Search Results

Search found 10674 results on 427 pages for 'glib config'.

Page 143/427 | < Previous Page | 139 140 141 142 143 144 145 146 147 148 149 150  | Next Page >

• CentOS 5.5 remote kickstart installation stalls at "Starting install process." How to debug?

  - by ewwhite

  Hello, I'm having a difficult time with a remote CentOS 5.5 kickstart installation on an HP ProLiant DL360 G6. This is in an environment where I maintain an internal CentOS yum repository. The kickstart installation and post scripts have been tested and normally work. This hardware is also common in this environment, so I do not believe that it is a factor. Unfortunately, I'm having problems with a specific server install. The system is remote to the yum repository at a distance of 500 miles. They are connected over a private low-latency 100-megabit layer 2 connection (26ms round-trip). I'm mounting the 10mb CentOS 5 netinstall ISO image via an HP ILO remote console. The initial boot parameters are: linux ks=http://yum.abctrading.com/prop.cfg ksdevice=eth0 ip=x.x.x.x dns=x.x.x.x netmask=255.255.255.0 gateway=x.x.x.x I'm using the url --url http://ks.abctrading.com/5.5/os/x86_64/ method of installation. This quickly boots into the anaconda installer, pulls the kickstart config and formats the drives. The process eventually halts at the screen below, reading "Starting install process.". Going to the other virtual consoles give the second image below. The process stalls at this point and cannot proceed with the rest of the installation. Running the same kickstart config locally works just fine. I've tried mounting the boot ISO from the console as well as from the ILO2 command line pointing to a locally-hosted boot ISO via http. How can I debug this? Are there any options I've overlooked?

  Read the article

• I Made Wordpress Multisite. And Now Everything Doesn't Display Properly

  - by piratepartypumpkin

  I installed Ubuntu 10.4 then I installed Bitnami LAMP stack then I installed bitnami wordpress module then I tried to make the site into a multisite by following these instructions: http://wiki.bitnami.org/Applications/BitNami_WordPress_Multisite#How_to_add_several_WordPress_Multisite_blogs_with_different_domains.3f AND http://wiki.bitnami.org/Applications/BitNami_WordPress_Multisite I can elaborate if needed: I enabled multisite in my wp-config.php file. Then I created a network using the wordpress dashboard. I was given two blocks of text to copy and paste 1 block into my wp-config.php file and one into my .htaccess file. I did that and now I get this: When I go to my mywebsite.com I get this (this was there before I switched to multisite): If I go to mywebsite.com/wordpress I get this (this used to be a functioning wordpress theme): If I click on "My Blog" it redirects to 1mywebsite.com (where the "1" came from I have no idea) If I try to login by going to mywebsite.com/wordpress/wp-login I get this: and if I enter my user and password it redirects me to mywebsite.com/wp-login.php and gives me "Not Found" The requested URL /wp-login.php was not found on this server. NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /opt/lampstack-5.3.16-0/apps/wordpress ServerName mywebsite.com ServerAlias www.mywebsite.com </VirtualHost>

  Read the article

• How do I import large sql file to local LAMP (xampp) environment

  - by mraslton

  I have used Linux to import a large mysql dump file (into a new database), but am new to how the process works in a local LAMP environment using xampp, as xampp does not support SSH. I've dowloaded the large_dump_file.sql from the Linux server to my local system. I'm using Windows XP and have used xampp to setup LAMP. I am able to access the local_database via phpMyAdmin, but the dump file is too large to import using that app. I'm trying to import the file via the command prompt, but so far with no success. At the prompt: cd .. cd .. cd xampp cd mysql cd bin I've found that mysqlimport is used to import .csv and .txt files, and mysql is used to import .sql files, but can't find documentation as to whether or not to use the -u -p options so I've tried many variations of the command with no luck. What would be the proper command? I've modified the hosts, virtual-hosts conf, and apache config files. Do I need to change any other config files on my local system? Thanks.

  Read the article

• Choose identity from ssh-agent by file name

  - by leoluk

  Problem: I have some 20-30 ssh-agent identities. Most servers refuse authentication with Too many failed authentications, as SSH usually won't let me try 20 different keys to log in. At the moment, I am specifying the identity file for every host manually, using the IdentityFile and the IdentitiesOnly directive, so that SSH will only try one key file, which works. Unfortunately, this stops working as soon as the original keys aren't available anymore. ssh-add -l shows me the correct paths for every key file, and they match with the paths in .ssh/config, but it doesn't work. Apparently, SSH selects the indentity by public key signature and not by file name, which means that the original files have to be available so that SSH can extract the public key. There are two problems with this: it stops working as soon as I unplug the flash drive holding the keys it renders agent forwarding useless as the key files aren't available on the remote host Of course, I could extract the public keys from my identity files and store them on my computer, and on every remote computer I usually log into. This doesn't looks like a desirable solution, though. What I need is a possibility to select an identity from ssh-agent by file name, so that I can easily select the right key using .ssh/config or by passing -i /path/to/original/key, even on a remote host I SSH'd into. It would be even better if I could "nickname" the keys so that I don't even have to specify the full path.

  Read the article

• bond0 and xen = crash

  - by Rajat

  Bonding with xen 1 - Stop all guests. Reboot dom0 after running "chkconfig xend off" and "chkconfig xendomains off". 2 - Configure bond0 by enslaving eth0 and eth1 to it. I added the below two entries to /etc/modprobe.conf. alias bond0 bonding options bond0 mode=6,miimon=100 Content of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none Content of /etc/sysconfig/network-scripts/ifcfg-eth1 DEVICE=eth1 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none Content of /etc/sysconfig/network-scripts/ifcfg-bond0 DEVICE=bond0 IPADDR= NETMASK= ONBOOT=yes BOOTPROTO=static USERCTL=no Did "modprobe bond0" and "service network restart" after that. 3 - Edit /etc/xen/xend-config.sxp Change (network-script network-bridge) To (network-script 'network-bridge netdev=bond0') 4 - Start xend. "service xend start". 5 - chkconfig xend on. 6 - modprode bond0 7 - more /proc/net/bonding/bond0 8 - Create guest images as usual and bridge it to xenbr0. about config i did for my xen kernel rhel 5.3 after i reboot the host server i get in place bond0 get pbond0 and its get disconnect from network only i ping to my vm's on the host server any one have any idea why xen bond0 is acting like that or what is solutions to come out of pbond0 to bond0.

  Read the article

• Apache2.2 not responding on Windows 7 desktop

  - by Adam

  Afternoon! I'm having some trouble with Apache2.2 on Windows 7. For over a year it's been running no problem, but all of a sudden requests have just stopped responding. They don't ever time out, the browser just keeps on waiting for a response, which makes me think it's something blocking communication with Apache. Interestingly though, if I stop Apache the requests fail immediately. The Apache service is running, and using netstat I can see it listening on port 80 as configured: TCP 127.0.0.1:80 0.0.0.0:0 LISTENING If I stop the Apache service, that line disappears. I have an entry within my hosts file for each VHost I'm trying, all pointing to 127.0.0.1. Each VHost is configured to *:80. Nothing however is getting recorded in the access or error (at debug level) log files. I've verified the file paths are correct, even though they were never changed. Neither is anything getting recorded within Windows' Event Log. The problem showed up when I added a new VHost and restarted, however I hadn't been using it for a couple of days prior so I don't believe it's the config change. I have performed a syntax check to be sure, and when starting from the command prompt no errors are reported there. I do have Windows Firewall running, however I've verified the Apache rule is correct and tried turning it off to ensure that wasn't the problem. I've reinstalled Apache, in the hope it might magically fix something using the default config, but still no joy. I've also tried using a different port. I'm completely lost for ideas now. Can anybody help? Cheers Adam

  Read the article

• Apache2 Segmentation fault with wsgi_module

  - by a coder

  Apache 2.2.3 is running as an existing web server under RHEL 5. Attempting to set up Trac using wsgi_module. RHEL 5 ships with python 2.4, so in order to use the current version of Trac (1.0) I needed to install it with easy_install-2.6. Trac works with the default mod_python, however users strongly encourage not using this module as it is officially dead. Using RHEL's package manager, I downloaded/installed python26-mod_wsgi.so. I backed up the httpd.conf, then made the following additions: LoadModule wsgi_module modules/python26-mod_wsgi.so #...# WSGIScriptAlias /trac /www/virtualhosts/trac/deploy/cgi-bin/trac.wsgi <Directory /www/virtualhosts/trac/deploy/cgi-bin> WSGIApplicationGroup %{GLOBAL} Order deny,allow Allow from all </Directory> Next I moved trac.conf to trac.conf.bak (contains mod_python calls). I tested the configuration using: apachectl configtest Syntax is OK. So I reloaded the server config using: service httpd reload At this time, all virtualhosted sites stopped responding. I restored my backup copy of httpd.conf, reloaded the server config, and the virtualhosted sites are being served again. A quick look at the httpd error_log shows: [Mon Oct 08 10:20:04 2012] [info] mod_wsgi (pid=28282): Initializing Python. [Mon Oct 08 10:20:04 2012] [info] mod_wsgi (pid=28280): Attach interpreter ''. [Mon Oct 08 10:20:04 2012] [debug] proxy_util.c(1817): proxy: grabbed scoreboard slot 0 in child 28283 for worker proxy:reverse [Mon Oct 08 10:20:04 2012] [debug] proxy_util.c(1836): proxy: worker proxy:reverse already initialized [Mon Oct 08 10:20:04 2012] [debug] proxy_util.c(1930): proxy: initialized single connection worker 0 in child 28283 for (*) [Mon Oct 08 10:20:04 2012] [info] mod_wsgi (pid=28283): Initializing Python. [Mon Oct 08 10:20:04 2012] [notice] child pid 28249 exit signal Segmentation fault (11) [Mon Oct 08 10:20:04 2012] [notice] child pid 28250 exit signal Segmentation fault (11) [Mon Oct 08 10:20:04 2012] [notice] child pid 28251 exit signal Segmentation fault (11) There are many similar lines, this is just a snip of the log file. Suggestions on what could be going on to cause the Segmentation faults?

  Read the article

• pdo_mysql installation

  - by Arsenal

  Hello, On my server I'm trying to instal PHP Projekt (6). This requires pdo_mysql however. I thought this installation of pdo_mysql would be rather straightforward... I tried using pecl (pecl install pdo_mysql) after installing devel etc, but this came up with a permission denied error. I solved this by using directories that were accessible. It then came up with a cant run C compiled programs however. It also says to check config.log for more details but ironically config.log is automatically removed if the installation process fails... When I try to compile and output a "hello world".c however, it works perfectly. I then tried to download the pdo_mysql stuff and install in myself (using configure and make install). This seemed to do the job, but when I restarted my apache ... no sign of pdo_mysql anywhere even though I adjusted my php.ini file I have read somewhere that you need to recompile PHP with the option pdo_mysql enabled. But how does one do that (I'm using CentOS4). And isn't there any other way than that??? Thanks!

  Read the article

• Install PHP mcrypt on Red Hat 4

  - by Chris

  I'm having a very hard time getting mcrypt for PHP installed on a Red Hat 4 server. I've downloaded the rpm but it tells me: error: Failed dependencies: php-common(x86-32) = 5.4.7-2.fc18 is needed by php-mcrypt-5.4.7-2.fc18.i686 rpmlib(FileDigests) <= 4.6.0-1 is needed by php-mcrypt-5.4.7-2.fc18.i686 libc.so.6(GLIBC_2.4) is needed by php-mcrypt-5.4.7-2.fc18.i686 libltdl.so.7 is needed by php-mcrypt-5.4.7-2.fc18.i686 rtld(GNU_HASH) is needed by php-mcrypt-5.4.7-2.fc18.i686 rpmlib(PayloadIsXz) <= 5.2-1 is needed by php-mcrypt-5.4.7-2.fc18.i686 So when I try to install one of those packages, they also require another 8 packages. So I'm diving into dependency hell here. Now if I try to compile mcrypt from source, this is what I get: checking for libmcrypt - version >= 2.5.0... no *** Could not run libmcrypt test program, checking why... *** The test program failed to compile or link. See the file config.log for the *** exact error that occured. This usually means LIBMCRYPT was incorrectly installed *** or that you have moved LIBMCRYPT since it was installed. In the latter case, you *** may want to edit the libmcrypt-config script: no configure: error: *** libmcrypt was not found But I was able to install libmcrypt from an rpm packages successfully. Any suggestions? Also, I cannot use up2date as it requires an active paid account from Red Hat and since the staff has changed rather rapidly in the last year where I work, no one knows if there even was any support accounts.

  Read the article

• IIS permission configuration issue

  - by Dan

  Sorry the title of this question is a little ambiguous but I don't really have any idea where the issue lies - I'm seeking some clarification of the server error logs. Basically, I had a dedicated server running Windows 2003 and Plesk (v8 I think). Last week the server hardware failed and the entire thing had to be rebuilt from scratch. New hardware was put in, new operating system (Win2008), new Plesk installation (v9.5), new software (MSSQL etc) then all data ported over manually from old C and D drives to restore all 30 client sites. It was hell! All has been okay for a couple of days now but about an hour ago POP! Suddenly all sites went down giving a 500 error. Restarting all services eventually brought everything back online, but I'm now living in total fear. It can - and probably will - happen again. The guys on support gave me the following errors from the server log: The Template Persistent Cache initialization failed for Application Pool 'ASP.NET v4.0 Classic' because of the following error: Could not create a Disk Cache Sub-directory for the Application Pool. The data may have additional error codes.. The worker process for application pool 'domain1.com(domain)(2.0)(pool)' encountered an error 'Cannot read configuration file ' trying to read configuration data from file '\\?\C:\inetpub\temp\apppools\domain1.com(domain)(2.0)(pool).config', line number '0'. The data field contains the error code. The worker process for application pool 'PleskControlPanel' encountered an error 'Cannot read configuration file ' trying to read configuration data from file '\\?\C:\inetpub\temp\apppools\PleskControlPanel.config', line number '0'. The data field contains the error code. The support guys are so ambiguous about this and it scares me horribly. Can anyone positively identify the cause of this error which lead to all client website going offline? What can be done to prevent it from happening again? Any pointers would be very much appreciated! Thanks folks...

  Read the article

• Appears to be "randomly" switching between the acl matched backend and the default backend

  - by Xoor

  I have HAProxy acting as a proxy in front of: An NGinx instance An in-house load balancer in front of multiple dynamic services exposed with socket.io (websockets) My problem is that from time to time my connections are proxied correctly to my socket.io cluster, and then randomly it fallsback to routing to NGinx which obviously is annoying and meaningless since NGinx isn't mean't to handle the request. This happens when requesting for URLs of the format : http://mydomain.com/backends/* There's an ACL in the HAProxy config to match the '/backends/*' path. Here's a simplified version of my HAProxy config (removed extra unrelated entries and changed names): global daemon maxconn 4096 user haproxy group haproxy nbproc 4 defaults mode http timeout server 86400000 timeout connect 5000 log global #this frontend interface receives the incoming http requests frontend http-in mode http #process all requests made on port 80 bind *:80 #set a large timeout for websockets timeout client 86400000 # Default Backend default_backend www_backend # Loadfire (socket cluster) acl is_loadfire_backends path_beg /backends use_backend loadfire_backend if is_loadfire_backends # NGinx backend backend www_backend server www_nginx localhost:12346 maxconn 1024 # Loadfire backend backend loadfire_backend option forwardfor # This sets X-Forwarded-For option httpclose server loadfire localhost:7101 maxconn 2048 It's really quite confusing for me why the behaviour appears to be "random", since being hard to reproduce it's hard to debug. I appreciate any insight on this.

  Read the article

• What does this error mean in my IIS7 Failed Request Tracing report?

  - by Pure.Krome

  Hi folks, when I attempt to goto any page in my web application (i'm migrating the code from an asp.net web site to web application, and now testing it) .. i keep getting some not authenticated error(s) . So, i've turned on FREB and this is what it says... I'm not sure what that means? Secondly, i've also made sure that my site (or at least the default document which has been setup to be default.aspx) has anonymous on and the rest off. Proof: - C:\Windows\System32\inetsrv>appcmd list config "My Web App/default.aspx" -section:anonymousAuthentication <system.webServer> <security> <authentication> <anonymousAuthentication enabled="true" userName="IUSR" /> </authentication> </security> </system.webServer> C:\Windows\System32\inetsrv>appcmd list config "My Web App" -section:anonymousAuthentication <system.webServer> <security> <authentication> <anonymousAuthentication enabled="true" userName="IUSR" /> </authentication> </security> </system.webServer> Can someone please help?

  Read the article

• Getting a "403 access denied" error instead of serving file (using django, gunicorn nginx)

  - by Finglish

  Getting a "403 access denied" error instead of serving file (using django, gunicorn nginx) I am attempting to use nginx to serve private files from django. For X-Access-Redirect settings I followed the following guide http://www.chicagodjango.com/blog/permission-based-file-serving/ Here is my site config file (/etc/nginx/site-available/sitename): server { listen 80; listen 443 default_server ssl; server_name localhost; client_max_body_size 50M; ssl_certificate /home/user/site.crt; ssl_certificate_key /home/user/site.key; access_log /home/user/nginx/access.log; error_log /home/user/nginx/error.log; location / { access_log /home/user/gunicorn/access.log; error_log /home/user/gunicorn/error.log; alias /path_to/app; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Scheme $scheme; proxy_pass http://127.0.0.1:8000; proxy_connect_timeout 100s; proxy_send_timeout 100s; proxy_read_timeout 100s; } location /protected/ { internal; alias /home/user/protected; } } I then tried using the following in my django view to test the download: response = HttpResponse() response['Content-Type'] = "application/zip" response['X-Accel-Redirect'] = '/protected/test.zip' return response but instead of the file download I get: 403 Forbidden nginx/1.1.19 Please note: I have removed all the personal data from the the config file, so if there are any obvious mistakes not related to my error that is probably why. My nginx error log gives me the following: 2012/09/18 13:44:36 [error] 23705#0: *44 directory index of "/home/user/protected/" is forbidden, client: 80.221.147.225, server: localhost, request: "GET /icbdazzled/tmpdir/ HTTP/1.1", host: "www.icb.fi"

  Read the article

• Error while installing boost_1_54

  - by Farhat

  On trying to install boost I get this error during configuration checks. Googling did not give any pointers. [root@heracles boost_1_54_0]# ./b2 install Performing configuration checks - 32-bit : no (cached) - 64-bit : yes (cached) - arm : no (cached) - mips1 : no (cached) - power : no (cached) - sparc : no (cached) - x86 : yes (cached) error: No best alternative for libs/coroutine/build/allocator_sources next alternative: required properties: <link>static <target-os>windows <threading>multi not matched next alternative: required properties: <link>static <segmented-stacks>on <threading>multi not matched next alternative: required properties: <link>static <threading>multi not matched - has_icu builds : no (cached) warning: Graph library does not contain MPI-based parallel components. note: to enable them, add "using mpi ;" to your user-config.jam - zlib : yes (cached) - iconv (libc) : yes (cached) - icu : no (cached) - icu (lib64) : no (cached) - compiler-supports-ssse3 : yes (cached) - compiler-supports-avx2 : no (cached) - gcc visibility : yes (cached) - long double support : yes (cached) warning: skipping optional Message Passing Interface (MPI) library. note: to enable MPI support, add "using mpi ;" to user-config.jam. note: to suppress this message, pass "--without-mpi" to bjam. note: otherwise, you can safely ignore this message. error: No best alternative for libs/coroutine/build/allocator_sources next alternative: required properties: <link>static <target-os>windows <threading>multi not matched next alternative: required properties: <link>static <segmented-stacks>on <threading>multi not matched next alternative: required properties: <link>static <threading>multi not matched - zlib : yes (cached) How can the alternative for allocator sources be located? Thanks.

  Read the article

• Replacing all disks in a non-OS RAID 5 volume

  - by molecule

  Hi all, We currently have a server with 8 x HDD slots. It is a HP DL380G5 with a P400 controller. 2 x HDD are in a RAID 1+0 config and this hosts the OS. 6 x HDD are in a RAID 5 config and holds an Oracle DB. Basically the RAID 5 volume is running out of space and we would like to swap all 6 with higher capacity disks. Excuse my ignorance as I am pretty new to this... I believe we will need to backup the data, delete the RAID volume, insert the new disks, recreate the volume, and restore the data. 2 questions: Do we need to worry about the OS partition or is it completely independent so we can simply take out the 6 and insert 6 new disks and get the controller to recognize the 6 new disks and form a new RAID 5 volume? We should not need to reinstall OS or Oracle correct? Since we are going to restore the data on the volume from another source (our vendor will take care of this) but we would like to keep the existing data on the 6 disks just in case we run into issues and want to fall back, is this possible? Thanks in advance.

  Read the article

• IIS ASP Redirect Removal

  - by Kim L

  We have a website that is setup on IIS 7 and are trying to replace it with a new site, but need a redirect that is in place removed. The old site used a custom file as the homepage (WN-main.asp). We removed all the old site files, including web.config, and placed them in a subdirectory for safe keeping. The new site no longer uses ASP, and we'd like to use a regular index.html as the default. However, when we go to the website, it keeps trying to redirect our .com to .com/WN-main.asp -- and that gives us a 404 Error in the Application for "Default Web Site" because we removed that page. In the IIS "Default Document" settings we have index.html at the top, and WN-main.asp is nowhere to be found in the list (it never was there). We've also removed the web.config file from the root directory, and put the entire old website in a subdirectory. As well as restarted IIS. We're assuming that the redirect is setup somewhere in IIS because if I navigate to .com/index.html which is our new site, it works. Our problem is that oursite.com redirects to oursite.com/WN-main.asp. Grr. If you go to www.worzalla.com you can see how it redirects to the WN-main.asp page right now as the homepage. Any ideas where this redirect could have been setup so we can remove it? Thanks!

  Read the article

• How to configure a shortcut for an SSH connection through a SSH tunnel

  - by Simone Carletti

  My company production servers (FOO, BAR...) are located behind two gateway servers (A, B). In order to connect to server FOO, I have to open a ssh connection with server A or B with my username JOHNDOE, then from A (or B) I can access any production server opening a SSH connection with a standard username (let's call it WEBBY). So, each time I have to do something like: ssh johndoe@a ... ssh webby@foo ... # now I can work on the server As you can imagine, this is a hassle when I need to use scp or if I need to quickly open multiple connections. I have configured a ssh key and also I'm using .ssh/config for some shortcuts. I was wondering if I can create some kind of ssh configuration in order to type ssh foo and let SSH open/forward all the connections for me. Is it possible? Edit womble's answer is exactly what I was looking for but it seems right now I can't use netcat because it's not installed on the gateway server. weppos:~ weppos$ ssh foo -vv OpenSSH_5.1p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /Users/xyz/.ssh/config debug1: Applying options for foo debug1: Reading configuration data /etc/ssh_config debug2: ssh_connect: needpriv 0 debug1: Executing proxy command: exec ssh a nc -w 3 foo 22 debug1: permanently_drop_suid: 501 debug1: identity file /Users/xyz/.ssh/identity type -1 debug2: key_type_from_name: unknown key type '-----BEGIN' debug2: key_type_from_name: unknown key type 'Proc-Type:' debug2: key_type_from_name: unknown key type 'DEK-Info:' debug2: key_type_from_name: unknown key type '-----END' debug1: identity file /Users/xyz/.ssh/id_rsa type 1 debug2: key_type_from_name: unknown key type '-----BEGIN' debug2: key_type_from_name: unknown key type 'Proc-Type:' debug2: key_type_from_name: unknown key type 'DEK-Info:' debug2: key_type_from_name: unknown key type '-----END' debug1: identity file /Users/xyz/.ssh/id_dsa type 2 bash: nc: command not found ssh_exchange_identification: Connection closed by remote host

  Read the article

• Mysql master-master not replicating

  - by frankil

  I'm setting up a master-master mysql replication on two servers (db1 and db2). I started with setting up db2 as a slave to db1 and that works fine. But when I set up db1 as a slave to db2 it isn't replicating. On the face of it everything looks fine but the data isn't replicating. There are no errors in either of the error logs. The slave status is updating the bin log position. I have used mysqlbinlog to examine both the binlog on the db2 and the relay log on db1 and all of the queries are going in there, but not being executed to db1. "show slave status" on both servers shows that both the slave io and sql threads are "Yes" and that the relay log position is updated by the sql thread. Also on both servers: >echo "show processlist" | mysql | grep "system user" 166819 system user NULL Connect 3655 Waiting for master to send event NULL 166820 system user NULL Connect 3507 Has read all relay log; waiting for the slave I/O thread to update it NULL Relevant config for db1: server-id = 1 log-slave-updates replicate-same-server-id = 0 auto_increment_increment = 4 auto_increment_offset = 1 master-host = db2 master-port = 3306 master-user = slaveuser master-password = *** skip-slave-start sync_binlog = 1 binlog-ignore-db=mysql Config for db2 server-id = 2 log-slave-updates replicate-same-server-id = 0 auto_increment_increment = 4 auto_increment_offset = 2 master-host = db1 master-port = 3306 master-user = slaveuser master-password = *** sync_binlog = 1 relay-log=mysql-relay-bin binlog-ignore-db=mysql What else can I look for to make sure db1 executes the queries from db2?

  Read the article

• How to set only specific nginx server block into maintenance mode programmatically

  - by Ville Mattila

  I am looking for a solution to automate one of our application's deployment process. In the beginning of deployment, I would like to programmatically set the specified server into maintenance mode and finally after the deployment has been completed, remove the maintenance mode flag from the nginx server. By maintenance mode, I mean that nginx should response with HTTP Response Code 503 to all the requests (with possible custom page). I know how to set the server block to respond with 503 code (see http://www.cyberciti.biz/faq/custom-nginx-maintenance-page-with-http503/) but the question is about how to do this programmatically and most efficiently. Two options have came to my mind: Option 1: At the beginning of the deployment process, write a maintenance file into document root and conditionally check an existence of the maintenance file in nginx server config: server { if (-f $document_root/in_maintenance_mode) { return 503; } } This method contains certain overhead as the file existence is checked for each request. Is it possible to check the file existence only when loading the nginx config? Option 2: Deployment script replaces the whole nginx server configuration file with a maintenance version and swaps it back in the end of the deployment. If this method is used, I am concerned about possible other automation processes like puppet that may be override the maintenance configuration file.

  Read the article

• Replicated MongoDB server slower than simple shards

  - by displayName

  I tried to compare the performance of a sharded configuration against a sharded and replicated configuration. The sharded configuration consists of 8 shards each running on three different machines thereby constituting a total of 24 shards. All 8 of these shards run in the same partition on each machine. The sharded and replicated version is 8 shards again just like plain sharding, and all 8 mongods run on the same partition in each machine. But apart from this, each of these three machine now run additional 16 threads on another partition which serve as the secondary for the 8 mongods running on other machines. This is the way I prepared a sharded and replicated configuration with data chunks having replication factor of 3. Important point to note is that once the data has been loaded, it is not modified. So after primary and secondaries have synchronized then it doesn't matter which one i read from. To run the queries, I use an entirely different machine (let's call it config) which runs mongos and this machine's only purpose is to receive queries and run them on the cluster. Contrary to my expectations, plain sharding of 8 threads on each machine (total = 3 * 8 = 24) is performing better for queries than the sharded + replicated configuration. I have a script written to perform the query. So in order to time the scripts, I use time ./testScript and see the result. I tried changing the reading preference for replicated cluster by logging to mongo of config and run db.getMongo().setReadPref('secondary') and then exit the shell and run the queries like time ./testScript. The questions are: Where am i going wrong in the replication? Why is it slower than its plain sharding version? Does the db.getMongo().ReadPref('secondary') persist when i leave the shell and try to perform the query? All the four machines are running Linux and i have already increased the ulimit -n to 2048 from initial value of 1024 to allow more connections. The collections are properly distributed and all the mongods have equal number of chunks. Goes without saying that indices in both configurations are the same.

  Read the article

• XP SP2 Event log not logging events

  - by Weedfreer

  I have a problem whereby a terminal appears not to be logging events correctly and occasionally appears to have problems communicating accross the network.The terminal has previously been infected with a virus which apears to have 'played' with the default group policy in the standard user profile. Although, outwardly, the terminal appears to be working normally I still have a nagging feeling that it isn't quite back to the way it was. It was infected by a user plugging in a USB Stick while the company was using the older version of the AV software...typically a week or so before it was updated.I have configured the Event logs to Overwrite as required and to be 5056KB in Maximum size. I have also attempted:- Disabling the Event Log service & restarting Renewing the EVT files in Windows\system32\config directory Restarting the event log service and restarting Clearing the event log in the Services MMC Resetting the Filters to Default in the services MMC Using the EVENTCREATE command remotely from a CMD window on the server to force an event creation event. So far the only operation to have any sort of success is the remote computer EVENTCREATE command from a CMD window on the server. As it stands, the only other time that the computer has managed to create events is while it is being restarted.Has anyone gotany ideas on how to proceed? I'm thinking that possibly a refresh of the 'Windows\system32\config\SystemProfile' folder. I'm also thinking about running a tool such as Malwarebytes but this could be slightly controvertial as the system needs to be running on 'up-time' for as long as possible. I'm also wonderign whether anyone knows of any Windows admin tools that allow me to control the event logging options or default security options so that i could get it back to some sort of standard.What I'm trying to avoid is a complte re-imaging of the terminal. Although this is an option, I dont really want to have to take it if i dont need to.Many thanks in advance for any suggestions anyone may be able to provide.

  Read the article

• DNS requests failing from computers that can ping DNS server

  - by dunxd

  I have a situation where computers in some of our remote offices from time to time lose the ability to use our DNS server (in head office) to resolve hostnames. The offices are connected via VPN using Cisco ASA 5505 (VPNclient config rather than Site to Site). Ping to the IP address of the DNS server works. But nslookup will get a "no response from server" message. Computers in other locations can use DNS fine. This is an intermittent problem. One day/hour it works, another it doesn't. Other offices connected in the same way work when another doesn't. No config changes have been made on routers around the time we see the problem. Some users have reported that the problem goes away after doing a repair connection in Windows XP. I think this could be caused by the DNS cache being flushed as part of this - the Windows DNS cache makes the intermittent problem look less so because it caches failed lookups as well as successful ones. However, it is possible some other aspect of Windows is involved. Windows 7 clients have also had the same problem. Any pointers on deeper troubleshooting, or anyone else found this?

  Read the article

• How can I disable Kerberos authentication for only the root of my site?

  - by petRUShka

  I have Kerberos-based authentication and I want to disable it on only root url: http://mysite.com/. And I want it to continue to work fine on any other page like http://mysite.com/page1. I have such things in my .htaccess: AuthType Kerberos AuthName "Domain login" KrbAuthRealms DOMAIN.COM KrbMethodK5Passwd on Krb5KeyTab /etc/httpd/httpd.keytab require valid-user I want to turn it off only for root URL. As workaround it is possible to turn off using .htaccess in virtual host config. Unfortunately I don't know how to do it. Part of my vhost.conf: <Directory /home/user/www/current/public/> Options -MultiViews +FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> UPD. I'm using Apache/2.2.3 (Linux/SUSE) I tried to use such version of .htaccess: SetEnvIf Request_URI ^/$ rootdir=1 Allow from env=rootdir Satisfy Any AuthType Kerberos AuthName "Domain login" KrbAuthRealms DOMAIN.COM KrbMethodK5Passwd on Krb5KeyTab /etc/httpd/httpd.keytab require valid-user Unfortunately such config turn Kerberos AuthType for all URLs. I tried to place first 3 lines SetEnvIf Request_URI ^/$ rootdir=1 Allow from env=rootdir Satisfy Any after main block, but it didn't help me.

  Read the article

• Mercurial internal Setup on Windows 7 - Exception happened during processing of request from ...

  - by Sad0w1nL1ght

  Hy, i have 1 central repository and many locals. On my machine i have local and a central repository too. I can make clone/commit/update/push/pull very easy between the local and central repository on my local machine. but when i want to make a clone from another machine it gets an error. listening at http://MyLocalMachine:8000/ (bound to *:8000) ---------------------------------------- Exception happened during processing of request from ('192.168.0.194', 49319) Traceback (most recent call last): File "SocketServer.pyc", line 558, in process_request_thread File "SocketServer.pyc", line 320, in finish_request File "mercurial\hgweb\server.pyc", line 47, in __init__ File "SocketServer.pyc", line 615, in __init__ File "BaseHTTPServer.pyc", line 329, in handle File "BaseHTTPServer.pyc", line 323, in handle_one_request File "mercurial\hgweb\server.pyc", line 79, in do_GET File "mercurial\hgweb\server.pyc", line 70, in do_POST File "mercurial\hgweb\server.pyc", line 63, in do_write File "mercurial\hgweb\server.pyc", line 127, in do_hgweb File "mercurial\hgweb\hgweb_mod.pyc", line 86, in __call__ File "mercurial\hgweb\hgweb_mod.pyc", line 118, in run_wsgi ErrorResponse ---------------------------------------- The command line wich started the central repo: hg serve -R TT -n TTZoli The command from remote machine for cloning: hg clone --pull http://MyLocalMachine:8000/TT Config for the central repo: [ui] username = MyLocalUserName username = test <[email protected]> with this user i'm trying to acces the central repo [web] push_ssl = false Config for the remote repo: [ui] username = test <[email protected]> [web] push_ssl = false I'm not sure if it's relevant,my firewall is turned off on both machines, and the files in /hg folder are not versioned on the server, except hgignore. Could you please suggest some ideas? What could be the problem? Thanks in advance!

  Read the article

• Joomla SMTP Configuration Issue

  - by msargenttrue

  I'm having an issue with the SMTP setup of my Joomla website when trying to send mass emails through the CB Mailing (Mass Email) extension. I receive this error: SMTP Error! The following recipients failed: Number of users to whom e-mail was sent: 0 (Total in list: 1) The old version of this websites mass emailer worked fine, however, in order to add Kunena Forum and maintain compatibility I had to make several upgrades to the site. Both the new version and old verson configurations are outlined below. Server for Website: Mac OS X Server 10.4.11, Apache 1.3.4.1, PHP 5.2.3, MySQL 4.1.22 Server for SMTP: Eudora Internet Mail Server 3.3.9 (EIMS Server X) New Configuration: Joomla 1.5.25, Community Builder 1.7.1, CB Paid Subscriptions (CB Subs) 1.2.2, CBMailing 2.3.4, Kunena Forum 1.7.0, Legacy 1.0 plug-in disabled Mail Settings (New Config): Mailer: SMTP Server Mail from: [email protected] From Name: CASPA Sendmail Path: /usr/sbin/sendmail SMTP Authentication: Yes SMTP Security: None SMTP Port: 25 SMTP Username: [email protected] SMTP Password: xxxxxxx SMTP Host: 209.48.40.194 Old Configuration (Working SMTP Configuration): Joomla 1.5.9, Community Builder 1.2, CB Paid Subscriptions (CB Subs) 1.0.3, CB Mailing 2.1, Legacy 1.0 plug-in enabled Mail Settings (Old Config): Mailer: SMTP Server Mail from: [email protected] From Name: CASPA Sendmail Path: /usr/sbin/sendmail SMTP Authentication: Yes SMTP Username: [email protected] SMTP Password: xxxxxxx SMTP Host: 209.48.40.194 (Notice how the older version of Joomla is missing the 2 fields: SMTP Security and SMTP Port) Thanks in advance!

  Read the article

< Previous Page | 139 140 141 142 143 144 145 146 147 148 149 150  | Next Page >