Search Results

Search found 71537 results on 2862 pages for 'virtual com port'.

Page 144/2862 | < Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >

  • Can i safely block all ports on my sever

    - by Saif Bechan
    I have a web server running pleks and get attacked a lot every day. I configured a firewall, and there are some predefined services such as www, and ftp, etc. I am planning to block all the ports except for the www port and the PLESK port. When I need ftp or ssh access for example i will open the ports in PLESK and then start to work. Is this a good thing to do or are there some downsides on doing this. There are some ports I am not sure of, such as SMTP,POP3,IMAP, DNS. Can i close these ports or is there no need to do so.

    Read the article

  • Multiple VLAN on one switch port

    - by Macropus
    I have a HP ProCurve 1810G-8 which I currently use as a normal switch between 3 servers and a firewall. 2 of the servers are ESXi hosts, and one is a Nexentastor box with 2 iSCSI target LUNs. As the iSCSI traffic is on the same LAN as all other traffic, I would like to switch this to use a SAN for iSCSI traffic and the LAN for all other traffic. The Nexentastor box only has 2 NICs, and as such, with a physical arrangement, I presume that one must be plugged into the SAN VLAN and one on the LAN VLAN ports of the switch. Is there a way to have multiple VLANs over the same port? e.g. the Nexentsator box has 2 NICs, both plugged into the switch, both ports with access to both of the VLANs?

    Read the article

  • Multiple IPs on Juniper SRX100 Untrust Port

    - by Will
    I am having trouble getting multiple IP addresses on the untrust port. I have tried a few different methods, but can't seem to get it to work. Does anyone have a good tutorial that is not easily found or if possible can type up the steps? I don't mind trying to do it through ssh, but would prefer web interface. Thank you ++++++++++++ Feb 1 fe-0/0/0 { unit 0 { family inet { dhcp { update-server; } } } } routing-options { static { route 0.0.0.0/0 next-hop 96.11.173.81; } } Right now it's setup to receive settings from 'cable modem' through dhcp, but I think it's only getting one IP.

    Read the article

  • DYNDNS setup with TightVNC on Windows Server 2008 R2

    - by StealthRT
    Hey all, i seem to be having a problem with getting ports to forward on my Windows Server 2008 R2 PC. I already set all my port forwarding for 5900/5800 on my router for my PC's IP address (192.168.1.22) but when i try to use the TightVNC PFPortChecker on port 5900 it tells me its not opened! I can not even connect to my DYNDNS server name (xxxxxxx.dyndns.org). As a side note, i am running Windows XP SP3 within a VirtaulBox inside Windows Server 2008 R2 but running the PFPortChecker in Windows 2008 R2 brings the same results as it does in the VM. I also added them to the Windows Firewall Advanced Security form to add those inbound ports for full access. What could i possibly be missing? Thanks for your time! David

    Read the article

  • Work firewall blocking Gmail IMAP port

    - by Sean
    My work has a very over protective firewall. We use Google Apps for our email and so can access the web interface just fine. I use my laptop at work however (MacBook connected via WiFi through my AirPort Express), and prefer to use Sparrow to check my email. The problem is that our firewall blocks whatever port Gmail's IMAP server uses. I'm trying to figure out the easiest way to work around this. I'm guessing I'll need to use an SSH tunnel or VPN, but I'm looking for specific instructions. I'd prefer to only route the IMAP stuff around the firewall as opposed to using a VPN full time. I have two computers at home (one PC, one Mac Mini) that are always on and could probably act as a server if needed.

    Read the article

  • How to free port 80 for xampp to work

    - by Alfie
    Please help, I used to be running xampp and it was working perfectly. Then I wanted to try something out and I ran IIS instead of xampp. Now I want to go back to using xampp, but whenever I try to run the apache server it says: Busy... Apache started [port 80] If I go to http://localhost/ then it just says that it can't establish a connection to the server. I have turned off IIS, so I don't see why it shouldn't work. Any suggestions?

    Read the article

  • Linux: find thin server running on port 80 and kill it

    - by Andrew
    On my Linux server I ran: sudo thin start -p 80 -d Now I'd like to restart the sever. The trouble is, I can't seem to get the old process to kill it. I tried: netstat -anp But what I see on port 80 is this: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN - So, it didn't give me a PID to kill... I tried pgrep -l thin but that gave me nothing. Meanwhile pgrep -l ruby gives me like 6 processes running. I don't really understand why multiple ruby threads would be running, or which one I need to kill... How do I kill / restart the thin daemon?

    Read the article

  • Convert from port numbers to protocol names in wireshark

    - by Berkay
    i'm simply using tshark -r botnet.pcap -T fields -E separator=';' -e ip.src -e tcp.srcport -e ip.dst -e tcp.dstport '(tcp.flags.syn == 1 and tcp.flags.ack == 0)' to see the all initiated "legal TCP" connections. However, i need the destination port number conversion to "http" "netbios" etc. i'm not using -n option, but still i get: 128.3.45.128;62259;208.233.189.150;80 This is what i'm trying to get: 128.3.45.128;62259;208.233.189.150;http or 128.3.45.128;62259;208.233.189.150;80;http is better option for me. any idea from tshark users? or any other tool suggestions?

    Read the article

  • Convert from port numbers to protocol names ?

    - by Berkay
    i'm simply using tshark -r botnet.pcap -T fields -E separator=';' -e ip.src -e tcp.srcport -e ip.dst -e tcp.dstport '(tcp.flags.syn == 1 and tcp.flags.ack == 0)' to see the all initiated "legal TCP" connections. However, i need the destination port number conversion to "http" "netbios" etc. i'm not using -n option, but still i get: 128.3.45.128;62259;208.233.189.150;80 This is what i'm trying to get: 128.3.45.128;62259;208.233.189.150;http or 128.3.45.128;62259;208.233.189.150;80;http is better option for me. any idea from tshark users? or any other tool suggestions?

    Read the article

  • How to change Linux hot key [migrated]

    - by Willie Wright Jr
    I would like to know if it is possible to change the hot key on a Linux distribution. I have already tried to re-configure the hot keys in the virtual box preferences but i have not been able to accomplish the results i am looking for. I am currently running a Linux Antergos in a Virtual Box and i would like to change the hot key to match the ? key of Mac Book Pro to improve workflow and swap the workstation hot key to Ctrl. Overall i would like to be able to save files in the Virtual Machine using ?+s, ?+r Etc...

    Read the article

  • How to open ports on router for better torrent performance

    - by Mehper C. Palavuzlar
    I've been using utorrent to download and upload torrents for a long time. Recently someone told me that I need to open port(s) for utorrent from my router settings for better downloading and uploading performance. Is it true? If yes, how can I do that? My utorrent version: 2.0 and the port used for incoming connections: 61829. My router: Yaksu S200 ADSL router modem and I can reach its settings via web interface. I looked at the settings but they seem a bit complicated to me. Other info you may need to know: I have dynamic IP. I'm using Win7 x64.

    Read the article

  • Two Routers - 1 Port Straight to First Router

    - by apples
    At my house we have two Wifi routers one's connected directly to the modem and the other is plugged in down stairs as a second network(Directly connected to the first router) Is there a way that I could make it so that I have the second router have its own network, but have one or two ports that would act as if they were directly connected to the first router? That way I can port forward to devices on the second router. Here are the information about the routers: Router 1 - Linksys WRT54G Running stock firmware Router 2 - Linksys E900 Running Tomato Firmware So to summarize what I'm asking is how would I have two networks from two routers but be able to connect directly to the first router through one of the ports on the second router. Here's a Visio Drawing of what I would like to look like

    Read the article

  • 3CX behind UT7.1 using a callcentric.com SIP account

    - by Corey
    Has anyone had any luck with getting 3CX working behind UT7.1 with a SIP account from callcentric.com? I am willing to reset my current UT box back to defaults, and start from there. I have a static public IP assigned to the external interface. My internal addressing is 192.168.76.0 . My 3CX box has 192.168.76.17 . Would anyone be willing to give me a step by step of changes to make in UT / 3CX. I currently have my UT box unplugged, and have replaced it with a Linksys unit. I have port forwarding setup for… TCP/UDP 5060 to 192.168.76.17 UDP 9000-9049 to 192.168.76.17 … and everything works great. I also have additional external IPs available if that helps.

    Read the article

  • using iptables to change a destination port but keep the ip the same.

    - by Scott Chamberlain
    I am playing around with transparent proxies, The current way I am doing things is the program makes a request to a computer on port 80, I use iptables -t nat -A OUTPUT -p tcp --destination-port 80 -j REDIRECT --to-port 1234 to redirect to my proxy that I am playing with. the proxy will send out a request to port 81 (as all outbound port 80 are being fed back in to the proxy so I want to do something like iptables -t nat -A OUTPUT -p tcp --destination-port 81 -j DNAT --to-destination xxxx:80 The problem lies with the xxxx part. How do I change the destination port without changing changing the destination ip? Or am I doing this setup completely wrong, I am learning after all and constructive criticism is definitely appreciated.

    Read the article

  • VirtualBox serial port, limit of two?

    - by Evan Carroll
    Using VirtualBox, Is there a limit of two serial ports per VM? I'm currently engaging in a task that requires more than two, but less than or equal to four ports. I'm at a loss of what to do to get COM3 and COM4 up? How do I do it if the Virtual Box GUI doesn't currently support more than two serial host devices? Can I configure them external to the GUI? Is there a hard-cap on two devices? And, if so, for the love of god, please entertain me with the reasoning? I know Windows and Linux don't impose such a limit, it would seem awkward to impose it in virtualization layer. This is for cheap dial-in project with proprietary Windows tools. I'm using a Quatech serial multiport adapter to provide the ports to multimodems.

    Read the article

  • The best software for users internet usage

    - by nikospkrk
    Hi, We are a small business using a Vigor 2820 as the internet router, and we'd like to install a software that could report any internet usage from our users. I already tried the "official" software made by Draytek called "SmartMonitor", but is reliability is a real issue as it doesn't seem to keep capturing packets after working 3 to 6hours (randomly), whereas Wireshark keeps capturing packets after that amount of time. As I'm really fed up with this tool, I'm looking for other solutions but I still want the same features: users statistics, websites ranking, users traffic, ... I already enabled the port mirroring feature, so it would be perfect if you could suggest me a port mirroring-based software (ideally freeware). I thought I had found the good one with Etherscout, but it just doesn't launch. I am even open to a tool that would "just" make some reports based on Wireshark captured files (*.pcap). Thank you for any of your suggestion, Nicolas.

    Read the article

  • emulate fake monitor on windows 7?

    - by Claudiu
    Is there any way to emulate a monitor on Windows 7? I have one physical monitor, and I want Windows to think I have two. I actually don't care whether the second monitor is visible anywhere, or if I can see it - everything rendered there may as well go to the equivalent of /dev/null - but I need Windows to think there is one there. The reason is that I want to run a virtual machine with two monitors with VirtualBox in seamless mode, and it doesn't let me go to seamless mode if there are more virtual monitors than physical ones. I don't need to see the second virtual monitor, but VirtualBox won't just stop displaying it like it did in earlier versions.

    Read the article

  • Automatically allowing SSH into a machine behind a UPNP router?

    - by GJ
    Hi I have a MacBook connecting to the Internet from behind various routers from time to time (home, office, etc). All of the routers support UPNP. I need to allow a co-worker to SSH into the machine, without configuring each router each time to forward port 22 to the MacBook. Is there any way to get the MacBook to use UPNP (or some other method) to automatically configure any supporting router that it is behind to forward port 22 to itself? That would allow the co-worker to SSH into the MacBook but just knowing its external IP, which is easy.

    Read the article

  • File and Printer Sharing Port issue in Windows 7 64 bit

    - by Mohit
    So, This is totally weird and I could not find any way to fix it. In simple words after the diagnosis this what is happening. On a windows 7 64 bit box, Whenever I am trying to access a server using file share. It is trying to connect to port 80 http on the place of 445. I observed that using WireShark. Telnet to 445 works. Any clue how to fix this. Scanned the machine using Malware bytes, Symantec and MS live essentials . I dont want to recreate the whole machine again. Please help me here. Regards Mohit Thakral

    Read the article

  • why can't macports find make

    - by GeoffreyF67
    I am trying to run macports like thus: port install php5 When I do so, however, I get this error: Error: Unable to open port: can't read "build.cmd": Failed to locate 'make' in path: '/opt/local/bin:/opt/local/sbin:/bin:/sbin:/usr/bin:/usr/sbin' or at its MacPorts configuration time location, did you move it? So I looked at my path: declare -x PATH="/Developer/usr/bin:/opt/subversion/bin:/opt/local/bin:/opt/local/sbin:/usr/local/php5/bin:/usr/bin:/bin:/usr/sbin:/sbin:/usr/local/bin:/usr/X11/bin" and then looked to make sure make was in one of those dirs: ls -l /Developer/usr/bin/make $ lrwxr-xr-x 1 root admin 7 Aug 7 16:47 /Developer/usr/bin/make -> gnumake And typing: make produces: make: *** No targets specified and no makefile found. Stop. So I know that it's there. But macports can't find it. Any ideas? G-Man

    Read the article

  • mystery Internet traffic to port 445

    - by Ben Collver
    Recently, I noticed traffic from the office network to TCP port 445 on the Internet [a]. Below are the Linux firewall log entries to Facebook's network [b] and Google's network [c]. I would like to identify the source of this traffic. My first guess is that Facebook and Google might be using multiple TCP ports for SSL load balancing. However, I could not confirm this based on the web proxy logs. What else might it be? [a] http://support.microsoft.com/kb/204279 [b] Sep 4 08:30:03 firewall01 kernel: IN=eth0 OUT=eth2 SRC=10.0.0.131 DST=69.171.237.34 LEN=52 TOS=0x00 PREC=0x00 TTL=127 ID=14287 DF PROTO=TCP SPT=51711 DPT=445 WINDOW=8192 RES=0x00 SYN URGP=0 [c] Aug 28 06:02:41 firewall01 kernel: IN=eth0 OUT=eth2 SRC=10.0.0.115 DST=173.194.33.47 LEN=52 TOS=0x00 PREC=0x00 TTL=127 ID=4558 DF PROTO=TCP SPT=49294 DPT=445 WINDOW=8192 RES=0x00 SYN URGP=0

    Read the article

  • Port based bandwidth shaping

    - by nixnotwin
    I have an interent connection with the speed of 4000k bits up and down. I want to do port based traffic shaping on a ubuntu machine, which acts as router. eth0 is the WAN interface. This is how I would like to allocate bandwidth: For ports 80 and 445 the bandwidth usage can go upto 90% For ports above 1024 upto 65535 the bandwidth usage can go upto 10% For remaining ports the bandwidth usage can go upto 40% The easiest way for achieving the above is using a router with tomato firmware. I have used it and it is very efficient. I want to try if it can be done on a Ubuntu or any GNU/Linux machine. I have googled extensively about the topic and I feel there isn't much information.

    Read the article

  • ipfw to redirect traffic from port 80 and 443 to 8080

    - by user1048138
    -A PREROUTING -s 10.0.10.0/24 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 8080 -A PREROUTING -s 10.0.10.0/24 -p tcp -m tcp --dport 443 -j REDIRECT --to-ports 8080 -A POSTROUTING -s 10.0.10.0/24 -o eth0 -j MASQUERADE The above code is what I have used on linux to forward my ports to 8080, how can I do the same on a mac? I have tried test_machine:~ root# ipfw show 00666 0 0 fwd 127.0.0.1,8080 tcp from any to me dst-port 80 and its not working! any suggestions?

    Read the article

  • Can you install Ubuntu Server in a Windows PC VM on Windows 7?

    - by Lance Fisher
    I am running Windows 7 64-bit. I've installed Windows Virtual PC and Windows XP Mode successfully. Next, I downloaded Ubuntu Server 9.04 32-bit. I created a new virtual machine with a dynamically expanding .vhd, loaded the Ubuntu .iso, and booted the machine. I successfully made it through the install, but when the machine reboots, I get a segmentation fault. Here is a screenshot. Has anyone successfully installed Ubuntu on Windows Virtual PC?

    Read the article

  • MySQL port 3306 became filtered when configured with Keepalived on Ubuntu server 12.04 lts

    - by Ludwig
    I'm configuring two load balancer (lb01 & lb02) with keepalived for my two mysql server (db01 & db02) with standard port 3306. There is virtual ip address (192.168.205.10) to access it also act as failover, but somehow the web server in the front can't access this mysql server using vip. Here is my config: Keepalived: Only the mysql part that i added here. LB01: virtual_server 192.168.205.10 3306 { delay_loop 6 lb_algo rr lb_kind DR protocol TCP real_server 192.168.205.4 3306 { weight 10 TCP_CHECK { connect_port 3306 connect_timeout 2 } } } LB02: virtual_server 192.168.205.10 3306 { delay_loop 6 lb_algo rr lb_kind DR protocol TCP real_server 192.168.205.6 3306 { weight 10 TCP_CHECK { connect_port 3306 connect_timeout 2 } } } I already comment out the "bind-address=127.0.0.1" part in both server my.cnf. Also, remove all the firewall prog from my ubuntu server (ufw or iptables). Any help? thanks.

    Read the article

< Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >