Search Results

Search found 23301 results on 933 pages for 'check in policy'.

Page 144/933 | < Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >

  • setup Zyxel USG 20W as L2TP VPN Server

    - by Massimo
    I've a Zywall USG 20W (wireless disabled) behind a router supplied by the ISP. All ports (both TCP and UDP) on the ISP router are forwarded to the 20W. I'm trying to configure an L2TP VPN to be used by Windows Xp / 7 with Microsoft native client. This was working before with a different firewall, so I'm pretty sure that all the required packets are flowing to the 20W. I followed a tutorial from the italian Zyxel Website, but I cannot get the VPN to work. Always cannot pass phase 2, and I see the following on the log: [ID]: Tunnel [Default_L2TP_VPN_Connection] Phase 2 local policy mismatch Phase 1 goes fine. In Windows the error is always 788. This happens regardless the proposals I set in the phase 1 and 2 setting. What should I check ? Is there any way to get more detailed diagnostic info (policy mismatch is too generic) ? Thanks a lot to whom may help. Massimo.

    Read the article

  • Cisco PIX 8.0.4, static address mapping not working?

    - by Bill
    upgrading a working Pix running 5.3.1 to 8.0.4. The memory/IOS upgrade went fine, but the 8.0.4 configuration is not quite working 100%. The 5.3.1 config on which it was based is working fine. Basically, I have three networks (inside, outside, dmz) with some addresses on the dmz statically mapped to outside addresses. The problem seems to be that those addresses can't send or receive traffic from the outside (Internet.) Stuff on the DMZ that does not have a static mapping seems to work fine. So, basically: Inside - outside: works Inside - DMZ: works DMZ - inside: works, where the rules allow it DMZ (non-static) - outside: works But: DMZ (static) - outside: fails Outside - DMZ: fails (So, say, udp 1194 traffic to .102, http to .104) I suspect there's something I'm missing with the nat/global section of the config, but can't for the life of me figure out what. Help, anyone? The complete configuration is below. Thanks for any thoughts! ! PIX Version 8.0(4) ! hostname firewall domain-name asasdkpaskdspakdpoak.com enable password xxxxxxxx encrypted passwd xxxxxxxx encrypted names ! interface Ethernet0 nameif outside security-level 0 ip address XX.XX.XX.100 255.255.255.224 ! interface Ethernet1 nameif inside security-level 100 ip address 192.168.68.1 255.255.255.0 ! interface Ethernet2 nameif dmz security-level 10 ip address 192.168.69.1 255.255.255.0 ! boot system flash:/image.bin ftp mode passive dns server-group DefaultDNS domain-name asasdkpaskdspakdpoak.com access-list acl_out extended permit udp any host XX.XX.XX.102 eq 1194 access-list acl_out extended permit tcp any host XX.XX.XX.104 eq www access-list acl_dmz extended permit tcp host 192.168.69.10 host 192.168.68.17 eq ssh access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 192.168.68.0 255.255.255.0 eq ssh access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 192.168.68.0 255.255.255.0 eq 5901 access-list acl_dmz extended permit udp host 192.168.69.103 any eq ntp access-list acl_dmz extended permit udp host 192.168.69.103 any eq domain access-list acl_dmz extended permit tcp host 192.168.69.103 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.100 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.101 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.101 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.104 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.104 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.69.104 eq 8080 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.69.104 eq 8099 access-list acl_dmz extended permit tcp host 192.168.69.105 any eq www access-list acl_dmz extended permit tcp host 192.168.69.103 any eq smtp access-list acl_dmz extended permit tcp host 192.168.69.105 host 192.168.68.103 eq ssh access-list acl_dmz extended permit tcp host 192.168.69.104 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 any eq https pager lines 24 mtu outside 1500 mtu inside 1500 mtu dmz 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 static (dmz,outside) XX.XX.XX.103 192.168.69.11 netmask 255.255.255.255 static (inside,dmz) 192.168.68.17 192.168.68.17 netmask 255.255.255.255 static (inside,dmz) 192.168.68.100 192.168.68.100 netmask 255.255.255.255 static (inside,dmz) 192.168.68.101 192.168.68.101 netmask 255.255.255.255 static (inside,dmz) 192.168.68.102 192.168.68.102 netmask 255.255.255.255 static (inside,dmz) 192.168.68.103 192.168.68.103 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.104 192.168.69.100 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.105 192.168.69.105 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.102 192.168.69.10 netmask 255.255.255.255 access-group acl_out in interface outside access-group acl_dmz in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.97 1 route dmz 10.71.83.0 255.255.255.0 192.168.69.10 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet 192.168.68.17 255.255.255.255 inside telnet timeout 5 ssh timeout 5 console timeout 0 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! service-policy global_policy global prompt hostname context Cryptochecksum:2d1bb2dee2d7a3e45db63a489102d7de

    Read the article

  • Configuring Fortigate OS4 for FTPS

    - by Paul
    I configured iis7 ftp to allow ssl connections. I set the ssl firewall to use ports 50000-50050. If I set up a custom service on my fortigate firewall for ftps with source ports 990-50050 and destination ports 990-50050, set it to a firewall policy and connect from a client it connects and works successfully. If I create a service FTPS Control with source port 990 and destination port 990 and another service,FTP Data with source ports 50000-50050 and destination ports 50000-50050 add them to a group FTPSSL, replace the ftps policy with FTPSSL and try connecting it tries to connect to port 990 and eventually times out. Is there a way to configure the service to only use the ports I need and not every port from 990 up?

    Read the article

  • rpm build from src file

    - by danielrutledge
    Hi all, I'm trying to build from a *.src.rpm file on FC 12 in such a way that the files are distributed a across my system as they would with a normal binary build (in this case, *.h files end up in /usr/include). When I ran rpmbuild, the headers weren't present. Here's my rpmbuild command: [root@localhost sphirewalld]# rpm -ivv /home/dan/Downloads/gtest-1.3.0-2.20090601svn257.fc12.src.rpm ============== /home/dan/Downloads/gtest-1.3.0-2.20090601svn257.fc12.src.rpm Expected size: 489395 = lead(96)+sigs(180)+pad(4)+data(489115) Actual size: 489395 loading keyring from pubkeys in /var/lib/rpm/pubkeys/*.key couldn't find any keys in /var/lib/rpm/pubkeys/*.key loading keyring from rpmdb opening db environment /var/lib/rpm/Packages cdb:mpool:joinenv opening db index /var/lib/rpm/Packages rdonly mode=0x0 locked db index /var/lib/rpm/Packages opening db index /var/lib/rpm/Name rdonly mode=0x0 read h# 931 Header sanity check: OK added key gpg-pubkey-57bbccba-4a6f97af to keyring read h# 1327 Header sanity check: OK added key gpg-pubkey-7fac5991-4615767f to keyring read h# 1420 Header sanity check: OK added key gpg-pubkey-16ca1a56-4a100959 to keyring read h# 1896 Header sanity check: OK added key gpg-pubkey-a3a882c1-4a1009ef to keyring Using legacy gpg-pubkey(s) from rpmdb /home/dan/Downloads/gtest-1.3.0-2.20090601svn257.fc12.src.rpm: Header SHA1 digest: OK (3e98ed9b1631395d417e00f35c83ebe588ea9d3b) added source package [0] found 1 source and 0 binary packages Expected size: 489395 = lead(96)+sigs(180)+pad(4)+data(489115) Actual size: 489395 InstallSourcePackage at: psm.c:232: Header SHA1 digest: OK (3e98ed9b1631395d417e00f35c83ebe588ea9d3b) gtest-1.3.0-2.20090601svn257.fc12 ========== Directories not explicitly included in package: 0 /root/rpmbuild/SOURCES/ 1 /root/rpmbuild/SPECS/ ========== warning: user mockbuild does not exist - using root warning: group mockbuild does not exist - using root fini 100664 1 ( 0, 0) 478034 /root/rpmbuild/SOURCES/gtest-1.3.0.tar.bz2;4ba93ce1 unknown warning: user mockbuild does not exist - using root warning: group mockbuild does not exist - using root fini 100644 1 ( 0, 0) 30505 /root/rpmbuild/SOURCES/gtest-svnr257.patch;4ba93ce1 unknown warning: user mockbuild does not exist - using root warning: group mockbuild does not exist - using root fini 100644 1 ( 0, 0) 2732 /root/rpmbuild/SPECS/gtest.spec;4ba93ce1 unknown GZDIO: 63 reads, 511788 total bytes in 0.005930 secs closed db index /var/lib/rpm/Name closed db index /var/lib/rpm/Packages closed db environment /var/lib/rpm/Packages Thanks for your help.

    Read the article

  • Connecting a limited user to win server 2003 through LogMeIn

    - by Jeff
    Logmein support can't help me, maybe someone here can. I have a user on a windows 2003 server (non administrator). When I first created him and tried to connect through remote desktop I got the error "The local policy of the system does not permit you to logon interactively." I looked up the error and saw that this user was not a member of the Remote Desktop Users group. I added him to the group and was able to remote desktop in just fine. Then I tried to connect this user to the server through LogMeIn (pro trial version). I got the same error as when the user was not a part of the Remote Desktop Users group ("The local policy of the system does not permit you to logon interactively."). Can anyone tell me any other groups the user must be a member of in order to be allowed access through LogMeIn? I would image this is a common requirement logmein support seemed to have no idea.

    Read the article

  • VirtualBox guest responds to ping but all ports closed in nmap

    - by jeremyjjbrown
    I want to setup a test database on a vm for development purposes but I cannot connect to the server via the network. I've got Ubuntu 12.04vm installed on 12.04 host in Virtualbox 4.2.4 set to - Bridged network mode - Promiscuous Allow All When I try to ping the virtual guest from any network client I get the expected result. PING 192.168.1.209 (192.168.1.209) 56(84) bytes of data. 64 bytes from 192.168.1.209: icmp_req=1 ttl=64 time=0.427 ms ... Internet access inside the vm is normal But when I nmap it I get nothin! jeremy@bangkok:~$ nmap -sV -p 1-65535 192.168.1.209 Starting Nmap 5.21 ( http://nmap.org ) at 2012-11-15 18:39 CST Nmap scan report for jeremy (192.168.1.209) Host is up (0.0032s latency). All 65535 scanned ports on jeremy (192.168.1.209) are closed Service detection performed. Please report any incorrect results at http://nmap.org/submit/ Nmap done: 1 IP address (1 host up) scanned in 0.88 seconds ufw and iptables on VM... jeremy@jeremy:~$ sudo service ufw stop [sudo] password for jeremy: ufw stop/waiting jeremy@jeremy:~$ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I have scanned around and have no reason to believe that my router is blocking internal ports. jeremy@bangkok:~$ nmap -v 192.168.1.2 Starting Nmap 5.21 ( http://nmap.org ) at 2012-11-15 18:44 CST Initiating Ping Scan at 18:44 Scanning 192.168.1.2 [2 ports] Completed Ping Scan at 18:44, 0.00s elapsed (1 total hosts) Initiating Parallel DNS resolution of 1 host. at 18:44 Completed Parallel DNS resolution of 1 host. at 18:44, 0.03s elapsed Initiating Connect Scan at 18:44 Scanning 192.168.1.2 [1000 ports] Discovered open port 445/tcp on 192.168.1.2 Discovered open port 139/tcp on 192.168.1.2 Discovered open port 3306/tcp on 192.168.1.2 Discovered open port 80/tcp on 192.168.1.2 Discovered open port 111/tcp on 192.168.1.2 Discovered open port 53/tcp on 192.168.1.2 Discovered open port 5902/tcp on 192.168.1.2 Discovered open port 8090/tcp on 192.168.1.2 Discovered open port 6881/tcp on 192.168.1.2 Completed Connect Scan at 18:44, 0.02s elapsed (1000 total ports) Nmap scan report for 192.168.1.2 Host is up (0.0017s latency). Not shown: 991 closed ports PORT STATE SERVICE 53/tcp open domain 80/tcp open http 111/tcp open rpcbind 139/tcp open netbios-ssn 445/tcp open microsoft-ds 3306/tcp open mysql 5902/tcp open vnc-2 6881/tcp open bittorrent-tracker 8090/tcp open unknown Read data files from: /usr/share/nmap Nmap done: 1 IP address (1 host up) scanned in 0.08 seconds Answer... Turns out all of the ports were open to the network. I installed open ssh and confirmed it. Then I edited my db conf to listen to external IP's and all was well.

    Read the article

  • Not able to run discovery in XenApp 6.5

    - by BDAA
    I am installing a fresh Citrix farm. I installed XenApp 6.5 and configured while configuring the XenApp, added domain\ctxadmin user as the farm administrator. Now when i log into Administrator account into the XenApp server and run discovery it says This user account is not an administrator of this farm, or there was a problem contacting the data store. Check that the data store server for the Citrix XenApp farm is online, and verify that your account is configured and enabled as an administrator on the farm Then I tried to RDP into the XenApp server as ctxadmin user and now I get an error "The Desktop you are trying to open is currently unavailable. Contact you system administrator to confirm the correct settings are in place for your client connection" I believe starting from XenApp version 6.x, once XenApp is installed, then a Citrix Policy needs to be changed as given in http://support.citrix.com/article/CTX124745 But for changing the Citrix policy I need to log into AppCenter which I am not able to do so as I am not able to run discovery as given above. So I am caught up in an end-less loop. Any help would be greatly appreciated

    Read the article

  • libvirt qemu/kvm migration problem

    - by Panda
    I am using kvm and libvirt on my Dell server. Now i am trying to migrate one virtual machine from a physical server to another. However, I failed everytime. In virsh on physicalServer1, I typed: virsh # migrate virtualmachine1 qemu+ssh://username@physicalServer2/system error: operation failed: migration to 'tcp:physicalServer2:49163' failed: migration failed Then I searched FAQ part on libvirt.org. It says: error: operation failed: migration to '...' failed: migration failed This is an error often encountered when trying to migrate with QEMU/KVM. This typically happens with plain migration, when the source VM cannot connect to the destination host. You will want to make sure your hosts are properly configured for migration (see the migration section of this FAQ) I managed to ssh physicalServer2 from a shell on virtualmachine1 so the above red part did not explain my failure. I also open ports on physicalServer2, iptables -L shows following information: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT tcp -- anywhere anywhere state NEW tcp dpts:49152:49215 Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer2: 2011-05-06 13:37:30.708: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-0.14 -enable-kvm -m 2048 -smp 1,sockets=1,cores=1,threads=1 -name openjudge-test -uuid a8c704bc-a4f9-90db-3e57-40e60b00aac1 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/virtualmachine1.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=readline -rtc base=utc -boot c -drive file=/media/nfs/virtualmachine1.img,if=none,id=drive-ide0-0-0,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -netdev tap,fd=20,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=00:16:36:8a:22 :a0,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 127.0.0.1:2 -vga cirrus -incoming tcp:0.0.0.0:49163 -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/0 2011-05-06 13:37:30.915: shutting down The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer1 is empty. Both physical servers are using Ubuntu 11.04. The libvirt and kvm used are installed by apt-get. The libvirt version is 0.8.8.

    Read the article

  • Does WebDAV even work on IIS 7? I say nay

    - by FlavorScape
    I've tried every configuration from the top 10 stack overflow and server fault results for WebDAV 405 on IIS (for verb PROPFIND and PUT). I'm running server 2008 SP2. Followed all the instructions here. I'm no stranger to configuring servers. This has gotten nowhere after 8 hours. Confirmed system.webserver in applicationhost.config: <add name="WebDAV" path="*" verb="PROPFIND,PROPPATCH,MKCOL,PUT,COPY,DELETE,MOVE,LOCK,UNLOCK" modules="WebDAVModule" resourceType="Unspecified" requireAccess="None" /> Port 443 with basic auth, same issue. Tried port 80 with windows auth. Broken. (405) Windows authentication. Check. Added authoring rules for default site and application. Check. Not the firewall. Check. added "Desktop Experience" role feature Tried HTTPS with Basic Authentication on port 443. Does not work. No other services are running like Sharepoint. Check. confirmed user has read/write NT level permissions for the folder/virtual dir tried net use * http://localhost /user:MYDOMAIN\me myPass get error 1920, if I don't authenticate I get error 67 confirmed I'm not applying filtering to WebDAV: <requestFiltering> <fileExtensions applyToWebDAV="false" /> <verbs applyToWebDAV="false" /> <hiddenSegments applyToWebDAV="false" /> 405 - HTTP verb used to access this page is not allowed. The page you are looking for cannot be displayed because an invalid method (HTTP verb) was used to attempt access. SHOULD I JUST GIVE UP? Other questions that helped none: 405 - ‘Method not Allowed’ adding service hosted in IIS7 webdav on iis7.5 - simply cannot make it work http://studentguru.gr/b/kingherc/archive/2009/11/21/webdav-for-iis-7-on-windows-server-2008-r2.aspx

    Read the article

  • Forwarding udp ports iptables packets "lost"?

    - by Dindihi
    I have a Linux router (Debian 6.x) where i forward some ports to internal services. Some tcp ports (like 80, 22...) are OK. I have one Application listening on port 54277udp. No return is coming from this app, i only get Data on this port. Router: cat /proc/sys/net/ipv4/conf/all/rp_filter = 1 cat /proc/sys/net/ipv4/conf/eth0/forwarding = 1 cat /proc/sys/net/ipv4/conf/ppp0/forwarding = 1 $IPTABLES -t nat -I PREROUTING -p udp -i ppp0 --dport 54277 -j DNAT --to-destination $SRV_IP:54277 $IPTABLES -I FORWARD -p udp -d $SRV_IP --dport 54277 -j ACCEPT Also MASQUERADING internal traffic to ppp0(internet) is active & working. Default Policy INPUT&OUTPUT&FORWARD is DROP What is strange, when i do: tcpdump -p -vvvv -i ppp0 port 54277 I get a lot of traffic: 18:35:43.646133 IP (tos 0x0, ttl 57, id 0, offset 0, flags [DF], proto UDP (17), length 57) source.ip > own.external.ip..54277: [udp sum ok] UDP, length 29 18:35:43.652301 IP (tos 0x0, ttl 57, id 0, offset 0, flags [DF], proto UDP (17), length 57) source.ip > own.external.ip..54277: [udp sum ok] UDP, length 29 18:35:43.653324 IP (tos 0x0, ttl 57, id 0, offset 0, flags [DF], proto UDP (17), length 57) source.ip > own.external.ip..54277: [udp sum ok] UDP, length 29 18:35:43.655795 IP (tos 0x0, ttl 57, id 0, offset 0, flags [DF], proto UDP (17), length 57) source.ip > own.external.ip..54277: [udp sum ok] UDP, length 29 18:35:43.656727 IP (tos 0x0, ttl 57, id 0, offset 0, flags [DF], proto UDP (17), length 57) source.ip > own.external.ip..54277: [udp sum ok] UDP, length 29 18:35:43.659719 IP (tos 0x0, ttl 57, id 0, offset 0, flags [DF], proto UDP (17), length 57) source.ip > own.external.ip..54277: [udp sum ok] UDP, length 29 tcpdump -p -i eth0 port 54277 (on the same machine, the router) i get much less traffic. also on the destination $SRV_IP there are only a few packets coming in, but not all. INTERNAL SERVER: 19:15:30.039663 IP source.ip.52394 > 192.168.215.4.54277: UDP, length 16 19:15:30.276112 IP source.ip.52394 > 192.168.215.4.54277: UDP, length 16 19:15:30.726048 IP source.ip.52394 > 192.168.215.4.54277: UDP, length 16 So some udp ports are "ignored/dropped" ? Any idea what could be wrong? Edit: This is strange: The Forward rule has data packets, but the PREROUTING rule has 0 packets... iptables -nvL -t filter |grep 54277 Chain FORWARD (policy DROP 0 packets, 0 bytes) 168 8401 ACCEPT udp -- * * 0.0.0.0/0 192.168.215.4 state NEW,RELATED,ESTABLISHED udp dpt:54277 iptables -nvL -t nat |grep 54277 Chain PREROUTING (policy ACCEPT 405 packets, 24360 bytes) 0 0 DNAT udp -- ppp0 * 0.0.0.0/0 my.external.ip udp dpt:54277 state NEW,RELATED,ESTABLISHED to:192.168.215.4

    Read the article

  • OpenVPN Clients using server's connection (with no default gateway)

    - by Branden Martin
    I wanted an OpenVPN server so that I could create a private VPN network for staff to connect to the server. However, not as planned, when clients connect to the VPN, it's using the VPN's internet connection (ex: when going to whatsmyip.com, it's that of the server and not the clients home connection). server.conf local <serverip> port 1194 proto udp dev tun ca ca.crt cert x.crt key x.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt client-to-client keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 9 client.conf client dev tun proto udp remote <srever> 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert x.crt key x.key ns-cert-type server comp-lzo verb 3 Server's route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 69.64.48.0 * 255.255.252.0 U 0 0 0 eth0 default static-ip-69-64 0.0.0.0 UG 0 0 0 eth0 default static-ip-69-64 0.0.0.0 UG 0 0 0 eth0 default static-ip-69-64 0.0.0.0 UG 0 0 0 eth0 Server's IP Tables Chain INPUT (policy ACCEPT) target prot opt source destination fail2ban-proftpd tcp -- anywhere anywhere multiport dports ftp,ftp-data,ftps,ftps-data fail2ban-ssh tcp -- anywhere anywhere multiport dports ssh ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:20000 ACCEPT tcp -- anywhere anywhere tcp dpt:webmin ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT tcp -- anywhere anywhere tcp dpt:www ACCEPT tcp -- anywhere anywhere tcp dpt:imaps ACCEPT tcp -- anywhere anywhere tcp dpt:imap2 ACCEPT tcp -- anywhere anywhere tcp dpt:pop3s ACCEPT tcp -- anywhere anywhere tcp dpt:pop3 ACCEPT tcp -- anywhere anywhere tcp dpt:ftp-data ACCEPT tcp -- anywhere anywhere tcp dpt:ftp ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:smtp ACCEPT tcp -- anywhere anywhere tcp dpt:ssh ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain fail2ban-proftpd (1 references) target prot opt source destination RETURN all -- anywhere anywhere Chain fail2ban-ssh (1 references) target prot opt source destination RETURN all -- anywhere anywhere My goal is that clients can only talk to the server and other clients that are connected. Hope I made sense. Thanks for the help!

    Read the article

  • Gentoo Linux useful utilities

    - by Alakdae
    I want to make a list of utilities that come in handy in Gentoo (general Linux tools available in all distributions also appreciated). What tools and commands do you use and consider helpful in administration of a Gentoo server? I will update the list with command from answers from time to time. eclean Utility for cleaning distfiles and binary packages. Usage example: eclean distfiles Usage example output: Cleans out the files in /usr/portage/distfiles. Pretty handy. Package: app-portage/gentoolkit eix Very useful tool for getting information about a package. Similar to "emerge -s" but much faster and more precise. Usage example: eix gentoolkit Usage example output: Show information about package such as: available versions, masked versions, installed versions and description. Package: app-portage/eix eix-test-obsolete Check system for obsolete, redundant, uninstalled entries in package.keywords, package.mask, package.unmask, package.use and package.cflags Usage example: eix-test-obsolete Usage example output: Shows non-matching entries, redundant entries, and uninstalled entries. Package: app-portage/eix equery Another very useful tool for getting information about packages (listing package files, checking which files belong to which package and much more) Usage example: equery b emerge Usage example output: Show which packages installed a file called emerge Package: app-portage/gentoolkit genlop Utility for extracting information about emerged ebuilds Usage example: genlop -l --date yesterday Usage example output: Show a list of packages that have been emerged yesterdayPackage: app-portage/genlop glsa-check Checks system if it's affected by GLSAs (security issues) Usage example: glsa-check -l affected Usage example output: List of GLSA that the system is affected by. Package: app-portage/gentoolkit rc-update Utility for managing (adding, deleting) runlevel scripts. Usage example: rc-update add syslog-ng default Usage example output: Adds syslog-ng to default runlevel. Package: sys-apps/baselayout revdep-rebuild Scans libraries and binaries for missing shared library dependencies Usage example: revdep-rebuild Usage example output: Gather binaries and libraries information, check for dependencies, rebuild packages with missing dependencies Package: app-portage/gentoolkit

    Read the article

  • CUPS basic auth error through web interface

    - by Inaimathi
    I'm trying to configure CUPS to allow remote administration through the web interface. There's enough documentation out there that I can figure out what to change in my cupsd.conf (changing Listen localhost:631 to Port 631, and adding Allow @LOCAL to the /, /admin and /admin/conf sections). I'm now at the point where I can see the CUPS interface from another machine on the same network. The trouble is, when I try to Add Printer, I'm asked for a username and password, but my response is rejected even when I know I've gotten it right (I assume it's asking for the username and password of someone in the lpadmin group on the server machine; I've sshed in with credentials its rejecting, and the user I'm using has been added to the lpadmin group). If I disable auth outright, by changing DefaultAuthType Basic to DefaultAuthType None, I get an "Unauthorized" error instead of a password request when I try to Add Printer. What am I doing wrong? Is there a way of letting users from the local network to administer the print server through the CUPS web interface? EDIT: By request, my complete cupsd.conf (spoiler: minimally edited default config file that comes with the edition of CUPS from the Debian wheezy repos): LogLevel warn MaxLogSize 0 SystemGroup lpadmin Port 631 # Listen localhost:631 Listen /var/run/cups/cups.sock Browsing On BrowseOrder allow,deny BrowseAllow all BrowseLocalProtocols CUPS dnssd # DefaultAuthType Basic DefaultAuthType None WebInterface Yes <Location /> Order allow,deny Allow @LOCAL </Location> <Location /admin> Order allow,deny Allow @LOCAL </Location> <Location /admin/conf> AuthType Default Require user @SYSTEM Order allow,deny Allow @LOCAL </Location> # Set the default printer/job policies... <Policy default> # Job/subscription privacy... JobPrivateAccess default JobPrivateValues default SubscriptionPrivateAccess default SubscriptionPrivateValues default # Job-related operations must be done by the owner or an administrator... <Limit Create-Job Print-Job Print-URI Validate-Job> Order deny,allow </Limit> <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job Cancel-My-Jobs Close-Job CUPS-Move-Job CUPS-Get-Document> Require user @OWNER @SYSTEM Order deny,allow </Limit> # All administration operations require an administrator to authenticate... <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default CUPS-Get-Devices> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # All printer operations require a printer operator to authenticate... <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After Cancel-Jobs CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # Only the owner or an administrator can cancel or authenticate a job... <Limit Cancel-Job CUPS-Authenticate-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order deny,allow </Limit> </Policy> # Set the authenticated printer/job policies... <Policy authenticated> # Job/subscription privacy... JobPrivateAccess default JobPrivateValues default SubscriptionPrivateAccess default SubscriptionPrivateValues default # Job-related operations must be done by the owner or an administrator... <Limit Create-Job Print-Job Print-URI Validate-Job> AuthType Default Order deny,allow </Limit> <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job Cancel-My-Jobs Close-Job CUPS-Move-Job CUPS-Get-Document> AuthType Default Require user @OWNER @SYSTEM Order deny,allow </Limit> # All administration operations require an administrator to authenticate... <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # All printer operations require a printer operator to authenticate... <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After Cancel-Jobs CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # Only the owner or an administrator can cancel or authenticate a job... <Limit Cancel-Job CUPS-Authenticate-Job> AuthType Default Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order deny,allow </Limit> </Policy>

    Read the article

  • Configuring Fortigate OS4 for FTPS

    - by Paul
    I configured iis7 ftp to allow ssl connections. I set the ssl firewall to use ports 50000-50050. If I set up a custom service on my fortigate firewall for ftps with source ports 990-50050 and destination ports 990-50050, set it to a firewall policy and connect from a client it connects and works successfully. If I create a service FTPS Control with source port 990 and destination port 990 and another service,FTP Data with source ports 50000-50050 and destination ports 50000-50050 add them to a group FTPSSL, replace the ftps policy with FTPSSL and try connecting it tries to connect to port 990 and eventually times out. Is there a way to configure the service to only use the ports I need and not every port from 990 up?

    Read the article

  • Open ports broken from internal network

    - by ksvi
    Quick summary: Forwarded port works from the outside world, but from the internal network using the external IP the connection is refused. This is a simplified situation to make the explanation easier: I have a computer that is running a service on port 12345. This computer has an internal IP 192.168.1.100 and is connected directly to a modem/router which has internal IP 192.168.1.1 and external (public, static) IP 1.2.3.4. (The router is TP-LINK TD-w8960N) I have set up port forwarding (virtual server) at port 12345 to go to port 12345 at 192.168.1.100. If I run telnet 192.168.1.100 12345 from the same computer everything works. But running telnet 1.2.3.4 12345 says connection refused. If I do this on another computer (on the same internal network, connected to the router) the same thing happens. This would seem like the port forwarding is not working. However... If I run a online port checking service on my external IP and the service port it says the port is open and I can see the remote server connecting and immediately closing connection. And using another computer that is connected to the internet using a mobile connection I can also use telnet 1.2.3.4 12345 and I get a working connection. So the port forwarding seems to be working, however using external IP from the internal network doesn't. I have no idea what can be causing this, since another setup very much like this (different router) works for me. I can access a service running on a server from inside the network both through the internal and external IP. Note: I know I could just use the internal IP inside of the network to access this service. But if I have a laptop that must be able to do this both from inside and outside it would be annoying to constantly switch between 1.2.3.4 and 192.168.1.100 in the software configuration. Router output: > iptables -t nat -L -n Chain PREROUTING (policy ACCEPT) target prot opt source destination ACCEPT all -- 0.0.0.0/0 224.0.0.0/3 DNAT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:25 to:192.168.1.101 DNAT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:25 to:192.168.1.101 DNAT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:110 to:192.168.1.101 DNAT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:12345 to:192.168.1.102 DNAT udp -- 0.0.0.0/0 192.168.1.1 udp dpt:53 to:217.118.96.203 Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- 192.168.1.0/24 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) target prot opt source destination

    Read the article

  • Set certain WSUS updates to auto-install

    - by Nicolas
    We're running a WSUS server for the simple purpose of caching updates. Since we are a very small network of all "power users", we've got the domain group policy for WSUS updates on the clients set to prompt for download/install. i.e. We don't want updates to install without our knowledge. But there are a few cases where it would be nice to be able to set a certain update to auto-install. e.g. Windows Defender updates, Malicious Software Removal Tool, Outlook Junk Email Filter, etc. Basically all the silly little updates that you would always install anyway and don't require a restart. Is there a way to set the general policy to prompt for download/install, but auto-install certain regular updates? P.S. WSUS itself does have the facility to auto-approve certain updates. That part works. Facts & Figures: SBS 2003 domain Windows 7 Pro clients Windows XP Pro clients

    Read the article

  • How do I enable SELinux when booting a ramdisk from a CD/DVD?

    - by JeffG
    I have a bootable DVD which boots the same Kernel as the Hard Drive (which uses SELinux). I have copied /etc/selinux and all kernel modules to my ramdisk, and have tried various combinations of selinux=1 and selinux 1 with enforcing 1 and enforcing 0. as Kernel boot parameters. All files contained in the checkpolicy, libselinux, policycoreutils, selinux-policy and selinux-policy-targeted rpms have also been copied into the ramdisk tree. After the system boots from the ramdisk, I check dmesg: % dmesg | grep -i selinux Kernel command line: initrd=idrd.img ramdisk_size=110476 selinux=1 SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability SElinux: Registering netfilter hooks But SELinux isn't running: % /usr/sbin/getenforce Disabled % /usr/sbin/setenforce 1 /usr/sbin/setenforce: SELinux is disabled Neither /var/log/messages nor /proc/kmsg hold clues.

    Read the article

  • litespeed issue with content-type

    - by sandeep.s85
    I am running magento with litespeed. The problem I am facing is that ajax call is being made of which header is set as x-json, but lightspeed is setting another header of text/html content type I've checked that page with apache and everything is working fine. I checked the response headers with apache and litespeed and here are they: With apache: HTTP/1.1 200 OK Date: Fri, 07 Sep 2012 05:58:47 GMT Server: Apache Expires: Thu, 19 Nov 1981 08:52:00 GMT Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma: no-cache Set-Cookie: frontend=164b21c64808a05e806027bdbd4d745d; expires=Fri, 07-Sep-2012 06:58:48 GMT; path=/; domain=mydomain.com; httponly Connection: close Transfer-Encoding: chunked Content-Type: application/x-json With litespeed: HTTP/1.1 200 OK Date: Fri, 07 Sep 2012 06:10:55 GMT Server: LiteSpeed Connection: close Expires: Thu, 19 Nov 1981 08:52:00 GMT Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 Pragma: no-cache Set-Cookie: frontend=164b21c64808a05e806027bdbd4d745d; expires=Fri, 07-Sep-2012 07:10:55 GMT; path=/; domain=mydomain.com; httponly Content-Type: text/html; charset=UTF-8 Content-Length: 474 Vary: User-Agent I've also added application/json to mime.properties of litespeed,restarted it but that did not work. Here is the screenshot

    Read the article

  • Installing Yaws server on Ubuntu 12.04 (Using a cloud service)

    - by Lee Torres
    I'm trying to get a Yaws web server working on a cloud service (Amazon AWS). I've compilled and installed a local copy on the server. My problem is that I can't get Yaws to run while running on either port 8000 or port 80. I have the following configuration in yaws.conf: port = 8000 listen = 0.0.0.0 docroot = /home/ubuntu/yaws/www/test dir_listings = true This produces the following successful launch/result: Eshell V5.8.5 (abort with ^G) =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Using config file /home/ubuntu/yaws.conf =INFO REPORT==== 16-Sep-2012::17:21:06 === Ctlfile : /home/ubuntu/.yaws/yaws/default/CTL =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Listening to 0.0.0.0:8000 for <3> virtual servers: - http://domU-12-31-39-0B-1A-F6:8000 under /home/ubuntu/yaws/www/trial - =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Listening to 0.0.0.0:4443 for <1> virtual servers: - When I try to access the the url (http://ec2-72-44-47-235.compute-1.amazonaws.com), it never connects. I've tried using paping to check if port 80 or 8000 is open(http://code.google.com/p/paping/) and I get a "Host can not be resolved" error, so obviously something isn't working. I've also tried setting the yaws.conf so its at Port 80, appearing like this: port = 8000 listen = 0.0.0.0 docroot = /home/ubuntu/yaws/www/test dir_listings = true and I get the following error: =ERROR REPORT==== 16-Sep-2012::17:24:47 === Yaws: Failed to listen 0.0.0.0:80 : {error,eacces} =ERROR REPORT==== 16-Sep-2012::17:24:47 === Can't listen to socket: {error,eacces} =ERROR REPORT==== 16-Sep-2012::17:24:47 === Top proc died, terminate gserv =ERROR REPORT==== 16-Sep-2012::17:24:47 === Top proc died, terminate gserv =INFO REPORT==== 16-Sep-2012::17:24:47 === application: yaws exited: {shutdown,{yaws_app,start,[normal,[]]}} type: permanent {"Kernel pid terminated",application_controller," {application_start_failure,yaws,>>>>>>{shutdown,>{yaws_app,start,[normal,[]]}}}"} I've also opened up the port 80 using iptables. Running sudo iptables -L gives this output: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- ip-192-168-2-0.ec2.internal ip-192-168-2-16.ec2.internal tcp dpt:http ACCEPT tcp -- 0.0.0.0 anywhere tcp dpt:http ACCEPT all -- anywhere anywhere ctstate RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:http Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination In addition, I've gone to the security group panel in the Amazon AWS configuration area, and add ports 80, 8000, and 8080 to ip source 0.0.0.0 Please note: if you try to access the URL of the virtual server now, it likely won't connect because I'm not running currently running the yaws daemon. I've tested it when I've run yaws either through yaws or yaws -i Thanks for the patience

    Read the article

  • Ports do not open after rules appended in iptables

    - by user2699451
    I have a server that I am trying to setup for OpenVPN. I have followed all the steps, but I see that when I try to connect to it in Windows, it doesn't allow me, it just hangs on connecting, so I did a nmap scan and I see that port 1194 is not open so naturally I append the rule to open 1194 with: iptables -A INPUT -i eth0 -p tcp --dport 1194 -j ACCEPT followed by service iptables save and service iptables restart which all executed successfully. Then I try again, but it doesn't work and another nmap scan says that port 1194 is closed. Here is the iptables configuration: # Generated by iptables-save v1.4.7 on Thu Oct 31 09:47:38 2013 *nat :PREROUTING ACCEPT [27410:3091993] :POSTROUTING ACCEPT [0:0] :OUTPUT ACCEPT [5042:376160] -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -j SNAT --to-source 41.185.26.238 -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE COMMIT # Completed on Thu Oct 31 09:47:38 2013 # Generated by iptables-save v1.4.7 on Thu Oct 31 09:47:38 2013 *filter :INPUT ACCEPT [23571:2869068] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [27558:3656524] :vl - [0:0] -A INPUT -p tcp -m tcp --dport 5252 -m comment --comment "SSH Secure" -j ACCEPT -A INPUT -p icmp -m icmp --icmp-type 8 -m state --state NEW,RELATED,ESTABLISHED -$ -A INPUT -i lo -j ACCEPT -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --dport 22 -m comment --comment "SSH" -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -m comment --comment "HTTP" -j ACCEPT -A INPUT -p tcp -m tcp --dport 8080 -m comment --comment "HTTPS" -j ACCEPT -A INPUT -p tcp -m tcp --dport 443 -m comment --comment "HTTP Encrypted" -j ACCEP$ -A INPUT -i eth0 -p tcp -m tcp --dport 1723 -j ACCEPT -A INPUT -i eth0 -p gre -j ACCEPT -A INPUT -p udp -m udp --dport 1194 -j ACCEPT -A FORWARD -i ppp+ -o eth0 -j ACCEPT -A FORWARD -i eth0 -o ppp+ -j ACCEPT -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -s 10.8.0.0/24 -j ACCEPT -A FORWARD -j REJECT --reject-with icmp-port-unreachable -A OUTPUT -p icmp -m icmp --icmp-type 0 -m state --state RELATED,ESTABLISHED -j A$ COMMIT # Completed on Thu Oct 31 09:47:38 2013 and my nmap scan from: localhost: nmap localhost Starting Nmap 5.51 ( http://nmap.org ) at 2013-10-31 09:53 SAST Nmap scan report for localhost (127.0.0.1) Host is up (0.000011s latency). Other addresses for localhost (not scanned): 127.0.0.1 Not shown: 996 closed ports PORT STATE SERVICE 22/tcp open ssh 25/tcp open smtp 443/tcp open https 1723/tcp open pptp Nmap done: 1 IP address (1 host up) scanned in 0.06 seconds remote pc: nmap [server ip] Starting Nmap 6.00 ( http://nmap.org ) at 2013-10-31 09:53 SAST Nmap scan report for rla04-nix1.wadns.net (41.185.26.238) Host is up (0.025s latency). Not shown: 858 filtered ports, 139 closed ports PORT STATE SERVICE 22/tcp open ssh 443/tcp open https 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 15.70 seconds So, I do not know what is causing this, any assistance will be appreciated! UPDATE AFTER FIRST ANSWER::: [root@RLA04-NIX1 ~]# iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT [root@RLA04-NIX1 ~]# iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT [root@RLA04-NIX1 ~]# iptables -A FORWARD -j REJECT [root@RLA04-NIX1 ~]# iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE [root@RLA04-NIX1 ~]# service iptables save iptables: Saving firewall rules to /etc/sysconfig/iptables:[ OK ] [root@RLA04-NIX1 ~]# service iptables restart iptables: Flushing firewall rules: [ OK ] iptables: Setting chains to policy ACCEPT: filter nat [ OK ] iptables: Unloading modules: [ OK ] iptables: Applying firewall rules: [ OK ] [root@RLA04-NIX1 ~]# lsof -i :1194 -bash: lsof: command not found iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:5252 /* SSH Secure */ ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 state NEW,RELATED,ESTABLISHED ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 /* SSH */ ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 /* HTTP */ ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:8080 /* HTTPS */ ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:443 /* HTTP Encrypted */ ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:1723 ACCEPT 47 -- 0.0.0.0/0 0.0.0.0/0 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:1194 Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 0.0.0.0/0 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 0.0.0.0/0 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 0 state RELATED,ESTABLISHED Chain vl (0 references) target prot opt source destination [root@RLA04-NIX1 ~]# nmap localhostt Starting Nmap 5.51 ( http://nmap.org ) at 2013-10-31 11:13 SAST remote pc nmap [server ip] Starting Nmap 6.00 ( http://nmap.org ) at 2013-10-31 11:11 SAST Nmap scan report for rla04-nix1.wadns.net (41.185.26.238) Host is up (0.020s latency). Not shown: 858 filtered ports, 139 closed ports PORT STATE SERVICE 22/tcp open ssh 443/tcp open https 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 4.18 seconds localhost nmap localhost Starting Nmap 5.51 ( http://nmap.org ) at 2013-10-31 11:13 SAST Nmap scan report for localhost (127.0.0.1) Host is up (0.000011s latency). Other addresses for localhost (not scanned): 127.0.0.1 Not shown: 996 closed ports PORT STATE SERVICE 22/tcp open ssh 25/tcp open smtp 443/tcp open https 1723/tcp open pptp Nmap done: 1 IP address (1 host up) scanned in 0.06 seconds UPDATE AFTER SCANNING UDP PORTS Sorry, I am noob, I am still learning, but here is the output for: nmap -sU [server ip] Starting Nmap 6.00 ( http://nmap.org ) at 2013-10-31 11:33 SAST Nmap scan report for [server address] ([server ip]) Host is up (0.021s latency). Not shown: 997 open|filtered ports PORT STATE SERVICE 53/udp closed domain 123/udp closed ntp 33459/udp closed unknown Nmap done: 1 IP address (1 host up) scanned in 8.57 seconds btw, no changes have been made since post started (except for iptables changes)

    Read the article

  • Using NPS to restrict access to WLAN

    - by eric.s
    We currently have one WLAN that only domain users can connect to. We will be adding a guest WLAN and would like all non-domain machines to use this, even if a user has a domain account. We have set up NPS and can log in against it, but we can not restrict the connection option to be a domain computer AND a domain account. As a network policy it states that it moves along through each policy until it finds one that it accepts or runs out. For connection request policies Domain Computers is not an option. This is where I thought I may be able to stop it. Has anyone been able to successfully restrict this without manually adding MACs to the WLAN Controller?

    Read the article

  • Enabling ppolicy in openldap

    - by nitins
    For enabling ppolicy is in Openldap I am trying to import the policy given below. dn: ou=policies,dc=example,dc=in ou: policies objectClass: top objectClass: organizationalUnit # default, policies, example.in dn: cn=default,ou=policies,dc=example,dc=in objectClass: top objectClass: device objectClass: pwdPolicy cn: default pwdAttribute: userPassword pwdMaxAge: 7776002 pwdExpireWarning: 432000 pwdInHistory: 0 pwdCheckQuality: 1 pwdMinLength: 8 pwdMaxFailure: 5 pwdLockout: TRUE pwdLockoutDuration: 900 pwdGraceAuthNLimit: 0 pwdFailureCountInterval: 0 pwdMustChange: TRUE pwdAllowUserChange: TRUE pwdSafeModify: FALSE But I am getting the error given below. ldapadd -x -D "cn=Manager,dc=example,dc=in" -w xxxxxx -f /tmp/new-policy.ldif adding new entry "cn=default,ou=policies,dc=example,dc=in" ldapadd: Invalid syntax (21) additional info: pwdAttribute: value #0 invalid per syntax Any idea on why I am getting the error ? I have already added the ppolicy schema and module in slapd.conf

    Read the article

  • PKI Issuing CA on Domain Controllers

    - by dunxd
    I am setting up a PKI which will initially be used internally. As we may grow our use of this I have opted for a three tier hierarchy - Offline Root and Policy CAs (one Policy CA at the moment for internal use), and online issuing CAs. We had initially discussed using our Domain Controllers as the Issuing CAs rather than setting up dedicated ones. I am now starting to have doubts about whether it is a good idea to have our DCs do certificate issuing. We have less than 1000 users, so our DCs aren't hugely taxed. Does anyone have any suggestions for or against doing this? We are currently running Windows 2003 Active Directory, but will be upgrading to Windows 2008 in the coming year. I'm setting up Windows 2008 PKI.

    Read the article

  • Haproxy ACL for balance on URL request

    - by Elgreco08
    I'm usung Ubuntu with haproxy 1.4.13 version. Its load balancing two subdomains: app1.domain.com app2.domain.com now i want to be able to use ACL to send based on url request to the right backends For example: http://app1.domain.com/path/games/index.php sould be send to backend1 http://app1.domain.com/path/photos/index.php should be send to backend2 http://app2.domain.com/path/mail/index.php sould be send to backend3 http://app2.domain.com/path/wazap/index.php should be send to backend4 i did used the code the the following acl frontend http-farm bind 0.0.0.0:80 acl app1web hdr_beg(host) -i app1 # for http://app1.domain.com acl app2web hdr_beg(host) -i app2 # for http://app2.domain.com acl msg-url-1 url_reg ^\/path/games/.* acl msg-url-2 url_reg ^\/path/photos/.* acl msg-url-3 url_reg ^\/path/mail/.* acl msg-url-4 url_reg ^\/path/wazap/.* use_backend games if msg-url-1 app1web use_backend photos if msg-url-2 app2web use_backend mail if ..... backend games option httpchk GET /alive.php HTTP/1.1\r\nHost:\ app1.domain.com option forwardfor balance roundrobin server appsrv-1 192.168.1.10:80 check inter 2000 fall 3 server appsrv-2 192.168.1.11:80 check inter 2000 fall 3 backend photos option httpchk GET /alive.php HTTP/1.1\r\nHost:\ app2.domain.com option forwardfor balance roundrobin server appsrv-1 192.168.1.13:80 check inter 2000 fall 3 server appsrv-2 192.168.1.14:80 check inter 2000 fall 3 .... Since the path mail, photos...etc will be application pools on iis, i want to monitor them if they are alive, if the pool does not respond it should stop serving it. my problem is for sure in the regular expression in the ACL acl msg-url-4 url_reg ^\/path/wazap/.* What should i change in the ACL to make it work ? thanks for any hints

    Read the article

  • iptables blocking ssh communication

    - by Michal Sapsa
    I'm using this script for iptables: #!/bin/sh echo "1" > /proc/sys/net/ipv4/ip_forward iptables -F iptables -X iptables -F -t nat iptables -X -t nat iptables -F -t filter iptables -X -t filter iptables -t filter -P FORWARD DROP iptables -t filter -A FORWARD -s 192.168.0.0/255.255.0.0 -d 0/0 -j ACCEPT iptables -t filter -A FORWARD -s 0/0 -d 192.168.0.0/255.255.0.0 -j ACCEPT iptables -t nat -A POSTROUTING -s 10.8.0.1/255.255.255.0 -j MASQUERADE iptables -A FORWARD -s 10.8.0.1/255.255.255.0 -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.0.0/24 -d 0/0 -j MASQUERADE iptables -I FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu iptables -t nat -A PREROUTING -i eth1 -p udp --dport 16161 -j DNAT --to 192.168.0.251:16161 iptables -t nat -A PREROUTING -i eth1 -p udp --sport 16161 -j DNAT --to 192.168.0.251:16161 #openvpn iptables -I INPUT -p tcp --dport 1194 -j ACCEPT iptables -I INPUT -p udp --dport 1194 -j ACCEPT I end up with some iptables rules that should work but don't work - probably because of me. # Generated by iptables-save v1.4.12 on Mon May 26 13:15:43 2014 *raw :PREROUTING ACCEPT [1657523:1357257330] :OUTPUT ACCEPT [36804:34834370] -A PREROUTING -p icmp -j TRACE -A PREROUTING -p tcp -j TRACE -A OUTPUT -p icmp -j TRACE -A OUTPUT -p tcp -j TRACE COMMIT # Completed on Mon May 26 13:15:43 2014 # Generated by iptables-save v1.4.12 on Mon May 26 13:15:43 2014 *nat :PREROUTING ACCEPT [5033:345623] :INPUT ACCEPT [154:34662] :OUTPUT ACCEPT [6:1968] :POSTROUTING ACCEPT [2:120] -A PREROUTING -i eth0 -p tcp -m tcp --dport 16161 -j DNAT --to-destination 192.168.0.251:22 -A PREROUTING -i eth1 -p tcp -m tcp --dport 16161 -j DNAT --to-destination 192.168.0.251:22 -A POSTROUTING -s 10.8.0.0/24 -j MASQUERADE -A POSTROUTING -s 192.168.0.0/24 -j MASQUERADE COMMIT # Completed on Mon May 26 13:15:44 2014 # Generated by iptables-save v1.4.12 on Mon May 26 13:15:44 2014 *filter :INPUT ACCEPT [548:69692] :FORWARD DROP [8:384] :OUTPUT ACCEPT [2120:1097479] -A INPUT -p udp -m udp --dport 1194 -j ACCEPT -A INPUT -p tcp -m tcp --dport 1194 -j ACCEPT -A FORWARD -p tcp -m tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu -A FORWARD -s 192.168.0.0/16 -j ACCEPT -A FORWARD -d 192.168.0.0/16 -j ACCEPT -A FORWARD -s 10.8.0.0/24 -j ACCEPT -A FORWARD -i eth0 -o eth1 -p tcp -m tcp --dport 22 -j ACCEPT -A FORWARD -i eth1 -o eth0 -p tcp -m tcp --dport 22 -j ACCEPT COMMIT TRACE at PREROUTEING AND OUTPUT are only for debuging this thing. When I ssh at public ip with port 16161 I don't get any message, only TimeOut so it looks like I don't get communication back to remote server. ETH0 is the world, ETH1 is LAN Any IPTABLES Masters willing to give a hand ? iptables -vL Chain INPUT (policy ACCEPT 20548 packets, 3198K bytes) pkts bytes target prot opt in out source destination 38822 7014K ACCEPT udp -- any any anywhere anywhere udp dpt:openvpn 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:openvpn Chain FORWARD (policy DROP 1129 packets, 64390 bytes) pkts bytes target prot opt in out source destination 214K 11M TCPMSS tcp -- any any anywhere anywhere tcpflags: SYN,RST/SYN TCPMSS clamp to PMTU 4565K 1090M ACCEPT all -- any any 192.168.0.0/16 anywhere 5916K 7315M ACCEPT all -- any any anywhere 192.168.0.0/16 0 0 ACCEPT all -- any any 10.8.0.0/24 anywhere 0 0 ACCEPT tcp -- any any anywhere 192.168.0.251 tcp dpt:16161 Chain OUTPUT (policy ACCEPT 59462 packets, 19M bytes) pkts bytes target prot opt in out source destination

    Read the article

< Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >