virtualpc 2007 - Page 143

MacMini transmit rate stuck at 11, every other device can connect at full 54Mbit/s?

- by chum of chance

I have a MacMini circa 2007 that's getting very low transmit rates via wifi, 8-11. I have other devices that are getting full 54, including a MacBook Air. With everything else off, the MacMini doesn't want to seem to go any faster. Since it has been previously connected to ethernet its entire life, I was wondering if there were some settings I can change to speed up the connection. Option-clicking the network icon gives this read out: PHY Mode: 802.11g Channel: 1 (2.4 Ghz) Security: WPA2 Personal RSSI: -73 Transmit Rate: 11 My new MacBook Air has the following readout: PHY Mode: 802.11n Channel: 1 (2.4 Ghz) Security: WPA2 Personal RSSI: -66 Transmit Rate: 79 Both have full bars and the wireless router is in the same room to eliminate any obstructions from the equation. Could the MacMini be connecting at an older protocol, like 802.11b and be reporting erroneously that it is connected at 802.11g? This would explain why I haven't seen a transmit rate above 11. Any further trouble shooting I can try before buying a new USB 802.11n device? The WiFi router is a DLink DIR-615. I can see other devices, and none, even the other g connected devices, are getting below 30-40 MBit/s. What's going on here?

Read the article

Convert Public Folder to Shared Mailbox

- by Lilienthal

Due to a change in company policy, all existing Public Folders (PF) have to be phased out in favour of shared mailboxes. Unfortunately, they don't seem to have any procedures or guidelines for this migration and I can't find much online either. I've already migrated one of our public folders so far as a sort of test case. Because we still use Exchange 2003, we can't create real shared mailboxes as we would in 2007 or 2010 (With New-Mailbox -Shared ... in the Exchange Shell). Instead, I simply created a new account on the AD and assigned it a mailbox. I then set the PF's permissions to read-only to keep it in a consistent state and copied the entire folder to a local PST in Outlook 2010, from which the folder was in turn copied to the new mailbox. Permissions and Folder Visible were set for all users and the migration was successful. While this works, the whole procedure feels very hackish to me and not at all efficient. I'd welcome some input on automating or at least streamlining the process. Additionally, we are unsure of what to do with our mail-enabled Public Folders. Several of these are nested under other PFs, some of which are also mail-enabled. Preserving folder structure is a key requirement and this seems impossible at first glance. I've considered creating dummy accounts for all the email addresses from our mail-enabled PFs and then setting up automated rules to forward messages to a subfolder of the new shared mailboxes, but I am not familiar enough with Exchange to know if this is even possible. Further points of concern are the Calendars and Contact lists in our public folders. I suppose I'll be forced to create new mailboxes for every one of these we have as well, then set up share permissions for their Calendar and Contact items, but would be happy to be proven wrong.

Read the article

"No such file or directory"?

- by user1509541

Ok, so I have a VDS laying around, and I thought I would turn it into a TF2 game server. When I connect to my server through PuTTY, and use wget to download the package "hldsupdatetool.bin" from Steampowered.com. I go to run it and it says "No such file or directory found". When I use "ls" to see what files are in directory, it lists "hldsupdatetool.bin" as being in the directory. So, why is it saying it's not there? This has been a headache for the past 2 days. It's returning: root@10004:~# wget http://www.steampowered.com/download/hldsupdatetool.bin --2012-07-08 06:04:49-- http://www.steampowered.com/download/hldsupdatetool.bin Resolving www.steampowered.com... 208.64.202.68 Connecting to www.steampowered.com|208.64.202.68|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 3513408 (3.4M) [application/octet-stream] Saving to: “hldsupdatetool.bin.3” 100%[======================================>] 3,513,408 2.45M/s in 1.4s 2012-07-08 06:04:51 (2.45 MB/s) - “hldsupdatetool.bin.3” saved [3513408/3513408] root@10004:~# chmod +x hldsupdatetool.bin.3 root@10004:~# ./hldsupdatetool.bin.3 -bash: ./hldsupdatetool.bin.3: No such file or directory root@10004:~# More: root@10004:~# ls ffmpeg-packages hldsupdatetool.bin.1 hldsupdatetool.bin.3 hldsupdatetool.bin hldsupdatetool.bin.2 setup.sh root@10004:~# ls -la total 13828 drwx------ 4 root root 4096 Jul 8 06:04 . drwxr-xr-x 21 root root 4096 Jul 8 05:57 .. -rw------- 1 root root 8799 Jul 8 06:26 .bash_history -rw-r--r-- 1 root root 570 Jan 31 2010 .bashrc -rw-r--r-- 1 root root 4 Jul 2 19:39 .custombuild drwxr-xr-x 2 root root 4096 Jul 4 18:49 ffmpeg-packages ---x--xrwx 1 root root 3513408 Sep 2 2005 hldsupdatetool.bin -rwxr-xr-x 1 root root 3513408 Sep 2 2005 hldsupdatetool.bin.1 -rw-r--r-- 1 root root 3513408 Sep 2 2005 hldsupdatetool.bin.2 -rwxr-xr-x 1 root root 3513408 Sep 2 2005 hldsupdatetool.bin.3 -rw-r--r-- 1 root root 140 Nov 19 2007 .profile -rw------- 1 root root 1024 Jul 2 19:49 .rnd -rwxr-xr-x 1 root root 38866 May 23 22:02 setup.sh drwxr-xr-x 2 root root 4096 Jul 2 19:44 .ssh root@10004:~#

Read the article

What are the side effects of disabling an Exchange mailbox?

- by Nic

When working with Exchange Server 2007 or newer, disabling a mailbox is a fairly common operation. However, the Technet documentation has no details about the side effects of disabling a mailbox. This is all it says. "This task removes all the Exchange attributes from the user object in Active Directory. Based on the deleted items retention policy, the Exchange store will retain mailbox data for the user object." Source: http://technet.microsoft.com/en-us/library/bb123730(v=exchg.141).aspx But is that all? Exchange mailboxes in the real world tend to be highly interconnected. Perhaps the boss has delegated calendar control to a secretary. Maybe a team of staff members all share access to a public folder. Perhaps a power user has been granted the ability to receive email at several different addresses. Two clear questions come to mind. What happens to links between mailboxes after a mailbox is disconnected? Can the Disable-Mailbox operation be easily undone?

Read the article

Diagnosing PC crashes (most often while using shared folders or torrents)

- by Dyppl

For the last few weeks my PC (pretty old P4 with WinXP SP3) has been crashing randomly. It just suddenly reboots instanteneously. It feels hardware-related but I wasn't able to determine wether it's software or hardware that causes it. I did notice a pattern though: it's more likely to crash when I copy a lot of files over network or have uTorrent running, but sometimes it crashes when I am not doing anything with it. Copying files from it over network causes it to crash in 1 to 10 minutes almost every time. Using torrents causes it to crash every 1-3 hours. With neither or that on it crashes every 24 hours or so. I ruled out the following probable causes: PSU (I bought a new one and turned off most of the drives so the power is sufficient 100%) Bad HDD or interface cable on my SATA disk from which I was originally copying the data over network (bought new SATA cable and later yanked out the HDD completely, PC still crashes without it) Video adapter (AGP slot is now empty, using the onboard VGA at the moment) Network adapter (removed it from PCI, using onboard LAN) CPU (I think: I changed the termopaste and it's temperature is below 50C) RAM (I think: I ran Memtest86 and it didn't show any errors) At the moment I only have only one system HDD and DVD drives, a mouse and a keyboard plugged in. The fact that it crashes most often when I use network extensively makes me think that maybe it's software related (I removed the network adapter from PCI and now am using an onboard one, so network hardware is unlikely to cause problems). I am now pondering system reinstall but it's not a pleasant solution so I decided to ask wether there are better ideas first. If someone can share a good diagnostic tool it would be great because I didn't find anything good. Thanks in advance, I hope that "help to diagnose" questions aren't entirely banned here. EDIT: Motherboard is actually ~4 years old as I replaced it back in 2007

Read the article

Unnecessary Error Message Being Displayed

- by ThatMacLad

I've set up a form to update my blog and it was working fine up until about this morning. It keeps on turning up with an Invalid Entry ID error on the edit post page when I click the update button despite the fact that it updates the homepage. All help is seriously appreciated. <html> <head> <title>Ultan's Blog | New Post</title> <link rel="stylesheet" href="css/editpost.css" type="text/css" /> </head> <body> <div class="new-form"> <div class="header"> </div> <div class="form-bg"> <?php mysql_connect ('localhost', 'root', 'root') ; mysql_select_db ('tmlblog'); if (isset($_POST['update'])) { $id = htmlspecialchars(strip_tags($_POST['id'])); $month = htmlspecialchars(strip_tags($_POST['month'])); $date = htmlspecialchars(strip_tags($_POST['date'])); $year = htmlspecialchars(strip_tags($_POST['year'])); $time = htmlspecialchars(strip_tags($_POST['time'])); $entry = $_POST['entry']; $title = htmlspecialchars(strip_tags($_POST['title'])); if (isset($_POST['password'])) $password = htmlspecialchars(strip_tags($_POST['password'])); else $password = ""; $entry = nl2br($entry); if (!get_magic_quotes_gpc()) { $title = addslashes($title); $entry = addslashes($entry); } $timestamp = strtotime ($month . " " . $date . " " . $year . " " . $time); $result = mysql_query("UPDATE php_blog SET timestamp='$timestamp', title='$title', entry='$entry', password='$password' WHERE id='$id' LIMIT 1") or print ("Can't update entry.<br />" . mysql_error()); header("Location: post.php?id=" . $id); } if (isset($_POST['delete'])) { $id = (int)$_POST['id']; $result = mysql_query("DELETE FROM php_blog WHERE id='$id'") or print ("Can't delete entry.<br />" . mysql_error()); if ($result != false) { print "The entry has been successfully deleted from the database."; exit; } } if (!isset($_GET['id']) || empty($_GET['id']) || !is_numeric($_GET['id'])) { die("Invalid entry ID."); } else { $id = (int)$_GET['id']; } $result = mysql_query ("SELECT * FROM php_blog WHERE id='$id'") or print ("Can't select entry.<br />" . $sql . "<br />" . mysql_error()); while ($row = mysql_fetch_array($result)) { $old_timestamp = $row['timestamp']; $old_title = stripslashes($row['title']); $old_entry = stripslashes($row['entry']); $old_password = $row['password']; $old_title = str_replace('"','\'',$old_title); $old_entry = str_replace('<br />', '', $old_entry); $old_month = date("F",$old_timestamp); $old_date = date("d",$old_timestamp); $old_year = date("Y",$old_timestamp); $old_time = date("H:i",$old_timestamp); } ?> <form method="post" action="<?php echo $_SERVER['PHP_SELF']; ?>"> <p><input type="hidden" name="id" value="<?php echo $id; ?>" /> <strong><label for="month">Date (month, day, year):</label></strong> <select name="month" id="month"> <option value="<?php echo $old_month; ?>"><?php echo $old_month; ?></option> <option value="January">January</option> <option value="February">February</option> <option value="March">March</option> <option value="April">April</option> <option value="May">May</option> <option value="June">June</option> <option value="July">July</option> <option value="August">August</option> <option value="September">September</option> <option value="October">October</option> <option value="November">November</option> <option value="December">December</option> </select> <input type="text" name="date" id="date" size="2" value="<?php echo $old_date; ?>" /> <select name="year" id="year"> <option value="<?php echo $old_year; ?>"><?php echo $old_year; ?></option> <option value="2004">2004</option> <option value="2005">2005</option> <option value="2006">2006</option> <option value="2007">2007</option> <option value="2008">2008</option> <option value="2009">2009</option> <option value="2010">2010</option> </select> <strong><label for="time">Time:</label></strong> <input type="text" name="time" id="time" size="5" value="<?php echo $old_time; ?>" /></p> <p><strong><label for="title">Title:</label></strong> <input type="text" name="title" id="title" value="<?php echo $old_title; ?>" size="40" /> </p> <p><strong><label for="password">Password protect?</label></strong> <input type="checkbox" name="password" id="password" value="1"<?php if($old_password == 1) echo " checked=\"checked\""; ?> /></p> <p><textarea cols="80" rows="20" name="entry" id="entry"><?php echo $old_entry; ?></textarea></p> <p><input type="submit" name="update" id="update" value="Update"></p> </form> <p><strong>Be absolutely sure that this is the post that you wish to remove from the blog!</strong><br /> </p> <form action="<?php echo $_SERVER['PHP_SELF']; ?>" method="post"> <input type="hidden" name="id" id="id" value="<?php echo $id; ?>" /> <input type="submit" name="delete" id="delete" value="Delete" /> </form> </div> </div> </div> <div class="bottom"></div> </body> </html>

Read the article

PHP 'Years' array

- by J M 4

I am trying to create an array for years which i will use in the DOB year piece of a form I am building. Currently, I know there are two ways to handle the issue but I don't really care for either: 1) Range: I know I can create a year array using the following <?php $year = range(1910,date("Y")); $_SESSION['years_arr'] = $year; ?> the problem with Point 1 is two fold: a) my function call shows the first year as 'selected' instead of "Year" as I have as option="0", and b) I want the years reversed so 2010 is the first in the least and shown decreasing. My function call is: PHP <?php function showOptionsDrop($array, $active, $echo=true){ $string = ''; foreach($array as $k => $v){ $s = ($active == $k)? ' selected="selected"' : ''; $string .= '<option value="'.$k.'"'.$s.'>'.$v.'</option>'."\n"; } if($echo) echo $string; else return $string; } ?> HTML <table> <tr> <td>State:</td> <td><select name="F1State"><option value="0">Choose a year</option><?php showOptionsDrop($_SESSION['years_arr'], null, true); ?></select> </td> </tr> </table> 2) Long Array I know i can physically create an array with years listed out but this takes up a lot of space and time if I ever want to go back and modify. ex: PHP $years = array('1900'=>"1900", '1901'=>"1901", '1902'=>"1902", '1903'=>"1903", '1904'=>"1904", '1905'=>"1905", '1906'=>"1906", '1907'=>"1907", '1908'=>"1908", '1909'=>"1909", '1910'=>"1910", '1911'=>"1911", '1912'=>"1912", '1913'=>"1913", '1914'=>"1914", '1915'=>"1915", '1916'=>"1916", '1917'=>"1917", '1918'=>"1918", '1919'=>"1919", '1920'=>"1920", '1921'=>"1921", '1922'=>"1922", '1923'=>"1923", '1924'=>"1924", '1925'=>"1925", '1926'=>"1926", '1927'=>"1927", '1928'=>"1928", '1929'=>"1929", '1930'=>"1930", '1931'=>"1931", '1932'=>"1932", '1933'=>"1933", '1934'=>"1934", '1935'=>"1935", '1936'=>"1936", '1937'=>"1937", '1938'=>"1938", '1939'=>"1939", '1940'=>"1940", '1941'=>"1941", '1942'=>"1942", '1943'=>"1943", '1944'=>"1944", '1945'=>"1945", '1946'=>"1946", '1947'=>"1947", '1948'=>"1948", '1949'=>"1949", '1950'=>"1950", '1951'=>"1951", '1952'=>"1952", '1953'=>"1953", '1954'=>"1954", '1955'=>"1955", '1956'=>"1956", '1957'=>"1957", '1958'=>"1958", '1959'=>"1959", '1960'=>"1960", '1961'=>"1961", '1962'=>"1962", '1963'=>"1963", '1964'=>"1964", '1965'=>"1965", '1966'=>"1966", '1967'=>"1967", '1968'=>"1968", '1969'=>"1969", '1970'=>"1970", '1971'=>"1971", '1972'=>"1972", '1973'=>"1973", '1974'=>"1974", '1975'=>"1975", '1976'=>"1976", '1977'=>"1977", '1978'=>"1978", '1979'=>"1979", '1980'=>"1980", '1981'=>"1981", '1982'=>"1982", '1983'=>"1983", '1984'=>"1984", '1985'=>"1985", '1986'=>"1986", '1987'=>"1987", '1988'=>"1988", '1989'=>"1989", '1990'=>"1990", '1991'=>"1991", '1992'=>"1992", '1993'=>"1993", '1994'=>"1994", '1995'=>"1995", '1996'=>"1996", '1997'=>"1997", '1998'=>"1998", '1999'=>"1999", '2000'=>"2000", '2001'=>"2001", '2002'=>"2002", '2003'=>"2003", '2004'=>"2004", '2005'=>"2005", '2006'=>"2006", '2007'=>"2007", '2008'=>"2008", '2009'=>"2009", '2010'=>"2010"); $_SESSION['years_arr'] = $years_arr; Does anybody have a recommended idea how to work - or just how to simply modify my existing code? Thank you!

Read the article

Share Files and Folders and Internet between Guest OS and the Host in Hyper-V

- by Manesh Karunakaran

For those who are familiar with the VirtualPC, vmWare and VirtualBox environments will be quite irritated to find out that there is no direct way to share files from the Host machine to the Virtualized guest environment. This is a good thing from a CIO perspective because there’s excellent isolation for the virtualized environments this way, but for the developer junkies like us, this is an irritant, especially for those who have nuked their Windows 7 OS and installed Windows Server 2008 R2 for all the the SharePoint friendliness that it offers. Here’s a quick 5 minutes howto on Enabling Shared Folders and Internet Access for the Hyper-V images, for those who are still struggling with this. Step 1: Add a Virtual Network Adapter to your Guest OS For this, shut down the guest machine, go to its settings and add a Virtual Network Adapter as given in the images below Step 2: Enable Virtual Networking in Hyper-V Setting this up is very easy. In the Hyper-V Manager, under Actions (right panel), click the Virtual Network Manager. In the Virtual Network Manager in the Create virtual network panel, select Internal and click the Add button. At this point if you open Control Panel\Network and Internet\Network Connections you will be able to see the new Network Adapter, Now name it to something meaningful other than Network Adapter X. Now you can add this network to each of your virtual machines, but at this point, unless you assign an IP address in each connection, you won't be able to do much. Step 3: Enable Internet Connection Sharing so that Guest OS’es also can connect to the internet. To enable ICS follow these steps: Click on the network icon in the tray of your host machine and select Network and Sharing Center. From there click Manage network connections. Select the network adapter that you use to access the Internet. Right click it and select Properties. In the properties dialog select the Sharing tab. On this tab check the box that says "Allow other network users..." and then set the Home networking connection to be the network adapter that was created above (now you see why I said to rename it to something useful). Now your virtual machines that have this network connection will automatically get an IP address and will be able to connect to the Internet (provided your internet connection is working). Because each adapter also gets an automatic address you can now share files and folders between your host and your virtual machines which is important since you can't just drag-and-drop files like you can with Virtual PC. Step 4: Create a Shared Folder in the Host Machine and use it in the Guest machine. Right click on the folder that you want to Share and select ‘Share with\Specific People’ and specify who all can access the share. Open the Guest OS from Hyper V Navigate to Start > Run and type in the Address of the Share (Or Map a Drive to the Share) Bingo! The Share opens!! :) Now you can share as many files and folders as you want between the host and the guest, and you also have internet access inside the Virtual machines. Hope that helps. Technorati Tags: Shared folder,Hyper-V,Share Files,Share files and folders between guest and host,Hyper-V Networking,Share Internet Access in Hyper-V,Internet,Files,Shared folders in Hyper-V

Read the article

I don't understand how work call_once

- by SABROG

Please help me understand how work call_once Here is thread-safe code. I don't understand why this need Thread Local Storage and global_epoch variables. Variable _fast_pthread_once_per_thread_epoch can be changed to constant/enum like {FAST_PTHREAD_ONCE_INIT, BEING_INITIALIZED, FINISH_INITIALIZED}. Why needed count calls in global_epoch? I think this code can be rewriting with logc: if flag FINISH_INITIALIZED do nothing, else go to block with mutexes and this all. #ifndef FAST_PTHREAD_ONCE_H #define FAST_PTHREAD_ONCE_H #include #include typedef sig_atomic_t fast_pthread_once_t; #define FAST_PTHREAD_ONCE_INIT SIG_ATOMIC_MAX extern __thread fast_pthread_once_t _fast_pthread_once_per_thread_epoch; #ifdef __cplusplus extern "C" { #endif extern void fast_pthread_once( pthread_once_t *once, void (*func)(void) ); inline static void fast_pthread_once_inline( fast_pthread_once_t *once, void (*func)(void) ) { fast_pthread_once_t x = *once; /* unprotected access */ if ( x _fast_pthread_once_per_thread_epoch ) { fast_pthread_once( once, func ); } } #ifdef __cplusplus } #endif #endif FAST_PTHREAD_ONCE_H Source fast_pthread_once.c The source is written in C. The lines of the primary function are numbered for reference in the subsequent correctness argument. #include "fast_pthread_once.h" #include static pthread_mutex_t mu = PTHREAD_MUTEX_INITIALIZER; /* protects global_epoch and all fast_pthread_once_t writes */ static pthread_cond_t cv = PTHREAD_COND_INITIALIZER; /* signalled whenever a fast_pthread_once_t is finalized */ #define BEING_INITIALIZED (FAST_PTHREAD_ONCE_INIT - 1) static fast_pthread_once_t global_epoch = 0; /* under mu */ __thread fast_pthread_once_t _fast_pthread_once_per_thread_epoch; static void check( int x ) { if ( x == 0 ) abort(); } void fast_pthread_once( fast_pthread_once_t *once, void (*func)(void) ) { /*01*/ fast_pthread_once_t x = *once; /* unprotected access */ /*02*/ if ( x _fast_pthread_once_per_thread_epoch ) { /*03*/ check( pthread_mutex_lock(µ) == 0 ); /*04*/ if ( *once == FAST_PTHREAD_ONCE_INIT ) { /*05*/ *once = BEING_INITIALIZED; /*06*/ check( pthread_mutex_unlock(µ) == 0 ); /*07*/ (*func)(); /*08*/ check( pthread_mutex_lock(µ) == 0 ); /*09*/ global_epoch++; /*10*/ *once = global_epoch; /*11*/ check( pthread_cond_broadcast(&cv;) == 0 ); /*12*/ } else { /*13*/ while ( *once == BEING_INITIALIZED ) { /*14*/ check( pthread_cond_wait(&cv;, µ) == 0 ); /*15*/ } /*16*/ } /*17*/ _fast_pthread_once_per_thread_epoch = global_epoch; /*18*/ check (pthread_mutex_unlock(µ) == 0); } } This code from BOOST: #ifndef BOOST_THREAD_PTHREAD_ONCE_HPP #define BOOST_THREAD_PTHREAD_ONCE_HPP // once.hpp // // (C) Copyright 2007-8 Anthony Williams // // Distributed under the Boost Software License, Version 1.0. (See // accompanying file LICENSE_1_0.txt or copy at // http://www.boost.org/LICENSE_1_0.txt) #include #include #include #include "pthread_mutex_scoped_lock.hpp" #include #include #include namespace boost { struct once_flag { boost::uintmax_t epoch; }; namespace detail { BOOST_THREAD_DECL boost::uintmax_t& get_once_per_thread_epoch(); BOOST_THREAD_DECL extern boost::uintmax_t once_global_epoch; BOOST_THREAD_DECL extern pthread_mutex_t once_epoch_mutex; BOOST_THREAD_DECL extern pthread_cond_t once_epoch_cv; } #define BOOST_ONCE_INITIAL_FLAG_VALUE 0 #define BOOST_ONCE_INIT {BOOST_ONCE_INITIAL_FLAG_VALUE} // Based on Mike Burrows fast_pthread_once algorithm as described in // http://www.open-std.org/jtc1/sc22/wg21/docs/papers/2007/n2444.html template void call_once(once_flag& flag,Function f) { static boost::uintmax_t const uninitialized_flag=BOOST_ONCE_INITIAL_FLAG_VALUE; static boost::uintmax_t const being_initialized=uninitialized_flag+1; boost::uintmax_t const epoch=flag.epoch; boost::uintmax_t& this_thread_epoch=detail::get_once_per_thread_epoch(); if(epoch #endif I right understand, boost don't use atomic operation, so code from boost not thread-safe?

Read the article

news feed using .Net Dataservices / OData / Atom ?

- by Stephan

Let's say I have an web CMS type application, and an EDM model with an entity called 'article', and I need to offer the ability for client applications, to a read/query the articles (and other resources stored in our database) a straightforward syndication feed of these articles to end users (along the lines of a simple RSS feed) It seems to me that for the first task, and .net 4's dataservice would be perfect for the job. For the second case, I'm wondering (a) whether atom the right format to choose - I think it is - and (b) whether it's possible to achieve such a feed using the same ado.net OData service. I took a look at some of the examples out there and briefly set up a proof of concept: http://localhost/projectname/DataService.svc/Articles <?xml version="1.0" encoding="utf-8" standalone="yes"?> <feed xml:base="http://localhost/projectname/DataService.svc/" xmlns:d="http://schemas.microsoft.com/ado/2007/08/dataservices" xmlns:m="http://schemas.microsoft.com/ado/2007/08/dataservices/metadata" xmlns="http://www.w3.org/2005/Atom"> <title type="text">Articles</title> <id>http://localhost/projectname/DataService.svc/Articles</id> <updated>2010-05-21T09:41:22Z</updated> <link rel="self" title="Articles" href="Articles" /> <entry> <id>http://---------DataService.svc/Articles(1)</id> <title type="text"></title> <updated>2010-05-21T09:41:22Z</updated> <author> <name /> </author> <link rel="edit" title="Article" href="Articles(1)" /> <category term="Model1.Article" scheme="http://schemas.microsoft.com/ado/2007/08/dataservices/scheme" /> <content type="application/xml"> <m:properties> <d:int_ContentID m:type="Edm.Int32">1</d:int_ContentID> <d:Titel>hello world</d:Titel> <d:Source>http://www.google.com</d:Source> </m:properties> </content> </entry> </feed> and noticed that, though the feed works and items are showing up, the title tag on the entry level is left blank. (as a result, when you check this feed in a feed reader, you will see no title). I searched msdn but haven't found a way to do that, but it should be possible. Stackoverflow itself uses an atom feed in that fashion, so it should be possible. Right? So I suppose my question is; Is there a way to make the ado.net dataservice Atom feed look like something suitable for your average news feed reader? - OR, am I using the wrong tool for the wrong purposes, and should I be looking elsewhere (.net syndication API's perhaps)?

Read the article

SQLAuthority News – Interview with SQL Server MVP Madhivanan – A Real Problem Solver

- by pinaldave

Madhivanan (SQL Server MVP) is a real community hero. He is known for his two skills – 1) Help Community and 2) Help Community. I have met him many times and every time I feel if anybody in online world needs help Madhinvanan does his best to reach them out and solve problem. His name is not new if you are ready this blog or have ever asked a question in any online SQL forum. He is always there to help. When Madhivanan has time he even helps people on this blog as well. He spends his valuable time to help community only. He recently crossed over 1000 helpful comments on this blog. On that occasion, I have interviewed him to find out if he has any life outside SQL. Q 1. Tell us something about your self. I am Madhivanan ,an MSc computer Science graduate from Chennai, India and working as a Lead Analyst-Project at Ellaar Infotek Solutions Private Limited. I am basically a developer started with Visual Basic 6.0, SQL Server 2000 and Crystal Report 8. As years go on I started working more on writing queries in SQL Server in most of the projects developed in my company. I have some good level of knowledge in ORACLE, MySQL and PostgreSQL as well. Now I am leading a project develeoped in Windows Azure. Q 2. What motivates you to help people on community and forums. When I got some errors during the application development in my early days of my career, I got good solutions from online forums and weblogs. So I decided to help others if possible. When I visit forums and help people if I know the answer to the questions. I am one of the leading posters at www.sqlteam.com and also a moderator at www.sql-server-performance.com. I also take part in Visual Basic and Crystal Reports forums. I have been SQL Server MVP since 2007. Q 3. Your personal life is not much known. Tell us something about your personal life. I am happily married person. My wife is a B.Pharm graduate. I have a son who is now 18 months old. Q 4. Where can we read further for your community activity. I have a blog at http://beyondrelational.com/blogs/madhivanan where you can find most of my T-sql stuffs Q 5. When not working with SQL what do you do? When not working with SQL, I spend time playing with my son, reading some magazines and watching TV. Madhivanan for your work and help to community, a true salute to you. Hats off my friend. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: MVP, Readers Contribution, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

Read the article

This Week in Geek History: Gmail Goes Public, Deep Blue Wins at Chess, and the Birth of Thomas Edison

- by Jason Fitzpatrick

Every week we bring you a snapshot of the week in Geek History. This week we’re taking a peek at the public release of Gmail, the first time a computer won against a chess champion, and the birth of prolific inventor Thomas Edison. Gmail Goes Public It’s hard to believe that Gmail has only been around for seven years and that for the first three years of its life it was invite only. In 2007 Gmail dropped the invite only requirement (although they would hold onto the “beta” tag for another two years) and opened its doors for anyone to grab a username @gmail. For what seemed like an entire epoch in internet history Gmail had the slickest web-based email around with constant innovations and features rolling out from Gmail Labs. Only in the last year or so have major overhauls at competitors like Hotmail and Yahoo! Mail brought other services up to speed. Can’t stand reading a Week in Geek History entry without a random fact? Here you go: gmail.com was originally owned by the Garfield franchise and ran a service that delivered Garfield comics to your email inbox. No, we’re not kidding. Deep Blue Proves Itself a Chess Master Deep Blue was a super computer constructed by IBM with the sole purpose of winning chess matches. In 2011 with the all seeing eye of Google and the amazing computational abilities of engines like Wolfram Alpha we simply take powerful computers immersed in our daily lives for granted. The 1996 match against reigning world chest champion Garry Kasparov where in Deep Blue held its own, but ultimately lost, in a 4-2 match shook a lot of people up. What did it mean if something that was considered such an elegant and quintessentially human endeavor such as chess was so easy for a machine? A series of upgrades helped Deep Blue outright win a match against Kasparov in 1997 (seen in the photo above). After the win Deep Blue was retired and disassembled. Parts of Deep Blue are housed in the National Museum of History and the Computer History Museum. Birth of Thomas Edison Thomas Alva Edison was one of the most prolific inventors in history and holds an astounding 1,093 US Patents. He is responsible for outright inventing or greatly refining major innovations in the history of world culture including the phonograph, the movie camera, the carbon microphone used in nearly every telephone well into the 1980s, batteries for electric cars (a notion we’d take over a century to take seriously), voting machines, and of course his enormous contribution to electric distribution systems. Despite the role of scientist and inventor being largely unglamorous, Thomas Edison and his tumultuous relationship with fellow inventor Nikola Tesla have been fodder for everything from books, to comics, to movies, and video games. Other Notable Moments from This Week in Geek History Although we only shine the spotlight on three interesting facts a week in our Geek History column, that doesn’t mean we don’t have space to highlight a few more in passing. This week in Geek History: 1971 – Apollo 14 returns to Earth after third Lunar mission. 1974 – Birth of Robot Chicken creator Seth Green. 1986 – Death of Dune creator Frank Herbert. Goodnight Dune. 1997 – Simpsons becomes longest running animated show on television. Have an interesting bit of geek trivia to share? Shoot us an email to [email protected] with “history” in the subject line and we’ll be sure to add it to our list of trivia. Latest Features How-To Geek ETC Here’s a Super Simple Trick to Defeating Fake Anti-Virus Malware How to Change the Default Application for Android Tasks Stop Believing TV’s Lies: The Real Truth About "Enhancing" Images The How-To Geek Valentine’s Day Gift Guide Inspire Geek Love with These Hilarious Geek Valentines RGB? CMYK? Alpha? What Are Image Channels and What Do They Mean? Clean Up Google Calendar’s Interface in Chrome and Iron The Rise and Fall of Kramerica? [Seinfeld Video] GNOME Shell 3 Live CDs for OpenSUSE and Fedora Available for Testing Picplz Offers Special FX, Sharing, and Backup of Your Smartphone Pics BUILD! An Epic LEGO Stop Motion Film [VIDEO] The Lingering Glow of Sunset over a Winter Landscape Wallpaper

Read the article

Configuring Fed Authentication Methods in OIF / IdP

- by Damien Carru

In this article, I will provide examples on how to configure OIF/IdP to map OAM Authentication Schemes to Federation Authentication Methods, based on the concepts introduced in my previous entry. I will show examples for the three protocols supported by OIF: SAML 2.0 SSO SAML 1.1 SSO OpenID 2.0 Enjoy the reading! Configuration As I mentioned in my previous article, mapping Federation Authentication Methods to OAM Authentication Schemes is protocol dependent, since the methods are defined in the various protocols (SAML 2.0, SAML 1.1, OpenID 2.0). As such, the WLST commands to set those mappings will involve: Either the SP Partner Profile and affect all Partners referencing that profile, which do not override the Federation Authentication Method to OAM Authentication Scheme mappings Or the SP Partner entry, which will only affect the SP Partner It is important to note that if an SP Partner is configured to define one or more Federation Authentication Method to OAM Authentication Scheme mappings, then all the mappings defined in the SP Partner Profile will be ignored. WLST Commands The two OIF WLST commands that can be used to define mapping Federation Authentication Methods to OAM Authentication Schemes are: addSPPartnerProfileAuthnMethod() to define a mapping on an SP Partner Profile, taking as parameters: The name of the SP Partner Profile The Federation Authentication Method The OAM Authentication Scheme name addSPPartnerAuthnMethod() to define a mapping on an SP Partner , taking as parameters: The name of the SP Partner The Federation Authentication Method The OAM Authentication Scheme name Note: I will discuss in a subsequent article the other parameters of those commands. In the next sections, I will show examples on how to use those methods: For SAML 2.0, I will configure the SP Partner Profile, that will apply all the mappings to SP Partners referencing this profile, unless they override mapping definition For SAML 1.1, I will configure the SP Partner. For OpenID 2.0, I will configure the SP/RP Partner SAML 2.0 Test Setup In this setup, OIF is acting as an IdP and is integrated with a remote SAML 2.0 SP partner identified by AcmeSP. In this test, I will perform Federation SSO with OIF/IdP configured to: Use LDAPScheme as the Authentication Scheme Use BasicScheme as the Authentication Scheme Map BasicSessionScheme to the urn:oasis:names:tc:SAML:2.0:ac:classes:Password Federation Authentication Method Use OAMLDAPPluginAuthnScheme as the Authentication Scheme Map OAMLDAPPluginAuthnScheme to the urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport Federation Authentication Method LDAPScheme as Authentication Scheme Using the OOTB settings regarding user authentication in OAM, the user will be challenged via a FORM based login page based on the LDAPScheme. Also the default Federation Authentication Method mappings configuration maps only the urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport to LDAPScheme (also marked as the default scheme used for authentication), FAAuthScheme, BasicScheme and BasicFAScheme. After authentication via FORM, OIF/IdP would issue an Assertion similar to: <samlp:Response ...> <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer> <samlp:Status> <samlp:StatusCode Value="urn:oasis:names:tc:SAML:2.0:status:Success"/> </samlp:Status> <saml:Assertion ...> <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer> <dsig:Signature> ... </dsig:Signature> <saml:Subject> <saml:NameID ...>[email protected]</saml:NameID> <saml:SubjectConfirmation Method="urn:oasis:names:tc:SAML:2.0:cm:bearer"> <saml:SubjectConfirmationData .../> </saml:SubjectConfirmation> </saml:Subject> <saml:Conditions ...> <saml:AudienceRestriction> <saml:Audience>https://acme.com/sp</saml:Audience> </saml:AudienceRestriction> </saml:Conditions> <saml:AuthnStatement AuthnInstant="2014-03-21T20:53:55Z" SessionIndex="id-6i-Dm0yB-HekG6cejktwcKIFMzYE8Yrmqwfd0azz" SessionNotOnOrAfter="2014-03-21T21:53:55Z"> <saml:AuthnContext> <saml:AuthnContextClassRef> urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport </saml:AuthnContextClassRef> </saml:AuthnContext> </saml:AuthnStatement> </saml:Assertion></samlp:Response> BasicScheme as Authentication Scheme For this test, I will switch the default Authentication Scheme for the SP Partner Profile to BasicScheme instead of LDAPScheme. I will use the OIF WLST setSPPartnerProfileDefaultScheme() command and specify which scheme to be used as the default for the SP Partner Profile referenced by AcmeSP (which is saml20-sp-partner-profile in this case: getFedPartnerProfile("AcmeSP", "sp") ): Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the setSPPartnerProfileDefaultScheme() command:setSPPartnerProfileDefaultScheme("saml20-sp-partner-profile", "BasicScheme") Exit the WLST environment:exit() The user will now be challenged via HTTP Basic Authentication defined in the BasicScheme for AcmeSP. Also, as noted earlier, the default Federation Authentication Method mappings configuration maps only the urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport to LDAPScheme (also marked as the default scheme used for authentication), FAAuthScheme, BasicScheme and BasicFAScheme. After authentication via HTTP Basic Authentication, OIF/IdP would issue an Assertion similar to: <samlp:Response ...> <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer> <samlp:Status> <samlp:StatusCode Value="urn:oasis:names:tc:SAML:2.0:status:Success"/> </samlp:Status> <saml:Assertion ...> <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer> <dsig:Signature> ... </dsig:Signature> <saml:Subject> <saml:NameID ...>[email protected]</saml:NameID> <saml:SubjectConfirmation Method="urn:oasis:names:tc:SAML:2.0:cm:bearer"> <saml:SubjectConfirmationData .../> </saml:SubjectConfirmation> </saml:Subject> <saml:Conditions ...> <saml:AudienceRestriction> <saml:Audience>https://acme.com/sp</saml:Audience> </saml:AudienceRestriction> </saml:Conditions> <saml:AuthnStatement AuthnInstant="2014-03-21T20:53:55Z" SessionIndex="id-6i-Dm0yB-HekG6cejktwcKIFMzYE8Yrmqwfd0azz" SessionNotOnOrAfter="2014-03-21T21:53:55Z"> <saml:AuthnContext> <saml:AuthnContextClassRef> urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport </saml:AuthnContextClassRef> </saml:AuthnContext> </saml:AuthnStatement> </saml:Assertion></samlp:Response> Mapping BasicScheme To change the Federation Authentication Method mapping for the BasicScheme to urn:oasis:names:tc:SAML:2.0:ac:classes:Password instead of urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport for the saml20-sp-partner-profile SAML 2.0 SP Partner Profile (the profile to which my AcmeSP Partner is bound to), I will execute the addSPPartnerProfileAuthnMethod() method: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the addSPPartnerProfileAuthnMethod() command:addSPPartnerProfileAuthnMethod("saml20-sp-partner-profile", "urn:oasis:names:tc:SAML:2.0:ac:classes:Password", "BasicScheme") Exit the WLST environment:exit() After authentication via HTTP Basic Authentication, OIF/IdP would now issue an Assertion similar to (see that the AuthnContextClassRef was changed from PasswordProtectedTransport to Password): <samlp:Response ...> <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer> <samlp:Status> <samlp:StatusCode Value="urn:oasis:names:tc:SAML:2.0:status:Success"/> </samlp:Status> <saml:Assertion ...> <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer> <dsig:Signature> ... </dsig:Signature> <saml:Subject> <saml:NameID ...>[email protected]</saml:NameID> <saml:SubjectConfirmation Method="urn:oasis:names:tc:SAML:2.0:cm:bearer"> <saml:SubjectConfirmationData .../> </saml:SubjectConfirmation> </saml:Subject> <saml:Conditions ...> <saml:AudienceRestriction> <saml:Audience>https://acme.com/sp</saml:Audience> </saml:AudienceRestriction> </saml:Conditions> <saml:AuthnStatement AuthnInstant="2014-03-21T20:53:55Z" SessionIndex="id-6i-Dm0yB-HekG6cejktwcKIFMzYE8Yrmqwfd0azz" SessionNotOnOrAfter="2014-03-21T21:53:55Z"> <saml:AuthnContext> <saml:AuthnContextClassRef> urn:oasis:names:tc:SAML:2.0:ac:classes:Password </saml:AuthnContextClassRef> </saml:AuthnContext> </saml:AuthnStatement> </saml:Assertion></samlp:Response> OAMLDAPPluginAuthnScheme as Authentication Scheme For this test, I will switch the default Authentication Scheme for the SP Partner Profile to OAMLDAPPluginAuthnScheme instead of BasicScheme. I will use the OIF WLST setSPPartnerProfileDefaultScheme() command and specify which scheme to be used as the default for the SP Partner Profile referenced by AcmeSP (which is saml20-sp-partner-profile in this case: getFedPartnerProfile("AcmeSP", "sp") ): Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the setSPPartnerProfileDefaultScheme() command:setSPPartnerProfileDefaultScheme("saml20-sp-partner-profile", "OAMLDAPPluginAuthnScheme") Exit the WLST environment:exit() The user will now be challenged via FORM defined in the OAMLDAPPluginAuthnScheme for AcmeSP. Contrarily to LDAPScheme and BasicScheme, the OAMLDAPPluginAuthnScheme is not mapped by default to any Federation Authentication Methods. As such, OIF/IdP will not be able to find a Federation Authentication Method and will set the method in the SAML Assertion to the OAM Authentication Scheme name. After authentication via FORM, OIF/IdP would issue an Assertion similar to (see the AuthnContextClassRef set to OAMLDAPPluginAuthnScheme): <samlp:Response ...> <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer> <samlp:Status> <samlp:StatusCode Value="urn:oasis:names:tc:SAML:2.0:status:Success"/> </samlp:Status> <saml:Assertion ...> <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer> <dsig:Signature> ... </dsig:Signature> <saml:Subject> <saml:NameID ...>[email protected]</saml:NameID> <saml:SubjectConfirmation Method="urn:oasis:names:tc:SAML:2.0:cm:bearer"> <saml:SubjectConfirmationData .../> </saml:SubjectConfirmation> </saml:Subject> <saml:Conditions ...> <saml:AudienceRestriction> <saml:Audience>https://acme.com/sp</saml:Audience> </saml:AudienceRestriction> </saml:Conditions> <saml:AuthnStatement AuthnInstant="2014-03-21T20:53:55Z" SessionIndex="id-6i-Dm0yB-HekG6cejktwcKIFMzYE8Yrmqwfd0azz" SessionNotOnOrAfter="2014-03-21T21:53:55Z"> <saml:AuthnContext> <saml:AuthnContextClassRef> OAMLDAPPluginAuthnScheme </saml:AuthnContextClassRef> </saml:AuthnContext> </saml:AuthnStatement> </saml:Assertion></samlp:Response> Mapping OAMLDAPPluginAuthnScheme To add the OAMLDAPPluginAuthnScheme to the Federation Authentication Method urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport mapping, I will execute the addSPPartnerProfileAuthnMethod() method: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the addSPPartnerProfileAuthnMethod() command:addSPPartnerProfileAuthnMethod("saml20-sp-partner-profile", "urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport", "OAMLDAPPluginAuthnScheme") Exit the WLST environment:exit() After authentication via FORM, OIF/IdP would now issue an Assertion similar to (see that the method was changed from OAMLDAPPluginAuthnScheme to PasswordProtectedTransport): <samlp:Response ...> <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer> <samlp:Status> <samlp:StatusCode Value="urn:oasis:names:tc:SAML:2.0:status:Success"/> </samlp:Status> <saml:Assertion ...> <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer> <dsig:Signature> ... </dsig:Signature> <saml:Subject> <saml:NameID ...>[email protected]</saml:NameID> <saml:SubjectConfirmation Method="urn:oasis:names:tc:SAML:2.0:cm:bearer"> <saml:SubjectConfirmationData .../> </saml:SubjectConfirmation> </saml:Subject> <saml:Conditions ...> <saml:AudienceRestriction> <saml:Audience>https://acme.com/sp</saml:Audience> </saml:AudienceRestriction> </saml:Conditions> <saml:AuthnStatement AuthnInstant="2014-03-21T20:53:55Z" SessionIndex="id-6i-Dm0yB-HekG6cejktwcKIFMzYE8Yrmqwfd0azz" SessionNotOnOrAfter="2014-03-21T21:53:55Z"> <saml:AuthnContext> <saml:AuthnContextClassRef> urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport </saml:AuthnContextClassRef> </saml:AuthnContext> </saml:AuthnStatement> </saml:Assertion></samlp:Response> SAML 1.1 Test Setup In this setup, OIF is acting as an IdP and is integrated with a remote SAML 1.1 SP partner identified by AcmeSP. In this test, I will perform Federation SSO with OIF/IdP configured to: Use LDAPScheme as the Authentication Scheme Use OAMLDAPPluginAuthnScheme as the Authentication Scheme Map OAMLDAPPluginAuthnScheme to the urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport Federation Authentication Method Use LDAPScheme as the Authentication Scheme Map LDAPScheme to the urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport Federation Authentication Method LDAPScheme as Authentication Scheme Using the OOTB settings regarding user authentication in OAM, the user will be challenged via a FORM based login page based on the LDAPScheme. Also the default Federation Authentication Method mappings configuration maps only the urn:oasis:names:tc:SAML:1.0:am:password to LDAPScheme (also marked as the default scheme used for authentication), FAAuthScheme, BasicScheme and BasicFAScheme. After authentication via FORM, OIF/IdP would issue an Assertion similar to: <samlp:Response ...> <samlp:Status> <samlp:StatusCode Value="samlp:Success"/> </samlp:Status> <saml:Assertion Issuer="https://idp.com/oam/fed" ...> <saml:Conditions ...> <saml:AudienceRestriction> <saml:Audience>https://acme.com/sp/ssov11</saml:Audience> </saml:AudienceRestriction> </saml:Conditions> <saml:AuthnStatement AuthenticationInstant="2014-03-21T20:53:55Z" AuthenticationMethod="urn:oasis:names:tc:SAML:1.0:am:password"> <saml:Subject> <saml:NameIdentifier ...>[email protected]</saml:NameIdentifier> <saml:SubjectConfirmation> <saml:ConfirmationMethod> urn:oasis:names:tc:SAML:1.0:cm:bearer </saml:ConfirmationMethod> </saml:SubjectConfirmation> </saml:Subject> </saml:AuthnStatement> <dsig:Signature> ... </dsig:Signature> </saml:Assertion></samlp:Response> OAMLDAPPluginAuthnScheme as Authentication Scheme For this test, I will switch the default Authentication Scheme for the SP Partner to OAMLDAPPluginAuthnScheme instead of LDAPScheme. I will use the OIF WLST setSPPartnerDefaultScheme() command and specify which scheme to be used as the default for the SP Partner: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the setSPPartnerDefaultScheme() command:setSPPartnerDefaultScheme("AcmeSP", "OAMLDAPPluginAuthnScheme") Exit the WLST environment:exit() The user will be challenged via FORM defined in the OAMLDAPPluginAuthnScheme for AcmeSP. Contrarily to LDAPScheme, the OAMLDAPPluginAuthnScheme is not mapped by default to any Federation Authentication Methods (in the SP Partner Profile). As such, OIF/IdP will not be able to find a Federation Authentication Method and will set the method in the SAML Assertion to the OAM Authentication Scheme name. After authentication via FORM, OIF/IdP would issue an Assertion similar to (see the AuthenticationMethod set to OAMLDAPPluginAuthnScheme): <samlp:Response ...> <samlp:Status> <samlp:StatusCode Value="samlp:Success"/> </samlp:Status> <saml:Assertion Issuer="https://idp.com/oam/fed" ...> <saml:Conditions ...> <saml:AudienceRestriction> <saml:Audience>https://acme.com/sp/ssov11</saml:Audience> </saml:AudienceRestriction> </saml:Conditions> <saml:AuthnStatement AuthenticationInstant="2014-03-21T20:53:55Z" AuthenticationMethod="OAMLDAPPluginAuthnScheme"> <saml:Subject> <saml:NameIdentifier ...>[email protected]</saml:NameIdentifier> <saml:SubjectConfirmation> <saml:ConfirmationMethod> urn:oasis:names:tc:SAML:1.0:cm:bearer </saml:ConfirmationMethod> </saml:SubjectConfirmation> </saml:Subject> </saml:AuthnStatement> <dsig:Signature> ... </dsig:Signature> </saml:Assertion></samlp:Response> Mapping OAMLDAPPluginAuthnScheme To map the OAMLDAPPluginAuthnScheme to the Federation Authentication Method urn:oasis:names:tc:SAML:1.0:am:password for this SP Partner only, I will execute the addSPPartnerAuthnMethod() method: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the addSPPartnerAuthnMethod() command:addSPPartnerAuthnMethod("AcmeSP", "urn:oasis:names:tc:SAML:1.0:am:password", "OAMLDAPPluginAuthnScheme") Exit the WLST environment:exit() After authentication via FORM, OIF/IdP would now issue an Assertion similar to (see that the method was changed from OAMLDAPPluginAuthnScheme to password): <samlp:Response ...> <samlp:Status> <samlp:StatusCode Value="samlp:Success"/> </samlp:Status> <saml:Assertion Issuer="https://idp.com/oam/fed" ...> <saml:Conditions ...> <saml:AudienceRestriction> <saml:Audience>https://acme.com/sp/ssov11</saml:Audience> </saml:AudienceRestriction> </saml:Conditions> <saml:AuthnStatement AuthenticationInstant="2014-03-21T20:53:55Z" AuthenticationMethod="urn:oasis:names:tc:SAML:1.0:am:password"> <saml:Subject> <saml:NameIdentifier ...>[email protected]</saml:NameIdentifier> <saml:SubjectConfirmation> <saml:ConfirmationMethod> urn:oasis:names:tc:SAML:1.0:cm:bearer </saml:ConfirmationMethod> </saml:SubjectConfirmation> </saml:Subject> </saml:AuthnStatement> <dsig:Signature> ... </dsig:Signature> </saml:Assertion></samlp:Response> LDAPScheme as Authentication Scheme I will now show that by defining a Federation Authentication Mapping at the Partner level, this now ignores all mappings defined at the SP Partner Profile level. For this test, I will switch the default Authentication Scheme for this SP Partner back to LDAPScheme, and the Assertion issued by OIF/IdP will not be able to map this LDAPScheme to a Federation Authentication Method anymore, since A Federation Authentication Method mapping is defined at the SP Partner level and thus the mappings defined at the SP Partner Profile are ignored The LDAPScheme is not listed in the mapping at the Partner level I will use the OIF WLST setSPPartnerDefaultScheme() command and specify which scheme to be used as the default for this SP Partner: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the setSPPartnerDefaultScheme() command:setSPPartnerDefaultScheme("AcmeSP", "LDAPScheme") Exit the WLST environment:exit() After authentication via FORM, OIF/IdP would issue an Assertion similar to (see the AuthenticationMethod set to LDAPScheme): <samlp:Response ...> <samlp:Status> <samlp:StatusCode Value="samlp:Success"/> </samlp:Status> <saml:Assertion Issuer="https://idp.com/oam/fed" ...> <saml:Conditions ...> <saml:AudienceRestriction> <saml:Audience>https://acme.com/sp/ssov11</saml:Audience> </saml:AudienceRestriction> </saml:Conditions> <saml:AuthnStatement AuthenticationInstant="2014-03-21T20:53:55Z" AuthenticationMethod="LDAPScheme"> <saml:Subject> <saml:NameIdentifier ...>[email protected]</saml:NameIdentifier> <saml:SubjectConfirmation> <saml:ConfirmationMethod> urn:oasis:names:tc:SAML:1.0:cm:bearer </saml:ConfirmationMethod> </saml:SubjectConfirmation> </saml:Subject> </saml:AuthnStatement> <dsig:Signature> ... </dsig:Signature> </saml:Assertion></samlp:Response> Mapping LDAPScheme at Partner Level To fix this issue, we will need to add the LDAPScheme to the Federation Authentication Method urn:oasis:names:tc:SAML:1.0:am:password mapping for this SP Partner only. I will execute the addSPPartnerAuthnMethod() method: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the addSPPartnerAuthnMethod() command:addSPPartnerAuthnMethod("AcmeSP", "urn:oasis:names:tc:SAML:1.0:am:password", "LDAPScheme") Exit the WLST environment:exit() After authentication via FORM, OIF/IdP would now issue an Assertion similar to (see that the method was changed from LDAPScheme to password): <samlp:Response ...> <samlp:Status> <samlp:StatusCode Value="samlp:Success"/> </samlp:Status> <saml:Assertion Issuer="https://idp.com/oam/fed" ...> <saml:Conditions ...> <saml:AudienceRestriction> <saml:Audience>https://acme.com/sp/ssov11</saml:Audience> </saml:AudienceRestriction> </saml:Conditions> <saml:AuthnStatement AuthenticationInstant="2014-03-21T20:53:55Z" AuthenticationMethod="urn:oasis:names:tc:SAML:1.0:am:password"> <saml:Subject> <saml:NameIdentifier ...>[email protected]</saml:NameIdentifier> <saml:SubjectConfirmation> <saml:ConfirmationMethod> urn:oasis:names:tc:SAML:1.0:cm:bearer </saml:ConfirmationMethod> </saml:SubjectConfirmation> </saml:Subject> </saml:AuthnStatement> <dsig:Signature> ... </dsig:Signature> </saml:Assertion></samlp:Response> OpenID 2.0 In the OpenID 2.0 flows, the RP must request use of PAPE, in order for OIF/IdP/OP to include PAPE information. For OpenID 2.0, the configuration will involve mapping a list of OpenID 2.0 policies to a list of Authentication Schemes. The WLST command will take a list of policies, delimited by the ',' character, instead of SAML 2.0 or SAML 1.1 where a single Federation Authentication Method had to be specified. Test Setup In this setup, OIF is acting as an IdP/OP and is integrated with a remote OpenID 2.0 SP/RP partner identified by AcmeRP. In this test, I will perform Federation SSO with OIF/IdP configured to: Use LDAPScheme as the Authentication Scheme Map LDAPScheme to the http://schemas.openid.net/pape/policies/2007/06/phishing-resistant and http://openid-policies/password-protected policies Federation Authentication Methods (the second one is a custom for this use case) LDAPScheme as Authentication Scheme Using the OOTB settings regarding user authentication in OAM, the user will be challenged via a FORM based login page based on the LDAPScheme. No Federation Authentication Method is defined OOTB for OpenID 2.0, so if the IdP/OP issue an SSO response with a PAPE Response element, it will specify the scheme name instead of Federation Authentication Methods After authentication via FORM, OIF/IdP would issue an SSO Response similar to: https://acme.com/openid?refid=id-9PKVXZmRxAeDYcgLqPm36ClzOMA-&openid.ns=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0&openid.mode=id_res&openid.op_endpoint=https%3A%2F%2Fidp.com%2Fopenid&openid.claimed_id=https%3A%2F%2Fidp.com%2Fopenid%3Fid%3Did-38iCmmlAVEXPsFjnFVKArfn5RIiF75D5doorhEgqqPM%3D&openid.identity=https%3A%2F%2Fidp.com%2Fopenid%3Fid%3Did-38iCmmlAVEXPsFjnFVKArfn5RIiF75D5doorhEgqqPM%3D&openid.return_to=https%3A%2F%2Facme.com%2Fopenid%3Frefid%3Did-9PKVXZmRxAeDYcgLqPm36ClzOMA-&openid.response_nonce=2014-03-24T19%3A20%3A06Zid-YPa2kTNNFftZkgBb460jxJGblk2g--iNwPpDI7M1&openid.assoc_handle=id-6a5S6zhAKaRwQNUnjTKROREdAGSjWodG1el4xyz3&openid.ns.ax=http%3A%2F%2Fopenid.net%2Fsrv%2Fax%2F1.0&openid.ax.mode=fetch_response&openid.ax.type.attr0=http%3A%2F%2Fsession%2Fcount&openid.ax.value.attr0=1&openid.ax.type.attr1=http%3A%2F%2Fopenid.net%2Fschema%2FnamePerson%2Ffriendly&openid.ax.value.attr1=My+name+is+Bobby+Smith&openid.ax.type.attr2=http%3A%2F%2Fschemas.openid.net%2Fax%2Fapi%2Fuser_id&openid.ax.value.attr2=bob&openid.ax.type.attr3=http%3A%2F%2Faxschema.org%2Fcontact%2Femail&openid.ax.value.attr3=bob%40oracle.com&openid.ax.type.attr4=http%3A%2F%2Fsession%2Fipaddress&openid.ax.value.attr4=10.145.120.253&openid.ns.pape=http%3A%2F%2Fspecs.openid.net%2Fextensions%2Fpape%2F1.0&openid.pape.auth_time=2014-03-24T19%3A20%3A05Z&openid.pape.auth_policies=LDAPScheme&openid.signed=op_endpoint%2Cclaimed_id%2Cidentity%2Creturn_to%2Cresponse_nonce%2Cassoc_handle%2Cns.ax%2Cax.mode%2Cax.type.attr0%2Cax.value.attr0%2Cax.type.attr1%2Cax.value.attr1%2Cax.type.attr2%2Cax.value.attr2%2Cax.type.attr3%2Cax.value.attr3%2Cax.type.attr4%2Cax.value.attr4%2Cns.pape%2Cpape.auth_time%2Cpape.auth_policies&openid.sig=mYMgbGYSs22l8e%2FDom9NRPw15u8%3D Mapping LDAPScheme To map the LDAP Scheme to the http://schemas.openid.net/pape/policies/2007/06/phishing-resistant and http://openid-policies/password-protected policies Federation Authentication Methods, I will execute the addSPPartnerAuthnMethod() method (the policies will be comma separated): Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the addSPPartnerAuthnMethod() command:addSPPartnerAuthnMethod("AcmeRP", "http://schemas.openid.net/pape/policies/2007/06/phishing-resistant,http://openid-policies/password-protected", "LDAPScheme") Exit the WLST environment:exit() After authentication via FORM, OIF/IdP would now issue an Assertion similar to (see that the method was changed from LDAPScheme to the two policies): https://acme.com/openid?refid=id-9PKVXZmRxAeDYcgLqPm36ClzOMA-&openid.ns=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0&openid.mode=id_res&openid.op_endpoint=https%3A%2F%2Fidp.com%2Fopenid&openid.claimed_id=https%3A%2F%2Fidp.com%2Fopenid%3Fid%3Did-38iCmmlAVEXPsFjnFVKArfn5RIiF75D5doorhEgqqPM%3D&openid.identity=https%3A%2F%2Fidp.com%2Fopenid%3Fid%3Did-38iCmmlAVEXPsFjnFVKArfn5RIiF75D5doorhEgqqPM%3D&openid.return_to=https%3A%2F%2Facme.com%2Fopenid%3Frefid%3Did-9PKVXZmRxAeDYcgLqPm36ClzOMA-&openid.response_nonce=2014-03-24T19%3A20%3A06Zid-YPa2kTNNFftZkgBb460jxJGblk2g--iNwPpDI7M1&openid.assoc_handle=id-6a5S6zhAKaRwQNUnjTKROREdAGSjWodG1el4xyz3&openid.ns.ax=http%3A%2F%2Fopenid.net%2Fsrv%2Fax%2F1.0&openid.ax.mode=fetch_response&openid.ax.type.attr0=http%3A%2F%2Fsession%2Fcount&openid.ax.value.attr0=1&openid.ax.type.attr1=http%3A%2F%2Fopenid.net%2Fschema%2FnamePerson%2Ffriendly&openid.ax.value.attr1=My+name+is+Bobby+Smith&openid.ax.type.attr2=http%3A%2F%2Fschemas.openid.net%2Fax%2Fapi%2Fuser_id&openid.ax.value.attr2=bob&openid.ax.type.attr3=http%3A%2F%2Faxschema.org%2Fcontact%2Femail&openid.ax.value.attr3=bob%40oracle.com&openid.ax.type.attr4=http%3A%2F%2Fsession%2Fipaddress&openid.ax.value.attr4=10.145.120.253&openid.ns.pape=http%3A%2F%2Fspecs.openid.net%2Fextensions%2Fpape%2F1.0&openid.pape.auth_time=2014-03-24T19%3A20%3A05Z&openid.pape.auth_policies=http%3A%2F%2Fschemas.openid.net%2Fpape%2Fpolicies%2F2007%2F06%2Fphishing-resistant+http%3A%2F%2Fopenid-policies%2Fpassword-protected&openid.signed=op_endpoint%2Cclaimed_id%2Cidentity%2Creturn_to%2Cresponse_nonce%2Cassoc_handle%2Cns.ax%2Cax.mode%2Cax.type.attr0%2Cax.value.attr0%2Cax.type.attr1%2Cax.value.attr1%2Cax.type.attr2%2Cax.value.attr2%2Cax.type.attr3%2Cax.value.attr3%2Cax.type.attr4%2Cax.value.attr4%2Cns.pape%2Cpape.auth_time%2Cpape.auth_policies&openid.sig=mYMgbGYSs22l8e%2FDom9NRPw15u8%3D In the next article, I will cover how OIF/IdP can be configured so that an SP can request a specific Federation Authentication Method to challenge the user during Federation SSO.Cheers,Damien Carru

Read the article

Add Microsoft Core Fonts to Ubuntu

- by Matthew Guay

Have you ever needed the standard Microsoft fonts such as Times New Roman on your Ubuntu computer? Here’s how you can easily add the core Microsoft fonts to Ubuntu. Times New Roman, Arial, and other core Microsoft fonts are still some of the most commonly used fonts in documents and websites. Times New Roman especially is often required for college essays, legal docs, and other critical documents that you may need to write or edit. Ubuntu includes the Liberation alternate fonts that include similar alternates to Times New Roman, Arial, and Courier New, but these may not be accepted by professors and others when a certain font is required. But, don’t worry; it only takes a couple clicks to add these fonts to Ubuntu for free. Installing the Core Microsoft Fonts Microsoft has released their core fonts, including Times New Roman and Arial, for free, and you can easily download these from the Software Center. Open your Applications menu, and select Ubuntu Software Center. In the search box enter the following: ttf-mscorefonts Click Install on the “Installer for Microsoft TrueType core fonts” directly in the search results. Enter your password when requested, and click Authenticate. The fonts will then automatically download and install in a couple minutes depending on your internet connection speed. Once the install is finished, you can launch OpenOffice Writer to try out the new fonts. Here’s a preview of all the fonts included in this pack. And, yes, this does included the infamous Comic Sans and Webdings fonts as well as the all-important Times New Roman. Please Note: By default in Ubuntu, OpenOffice uses Liberation Serif as the default font, but after installing this font pack, the default font will switch to Times New Roman. Adding Other Fonts In addition to the Microsoft Core Fonts, the Ubuntu Software Center has hundreds of free fonts available. Click the Fonts link on the front page to explore these, and install the same as above. If you’ve downloaded another font individually, you can also install it easily in Ubuntu. Just double-click it, and then click Install in the preview window. Conclusion Although you may prefer the fonts that are included with Ubuntu, there are many reasons why having the Microsoft core fonts can be helpful. Thankfully it’s easy in Ubuntu to install them, so you’ll never have to worry about not having them when you need to edit an important document. Similar Articles Productive Geek Tips Enable Smooth fonts on Ubuntu LinuxEmbed True Type Fonts in Word and PowerPoint 2007 DocumentsNew Vista Syntax for Opening Control Panel Items from the Command-lineStupid Geek Tricks: Enable More Fonts for the Windows Command PromptAdding extra Repositories on Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Awe inspiring, inter-galactic theme (Win 7) Case Study – How to Optimize Popular Wordpress Sites Restore Hidden Updates in Windows 7 & Vista Iceland an Insurance Job? Find Downloads and Add-ins for Outlook Recycle !

Read the article

SharePoint.DesignFactory.ContentFiles–building WCM sites

- by svdoever

One of the use cases where we use the SharePoint.DesignFactory.ContentFiles tooling is in building SharePoint Publishing (WCM) solutions for SharePoint 2007, SharePoint 2010 and Office365. Publishing solutions are often solutions that have one instance, the publishing site (possibly with subsites), that in most cases need to go through DTAP. If you dissect a publishing site, in most case you have the following findings: The publishing site spans a site collection The branding of the site is specified in the root site, because: Master pages live in the root site (/_catalogs/masterpage) Page layouts live in the root site (/_catalogs/masterpage) The style library lives in the root site ( /Style Library) and contains images, css, javascript, xslt transformations for your CQWP’s, … Preconfigured web parts live in the root site (/_catalogs/wp) The root site and subsites contains a document library called Pages (or your language-specific version of it) containing publishing pages using the page layouts and master pages The site collection contains content types, fields and lists When using the SharePoint.DesignFactory.ContentFiles tooling it is very easy to create, test, package and deploy the artifacts that can be uploaded to the SharePoint content database. This can be done in a fast and simple way without the need to create and deploy WSP packages. If we look at the above list of artifacts we can use SharePoint.DesignFactory.ContentFiles for master pages, page layouts, the style library, web part configurations, and initial publishing pages (these are normally made through the SharePoint web UI). Some artifacts like content types, fields and lists in the above list can NOT be handled by SharePoint.DesignFactory.ContentFiles, because they can’t be uploaded to the SharePoint content database. The good thing is that these artifacts are the artifacts that don’t change that much in the development of a SharePoint Publishing solution. There are however multiple ways to create these artifacts: Use paper script: create them manually in each of the environments based on documentation Automate the creation of the artifacts using (PowerShell) script Develop a WSP package to create these artifacts I’m not a big fan of the third option (see my blog post Thoughts on building deployable and updatable SharePoint solutions). It is a lot of work to create content types, fields and list definitions using all kind of XML files, and it is not allowed to modify these artifacts when in use. I know… SharePoint 2010 has some content type upgrade possibilities, but I think it is just too cumbersome. The first option has the problem that content types and fields get ID’s, and that these ID’s must be used by the metadata on for example page layouts. No problem for SharePoint.DesignFactory.ContentFiles, because it supports deploy-time resolving of these ID’s using PowerShell. For example consider the following metadata definition for the page layout contactpage-wcm.aspx.properties.ps1: Metadata page layout # This script must return a hashtable @{ name=value; ... } of field name-value pairs # for the content file that this script applies to. # On deployment to SharePoint, these values are written as fields in the corresponding list item (if any) # Note that fields must exist; they can be updated but not created or deleted. # This script is called right after the file is deployed to SharePoint. # You can use the script parameters and arbitrary PowerShell code to interact with SharePoint. # e.g. to calculate properties and values at deployment time. param([string]$SourcePath, [string]$RelativeUrl, $Context) @{ "ContentTypeId" = $Context.GetContentTypeID('GeneralPage'); "MasterPageDescription" = "Cloud Aviator Contact pagelayout (wcm - don't use)"; "PublishingHidden" = "1"; "PublishingAssociatedContentType" = $Context.GetAssociatedContentTypeInfo('GeneralPage') } The PowerShell functions GetContentTypeID and GetAssociatedContentTypeInfo can at deploy-time resolve the required information from the server we are deploying to. I personally prefer the second option: automate creation through PowerShell, because there are PowerShell scripts available to export content types and fields. An example project structure for a typical SharePoint WCM site looks like: Note that this project uses DualLayout. So if you build Publishing sites using SharePoint, checkout out the completely free SharePoint.DesignFactory.ContentFiles tooling and start flying!

Read the article

Installer Reboots at "Detecting hardware" (disks and other hardware) on all recent Server Installs

- by Ryan Rosario

I have a very frustrating problem with my PC. I cannot install any recent version of Ubuntu Server (or even Desktop) since 9.04 even using the text-based installer. I boot from a USB stick created by Unetbootin (I also tried other methods such as startup disk creator with no difference). On the Server installer, it gets to "Detecting Hardware" (the second one about disks and all other hardware, not network hardware) and then either hangs at 0% (waited 24 hours), or reboots after a minute or two. My system (late 2007): ASUS P5NSLI motherboard Intel Core 2 Duo E6600 2.4Ghz 2 x 1GB Corsair 667MHz RAM nVidia GeForce 6600 I have unplugged everything (including the only hard disk, CD-ROMs and floppy). I have only one stick of RAM (tried each one to no avail) and am booting the installer from a USB stick (booting from CD-ROM yields the same problem). I also tried several of the boot options (nomodeset, nousb, acpi=off, noapic, i915.modeset=1/0, xforcevesa) in all combinations) to no avail. The only active parts of my system are the video card, mouse, keyboard and USB stick. I have also updated the BIOS to the most recent version. (FWIW, on the Desktop installer, I get a black screen after hitting the Install option.) Even after removing "quiet" I am unable to see what kernel panic is occurring (or not occurring) to cause the install to crash. I am only able to save the debug logs via a simple webserver in the installer. After the last line (I repeatedly refreshed), the server stops responding and the installer hangs or reboots: Jan 2 01:04:03 main-menu[302]: INFO: Menu item 'disk-detect' selected Jan 2 01:04:04 kernel: [ 309.154372] sata_nv 0000:00:0e.0: version 3.5 Jan 2 01:04:04 kernel: [ 309.154409] sata_nv 0000:00:0e.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.154531] sata_nv 0000:00:0e.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.164442] scsi0 : sata_nv Jan 2 01:04:04 kernel: [ 309.167610] scsi1 : sata_nv Jan 2 01:04:04 kernel: [ 309.167762] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 10 Jan 2 01:04:04 kernel: [ 309.167774] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 10 Jan 2 01:04:04 kernel: [ 309.167948] sata_nv 0000:00:0f.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.168071] sata_nv 0000:00:0f.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.171931] scsi2 : sata_nv Jan 2 01:04:04 kernel: [ 309.173793] scsi3 : sata_nv Jan 2 01:04:04 kernel: [ 309.173943] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 11 Jan 2 01:04:04 kernel: [ 309.173954] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 11 Jan 2 01:04:04 kernel: [ 309.174061] pata_amd 0000:00:0d.0: version 0.4.1 Jan 2 01:04:04 kernel: [ 309.174160] pata_amd 0000:00:0d.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.177045] scsi4 : pata_amd Jan 2 01:04:04 kernel: [ 309.178628] scsi5 : pata_amd Jan 2 01:04:04 kernel: [ 309.178801] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 Jan 2 01:04:04 kernel: [ 309.178811] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface eth0 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface lo Jan 2 01:04:04 kernel: [ 309.485062] ata3: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:04 kernel: [ 309.633094] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Jan 2 01:04:04 kernel: [ 309.641647] ata1.00: ATA-8: ST31000528AS, CC38, max UDMA/133 Jan 2 01:04:04 kernel: [ 309.641658] ata1.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 31/32) Jan 2 01:04:04 kernel: [ 309.657614] ata1.00: configured for UDMA/133 Jan 2 01:04:04 kernel: [ 309.657969] scsi 0:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5 Jan 2 01:04:04 kernel: [ 309.658482] sd 0:0:0:0: Attached scsi generic sg0 type 0 Jan 2 01:04:04 kernel: [ 309.658588] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Jan 2 01:04:04 kernel: [ 309.658812] sd 0:0:0:0: [sda] Write Protect is off Jan 2 01:04:04 kernel: [ 309.658823] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Jan 2 01:04:04 kernel: [ 309.658918] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 2 01:04:04 kernel: [ 309.675630] sda: sda1 sda2 Jan 2 01:04:04 kernel: [ 309.676440] sd 0:0:0:0: [sda] Attached SCSI disk Jan 2 01:04:05 kernel: [ 309.969102] ata2: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:05 kernel: [ 310.281137] ata4: SATA link down (SStatus 0 SControl 300) Anybody have any additional ideas I could try? I am getting ready to just toss the motherboard.

Read the article

Backup and Transfer Foobar2000 to a New Computer

- by Mysticgeek

If you are a fan of Foobar2000 you undoubtedly have tweaked it to the point where you don’t want to set it all up again on a new machine. Here we look at how to transfer Foobar2000 settings to a new Windows 7 machine. Note: For this article we are transferring Foobar2000 settings from on Windows 7 machine to another over a network running Windows Home Server. Foobar2000 Foobar2000 is an awesome music player which is highly customizable and we’ve previously covered. Here we take a look at how it’s set up on the current machine. It’s a nothing flashy, but is set up for our needs and includes a lot of components and playlists. Backup Files Rather than wasting time setting everything up again on a new machine, we can backup the important files and replace them on the new machine. First type or copy the following into the Explorer address bar. %appdata%\foobar2000 Now copy all of the files in the folder and store them on a network drive or some type removable media or device. New Machine Now you can install the latest version of Foobar2000 on your new machine. You can go with a Standard install as we will be replacing our backed up configuration files anyway. When it launches, it will be set with all the defaults…and we want what we had back. Browse to the following on the new machine… %appdata%\foobar2000 Delete all of the files in this directory… Then replace them with the ones we backed up from the other machine. You’ll also want to navigate to C:\Program Files\Foobar2000 and replace the existing Components folder with the backed up one. When you get the screen telling you there is already files of the same name, select Move and Replace, and check the box Do this for the next 6 conflicts. Now we’re back in business! Everything is exactly as it was on the old machine. In this example, we were moving the Foobar2000 files from a computer on the same home network. All the music is coming from a directory on our Windows Home Server so they hadn’t changed. If you’re moving these files to a computer on another machine… say your work computer, you’ll need to adjust where the music folders point to. Windows XP If you’re setting up Foobar2000 on an XP machine, you can enter the following into the Run line. %appdata%\foobar2000 Then copy your backed up files into the Foobar2000 folder, and remember to swap out the Components folder in C:\Program Files\Foobar2000. Confirm to replace the files and folders by clicking Yes to All… Conclusion This method worked perfectly for us on our home network setup. There might be some other things that will need a bit of tweaking, but overall the process is quick and easy. There is a lot of cool things you can do with Foobar2000 like rip an audio CD to FlAC. If you’re a fan of Foobar2000 or considering switching to it, we will be covering more awesome features in future articles. Download Foobar2000 – Windows Only Similar Articles Productive Geek Tips Backup or Transfer Microsoft Office 2007 Quick Parts Between ComputersBackup and Restore Internet Explorer’s Trusted Sites ListSecond Copy 7 [Review]Backup and Restore Firefox Profiles EasilyFoobar2000 is a Fully Customizable Music Player TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 Windows Media Player Glass Icons (icons we like) How to Forecast Weather, without Gadgets Outlook Tools, one stop tweaking for any Outlook version Zoofs, find the most popular tweeted YouTube videos Video preview of new Windows Live Essentials 21 Cursor Packs for XP, Vista & 7

Read the article

Markus Zirn, "Big Data with CEP and SOA" @ SOA, Cloud & Service Technology Symposium 2012

- by JuergenKress

ORACLE PROMOTIONAL DISCOUNT FOR EXCLUSIVE ORACLE DISCOUNT, ENTER PROMO CODE: DJMXZ370 Early-Bird Registration is Now Open with Special Pricing! Register before July 1, 2012 to qualify for discounts. Visit the Registration page for details. The International SOA, Cloud + Service Technology Symposium is a yearly event that features the top experts and authors from around the world, providing a series of keynotes, talks, demonstrations, and panels, as well as training and certification workshops - all dedicated to empowering IT professionals to realize modern service technologies and practices in the real world. Click here for a two-page printable conference overview (PDF). Big Data with CEP and SOA - September 25, 2012 - 14:15 Speaker: Markus Zirn, Oracle and Baz Kuthi, Avocent The "Big Data" trend is driving new kinds of IT projects that process machine-generated data. Such projects store and mine using Hadoop/ Map Reduce, but they also analyze streaming data via event-driven patterns, which can be called "Fast Data" complementary to "Big Data". This session highlights how "Big Data" and "Fast Data" design patterns can be combined with SOA design principles into modern, event-driven architectures. We will describe specific architectures that combines CEP, Distributed Caching, Event-driven Network, SOA Composites, Application Development Framework, as well as Hadoop. Architecture patterns include pre-processing and filtering event streams as close as possible to the event source, in memory master data for event pattern matching, event-driven user interfaces as well as distributed event processing. Focus is on how "Fast Data" requirements are elegantly integrated into a traditional SOA architecture. Markus Zirn is Vice President of Product Management covering Oracle SOA Suite, SOA Governance, Application Integration Architecture, BPM, BPM Solutions, Complex Event Processing and UPK, an end user learning solution. He is the author of “The BPEL Cookbook” (rated best book on Services Oriented Architecture in 2007) as well as “Fusion Middleware Patterns”. Previously, he was a management consultant with Booz Allen & Hamilton’s High Tech practice in Duesseldorf as well as San Francisco and Vice President of Product Marketing at QUIQ. Mr. Zirn holds a Masters of Electrical Engineering from the University of Karlsruhe and is an alumnus of the Tripartite program, a joint European degree from the University of Karlsruhe, Germany, the University of Southampton, UK, and ESIEE, France. KEYNOTES & SPEAKERS More than 80 international subject matter experts will be speaking at the Symposium. Below are confirmed keynotes and speakers so far. Over 50% of the agenda has not yet been finalized. Many more speakers to come. View the partial program calendars on the Conference Agenda page. CONFERENCE THEMES & TRACKS Cloud Computing Architecture & Patterns New SOA & Service-Orientation Practices & Models Emerging Service Technology Innovation Service Modeling & Analysis Techniques Service Infrastructure & Virtualization Cloud-based Enterprise Architecture Business Planning for Cloud Computing Projects Real World Case Studies Semantic Web Technologies (with & without the Cloud) Governance Frameworks for SOA and/or Cloud Computing Projects Service Engineering & Service Programming Techniques Interactive Services & the Human Factor New REST & Web Services Tools & Techniques Oracle Specialized SOA & BPM Partners Oracle Specialized partners have proven their skills by certifications and customer references. To find a local Specialized partner please visit http://solutions.oracle.com SOA & BPM Partner Community For regular information on Oracle SOA Suite become a member in the SOA & BPM Partner Community for registration please visit www.oracle.com/goto/emea/soa (OPN account required) If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Mix Forum Technorati Tags: Markus Zirn,SOA Symposium,Thomas Erl,SOA Community,Oracle SOA,Oracle BPM,BPM Community,OPN,Jürgen Kress

Read the article

Integrate Google Docs with Outlook the Easy Way

- by Matthew Guay

Want to use Google Docs and Microsoft office together? Here’s how you can use Harmony for Google Docs to integrates them seamlessly with Outlook. Harmony for Google Docs is an exciting new plugin for Outlook 2007 (a version for Outlook 2010 is in the works). It lets you integrate your Google Docs account with Outlook via a sidebar. From this, you can find any of your Google docs or upload a new document, and then you can open the document to view or edit it in Outlook. Getting Started Download Harmony for Google Docs (link below), and install as normal. Make sure Outlook is closed before you run the install. Next time you open Outlook, the new Harmony sidebar will automatically open. Enter your Google Account info, and click Sign In. Now, all of your Google Docs will show up in the sidebar. Double-click any file to open it in Outlook. You may have to sign-in to Google Docs the first time you open a document. Here’s a Google Doc open in Outlook. Notice that everything works, including full editing. All Google Docs features worked great in our tests except for the new drawings tool. When we tried to insert a drawing, Outlook had a script error. This was the only problem we had with Harmony, and could be due to an interaction between Google Drawings and Outlook’s rendering engine. Harmony makes it easy to find any file in your Google Docs account. You can search for a file, or sort your files by type, recentness, and more. You can also easily add any document to Google Docs directly from Harmony. You can drag and drop any document, including one attached to an email, to the Harmony sidebar, and it will directly upload to your Google Docs account. And, when you’re writing a new email or reply, click the Show Documents button to open the Harmony sidebar. From here, you can add documents as usual and share it with email recipient. Conclusion We previously covered a similar app OffiSync which combines Google doc features with MS Office. However, Harmony makes it much easier to use Google Apps along with Outlook. This gives you an easy and efficient way to collaborate on documents with coworkers, all without leaving Outlook. And, if your company uses SharePoint instead of Google Docs, Harmony offers a SharePoint edition that integrates with Outlook just as easily! Link Download Harmony for Google Docs Similar Articles Productive Geek Tips How To Export Documents from Google Docs to Your ComputerView Your Google Calendar in Outlook 2007Sync Your Outlook and Google Calendar with Google Calendar SyncIntegrate Twitter With Microsoft OutlookSlacker Geek: Update Your Facebook Profile from Outlook TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Find That Elusive Icon with FindIcons Looking for Good Windows Media Player 12 Plug-ins? Find Out the Celebrity You Resemble With FaceDouble Whoa ! Use Printflush to Solve Printing Problems Icelandic Volcano Webcams

Read the article

HTML Presence Controls for Communications Server 14 CodePlex Project

Showing Presence on the Web If youre running Office Communicator Server 2007 R2, you know that your only out-of-the-box option for showing presence on the web is to use the NameControl ActiveX control that ships as part of Office. Being an ActiveX control, this obviously means that youre limited to Internet Explorer. Also, nobody likes ActiveX controls What if you want to show the presence of users in a pure ASP.NET or HTML application and cant assume that the user has Communicator installed you need anASP.NET or HTML presence control. HTML Presence Controls for Microsoft Communications Server 14 We recently worked with the UC team at Microsoft on a keynote demo for TechEd 2010 in New Orleans. The demo was for a fictitious airline Fabrikam Airlines that wanted to show the presence of customer service and reservations agents on its website. Customers could also start an instant message conversation with the agents using a Silverlight web chat window that used WCF to communicate with the backend UCMA application. We built HTML Presence Controls that use AJAX to poll a REST-based WCF service running in IIS and hosting a UCMA 3.0 presence subscription application. Microsoft has graciously allowed us to publish these on CodePlex so that the development community can benefit from them: http://htmlpresencecontrols.codeplex.com/ We will be maintaining the CodePlex project as new builds of UCMA 3.0 become available. Check out the project home page on CodePlex for some more in-depth details on how the controls are implemented. ASP.NET Server Control Implementation Were providing an ASP.NET Server Control implementation that you can use stand-alone or in a GridView or Repeater (or other layout control). The control has properties that allow you to control its appearance, e.g. you can choose whether or not to show the contacts name or availability text. You can also use the server control in a layout control such as a GridView by putting it in a TemplateColumn and binding to the Sip Uri in the data source. Disclaimer Once we started working on these, we realized why Microsoft hasnt shipped such controls as part of the product. There are some tradeoffs you have to be aware of when using these controls, heres the high level. Privacy The backend UCMA 3.0 application that subscribes to presence of contacts runs as a trusted application and can thus retrieve the presence of any user in the organization. Theres currently no good way in UCMA to apply any privacy rules to ensure that the consumer of the presence controls has permission to see the presence of the contacts that the controls are bound to. Just to be absolutely crystal clear These controls provide a way to query the presence of any user in the organization, regardless of the privacy relationship between the person consuming the controls and the contacts whose presence is being displayed. Were exploring options for a design pattern that would allow you to inject some privacy controls. Keep in mind though that you would most likely be responsible for implementing this logic, as there is currently no functionality in UCMA that allows you to do that. Polling the WCF REST Service The controls poll the backend WCF service to retrieve the presence of contacts - you can control the refresh interval so that they poll less often. We implemented a caching layer so that the WCF service is always communicating with a presence cache it never communicates directly with Communications Server. For example, if your web page is showing the presence of sip:[email protected] and 500 people have the page open, the presence cache only contains one instance of the subscription Communications Server is not being polled 500 times for the presence of that contact. Once the presence of a contact changes, it is updated in the cache. There are some server-based push mechanisms that would work nicely here, such as the one that Outlook Web Access 2010 uses. Unfortunately we didnt have time to explore these options. Community Contribution Take a look at the project Issue Tracker, there are a couple of things we can use some help with. Shoot me a note if youre interested in contributing to the project. Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

Read the article

Beginner Geek: Scan a Document or Picture in Windows 7

- by Mysticgeek

There may come a time when you want to digitize your priceless old pictures, or need to scan a receipts and documents for your company. Today we look at how to scan a picture or document in Windows 7. Scanning Your Document In this example we’re using an HP PSC 1500 All-In-One printer connected to a Windows 7 Home Premium 32-bit system. Different scanners will vary, however the process is essentially the same. The scanning process has changed a bit since the XP days. To scan a document in Windows 7, place the document or picture in the scanner, click on Start, and go to Devices and Printers. When the Devices and Printers window opens, find your scanning device and double-click on it to get the manufacturers Printer Actions menu. For our HP PSC 1500 we have a few different options like printing, device setup, and scanner actions. Here we’ll click on the Scan a document or photo hyperlink. The New Scan window opens and from here you can adjust the quality of the scanned image and choose the output file type. Then click the Preview button to get an idea of what the image will look like. If you’re not happy with the preview, then you can go back and make any adjustments to the quality of the document or photo. Once everything looks good, click on the Scan button. The scanning process will start. The amount of time it takes will depend on your scanner type, and the quality of the settings you choose. The higher the quality…the more time it will take. You will have the option to tag the picture if you want to… Now you can view your scanned document or photo inside Windows Photo Viewer. If you’re happy with the look of the document, you can send it off in an email, put it on an network drive, FTP it… whatever you need to do with it. Another method is to place the document of photo you wish to scan in the scanner, open up Devices and Printers, then right-click on the scanning device and select Start Scan from the context menu. This should bypass the manufacturer screen and go directly into the New Scan window, where you can start the scan process. From the Context Menu you can also choose Scan Properties. This will allow you to test the scanner if you’re having problems with it and change some of its settings. Or you can choose Scan Profiles which allows you to use pre-selected settings, create your own, or set one as the default. Although scanning documents and photos isn’t a common occurrence as it was a few years ago, Windows 7 still includes the feature. When you need to scan a document or photo in Windows 7, this should get you started. Similar Articles Productive Geek Tips Easily Rotate Pictures In Word 2007Beginner Geek: Delete User Accounts in Windows 7Customize Your Welcome Picture Choices in Windows VistaSecure Computing: Detect and Eliminate Malware Using Windows DefenderMark Your Document As Final in Word 2007 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips VMware Workstation 7 Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Creating a Password Reset Disk in Windows Bypass Waiting Time On Customer Service Calls With Lucyphone MELTUP – "The Beginning Of US Currency Crisis And Hyperinflation" Enable or Disable the Task Manager Using TaskMgrED Explorer++ is a Worthy Windows Explorer Alternative Error Goblin Explains Windows Error Codes

Read the article

SharePoint 2010 Hosting :: SharePoint 2010 Custom Web Template

- by mbridge

SharePoint 2010 offers some changes and additions to the SharePoint 2007 approach. Site definitions and publishing providers remain largely the same, but site templates created from the SharePoint UI or SharePoint Designer are now saved to a .WSP file, the same solution deployment packaging file format used for deploying custom SharePoint solutions. Site Templates saved to a .WSP solution file can be imported into Visual Studio for additional customization. Introducing the WebTemplate Feature Element The WebTemplate element, introduced in SharePoint 2010, allows site templates to be defined and deployed as a Feature as part of a solution package. A WebTemplate element feature can be used to deploy site templates in either a Farm or Sandbox solution - without modification. If deployed as a Farm feature and solution, site templates will appear in the site collection provisioning page in Central Administration and can be used to provision new site collections, or within a Site Collection to create sub-sites. If deployed as a Site feature and Sandbox solution, site templates will appear within the site collection to support creating a root site or sub-sites. Creating a new WebTemplate Feature in Visual Studio 2010 In addition to supporting the ability to save and import Site Templates created from the SharePoint UI into Visual Studio for customization, it can also be used to create new site templates from scratch. In the following sample we will walk through how to create a new WebTemplate solution based on a customized version of the out-of-box Blank Site. 1. Create a new Empty SharePoint Project in Visual Studio 2010. 2. Add a new Empty Element to the project. we like to create folders for each type of element in our solution, so in our sample, we have created a Web Templates folder, and then added the BLANKENT element. NOTE: The Elements folder MUST share the same name as the WebTemplate name property. 3. Open the empty Elements.xml and add the <WebTemplate /> element block. 4. Copy the default.aspx and ONET.XML files from the STS site definition location at 14\TEMPLATES\Site Templates\STS. We will customize the ONET.XML in the next section. Open the properties for each file and set the Deployment Type to ElementFile. This ensures the files are deployed with the Element when included in a Feature. 5. By default a new feature is added to the solution for you automatically when a new element is added to the solution. Rename and edit the feature as appropriate. Select Farm for the scope to deploy the WebTemplate to the entire farm, or Site for a sandboxed solution. Customize the ONET.XML At this point, you have a working WebTemplate solution that will deploy the identical site to the out-of-box Blank Site, however the ONET.XML supporting the STS site definition contains 3 configurations – essentially 3 separate site templates and can be simplified before customizing. In the following sample, we have trimmed the ONET.XML to the essentials for a single Site Template, and added references to the <SiteFeatures /> and <WebFeatures /> elements to include the SharePoint Standard and Enterprise features. We have left the top-level navigation bar, and the default page module intact, but removed all other extraneous markup.

Read the article

Make Your Mouse Pointers Left-hand Friendly

- by Matthew Guay

It’s a right-centric world, with everything from pencils to computer mice expecting you to be right-handed. Here’s how you can train your mouse and cursors in Windows 7 and Vista to respect your left-handedness. Using your Left Hand the Right Way It’s easy to switch your mouse to left-handed mode. Enter “mouse” in your Start menu search, and select the first entry. Check the “Switch primary and secondary buttons” box to make your mouse more left-hand friendly. Now your primary select button is your right button, and the secondary button (commonly referred to as right-click) is the left button. But, it can still be awkward to select items on screen with your left hand using the default cursors. MSDN has a free set of cursors designed for left-handed users, that can fix this problem for you. These cursors are exactly like the default Aero cursors in Windows 7 and Vista, except they are reversed to make them better for left-handed use. The cursors are available in 3 sizes: normal, large, and extra large. The normal ones are the same size as the default ones in Windows 7; feel free to choose the other sizes if you prefer them. Click each link to download all 6 cursors for your size (link below). Click “I Agree” after selecting the cursors to accept the license agreement and download them. Once you have all 6 cursors downloaded, select the Pointers tab in the Mouse Properties dialog. Click the cursor to change, and then click Browse to select the new cursor. Browse to the folder you downloaded your new cursors to, select the correct cursor, and click Open. Do this for each of the 6 cursors to be changed. Strangely, the Busy cursor (the spinning blue orb) is a static cursor, so you may not wish to change it. All the other ones look and act like their standard counterparts. Here’s the cursors to be changed, and their equivalents in the default cursors: Normal Select: aero_arrow_left.cur Help Select: aero_helpsel_left.cur Working in Background: aero_working_left.ani Busy: aero_busy_left.cur Handwriting: aero_pen_left.cur Link Select: aero_link_left.cur After changing all the cursors, click Save As… to save this mouse scheme so you can easily select it in the future. Finally click Ok to close the Mouse Properties dialog and accept the changes. Now your pointers will be easier to use left-handed! Conclusion Whether you’re right-handed or left-handed, you can enjoy the Aero cursors in Windows 7 or Vista in the way that works best for you. Unfortunately, many mice are still designed for right-handed people, but this trick will help you make the best out of your mouse. We included all of the 6 cursors for you in a zip file you can download Here. This will make it easier for you to get them all together without having to download them individually. Link Download Left-Handed Mouse Pointers from MSDN Similar Articles Productive Geek Tips Prevent Themes From Modifying Icons and Cursors in Windows 7How To Personalize Windows 7 StarterShow Two Time Zones in Your Outlook 2007 CalendarMake Mouse Navigation Faster in WindowsWhy Doesn’t Tab Work for Drop-down Controls in Firefox on OS X? TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Microsoft’s “How Do I ?” Videos Home Networks – How do they look like & the problems they cause Check Your IMAP Mail Offline In Thunderbird Follow Finder Finds You Twitter Users To Follow Combine MP3 Files Easily QuicklyCode Provides Cheatsheets & Other Programming Stuff

Read the article

Preview Before You Paste with Live Preview in Office 2010

- by DigitalGeekery

Do you often find yourself frustrated that content you just copied and pasted didn’t turn out the way you expected? With the new Live Preview in Office 2010, you can preview how copied content will look when it’s pasted even between Office applications. Not every paste preview option will be available in every circumstance. The available options will be based on the applications being used and what content is copied. Copy your content like normal by right-clicking and selecting Copy, pressing Crtl + C, or selecting Copy from the Home tab. Next, select your location to paste the content. Now you can access the Paste Preview buttons either by selecting the Paste dropdown list from the Home tab… …Or by right-clicking. As you hover your cursor over each of the Paste Options buttons, you will see a preview of what it will look like if you paste using that option. Click the corresponding button when you find the paste option you like. The “Paste” will paste all the content and formatting as you can see below. Values will paste values only, no formatting. Formatting will paste only the formatting, no values. Hover over Paste Special to reveal any additional paste options. The process is similar in other Office applications. As you can see in the Word document below, Keep Text Only will paste the text, but not the orange color format from the original text. Even after you’ve pasted, there is still time to change your mind. After you paste content you’ll see a Paste Option button near your content. If you don’t, you can pull it up by pressing the Ctrl key. Note: This is also available after using Ctrl + V to paste. Click to enable the dropdown and select one of the available options. Using Live Paste Preview between multiple applications is just as easy. If we preview pasting the content from our Word document into PowerPoint by using the Keep Source Formatting option, we’ll see that the outcome looks awful. Selecting the Use Destination Theme will merge the text into the theme of the PowerPoint document and looks a lot better on our slide. Live Paste Preview is a nice addition to Office 2010 and is sure to save time spent undoing the unexpected consequences of pasting content. Looking for more Office 2010 tips? Check out some of our other Office 2010 posts like how to create a customized tab on the Office 2010 ribbon, and how to use the streamlined printing features in Office 2010. Similar Articles Productive Geek Tips Edit Microsoft Word 2007 Documents in Print PreviewPreview Documents Without Opening Them In Word 2007How to See Where a TinyUrl Is Really Linking ToHow To Upload Office 2010 Documents to Web Apps Technical PreviewPreview Links and Images in Google Chrome TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows Check these Awesome Chrome Add-ons iFixit Offers Gadget Repair Manuals Online Vista style sidebar for Windows 7 Create Nice Charts With These Web Based Tools Track Daily Goals With 42Goals Video Toolbox is a Superb Online Video Editor

Read the article

Make Text and Images Easier to Read with the Windows 7 Magnifier

- by DigitalGeekery

Do you have impaired vision or find it difficult to read small print on your computer screen? Today, we’ll take a closer look at how to magnify that hard to read content with the Magnifier in Windows 7. Magnifier was available in previous versions of Windows, but the Windows 7 version comes with some notable improvements. There are now three screen modes in Magnifier. Full Screen and Lens mode, however, require Windows Aero to be enabled. If your computer doesn’t support Aero, or if you’re not using am Aero theme, Magnifier will only work in Docked mode. Using Magnifier in Windows 7 You can find the Magnifier by going to Start > All Programs > Accessories > Ease of Access > Magnifier. Alternately, you can type magnifier into the Search box in the Start Menu and hit Enter. On the Magnifier toolbar, choose your View mode by clicking Views and choosing from the available options. Clicking the plus (+) and minus (-) buttons will zoom in or zoom out. You can change the zoom in/out percentage by adjusting the slider bar. You can also enable color inversion and select tracking options. Click OK when finished to save your settings. After a brief period, the Magnifier Toolbar will switch to a magnifying glass icon. Simply click the magnifying glass to display the Magnifier Toolbar again. Docked Mode In Docked mode, a portion of the screen is magnified and docked at the top of the screen. The rest of your desktop will remain in it’s normal state. You can then control which area of the screen is magnified by moving your mouse. Full Screen Mode This magnifies your entire screen and follows your mouse as you move it around. If you loose track of where you are on the screen, use the Ctrl + Alt + Spacebar shortcut to preview where your mouse pointer is on the screen. Lens Mode The Lens screen mode is similar to holding a magnifying glass up to your screen. Full screen mode magnifies the area around the mouse. The magnified area moves around the screen with your mouse. Shortcut Keys Windows key + (+) to zoom in Windows key + (-) to zoom out Windows key + ESC to exit Ctrl + Alt + F – Full screen mode Ctrl + Alt + L – Lens mode Ctrl + Alt + D – Dock mode Ctrl + Alt + R – Resize the lens Ctrl + Alt + Spacebar – Preview full screen Conclusion Windows Magnifier is a nice little tool if you have impaired vision or just need to make items on the screen easier to read. Similar Articles Productive Geek Tips New Features in WordPad and Paint in Windows 7How-To Geek on Lifehacker: How to Make Windows Vista Less AnnoyingUsing Comments in Word 2007 DocumentsMake Your PC Look Like Windows Phone 7Use Image Placeholders to Display Documents Faster in Word TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Windows Media Player Plus! – Cool WMP Enhancer Get Your Team’s World Cup Schedule In Google Calendar Backup Drivers With Driver Magician TubeSort: YouTube Playlist Organizer XPS file format & XPS Viewer Explained Microsoft Office Web Apps Guide

Search Results

Search found 4230 results on 170 pages for 'virtualpc 2007'.

Page 143/170 | < Previous Page | 139 140 141 142 143 144 145 146 147 148 149 150 | Next Page >

- by chum of chance

- by Lilienthal

- by user1509541

- by Nic

- by Dyppl

- by ThatMacLad

- by J M 4

- by Manesh Karunakaran

- by SABROG

- by Stephan

- by pinaldave

- by Jason Fitzpatrick

- by Damien Carru

- by Matthew Guay

- by svdoever

- by Ryan Rosario

- by Mysticgeek

- by JuergenKress

- by Matthew Guay

- by Mysticgeek

- by mbridge

- by Matthew Guay

- by DigitalGeekery

- by DigitalGeekery

< Previous Page | 139 140 141 142 143 144 145 146 147 148 149 150 | Next Page >