Search Results

Search found 40420 results on 1617 pages for 'power line networking'.

Page 14/1617 | < Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >

• How to permanently save power options in windows 7

  - by Ieyasu Sawada

  How can I set the hard disk to never turn off permanently?And the sleep to never, together with the hibernate. Because the options resets to their default values when I turn off, log off or restart my computer. I am using granola on my laptop and it is set to lowest speed. When I restart it turns to full power again. Does it have something to do with the power options resetting to their default values?

  Read the article

• Raid 5 and Power Supply damage?

  - by Tronic

  Hi. Because I build a RAID 5 atm, I wanted to ask, what would happen if the server with a raid 5 in it (like 4-5 hdds) would have a power supply damage? Can I just switch the power supply and my data is safe and backup again or will there be a raid damage as well? Thanks in advance. Regards.

  Read the article

• Power supply for HP Workstation xw4100

  - by Nathan Adams

  Does anyone know if the HP Workstation xw4100 takes a "special" power supply? I know there was a time when everyone was using their own PSs with different pinouts, but I was under the impression that enough people complained and all the companies switched to standard power supplies.

  Read the article

• Power on from standby with wireless keyboard

  - by ULTRA_POROV

  S3 standby state. Set power-on by usb device in bios. Enabled standby power-on in device manager on the keyboard. No effect. Any ideas? Is it possible?

  Read the article

• MB with CPU and power supply - can be turned on but not off

  - by COcodrilo

  Hi, Not sure whether this question belongs here, I hope so. I have just bought a motherboard and CPU. I have installed the CPU, cooler and connected to CPUFAN on the MB. I have plugged the power supply to MB and the cable from "ON" button to pins named "PWR" and the LEDs. However when I turn on the PC, both HDD and POWER leds are continously on and the PC cannot be turned out. What could I be missing?

  Read the article

• MB with CPU and power supply - can be turned on but not off [closed]

  - by COcodrilo

  Hi, Not sure whether this question belongs here, I hope so. I have just bought a motherboard and CPU. I have installed the CPU, cooler and connected to CPUFAN on the MB. I have plugged the power supply to MB and the cable from "ON" button to pins named "PWR" and the LEDs. However when I turn on the PC, both HDD and POWER leds are continously on and the PC cannot be turned out. What could I be missing?

  Read the article

• Reason behind system power usage?

  - by user28565

  Hi, when the number of applications running in a pc increases, the power consumed by the PC is also increasing. Is this correct? I think the reason behind this is CPU. Please let me know what role the CPU plays for more power usage. Thanks, Kavi

  Read the article

• How Can I Test My Computer’s Power Supply?

  - by Jason Fitzpatrick

  You’re concerned your computer troubles stem from a failing (or outright fried) power supply unit. How can you test the unit to be sure that it’s the source of your hardware headaches? Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-driven grouping of Q&A web sites. The Question SuperUser reader Sam Hoice has some PSU concerns: My computer powered off the other day on its own, and now when I push the power button, nothing happens. My assumption would naturally be that the power supply is done (possibly well done) but is there any good way to test this before I buy a new one? How can Sam test things without damaging his current computer or other hardware?   The Answer SuperUser contributor Grant writes: Unplug the power supply from any of the components inside the computer (or just remove it from the computer completely). USE CAUTION HERE (Though you’d only be shocked with a max of 24 volts) Plug the power supply into the wall. Find the big 24-ish pin connector that connects to the motherboard. Connect the GREEN wire with the adjacent BLACK wire. The power supply’s fan should start up. If it doesn’t then it’s dead. If the fan starts up, then it could be the motherboard that’s dead. You can use a multimeter to check if there is power output from the power supply. Adrien offers a solution for readers who may not be comfortable jamming wires into their power supply unit’s MOBO connector: Most well-stocked geek-stores sell a “power-supply tester” that has all the appropriate connectors to plug each part of your PSU into, with spiffy LEDs indicating status of the various rails, connectors for IDE/SATA/floppy power cables, etc. They run ~$20 US. With a little careful shopping you can even find a highly-rated PSU tester for a measly $6. Have something to add to the explanation? Sound off in the the comments. Want to read more answers from other tech-savvy Stack Exchange users? Check out the full discussion thread here.     

  Read the article

• debian lenny xen bridge networking problem

  - by Sasha

  DomU isn't talking to the world, but it talks to Dom0. Here are the tests that I made: Dom0 (external networking is working): ping 188.40.96.238 #Which is Domu's ip PING 188.40.96.238 (188.40.96.238) 56(84) bytes of data. 64 bytes from 188.40.96.238: icmp_seq=1 ttl=64 time=0.092 ms DomU: ping 188.40.96.215 #Which is Dom0's ip PING 188.40.96.215 (188.40.96.215) 56(84) bytes of data. 64 bytes from 188.40.96.215: icmp_seq=1 ttl=64 time=0.045 ms ping 188.40.96.193 #Which is the gateway - fail PING 188.40.96.193 (188.40.96.193) 56(84) bytes of data. ^C --- 188.40.96.193 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1013ms The system is debian lenny with a normal setup. Here is my configs: uname -a Linux green0 2.6.26-2-xen-686 #1 SMP Wed Aug 19 08:47:57 UTC 2009 i686 GNU/Linux cat /etc/xen/green1.cfg |grep -v '#' kernel = '/boot/vmlinuz-2.6.26-2-xen-686' ramdisk = '/boot/initrd.img-2.6.26-2-xen-686' memory = '2000' root = '/dev/xvda2 ro' disk = [ 'file:/home/xen/domains/green1/swap.img,xvda1,w', 'file:/home/xen/domains/green1/disk.img,xvda2,w', ] name = 'green1' vif = [ 'ip=188.40.96.238,mac=00:16:3E:1F:C4:CC' ] on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' ifconfig eth0 Link encap:Ethernet HWaddr 00:24:21:ef:2f:86 inet addr:188.40.96.215 Bcast:188.40.96.255 Mask:255.255.255.192 inet6 addr: fe80::224:21ff:feef:2f86/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3296 errors:0 dropped:0 overruns:0 frame:0 TX packets:2204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:262717 (256.5 KiB) TX bytes:330465 (322.7 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) peth0 Link encap:Ethernet HWaddr 00:24:21:ef:2f:86 inet6 addr: fe80::224:21ff:feef:2f86/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:3407 errors:0 dropped:657431448 overruns:0 frame:0 TX packets:2291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:319941 (312.4 KiB) TX bytes:338423 (330.4 KiB) Interrupt:16 Base address:0x8000 vif2.0 Link encap:Ethernet HWaddr fe:ff:ff:ff:ff:ff inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:151 errors:0 dropped:33 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1164 (1.1 KiB) TX bytes:20974 (20.4 KiB) ip a s 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: peth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000 link/ether 00:24:21:ef:2f:86 brd ff:ff:ff:ff:ff:ff inet6 fe80::224:21ff:feef:2f86/64 scope link valid_lft forever preferred_lft forever 4: vif0.0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff 5: veth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 6: vif0.1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff 7: veth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 8: vif0.2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff 9: veth2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 10: vif0.3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff 11: veth3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 12: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 00:24:21:ef:2f:86 brd ff:ff:ff:ff:ff:ff inet 188.40.96.215/26 brd 188.40.96.255 scope global eth0 inet6 fe80::224:21ff:feef:2f86/64 scope link valid_lft forever preferred_lft forever 14: vif2.0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 32 link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff inet6 fe80::fcff:ffff:feff:ffff/64 scope link valid_lft forever preferred_lft forever brctl show bridge name bridge id STP enabled interfaces eth0 8000.002421ef2f86 no peth0 vif2.0 ip r l Dom0: 188.40.96.192/26 dev eth0 proto kernel scope link src 188.40.96.215 default via 188.40.96.193 dev eth0 DomU: 188.40.96.192/26 dev eth0 proto kernel scope link src 188.40.96.238 default via 188.40.96.193 dev eth0

  Read the article

• alert(line) alerts 'ac' and typeof(line) is 'string', but charAt is not a function

  - by Delirium tremens

  alert(line) alerts 'ac' typeof(line) is 'string' When I run line.charAt(0), charAt is not a function. When line is 'http://www.google.com/', it works, I think it's the UTF-8 encoding of the file that I opened... How to make charAt work with UTF-8? UPDATED: http://mxr.mozilla.org/mozilla-central/source/netwerk/dns/src/effective_tld_names.dat?raw=1 is in my extension's chrome folder as effective_tld_names.dat To run the code: authority = 'orkut.com.br'; lines = sc_geteffectivetldnames(); lines = sc_preparetouse(lines); domainname = sc_extractdomainname(authority, lines); The code: function sc_geteffectivetldnames () { var MY_ID = "[email protected]"; var em = Components.classes["@mozilla.org/extensions/manager;1"]. getService(Components.interfaces.nsIExtensionManager); var file = em.getInstallLocation(MY_ID).getItemFile(MY_ID, "chrome/effective_tld_names.dat"); var istream = Components.classes["@mozilla.org/network/file-input-stream;1"]. createInstance(Components.interfaces.nsIFileInputStream); istream.init(file, 0x01, 0444, 0); istream.QueryInterface(Components.interfaces.nsILineInputStream); var line = {}, lines = [], hasmore; do { hasmore = istream.readLine(line); lines.push(line.value); } while(hasmore); istream.close(); return lines; } function sc_preparetouse(lines) { lines = sc_notcomment(lines); lines = sc_notempty(lines); return lines; } function sc_notcomment(lines) { var line; var commentre; var matchedcomment; var replacedlines; replacedlines = new Array(); var i = 0; while (i < lines.length) { line = lines[i]; commentre = new RegExp("^//", 'i'); matchedcomment = line.match(commentre); if(matchedcomment) { lines.splice(i, 1); } else { i++; } } return lines; } function sc_notempty(lines) { var line; var emptyre; var matchedempty; var replacedlines; replacedlines = new Array(); var i = 0; while (i < lines.length) { line = lines[i]; emptyre = new RegExp("^$", 'i'); matchedempty = line.match(emptyre); if(matchedempty) { lines.splice(i, 1); } else { i++; } } return lines; } function sc_extractdomainname(authority, lines) { for (var i = 0; i < lines.length; i++) { line = lines[i]; alert(line); alert(typeof(line)); if (line.chatAt(0) == '*') { alert('test1'); continue; } if (line.chatAt(0) == '!') { alert('test2'); line.chatAt(0) = ''; } alert('test3'); checkline = sc_checknotasteriskline(authority, line); if (checkline) { domainname = checkline; } } if (!domainname) { for (var i = 0; i < lines.length; i++) { line = lines[i]; alert(line); if (line.chatAt(0) != '*') { continue; alert('test4'); } if (line.chatAt(0) == '!') { line.chatAt(0) = ''; alert('test5'); } alert('test6'); checkline = sc_checkasteriskline(authority, line); if (checkline) { domainname = checkline; } } } return domainname; } It alerts 'ac', then 'string', then nothing.

  Read the article

• alert(line) alerts 'ac' and typeof(line) is 'string', but charAt is not a function

  - by Delirium tremens

  alert(line) alerts 'ac' typeof(line) is 'string' When I run line.charAt(0), charAt is not a function. When line is 'http://www.google.com/', it works, I think it's the UTF-8 encoding of the file that I opened... How to make charAt work with UTF-8? UPDATED: http://mxr.mozilla.org/mozilla-central/source/netwerk/dns/src/effective_tld_names.dat?raw=1 is in my extension's chrome folder as effective_tld_names.dat To run the code: authority = 'orkut.com.br'; lines = sc_geteffectivetldnames(); lines = sc_preparetouse(lines); domainname = sc_extractdomainname(authority, lines); The code: function sc_geteffectivetldnames () { var MY_ID = "[email protected]"; var em = Components.classes["@mozilla.org/extensions/manager;1"]. getService(Components.interfaces.nsIExtensionManager); var file = em.getInstallLocation(MY_ID).getItemFile(MY_ID, "chrome/effective_tld_names.dat"); var istream = Components.classes["@mozilla.org/network/file-input-stream;1"]. createInstance(Components.interfaces.nsIFileInputStream); istream.init(file, 0x01, 0444, 0); istream.QueryInterface(Components.interfaces.nsILineInputStream); var line = {}, lines = [], hasmore; do { hasmore = istream.readLine(line); lines.push(line.value); } while(hasmore); istream.close(); return lines; } function sc_preparetouse(lines) { lines = sc_notcomment(lines); lines = sc_notempty(lines); return lines; } function sc_notcomment(lines) { var line; var commentre; var matchedcomment; var replacedlines; replacedlines = new Array(); var i = 0; while (i < lines.length) { line = lines[i]; commentre = new RegExp("^//", 'i'); matchedcomment = line.match(commentre); if(matchedcomment) { lines.splice(i, 1); } else { i++; } } return lines; } function sc_notempty(lines) { var line; var emptyre; var matchedempty; var replacedlines; replacedlines = new Array(); var i = 0; while (i < lines.length) { line = lines[i]; emptyre = new RegExp("^$", 'i'); matchedempty = line.match(emptyre); if(matchedempty) { lines.splice(i, 1); } else { i++; } } return lines; } function sc_extractdomainname(authority, lines) { for (var i = 0; i < lines.length; i++) { line = lines[i]; alert(line); alert(typeof(line)); if (line.chatAt(0) == '*') { alert('test1'); continue; } if (line.chatAt(0) == '!') { alert('test2'); line.chatAt(0) = ''; } alert('test3'); checkline = sc_checknotasteriskline(authority, line); if (checkline) { domainname = checkline; } } if (!domainname) { for (var i = 0; i < lines.length; i++) { line = lines[i]; alert(line); if (line.chatAt(0) != '*') { alert('test4'); continue; } if (line.chatAt(0) == '!') { alert('test5'); line.chatAt(0) = ''; } alert('test6'); checkline = sc_checkasteriskline(authority, line); if (checkline) { domainname = checkline; } } } return domainname; } It alerts 'ac', then 'string', then nothing.

  Read the article

• Why is my Internet connection randomly dropping?

  - by Jeanno

  Ever since I have installed 12.04 (clean install not an upgrade), i have been having a drop in the Internet connection. The drop in the connection can be anything from 15 seconds to about 3 mins, and then the connection comes back. This behaviour happens while I am actively browsing the Internet, or if I wake up the computer and open Firefox (sometimes I have connection and sometimes I don't) . Please note that when the internet connection is on, it is not slow (as speedtest.net results show) In the beginning, I thought it was a problem with the driver r8169 for my RTL8111/8168B Ethernet card, so I downloaded the r8168 from Realtek website, followed the detailed instructions (blacklisted r8169, changed the file to '.bsh' ...), but still the same problem persisted. So I switched to a wireless connection, and I got the same problem with internet connection dropping randomly. Any ideas? Thanks in advance Output from 'lspci -v' Code: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: f8000000-fa0fffff Prefetchable memory behind bridge: 00000000d0000000-00000000dbffffff Capabilities: [88] Subsystem: Dell Device 04a7 Capabilities: [80] Power Management version 3 Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [a0] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [140] Root Complex Link Kernel driver in use: pcieport Kernel modules: shpchp 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: f4000000-f60fffff Prefetchable memory behind bridge: 00000000c0000000-00000000cbffffff Capabilities: [88] Subsystem: Dell Device 04a7 Capabilities: [80] Power Management version 3 Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [a0] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [140] Root Complex Link Kernel driver in use: pcieport Kernel modules: shpchp 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at f6108000 (64-bit, non-prefetchable) [size=16] Capabilities: [50] Power Management version 3 Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+ Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI]) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at f6107000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 53 Memory at f6100000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Memory behind bridge: fa400000-fa4fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Prefetchable memory behind bridge: 00000000dc100000-00000000dc1fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fa300000-fa3fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fa200000-fa2fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI]) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at f6106000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation P67 Express Chipset Family LPC Controller (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> Kernel modules: iTCO_wdt 00:1f.2 RAID bus controller: Intel Corporation 82801 SATA Controller [RAID mode] (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 42 I/O ports at f070 [size=8] I/O ports at f060 [size=4] I/O ports at f050 [size=8] I/O ports at f040 [size=4] I/O ports at f020 [size=32] Memory at f6105000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [70] Power Management version 3 Capabilities: [a8] SATA HBA v1.0 Capabilities: [b0] PCI Advanced Features Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) Subsystem: Dell Device 04a7 Flags: medium devsel, IRQ 5 Memory at f6104000 (64-bit, non-prefetchable) [size=256] I/O ports at f000 [size=32] Kernel modules: i2c-i801 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0dc5 (rev a1) (prog-if 00 [VGA controller]) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at f8000000 (32-bit, non-prefetchable) [size=16M] Memory at d0000000 (64-bit, prefetchable) [size=128M] Memory at d8000000 (64-bit, prefetchable) [size=32M] I/O ports at e000 [size=128] Expansion ROM at fa000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb 01:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at fa080000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 02:00.0 VGA compatible controller: NVIDIA Corporation Device 0dc5 (rev a1) (prog-if 00 [VGA controller]) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f4000000 (32-bit, non-prefetchable) [size=32M] Memory at c0000000 (64-bit, prefetchable) [size=128M] Memory at c8000000 (64-bit, prefetchable) [size=64M] I/O ports at d000 [size=128] Expansion ROM at f6000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb 02:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at f6080000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 03:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30 [XHCI]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fa400000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] Latency Tolerance Reporting Kernel driver in use: xhci_hcd 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 51 I/O ports at c000 [size=256] Memory at dc104000 (64-bit, prefetchable) [size=4K] Memory at dc100000 (64-bit, prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Endpoint, MSI 01 Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Capabilities: [d0] Vital Product Data Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Capabilities: [160] Device Serial Number 03-00-00-00-68-4c-e0-00 Kernel driver in use: r8168 Kernel modules: r8168 05:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller (rev 01) (prog-if 10 [OHCI]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at fa300000 (64-bit, non-prefetchable) [size=2K] I/O ports at b000 [size=256] Capabilities: [50] Power Management version 3 Capabilities: [80] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [98] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [130] Device Serial Number 00-10-dc-ff-ff-cf-56-1a Kernel driver in use: firewire_ohci Kernel modules: firewire-ohci 06:00.0 SATA controller: JMicron Technology Corp. JMB362 SATA Controller (rev 10) (prog-if 01 [AHCI 1.0]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 19 I/O ports at a040 [size=8] I/O ports at a030 [size=4] I/O ports at a020 [size=8] I/O ports at a010 [size=4] I/O ports at a000 [size=16] Memory at fa210000 (32-bit, non-prefetchable) [size=512] Capabilities: [8c] Power Management version 3 Capabilities: [50] Express Legacy Endpoint, MSI 00 Kernel driver in use: ahci Note that my wireless card is not showing, I have the Ralink 3390 card (which apparently does not show up on Ubuntu for some reason), however I am able to connect to wireless network and connect to the internet (when it is working)

  Read the article

• Static background noise while using new headset Ubuntu 13.04

  - by ThundLayr

  Today I bought a new gaming headset (Gx-Gaming Lychas), and when I tried to record some gameplay-comentary I noticed that there always is a static background noise, I just recorded an example so you guys can listen it (no downloaded needed): http://www47.zippyshare.com/v/65167832/file.html I'm using Kubuntu 13.04 and Kernel version is 3.8.0-19, my laptop is an Acer Travelmate 5760Z, I tried tons of configurations on Alsamixer and none of them made result, I really need to get this working so any kind of help will be very aprecciated. cat /proc/asound/cards: 0 [PCH ]: HDA-Intel - HDA Intel PCH HDA Intel PCH at 0xc6400000 irq 44 cat /proc/asound/card0/codec#0 Codec: Conexant CX20588 Address: 0 AFG Function Id: 0x1 (unsol 1) Vendor Id: 0x14f1506c Subsystem Id: 0x10250574 Revision Id: 0x100003 No Modem Function Group found Default PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A State of AFG node 0x01: Power states: D0 D1 D2 D3 D3cold CLKSTOP EPSS Power: setting=D0, actual=D0 GPIO: io=4, o=0, i=0, unsolicited=1, wake=0 IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 Node 0x10 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L Control: name="Headphone Playback Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Control: name="Headphone Playback Switch", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Device: name="CX20588 Analog", type="Audio", device=0 Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-Out vals: [0x4a 0x4a] Converter: stream=8, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x11 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L Control: name="Speaker Playback Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Control: name="Speaker Playback Switch", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-Out vals: [0x80 0x80] Converter: stream=8, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x12 [Audio Output] wcaps 0x611: Stereo Digital Converter: stream=0, channel=0 Digital: Digital category: 0x0 IEC Coding Type: 0x0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x5]: PCM AC3 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x13 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out Control: name="Beep Playback Volume", index=0, device=0 ControlAmp: chs=1, dir=Out, idx=0, ofs=0 Control: name="Beep Playback Switch", index=0, device=0 ControlAmp: chs=1, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x07, nsteps=0x07, stepsize=0x0f, mute=0 Amp-Out vals: [0x00] Node 0x14 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Control: name="Capture Volume", index=0, device=0 ControlAmp: chs=3, dir=In, idx=0, ofs=0 Control: name="Capture Switch", index=0, device=0 ControlAmp: chs=3, dir=In, idx=0, ofs=0 Device: name="CX20588 Analog", type="Audio", device=0 Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x50 0x50] [0x80 0x80] [0x80 0x80] [0x80 0x80] Converter: stream=4, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x15 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] Converter: stream=0, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x16 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] Converter: stream=0, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x17 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out Control: name="Mic Boost Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0 Amp-Out vals: [0x04 0x04] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x1a 0x1b* 0x1d 0x1e Node 0x18 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0 Amp-Out vals: [0x00 0x00] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x1a* 0x1b 0x1d 0x1e Node 0x19 [Pin Complex] wcaps 0x400581: Stereo Control: name="Headphone Jack", index=0, device=0 Pincap 0x0000001c: OUT HP Detect Pin Default 0x04214040: [Jack] HP Out at Ext Right Conn = 1/8, Color = Green DefAssociation = 0x4, Sequence = 0x0 Pin-ctls: 0xc0: OUT HP Unsolicited: tag=01, enabled=1 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1a [Pin Complex] wcaps 0x400481: Stereo Control: name="Internal Mic Phantom Jack", index=0, device=0 Pincap 0x00001324: IN Detect Vref caps: HIZ 50 80 Pin Default 0x90a70130: [Fixed] Mic at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0x3, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x24: IN VREF_80 Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x1b [Pin Complex] wcaps 0x400581: Stereo Control: name="Mic Jack", index=0, device=0 Pincap 0x00011334: IN OUT EAPD Detect Vref caps: HIZ 50 80 EAPD 0x0: Pin Default 0x04a19020: [Jack] Mic at Ext Right Conn = 1/8, Color = Pink DefAssociation = 0x2, Sequence = 0x0 Pin-ctls: 0x24: IN VREF_80 Unsolicited: tag=02, enabled=1 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1c [Pin Complex] wcaps 0x400581: Stereo Pincap 0x00000014: OUT Detect Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1d [Pin Complex] wcaps 0x400581: Stereo Pincap 0x00010034: IN OUT EAPD Detect EAPD 0x0: Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1e [Pin Complex] wcaps 0x400481: Stereo Pincap 0x00000024: IN Detect Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Control: name="Speaker Phantom Jack", index=0, device=0 Pincap 0x00000010: OUT Pin Default 0x92170110: [Fixed] Speaker at Int Front Conn = Analog, Color = Unknown DefAssociation = 0x1, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10 0x11* Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 1 0x12 Node 0x21 [Audio Output] wcaps 0x611: Stereo Digital Converter: stream=0, channel=0 Digital: Digital category: 0x0 IEC Coding Type: 0x0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x5]: PCM AC3 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x22 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 1 0x21 Node 0x23 [Pin Complex] wcaps 0x40040b: Stereo Amp-In Amp-In caps: ofs=0x00, nsteps=0x04, stepsize=0x2f, mute=0 Amp-In vals: [0x00 0x00] Pincap 0x00000020: IN Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x24 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In Amp-In caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10 0x11 Node 0x25 [Vendor Defined Widget] wcaps 0xf00000: Mono

  Read the article

• Optimal Networking Setup for a 2-Story unit?

  - by user29336

  I am moving into a 4 bedroom two-story unit. It’s roughly 2,200 sq ft. I want absolute max throughput possible to be achieved in all focal points. We’re all in internet related industries. Between gaming and web-development latency and throughput are major factors for us. Here’s our main focal points: 1) Garage (office). downstairs 2) Each bedroom x4. upstairs 3) Living room. downstairs The fastest line we can get is Comcast 50mbdown/5up (Wideband). I am looking for the best way to achieve wireless and wired performance for our setup. Our gaming computers may be in our bedroom, and we also may bring it down to the office every now and then for “LAN” sessions. Most wireless will be happening downstairs with our laptops, but since we may do LAN sessions then hard wired latency may be important there too. My concerns: If we do only wireless there would be too much latency for gaming. I don’t know if placing one D-link DGL 4500 on the top floor would be enough; which I currently own. (http://dlink.com/us/en/home-solutions/support/product/dgl-4500-xtreme-n-gaming-router) As far as I’m aware wireless signals transfer best top down. Would this wireless router be enough on top floor and that’s it? My second strategy was a combination of wiring and wireless but I’m not sure what’s easiest way to do this? This is a place we’re renting, so I’m not sure how much leeway we have with wiring, but we’re all pretty competent... if we can’t drill through a wall we can probably “stitch” them across the edges wherever needed. Thoughts on the optimal way to do this?

  Read the article

• Computer does not switch on after power outage

  - by cristian

  VOLTAGE DROP OFF FOR PC does not restart The other day my pc was turned off due to power outage. Since that time the computer would not turn on again, no sign of life, it seems dead. I did several tests, changed the power outlet and disconnect the wires ... also I have reseated the cards ... but the result is that nothing changes. What can I do? Could there may be damage to the hardware due to the power outage? Note: the voltage drop is not due to a lightning storm and so is not due to damaged components (burnt card etc ...) Original Text: l'altro giorno il pc mi si è spento improvvisamente per calo tensione.... da quel momento non si è piu' riacceso...nessun segnale di vita...sembra proprio morto. Ho fatto diverse prove, cambio presa di alimentazione, scollegare i fili...insomma ho "mischiato le carte"...ma il risultato è che non cambia nulla. Cosa posso fare? cosa puo' essere successo? Possono esserci danni hardware per il calo di tensione? NB: il calo di tensione non e' dovuto ad una saetta e quindi escluderei danni causa temporale (bruciature scheda ecc...) Grazie mille

  Read the article

• Dell PS/2 Keyboard Stops Working Randomly After Power Disturbance

  - by Kenneth Murphy

  I have a Dell PS/2 keyboard connected to a desktop PC running Slackware 12.2 & Windows XP. After a recent, brief power outage/disturbance at my home, the keyboard has begun to quit working at random times. It has stopped at POST, but not by keyboard error -- I have to press the F1 key to continue booting, and at times the keyboard has already stopped working. Other times, the keyboard will work perfectly for a long time (a day or more) before it finally quits. It has stopped at boot, in Windows XP, and in Slackware. The led lights continue to work regardless. I have tried another PS/2 keyboard and it seems to be immune to this problem. The USB mouse always works. Does anyone have any ideas about how this might have happened? If this is related to the power disturbance that killed the power to the running PC, is it feasible that it would have only fried the keyboard itself (which still works sometimes) and not the PS/2 port nor anything else? I have experienced no other problems since the event.

  Read the article

• Some Power Supply Cable Questions?

  - by jasondavis

  I am building a new PC and I haven't done this in a few years. It will have all the latest tech stuff. I got my PSU in the mail and I am looking over the cables (it has a lot) I thought it was a mudular PSU so I could only use the cables I need but instead it is a hybrid (some wires attached and some can be added/removed instead of all of then being removable). 1) So I am curious, I believe all my hard drives and optical drives are powered off of a sata power cable so does that mean I probably do not need any of the 4 pin molex cables? Or are these used for other things? 2) I know the 24-pin cable goes to my motherboard. 3) I have some 6-pin cables that are labeled pci-e which is new to me. I read these are for some grapghic cards and stuff. I have 2 grapghic cards but they do not require a seperate pci-e power wire be hooked to them. So are these pci-e wires just to power pci-express cards? Or for other things as well? 4) I have a 4pin ATX 12v wire, what is this for? 5) 8 pin EPS, what is this for?

  Read the article

• Confusion on networking service start/stop in Ubuntu

  - by Daniel Ball

  I'm preparing to move and took down two of my servers, leaving only one with some essential services running. What I neglected to consider was that one was the DHCP server(which I realized when somebody contacted me saying they couldn't connect. Whups). So because I only have a few hosts on this small network, I opted to just statically configure them for now. One of these is a new Ubuntu 11.04 server, where I have very little experience. I edited /etc/network/interfaces and /etc/hosts to reflect my changes. I ran $sudo /etc/init.d/networking stop *deconfiguring network interfaces ... So yay. Then I try to start, it gives me the mumbo jumbo about using services (why didn't it do that for the stop?) So instead I run ... $sudo service networking start networking stop/waiting Now, to me that says the status of the service is stopped. But when I ping another computer, I get a successful reply. So is it not actually stopped? More importantly, am I doing something wrong? Edit daniel@FOOBAR:~$ sudo service networking status networking stop/waiting daniel@FOOBAR:~$ sudo service networking stop stop: Unknown instance: daniel@FOOBAR:~$ sudo service networking status networking stop/waiting daniel@FOOBAR:~$ sudo service networking start networking stop/waiting daniel@FOOBAR:~$ sudo service networking status networking stop/waiting So you can see why I ran /etc/init.d/networking stop instead. For some reason upstart (that is what "services" is, right?) isn't working with stop. cat /etc/hosts 127.0.0.1 localhost 127.0.1.1 FOOBAR 198.3.9.2 FOOBAR #Added entry July 19 2011 # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface #auto eth0 #iface eth0 inet dhcp # hostname FOOBAR auto eth0 iface eth0 inet static address 198.3.9.2 netmask 255.255.255.0 network 198.3.9.0 broadcast 198.3.9.255 gateway 198.3.9.15 No I didn't save backups, it was just a minor change so I just commented out the old DHCP setting. Edit I set everything back to original settings and set up a DHCP server. "starting" networking does the same thing. I can only assume this is normal, I just don't know WHY. It can't be anything to do with the configuration files, since they've been restored.

  Read the article

• How to get working cups command line tools on Server 14.04

  - by Nick

  It looks like some of the commands like lpr and lprm have broken versions that don't work with cups. These commands worked properly on 10.04. lpr for cups has an -o option, but no lpr is intalled when cups is installed, and the lpr installed with apt-get install lpr does not have the -o option and does not appear to be the cups version of lpr. man lpr shows BSD General Commands Manual at the top, where man lpr on the Ubuntu 10.04 server said Apple, inc in the same spot. which leads me to believe the "wrong" lpr is in the "lpr" package or package names got moved around. There is also a lprng package, but trying to install it wants to remove cups and cups-client. lprm also returns lprm: PrinterName: unknown printer when PrinterName is in fact a valid printer installed with cups and does appear in lpstat -t. How do I get the proper cups versions of lpr working on Server 14.04?

  Read the article

• Command line options style - POSIX or what?

  - by maaartinus

  Somewhere I saw a rant against java/javac allegedly using a mix of Windows and Unix style like java -classpath ... -ea ... Something IMHO, it is no mix, it's just like find works as well, isn't it? AFAIK, according to POSIX, the syntax should be like java --classpath ... --ea ... Something and -abcdef would mean specifying 6 short options at once. I wonder which version leads in general to less typing and less errors. I'm writing a small utility in Java and in no case I'm going to use Windows style /a /b since I'm interested primarily in Unix. What style should I choose?

  Read the article

• How do I start "Ubuntu classic desktop" (no effects) from the command line

  - by Andrew Stern

  I am able to run sessions over an ssh connection but I rather use the "Ubuntu classic desktop (no effects)" version on Ubuntu 11.04 instead of the new Unity since I don't have 3d support on the laptop I'm using to display the graphical User Interface. How can I startup the older gnome-session without the 3d effects? I tried gnome-session but it seems to be the option with the 3d effects and I want a more stripped down session over my ssh session.

  Read the article

• Any command line calculator for Ubuntu?

  - by AgentCool

  I am looking for a Calculator which can do calculations in the terminal itself without any other extra prefixes and suffixes. For example: If I typed something like 10000-9000 in the terminal, the answer should come out as 1000. Once again I am saying, I just need a quick calculator in terminal, without any characters added. I know if I switch to Python, it can do that but I don't want it in such a way.

  Read the article

• Where do SATA drives get their power when using a PCI SATA controller on oler PCs?

  - by Sukima

  I've been looking into PCI SATA controller cards online for an older PC and noticed that the ports only have the SATA cable connector and the Power supply does not have the SATA power connectors. I also had a few external eSATA drives which don't power up unless I also plugin the USB cable. Therefore I realize that SATA and eSATA do not carry power and need power else where. When converting older PCs to use a PCI SATA controller how do you provide power to the SATA drives? Anticipating the answer to be some kind of converter cable (which I was unable to search for) then can older power supplies handle added drives? (Assuming a 4 port SATA controller means 4 more drives the power supply has to endure). Or do you have to get a second poer supply and kinda jerry-rig it into an old case?

  Read the article

• PSU aka Power Supply won't turn off and No Power_Good - Safe to keep using?

  - by Tek

  The title is the symptoms of my problem. I mainly chose this title for search engines so people can know why this is happening since I see a lot of uncertainty when it comes to this problem. I do have a question related to the source of the problem though. First of all, Inserting the power to the power supply automatically turns on my computer. Using a power supply tester, the tester automatically turns on without me having to push the button to test the PSU. lol. The PG (Power Good) signal is missing. The strange thing is my computer still turns on (OS boots, etc) considering a missing power good signal. Is it really that unsafe to use the power supply when it's missing the power good signal? All the voltages seem to be in check. Here's a picture: Power Supply Tester Readout And by safe (considering the readout) in the sense that is it likely my components (cpu, mobo, etc) could be damaged?

  Read the article

• Problem with reading file line-by-line

  - by Maulrus

  I'm trying to complete an exercise to write a program that takes the following command line arguments: an input file, an output file, and an unspecified number of words. The program is to read the contents of the input file line by line, find for each word given which lines contain the word, and print the lines with their line number to the output file. Here's my code: #include <iostream> #include <fstream> #include <string> #include <sstream> using namespace std; int main(int argc, char* argv[]) { if (argc < 4) { cerr << "Error #1: not enough arguments provided\n"; return 1; } ifstream in(argv[1]); if (!in.is_open()) { cerr << "Error #2: input file could not be opened\n"; return 2; } ofstream out(argv[2]); if (!out.is_open()) { cerr << "Error #3: output file could not be opened\n"; return 3; } ostringstream oss; for (int i = 3; i < argc; ++i) { int k = 0; string temp; oss << argv[i] << ":\n\n"; while (getline(in, temp)) { ++k; unsigned x = temp.find(argv[i]); if (x != string::npos) oss << "Line #" << k << ": " << temp << endl; } } string copy = oss.str(); out << copy; in.close(); out.close(); return 0; } If I try to run that, I get the predicted output for the first word given, but any words following it aren't found. For example, for the source code above will give the following output: in: Line #1: #include <iostream> Line #2: #include <fstream> Line #3: #include <string> Line #4: #include <sstream> Line #5: using namespace std; Line #7: int main(int argc, char* argv[]) { Line #12: ifstream in(argv[1]); Line #13: if (!in.is_open()) { Line #14: cerr << "Error #2: input file could not be opened\n"; Line #22: ostringstream oss; Line #23: string temp; Line #24: for (int i = 3; i < argc; ++i) { Line #26: int k = 0; Line #28: while (getline(in, temp)) { Line #30: unsigned x = temp.find(argv[i]); Line #31: if (x != string::npos) Line #32: oss << "Line #" << k << ": " << temp << endl; Line #35: string copy = oss.str(); Line #37: in.close(); out: That is, it'll find all the instances of the first word given but not any following. What am I doing wrong here?

  Read the article

< Previous Page | 10 11 12 13 14 15 16 17 18 19 20 21  | Next Page >