Search Results

Search found 8523 results on 341 pages for 'sun storage 7000 scriptin'.

Page 140/341 | < Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >

• Will 5 Terabyte NAS drive be compatible with Windows XP SP3 32 bit?

  - by TrevorBoydSmith

  (NOTE: The operating system (in this case Windows XP SP3 32 bit) we are using is not a choice.) I am trying to setup a short term storage device. First, I found a large 5 Terabyte NAS drive that would IMO fulfill my storage requirements. Second, I also found that Windows XP seems to have a hard drive size limit (see 'Is there a limit to the size of a hard drive for Windows XP pre-SP1?'): XP should handle up to 2 TB per volume after the service packs are applied. You are correct. There was a 137gb limit on the orginal pre service pack windows xp. This was addressed/fixed in SP1. My question is, will my Windows XP SP3 32 bit machine see the 5 Terabyte NAS and be able to read/write properly to the NAS drive?

  Read the article

• Exchange 07 to 07 mailbox migration using local continuous replication

  - by tacos_tacos_tacos

  I have an existing Exchange Server ex0 and a fresh Exchange Server ex1, both 2007SP3. The servers are in different sites so users cannot access mailboxes on ex1 as from my understanding, a standalone CAS is required for this. I am thinking of doing the following: Enable local continous replication of the storage group on ex0 to a mapped drive that points to the corresponding storage group folder on ex1 At some point when the replication is done (small number of users and volume of mail), say on a late night on the weekend, disable CAS on ex0 (or otherwise redirect requests on the server-side from ex0 to ex1) AND change the public DNS name of the CAS so that it points to ex1. Will my plan work? If not, please explain what I can do to fix it.

  Read the article

• How to know the level of a symlink in linux?

  - by ???

  For example, if a symlink a -> b b -> c c -> d say, the symlink level of a is 3. Then, is there any utility to get this info? And, also I want to get the expansion detail of a symlink, which will show me something like: 1. /abc/xyz is expanded to /abc/xy/z (lrwx--x--x root root) 2. /abc/xy/z is expanded to /abc/xy-1.3.2/z (lrwx--x--x root root) 3. /abc/xy-1.3.2/z is expanded to /abc/xy-1.3.2/z-4.6 (lrwx--x--x root root) 4. /abc/xy-1.3.2/z-4.6 is expanded to /storage/121/43/z_4_6 (lrwx--x--x root root) 5. /storage/121/43/z_4_6 is expanded to /media/kitty_3135/43/z_4_6 (lrwx--x--x root root) So I can diagnostic with the symlinks. Any idea?

  Read the article

• Grails: GGTS not running on Amazon AWS EC2 anyone else successful?

  - by Anonymous Human

  Im just curious if anyone has had success trying to run the Groovy Grails tool suite on an Amazon AWS EC2 instance with its display exported into your windows machine. If so, I wanted to know which flavor of linux was used on the EC2. I am not having much success with it on the Amazon Linux but haven't tried their Ubuntu instances yet. I got all the way to getting GGTS installed and getting the display exported but when I launch GGTS I get log errors about libraries missing. This is most likely because I didn't use yum to install it so I am probably missing dependencies but I didn't have a choice its not offered as a yum package. Here are my log file errors when I try to launch GGTS: !SESSION 2014-06-08 03:08:04.873 ----------------------------------------------- eclipse.buildId=3.5.1.201405030657-RELEASE-e43 java.version=1.7.0_55 java.vendor=Oracle Corporation Framework arguments: -product org.springsource.ggts.ide Command-line arguments: -os linux -ws gtk -arch x86_64 -product org.springsourc e.ggts.ide !ENTRY org.eclipse.osgi 4 0 2014-06-08 03:08:12.116 !MESSAGE Application error !STACK 1 java.lang.UnsatisfiedLinkError: Could not load SWT library. Reasons: /home/ec2-user/ggts_sh/ggts-3.5.1.RELEASE/configuration/org.eclipse.osgi /bundles/704/1/.cp/libswt-pi-gtk-4335.so: libgtk-x11-2.0.so.0: cannot open share d object file: No such file or directory no swt-pi-gtk in java.library.path /home/ec2-user/.swt/lib/linux/x86_64/libswt-pi-gtk-4335.so: libgtk-x11-2 .0.so.0: cannot open shared object file: No such file or directory Can't load library: /home/ec2-user/.swt/lib/linux/x86_64/libswt-pi-gtk.s o at org.eclipse.swt.internal.Library.loadLibrary(Library.java:331) at org.eclipse.swt.internal.Library.loadLibrary(Library.java:240) at org.eclipse.swt.internal.gtk.OS.<clinit>(OS.java:45) at org.eclipse.swt.internal.Converter.wcsToMbcs(Converter.java:63) at org.eclipse.swt.internal.Converter.wcsToMbcs(Converter.java:54) at org.eclipse.swt.widgets.Display.<clinit>(Display.java:133) at org.eclipse.ui.internal.Workbench.createDisplay(Workbench.java:679) at org.eclipse.ui.PlatformUI.createDisplay(PlatformUI.java:162) at org.eclipse.ui.internal.ide.application.IDEApplication.createDisplay( IDEApplication.java:154) at org.eclipse.ui.internal.ide.application.IDEApplication.start(IDEAppli cation.java:96) at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandl e.java:196) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runAppli cation(EclipseAppLauncher.java:110) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(Ec lipseAppLauncher.java:79) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.ja va:354) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.ja va:181) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl. java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAcces sorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:606) at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:636) at org.eclipse.equinox.launcher.Main.basicRun(Main.java:591) at org.eclipse.equinox.launcher.Main.run(Main.java:1450) at org.eclipse.equinox.launcher.Main.main(Main.java:1426)

  Read the article

• display text when image on-click/hide text when different image click

  - by Jonah1289

  Hi I have created the following effects on the images seen here http://techavid.com/design/test3.html . You see when you hover and then click on each image, they go from grey to color. When you click on one - the others go grey and the one clicked remains color. That's cool, but now I need the text 1st: Sun for example to display and hide along with its graphic button. The word "Sun," is a link that needs to link out to a URL so it has to be separated from the image effect code. What jquery or javascript code do I need to do this? thanks, jonah p.s. How do i properly post the code I have now. I tried to paste code in "enter code here," but received errors - thnx

  Read the article

• Changing the contents of a file with sed in Solaris 10

  - by ubersol

  Hello, I have a bash script that I want to change all occurrences of jdk1.5.0_14 with jdk1.6.0_20 in a file I have the following piece of code : #!/bin/bash myvar="jdk1.6.0_20" sed "s/jdk1.*/$myvar/g" answer_file.1 > answer_file.2 However I have the following information in answer_file.1 (pasting the relevant part): JDKSelection.directory.JDK_LIST=/usr/jdk/jdk1.5.0_14 (v. 1.5.0_14 by Sun Microsystems Inc.) JDKSelection.directory.HIDDEN_JDK=/usr/jdk/jdk1.5.0_14 The code above changes the occurence of jdk1.5.0_14 to jdk1.6.0_20 but also removes the information contained in paranthesis in the first line. So after the change, I need the answer_file.2 file look like this: JDKSelection.directory.JDK_LIST=/usr/jdk/jdk1.6.0_20 (v. 1.6.0_20 by Sun Microsystems Inc.) JDKSelection.directory.HIDDEN_JDK=/usr/jdk/jdk1.6.0_20 How can I achieve this? Thanks for your answers....

  Read the article

• JSF validateLength question

  - by user337515

  I have a input field with validation to validate the max and min length <h:inputText id="LABEL_ID" styleClass="textboxsmall" value="#{sampleDatatableBean.accessionLabelId}" maxlength="5"> <f:validateLength minimum="4" maximum="5" /> </h:inputText> <br/><h:message id="LABEL_ID_MSG" styleClass="errorMessage" for="LABEL_ID" /> It validates but I get the below message: "Value is less than allowable minimum of {0}" Shouldn't {0} be replaced by value from minimum? Not sure why its not picking up the value. Any ideas? Version info: <!DOCTYPE taglib PUBLIC "-//Sun Microsystems, Inc.//DTD JSP Tag Library 1.2//EN" "http://java.sun.com/dtd/web-jsptaglibrary_1_2.dtd"> <tlib-version>1.0</tlib-version> <jsp-version>1.2</jsp-version>

  Read the article

• Why is my PC boot time slow when USB HDD attached?

  - by John

  I have a USB Hard disk that I am using as a secondary drive just for extra storage. When this is attached and I start my PC the second screen says searching for mass storage dives for about 5 minutes before continuing on. The same happens when I have a USB pen disk attached upon boot. If I attach the device after the PC has loaded then it is very quick however plugging and unplugging is not ideal. Is there away to disable this in the BIOS as I cannot instantly see an option. On boot it informs me I have an American Trends AMIBIOS in the BIOS setup it states the version as v02.58 2006. This is running on a ASUS MV2 Motherboard.

  Read the article

• Network Performance issue

  - by qubemarker

  We have three Ubuntu 10.04 servers. One server is a storage server and the other two servers are configured as clients. The storage server has a good amount of capacity and it is integrated with windows Active directory server for Authentication. I am uploading some video files from both clients to the server and when I am uploading data from any one client alone I get about 26 MB/s data transfer rate. When I upload data from both the clients simultaneously I am only getting about 8 MB/s from each client. I have gigabit ethernet cards in all of the servers and a L2 Managed gigabit switch for connectivity. I don’t know why the data transfer rate is decreasing so much in simultaneous read and write. I have tried all of the TCP stack related settings suggested here. Can any assist with getting better read/write performance out of this setup? Any help is appreciated.

  Read the article

• Why am I getting ClassNotFoundExpection when I have properly imported said class and am looking at it in its directory?

  - by Strider

  This is my Javac compiling statement: javac -cp "C:\java\code\j3D\j3dcore.jar;C:\java\code\j3D\j3dutils.jar;C:\java\code\j3D\vecmath.jar" Simple.java compiles with no problems. The three jar files (j3dcore, j3dutils, and vecmath) are the essential jar's for my program (or at least I am led to believe according to this official tutorial on J3D For the record I ripped this code almost line from line from this pdf file. jar files are correctly located in referenced locations When I run my Simple program, (java Simple) I am greeted with Exception in thread "main" java.lang.NoClassDefFoundError: javax/media/j3d/Cavas3d Caused by: java.lang.ClassNotFoundExpection: javax.media.j3d.Canvas3D Currently I am staring directly at this Canvas3D.class that is located within j3dcore.jar\javax\media\j3d\ wtfisthis.jpg Here is the source code: //First java3D Program import java.applet.Applet; import java.awt.BorderLayout; import java.awt.Frame; import java.awt.event.*; import com.sun.j3d.utils.applet.MainFrame; import com.sun.j3d.utils.universe.*; import com.sun.j3d.utils.geometry.ColorCube; import javax.media.j3d.*; import javax.vecmath.*; import java.awt.GraphicsConfiguration; public class Simple extends Applet { public Simple() { setLayout(new BorderLayout()); GraphicsConfiguration config = SimpleUniverse.getPreferredConfiguration(); Canvas3D canvas3D = new Canvas3D(config); add("Center", canvas3D); BranchGroup scene = createSceneGraph(); scene.compile(); // SimpleUniverse is a Convenience Utility class SimpleUniverse simpleU = new SimpleUniverse(canvas3D); // This moves the ViewPlatform back a bit so the // objects in the scene can be viewed. simpleU.getViewingPlatform().setNominalViewingTransform(); simpleU.addBranchGraph(scene); } // end of HelloJava3Da (constructor) public BranchGroup createSceneGraph() { // Create the root of the branch graph BranchGroup objRoot = new BranchGroup(); // Create a simple shape leaf node, add it to the scene graph. // ColorCube is a Convenience Utility class objRoot.addChild(new ColorCube(0.4)); return objRoot; } public static void main(String args[]){ Simple world = new Simple(); } }` Did I import correctly? Did I incorrectly reference my jar files in my Javac statement? If I clearly see Canvas3D within its correct directory why cant java find it? The first folder in both j3dcore.jar and vecmath.jar is "javax". Is the compiler getting confused? If the compiler is getting confused how do I specify where to find that exact class when referencing it within my source code?

  Read the article

• calling hibernate callback

  - by vrkmurali

  HibernateCallback callback=new HibernateCallback() { @Override public Object doInHibernate(Session session) throws HibernateException, SQLException { Transaction transaction=session.beginTransaction(); Query query2 = session.createSQLQuery( "select user_id,user_name from usermasterdao where user_id not in('select usermaster_id from LoginHistoryDAO where logindate between :fromdate and :todate')"); ((SQLQuery) query2).addEntity(UserMasterDAO.class); //query.setParameter("stockCode", "7277"); query2.setParameter("todate", toDate); query2.setParameter("fromdate", fromDate); List result2 = query2.list(); listofNotUsing=result2; System.out.println(result2.size()+"sizeeee"); transaction.commit(); return result2;}} while executing the command getting error like as follows com.vaadin.event.ListenerMethod$MethodException: Invocation of method notUsingButton in com.iton.ioffice.admin.LoginHistory failed. at com.vaadin.event.ListenerMethod.receiveEvent(ListenerMethod.java:530) at com.vaadin.event.EventRouter.fireEvent(EventRouter.java:164) at com.vaadin.ui.AbstractComponent.fireEvent(AbstractComponent.java:1219) at com.vaadin.ui.Button.fireClick(Button.java:567) at com.vaadin.ui.Button.changeVariables(Button.java:223) at com.vaadin.terminal.gwt.server.AbstractCommunicationManager.changeVariables(AbstractCommunicationManager.java:1460) at com.vaadin.terminal.gwt.server.AbstractCommunicationManager.handleVariableBurst(AbstractCommunicationManager.java:1404) at com.vaadin.terminal.gwt.server.AbstractCommunicationManager.handleVariables(AbstractCommunicationManager.java:1329) at com.vaadin.terminal.gwt.server.AbstractCommunicationManager.doHandleUidlRequest(AbstractCommunicationManager.java:761) at com.vaadin.terminal.gwt.server.CommunicationManager.handleUidlRequest(CommunicationManager.java:318) at com.vaadin.terminal.gwt.server.AbstractApplicationServlet.service(AbstractApplicationServlet.java:501) at javax.servlet.http.HttpServlet.service(HttpServlet.java:717) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:290) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:233) at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:191) at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:127) at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:102) at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:109) at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:293) at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:859) at org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.process(Http11Protocol.java:602) at org.apache.tomcat.util.net.JIoEndpoint$Worker.run(JIoEndpoint.java:489) at java.lang.Thread.run(Thread.java:619) Caused by: org.springframework.orm.hibernate3.HibernateQueryException: could not locate named parameter [todate]; nested exception is org.hibernate.QueryPa rameterException: could not locate named parameter [todate] at org.springframework.orm.hibernate3.SessionFactoryUtils.convertHibernateAccessException(SessionFactoryUtils.java:656) at org.springframework.orm.hibernate3.HibernateAccessor.convertHibernateAccessException(HibernateAccessor.java:412) at org.springframework.orm.hibernate3.HibernateTemplate.doExecute(HibernateTemplate.java:411) at org.springframework.orm.hibernate3.HibernateTemplate.execute(HibernateTemplate.java:339) at com.iton.ioffice.admin.DAO.impl.UserServiceDAOImpl.outOfProcess(UserServiceDAOImpl.java:304) at com.iton.ioffice.admin.LoginHistory.notUsingButton(LoginHistory.java:298) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at com.vaadin.event.ListenerMethod.receiveEvent(ListenerMethod.java:520) ... 23 more Caused by: org.hibernate.QueryParameterException: could not locate named parameter [todate] at org.hibernate.engine.query.ParameterMetadata.getNamedParameterDescriptor(ParameterMetadata.java:99) at org.hibernate.engine.query.ParameterMetadata.getNamedParameterExpectedType(ParameterMetadata.java:105) at org.hibernate.impl.AbstractQueryImpl.determineType(AbstractQueryImpl.java:437) at org.hibernate.impl.AbstractQueryImpl.setParameter(AbstractQueryImpl.java:407) at com.iton.ioffice.admin.DAO.impl.UserServiceDAOImpl$4.doInHibernate(UserServiceDAOImpl.java:285) at org.springframework.orm.hibernate3.HibernateTemplate.doExecute(HibernateTemplate.java:406) ... 31 more please help me

  Read the article

• Can you span a single file share across multiple servers?

  - by Mike C.

  Let's say I have one large file server that has a company-wide share. That file server constantly runs into space issues. Now let's say I have a dozen or so random servers (print servers, web servers, etc) that have a ton of free space. Is there a way to utilize that in the company-wide file share? Like spanning the storage across different servers but making that transparent to the user? I know the likely answer is going to be get more storage for the file server, but I just curious if this is conceptually possible. Thanks!

  Read the article

• Multiple Inheritance Debates II: according to Stroustrup

  - by asksuperuser

  I know very well about the traditional arguments about why Interface Inheritance is prefered to multiple inheritance, there has been already a post here : http://stackoverflow.com/questions/191691/should-c-include-multiple-inheritance But according to Stroustrup the real reason why Microsoft and Sun decided to get rid off multiple inheritance is that they have vested interest to do so: instead of putting features in the languages, they put in frameworks so that people then become tied to their platform instead of people having the same capability at a language standard level. What do you think ? Why Sun and Microsoft consider developers too immature to just make the choice themselves ?

  Read the article

• Vmware peaks NFS load every 30 seconds

  - by gtirloni

  We were troubleshooting a performance problem on one of our storage servers and after investigating almost everything in sight we saw that every 30 seconds, Vmware would go from 10k IOPS (NFS) to 30k, 50k, 100k or whatever the server would handle. Most of it were reads. What could cause this raise in NFS operations per second every 30 seconds? The virtual machines are managed by external customers and there isn't much in common between them. While breaking utilization down by filename, we discovered 5-10 virtual machines that contributed more to those peaks but it still doesn't explain why every 30 seconds. There are no other peaks outside that 30 sec period (ie. it stays in an almost constant average). Is there an NFS tweak in Vmware to change that 30 second period? If that's really necessary, we would like to introduce some variation so all that workload isn't dropped all at once. It's causing NFS timeout on the ESX 3.5/4.0 hosts when the storage gets overloaded.

  Read the article

• Find objects between two dates MongoDB

  - by Tom

  I've been playing around storing tweets inside mongodb, each object looks like this: { "_id" : ObjectId("4c02c58de500fe1be1000005"), "contributors" : null, "text" : "Hello world", "user" : { "following" : null, "followers_count" : 5, "utc_offset" : null, "location" : "", "profile_text_color" : "000000", "friends_count" : 11, "profile_link_color" : "0000ff", "verified" : false, "protected" : false, "url" : null, "contributors_enabled" : false, "created_at" : "Sun May 30 18:47:06 +0000 2010", "geo_enabled" : false, "profile_sidebar_border_color" : "87bc44", "statuses_count" : 13, "favourites_count" : 0, "description" : "", "notifications" : null, "profile_background_tile" : false, "lang" : "en", "id" : 149978111, "time_zone" : null, "profile_sidebar_fill_color" : "e0ff92" }, "geo" : null, "coordinates" : null, "in_reply_to_user_id" : 149183152, "place" : null, "created_at" : "Sun May 30 20:07:35 +0000 2010", "source" : "web", "in_reply_to_status_id" : { "floatApprox" : 15061797850 }, "truncated" : false, "favorited" : false, "id" : { "floatApprox" : 15061838001 } How would I write a query which checks the *created_at* and finds all objects between 18:47 and 19:00? Do I need to update my documents so the dates are stored in a specific format? Thanks

  Read the article

• Windows 7 immediately disconnects a USB drive

  - by Daniel Saner

  I am having a problem with Windows 7 x64 consistently disconnecting one specific USB mass storage drive immediately after it is connected. The drive in question is a Cowon C2 digital music player which works in standard mass storage controller mode (i.e. no device-specific drivers needed/available). When I connect the player, Windows plays the "USB connect" sound and the device appears (under its correct name) in the device manager, but it never appears as a drive. The player itself displays "USB Connected" for a split-second before reporting that it has been disconnected again. Since the player, by design, reboots after it has been disconnected, Windows plays the "USB disconnect" sound before restarting the whole cycle once the player has powered back on. I am connecting the player through an Intel X79 Chipset motherboard (Gigabyte GA-X79-UD3) to Windows 7 Pro 64-bit. The player used to work fine the first few times I connected it, showing up as an external drive; it only recently stopped working. It is not a problem with the player, since it works fine when connected to another computer, even such running the exact same operating system. It is also not a problem with the USB controller, since the issue is the same on both the Intel USB 2.0 and the Fresco Logic FL1009 USB 3.0 controller ports. I have also not had the problem with any other drive so far. Among the things I have tried so far: Disabling USB legacy mode in BIOS Disabling energy-saving power down for all USB controllers in Windows' device manager Removing and reinstalling Windows' USB mass storage driver Removing and reinstalling Intel and Fresco Logic USB controller driver Restoring the player to factory defaults None of these made a difference. Again, the player used to work fine on the exact same system just days ago; I didn't install any new hardware or drivers on it since then. I would be very grateful for any hints on what else to try. Edit: Here is another new hint; I found out that when I connect the drive before booting Windows, it is available in Windows Explorer as it should, and does not automatically disconnect. If I remove and reconnect it though, the infinite connect/disconnect-loop starts anew.

  Read the article

• Which is the recommended filesystem for VMware Server / ESXi?

  - by elitalon

  We have a couple of servers in office with VMware Server as virtualization solution. We are planning an upgrade of our infrastructure. Some servers will remain with VMware Server, but we want to migrate some others to VMware ESXi. In both cases we are making a fresh install, and I wonder if there any suggestion/guidelines regarding the host filesystem and its partitions. EDIT: We are using local storage instead of SAN/NAS external storage, because we are not sure if it is worth it to use them given our office size/requirements.

  Read the article

• Windows Server 2003 R2 SIS Groveler start error

  - by 2040techman

  Hi I have a Windows Server 2003 R2 SP2 running and I need to have a WDS with mixed mode so I can deploy Windows 7 & Windows XP images. I went to setup the first image and after the wizard was done copying the correct files I got: Single Instance Storage Groveler: Service did not start (or something like that). I checked event viewer and got this: Event Type: Error Event Source: Service Control Manager Event Category: None Event ID: 7023 Date: 3/26/2012 Time: 7:03:21 PM User: N/A Computer: SERVER2 Description: The Single Instance Storage Groveler service terminated with the following error: The service has not been started. This server is needed very soon because we just got a shipment of several Windows XP capable laptops and need to deploy Windows XP over PXE and this is keeping us from proceeding. Any help is great!!!

  Read the article

• Delete duplicate rows, do not preserve one row

  - by Radley

  I need a query that goes through each entry in a database, checks if a single value is duplicated elsewhere in the database, and if it is - deletes both entries (or all, if more than two). Problem is the entries are URLs, up to 255 characters, with no way of identifying the row. Some existing answers on Stackoverflow do not work for me due to performance limitations, or they use uniqueid which obviously won't work when dealing with a string. Long Version: I have two databases containing URLs (and only URLs). One database has around 3,000 urls and the other around 1,000. However, a large majority of the 1,000 urls were taken from the 3,000 url database. I need to merge the 1,000 into the 3,000 as new entries only. For this, I made a third database with combined URLs from both tables, about 4,000 entries. I need to find all duplicate entries in this database and delete them (Both of them, without leaving either). I have followed the query of a few examples on this site, but whenever I try to delete both entries it ends up deleting all the entries, or giving sql errors. Alternatively: I have two databases, each containing the separate database. I need to check each row from one database against the other to find any that aren't duplicates, and then add those to a third database. Edit: I've got my own PHP solution which is pretty hacky, but works. I cannot answer my own question for 8 hours because I'm new, so here it is for now: I went with a PHP script to accomplish this, as I'm more familiar with PHP than MySQL. This generates a simple list of urls that only exist in the target database, but not both. If you have more than 7,000 entries to parse this may take awhile, and you will need to copy/paste the results into a text file or expand the script to store them back into a database. I'm just doing it manually to save time. Note: Uses MeekroDB <pre> <?php require('meekrodb.2.1.class.php'); DB::$user = 'root'; DB::$password = ''; DB::$dbName = 'testdb'; $all = DB::query('SELECT * FROM old_urls LIMIT 7000'); foreach($all as $row) { $test = DB::query('SELECT url FROM new_urls WHERE url=%s', $row['url']); if (!is_array($test)) { echo $row['url'] . "\n"; }else{ if (count($test) == 0) { echo $row['url'] . "\n"; } } } ?> </pre>

  Read the article

• RAID strategy - 8 1TB drives

  - by alex

  I'm setting up a backup storage device- This machine has Windows Server 2008, on a separate boot drive. It has 8x 1TB drives, and uses a hardware RAID card. My question is, which RAID configuration should I go for? Initially, I was going to go with RAID 5 across all 8 drives, however members on serverFault have advised against it. I was just wondering why? Some people have suggested 2 lots of RAID 5 configuration on 4 of the drives, then striping them... I want to maximise the storage space, as this is a backup unit - will store SQL backups, Acronis Images, files, etc... It won't be for public access, so the I/O won't be that high I wouldn't think.

  Read the article

• How Do I enable Safe Asynchronous Write With NFS?

  - by Joe Swanson

  The NFSv3 documentation talks alot about the concept of "safe asynchronous writes" (last bullet of A1): http://nfs.sourceforge.net/#section_a This is NOT referring to the sync/async option in the server exports file (as the async option in the exports file is NOT safe). As I understand it, safe asynchronous writes is a hybrid between the sync/async exports option. It allows for a server to reply back without flushing to stable storage immediately, but the client will not remove the write request from cache until it has received confirmation that it has been committed to stable storage (and also detects if the server looses power/reboots). I believe that this option is set on the client side, but I have not come across any documentation that shows how to do this. Any ideas?

  Read the article

• Combine WLAN with LAN

  - by fiatux

  I have D-link DSL 2750U wireless router. My PC and notebook are connected to router by Wi-Fi. They can share files or ping each other. I have a network storage unit plugged into router by an ethernet cable. Any of the computers cannot reach that storage unit or ping it. I guess my router isolates LAN network from WLAN network. Is there a way to combine them and get the router treat all devices connected to router in a single network? Thanks.

  Read the article

• Change Text on Landscape mode with Java Code and not XML (Android)

  - by Chowza

  I wrote my layout entirely in java code because it was just more convenient. (I had a lot of textViews and using for statements were more convenient). However, my TextViews require the day of the week and in portrait mode, I would like to cut the day of the week to a short form. For example, I want "Sunday" to show "Sun" for portrait mode, but "Sunday" for landscape mode. I understand how to do this in XML files, but how do I do it in code? I.e. sample code: LinearLayout parent = new LinearLayout(getApplicationContext()); parent.setLayoutParams(new LayoutParams(LayoutParams.MATCH_PARENT,LayoutParams.MATCH_PARENT)); TextView example = new TextView; example.setLayoutParams(mparams); example.setText("Sunday"); //<--make this "Sun" when in portrait but "Sunday" in landscape parent.addView(example);

  Read the article

• When NOT to use virtualisation? [closed]

  - by Nils

  When virtualisation was new, we tried to virtualized everything. Then came the cases where the virtual machine was very much slower than a physical one. It boils down to the following ruleset (with us) when not to virtualize: Network-io-intesive applications (i.e. with many interrupts/packets) Disk-io-intensive (if not on SAN storage) RAM-intensive (this is the most precious resource) Now this is true for a combination of XEN using local DRBD storage. The same seems to be true for Hyper-V using DAS. I wonder - is it true for all combinations - and what are your limits on these combinations?

  Read the article

• External HDD USB 3.0 failure

  - by Philip

  [ 2560.376113] usb 9-1: new high-speed USB device number 2 using xhci_hcd [ 2560.376186] usb 9-1: Device not responding to set address. [ 2560.580136] usb 9-1: Device not responding to set address. [ 2560.784104] usb 9-1: device not accepting address 2, error -71 [ 2560.840127] hub 9-0:1.0: unable to enumerate USB device on port 1 [ 2561.080182] usb 10-1: new SuperSpeed USB device number 5 using xhci_hcd [ 2566.096163] usb 10-1: device descriptor read/8, error -110 [ 2566.200096] usb 10-1: new SuperSpeed USB device number 5 using xhci_hcd [ 2571.216175] usb 10-1: device descriptor read/8, error -110 [ 2571.376138] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2571.744174] usb 10-1: new SuperSpeed USB device number 7 using xhci_hcd [ 2576.760116] usb 10-1: device descriptor read/8, error -110 [ 2576.864074] usb 10-1: new SuperSpeed USB device number 7 using xhci_hcd [ 2581.880153] usb 10-1: device descriptor read/8, error -110 [ 2582.040123] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2582.224139] hub 9-0:1.0: unable to enumerate USB device on port 1 [ 2582.464177] usb 10-1: new SuperSpeed USB device number 9 using xhci_hcd [ 2587.480122] usb 10-1: device descriptor read/8, error -110 [ 2587.584079] usb 10-1: new SuperSpeed USB device number 9 using xhci_hcd [ 2592.600150] usb 10-1: device descriptor read/8, error -110 [ 2592.760134] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2593.128175] usb 10-1: new SuperSpeed USB device number 11 using xhci_hcd [ 2598.144183] usb 10-1: device descriptor read/8, error -110 [ 2598.248109] usb 10-1: new SuperSpeed USB device number 11 using xhci_hcd [ 2603.264171] usb 10-1: device descriptor read/8, error -110 [ 2603.480157] usb 10-1: new SuperSpeed USB device number 12 using xhci_hcd [ 2608.496162] usb 10-1: device descriptor read/8, error -110 [ 2608.600091] usb 10-1: new SuperSpeed USB device number 12 using xhci_hcd [ 2613.616166] usb 10-1: device descriptor read/8, error -110 [ 2613.832170] usb 10-1: new SuperSpeed USB device number 13 using xhci_hcd [ 2618.848135] usb 10-1: device descriptor read/8, error -110 [ 2618.952079] usb 10-1: new SuperSpeed USB device number 13 using xhci_hcd [ 2623.968155] usb 10-1: device descriptor read/8, error -110 [ 2624.184176] usb 10-1: new SuperSpeed USB device number 14 using xhci_hcd [ 2629.200124] usb 10-1: device descriptor read/8, error -110 [ 2629.304075] usb 10-1: new SuperSpeed USB device number 14 using xhci_hcd [ 2634.320172] usb 10-1: device descriptor read/8, error -110 [ 2634.424135] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2634.776186] usb 10-1: new SuperSpeed USB device number 15 using xhci_hcd [ 2639.792105] usb 10-1: device descriptor read/8, error -110 [ 2639.896090] usb 10-1: new SuperSpeed USB device number 15 using xhci_hcd [ 2644.912172] usb 10-1: device descriptor read/8, error -110 [ 2645.128174] usb 10-1: new SuperSpeed USB device number 16 using xhci_hcd [ 2650.144160] usb 10-1: device descriptor read/8, error -110 [ 2650.248062] usb 10-1: new SuperSpeed USB device number 16 using xhci_hcd [ 2655.264120] usb 10-1: device descriptor read/8, error -110 [ 2655.480182] usb 10-1: new SuperSpeed USB device number 17 using xhci_hcd [ 2660.496121] usb 10-1: device descriptor read/8, error -110 [ 2660.600086] usb 10-1: new SuperSpeed USB device number 17 using xhci_hcd [ 2665.616167] usb 10-1: device descriptor read/8, error -110 [ 2665.832177] usb 10-1: new SuperSpeed USB device number 18 using xhci_hcd [ 2670.848110] usb 10-1: device descriptor read/8, error -110 [ 2670.952066] usb 10-1: new SuperSpeed USB device number 18 using xhci_hcd [ 2675.968081] usb 10-1: device descriptor read/8, error -110 [ 2676.072124] hub 10-0:1.0: unable to enumerate USB device on port 1 [ 2786.104531] xhci_hcd 0000:02:00.0: remove, state 4 [ 2786.104546] usb usb10: USB disconnect, device number 1 [ 2786.104686] xHCI xhci_drop_endpoint called for root hub [ 2786.104692] xHCI xhci_check_bandwidth called for root hub [ 2786.104942] xhci_hcd 0000:02:00.0: USB bus 10 deregistered [ 2786.105054] xhci_hcd 0000:02:00.0: remove, state 4 [ 2786.105065] usb usb9: USB disconnect, device number 1 [ 2786.105176] xHCI xhci_drop_endpoint called for root hub [ 2786.105181] xHCI xhci_check_bandwidth called for root hub [ 2786.109787] xhci_hcd 0000:02:00.0: USB bus 9 deregistered [ 2786.110134] xhci_hcd 0000:02:00.0: PCI INT A disabled [ 2794.268445] pci 0000:02:00.0: [1b73:1000] type 0 class 0x000c03 [ 2794.268483] pci 0000:02:00.0: reg 10: [mem 0x00000000-0x0000ffff] [ 2794.268689] pci 0000:02:00.0: PME# supported from D0 D3hot [ 2794.268700] pci 0000:02:00.0: PME# disabled [ 2794.276383] pci 0000:02:00.0: BAR 0: assigned [mem 0xd7800000-0xd780ffff] [ 2794.276398] pci 0000:02:00.0: BAR 0: set to [mem 0xd7800000-0xd780ffff] (PCI address [0xd7800000-0xd780ffff]) [ 2794.276419] pci 0000:02:00.0: no hotplug settings from platform [ 2794.276658] xhci_hcd 0000:02:00.0: enabling device (0000 -> 0002) [ 2794.276675] xhci_hcd 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 2794.276762] xhci_hcd 0000:02:00.0: setting latency timer to 64 [ 2794.276771] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 2794.276913] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 9 [ 2794.395760] xhci_hcd 0000:02:00.0: irq 16, io mem 0xd7800000 [ 2794.396141] xHCI xhci_add_endpoint called for root hub [ 2794.396144] xHCI xhci_check_bandwidth called for root hub [ 2794.396195] hub 9-0:1.0: USB hub found [ 2794.396203] hub 9-0:1.0: 1 port detected [ 2794.396305] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 2794.396371] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 10 [ 2794.396496] xHCI xhci_add_endpoint called for root hub [ 2794.396499] xHCI xhci_check_bandwidth called for root hub [ 2794.396547] hub 10-0:1.0: USB hub found [ 2794.396553] hub 10-0:1.0: 1 port detected [ 2798.004084] usb 1-3: new high-speed USB device number 8 using ehci_hcd [ 2798.140824] scsi21 : usb-storage 1-3:1.0 [ 2820.176116] usb 1-3: reset high-speed USB device number 8 using ehci_hcd [ 2824.000526] scsi 21:0:0:0: Direct-Access BUFFALO HD-PZU3 0001 PQ: 0 ANSI: 6 [ 2824.002263] sd 21:0:0:0: Attached scsi generic sg2 type 0 [ 2824.003617] sd 21:0:0:0: [sdb] 1953463728 512-byte logical blocks: (1.00 TB/931 GiB) [ 2824.005139] sd 21:0:0:0: [sdb] Write Protect is off [ 2824.005149] sd 21:0:0:0: [sdb] Mode Sense: 1f 00 00 08 [ 2824.009084] sd 21:0:0:0: [sdb] No Caching mode page present [ 2824.009094] sd 21:0:0:0: [sdb] Assuming drive cache: write through [ 2824.011944] sd 21:0:0:0: [sdb] No Caching mode page present [ 2824.011952] sd 21:0:0:0: [sdb] Assuming drive cache: write through [ 2824.049153] sdb: sdb1 [ 2824.051814] sd 21:0:0:0: [sdb] No Caching mode page present [ 2824.051821] sd 21:0:0:0: [sdb] Assuming drive cache: write through [ 2824.051825] sd 21:0:0:0: [sdb] Attached SCSI disk [ 2839.536624] usb 1-3: USB disconnect, device number 8 [ 2844.620178] usb 10-1: new SuperSpeed USB device number 2 using xhci_hcd [ 2844.640281] scsi22 : usb-storage 10-1:1.0 [ 2850.326545] scsi 22:0:0:0: Direct-Access BUFFALO HD-PZU3 0001 PQ: 0 ANSI: 6 [ 2850.327560] sd 22:0:0:0: Attached scsi generic sg2 type 0 [ 2850.329561] sd 22:0:0:0: [sdb] 1953463728 512-byte logical blocks: (1.00 TB/931 GiB) [ 2850.329889] sd 22:0:0:0: [sdb] Write Protect is off [ 2850.329897] sd 22:0:0:0: [sdb] Mode Sense: 1f 00 00 08 [ 2850.330223] sd 22:0:0:0: [sdb] No Caching mode page present [ 2850.330231] sd 22:0:0:0: [sdb] Assuming drive cache: write through [ 2850.331414] sd 22:0:0:0: [sdb] No Caching mode page present [ 2850.331423] sd 22:0:0:0: [sdb] Assuming drive cache: write through [ 2850.384116] usb 10-1: USB disconnect, device number 2 [ 2850.392050] sd 22:0:0:0: [sdb] Unhandled error code [ 2850.392056] sd 22:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 2850.392061] sd 22:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 2850.392074] end_request: I/O error, dev sdb, sector 0 [ 2850.392079] quiet_error: 70 callbacks suppressed [ 2850.392082] Buffer I/O error on device sdb, logical block 0 [ 2850.392194] ldm_validate_partition_table(): Disk read failed. [ 2850.392271] Dev sdb: unable to read RDB block 0 [ 2850.392377] sdb: unable to read partition table [ 2850.392581] sd 22:0:0:0: [sdb] READ CAPACITY failed [ 2850.392584] sd 22:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 2850.392588] sd 22:0:0:0: [sdb] Sense not available. [ 2850.392613] sd 22:0:0:0: [sdb] Asking for cache data failed [ 2850.392617] sd 22:0:0:0: [sdb] Assuming drive cache: write through [ 2850.392621] sd 22:0:0:0: [sdb] Attached SCSI disk [ 2850.732182] usb 10-1: new SuperSpeed USB device number 3 using xhci_hcd [ 2850.752228] scsi23 : usb-storage 10-1:1.0 [ 2851.752709] scsi 23:0:0:0: Direct-Access BUFFALO HD-PZU3 0001 PQ: 0 ANSI: 6 [ 2851.754481] sd 23:0:0:0: Attached scsi generic sg2 type 0 [ 2851.756576] sd 23:0:0:0: [sdb] 1953463728 512-byte logical blocks: (1.00 TB/931 GiB) [ 2851.758426] sd 23:0:0:0: [sdb] Write Protect is off [ 2851.758436] sd 23:0:0:0: [sdb] Mode Sense: 1f 00 00 08 [ 2851.758779] sd 23:0:0:0: [sdb] No Caching mode page present [ 2851.758787] sd 23:0:0:0: [sdb] Assuming drive cache: write through [ 2851.759968] sd 23:0:0:0: [sdb] No Caching mode page present [ 2851.759977] sd 23:0:0:0: [sdb] Assuming drive cache: write through [ 2851.817710] sdb: sdb1 [ 2851.820562] sd 23:0:0:0: [sdb] No Caching mode page present [ 2851.820568] sd 23:0:0:0: [sdb] Assuming drive cache: write through [ 2851.820572] sd 23:0:0:0: [sdb] Attached SCSI disk [ 2852.060352] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.076533] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.076538] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.196329] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.212593] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.212599] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.456290] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.472402] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.472408] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.624304] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.640531] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.640536] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.772296] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.788536] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.788541] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2852.920349] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2852.936536] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2852.936540] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2853.072287] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2853.088565] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2853.088570] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.176339] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.192561] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.192567] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.320349] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.336526] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.336531] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.468344] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.484551] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.484556] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.612349] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.628540] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.628545] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.756350] usb 10-1: reset SuperSpeed USB device number 3 using xhci_hcd [ 2884.772528] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b19060 [ 2884.772533] xhci_hcd 0000:02:00.0: xHCI xhci_drop_endpoint called with disabled ep f6b1908c [ 2884.848116] usb 10-1: USB disconnect, device number 3 [ 2884.851493] scsi 23:0:0:0: [sdb] killing request [ 2884.851501] scsi 23:0:0:0: [sdb] killing request [ 2884.851699] scsi 23:0:0:0: [sdb] Unhandled error code [ 2884.851702] scsi 23:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 2884.851708] scsi 23:0:0:0: [sdb] CDB: Read(10): 28 00 00 5f 2b ee 00 00 3e 00 [ 2884.851721] end_request: I/O error, dev sdb, sector 6237166 [ 2884.851726] Buffer I/O error on device sdb1, logical block 6237102 [ 2884.851730] Buffer I/O error on device sdb1, logical block 6237103 [ 2884.851738] Buffer I/O error on device sdb1, logical block 6237104 [ 2884.851741] Buffer I/O error on device sdb1, logical block 6237105 [ 2884.851744] Buffer I/O error on device sdb1, logical block 6237106 [ 2884.851747] Buffer I/O error on device sdb1, logical block 6237107 [ 2884.851750] Buffer I/O error on device sdb1, logical block 6237108 [ 2884.851753] Buffer I/O error on device sdb1, logical block 6237109 [ 2884.851757] Buffer I/O error on device sdb1, logical block 6237110 [ 2884.851807] scsi 23:0:0:0: [sdb] Unhandled error code [ 2884.851810] scsi 23:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 2884.851813] scsi 23:0:0:0: [sdb] CDB: Read(10): 28 00 00 5f 2c 2c 00 00 3e 00 [ 2884.851824] end_request: I/O error, dev sdb, sector 6237228 [ 2885.168190] usb 10-1: new SuperSpeed USB device number 4 using xhci_hcd [ 2885.188268] scsi24 : usb-storage 10-1:1.0 Please help me with my problem. I got this after running dmesg.

  Read the article

< Previous Page | 136 137 138 139 140 141 142 143 144 145 146 147  | Next Page >