Search Results

Search found 17018 results on 681 pages for 'floppy disk drive'.

Page 144/681 | < Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >

• aligning truecrypt partition on 1.5TB 4kB sector drive

  - by pQd

  hi, aligning partitions to start at real physical sector of ssds / stripped raids / 4kB drives is a 'good thing to do'. but i've run into a problems when trying to do it for a truecrypt partition that will contain ext3 on it. or so it seems. when drive is question is partitioned properly and formatted with ext3 i get very reasonable write speeds around 70-80MB/s, but when i put truecrypt and ext3 on the top of it write performance becomes very unstable and goes between 1-25MB/s with very high io-wait. on the same server i dont have any performance issues with ext3 on the top of truecrypt on regular 512B-sector 500GB sata disks. so my best guess is that iowaits are caused by misalignment but i cannot really find reliable information on how to calculate optimal partition beginning. i've tried to start it at 128 logical sector, i've also tried 8132 sector as suggested here but both gave me very bad and unstable performance. do you have any experience with similar setup? thanks!

  Read the article

• CA ArcServe r11.1 - have to switch Tape Drive Offline then Online to finish backup

  - by Richard

  Ill keep it brief, I have an HP Ultrium 1 in a server currently running CA ArcServe r11.1. I have 5 daily backup tapes, each of which are new. 3 of the 5 work fine without intervention but 2 of them stop at varying points through the backup asking for a new tape, even though that tape is not full. The way I have found around this is to switch the tape drive offline for 10 minutes then switch it back online, whilst the backup is still running. Has anyone ever seen this before? If so, any ideas how to permanently fix this. If all else fails just some pointers in the right direction. Thanks

  Read the article

• Sharing an external hard drive in Ubuntu using Samba

  - by cambraca

  /media/MYDISK is where my hard drive is mounted automatically. I created a symlink using: ln -s /media/MYDISK /home/camilo/MYDISK chmod 777 /home/camilo/MYDISK I'm setting up smb.conf like this: [myshare1] comment = external disk browsable = yes path = /home/camilo/MYDISK guest ok = yes read only = no create mask = 0775 Also, in the [global] section I tried adding the following lines: follow symlinks = yes wide links = yes unix extensions = no The problem is that when browsing the shared folder in Windows 7, I get a "\\etc\myshare1 is not accessible" error. When pointing the path to a regular folder it works fine. Also, when I point it directly to /media/MYDISK, it shows the same error. EDIT: to make it more interesting, I have no graphical interface, so I need to touch the config files directly..

  Read the article

• How to recover data from a drive that was erased during the Ubuntu installation?

  - by user110353

  Yesterday I had two NTFS partitions on my drive. One on which Windows 7 was installed (C Drive) and the other contained my data (D Drive). During Ubuntu installation I choose to install Ubuntu and erase my existing OS. When Ubuntu installed, I was shocked to see no partition. All my data was gone. I must have done something wrong in selecting my option during installation. Is there any way I can recover my D Drive? Thanks in advance.

  Read the article

• Ten latest files on disk

  - by Artic

  I need effective algorithm to keep only ten latest files on disk in particular folder to support some kind of publishing process. Only 10 files should present in this folder at any point of time. Please, give your advises what should be used here.

  Read the article

• Computer randomly shuts down with a fading alarm power button and CD drive

  - by Shad

  I am currently experiencing something very very odd. Having build my PC myself, I have never had any issues (or anything heat related). A few moments ago my computer shut down very randomly and everything goes blank, when I looked down on my case's power button it was fading on and off in such way I've had never seen before. I noticed the CD drive all of a sudden also started blinking randomly. What do you guys think this problem is related to? It is definitely not a overheating issue and I am pretty sure my 600 watt power supply didn't blow because right now I am able to turn it on and boot up the PC but 20 seconds later it shuts down (sometimes doesn't shut down for 2 minutes). I have no idea what this is... My specs are (built by myself): i5 3570k (unoverclocked) GTX 560ti Asrock Z77 Pro4-M motherboard 8GB Vengeance RAM 600W Corsair power supply 500GB of Seagate HD Case: Corsair Carbide 300R

  Read the article

• Need Help with fixing permissions in mounted Drive

  - by Master

  I am trying a lot still my problem is not solved. I have a partion called Server and inside it i have 5 folders like Folder 1 FOlder 2 Folder 3 I am mounting the drive on startup by using following command as told to me by some senoir members and it works but with some problems /dev/sdb1 /media/Server ntfs defaults,umask=006,fmask=000,dmask=007,uid=1000,gid=1001 0 0 The problem is with this command the permission are applied to all folders like Folder 1 , Folder 2 , FOlder3 But i want that only FOlder 3 should be publicly readable and writable while all other should be private and no one should have access to that. How can i achieve that

  Read the article

• Using the link command to keep backups on another drive

  - by Xavier

  I have a folder that contains a not so large amount of space called /data/backup. I have been told that if I link that folder (/data/backup) to an even bigger folder area like /bigdata/backup for example, that I will be able to execute backups to the /data/backup folder. It will then just create a link, but the data will be seen in both folders and the latter one (/bigdata/backup) will contain the backup results but it will show on both folders. Since the /bigdata/backup has far more disk space then the backup will no longer fail because of space problems in the /data/backup one. Is this true?

  Read the article

• Google Drive stripped Outlook 2010 of all emails, contacts, etc

  - by David

  I have a business that requires I use the business email: [email protected] I loaded Google Drive as a free cloud to share project details with co-worker. Side effect is that Outlook 2010 does not work now. All incoming emails are now transferred to my personal Google account. Now I can not send business emails inclusive of business headers and footers since Outlook is erroring on send/receive. And all my history of email organization on Outlook is gone. I was previously successfully syncing outlook through Google calendar to keep my blackberry sync'd Your help is appreciated - thank you. David

  Read the article

• windows phone 7 ctp - drive cannot locate a specific area or track on the disk

  - by Andy Clarke

  Have just installed Windows Phone 7 CTP (Visual Studio 2010 Express) When I deploy the emulator loads but the deployment crashes with the following error. Can anyone help please? Microsoft Visual Studio 2010 Express for Windows Phone Unable to start program '\Windows\taskhost.exe'. The drive cannot locate a specific area or track on the disk.

  Read the article

• Possible to migrate from non-RAID to RAID 1 and then RAID 5?

  - by stueng

  Using software RAID only Is it possible to start with a 2TB disk full of data and safely add it to a RAID 1 array? Is it then possible to add a third disk and migrate the RAID 1 array into a RAID 5 array? OR Is it possible to start with a 2 disk degraded RAID 5 array and then add the third disk later to create a health RAID 5 array? Backstory: I wish to migrate from a 2 disk NAS (RAID 1) to a 3 disk NAS and only purchase one new disk in doing so

  Read the article

• Emulate disk IO speeds in Android SDK

  - by Ben L.

  I don't have a physical Android device to work with, so all I can use is the emulator. I'm wondering if there's something I could use to make the IO speeds more realistic - How do I slow down disk access to the speed it would be on a physical device? Also, this may be unrelated, but when I change the speed and latency options in Eclipse ADT DDMS view, I don't notice any change in internet speed on the emulator. Is this a bug?

  Read the article

• Pen Drive Control

  - by bhaskaragr29

  I want to control television through pen drive. What should I do with pen drive means at hardware and software level? What type of kernel should I load and how I load the kernel and bootloader in pen driver?

  Read the article

• Removing vg and lv after physical drive has been removed

  - by Rene

  We had a disk fail and replace but forgot to vgreduce first. The drive was on it's own VG and with two empty LV's and these are now causing LVM to complain every time any command is run, i.e. # lvscan /dev/vg04/swap: read failed after 0 of 4096 at 4294901760: Input/output error /dev/vg04/swap: read failed after 0 of 4096 at 4294959104: Input/output error /dev/vg04/swap: read failed after 0 of 4096 at 0: Input/output error /dev/vg04/swap: read failed after 0 of 4096 at 4096: Input/output error /dev/vg04/vz: read failed after 0 of 4096 at 995903864832: Input/output error /dev/vg04/vz: read failed after 0 of 4096 at 995903922176: Input/output error /dev/vg04/vz: read failed after 0 of 4096 at 0: Input/output error /dev/vg04/vz: read failed after 0 of 4096 at 4096: Input/output error The two LV's are not important, I just want to stop this error from displaying.

  Read the article

• replacement drive cage for power edge R710

  - by bumble_bee_tuna

  Hi I'm performance tuning a DB server its a Dell R710 there is a very significant I/O bottleneck. Unfortunately the server was purchased with the 6 x 3.5 inch sata configuration which doesn't give me the leeway I need to address the issue. Before going to DAS does anyone know if it is possible to purchase a replacement front drive enclosure ? I know the server is configurable with something like 12 or 16 2.5 inch drives and it appears to be modular ? I tired contacting dell but the offshore parts department reps are not very bright lol. Thanks.

  Read the article

• Download folders from dev server to local drive

  - by Niall Collins

  I am developing a .net web application on a local environment. I have a dev server that the application is installed on. Within the web application on the dev server I have four folders that I dont have locally and that are controlled by another application. In my day to day development I require the four folders on local PC. I would like to automate the process of pulling the folders from the dev server to my local drive, so I can keep thing in sync. Ideally something like this Run file from main folder (be it a bat file, powershell, some sort of job, open to recommendations) Download 4 folders supplied to it. First download bring everything down, from them on only pull the changes Not sure where to start with achieving this but would appreciate any help would with. I know there are apps out there that do something like this but would like to give a go writing something to do this before I resort to using one of them.

  Read the article

• CA ArcServe r11.1 - have to switch Tape Drive Offline then Online to finish backup

  - by Richard

  Ill keep it brief, I have an HP Ultrium 1 in a server currently running CA ArcServe r11.1. I have 5 daily backup tapes, each of which are new. 3 of the 5 work fine without intervention but 2 of them stop at varying points through the backup asking for a new tape, even though that tape is not full. The way I have found around this is to switch the tape drive offline for 10 minutes then switch it back online, whilst the backup is still running. Has anyone ever seen this before? If so, any ideas how to permanently fix this. If all else fails just some pointers in the right direction. Thanks

  Read the article

• 4TB HGST SATA drive only shows 1.62 TB in Windows Server 2012

  - by user136085

  I'm using a Supermicro X9SRE-3F motherboard with the latest BIOS and 2x 4TB drives connected to the on-board SATA controller. If I set the BIOS to RAID and create a RAID 1 array, the array shows up in the BIOS as 3.6TB. However when I boot Windows (on a separate RAID 1 array), the 4TB drives show up individually in disk manager as 2x 1.62TB drives. I could use Windows 2012 to set up software RAID 1, but when I set the BIOS back to 2x individual drives, they still show up in Windows as 2x 1.62TB drives. How do I access the full capacity of these drives? Thanks, Brian Bulaw

  Read the article

• Writing direct to disk with php

  - by Jurander

  I would like to create an upload script that doesn't fall under the php upload limit. There might be an occasion where I need to upload a 2GB, or larger file and I don't want to have to change the whole server execution to above 32MB. Is there a way to write direct to disk from php? What method might you propose someone would use to accomplish this? I have read around stack overflow but haven't quite found what I am looking to do.

  Read the article

• Permissionless external drive with NTFS

  - by user12889

  I have an external hard disk which has 1 partition, formatted in NTFS. I use this drive on multiple computers with a different logins on different machines, Windows XP and Windows 7. All files are plain old files, not OS encrypted or compressed. Every now and then Windows 7 does not let me access some files, citing permission problems. I can circumvent this per case by taking ownership and setting appropriate permissions. This, however, is tedious. Is there a simple way to tell Windows to not enforce or store any permissions on any file/directory on a partition?

  Read the article

• Motherboard rejects identical hard drive, one works the other doesn't

  - by Payson Welch

  I have an interesting situation. I have a Dell XS23-SB server that has four blades in it. The blades use Supermicro X7DWT motherboards, and interface with the sata drives through a backplane. I took two identical drives from a raid 0 enclosure that came from the factory (GDrive), one works on all four servers, the other does not. I verified that they both work by plugging them into a hard drive cradle. This behavior can be repeated with other drives, some drives work and some don't. However when i test them, they ALL work on my PC. What could cause this?

  Read the article

• Can't access files on external drive after reformatting Macbook Pro

  - by Peter Wells

  I recently had to reformat my Macbook Pro, and imported my account and settings from Time Machine via the Migration Assistant. Everything on the Mac itself is fine, but now I don't have permission to access almost everything on my external drive. A number of folders have the little red 'no access' sign on them and I can't rename or move anything. Looking at the info for these files, it appears that access rights were attached only to my old user account. Is there some way to reassign these files and folders to my new user account? Thanks.

  Read the article

• Using Pisa to write a pdf to disk

  - by phoebebright

  I have pisa producing .pdfs in django in the browser fine, but what if I want to automatically write the file to disk? What I want to do is to be able to generate a .pdf version file at specified points in time and save it in a uploads directory, so there is no browser interaction. Is this possible?

  Read the article

• Mapping skydrive as network drive in macos

  - by vittore

  as you probably know, if you have windows live account you can use free skydrive 25 gb storage. Even more a lot of people know that if you go to your skydrive in browser and copy cid query parameter value (https://...live.com/...&cid=xxxxxxxx ) you will be able to map skydrive as network drive in windows using this network pass \[cid].docs.live.net[cid]\ I do now that if you have network share like \server\folder i can map it in macos too, as smb://server/folder. however it is doesn't seem to be a case with skydrive when i try to map it as smb://[cid].docs.live.net/[cid] finder tells it can't connect. Anyone know how to map it ?

  Read the article

• scp vs netatalk, samba, and/or vsftpd with External USB drive

  - by KitsuneYMG

  I set up a ubuntu server machine to share an ext2 formatted external usb drive. When attempting to copy a single 275MB files from said device through netatalk, I get estimated download rates at around 45 min. With samba and ftp (using vsftpd) I get 1+ hours! Using scp to copy the file results in complete download within 5 minutes. Another option, ssh+cp from external device to ~ and then using netatalk to grab it from there results in a total time of arounf 7 minutes. Does anyone have a clue what is misconfigured? Assuming that nothing is, is there any fs/pseudo-fs that would use the internal hdd as an intermediate location/onion-layer for the external hdd (for reads only)? Details: AppleVolumes.default: /mnt/ext USB allow:username cnidscheme:cdb options:usedots,upriv

  Read the article

< Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >