Search Results

Search found 4349 results on 174 pages for 'remember me'.

Page 144/174 | < Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >

• Can't manage iPod from linux anymore

  - by kemp

  I used to be able to see and manage my iPod with different softwares: Amarok, Rhythmbox, GTKPod. The device is a nano 1st generation 4gb. Currently it mounts regularly and can be accessed from the file system, but I get this in dmesg: [ 1547.617891] scsi 11:0:0:0: Direct-Access Apple iPod 1.62 PQ: 0 ANSI: 0 [ 1547.619103] sd 11:0:0:0: Attached scsi generic sg2 type 0 [ 1547.620478] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.620494] sd 11:0:0:0: [sdb] 7999487 512-byte hardware sectors: (4.09 GB/3.81 GiB) [ 1547.621718] sd 11:0:0:0: [sdb] Write Protect is off [ 1547.621726] sd 11:0:0:0: [sdb] Mode Sense: 68 00 00 08 [ 1547.621732] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.623591] sd 11:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 [ 1547.624993] sd 11:0:0:0: [sdb] Assuming drive cache: write through [ 1547.625003] sdb: sdb1 sdb2 [ 1547.629686] sd 11:0:0:0: [sdb] Attached SCSI removable disk [ 1548.084026] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.369502] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.504358] FAT: invalid media value (0x2f) [ 1548.504363] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1548.945173] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! [ 1548.945179] FAT: invalid media value (0x2f) [ 1548.945182] VFS: Can't find a valid FAT filesystem on dev sdb1. [ 1610.092886] usb 2-6: USB disconnect, address 9 The only application that can access it (partially) is Rhythmbox. I say partially because I can transfer files to the iPod but can't remove or modify them. Also one transfer didn't finish and only 9 out of 16 songs were delivered to the device. All other softwares I tried (GTKPod, Amarok, Songbird) don't even detect it. What can I do to troubleshoot this? EDIT: # fdisk -l /dev/sdb Disk /dev/sdb: 4095 MB, 4095737344 bytes 241 heads, 62 sectors/track, 535 cylinders Units = cylinders of 14942 * 512 = 7650304 bytes Disk identifier: 0x20202020 Device Boot Start End Blocks Id System /dev/sdb1 1 11 80293+ 0 Empty Partition 1 has different physical/logical beginnings (non-Linux?): phys=(0, 1, 1) logical=(0, 1, 2) Partition 1 has different physical/logical endings: phys=(9, 254, 63) logical=(10, 181, 8) Partition 1 does not end on cylinder boundary. /dev/sdb2 11 536 3919415+ b W95 FAT32 Partition 2 has different physical/logical beginnings (non-Linux?): phys=(10, 0, 7) logical=(10, 181, 15) Partition 2 has different physical/logical endings: phys=(497, 240, 62) logical=(535, 88, 61) EDIT2: The "before" state is hard to tell, it was a lot of updates ago. Haven't been using my iPod for a while so I can't say when exactly it stopped working. I'm sure Amarok was still at version 1.X but can't remember when it was. My current system is debian testing fully updated. NOTE: just noticed that if I mount the device manually instead of letting nautilus automount it, I can see it again on GTKPod but still not on Banshee AND it's vanished from Rhythmbox...

  Read the article

• D-Link DIR-300 slows down / loses network

  - by basic6

  Hi there, there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

  Read the article

• Downloading Python 2.5.4 (from official website) in order to install it

  - by brilliant

  I was quite hesitant about whether I should post this question here on "StackOverflow" or on "SuperUser", but finally decided to post it here as Python is more a programming language rather than a piece of software. I've been recently using Python 2.5.4 that is installed on my computer, but at the moment I am not at home (and won't be for about two weeks from now), so I need to install the same version of Python on another computer. This computer has Windows XP installed – just like the one that I have at home. The reason why I need Python 2.5.4 is because I am using “Google App Engine”, and I was told that it only supports Python 2.5 However, when I went to the official Python page for the download, I discovered that certain things have changed, and I don’t quite remember where exactly from that site I had downloaded Python 2.5.4 on my computer at home. I found this page: http://www.python.org/download/releases/2.5.4/ Here is how it looks: (If you can’t see it here, please check it out at this address: http://brad.cwahi.net/some_pictures/python_page.jpg ) A few things here are not clear to me. It says: For x86 processors: python-2.5.4.msi For Win64-Itanium users: python-2.5.4.ia64.msi For Win64-AMD64 users: python-2.5.4.amd64.msi First of all, I don’t know what processor I am using – whether mine is “x86” or not; and also, I don’t know whether I am an “Win64-Itanium” or an “Win64-AMD64” user. Are Itanium and AMD64 also processors? Later it says: Windows XP and later already have MSI; many older machines will already have MSI installed. I guess, it is my case, but then I am totally puzzled as to which link I should click as it seems now that I don’t need those three previous links (as MSI is already installed on Windows XP), but there is no fourth link provided for those who use “Windows XP” or older machines. Of course, there are these words after that: Windows users may also be interested in Mark Hammond's win32all package, available from Sourceforge. but it seems to me that it is something additional rather than the main file. So, my question is simple: Where in the official Python website I can download Python 2.5.4, precisely, which link I should click?

  Read the article

• KeePass justification

  - by Jeff Walker

  I work at a place that tries to take security seriously, but sadly, they often fail. Currently, one of the major ways they fail is password management. I personally have about 20 accounts (my personal user id on lots of machines). For shared "system" accounts, there are about 45 per environment; development, test, and production. I have access to 2 of those, so my personal total is somewhere around 115 accounts. Passwords have to be at least 15 characters with some extensive but standard complexity constraints, and have to be changed every 60 days or so (system accounts every year). They also should not be the same for different accounts, but that isn't enforced. Think DoD-type standards. There is no way to remember and keep up with this. It just isn't humanly possible, as far as I'm concerned. This might be a good justification of a centralized account management system, a la LDAP or ActiveDirectory, but that is a totally different battle. Currently the solution is an Excel spreadsheet. They use Excel to put a password on it, and then most people make a copy and remove the password. This makes my stomach turn. I use KeePass for this problem and it manages all of my account very well. I like the features like auto-typing, grouping, plugins, password generation, etc. It uses AES-256 encryption via the .Net framework, and while not FIPS compliant, it has a very good reputation. The only problem is that they are also very careful about using randomly downloaded software. So we have to justify every piece of software on our workstations. I have been told that they really don't want me to use this, be cause of the "sensitive nature" of storing passwords. sigh My justification has to be "VERY VERY strong". I have been tasked with writing a justification for KeePass, but as I am lazy, I would like any input that I can get from the community. What do you recommend? Is there something out there that is better or more respected than KeePass? Is there any security experts saying interesting things on this topic? Anything will help at this point. Thanks.

  Read the article

• Detach current session and attach to another session, done with one script, can I?

  - by Jimm Chen

  After reading the vague official doc of GNU screen( http://www.gnu.org/software/screen/manual/screen.html ) and asking quite some questions at this site. I still cannot figure out how to accomplish such a task with a shell script. This task costs some words to describe. Assume I'm using PuTTY to telnet into my Linux server. ?STEP 1? Launch 2 telnet connections . From putty window 1 (PTWIN1),telnet into Linux Bash shell, execute screen -RR to launch a screen session, and get session name 21385.pts-4.linux-ic37 . From putty window 2 (PTWIN2), do that same as in PTWIN1, but this time, I get session name 22041.pts-9.linux-ic37 . Now, we have two screen sessions running simultaneously. We can check this: $ screen -ls There are screens on: 22041.pts-9.linux-ic37 (Attached) 21385.pts-4.linux-ic37 (Attached) 2 Sockets in /var/run/uscreens/S-chj2. ?STEP 2? Assume that for some reason, PTWIN1's TCP connection is lost abnormally(but server doesn't know that), and an urgent work is pending on session 21385 and I want to quickly regain control of it. Fortunately, we know the 21385 session is still there, so, I want to have PTWIN2 attach to session 21385. Because I hate to remember the esoteric screen option all the time, so I decide to write a script called sttach. I hope that sttach 21385.pts-4.linux-ic37 can let me attach to session 21385(for PTWIN2). Now, let's say sttach works well and I take control of 21385 on PTWIN2. ?STEP 3? Some minutes later. I want to go back to work on session 22041. Here, please allow me to have PTWIN2 remain associated with session 21385. What I would like to do is to launch another putty window (PTWIN3), telnet into server, and execute sttach 22041.pts-9.linux-ic37 in hope that I can resume session 22041 on PTWIN3 . You can see the benefit of sttach: as long as I know the target session name, I can call it to have my PuTTY window switch to that session, regardless whether the target session is "(Attached)" or "(Detached)", and regardless whether the running context is inside a screen session or not. Now the question: How to write the (Bash) script sttach? I mean, run screen with appropriate options in sttach to accomplish the goal. Waiting for your kind answer. Thank you. My previous questions regarding GNU screen: GNU screen, how to get current sessionname programmatically Is it possible to change GNU screen session name after created? How do I know I'm running inside a linux "screen" or not? My env: openSUSE Linux 11.3, GNU screen 4.00.03 (FAU) 23-Oct-06

  Read the article

• My server freezes within a few hours of logging out. Staying logged in keeps the server running

  - by HappyEngineer

  I have an Ubuntu Godaddy server I use to host mail and webapps. It started having problems a couple months ago. It would lock up and stop responding to anything. I couldn't ssh into it, so I'd have godaddy power cycle the server. I have never seen anything that looked suspicious in the var logs (although I'm no expert at reading them). An fsck turned up no problems. Godaddy replaced the ram, but found no hardware problems. I started logging the output from "top" to a log file and found that even that stops running when the server freezes. Now, here is the crazy part: It got so bad that it would actually go down every few hours, but then it stopped going down. I eventually realized I had left an ssh terminal logged into the machine running top. This seemed unlikely to be a reason, but after the server was up with no problems for a full week (remember, it had been going down after just a few hours), I disconnected from the ssh session. Lo and behold, within a few hours the server froze again! I had them power cycle again and then left another ssh session open with top. It has been going without problems for 8 days now. I told others about this and they hardly believe me. I simply can't imagine what is going on. I don't know what else to try other than to just get a new server and reinstall everything. Does anyone have any ideas about what I can look for to determine what the cause is? Is it possible there's some sort of exploit on the server which only runs if everyone is logged out of the system? EDIT: The power management gone haywire sounds plausible, so I've modified the /boot/grub/menu.lst to boot with acpi=off and apm=off. It appears to have prevented kacpid and kacpid_notify from being in the process list, so I assume I did that right. I've disconnected all my sessions from the server. I'll check later tonight to see if it's still up. If it goes down then I'll try the pinging process idea. EDIT: It went down again. It lasted about a day. I've had them reboot, so now I'll try running "nohup ping -i 5 google.com &" and then disconnect. If it goes down again I'll come back. Hopefully someone will have some more ideas.

  Read the article

• Root directory permissions on Mac OS X 10.6?

  - by Agos

  Hi, I was wondering if it's normal that the root directory / should be owned by “root”. I get asked for my password every time I want to do something there (e.g. save a file, create a directory) and I don't remember this happening before (though this may just be my faulty memory). Here's the relevant terminal output: MacBook:~ ago$ ls -lah / total 37311 drwxr-xr-x@ 35 root staff 1,2K 22 Mar 12:34 . drwxr-xr-x@ 35 root staff 1,2K 22 Mar 12:34 .. -rw-rw-r--@ 1 root admin 21K 22 Mar 10:21 .DS_Store drwx------ 3 root admin 102B 28 Feb 2008 .Spotlight-V100 d-wx-wx-wt 2 root admin 68B 31 Ago 2009 .Trashes -rw-r--r--@ 1 ago 501 45K 23 Gen 2008 .VolumeIcon.icns srwxrwxrwx 1 root staff 0B 22 Mar 12:34 .dbfseventsd ---------- 1 root admin 0B 23 Giu 2009 .file drwx------ 27 root admin 918B 22 Mar 10:55 .fseventsd -rw-r--r--@ 1 ago admin 59B 30 Ott 2007 .hidden -rw------- 1 root wheel 320K 30 Nov 11:42 .hotfiles.btree drwxr-xr-x@ 2 root wheel 68B 18 Mag 2009 .vol drwxrwxr-x+ 276 root admin 9,2K 19 Mar 18:28 Applications drwxrwxr-x@ 21 root admin 714B 14 Nov 12:01 Developer drwxrwxr-t+ 74 root admin 2,5K 18 Dic 22:14 Library drwxr-xr-x@ 2 root wheel 68B 23 Giu 2009 Network drwxr-xr-x 4 root wheel 136B 13 Nov 17:49 System drwxr-xr-x 6 root admin 204B 31 Ago 2009 Users drwxrwxrwt@ 4 root admin 136B 22 Mar 12:35 Volumes drwxr-xr-x@ 39 root wheel 1,3K 13 Nov 17:44 bin drwxrwxr-t@ 2 root admin 68B 23 Giu 2009 cores dr-xr-xr-x 3 root wheel 5,1K 17 Mar 11:29 dev lrwxr-xr-x@ 1 root wheel 11B 31 Ago 2009 etc -> private/etc dr-xr-xr-x 2 root wheel 1B 17 Mar 11:30 home drwxrwxrwt@ 3 root wheel 102B 31 Ago 2009 lost+found -rw-r--r--@ 1 root wheel 18M 3 Nov 19:40 mach_kernel dr-xr-xr-x 2 root wheel 1B 17 Mar 11:30 net drwxr-xr-x@ 3 root admin 102B 24 Nov 2007 opt drwxr-xr-x@ 6 root wheel 204B 31 Ago 2009 private drwxr-xr-x@ 64 root wheel 2,1K 13 Nov 17:44 sbin lrwxr-xr-x@ 1 root wheel 11B 31 Ago 2009 tmp -> private/tmp drwxr-xr-x@ 17 root wheel 578B 12 Set 2009 usr lrwxr-xr-x@ 1 root wheel 11B 31 Ago 2009 var -> private/var Are these ownerships / permissions ok? Should I chmod/chown something? Thanks in advance

  Read the article

• How can I centralise MySQL data between 3 or more geographically separate servers?

  - by Andy Castles

  To explain the background to the question: We have a home-grown PHP application (for running online language-learning courses) running on a Linux server and using MySQL on localhost for saving user data (e.g. results of tests taken, marks of submitted work, time spent on different pages in the courses, etc). As we have students from different geographic locations we currently have 3 virtual servers hosted close to those locations (Spain, UK and Hong Kong) and users are added to the server closest to them (they access via different URLs, e.g. europe.domain.com, uk.domain.com and asia.domain.com). This works but is an administrative nightmare as we have to remember which server a particular user is on, and users can only connect to one server. We would like to somehow centralise the information so that all users are visible on any of the servers and users could connect to any of the 3 servers. The question is, what method should we use to implement this. It must be an issue that that lots of people have encountered but I haven't found anything conclusive after a fair bit of Googling around. The closest I have seen to solutions are: something like master-master replication, but I have read so many posts suggesting that this is not a good idea as things like auto_increment fields can break. circular replication, this sounded perfect but to quote from O'Reilly's High Performance MySQL, "In general, rings are brittle and best avoided" We're not against rewriting code in the application to make it work with whatever solution is required but I am not sure if replication is the correct thing to use. Thanks, Andy P.S. I should add that we experimented with writes to a central database and then using reads from a local database but the response time between the different servers for writing was pretty bad and it's also important that written data is available immediately for reading so if replication is too slow this could cause out-of-date data to be returned. Edit: I have been thinking about writing my own rudimentary replication script which would involve something like having each user given a server ID to say which is his "home server", e.g. users in asia would be marked as having the Hong Kong server as their own server. Then the replication scripts (which would be a PHP script set to run as a cron job reasonably frequently, e.g. every 15 minutes or so) would run independently on each of the servers in the system. They would go through the database and distribute any information about users with the "home server" set to the server that the script is running on to all of the other databases in the system. They would also need to suck new information which has been added to any of the other databases on the system where the "home server" flag is the server where the script is running. I would need to work out the details and build in the logic to deal with conflicts but I think it would be possible, however I wanted to make sure that there is not a correct solution for this already out there as it seems like it must be a problem that many people have already come across.

  Read the article

• Does VMware_ThinApp_4.0.3_169725.msi contain Trojan.Win32.Vapsup in it? [closed]

  - by Joe

  Today I ran a full system scan using Online Armor++. It detected Trojans in the installer. I have had this installer on the computer for many months and I do not remember if I ever installed it on this PC or not. For some reason I unpacked the installer with 7zip though. I was probably going to attempt to make it portable. Anyway so I had the installer in a folder, and another folder next to it with all of the installers files unpacked. The VMwareVS.cab file that was extracted from the installer, also had its files extracted into another folder. This was all done many months ago. OA++ did not detect the installer itself as as Trojan VMwareVS.cab, but it did detect 4 of the files that I had unpacked as Trojans. Here are the details of what the scan detected on my PC today. Note: I uploaded these files to VirusTotal....the Ikarus and A-squared engines(the engines from Online Armor++) are not detecting anything. But some of the other engines are detecting the same Trojan that OA++ detected(Trojan.Win32.Vapsup). C:\Downloads\VMware_ThinApp_4.0.3_169725.msi [This file was not detected by the Virus Scan as infected] CRC-32: 50189335 MD5: 9e32e3272d2637fb6e0759a604879e6f SHA-1: 19ef5a6d586ddcc5b9222ba57b0f14159655f3f8 C:\Downloads\VMware_ThinApp_4.0.3_169725\VMwareVS.cab [This file was not detected by the Virus Scan as infected] CRC-32: d3a9694a MD5: ddc278a8fe0a25486277d9800e6af85a SHA-1: 456b731c8b6fdb7a1d7bcff3d1fbe9df58ccc73a Online Armor++ Virus Scan Results: Detected Trojan.Win32.Vapsup.vee!A2 C:\Downloads\VMware_ThinApp_4.0.3_169725\Binary.ThinstallProcess CRC-32: 4888b13c MD5: 4884cb4622278c0835b9a5dcd2ae0473 SHA-1: ed879ae65147805dd69e1355c17df814b9d434ce Detected Trojan.Win32.Vapsup.vef!A2 C:\Downloads\VMware_ThinApp_4.0.3_169725\VMwareVS\AppSync.exe CRC-32: fd20b378 MD5: cbdcdd590f7ffc52b6ce68fa11f2bda4 SHA-1: aebf685e02d6693df9eaa92c67dc5746792b5ecf Detected Trojan.Win32.Vapsup.veg!A2 C:\Downloads\VMware_ThinApp_4.0.3_169725\VMwareVS\logging.dll CRC-32: 8adee5d5 MD5: 56ff9b83f58ba8eacb6e939aa4759bf0 SHA-1: b52fa38765a25fe6a2c4f60d76545a4dd64904eb Detected Trojan.Win32.Vapsup.vek!A2 C:\Downloads\VMware_ThinApp_4.0.3_169725\VMwareVS\thinreg.exe CRC-32: 423c5652 MD5: c436feff8d9096e7475c84a6bca6096c SHA-1: 685b84af796132ce144aacd6ff23379e17ddf1a7 Are these files indeed infected by this Trojan, or is it just a false positive? Does anybody have the same version of the original installer, who could find out if the Checksums of the installer and unpacked files match? Should I be worried about whether this Trojan has spread and infected my machine? Thanks in advance for any help!

  Read the article

• Windows 7 laptop constantly dropping internet connection

  - by Corbin Holbert

  I have scoured the web for an answer and failed to find one. I am using a Toshiba Satellite laptop running Windows 7 64-Bit. I have the computer connected via Wifi. Now, I am no beginner with the Internet, or anything related to computers, as I have grown up teaching everyone around me how to use computers, and went to college for IT. Everything on my network works flawlessly at all times, except for this evil laptop. The worst part is that I fixed this once before a few years back and recently had to replace the hard drive and re-install the OS, but cannot for the life of me remember what I did to make this problem go away. I am in my browser, connected to the Internet. I click a link. Suddenly no internet access. All I do is click down on the WiFi connection in the task bar, disconnect and reconnect immediately. Internet is back the moment I hit "connect." I have read many people had the same issues as I am having, but they all had triggers or other network issues. I have no trigger (this happens literally five to six times per minute no matter what I am doing) and I have no problems with my router, modem, or any other devices or computers on said network. As I am a web designer, and like to test my work live at every turn- this is going to result in this laptop being in pieces if I can't get it fixed soon. If more info is needed, let me know and I will provide. Thanks for any help offered! EDIT: Network Card: Realtek RTL8188CE Wireless LAN 802.11n PCI-E NIC Network state reads as "No Internet Access" when the problem first occurs, then magically I have Internet access for about ten seconds once I disconnect and reconnect. I have turned off IPV6, I have turned off power saving options for the network adapter, no viruses. Any new ideas? Also, I had to disconnect and reconnect four times just to get to this edit screen- and will likely have to do the same just to post it- it's that bad.

  Read the article

• Internet connection sharing between Windows XP and Windows 7

  - by Dave

  I bought my lil sister's netbooks for Christmas and I've been having a heck of a time trying to get Internet Connection Sharing to work. The host computer is a Windows XP box and it uses a US Cellular 3G modem dongle thingy to set it's Internet access. Additionally I have a hard wire plugged into the LAN1 port of the router described below. (I tried the WAN port out of desperation but things didn't seem happy that way.) Additionally they have a linksys router (can't remember specific model number, I will find this out) that I was using to take advantage of it's wireless capabilities. Originally thought about updating the router to use dd-wrt, but after reading the instructions it looked like to much of a pita (had to downgrade firmware, then install dd-wrt) to set up, eventually I caved, out of desperation, and ended up successfully installing dd-wrt on the router. I have DHCP turned off on the router, actually all I could select was DHCP forwarder. The netbooks both have windows 7 starter installed on them. Initially, I had the networks joined to a homegroup but I dropped that and everyone is able to see everyone in their respective network explorers. When I turn on Internet Connection Sharing on the host, its IP on the LAN changed to 192.168.0.1, so I arbitrarily decided to assign the router to port 192.168.0.100. When I connect the netbooks they get IPs dynamically. As I stated before, everyone can see everyone in the network explorer, and shares can be accessed. The weird thing is that everyone can ping the router but they cannot ping each others IPs. The status on the netbooks says that there is no Internet Connectivity. Another thing I tried was manually setting the DNS servers on the netbooks to the DNS servers that the host computer has. The funny thing is when I ping an outside domain such as google.com the IP address resolves, however I get no responses from the pings. When I tried plugging the host into the WAN port I could ping the router, nor could I access the router's web access admin. Another thing I tried was turning off the firewall on the netbooks and the firewall off on the host computer for the LAN connection, and they still could not ping each other. Also I thought I should be able to start a remote desktop connection but I couldn't do that either, I also checked to make sure that computers would in fact accept a request for remote desktop connections.

  Read the article

• mysql: job failded to start. mysqld.sock is missing

  - by Freefri

  How can I fix this and start mysql-server? After /etc/init.d/mysql start or service mysql start I get the message start: "Job failed to start" And after # mysqld I get this: mysqld 121123 11:33:33 [ERROR] Can't find messagefile '/usr/share/mysql/errmsg.sys' 121123 11:33:33 [Note] Plugin 'FEDERATED' is disabled. mysqld: Unknown error 1146 121123 11:33:33 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 121123 11:33:33 InnoDB: The InnoDB memory heap is disabled 121123 11:33:33 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121123 11:33:33 InnoDB: Compressed tables use zlib 1.2.3.4 121123 11:33:33 InnoDB: Initializing buffer pool, size = 128.0M 121123 11:33:33 InnoDB: Completed initialization of buffer pool 121123 11:33:33 InnoDB: highest supported file format is Barracuda. 121123 11:33:33 InnoDB: Waiting for the background threads to start 121123 11:33:34 InnoDB: 1.1.8 started; log sequence number 1595675 121123 11:33:34 [ERROR] Aborting 121123 11:33:34 InnoDB: Starting shutdown... 121123 11:33:35 InnoDB: Shutdown completed; log sequence number 1595675 121123 11:33:35 [Note] I try to do what mysql say me to do: mysql_upgrade Looking for 'mysql' as: mysql Looking for 'mysqlcheck' as: mysqlcheck Running 'mysqlcheck' with connection arguments: '--port=3306' '--socket=/var/run/mysqld/mysqld.sock' mysqlcheck: Got error: 2002: Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) when trying to connect FATAL ERROR: Upgrade failed And yes, /var/run/mysql is empty: mysql_upgrade Looking for 'mysql' as: mysql Looking for 'mysqlcheck' as: mysqlcheck Running 'mysqlcheck' with connection arguments: '--port=3306' '--socket=/var/run/mysqld/mysqld.sock' mysqlcheck: Got error: 2002: Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) when trying to connect FATAL ERROR: Upgrade failed And this is my file /etc/mysql/my.cnf # cat /etc/mysql/my.cnf |grep sock # Remember to edit /etc/mysql/debian.cnf when changing the socket location. socket = /var/run/mysqld/mysqld.sock socket = /var/run/mysqld/mysqld.sock socket = /var/run/mysqld/mysqld.sock Then I try to reinstall mysql from cero: apt-get purge mysql-client mysql-common mysql-server rm -R /var/lib/mysql rm -R /etc/mysql rm -R /var/run/mysqld userdel mysql apt-get install mysql-server mysql-client Then, after typing my root password for mysql I get this error: | Unable to set password for the MySQL "root" user ¦ ¦ ¦ ¦ An error occurred while setting the password for the MySQL administrative ¦ ¦ user. This may have happened because the account already has a password, or ¦ ¦ because of a communication problem with the MySQL server. ¦ ¦ ¦ ¦ You should check the account's password after the package installation. ¦ ¦ ¦ ¦ Please read the /usr/share/doc/mysql-server-5.5/README.Debian file for more ¦ ¦ information. And again I can't start mysql getting the same messages.

  Read the article

• Windows 7 The boot selection failed because a required device is inaccessible 0xc000000f

  - by piratejackus

  I have a problem with my Windows 7, hardware : Acer 3820TG Operating Systems : Windows 7 and Ubuntu 10.04 dual Case: When I try to boot my windows 7 I see an error: "Window failed to start. A recent hardware or software change might be the cause. To fix the problem: 1.Insert.... 2. .... ... status : 0xc000000f info : The boot selection failed because a required device is inaccessible .... " I can't exactly remember what were my last actions on Windows. I already searched this error and applied the proposed solutions, I created a repair USB (because I don't have a CD-ROM nor a Windows 7 CD) such as; -repair operating system :it says it cannot repair it -checking disk (chkdsk D: /f /r) : it checks the disk without a problem or error and it takes pretty long (more than a hour). But when I restart, still the same error. -I didn't create a restore point so I pass this option -I don't have a system image -I tried to run windows recovery (I have a recovery partition) but there are just two options: 1- Format the operating system but retain user data (copies the files under users to c\backup folder, but when I searched deeper I found that there are some people who already tried this option and couldn't find their user files under backup directory). Plus, I have unfortunately just one partition D (it is a fault I know) because I use always Ubuntu. So this is not applicable in my situation 2- Format entire system (Windows). I keep my valuable data in windows but not in user folder. I was reaching them from Windows. -I tried to repair windows boot by: bootrec /fixMBR bootrec /fixBoot bootrec /rebuildBCD I lost all grub menu, and reinstalled it. - ubuntuforums.org/showthread.php?t=1014708&page=29 nothing changed, same error. I created a thread in microsoft forums - http://social.answers.microsoft.com/Forums/en-US/w7install/thread/69517faf-850a-45fd- 8195-6d4ed831f805 but I couldn't find a solution. Before I run chkdsk from usb repair disk I couldn't able to mount Windows (NTFS) partition from Ubuntu, I was getting "couldn't mount file system, error code 2". I tried to fix ntfs partition from ubuntu and got "segmentation fault". I also created a thread on ubuntuforums for this mount problem: - http://ubuntuforums.org/showthread.php?t=1606427 So, after chkdsk, I could enable to mount windows partition but all I see in this partition is chkdsk logs, no any other data. Now, I don't think I lost my data because I don't get any filesystem errors, just the boot section, but this log files under windows partition makes me afraid. I see that Microsoft developers don't have a solution yet for this error. If you need any information to get more idea I can give, maybe I miss some points or it could be complicated. Thanks in advance.

  Read the article

• My computer's dying :(

  - by j-t-s

  Hi All I have a sweet computer and have never had any real problems with it until now. I recently formatted my computer and all was well. But now my monitor randomly flickers. The monitor will just go black for about a second or two, then it'll return back to its normal state with all the stuff still on the screen. This is getting progressively worse. Another problem that has started is my computer randomly restarts. (I've managed to prevent it from restarting by removing the check in Automatically Restart from the Startup and Recovery Dialog. But I know this doesn't solve the problem). It also completely freezes up on me. One last thing, this morning I got a big blue screen. I can't remember what it said, but if it happens again I will take note of it and repost. Or if I can find some kind of a log file containing that bluescreen error I will post. I have checked all cords, and they're all fine. Nothing's loose. My computer isn't overheating either. I've taken the case off for 3 whole days and haven't used the computer for those 3 days, which has had no effect. I've checked the connections inside and nothing's loose there either. I know there's nothing wrong with my monitor because my friend has 2 computers and it works perfectly on those computers. I don't understand how my computer could suddenly become so unstable. I'm almost certain that I have no viruses; I full-scan my pc everyday for nastys, and have strict firewall settings. Anyway, I don't see how it could be a virus anyway simply due to the fact that I had these problems right after I formatted, and before I even had the chance to install or copy anything or even connect to the internet. I know it has nothing to do with the way I formatted the computer too, I've been fixing computers for years. Sorry for rambling on, just making sure I don't leave anything out. Has anybody else had this problem? Can somebody please try to help me with this? Thank you :)

  Read the article

• how to diagnosis and resolve: /usr/lib64/libz.so.1: no version information available

  - by matchew

  I had a hell of a time installing lxml for python2.7 on centOs5.6. For some background, python2.7 is an alternative installation of python on centOS5.6 which comes with python2.4 installed. it was bulit from source per its instrucitons ./configure make make altinstall However, after about 20 hours of trying I managed to find a workable solution and was able to install lxml. Until, I notice the following error at the top of the interpreter: python2.7: /usr/lib64/libz.so.1: no version information available (required by python2.7) Python 2.7.2 (default, Jun 30 2011, 18:55:26) [GCC 4.1.2 20080704 (Red Hat 4.1.2-50)] on linux2 Type "help", "copyright", "credits" or "license" for more information. >>> print 'Sheeeeut!' this error is printed out everytime I run a script. For example: $ ./test.py /usr/local/bin/python2.7: /usr/lib64/libz.so.1: no version information available (required by /usr/local/bin/python2.7) the script runs flawlessly, but this error is bothersome. After some digging I have seem to believe I have a wrong version of libz installed, that it is either an older version or built for a different platform. I'm not quite sure how, I've only installed libz through yum, as far as I know. Although, I can't quite remember every little thing I tried in my twenty hours of trying. You may also be intereted in what my lib64 folder looks like, here is some information $ ls -ltrh libz* -rwxr-xr-x 1 root root 84K Jan 9 2007 libz.so.1.2.3 -rwxr-xr-x 1 root root 107K Jan 9 2007 libz.a -rwxr-xr-x 1 root root 154K Feb 22 23:30 libzdb.so.7.0.2 lrwxrwxrwx 1 root root 13 Apr 20 20:46 libz.so.1 -> libz.so.1.2.3 lrwxrwxrwx 1 root root 15 Jun 30 18:43 libzdb.so.7 -> libzdb.so.7.0.2 lrwxrwxrwx 1 root root 13 Jul 1 11:35 libz.so -> libz.so.1.2.3 lrwxrwxrwx 1 root root 15 Jul 1 11:35 libzdb.so -> libzdb.so.7.0.2 notice: the items that Say Jul 1st or Jun 30th are from me. I had initially moved these files into a backup folder as they seeemed to be 1. duplicates and 2. had a date after/during my problems I alluded to earlier that I had with lxml One inclination is to completely remove python2.7 and re-install. I think having it install to /usr/local/ was a poor default choice. However, without the make uninstall option being present it seems to be a time consuming task for a solution I am not quite sure would solve my problem.

  Read the article

• How should I set up my Hyper-V server and network topology?

  - by Daniel Waechter

  This is my first time setting up either Hyper-V or Windows 2008, so please bear with me. I am setting up a pretty decent server running Windows Server 2008 R2 to be a remote (colocated) Hyper-V host. It will be hosting Linux and Windows VMs, initially for developers to use but eventually also to do some web hosting and other tasks. Currently I have two VMs, one Windows and one Ubuntu Linux, running pretty well, and I plan to clone them for future use. Right now I'm considering the best ways to configure developer and administrator access to the server once it is moved into the colocation facility, and I'm seeking advice on that. My thought is to set up a VPN for access to certain features of the VMs on the server, but I have a few different options for going about this: Connect the server to an existing hardware firewall (an old-ish Netscreen 5-GT) that can create a VPN and map external IPs to the VMs, which will have their own IPs exposed through the virtual interface. One problem with this choice is that I'm the only one trained on the Netscreen, and its interface is a bit baroque, so others may have difficulty maintaining it. Advantage is that I already know how to do it, and I know it will do what I need. Connect the server directly to the network and configure the Windows 2008 firewall to restrict access to the VMs and set up a VPN. I haven't done this before, so it will have a learning curve, but I'm willing to learn if this option is better long-term than the Netscreen. Another advantage is that I won't have to train anyone on the Netscreen interface. Still, I'm not certain if the capabilities of the Windows software firewall as far as creating VPNs, setting up rules for external access to certain ports on the IPs of Hyper-V servers, etc. Will it be sufficient for my needs and easy enough to set up / maintain? Anything else? What are the limitations of my approaches? What are the best practices / what has worked well for you? Remember that I need to set up developer access as well as consumer access to some services. Is a VPN even the right choice?

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter EDIT: I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  EDIT: I thought I pinpointed the problem. Just now I tried to go to the firefox addons page which uses https and gmail also uses https. So I thought I am unable to load https pages on this computer. So I went to a bank site which uses https but that loads just fine. Sigh.... I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• ruby on rails gitorious setup on ubuntu

  - by dogmatic69

  Ive been trying to install gitorious for a while now which required ruby and rails etc. Ive finally got rails pages serving but cant finish the installation of gitorious because the gem version is too new. the error logs say please run 'rake ultrasphinx:configure' and that gives rake ultrasphinx:configure (in /var/www/apps/gitorious) rake aborted! uninitialized constant ActiveSupport::Dependencies::Mutex /var/www/apps/gitorious/Rakefile:10:in `require' (See full trace by running task with --trace) From searching google this is beacuse of the wrong gem verison. Cant find a way to down grade it. apparently sudo gem update --system 1.4.2 should do the trick but ubuntu 10.10 does not like this. ERROR: While executing gem ... (RuntimeError) gem update --system is disabled on Debian, because it will overwrite the content of the rubygems Debian package, and might break your Debian system in subtle ways. The Debian-supported way to update rubygems is through apt-get, using Debian official repositories. If you really know what you are doing, you can still update rubygems by setting the REALLY_GEM_UPDATE_SYSTEM environment variable, but please remember that this is completely unsupported by Debian. So i added export REALLY_GEM_UPDATE_SYSTEM=1 to .bashrc and reloaded it with . ~/.bashrc and still the same. ive tried various forms of setting this environmental variable with no luck. Ive also been told on #gitorious irc channel to add the file config/initializers/rubygems.rb with the line require "thread" to it. This has done nothing. EDIT: Just found another way which was rvm install rubygems 1.4.2 and it gave: Removing old Rubygems files... Installing rubygems dedicated to ruby-1.8.7-p334... Retrieving rubygems-1.4.2 % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 288k 100 288k 0 0 282k 0 0:00:01 0:00:01 --:--:-- 414k Extracting rubygems-1.4.2 ... Installing rubygems for /home/ubuntu/.rvm/rubies/ruby-1.8.7-p334/bin/ruby ERROR: Error running 'GEM_PATH="/home/ubuntu/.rvm/gems/ruby-1.8.7-p334:/home/ubuntu/.rvm/gems/ruby-1.8.7-p334@global:/home/ubuntu/.rvm/gems/ruby-1.8.7-p334@global" GEM_HOME="/home/ubuntu/.rvm/gems/ruby-1.8.7-p334" "/home/ubuntu/.rvm/rubies/ruby-1.8.7-p334/bin/ruby" "/home/ubuntu/.rvm/src/rubygems-1.4.2/setup.rb"', please read /home/ubuntu/.rvm/log/ruby-1.8.7-p334/rubygems.install.log WARN: Installation of rubygems did not complete successfully. TL;DR please tell me how to downgrade rubygems on ubuntu 10.10 or upgrade gitorious to work with 1.6.2 gems

  Read the article

• Seeking (somewhat) better explanations about supporting > 2.1 TB hard drives.

  - by irrational John

  Today while Googling about I stumbled across posts claiming that Seagate plans to ship a 3TB drive sometime later in 2010. Unfortunately, the stuff I looked at all seemed to contain tidbits of info which I didn't think fit together properly. (I would link to some examples, but I'm only allowed 1 link per post at the moment). Now I really don't have any "need" to better understand the underlying tedious details of this. I am just curious. And confused. So ... some questions I'm hoping someone better informed than I might answer. The talk about a potential addressing problem in both the hardware and the software confused me. The assertion is that something called something called Long LBA addressing (LLBA) is needed in the Command Descriptor Block as a way to get around the current limits to access a hard drive bigger than ~2.1 (or ~2.2?) TB. OK, fine. But I thought the last time this problem came up it was solved by extending the length of the LBA field from 28 to 48 bits. (Remember this website? www.48bitlba.com) A 6 byte LBA is clearly large enough, so what's up with this LLBA talk. I thought this was all fixed back by Win XP SP2, if not sooner? And certainly all the hardware should be up to the task, shouldn't it? The real problem as I understand it with drives much bigger than 2 TB are the 4 byte LBA fields in the Master Boot Record (MBR) used to partition just about all hard drives at the moment. The most likely solution is to migrate to Intel's GUID Partition Table (GPT). A GPT uses 8 byte fields for the LBA. What I don't understand in this context is what is the problem with booting say Windows from a 3TB drive that uses a GPT. Granted, the current PC BIOS wouldn't know how to recognize or work with a GPT. But every GPT comes with a so-called "Safety" or "Guarding" MBR in sector 0.Apple already uses a hybrid version of the MBR to allow them to boot Windows on their Intel Macs (aka Boot Camp). Couldn't something similar be done to allow the PC BIOS to recognize and boot from a partition in, say, the first 1 GB of a 3GB or larger drive? I've got more questions such as where do 4K sectors fit into all of this. But it's probably time I just shut up and posted this. ;-) -irrational john

  Read the article

• How should I convert a physical drive to a VHD for use with VirtualPC?

  - by RBerteig

  I have the hard disks from a PC that was happily running Windows Me until is it suffered an unknown hardware failure. The drives are intact, and can be mounted and read on other PCs. We have data backups, but there is licensed software installed that may not be possible to migrate to newer versions running on a more modern platform making the idea of just booting a virtual image attractive. Is it possible to make VHDs from the drives such that I can boot them in VirtualPC? If not VirtualPC, would it be possible in any other virtualization tool? Edit: Some more details.... The system was running Windows Me, but upgraded from Windows 95 (or possibly 98). It can't have been more than a Pentium II, but I will have to look at the motherboard to confirm that. There were no "exotic" devices installed, and nothing beyond the usual legacy stuff that would need to survive into a virtual machine. The licensed software did not have a dongle, so I won't need to worry about virtualizing a physical dongle of some kind. Licenses were probably died to the disk serial number. There were two HDs, both IDE. The boot disk is about 6GB, and the spare data disk is 12GB, but nearly empty. I have a small bias in favor of VirtualPC just because its free and I've used it successfully in the past. But this is a good excuse to revisit the state of the art. I do know from direct experience that it is possible to install and boot DOS 5.0 and Win95 in VirtualPC, but the VM extensions weren't available so the experience isn't as seamless as I would have liked. A very old DirectX game that failed miserably under XP SP2 runs really nicely on that VM, and actually plays better in a lot of ways than it did on period hardware, so that gives me hope that this is possible. Edit 2: Well, I'm closer than I was when I asked... so thanks to all for helpful suggestions and hints to what I should be trying. I used WinImage to copy the disks, and VirtualPC 2007 to attempt to boot. So far, I have it booting in safe mode, but hanging with a black screen otherwise. I strongly suspect that the copy of Artisoft Lantastic 8.0 (anyone else remember them?) that is still installed for networking with even older PCs that mostly don't exist any more is the culprit there. In my infinite free time, I will try to resolve the differences between a Safe Mode boot and a normal boot, and feel that it is likely to yield to pressure. I'd accept more than one answer if I could... this isn't as black and white a question as the one accepted answer convention assumes.

  Read the article

• Windows 7, weird/annoying explorer problem

  - by Shiki

  First of all, I'm asking the moderators if you could summarize my problem in the Title and modify it according to that. Thanks in advance and sorry, my english is not that good. The problem. It happened on two of my machines already. Once it happens there are many problems with explorer. I'll try to describe at precisely I just can. So. Basically when you create a new folder, you have to hit the enter key TWICE because first it'll throw an error that "there is no such file..". Okay. Then if you try to delete some, this happens also. Renaming is the same. Here is an example. I tried adding a "2" to the end of the folder name, hit enter and got this. Here I can press cancel, nothing happens. If I press retry, the popup disappears and it'll finally change the folder name. I can't come up with anything for this. Using BitDefender (registered, full protection), Windows 7 x86 Ultimate retail (boxed, english version). The other PC had the same anti-virus protection , but it have a Windows 7 x64. Both systems are activated, updated totally. I don't remember installing any new stuff on the PCs. All the stuff on the PCs are legal, no cracked / any other software present. It just happened, so to say. Already reinstalled the other PC because I thought * I * messed up something and its just something FUBAR. However, I dont want to reinstall my laptop also. Any ideas are welcome. (Today I had a strange bug. Windows Explorer had 1.0+gb memory usage with 100% cpu. Killed it, launched a new explorer.exe and thats all. Nothing changed, but it may worth a try. The other PC did NOT have this problem, ever.) Isn't there a registry fix for this or something? :/

  Read the article

• Setting font size of Closed Captions on iPhone using ffmpeg or mencoder

  - by forthrin

  Does anyone know how to either: Make ffmpeg set subtitle font size in the output video file Make mencoder produce an iPhone-compatible video file (with subtitles) I finally found out how to get Closed Captions video on iPhone, with mkv and srt files as source material. The secret was using the mov_text subtitle codec in ffmpeg (and turning on Closed Captions in the iPhone settings of course): ffmpeg -y -i in.mkv -i in.srt -map 0:0 -map 0:1 -map 1:0 -vcodec copy -acodec aac -ab 256k -scodec mov_text -strict -2 -metadata title="Title" -metadata:s:s:0 language=eng out.mp4 However, the font size appears very small on the iPhone, and I can't find out how to set it with ffmpeg (the iPhone has no option for this). I found out that mencoder has a -subfont-text-scale option, but I don't have a lot of experience with this program. The following, my best attempt so far, produces an output file which is not playable on the iPhone. sudo port install mplayer +mencoder_extras +osd mencoder in.mkv -sub in.srt -o out.mp4 -ovc copy -oac faac -faacopts br=256:mpeg=4:object=2 -channels 2 -srate 48000 -subfont-text-scale 10 -of lavf -lavfopts format=mp4 PS! As requested, here is the output from mencoder: 192 audio & 400 video codecs success: format: 0 data: 0x0 - 0xb64b9d2f libavformat version 54.6.101 (internal) libavformat file format detected. [matroska,webm @ 0x1015c9a50]Unknown entry 0x80 [lavf] stream 0: video (h264), -vid 0 [lavf] stream 1: audio (ac3), -aid 0, -alang eng VIDEO: [H264] 1280x544 0bpp 49.894 fps 0.0 kbps ( 0.0 kbyte/s) [V] filefmt:44 fourcc:0x34363248 size:1280x544 fps:49.894 ftime:=0.0200 ========================================================================== Opening audio decoder: [ffmpeg] FFmpeg/libavcodec audio decoders libavcodec version 54.23.100 (internal) AUDIO: 48000 Hz, 2 ch, s16le, 448.0 kbit/29.17% (ratio: 56000->192000) Selected audio codec: [ffac3] afm: ffmpeg (FFmpeg AC-3) ========================================================================== ** MUXER_LAVF ***************************************************************** REMEMBER: MEncoder's libavformat muxing is presently broken and can generate INCORRECT files in the presence of B-frames. Moreover, due to bugs MPlayer will play these INCORRECT files as if nothing were wrong! ******************************************************************************* OK, exit. videocodec: framecopy (1280x544 0bpp fourcc=34363248) VIDEO CODEC ID: 28 AUDIO CODEC ID: 15002, TAG: 0 Writing header... [mp4 @ 0x1015c9a50]Codec for stream 0 does not use global headers but container format requires global headers [mp4 @ 0x1015c9a50]Codec for stream 1 does not use global headers but container format requires global headers Then the following repeats itself for every frame: Pos: 0.0s 1f ( 2%) 0.00fps Trem: 0min 0mb A-V:0.000 [0:0] [mp4 @ 0x1015c9a50]malformated aac bitstream, use -absf aac_adtstoasc Error while writing frame. I recognize -absf aac_adtstoasc as an ffmpeg option (does mencoder spawn ffmpeg?), but I don't know how to pass this option on (my hunch is this is not even the origin of the problem).

  Read the article

• Why do some games randomly turn my screen a random solid color?

  - by Emlena.PhD

  When playing some games my computer will randomly have an error that I cannot fix without turning it off and back on again. The screen changes to one solid color, which varies (off the top of my head I can remember seeing solid green, magenta, etc..) and the sound blares a single tone. The sound sometimes briefly restores and I can still hear the game sounds and even hear and still be heard by people in my Mumble channel, but the screen doesn't right itself so I'm still blind. What's more is this happens in some games but not in others. While the game is actually running, not while I'm still in the menu. However, it does happen if I'm afk or idle but the game world is still rendering. Games where the error occurs: League of Legends World of Warcraft Trine The Sims 2 Dungeon Defenders Safe games: games where it has never occurred: Tribes: Ascend Star Wars: the Old Republic Battlefield 3 So relatively older games cause the problem while newer games do not? I cannot predict when it will happen, it just seems random. However, if it happens and I try playing the same game further after restart it does appear to occur more frequently after the first time. But if I switch to a safe game it doesn't continue happening. Both of my RAM sticks appear fine, flipped position or either one on their own and games still run, computer still boots. I would think over-heating, but then why not all games? ALso, sometimes it happens immediately after I start playing, within seconds of the 3D world booting up. I'm looking to upgrade very soon so I want to figure out what component or software is fubar and replace/repair it. Any suggestions or recommendations of tools would be helpful. Below is some system information. Dxdiag does not detect any problems. Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.120305-1505) System Manufacturer: Gigabyte Technology Co., Ltd. System Model: EP45-UD3R BIOS: Award Modular BIOS v6.00PG Processor: Intel(R) Core(TM)2 Duo CPU E8500 @ 3.16GHz (2 CPUs), ~3.2GHz Memory: 4096MB RAM DirectX Version: DirectX 11 DxDiag Version: 6.01.7601.17514 64bit Unicode Graphics card name: NVIDIA GeForce GTX 285 Driver Version: 8.17.12.9610 (error has occurred w/several driver versions) Sound: I do not have a sound card, been using motherboard's built in sound)

  Read the article

• Configure vlan on Netgear switch via SNMP

  - by Russell Gallop

  I am trying to configure vlans on a netgear GS752TSX from the Linux command line with netsnmp. I have created vlan 99 on the web interface now want to control the pvid settings, egress and tagging. I have identified these as the MIBs I need to change: dot1qPvid.<port> dot1qVlanStaticEgressPorts.99 dot1qVlanStaticUntaggedPorts.99 Pvid works as I expect: $ snmpset -r 1 -t 20 -v 2c -c private <switch> dot1qPvid.17 u 99 Q-BRIDGE-MIB::dot1qPvid.17 = Gauge32: 99 $ snmpget -r 1 -t 20 -v 2c -c private <switch> dot1qPvid.17 Q-BRIDGE-MIB::dot1qPvid.17 = Gauge32: 99 and so do the egress ports: $ snmpset -r 1 -t 20 -v 2c -c private <switch> dot1qVlanStaticEgressPorts.99 x 'ff ff ff ff ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00' Q-BRIDGE-MIB::dot1qVlanStaticEgressPorts.99 = Hex-STRING: FF FF FF FF FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 $ snmpget -r 1 -t 20 -v 2c -c private <switch> dot1qVlanStaticEgressPorts.99 Q-BRIDGE-MIB::dot1qVlanStaticEgressPorts.99 = Hex-STRING: FF FF FF FF FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 But untagging the ports doesn't seem to remember my setting: $ snmpset -r 1 -t 20 -v 2c -c private <switch> dot1qVlanStaticUntaggedPorts.99 x 'ff ff ff ff ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00' Q-BRIDGE-MIB::dot1qVlanStaticUntaggedPorts.99 = Hex-STRING: FF FF FF FF FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 $ snmpget -r 1 -t 20 -v 2c -c private <switch> dot1qVlanStaticUntaggedPorts.99 Q-BRIDGE-MIB::dot1qVlanStaticUntaggedPorts.99 = Hex-STRING: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 I have tried netsnmp 5.4.1 and 5.7.2. Is there something I'm doing wrong?

  Read the article

< Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >