Search Results

Search found 11914 results on 477 pages for 'networking architecture'.

Page 143/477 | < Previous Page | 139 140 141 142 143 144 145 146 147 148 149 150  | Next Page >

• VMWare ESXi virtual machine can contact the gateway but not the DNS server

  - by Nathan Palmer

  I am having a bit of a strange issue. I have a VMWare ESXi server with two virtual machines running on it. They are running just fine and can communicate on the network without a problem. I am now trying to add a third. I am installing Ubuntu 8.04 Server. I assign it a static IP address and it's a fresh installation. Once installed I can ping the gateway but I cannot ping the DNS server. It's on the same network with the other two VMs which are communicating just fine. I have tried to reinstall the operating system but it still fails to connect. Here is /etc/network/interfaces auto eth0 iface eth0 inet static address 192.168.1.23 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 208.67.222.222 #opendns dns-search mydomain.com Here is route Destination | Gateway | Genmask | Flags | Metric | Ref | Use | Iface localnet | * | 255.255.255.0 | U | 0 | 0 | 0 | eth0 default | 192.168.1.1 | 0.0.0.0 | UG | 100 | 0 | 0 | eth0 Since I'm running this behind a FortiGate this is what the sniff command gives me when I try to ping 208.67.222.222 arp who-has 192.168.1.1 tell 192.168.1.23 arp reply 192.168.1.1 is-at MAC 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request 192.168.1.23 -> 208.67.222.222: icmp: echo request As you can see it looks like I never get a response. One interesting thing I notice is the arp reply's MAC doesn't look right. I have cleared the FortiGate's ARP cache though and checked the entry and it seems correct. The MAC it lists is the one for the router. However if I ping from a different virtual machine that is also Ubuntu 8.04 with a nearly identical configuration I get this. 192.168.1.22 -> 208.67.222.222: icmp: echo request 208.67.222.222 -> 192.168.1.22: icmp: echo reply 192.168.1.22 -> 208.67.222.222: icmp: echo request 208.67.222.222 -> 192.168.1.22: icmp: echo reply 192.168.1.22 -> 208.67.222.222: icmp: echo request 208.67.222.222 -> 192.168.1.22: icmp: echo reply So, what could I be missing? Thanks.

  Read the article

• Load balancing with 2 wireless cards

  - by user2544786

  I'm thinking about building a wireless load balancer (if that makes sense). For example, the first wireless card will accept all connections for ip 192.168.1.1 and the second card will serve requests for 192.168.1.2. I know that I can assign both IPs to a single card and all requests will be served by a single wireless card. Would it be better (more bandwidth, more stable connection, etc?) to have two physical cards instead?

  Read the article

• How to connect my Android to my Laptop wirelessly , to stream data between the two?

  - by Deepun

  I want to stream data from my Laptop PC to my Android phone using TCP or UDP by creating sockets in both the phone and the laptop, but it has to be done wirelessly. How do I connect them to stream the data ? I thought creating an ad-hoc wireless network from my laptop and connecting to it using my Android would work. But my Android is not detecting the ad-hoc network. Is there any other way how I can connect the two ? I downloaded this software called 'connectify' and created a wifi hotspot on my laptop, and successfully connected the two. But will I be able to stream data to my device using this connection ? Can simple direct Bluetooth connection help me in creating sockets in both phone and laptop and stream the data ?

  Read the article

• Multiple Homed Windows 2008 Server / Windows 7 Client

  - by Daniel Scott

  I have a small Windows 2008 network, with some Windows 7 clients. The clients are both laptops with docking stations and I would like them to communicate with the Windows 2008 server (for filesharing) through the wired network whilst they're docked. Internet connectivity for all machines (clients and server) is via a Wireless LAN, so the wireless adapter in the Windows 7 clients stays active while they're docked. When the laptops are un-docked, it would be nice to still be able to contact the windows 2008 server for print sharing (and slower file sharing) - hence the server also being on the wireless LAN. The windows 2008 server is running Active Directory, DHCP and DNS. It controls DHCP leases on the wired network and holds the DNS records for "myserver.mycompany.local", which is what the filesharing clients connect to. Ideally I'd like the DNS records to return the wired IP first so that this is the address that the laptops will attempt initially - but there doesn't seem to be a way to do that? At present the server's IP on the wireless LAN comes out of an nslookup above the wired Lan IP. The multi-homing works perfectly - but in the wrong order! Switch on the wireless lan and ping myserver and it goes to the wireless IP. Disable the wireless on the client and do the same ping again and after a couple of seconds it starts pinging the wired address. Does anyone have any suggestions on how to make this work in a predictable order? - or even if it can work. Alternative 1? If it can't work, then would this work: Remove the wireless adapter from the server, put a wireless router/bridge on the wired network (set up to route to/from the wireless LAN's subnet), then configure the clients with two routes to the (now) single IP of the server with metrics favouring direct communication over the wired LAN first? Alternative 2? Should I instead single-home the laptops so all of their connectivity is via the wired-LAN while they're docked? (and route via the windows 2008 server - or a dedicated wireless bridge/router)? My concern here is that I'd like undocking to be seamless - and if the clients are in the middle of downloading something from the internet I wouldn't want whatever they're doing interupted as they switch IP addresses onto the Wireless network. Perhaps this isn't the case and I'm concerned over nothing? Any thoughts? :) UPDATE I seem to have cracked it (at least DNS entries come out in the order I hope for - and pinging the server with various combinations of wired, wireless and both interfaces enabled uses the IP I want) ... I set the binding order of the NICs on the Server (which is acting as Domain Controller, DHCP and DNS server) so that the Wired NIC is before the Wireless adapter. (Start -- type "Network Interfaces" -- Select "View Network Connections" -- Press Alt to show classic dropdown menus -- Advanced -- Advanced Settings) Now, an nslookup (from the client) of the server's hostname returns the Wired IP first, followed by the Wireless IP. The wired IP now seems to be used whenever it's contactable. Incidentally, the metrics on the wired and wireless routes (on the client) also favour the wired LAN (based on Windows' automatically assigned metrics) - but this was always the case, even when I was having trouble getting the wired IP to be "favoured". I'm not entirely sure if this is coincidence - or if a DNS server running on Windows, handing back IP addresses for itself does actually take the binding order of it's own network interfaces into account? It would be interesting to hear from someone who can confirm or deny that (or confirm that the binding order on the server plays a role for some other reason?)

  Read the article

• Mac OS X 10.8 VPN Server: Bypass VPN for LAN traffic (routing LAN traffic to secondary connection)

  - by Dan Robson

  I have somewhat of an odd setup for a VPN server with OS X Mountain Lion. It's essentially being used as a bridge to bypass my company's firewall to our extranet connection - certain things our team needs to do require unfettered access to the outside, and changing IT policies to allow traffic through the main firewall is just not an option. The extranet connection is provided through a Wireless-N router (let's call it Wi-Fi X). My Mac Mini server is configured with the connection to this router as the primary connection, thus unfettered access to the internet via the router. Connections to this device on the immediate subnet are possible through the LAN port, but outside the subnet things are less reliable. I was able to configure the VPN server to provide IP addresses to clients in the 192.168.11.150-192.168.11.200 range using both PPTP and L2TP, and I'm able to connect to the extranet through the VPN using the standard Mac OS X VPN client in System Preferences, however unsurprisingly, a local address (let's call it internal.company.com) returns nothing. I tried to bypass the limitation of the VPN Server by setting up Routes in the VPN settings. Our company uses 13.x.x.x for all internal traffic, instead of 10.x.x.x, so the routing table looked something like this: IP Address ---------- Subnet Mask ---------- Configuration 0.0.0.0 248.0.0.0 Private 8.0.0.0 252.0.0.0 Private 12.0.0.0 255.0.0.0 Private 13.0.0.0 255.0.0.0 Public 14.0.0.0 254.0.0.0 Private 16.0.0.0 240.0.0.0 Private 32.0.0.0 224.0.0.0 Private 64.0.0.0 192.0.0.0 Private 128.0.0.0 128.0.0.0 Private I was under the impression that if nothing was entered here, all traffic was routed through the VPN. With something entered, only traffic specifically marked to go through the VPN would go through the VPN, and all other traffic would be up to the client to access using its own default connection. This is why I had to specifically mark every subnet except 13.x.x.x as Private. My suspicion is that since I can't reach the VPN server from outside the local subnet, it's not making a connection to the main DNS server and thus can't be reached on the larger network. I'm thinking that entering hostnames like internal.company.com aren't kicked back to the client to resolve, because the server has no idea that the IP address falls in the public range, since I suspect (probably should ping test it but don't have access to it right now) that it can't reach the DNS server to find out anything about that hostname. It seems to me that all my options for resolving this all boil down to the same type of solution: Figure out how to reach the DNS with the secondary connection on the server. I'm thinking that if I'm able to do [something] to get my server to recognize that it should also check my local gateway (let's say Server IP == 13.100.100.50 and Gateway IP == 13.100.100.1). From there Gateway IP can tell me to go find DNS Server at 13.1.1.1 and give me information about my internal network. I'm very confused about this path -- really not sure if I'm even making sense. I thought about trying to do this client side, but that doesn't make sense either, since that would add time to each and every client side setup. Plus, it just seems more logical to solve it on the server - I could either get rid of my routing table altogether or keep it - I think the only difference would be that internal traffic would also go through the server - probably an unnecessary burden on it. Any help out there? Or am I in over my head? Forward proxy or transparent proxy is also an option for me, although I have no idea how to set either of those up. (I know, Google is my friend.)

  Read the article

• Cisco QoS Guidence

  - by Kyle Brandt

  I have a 10M connection to the internet that is hooked into a 100M port. I am getting started with QoS, and am hopping for a little guidance on setting it up on a Cisco 3825 router. Right now I am going forward with the idea that I have to implement it on my router, and the provider can't provide QoS for me. How I envision it working is that the QoS will drop or queue packets on my router and that will help prevent a situation where the provider has to start dropping a lot of packets. Right now all I am tasked with is making sure that one of the 3 LANs gets a certain slice (say 3M for Gig Lan1) of the 10M internet connection (But ideally this will be more flexible in the Future). 10M Internet on 100M port on HWIC-4ESW +-----------------------+ | | Gig Lan1 | Cisco 3825 | Lan3 on HWIC-4ESW | | +-----------------------+ Gig Lan2 I need to learn more about QoS, but having a target technology and maybe example configuration will help me wrap my head around the reading I am doing a little more. Which Cisco QoS Technology do you recommend for this particular situation? Have a basic sample config of how this might work? Right now the 10M line is not congested, so this more to have something in place in case it starts to become mildly congested in the future.

  Read the article

• Missing eth0 configuration file

  - by Godric Seer

  I have two servers both running Scientific Linux 6 on the same network. Since I want SSH access to both of them, I want to give them both static IPs so I can setup port forwarding and not worry how my router assigns local IPs. I found that I need to edit the configuration file /etc/network-scripts/ifcng-eth0, however that file does not exist. The network card works fine, and I am able to ssh as long as I access the router and find the local ip. Can I simply make my own configuration file, or did I miss some step in configuring the system that I need to complete?

  Read the article

• Sonicwall 3500 (Creating VLANS for usage of multiple SSID)

  - by Thomas Chia

  I have an issue here. Here is my setup: X0 - STAFF network | X2 - AGENT network | X4 - Wireless AP (for multiple SSID) Okay, basically I'm going to set up the wireless AP to be broadcasting 2 SSID, STAFF-WIFI and AGENT WIFI. When connected to STAFF-WIFI, the users will be connected to the STAFF network, while connected to the AGENT WIFI, the users will be connected to the AGENT network. Can someone explain in details how to go about setting up this configuration? Thanks!

  Read the article

• Cloudstack virtual machines can't communicate with virtual routers when they are on different hosts

  - by Jorge Suárez de Lis

  I'm using Cloudstack 2.2.14 on a Ubuntu 10.04 set of hosts, and I have a problem on my setup. I have two hosts running. When a virtual router is created on host 1 and a virtual machine using that virtual router is created on host 2, or vice versa, I have no connectivity at all on the virtual machine. First of all, I have to setup the network manually on that virtual machine -usually DHCP is working, but not here-. Then, I can't ping to the virtual router from the virtual machine or vice versa. When both virtual router and virtual machine are created on the same host, everything works! Maybe those packages are being filtered somehow? I have no clue on how to proceed. Both hosts can communicate directly outside the virtualization.

  Read the article

• Router and Switch VLAN Configuration for Isolated Network

  - by Ben

  I haven't worked with VLANs much in the past and I was hoping if I could get a good explanation of what I need to setup for this to work. I have a Netgear WNR2000v2 router and a Netgear GS108T smart switch currently in my network. The fourth port on the router connects to port one on the switch. I would like to be able to isolated port 8 on the switch for use as a "guest port" when I bring home malware infested PCs for repair. I figured the VLAN capabilities of the GS108T would be able to do this for me, but I think I have a misunderstanding of how the VLAN actually works. Port 8 needs internet access but should not be able to communicate with the rest of the PCs on the home network. The subnet for the home network is 192.168.1.0/24 and I would like the guest PC to have A) 192.168.1.64 or B) 192.168.2.2. I am reading a lot of stuff about port trunking and VLAN membership, but I am confused as to which setup needs to be in place to make this work. Any help is greatly appreciated! Let me know if there is more information I need to provide. Definitely looking to learn something from this project. Thanks!

  Read the article

• How can I use two Internet connections in Ubuntu?

  - by Martin

  My goal is to be able to do something like this: curl google.com --interface ppp0 curl google.com --interface p2p2 ppp0 is a DSL connection, and p2p2 is a separate direct Internet connection. Currently I can only get one of these to work at a time. When I enable one, the other one stops working. /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # DSL auto p2p1 iface p2p1 inet manual auto dsl-provider iface dsl-provider inet ppp pre-up /sbin/ifconfig p2p1 up # line maintained by pppoeconf provider dsl-provider # DIRECT auto p2p2 iface p2p2 inet dhcp ifconfig: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 p2p1 Link encap:Ethernet inet6 addr: fe80::20a:ebff:fe21:99c6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 p2p2 Link encap:Ethernet inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20a:ebff:fe17:1249/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ppp0 Link encap:Point-to-Point Protocol inet addr:53.193.231.167 P-t-P:53.193.224.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 10.0.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 53.193.224.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 p2p2 By default, only ppp0 works. If I run "route add default gw 192.168.1.1 p2p2" then I can use p2p2 but ppp0 stops working. If I then run "route add default gw 53.193.224.1 ppp0" then I can use ppp0 again but p2p2 stops working. What can I do to be able to use both interfaces selectively?

  Read the article

• Export NFS path containing "-" (dash)

  - by qdot

  I'm in a bit of a pinch with NFS exports file. Specifically, I can't find a way to export a directory containing "-" in the path name. Manual (exports(5)) states: Also, each line may have one or more specifications for default options after the path name, in the form of a dash ("-") followed by an option list. The option list is used for all subsequent exports on that line only. It then states: If an export name contains spaces it should be quoted using double quotes. You can also specify spaces or other unusual character in the export name using a backslash followed by the character code as three octal digits. Unfortunately, that is not the case. Specifically, if the pathname contains "-", either verbatim, or with \055 or is enclosed in double quotes, it still refers to the name without "-" Any ideas? I have a large number of directories, all of the form /vol/buildsystem-s3c2440 /vol/buildsystem-tao3530 and I'd prefer to have them all available as nfs exports. Short of replacing the "-" with "_" everywhere in the scripts, can it be done with "-" ?

  Read the article

• Making hosts accessible between LAN subnets

  - by nixnotwin

  I have two inerfaces on my router with tomato firmwre: br0 and vlan4. br0 is on 192.168.0.0/16 subnet and vlan4 on 10.0.1.0/24 subnet. As I don't want the different network services on br0 available on vlan4, I have added this firewall rule: iptables -I INPUT -i vlan4 -j ACCEPT; iptables -I FORWARD -i vlan4 -o vlan2 -m state --state NEW -j ACCEPT; iptables -I FORWARD -i br0 -o vlan4 -j DROP; vlan2 is my WAN (internet acess). The issue that I want to solve is that I want to make one host from 192.168.0.0/16 network (br0), which has ip 192.168.0.50, available on vlan4 (10.0.1.0/24). Only that host should be available on vlan4 (and all other hosts on br0 should be inaccessible). What firewall rules can be used to do it? Edit 1: Output of iptables -nvL FORWARD: Chain FORWARD (policy DROP 4 packets, 204 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- vlan4 192.168.0.50 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- vlan4 ppp0 0.0.0.0/0 0.0.0.0/0 state NEW 229 13483 ACCEPT all -- vlan4 vlan2 0.0.0.0/0 0.0.0.0/0 state NEW 0 0 DROP all -- br0 vlan3 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- vlan3 ppp0 0.0.0.0/0 0.0.0.0/0 state NEW 67 3405 ACCEPT all -- vlan3 vlan2 0.0.0.0/0 0.0.0.0/0 state NEW 0 0 ACCEPT all -- br0 br0 0.0.0.0/0 0.0.0.0/0 34 1360 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID 758 40580 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU 11781 2111K restrict all -- * vlan2 0.0.0.0/0 0.0.0.0/0 26837 19M ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 wanin all -- vlan2 * 0.0.0.0/0 0.0.0.0/0 287 15927 wanout all -- * vlan2 0.0.0.0/0 0.0.0.0/0 283 15723 ACCEPT all -- br0 * 0.0.0.0/0 0.0.0.0/0 0 0 upnp all -- vlan2 * 0.0.0.0/0 0.0.0.0/0 Output of iptables -t nat -nvL PREROUTING: Chain PREROUTING (policy ACCEPT 6887 packets, 526K bytes) pkts bytes target prot opt in out source destination 855 83626 WANPREROUTING all -- * * 0.0.0.0/0 222.228.137.223 0 0 DROP all -- vlan2 * 0.0.0.0/0 192.168.0.0/16 0 0 DNAT udp -- * * 192.168.0.0/16 !192.168.0.0/16 udp dpt:53 to:192.168.0.1

  Read the article

• How can find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• Two identical fiber optic broadband lines working as one

  - by Katafalkas

  I have been trying to find an answer to this, but all I can find is hobbyists trying to connect their Linksys devices to get some magic out of them. I am looking for a way I could combine two 100Mbit fiber optic lines into a single connection for our office. I assume it involves some Cisco learning or something similar. Do I need to configure some big router to load-balance the NATing in some way? I assume that many of you have done something similar and hope someone could share their knowledge or at least provide me some tips on how to do this.

  Read the article

• Different versions of iperf for windows give totally different results

  - by Albert Mata

  Measuring TCP output from a Windows client to Solaris server: WXP SP3 with iperf 1.7.0 -- returns an average around 90Mbit Same client, same server but iperf 2.0.5 for windows -- returns an average of 8.5 Mbit Similar discrepancies have been observed connecting to other servers (W2008, W2003) It's difficult to get to some conclusions when different versions of the same tool provide vastly different results. Example below: C:\tempiperf -v (from iperf.fr) iperf version 2.0.5 (08 Jul 2010) pthreads C:\tempiperf -c solaris10 Client connecting to solaris10, TCP port 5001 TCP window size: 64.0 KByte (default) [ 3] local 10.172.181.159 port 2124 connected with 10.172.180.209 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.2 sec 10.6 MBytes 8.74 Mbits/sec Abysmal perfomance, but now I test from the same host (Windows XP SP3 32bit and 100Mbit) to the same server (Solaris 10/sparc 64bit and 1Gbit running iperf 2.0.5 with default window of 48k) with the old iperf C:\temp1iperf -v iperf version 1.7.0 (13 Mar 2003) win32 threads C:\temp1iperf.exe -c solaris10 -w64k Client connecting to solaris10, TCP port 5001 TCP window size: 64.0 KByte [1208] local 10.172.181.159 port 2128 connected with 10.172.180.209 port 5001 [ ID] Interval Transfer Bandwidth [1208] 0.0-10.0 sec 112 MBytes 94.0 Mbits/sec So one iperf with a 64k window says 8.75Mbit and the old iperf with the same window size says 94.0Mbit. These results are constant through repeated tests. From my testing launching iperf(old) with window size "x" and iperf(new) with window size "x" instead of producing the same or very close results produce totally different results. The only difference I see is the old compiled as win32 threads vs. pthreads but parallelism (-P 10) appears to work in both. Anyone has a clue or can recommend a tool that gives results I can trust?? EDIT: Looking at traces from (old) iperf it sets the TCP Window Scale flag to 3 in the SYN packet, when I run the (new) iperf this is set to 0 in the initial packet. A quick analysis of the window size through the exchange shows the (old) iperf moving back and forth but mostly at 32k while the (new) iperf mostly keeps at 64k. Maybe it will help somebody to connect the dots.

  Read the article

• What keeps you from changing your public IP address and wreak havok?

  - by Whitemage

  An interesting question was asked to me and I did not know what to answer.. So I'll ask here. Let's say I subscribed to an ISP and I'm using cable internet access. ISP gives me a public IP address of 60.61.62.63. What keeps me from changing this IP address to, let's say, 60.61.62.75 and mess with another consumer's internet access? For the sake of this argument, let's say that this other IP address is also owned by the same ISP. Also, let's assume that it's possible for me to go into the cable modem settings and manually change the IP address. Under a business contract where you are allocated static addresses, you are also assigned a default gaetway, a network address and a broadcast address. So that's 3 addresses the ISP "loses" to you. That seems very wastefull for dynamically assigned IP addresses where the majority of customers are.. Could they simply be using static arps? ACLs? Other simple mechanisms? Anyone who worked at an ISP would be willing to explain this a bit?

  Read the article

• Connecting Small business network to Azure Site to Site VPN

  - by MarkKGreenway

  Would like to have connectivity between azure virtual machines and on LAN users. My current network has a Cisco ISA550 connected to the WAN (one Ethernet cable into the office the fiber transceiver is on a different floor)and any public servers can be one-to one NAT-ed to have a public and private IP. What is the best way to get a reliable connection. Between end users and the cloud? I want to know the preferred on site endpoint. Do the azure vm's have to have a local ip in the LAN subnet? (Right now 10.10.0.0/20 or 255.255.240.0 to give room if this is the case). If in purchased an asa550 would I put it behind or in front of the isa550. Would it be ahead or peer with the users switches? What is the best way to get a reliable connection. Between end users and the cloud servers?

  Read the article

• wireless internet in linux is very very slow... but in windows.... everythnings fine

  - by Cody Acer

  yesterday when i was connecting to our neighbors wifi connection which is the signal strength is below 50%, i cant browse anything... even ping to gateway. 100% packet loss, and sometimes.. i can connect awesomely i can open my facebook account for 15 minutes but after 15min.. connection is extremely slow. but not windows i can surf even the signal str is very poor weird ey??.. root@Emely:~# lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx DMI Bridge [8086:a010] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a011] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: i915 Kernel modules: i915 00:02.1 Display controller [0380]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a012] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] 00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 2 [8086:27d2] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 3 [8086:27d4] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 4 [8086:27d6] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: ehci-pci 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: lpc_ich Kernel modules: lpc_ich 00:1f.2 SATA controller [0106]: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel modules: i2c-i801 05:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01) Subsystem: Wistron NeWeb Corp. Device [185f:051a] Kernel driver in use: bcma-pci-bridge Kernel modules: bcma 09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: sky2 Kernel modules: sky2 root@Emely:~# ip addr show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether e8:11:32:2e:a6:fd brd ff:ff:ff:ff:ff:ff 3: wlan0: mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:1b:b1:a9:ac:e0 brd ff:ff:ff:ff:ff:ff inet 192.168.1.108/24 brd 192.168.1.255 scope global wlan0 inet6 fe80::21b:b1ff:fea9:ace0/64 scope link valid_lft forever preferred_lft forever root@Emely:~# ip link show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether e8:11:32:2e:a6:fd brd ff:ff:ff:ff:ff:ff 3: wlan0: mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:1b:b1:a9:ac:e0 brd ff:ff:ff:ff:ff:ff root@Emely:~# rfkill list all 0: samsung-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: samsung-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no 3: phy0: Wireless LAN Soft blocked: no Hard blocked: no is this a wireless driver issue?

  Read the article

• Multiple VLAN on one switch port

  - by Macropus

  I have a HP ProCurve 1810G-8 which I currently use as a normal switch between 3 servers and a firewall. 2 of the servers are ESXi hosts, and one is a Nexentastor box with 2 iSCSI target LUNs. As the iSCSI traffic is on the same LAN as all other traffic, I would like to switch this to use a SAN for iSCSI traffic and the LAN for all other traffic. The Nexentastor box only has 2 NICs, and as such, with a physical arrangement, I presume that one must be plugged into the SAN VLAN and one on the LAN VLAN ports of the switch. Is there a way to have multiple VLANs over the same port? e.g. the Nexentsator box has 2 NICs, both plugged into the switch, both ports with access to both of the VLANs?

  Read the article

• MikroTik ipv6 Tunnel

  - by MikeSmitty

  I've got a MikroTik router set up with the latest stable OS on it, and I just set up an ipv6 tunnel with Hurricane Electric, but I'm having an odd issue with it. I can't ping anything until I first ping the tunnel endpoint on HE's side. After that I can ping any ipv6 address fine, but give it a little time (say, maybe 30 sec) and I can't ping any ipv6 addresses again. Whenever it stops allowing ping to go through I notice the counter on my firewall rule that drops invalid connections goes up. this is my ipv6 firewall config: add action=accept chain=input comment="" connection-state=established \ disabled=no in-interface=sit1 add action=accept chain=input comment="" connection-state=related disabled=no \ in-interface=sit1 add action=accept chain=input comment="" disabled=no in-interface=bridge \ src-address=ipv6_address_here/64 add action=drop chain=input comment="" connection-state=invalid disabled=no \ in-interface=sit1 add action=drop chain=input comment="" disabled=no in-interface=sit1 Any ideas on what it could be?

  Read the article

• rhel/centos vs. ubuntu (possibly other debian-based systems) linux in handling duplicate ips in the same subnet

  - by johnshen64

  This has bothered me for quite a while but I never found out why or how to change the behavior. ip duplicates could be caused by typos or dhcp errors etc., but they do occur from time to time. in rpm-based systems such as centos, the old server with the duplicate ip wins, and the new server will get an error in bringing up the nic (ip address already used). this is somewhat harmless because we can just fix the system that is coming up. ubuntu only the other hand happily grabs the used ip for itself and leave the old server/device without a valid ip. this is the more dangerous behavior because it causes outages. what i want is to change the ubuntu behavior to that of the centos/rhel so would appreciate any help.

  Read the article

• Glusterfs : 'No route to host' for fstab mount in CentOS

  - by son_of_fire

  I am using glusterfs, and am using fstab in this way: <IPADDRESS>:/<VOLUMENAME> /some/mount/point glusterfs defaults,_netdev 0 0 but the logs for the mount continue to say the following. [<TIMESTAMP>] E [socket.c:2161:socket_connect_finish] 0-<VOLUMENAME>-client-1: connection to <IPADDRESS>:24007 failed (No route to host) I know this is not true, since when the system is up and running, I can easily issue a mount and the volume gets mounted. (I've done this by using rc.local) after reading more I have seen that using _netdev is preferred, and that if the host cannot be reached netfs will remount the volume after the network comes up, but that is not happening. (netfs is running). Is there a way to make the mount happen at a different time without using a script? (I would prefer to use fstab to manage the mounting even though I can use a script.)

  Read the article

• I am trying to set up a ubuntu sever 12.04 on my machine [migrated]

  - by Jseb

  I am trying to set up a server on my home network which will eventually host rails. I am not great in linux server and i try to follow the prompt. I did succesfully get to a black screen which then prompts me to a username then password to then do anything ( assuming). However here what i try to do I kinda fellow his tutorial http://www.ubuntugeek.com/step-by-step-ubuntu-11-04-natty-lamp-server-setup.html but however the command where not 100% like him not in same order but same idea. Then i want to install ubuntu server with gui here the command i try with sudo apt-get upgrade sudo apt-get install ubuntu-desktop Which however give me the following error Err http... inRelease w Failed to fetch ht... So been ignored if i try the desktop one i get E: unable to locate package ubuntu E: unable to locate package desktop So i am assuming i am not connected to the internet, so i try the following command sudo vi /etc/network/interfaces here the output it gives me and i know my gateway on my laptop is 192.168.1.1 address: 192.168.1.148 netmask: 255.255.255.0 network: 192.168.1.0 broadcasts: 192.168.1.255 gateway: 192.168.1.1 Btw i do not know the command to get out of vi and saving it. Err http://us.archive.ubuntu.com precises InRelease Err http://us.archive.ubuntu.com precises-updates InRelease Err http://us.archive.ubuntu.com precises-backports InRelease Reading package lists... Done W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/precise/InRelease W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/precise-updates/InRelease W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/precise-backport/InRelease

  Read the article

• Sharing Windows 7 Hard drive with Windows XP Hard drive

  - by Ginzo Milani

  I wish to share my hard drives between my two computers but I seem to be running along some sort of error... my windows XP Computer is picking up my "XGaming" hard drive but when clicked it says access is denied, despite there is no password set up(I followed this: http://www.howtogeek.com/howto/windows-7/share-files-and-printers-between-windows-7-and-xp/) I also tried to share my C and J drives on my windows XP computer but my windows 7 computer doesn't seem to even detect them!

  Read the article

< Previous Page | 139 140 141 142 143 144 145 146 147 148 149 150  | Next Page >