Search Results

Search found 5205 results on 209 pages for 'extra'.

Page 143/209 | < Previous Page | 139 140 141 142 143 144 145 146 147 148 149 150  | Next Page >

  • PC doesn't POST with a certain model of PSU

    - by Core Xii
    I have this PC with an Asus P5N32-E SLI motherboard and an Intel Q6600 CPU. I got a new RX-5300 PSU, but it didn't work. The motherboard power LED is on fine When I switch power on, the PC powers up briefly (0.5-1 sec) then shuts down From there on out when I switch power on, it stays on, all fans and components seem to be receiving power, but the motherboard won't POST. No video output, no PC speaker beeps, nothing If I turn the hard switch on the PSU off and then back on again, go to step 2; The PC turns on and then off immediately again, and on subsequent power-ups it stays on but won't POST I disconnected every component but the motherboard, CPU and PSU. Still nothing. I tried three other models of PSU on this PC, both of higher (600) and lower (<300) wattage than the 530 on the RX-5300 and they all work fine. At this point I was convinced the PSU was faulty so I returned it. When the replacement arrived, it behaved exactly the same. So two different units of RX-5300 both with the same symptoms, neither working with this motherboard + CPU. Yet, three other models of PSU work perfectly fine. The PC store couldn't reproduce my problem with the returned PSU. I tried resetting the CMOS with the jumper. I tried with both the 4 and 4+4 (with and without the extra +4 connected) CPU connectors (curiously the RX-5300 comes equipped with both). Could it be a statistical probability that I get two units of the same model of PSU that are faulty in the exact same manner? Could the RX-5300 model itself be somehow incompatible with this motherboard? I was under the impression that PSUs were pretty much universal so long as you have the wattage. Could the motherboard be broken in some such a way as to work with certain PSUs but not others? What's going on here?

    Read the article

  • Linux on MacBook Air

    - by enduser
    I'm thinking of getting a MacBook Air. The answers to this post will help me make my decision. My questions and my understanding of current solutions are: How difficult is it to install a Linux-based OS (like Fedora or Ubuntu)? I've heard a little about rEFIt, but am not sure what to make of it. Is it completely necessary? Do I still need it if I don't plan to dual boot with Mac OS X? Also a dual-boot isn't necessary, I'd just like to run Fedora/Ubuntu by itself, but I'm curious to know if a dual boot is simple. Does everything 'just work'? In my current laptop I need to add a wireless driver (Broadcom card). I've heard Macs use Broadcom wireless cards. Will this be an issue? How about graphics/touchpad (& multitouch)/sound? I'm aware there are tutorials out there on how to install some older version of some os on your Mac, but my questions are a bit more general: Will it be easy to use (install and configure drivers for) recent Linux distributions with a new MacBook Air? Note: I don't mind extra configuration, but would like to know where it'll be necessary, because if it's too much of a hassle I'll look at other hardware.

    Read the article

  • What are the advantages of registered memory?

    - by odd parity
    I'm browsing for a few low-end servers for a startup and I'm a bit confused about the different memory types. The advantage of ECC is clear - single-bit error correction. When it comes to registered memory it seems more vague, especially in systems that support both registered and unbuffered memory. A Google search mostly finds copies of the Wikipedia article, which states that registered memory chips "...place less electrical load on the memory controller and allow single systems to remain stable with more memory modules than they would have otherwise". However I can't find any quantification of this. What I'm wondering about is: Is registered memory an improvement over unbuffered when it comes to soft error rate, or is it purely about the maximum number of modules supported? If yes, at what point (amount of modules or GB of memory) do these improvements start to become noticeable? For a specific example, the HP ProLiant DL 120 G6 server manual states that maximum supported memory configuration is 16 GB unbuffered (4x4GB) or 12 GB registered (6x2GB). In this case I'd rather have the extra 4GB of memory if the reliability difference is negligible.

    Read the article

  • How to Access User Directory shared by Apache on OS X Mountain Lion?

    - by schluchc
    When trying to access the local user web page on localhost/~username, I get a "403 Forbidden". The system web page in /Library/WebServer/Documents is accessible on localhost/ though, so I assume Apache is working fine. I know that this problem has been discussed several times, also on superuser. I implemented and checked all I could find, but I still couldn't solve the problem and would be glad if someone had a suggestion for this particular case: sudo apachectl -t returns Syntax OK. I have a username.conf file in /etc/apache2/users/: <Directory "/Users/username/Sites/"> Options Indexes MultiViews FollowSymLinks AllowOverride AuthConfig Limit Order allow,deny Allow from all </Directory> as proposed here [SuperUser] and in several other tutorials. The permissions of the username.conf file are -rw-r--r-- root wheel, as they should be. The httpd.conf is unchanged and therefore contains the line Include /private/etc/apache2/extra/httpd-userdir.conf. That file in turn contains UserDir Sites Include /private/etc/apache2/users/*.conf <IfModule bonjour_module> RegisterUserSite customized-users </IfModule> So the httpd*.conf files should be ok. The permissions of /Users/username/Sites is drwxr-xr-x 10 username staff and -rw-r--r--@ 1 username staff for the index.html. In the error log I simply get a [Sun Nov 25 22:14:32 2012] [error] [client 127.0.0.1] (13)Permission denied: access to /~username/ denied. And yes, after each change I did the sudo apachectl restart. Any help no how to solve the problem or how to further analyze it would be highly appreciated!

    Read the article

  • What is the name of the this DOS font? Where and how to add it? Why is there a 1 pixel gap?

    - by JBeurer
    So basically I somehow stepped into this webpage: www.braindamage.vg And the first thing that hit me hard was the lovely DOS fonts, so naturally I wanted to get them into my IDE badly. Opened the html source file and CSS file to find the font name: @font-face { font-family: 'Perfect DOS VGA 437'; src: url('http://www.braindamage.vg/wp-content/themes/braindamage/dosfont.eot'); } @font-face { font-family: 'Perfect DOS VGA 437'; src: url('http://www.braindamage.vg/wp-content/themes/braindamage/dosfont.svg#dos') format("svg"), url('http://www.braindamage.vg/wp-content/themes/braindamage/dosfont.ttf') format ('truetype'); } So I download the font, add it using Control Panel - Fonts. But once I start using it (notepad, MSVS 2008 & MSVS2010) I notice that it looks slightly off: It seems like there's 1 extra pixel between each character. How it should look: What is causing it and how to fix this? Is it the windows XP? (i have disabled font smoothing) Or is there something wrong with the font file?

    Read the article

  • HP DL380 G3 2U For Basic Web Server in 2012

    - by ryandlf
    I have an opportunity to pick up a used HP DL380 G3 2U for $100. I'm looking for a basic entry level web server that I can host a small - medium size website on and more or less learn the ins and outs of running my own web server before I bite the bullet and spend a couple grand on a server. The specs are: Dual (2) Intel Xeon 2.4GHz 400MHz 512KB Cache 4GB PC2100 ECC Registered Memory 6 x 72GB 10K U320 SCSI Hard Drives Smart Array 5i RAID Controller Redundant Power Supplies DVD/Floppy, Dual Intel GB NIC's, USB Or would I be better off spending a couple hundred bucks on something like: this new HP Seems like the only major difference is SATA and a bit of storage, but I will likely be implementing a separate storage system of some sort anyways. I guess it also wouldn't hurt to mention that I plan on running a linux server distro, so would the hardware be likely to support linux with a system that is 4 generations old? I don't mind spending a couple hundred extra dollars if its a better solution, but as mentioned previously I am simple looking for a server to learn on and probably use for a year or so while I put together a small - medium size website.

    Read the article

  • How do I fully share a Hard Drive on my Local Network?

    - by GingerLee
    I have 4 computers connected to a router (DD-WRT) My main PC is Windows 7 (Home Premium). This machine has 2 Hard Disks: HD1 is used for my OS and the other (HD2) is used to store files. My 3 other machines are 1. Ubuntu Destop that I use to learn about linux, 2. A Mac OSX laptop, and 3. A netbook running windows 7. How do I easily share HD2 with my other machines? I would like all my machines to have full access & permissions to HD2 however I would like to RESTRICT access to only PCs that are connected to my router (either via LAN and WiFi) --- btw, I know this is not very secure due to WiFi vulnerability , however, I currently MAC address restrict WiFi connections my router. Extra Info: I have already tried to use the Windows Folder Sharing feature: i.e. I right click over the icon of HD2, and click on the Sharing Tab, but in sub-window labeled "Network File and Folder Sharing", the "Share" button is grayed out. I can click on "Advanced Shared" but that just takes me to a screen in which I have to set certain permissions. What is not clear to me is: How do I set a criteria that shares HD2 with all computer connected to my router?

    Read the article

  • How expensive is a hostname in htaccess? Other solutions possible?

    - by Nanne
    For easy allow or disallowing of dynamic IP-adresses you can add them as a hostname in a .htaccess file. As I have read from: .htaccess allow from hostname? it does a reverse lookup on the connecting ip address, seeing if the response matches the allowed name. (Well, actually Apache is doing a double lookup, first a reverse lookup and then a forward lookup on the result of the reverse.) This is the reason we are currently not using dynamic-ip hostnames in the .htaccess: this "sounds" quite heavy: 2 extra lookups for every request. Is this indeed quite heavy, and would a reasonably busy server that is rather looking for less then more load get away with this :)? (e.g.: how does this 'load' compare to the rest? If a request is 1000 times more expensive then the lookups it might be negligible. otoh, it could be that final straw :) ) Are there other solutions? I can write a script that does a lookup of the hostname and put it in .htaccess files ofcourse, but this feels a bit like a hack.

    Read the article

  • Is there a way to use VirtualBox without using it's resource registry?

    - by Catskul
    Summary VirtualBox seems to want everything to be "registered" which makes it much more annoying to work with on the command line. I'm attempting to create an automated script which will create, move, start, stop, and destroy virtual machines and virtual disks. Requiring registration will complicate the task for the following reasons. leaves state information around that can cause unpredicted edgecases causing scripts to fail. creates potential name space collisions for multiple process creating VMs with the same name moving/copying resources on the same machine is more complicated because references in the registry need to be updated copying resources (disk + vm combination) to another machine require reconfiguration once they reach their target machine, and require the transfer of extra meta data to do the reconfiguration. If something unexpectedly fails, and an unregister thus fails to happen, left over configuration information can cause problems in subsequent runs. Use Case My specific use case is for a continuous integration server which creates and destroys VMs and Disk images potentially with the same name, and would require more logic to deal with the registry's statefulness. Imaginary Example It seems that I should just be able to for example (using some imaginary and/or incorrect commands): mkdir foobar customdiskimg_script ./foo/foo.vdi vboxmanage createvm --name "foo" --ostype Linux --basefolder ./foo/foo.xml vboxmanage storagectl ./foo/foo.xml --name foo --add ide vboxmanage storageattach --storagectl foo --medium ./foo/foo.vdi ./foo/foo.xml vboxmanage startvm ./foo/foo.xml TLDR Is there a way to use virtualbox without "registering" harddisks and VMs?

    Read the article

  • Robocopy (without /l flag) running for hours making log file huge, but not actually copying anything

    - by Mickster
    Here's my command: Robocopy C: C:\C_root /FP /BYTES /TEE /S /E /COPYALL /DCOPY:T /MOVE /Z /ETA /XJ /R:2 /W:30 /XF pagefile.sys /XD /LOG:C:\robocopy.log. BTW, notice the /XD option above. After that I had a few directories that I want to omit. I showed these between angle brackets like this: (left angle bracket) a few dirs I wanted to exclude (right angle bracket). Amongst these dirs was the C_root dir itself, so that it did not get into an "infinite" recursion. (This part was stripped from the post because angle brackets apparently have a meta-meaning to superuser.com about hyperlinks.) The command window this was running in listed a few "EXTRA" files then "hung". By this, I mean no more output, no cmnd prompt, and if I tried to scroll it up, it would immediately scroll right back to the bottom. After about six hours, it finally finished, although I never got a cmnd prompt back in the window I started it in. DIR shows the log file at more than 1.3GB, but when I try to do a MORE on it, I get "Cannot access file". C:\C_root never grew larger. Does anyone have an idea what is going on here?

    Read the article

  • nginx reverse proxy slows down my throughput by half

    - by Isaac A Mosquera
    I'm currently using nginx to proxy back to gunicorn with 8 workers. I'm using an amazon extra large instance with 4 virtual cores. When I connect to gunicorn directly I get about 10K requests/sec. When I serve a static file from nginx I get about 25 requests/sec. But when I place gunicorn behind nginx on the same physical server I get about 5K requests/sec. I understand there will be some latency from nginx, but I think there might be a problem since it's a 50% drops. Anybody heard of something similar? any help would be great! Here is the relevant nginx conf: worker_processes 4; worker_rlimit_nofile 30000; events { worker_connections 5120; } http { sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; } sites-enabled/default: upstream backend { server 127.0.0.1:8000; } server { server_name api.domain.com ; location / { proxy_pass http://backend; proxy_buffering off; } }

    Read the article

  • Have some questions about setting up a VPN to my private cloud servers

    - by Pure.Krome
    I've got a number of Virtual Servers running at a pretty big Cloud provider. They are all running Windows 2008 R2. I have a CISCO ASA firewall in front of them. Currently, I've got all ports blocked except 80/443/21/3386 (for Remote Desktop). I asked to have a VPN enabled on the firewall and they said it's easy to do BUT I need to use the 3rd party Cisco software. Now, I don't want to get into a debate about it .. but we don't want to install anything extra on our -client- computers. We all use Windows 7 and we love using the built in VPN client to connect to other private LANS we have setup in other locations. So i'm wondering what options I have to create a VPN tunnel to our private cloud LAN? All our cloud servers are part of WORKGROUP, so there's no Active Directory .. nor do we want to install all that. Secondly, we know we can open up a firewall port - so any ports for starting a VPN is fine! Lastly, I was thinking of just using one of the existing servers as the VPN server (and using the Windows VPN software) .. but I'm not sure this is a good thing? Remember - we just want to use the baked in VPN software in Windows 7 .. which is PPTP or SSTP or L2TP/IPSEC. I would -LOVE- to use some free OSS software. For usernames/passwords? We'd probably just have one account .. like U:Hithere P:whatever.. so we don't need any hardcore account management, like Active Directory, etc. So does anyone have any ideas?

    Read the article

  • Windows 7 black screen after boot animation

    - by t_virus
    This is happening with my windows 7 64-bit install frequently. Today i was trying to install an icon pack. There was already a restore point prior to it so i didn't feel like create one. I replaced the following system files in both system32 and sysWOW64 imageres.dll imagesp1.dll zipfldr.dll and shell32.dll After a reboot i see windows boot animation and then a black screen (with no mouse) I let it like that for 10 minutes and the laptop automatically went to sleep mode. I wake it up and see an error box this error "interactive logon failed to initialize" I close it and i'm left with a black screen again, this time with a mouse though. I tried using automatic system repair. It just tells me to remove any extra hardware (i have none attached atm) System restore finishes successfully but doesn't fix the problem. Safe mode doesn't work either. same black screen after boot animation Can someone help me with this? Also, I'll be grateful anyone can upload those default files (listed above) for both system32 and sysWOW64 from a windows 7 64bit install (no service pack)

    Read the article

  • disable mystery programs running at startup

    - by pstanton
    Hi and sorry for the ambiguous title... I have a few programs that should run at startup which are 'properly' configured to do so via adding shortcuts to the startup directory: C:\Users\[me]\AppData\Roaming\Microsoft\Windows\Start Menu\Programs\Startup However I have (at least) 4 programs which are also starting up, which I can't find where they are configured or how to disable them. I have tried to find them in the above folder, as well as in the 'startup' section of 'msconfig'. The programs include: Skype (for which I have disabled 'start when windows starts' in its options) Thunderbird (for which I cannot find any option to run-at-startup) Task manager (as above) and some anonymous call to javaw (can't find any more details but it fails anyway) The other strange thing is that it seems like these (at least skype and thunderbird) are running 'as administrator' ... i have deduced this because I am unable to use the file-drag-and-drop feature in both (which is a known problem when running 'as administrator'). If someone could guide me to where these extra programs are configured to run-at-startup I would be very greatful! ps. my user account has the administrator role. EDIT: preferrably without another 3rd party tool...

    Read the article

  • How to get a list of Dovecot IMAP users

    - by Colt McCormack
    How do you get a list of users for a dovecot email server that connect via IMAP (as opposed to POP)? Our server is setup to authenticate via LDAP/PAM. Is there an easy way to get a list of the users who are accessing their mail via IMAP, rather than POP? I am about to migrate our server to Google Apps and want to migrate all of the mail for my IMAP users only (couple hundred out of several hundred total users). POP mail will be migrated separately from the client end obviously. I would much rather migrate only the IMAP users rather than the whole domain which would include migrating a bunch of POP mail left in the server that has already been read/sorted/deleted in the client's email program. Migrating all of that extra useless leftover POP mail could waste weeks of migration time. I suppose parsing some logs to see who has connected on an IMAP port (995 or 993) would give me a list would work if someone could help me do that. I know I have the raw dovecot logs, but am hoping for a cleaner solution.

    Read the article

  • Best format for hard drive for Windows and Mac?

    - by Neil
    I have a 500 GB USB External Hard Drive. I need four partitions on it, for the following purposes: 160 GB for a bootable backup of my Mac. 160 GB for a bootable backup of my Windows. 11 GB for a bootable Snow Leopard Install Disk Rest as for file storage. Now I need a partition table which will get recognised on both Windows and Mac, without needing extra software on Windows, which will let me keep bootable copies of both OS'es, but let me access the file storage from both OS'es. Currently, I have a GUI Partition Table, with Mac OS Extended (Journaled) Partitions for the two backups, Mac OS Extended for the Install Disk, and NTFS for the file storage. While this gets recognised perfectly on my Mac, thanks to an NTFS for Mac driver from Paragon, when connected to Windows, the drive is detected by the machine (listed in Safely Remove USB), but not recognised in Windows Explorer unless I install MacDrive, which is not feasible for me to install on public Windows Machines I might wanna access my storage area on. Can someone recommend the best combination of formats and software/drivers to get this done seamlessly?

    Read the article

  • Questions for anyone who has used Sun Type 7 keyboards

    - by Irinotecan
    So I noticed that Oracle is still selling Sun Type 7 keyboard and mouse packages. I was thinking of buying one for a Linux box at my house so I had easy access to some of the extra keys such as Compose and Alt-GR. I have some questions though before I do for anyone who has used these -- it's been a very long time since I've used an actual Sun keyboard. They show that both a PC and UNIX layout is available. Unfortunately, I cannot find anywhere a clear picture of both layouts to determine the difference. Can anyone post pictures of the 2 different layouts for me to take a look at? I don't remember what some of the "Solaris shortcut" keys do, like Props, Front, Stop, and Again. Are these vestiges from OpenWindows? Do they have any usage on a modern Solaris like OpenSolaris running Gnome? Do they automatically map to anything useful on Linux, or am I going to have to map them myself to something with XModMap? When I last used a Sun keyboard, I remember it having a rather mushy feel to it, so I am wondering if any touch typists could weigh in on whether this keyboard "feels nice" for day to day touch typing. Thanks!

    Read the article

  • Minecraft server hosting hardware specifications [on hold]

    - by Andrew Wright
    I am planning on purchasing a server to rent off Minecraft game servers, largely to friends. I am planning on purchasing a 128GB RAM server to save on colocation costs (as I am likely to need more than 32GB and would have to rent 2U of space...) I am hoping for some advice about the processing power needed to deal with this level of RAM. The servers will be run in a shared environment on linux in a VM to make backups easier. The server I have in mind is dual CPU. I have been considering at the low end dual Xeon E5-2609V2 Quad-Core 2.5Ghz, and at the high end dual Xeon E5-2650V2 Eight-Core 2.6Ghz. The difference between these is 6.4 GT/s and 8 GT/s and £3000 for the lower spec server, £4300 for the higher spec. I was hoping I could get advice about whether it is worth paying for the extra/higher speed processor or if I would be wasting my money? Thank you for any help - I appreciate that this is not directly related to professional system administration.

    Read the article

  • Google Apps routing to different servers, depending on domain

    - by Philip
    We are investigating Google Apps for Education for our group of schools. Currently, each school uses their own Exchange (2003) server. Each school has its own domain which I have added to Google Apps as additional domains. I would like to start transitioning certain staff and some new pupils over to Google Apps to start testing. In this interim phase, I need mail to be routed through Google Apps and then, if no appropriate mail box is found, route on to the individual schools depending on the recipient. I do know that it is possible to route mail that does not have an appropriate Google Apps mail account to a single server - under "Settings / E-mail Settings / General Settings / Routing / E-mail routing". This works well for a single organisation where all the extra mail is destined for one place. I do know that it is possible to set up Routes, under "Settings / E-mail Settings / Hosts" and then use rules, found under "Settigns / E-mail Settings / General Settings / Routing / Receiving Routing". I can then filter based on e-mail domain and forward on to the necessary server. My problem with this, as I understand it, is that it ignores the users that have Google Apps accounts set up and sends all mail to the Exchange server. Are there any solutions for this predicament? Many thanks!

    Read the article

  • Proper Rules For SSL Redirect For Subdomains

    - by Zac Cleaves
    RewriteCond %{HTTP_HOST} ^(.*\.)*subexample.example.com$ [NC] RewriteCond %{SERVER_PORT} !^443$ RewriteRule ^(.*)$ https://subexample.example.com/$1 [R] Is what I have been using. It works as long as I go to a specific page, like subexample.example.com/orders.php. But if you try to go to the root of the subdomain, it adds the extra "/example" at the end. Any suggestion on a set of rules that will work? Thank you so much for your responces! Actually, this is what I am trying to do: http://support.mydomain.net >> https://support.mydomain.net AND(!) http://support.mydomain.net/anypage* >> https://support.mydomain.net/anypage* > RewriteCond %{HTTPS} off RewriteRule (.*) > https://%{HTTP_HOST}%{REQUEST_URI} Works, except I need it to only do it for the support.mydomain.net With the above set up, you get a certificate warning if you try to go just mydomain.net, which I do not have or need an SSL certificate installed on. UPDATE! The other issue with the rule I have written above, is that if you try to go to the root of the subdomain (i.e. support.mydomain.net) it goes to https://support.mydomain.net/support This is driving me crazy, help! =) Any help would be greatly appreciated!

    Read the article

  • Why can't I connect to my home SSH (SFTP) server? What am I doing wrong?

    - by Rolo
    I am new to this topic of creating a SFTP server on one's computer. I would like to be able to access the folder on my Windows XP computer via SFTP from another computer or a phone. The following is what I have done so far: I have installed SSH Windows and everything is setup correctly because I can access it (the folder on my pc) via WinSCP. I however cannot access it from my phone. It doesn't connect. The phone can be on the same wireless network as the Windows XP computer, but I would prefer to be able to access this when not in the same network. Now, from what I have read and understood, the following is the information needed to connect: 1) Host Name: This would be my computer's ip address which I access by typing ipconfig in a cmd prompt (I access this easily on my computer because I simply put in localhost or 127.0.0.1) 2) Port Number: That would be port 22 (I have also added this to my router in the port forwarding section). 3) Username: This would be my Windows XP username. This however is my full name, including my middle initial followed by a period. I am wondering if this is maybe causing problems in accessing it from my phone, since the name has spaces and punctuation (the period). 4) Password: The password of my Windows XP computer Extra Info: When I say phone, I mean an Android phone and I am using an ftp / sftp app to access my pc via the phone's cellular network (I also tried the wireless, but that didn't work as well). I have tried more than one program. On one program it tells me Connection timed out and on another it tells me "timeout:socket is not established" Also, I know that I can use the site noip, but I prefer to connect this way first. Also, because I am new to this, I would like to look into what exactly noip is doing and if they would be seeing my files as they are transferred from phone to pc. Thanking you in advance for your help.

    Read the article

  • Which scripting language to use to asynchronously ssh into equipment, run several commands, parse the output, and save to a file on my computer?

    - by Fujin
    There are several points I'd like to stress in my question. I'd like to login by asynchronously ssh'ing into our infrastructure equipment. Meaning, I do not want to connect to only one device, do all the tasks I need, disconnect, then connect to the next device. I want to connect to several devices at once in order to make the process as fast as possible. By equipment I mean 'infrastructure equipment' and not servers. I say this because I will not have the luxury of saving files to the device then transferring them to myself with scp or another method. The output of the scripts that are run will have to be saved directly to my computer. The output of the commands that are run will need to be cleaned up and parsed. Also I want the outputs of each device to be combined into one nice and neat file, not a separate file for each device. This will all be done from a linux box, using ssh, into devices that all use linux'ish proprietary OSes. My guess is the answer to my question will either be a Bash, Perl, or Python script but I figured it wouldn't hurt to ask and to hear the reasons why one way is better than another. Thanks everyone. EXTRA CREDIT: With you answer, include links to resources that will help create the script I described in the language that you suggested.

    Read the article

  • External HDD connecting via USB disconnects wireless LAN connection

    - by Kensai
    Strange problem. I have this MEDION Akoya PC that has a dedicated bay to slide an external HDD sold separately. It's very handy indeed cause the slot is providing a fast USB 3 connection and power to the HDD unit, without extra cables. All works fine except this show-stopper behavior to disconnect me from the router once I slide in the unit and it powers up. The moment I connect the unit the (normally) three-four WiFi connections I see in my neighborhood disappear and my own to the router loses its signal strength (no Internet traffic is possible). After a while it throws me off that one as well, never to connect me again as long as the unit is powered. Once I disconnect the HDD the various signals come back and it automatically reconnects to my own. What takes? Are we in front of a serious design fault by MEDION here? Does the spinning of the HDD on top of the PC cause electromagnetic interference strong enough to throw off my WiFi connectivity? Is it a simple USB problem? Some kind of strange hardware conflict? Where should I look?

    Read the article

  • Will the removal of NAT (with the use of IPv6) be bad for consumers? [closed]

    - by Jonathan.
    Possible Duplicate: How will IPv6 impact everyday users? (World IPv6 Day) As I understand when we have finally made the switch to IPv6 not only will NAT be unnecessary but it is incompatible with IPv6? Will that mean that ISPs will have to serve multiple IP addresses per customer? Will they provide a range of addresses for each customer or as each device connects will they get an IP address that isn't necessarily near that of the other devices in their house? But overall will this be bad for the Internet users? as surely it will allow ISPs to see exactly how many devices are being used, and so allow them to charge for the use of additional IP addresses? And then if that happens, what happens when you try to connect an extra device to your network? Will it simply not get an IP address? In my home we have about 15-20 devices connected at once, but for places where there are hundreds of devices, it seems like the perfect opportunity for ISPs to charge more? I think I may have it completely wrong, so is there somewhere where there is an explanation of who things will work when IPv6 becomes the norm?

    Read the article

  • 1 PC, 2 consoles (as in 2 monitors, keyboards and mice)

    - by ciuly
    I have this desire to "kill 2 birds with one shot". Currently, I have 1 server running round the clock, 1 laptop that runs about 8 hours a day, 7 days a week, and a desktop that runs about the same length of time. All 3 are ... old, to say the least. So there is a great need to upgrade (well, the server might handle its job for another year or so, but that only depends on how much time I have to put it to "work"). Now, I'm "dreaming" of only one PC. I'm thinking vmware's ESX. So there will be a VM for the server, a VM for the "laptop" and one for the "desktop". And obviously I'll have to somehow "link" a set of monitor/keyboard/mouse with one of the laptop/desktop VMs. The server doesn't need such things, obviously (it doesn't have them at this moment either). Is something like this possible? ESX is not a requirement, it's just something I found that answers part of my problems, but there still remains the 2 KVM set that needs connecting and "linking" to appropriate VM. Why I would want to do this? well, first of all, it's much cheaper to upgrade one PC than 3. Then, the power consumption is obviously lower. Plus the extra space.Plus it allows me to better separate networks and services. Thanks.

    Read the article

< Previous Page | 139 140 141 142 143 144 145 146 147 148 149 150  | Next Page >