or go behind, and its viewable area is filled with nothing but a region partially containing pure white and partially containing incomplete windows widgets that are unreadable, and that never change. Waiting 10 minutes does not clear the problem. Attempting to force-quit Process Explorer by right-clicking on its taskbar icon and choosing "Close Window" takes about 5 full minutes to exit (Process Explorer itself can't be used to exit Process Explorer, and it is registered as a Task Manager substitute). Other programs work just fine during this time. For example, Chrome tabs flip very quickly back and forth, menus pop open instantly, web pages load quickly, and typing in forms/web applications inside the browser works promptly. Another example of an application that works crisply is Filemaker - its menus open instantly, and switching views in this application occurs promptly. Other applications also work without issue. Also, switching between applications occurs promptly as well. It is only a handful of applications that exhibit the problem, with some primary examples given above. At first I thought that EBS IOPS might be a problem. Therefore, I ran Performance Monitor, and watched the "Disk Transfers/sec" monitor in real time. At no point did this measure come anywhere close to hitting the 2500 PIOPS provisioned for the EBS volume. The RAM was also well under the limit (~10 GB used out of 60 GB). I did notice that one CPU core (out of 32 logical cores) was fully thrashing at 100% (i.e., ~3.1%) during the problematic periods. This seems to indicate that a single CPU core is handling the menus / flipping between open documents (for some applications only) / managing the Process Explorer user interface, and that this single core was hosed for some reason during the problematic periods. Also note that I have a desktop workstation (Windows 7) that I also use as a development machine, via a remote connection, with a nearly identical set of programs installed, and this desktop workstation does not exhibit any of the problems I've discussed above. I have been using it heavily for well over a year now. Any suggestions regarding either the source of the problem, or steps I might take to investigate the source of the problem, would be appreciated. Thanks. Note: After extensive testing & investigation, I have noticed that when I quit Process Explorer, the problem vanishes and the system performance returns to normal, and then reappears quickly when I run Process Explorer again (note: again, the performance problems only appear for a subset of applications - other applications work perfectly fine during the same period). My question is therefore (thankfully) more specific: Why does Process Explorer cause highly targeted failure of some applications (including itself) and basic UI functions, in a high-power EC2 Windows instance?

    Read the article

  • How to increase performance of Remote Desktop

    - by H B K
    How can I increase performance of Remote Desktop on windows XP sp3? A better network connection is not an option, this is for at work. I have suggested a network upgrade to my boss and it is not in the budget right now, but I need to access my home computer and right now it is somewhat unusable.

    Read the article

  • Further Performance Tuning on Medium SharePoint Farm?

    - by elorg
    I figured I would post this here, since it may be related more to the server configuration than the SharePoint configuration or a combination of both? I'm open for ideas to try, or even feedback on things that maybe have been configured incorrectly as far as performance is concerned. We have a medium MOSS 2007 install prepped and ready for receiving the WSS 2003 data to upgrade. The environment was originally architected by a previous coworker, and I have since added a few configuration modifications to assist with performance before we finally performed the install. When testing the new site collections & SharePoint install (no actual data yet), things seemed a bit slow. I had assumed that it was because I was accessing it remotely. Apparently the client is still experiencing this and it is unacceptably slow. 1 SQL Server running SQL Server 2008 2x SharePoint WFEs - hosting queries (no index) 1x SharePoint Index - hosting index (no queries) MOSS 2007 installed and patched up through December '09 on WFEs & Index All 4 servers are VMs, should have more than sufficient disk space & RAM (don't recall at the moment), and are running Windows Server 2008 - everything is 64-bit. The WFEs have Windows NLB configured, with a DNS name & IP for the NLB cluster. Single NIC on each server (virtual, since VMWare). The Index server is configured as a WFE (outside of the NLB cluster) so that it can index itself and replicate the indexes to the WFEs that will serve the queries. Everything is configured & working properly - it just takes a minute or two to load a page on the local LAN. The client is still using their old portal (we haven't started the migration/upgrade just yet) so there's virtually no data or users. We need to either further tune the configuration, or fix anything that may have been configured incorrectly which is causing this slowness? I've already reviewed & taken into account everything that I could find that was relevant before we even started the install. Does anyone have ideas or pointers? Perhaps there's something that I've missed?

    Read the article

  • Load and performance testing for webapps with JavaScript support

    - by MrG
    Years ago I used OpenSTA to perform load and performance tests. Unfortunately it doesn't support JavaScript, which is a requirement this time. But I remember that it offered great recording possibilities which enabled us to quickly create new test scripts. Please let me which tools you recommend. Free tools are clearly preferred ;)

    Read the article

  • Windows 2003 :: Performance Monitoring :: Simple/Stupid Tutorial

    - by BSI Support
    I have a half dozen front-end servers all running IIS 6.0-based/hosted applications. (primary .NET 2.0 web apps.) Basically, I'd like to take some basic performance data from each one, through such into a spreadsheet, and compare. CPU load, RAM load, whatever... If anyone can point out a very simple/stupid "here's how you do that" type of tutorial, that would be wonderful.

    Read the article

  • Steps to diagnose performance bottlenecks on Mac OS X

    - by Dave Cahill
    If you wanted to track down performance issues on a machine running Mac OS X and find out what was causing slowdowns, which command-line or graphical tools would you use, and how would you use them? I'm interested in advice on the best tools, and explanations of how to use them - when a machine slows down or freezes up, I'd like to be able to dig down and understand what's going on, memory / disk / CPU-wise. Thanks.

    Read the article

  • How to figure out disks performance in Xen?

    - by cpt.Buggy
    So, I have a Dell R710 with PERC 6/i Integrated and 6 450Gb Seagate 15k SAS disks in RAID10, I have 30 Xen vps working on it. Now I need to deploy second server with same hardware for same tasks and I want to figure out maybe it's a good idea to use RAID5 instead of RAID10 because we have a lot of "free" memory on first server and not so much "free space". How do I find out disks performance on first server and find out could I move it to RAID5 without slowing down of whole system?

    Read the article

  • Ruby Performance Profiling

    - by JustSmith
    I'm developing some code that calls another function and then sends out its response. If the said function takes to long i want to record this. Are there any light weight FREE performance profiling tools for Ruby, not on rails, that can do this? I'm even open to any solution that is accurate.

    Read the article

  • "Email This" button with sideways counter

    - by aendrew
    I've been asked to build a design that has a "share this" area like below: I've built every aspect except the Email part of it -- any idea how best to do that? I've found http://getmailcounter.com/, but that displays a counter above. I'd personally just do a link, but it seems they're wanting some sort of analytics built in... Failing that, does anyone know of some sort of sharing system that looks like that and has all of those options? I'd just use AddThis, but its designs don't look very close to that... Thanks! Related: How to implement an email this link button

    Read the article

  • jQuery: Counter, Tricky problem with effects for brainy people.

    - by Marius
    Hello there! I made this counter that I think is cool because it only makes visible changes to the numbers being changed between each time it is triggered. This is the code // counter $('a').click(function(){ var u = ''; var newStr = ''; $('.counter').each(function(){ var len = $(this).children('span').length; $(this).children('span').each(function(){ u = u + $(this).text(); }); v = parseInt(u) + 1; v = v + ''; for (i=v.length - 1; i >= 0; i--) { if (v.charAt(i) == u.charAt(i)) { break; } } slce = len - (v.length - (i + 1)) updates = $(this).children('span').slice(slce); $(updates).fadeTo(100,0).delay(100).each(function(index){ f = i + 1 + index; $(this).text(v.charAt(f)); }).fadeTo(100,1); }); }); Markup: <span class="counter"> <span></span><span></span><span></span><span></span><span></span><span></span><span style="margin-right:4px;">9</span><span>9</span><span>9</span><span>9</span> </span> <a href="">Add + 1</a> The problem is that I previously used queue() function to delay() $(this).text(v.charAt(f)); by 100ms, (without queue the text()-function would not be delayed because it isnt in the fx catergory) so that the text would be updated before the object had faded to opacity = 0. That would look stupid. When adding multiple counters, only one of the counters would count. When removing the queue function, both counters would work, but as you can imagine, the delay of the text() would be gone (as it isnt fx-category). It is probably a bit tricky to make out how I can have multiple counters, and still delay the text()-function by 100ms, but I was hoping there is somebody here with spare brain capacity for these things ;) You can see a (NSFW) problem demo here: Just look underneath the sharing icons and you will notice that the text changes WHILE the objects fade out. Looking for some help to sove this problem. I would like to call the text() function once the text has faded to opacity 0, then fade in once the text() has executed. Thank you for your time.

    Read the article

  • how to implement a counter in label which decrements every time page is loaded in asp.net(vb)?

    - by Parth
    how to implement a counter in label which decrements every time page is loaded in asp.net(vb)? It would be better if that counter value is accessed from and updated into database.. I've tried this on buttonclick but the value is reset automatically to intial value everytime as the button is insert and page is reloaded Protected Sub InsertButton_Click(ByVal sender As Object, ByVal e As System.EventArgs) Dim entries As Label = FindControl("label1") entries.Text = entries.Text - 1 End Sub

    Read the article

  • problem with update the counter value

    - by Edan
    Hello, I having problem to update the counter (integer value). this is the definitions of the class: public class Item_Actions { private final int MAX_ITEMS = 100; private Item myItem[]; private int counter; public Item_Actions() { myItem = new Item[MAX_ITEMS]; counter++; } //Constructor add item into the menu (Description, type & price of Item) public void addItem(Item itm) { myItem[counter] = itm; counter++; }....... Now everytime I call the addItem constructor from another class, the counter always stays on zero. What causing it and how do I save the data inside? thanks

    Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >