Search Results

Search found 32200 results on 1288 pages for 'osx 10 6'.

Page 145/1288 | < Previous Page | 141 142 143 144 145 146 147 148 149 150 151 152  | Next Page >

  • Multicast hostname lookups on OSX

    - by KARASZI István
    I have a problem with hostname lookups on my OSX computer. According to Apple's HK3473 document it says for v10.6: Host names that contain only one label in addition to local, for example "My-Computer.local", are resolved using Multicast DNS (Bonjour) by default. Host names that contain two or more labels in addition to local, for example "server.domain.local", are resolved using a DNS server by default. Which is not true as my testing. If I try to open a connection on my local computer to a remote port: telnet example.domain.local 22 then it will lookup the IP address with multicast DNS next to the A and AAAA lookups. This causes a two seconds lookup timeout on every lookup. Which is a lot! When I try with IPv4 only then it won't use the multicast queries to fetch the remote address just the simple A queries. telnet -4 example.domain.local 22 When I try with IPv6 only: telnet -6 example.domain.local 22 then it will lookup with multicast DNS and AAAA again, and the 2 seconds timeout delay occurs again. I've tried to create a resolver entry to my /etc/resolver/domain.local, and /etc/resolver/local.1, but none of them was working. Is there any way to disable this multicast lookups for the "two or more label addition to local" domains, or simply disable it for the selected subdomain (domain.local)? Thank you! Update #1 Thanks @mralexgray for the scutil --dns command, now I can see my domain in the list, but it's late in the order: DNS configuration resolver #1 domain : adverticum.lan nameserver[0] : 192.168.1.1 order : 200000 resolver #2 domain : local options : mdns timeout : 2 order : 300000 resolver #3 domain : 254.169.in-addr.arpa options : mdns timeout : 2 order : 300200 resolver #4 domain : 8.e.f.ip6.arpa options : mdns timeout : 2 order : 300400 resolver #5 domain : 9.e.f.ip6.arpa options : mdns timeout : 2 order : 300600 resolver #6 domain : a.e.f.ip6.arpa options : mdns timeout : 2 order : 300800 resolver #7 domain : b.e.f.ip6.arpa options : mdns timeout : 2 order : 301000 resolver #8 domain : domain.local nameserver[0] : 192.168.1.1 order : 200001 Maybe it would work if I could move the resolver #8 to the position #2. Update #2 No probably won't work because the local DNS server on 192.168.1.1 answering for domain.local requests and it's before the mDNS (resolver #2). Update #3 I could decrease the mDNS timeout in /System/Library/SystemConfiguration/IPMonitor.bundle/Contents/Info.plist file, which speeds up the lookups a little, but this is not the solution.

    Read the article

  • getting firewatir to run on mac osx: jssh problems

    - by z3cko
    I am trying to get firewatir to run on Mac OSX Leopard. I have Firefox 3.6rc2 installed but running the most simple script does not work: require 'rubygems' require 'firewatir' ff=FireWatir::Firefox.new ff.goto("http://mail.yahoo.com") i am getting the following error /usr/local/lib/ruby/gems/1.8/gems/firewatir-1.6.5/lib/firewatir/firefox.rb:237:in `set_defaults': Unable to connect to machine : 127.0.0.1 on port 9997. Make sure that JSSh is properly installed and Firefox is running with '-jssh' option (Watir::Exception::UnableToStartJSShException) from /usr/local/lib/ruby/gems/1.8/gems/firewatir-1.6.5/lib/firewatir/firefox.rb:131:in `initialize' from ./watir-test.rb:12:in `new' from ./watir-test.rb:12 even when I am trying to start Firefox with the -jssh option, I get an error (although another one) /Applications/Firefox.app/Contents/MacOS/firefox-bin -jssh the error output in that case: /usr/local/lib/ruby/gems/1.8/gems/firewatir-1.6.5/lib/firewatir/firefox.rb:125:in `initialize': Firefox is running without -jssh (RuntimeError) is there any tutorial or hnt to get firewatir actually running on Mac OSX?

    Read the article

  • silverlight for .NET / CLR based numerical computing on osx

    - by Jonathan Shore
    I'm interested in using F# for numerical work, but my platforms are not windows based. Mono still has a significant performance penalty for programs that generate a significant amount of short-lived objects (as would be typical for functional languages). Silverlight is available on OSX. I had seen some reference indicating that assemblies compiled in the usual way could not be referenced, but not clear on the details. I'm not interested in UIs, but wondering whether could use the VM bundled with silverlight effectively for execution? I would want to be able to reference a large library of numerical models I already have in java (cross-compiled via IKVM to .NET assemblies) and a new codebase written in F#. My hope would be that the silverlight VM on OSX has good performance and can reference external assemblies and native libraries. Is this doable?

    Read the article

  • Next/Last word with Netbeans in Mac OSX

    - by Phuong Nguy?n
    I've just switched to Mac OSX from Ubuntu. The development on Mac OSX using Netbeans is really a joy (of hell, though) I don't know how to go to next word, last word using keyboard. In windows or ubuntu, this should be Ctrl+Left/Right, but definely not in Mac. In Mac, such key combinations result in go to begin/end of line. Futhermore, the use of Home and End is for something else, not go to begin/end of line (What a cool hell). Is there another key combination? I prefer default key settings, please. I'm sick of going around with custom script.

    Read the article

  • Correct Path for Git Remote Add from Amazon EC2 Instance to OSX Client Machine

    - by filmnut
    I'm trying to do a git remote add from a repository that sits on a remote Amazon AMI back to a cloned copy of the SAME repository that is sitting on my local OSX machine. I'm confused about what file path to use. I assume it's something like: git remote add my_clone <OSX_User_Name>@<OSX_HOST_NAME>:<PATH_TO_CLONED_REPO> I obviously know what my <OSX_User_Name> is, and I can figure out my <PATH_TO_CLONED_REPO>, but I have no idea how to determine a <OSX_HOST_NAME> that would actually work. Can I just put in my external IP address, followed by my machine's internal IP address? (Note that I'm working behind a router.) Is ssh:// the correct protocol? Do I need to set up ssh access from the Amazon EC2 machine to the local OSX machine?

    Read the article

  • "The connection has timed out" - Please help!

    - by gon
    I recently installed a fresh Ubuntu 12.04 LTS on a desktop, and the installation itself was successful (other than 'grub rescue' issue that I encountered but fixed) but this connection problem is really giving me a headache. Symptoms: 1. When I open the FireFox browser and try to connect to a website, it just hangs for a while saying "Connecting..." but eventually loads an error page "The connection has timed out". 2. It's not a browser problem (and I tried setting ipv6 thing to "true" at about:config) because running "sudo apt-get install [some-random-package]" at terminal fails ("E: Unable to locate package [package]") too. All other operations that need internet access are not working. 3. I certainly see a wired network (called "eth1") at the Network Manager, and it says "Connection Established" after disconnecting and then connecting again. I have tried almost everything that could be found from google search results still no luck. Their problems slightly differ from mine or the solutions just don't work. By the way it didn't have internet access when installing Ubuntu 12.04. (I ignored the message that I need internet to install Ubuntu) Could this be a problem? I'm sorry I don't remember if internet worked or not on the previous version of Ubuntu. :( I would really appreciate your help... I don't even know what more to do if this fails too.. Thanks!! Thanks for your comment. Here is the result of ifconfig: eth0 Link encap:Ethernet HWaddr 78:ac:c0:3d:b2:b9 inet addr:10.10.65.185 Bcast:10.10.65.255 Mask:255.255.255.0 inet6 addr: fe80::7aac:c0ff:fe3d:b2b9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3907 errors:0 dropped:0 overruns:0 frame:0 TX packets:771 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:393118 (393.1 KB) TX bytes:73472 (73.4 KB) Interrupt:16 eth1 Link encap:Ethernet HWaddr 78:ac:c0:3d:b2:b8 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204 (204.0 B) TX bytes:204 (204.0 B) route -n: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.10.65.1 0.0.0.0 UG 0 0 0 eth0 10.10.65.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 /etc/resolv.conf: # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 8.8.8.8 nameserver 8.8.4.4 nameserver 10.81.1.8 nameserver 10.1.2.10 nameserver 127.0.0.1 search yamatake.local /etc/network/interfaces: auto lo iface lo inet loopback #auto eth0 #iface eth0 inet dhcp #auto eth1 #iface eth1 inet dhcp And I'll also include the result of 'sudo lshw -C network' in case it might help: *-network description: Ethernet interface product: NetXtreme BCM5764M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 10 serial: 78:ac:c0:3d:b2:b9 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5764m-v3.35 ip=10.10.65.185 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:93 memory:fc000000-fc00ffff *-network description: Ethernet interface product: NetXtreme BCM5764M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth1 version: 10 serial: 78:ac:c0:3d:b2:b8 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5764m-v3.35 latency=0 link=no multicast=yes port=twisted pair speed=100Mbit/s resources: irq:94 memory:fb000000-fb00ffff

    Read the article

  • Perl on MacOS X 10.6.2: GDBM_File missing, how to install or work around?

    - by jdmuys
    When I need a Perl module, I typically use CPAN. It works fine. But not this time. I want to use MARC::Charset, but this one uses GDBM_File, and I can't seem to install GDBM_File from CPAN. CPAN finds it all right, but trying to install it, it starts installing the full Perl 5.10.1 distribution. MARC::Charset is a rather old module, so there should be a way to use it from some common Perl version (Mac OS X 10.6.2 has 5.10.0 and 5.8.9 by default). While installing the full blow Perl 5.10.1 is not an option, modifying MARC::Charset to stop using GDBM_File might be one. What would be the best course of action to do so? This last option might also be the only one. googling GDBM_File uncovers a few items that suggest that gdbm is not even available on the Mac. Those items typically went over my head though. While I don't expect a silver bullet, somebody may have a pointer or two on where I should start. After all, MARC::Charset only does character transliteration to/from the marc8 char set, which unfortunately, iconv doesn't seem to support.

    Read the article

  • MYSQL fetch 10 posts, each w/ vote count, sorted by vote count, limited by where clause on posts

    - by nibblebot
    I want to fetch a set of Posts w/ vote count listed, sorted by vote count (e.g.) Post 1 - Post Body blah blah - Votes: 500 Post 2 - Post Body blah blah - Votes: 400 Post 3 - Post Body blah blah - Votes: 300 Post 4 - Post Body blah blah - Votes: 200 I have 2 tables: Posts - columns - id, body, is_hidden Votes - columns - id, post_id, vote_type_id Here is the query I've tried: SELECT p.*, v.yes_count FROM posts p LEFT JOIN (SELECT post_id, vote_type_id, COUNT(1) AS yes_count FROM votes WHERE (vote_type_id = 1) GROUP BY post_id ORDER BY yes_count DESC LIMIT 0, 10) v ON v.post_id = p.id WHERE (p.is_hidden = 0) ORDER BY yes_count DESC LIMIT 0, 10 Correctness: The above query almost works. The subselect is including votes for posts that have is_hidden = 1, so when I left join it to posts, if a hidden post is in the top 10 (ranked by votes), I can end up with records with NULL on the yes_count field. Performance: I have ~50k posts and ~500k votes. On my dev machine, the above query is running in .4sec. I'd like to stay at or below this execution time. Indexes: I have an index on the Votes table that covers the fields: vote_type_id and post_id EXPLAIN id select_type table type possible_keys key key_len ref rows Extra 1 PRIMARY p ALL NULL NULL NULL NULL 45985 Using where; Using temporary; Using filesort 1 PRIMARY <derived2> ALL NULL NULL NULL NULL 10 2 DERIVED votes ref VotingPost VotingPost 4 319881 Using where; Using index; Using temporary; Using filesort

    Read the article

  • Xenserver 5.5 U2 a bit unstable with an unstable W2003 VM

    - by twistedbrain
    In the last week I had to reboot the host system twice and the second one by means of the power button. The system is a Dell PE 6950 (4 Opteron dual core, 2,8 Ghz, 16 GB RAM, 900 GB disk in a RAID 10 array composed by 4 450GB 15000 rpm disks) with XenServer 5.5 U2. We're installing it and at now there are working in production a 2003 32 bit Windows server VM with 2 GB RAM, 3 vcpu and about 200 GB disk in 4 partition (12 GB boot, 20 GB program, 80 GB user data, 80 GB other data). The first time I was compressing many Windows 2003 folders (some tens GB by means of W2003 compressed folder option) from a Windows remote console and some hours before my colleague installed Backup Exec agent that was alredy installed and that required a reboot (that was pending). The console stopped responding, it was no more possible to connect by means of remote console or by means of the console of the XenCentre, it was still possible from the network to use the shared folder of the VM and the programs on it (2 db and a GIS program), but the print server didn't work any more and I couldn't give remote reboot from other domain controller hosts. I couldn't stop the virtual machine neither from the XenCentre, neither from the command line of the host also forcing the reboot. I had to reboot the host server. Yesterday it has been worst. I installed a template of another VM, CentOS 5.3 and then, put the DVD in the drive of the host. Then, before the install and after the boot I checked for defect the DVD and the W2003 VM began to respond slowly (I was connected by means of an administration remote console) the task manager showed only mid or low load, it is, only the first of the 3 vcpu was loaded (about 70%), while the other two were about at 20% and also the disk I/O was not so heavy. Then the users were not so happy because they couldn't any more use the MS word docs on the server. I immediately stopped the check of the DVD (to do that I had to force the stop of such Centos 5.3 VM), then some users could again use their docs, but other had still problems, so I decided to reboot the VM, but it doesn't stopped, neither from XenCenter, neither from command line, neither forcing the reboot. Then I tried to reboot of the host, but it didn't worked, neither from the XenCentre, neither from the host prompt (shutdown -r now as root: it told that it was shutting down, but then it didn't did that). So I had to power off by means of the power button of the server (before I tried some Magic SyS REQ, but I saw that Xen isn't compiled with this option enabled). What could you suggest about my problem, what can I look, search and see? In the W2003 VM logs there are no errors or warning to explain what happened. Some more exciting, amusing and inspiring words of poetry (the facts happened around 11 am): \# egrep -i 'err|warning' xensource.log [20100219 10:32:05.597|debug|culo|6301 unix-RPC|VBD.plug R:c81bcda701f6|xenops] watch: watching xenstore paths: [ /xapi/0/frontend/vbd/51712/hotplug; /local/domain/0/backend/vbd/0/51712/tapdisk-error ] with timeout 1200.000000 seconds [20100219 10:32:05.597|debug|culo|6301 unix-RPC|VBD.plug R:c81bcda701f6|xenops] watch: fired on /local/domain/0/backend/vbd/0/51712/tapdisk-error [20100219 10:32:14.314|debug|culo|6335 unix-RPC|VBD.unplug R:9258f54578d6|xenops] watch: watching xenstore paths: [ /local/domain/0/backend/vbd/0/51712/shutdown-done; /local/domain/0/error/device/vbd/51712/error ] with timeout 1200.000000 seconds [20100219 10:32:14.337|debug|culo|6335 unix-RPC|VBD.unplug R:9258f54578d6|xenops] xenstore-rm /local/domain/0/error/backend/vbd/0 [20100219 10:32:14.337|debug|culo|6335 unix-RPC|VBD.unplug R:9258f54578d6|xenops] xenstore-rm /local/domain/0/error/device/vbd/51712 [20100219 10:32:14.338|debug|culo|6335 unix-RPC|VBD.unplug R:9258f54578d6|xenops] watch: fired on /local/domain/0/error/device/vbd/51712/error [20100219 10:53:48.903|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|helpers] Ignoring exception: INTERNAL_ERROR: [ Xb.Noent ] while Vmops.destroy_domain: Destroying domid 14 guest session [20100219 10:53:52.048|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/0/error/backend/tap/14 [20100219 10:53:52.048|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/14/error/device/vbd/51744 [20100219 10:53:52.085|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/0/error/backend/tap/14 [20100219 10:53:52.086|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/14/error/device/vbd/51728 [20100219 10:53:52.122|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/0/error/backend/tap/14 [20100219 10:53:52.122|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/14/error/device/vbd/51712 [20100219 10:53:52.127|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/0/error/backend/vbd/14 [20100219 10:53:52.128|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/14/error/device/vbd/51760 [20100219 10:53:52.496|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] Device.Vif.hard_shutdown about to blow away backend and error paths [20100219 10:53:52.497|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/0/error/backend/vif/14 [20100219 10:53:52.497|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/14/error/device/vif/0 [20100219 10:53:53.385|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] Device.Vif.hard_shutdown about to blow away backend and error paths [20100219 10:53:53.386|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/0/error/backend/vif/14 [20100219 10:53:53.386|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/14/error/device/vif/1 [20100219 10:53:53.389| warn|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|hotplug] Warning, deleting 'vif' entry from /xapi/14/hotplug/vif/0 [20100219 10:53:53.391| warn|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|hotplug] Warning, deleting 'vif' entry from /xapi/14/hotplug/vif/1 [20100219 11:20:49.766|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|helpers] Ignoring exception: INTERNAL_ERROR: [ Xb.Noent ] while Vmops.destroy_domain: Destroying domid 11 guest session [20100219 11:20:50.339|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/0/error/backend/tap/11 [20100219 11:20:50.339|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/11/error/device/vbd/832 [20100219 11:20:50.360|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/0/error/backend/tap/11 [20100219 11:20:50.360|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/11/error/device/vbd/768 [20100219 11:20:50.366|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/0/error/backend/vbd/11 [20100219 11:20:50.366|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/11/error/device/vbd/5696 [20100219 11:20:50.753|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] Device.Vif.hard_shutdown about to blow away backend and error paths [20100219 11:20:50.754|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/0/error/backend/vif/11 [20100219 11:20:50.754|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/11/error/device/vif/1 [20100219 11:20:50.757| warn|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|hotplug] Warning, deleting 'vif' entry from /xapi/11/hotplug/vif/1 [20100219 11:28:13.803|debug|culo|6610 inet-RPC|Connection to VM console R:e9f8b76e8975|console] error: INTERNAL_ERROR: [ Unix.Unix_error(63, "connect", "") ]

    Read the article

  • Connectivity issues with dual NIC machine in EC2

    - by Matt Sieker
    I'm trying to get some servers set up in EC2 in a Virtual Private Cloud. To do this, I have two subnets: 10.0.42.0/24 - Public subnet 10.0.83.0/24 - Private subnet To bridge these two, I have a Funtoo instance with a pair of NICs: eth0 10.0.42.10 eth1 10.0.83.10 Which has the following routing table: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.83.0 * 255.255.255.0 U 0 0 0 eth1 10.0.83.0 * 255.255.255.0 U 203 0 0 eth1 10.0.42.0 * 255.255.255.0 U 202 0 0 eth0 loopback * 255.0.0.0 U 0 0 0 lo default 10.0.42.1 0.0.0.0 UG 0 0 0 eth0 default 10.0.42.1 0.0.0.0 UG 202 0 0 eth0 An elastic IP is attached to the eth0 interface, and I can connect to it fine remotely. However, I cannot ping anything in the 10.0.83.0 subnet. For now iptables is not set up on the box, so there's no rules that would get in the way (Eventually this will be managed by Shorewall, but I should get basic connectivity done first) Subnet details from the VPC interface: CIDR: 10.0.83.0/24 Destination Target 10.0.0.0/16 local 0.0.0.0/0 [ID of eth1 on NAT box] Network ACL: Default Inbound: Rule # Port (Service) Protocol Source Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY Outbound: Rule # Port (Service) Protocol Destination Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY   CIDR: 10.0.83.0/24 VPC: Destination Target 10.0.0.0/16 local 0.0.0.0/0 [Internet Gateway ID] Network ACL: Default (replace) Inbound: Rule # Port (Service) Protocol Source Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY Outbound: Rule # Port (Service) Protocol Destination Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY I've been trying to work this out most of the evening, but I'm just stuck. I'm either missing something obvious, or am doing something very wrong. I would think I'd be able to ping from either interface on this box without issue. Hopefully some more pairs of eyes on this configuration will help. EDIT: I am an idiot. After I bothered to install nmap to run some more tests, I discover I can see the ports, and connect to them, pings are just being blocked.

    Read the article

  • VPC SSH port forward into private subnet

    - by CP510
    Ok, so I've been racking my brain for DAYS on this dilema. I have a VPC setup with a public subnet, and a private subnet. The NAT is in place of course. I can connect from SSH into a instance in the public subnet, as well as the NAT. I can even ssh connect to the private instance from the public instance. I changed the SSHD configuration on the private instance to accept both port 22 and an arbitrary port number 1300. That works fine. But I need to set it up so that I can connect to the private instance directly using the 1300 port number, ie. ssh -i keyfile.pem [email protected] -p 1300 and 1.2.3.4 should route it to the internal server 10.10.10.10. Now I heard iptables is the job for this, so I went ahead and researched and played around with some routing with that. These are the rules I have setup on the public instance (not the NAT). I didn't want to use the NAT for this since AWS apperantly pre-configures the NAT instances when you set them up and I heard using iptables can mess that up. *filter :INPUT ACCEPT [129:12186] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [84:10472] -A INPUT -i lo -j ACCEPT -A INPUT -i eth0 -p tcp -m state --state NEW -m tcp --dport 1300 -j ACCEPT -A INPUT -d 10.10.10.10/32 -p tcp -m limit --limit 5/min -j LOG --log-prefix "SSH Dropped: " -A FORWARD -d 10.10.10.10/32 -p tcp -m tcp --dport 1300 -j ACCEPT -A OUTPUT -o lo -j ACCEPT COMMIT # Completed on Wed Apr 17 04:19:29 2013 # Generated by iptables-save v1.4.12 on Wed Apr 17 04:19:29 2013 *nat :PREROUTING ACCEPT [2:104] :INPUT ACCEPT [2:104] :OUTPUT ACCEPT [6:681] :POSTROUTING ACCEPT [7:745] -A PREROUTING -i eth0 -p tcp -m tcp --dport 1300 -j DNAT --to-destination 10.10.10.10:1300 -A POSTROUTING -p tcp -m tcp --dport 1300 -j MASQUERADE COMMIT So when I try this from home. It just times out. No connection refused messages or anything. And I can't seem to find any log messages about dropped packets. My security groups and ACL settings allow communications on these ports in both directions in both subnets and on the NAT. I'm at a loss. What am I doing wrong?

    Read the article

  • Having XP VM use my host OSX ssh tunnel to connect to a remote site?

    - by Manachi
    I am using Mac OSX and have Windows XP running on VMWare Fusion. I'm creating an ssh tunnel from OSX to a remote server, and then trying to have Windows XP use that tunnel (I actually use a program called Proxifier on XP to filter my XP MS SQL Server traffic through that tunnel) Note that I can successfully create an ssh tunnel (on port 9333) from the XP putty to the remote host, and have SQL Server Proxify through that tunnel and it all works correctly. However when I try to set up the tunnel in OSX, and have Proxifier in XP point to the OSX tunnel instead of localhost, it doesn't seem to connect. Here is the OSX command i'm using to create the tunnel: ssh -i /my/key -p 9001 -D 9333 -g me@remotehostname Then I set my XP proxifier to point to macosxhostname:9333 (instead of the previous localhost:9333 which worked corrently when using putty) Any suggestions on what I may have missed? My XP firewall is turned off while setting this up.

    Read the article

  • Files Corrupted on System Restore

    - by Yar
    I restored OSX 10.6.2 today (was 10.6.3 and not booting) by copying the system over from a backup. The data directories were not touched. I am seeing some files as 0 bytes, and getting permission-denied errors when copying, even when using sudo cp or the Finder itself. Some programs, differently, take the files at face value and see no permission problems (such as zip), but they see the files as zero bytes, which would be game-over for recovery. cp: .git/objects/fe/86b676974a44aa7f128a55bf27670f4a1073ca: could not copy extended attributes to /eraseme/blah/.git/objects/fe/86b676974a44aa7f128a55bf27670f4a1073ca: Operation not permitted I have tried sudo chown, sudo chmod -R 777 and sudo chflags -R nouchg which do not change the end result. Strangely, this is only affecting my .git directories (perhaps because they start with a period, but renaming them -- which works -- does not change anything). What else can I do to take ownership of these files? Edit: This question comes from StackOverflow because I originally thought it was a GIT problem. It's definitely not (just) GIT. Anyway, this is to help put some of the comments in context.

    Read the article

  • Leopard Network Shares and browsing are unreliable

    - by EvilChookie
    I have two macs, running Leopard 10.5.8. One is the 13" MBP connected via WiFi, and the other is a 24" 2008 iMac, connected via ethernet. There are at least another 6-10 machines (windows and mac) awake on the network (with shares) at any given time, yet there are plenty of times where I cannot see any devices/shares in either my "Shared" section in Finder, nor can I see any computers in "Network" in Finder. Restarting doesn't help. I've restarted all the networking gear in the house to no avail. Our network is a series of gigabit switches connected to a D-Link gaming router. I believe we use OpenDNS, and our provider is Cox. I hate having to use "Go - Connect to Server" to browse to commonly used file shares (by IP). I'd like to know why my shares do not always and consistently appear in Leopard. Edit: I ran OnyX this morning, and performed the cleaning and maintenance operations (including disk permissions) on both my Macs, and at least one of my macs has started showing network devices again. (the other is still going). No idea how long this will last. Any ideas as to what is causing this issue, and how to prevent it? Edit 2: Aaaand there the shares go again. So running OnyX is not a permanent or reliable fix for this issue. Edit 3: After a clean reinstall and update, network shares are still unreliable. The SMBClient command mentioned in comments shows me the information it's supposed to show, but the shares do not appear in the shared section. They'll also vanish at random and reappear at random throughout the day.

    Read the article

  • Mac OS X L2TP VPN won't connect

    - by smokris
    I'm running Mac OS X Server 10.6, providing an L2TP VPN service. The VPN works just fine when connecting from all computers except one --- this one computer stays at the "Connecting..." stage for a while, then says "The L2TP-VPN server did not respond". In the console, I see this: 6/7/10 10:48:07 AM pppd[341] pppd 2.4.2 (Apple version 412.0.10) started by jdoe, uid 503 6/7/10 10:48:07 AM pppd[341] L2TP connecting to server 'foo.bar.baz.edu' (256.256.256.256)... 6/7/10 10:48:07 AM pppd[341] IPSec connection started 6/7/10 10:48:07 AM racoon[342] Connecting. 6/7/10 10:48:07 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 1). 6/7/10 10:48:08 AM racoon[342] IKE Packet: receive success. (Initiator, Main-Mode message 2). 6/7/10 10:48:08 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 3). 6/7/10 10:48:08 AM racoon[342] IKE Packet: receive success. (Initiator, Main-Mode message 4). 6/7/10 10:48:08 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 5). 6/7/10 10:48:11 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). 6/7/10 10:48:14 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). 6/7/10 10:48:17 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). ...and the "retransmit" messages continue until the error message pops up. So far I've unsuccessfully tried: rebooting deleting the VPN profile and recreating it verifying the client's internet connection (it is able to reach the VPN server) connecting through several different networks (in case a router was blocking VPN packets) disabling the Mac OS X Firewall on the client making sure that the VPN settings exactly match those of other working computers running software update (the client is on 10.6.3) Any ideas?

    Read the article

  • OS X AFP shares and access

    - by gbrandt
    I am running 10.5.6 Client as a mini server and am having problems with AFP shares. All clients are OS X 10.5.7 I have created three users for 'File Sharing' only on the 'server'. I have created groups and placed these users into specific groups. I have created ACL's to give each group access to certain shares. Two of those users can read and write to any share, one user cannot write to the shares, with different results: when copying a directory, only the directory is created, no files inside are copied, the OS does not give any errors when copying a single file I get three dialogs: "You may need to enter the name and password for an administrator on this computer to change the item named 'xxxx', "The item 'xxxxx' contains one or more items you do not have permission to read. Do you want to copy the items you are allowed to read?, and, The operation cannot be completed because you do not have sufficient priveleges for some of the items. With the single file, a file gets created on the server, but is empty. My ACL for the group this user belongs to is: 0: group:projectmembers allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit 1: group:informationtechnology inherited allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit 2: group:executive inherited allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit 3: group:everyone inherited deny list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit User 1 & 2 belong to informationtechnology and executive and projectmembers, they can read and write freely on the share. User 3 belongs to projectmembers and cannot read and write freely. I have read that this is a UID issue, however User 1 & 2 do not have matching UID's across clients and server and they work, so I don't think this is the case. Any ideas?

    Read the article

  • LSI 9260-8i w/ 6 256gb SSDs - RAID 5, 6, 10, or bad idea overall?

    - by Michael Pearson
    We're provisioning a new production server for our reasonably busy website. Our choice of host have available a 6 drive configuration with a LSI 9260-8i card. My initial thought was to fill all six bays with SSDs (Intel 520 256gb) and set them up in RAID. Good, bad, or terrible idea? Can the card handle it? Should we be using RAID 5, 6 or 10? This would be the first time the provider have filled all six slots for this rackmount with SSDs, so they're a bit hesitant. I'm wondering if somebody else with this card has done something similar in a production environment. We do about 43gb of writes per day and currently use about 300gb of storage. The server acts as webserver, database, and image store for approx 1 million files. The plan is to underprovision the SSDs by approximately 10% to 20% to increase their overall lifespan & performance. The fallback option is 2x480gb SSDs in RAID 1 and another 2x1TB HDDs in RAID 1. The motivation behind this is that the server rental cost difference between 2xSSDs and 6xSSDs is minimal (compared to the overall cost of the rental). We do not have any special high-IOPs requirements. However, if the configuration is known to work, I don't see a good reason to not use it and not have to worry about having separate 'fast and small' and 'slow and large' disks.

    Read the article

  • Why a 10 years old software still is so slow even today?

    - by Cawas
    I just noted this question due to a game (which happens to be Diablo 2), but the matter of fact is: why is my brand new mac book pro, made in 2009 with latest technology (tho it's the cheapest one) can't rival my computer which used to run this much faster back in 2000? Really, it was much faster on my AMD K6 450 back in those days, and I could even run two clients at same time with no slow down. I've always had the feeling this machine was slow, but this is a very odd way to attest it. Granted, the machine is smaller, runs on wifi and "boots" way faster thanks to sleep mode. But other than that, what have we evolved after all?! I'm pretty sure this shouldn't be graphical card's fault. Sure if I buy latest technology it will run fast, and probably most people here can confirm this and won't even understand my question. But the thing is, all the hardware is supposedly much faster and better than the stuff from 10 years ago. The software and operating system became more complex, but also more well refined. Now I'm trying a piece of software that is actually 10 years old and it's not getting any better results! Why?

    Read the article

  • How to set up TightVNC Java viewer index.html on web server?

    - by penyuan
    I've got the Java TightVNC viewer applet set up with the provided index.html on my Mac OS X 10.6.3 with web sharing enabled. Using a remote computer I was able to get to the webpage but I only see a white box with an X (for error?) that represents where the viewer is supposed to be. Any ideas on how to get this to work? I've tried to set the port (in index.html) to 5900 and 5901, none worked. Are any of these the default VNC port for Mac OS X 10.6.3? Also, I've activated Screen Sharing and Remote Login in System Preferences, allowing VNC viewers to connect. Here is the code for my index.html: <HTML> <TITLE> TightVNC desktop </TITLE> <APPLET CODE="classes/VncViewer.class" ARCHIVE="classes/VncViewer.jar" WIDTH="1440" HEIGHT="900"> <PARAM NAME="PORT" VALUE="5900"> <PARAM NAME="Scaling factor" VALUE="50"> </APPLET> <BR> <A href="http://www.tightvnc.com/">TightVNC site</A> </HTML> Again I can get to this page, but the applet doesn't seem to work, the Java console also doesn't say anything. Thanks in advance for your help!

    Read the article

  • Symlinks are inaccessible by their full path on OS X

    - by Computer Guru
    Hi, I have symlinks pointing to applications placed in /usr/local/bin which is in the path. However, I can't run these applications from other folders. Even more weird, I can't access them by the full path to the symlink. [mqudsi@iqudsi:Desktop/EasyBCD]$ echo $path (03-26 13:42) /opt/local/bin /opt/local/sbin /usr/local/bin /usr/local/sbin/ /usr/local/CrossPack-AVR/bin /usr/bin /bin /usr/sbin /sbin /usr/local/bin /usr/X11/bin [mqudsi@iqudsi:local/bin]$ ls -l /usr/local/bin (03-26 13:47) total 24280 -rwxr-xr-x 1 mqudsi wheel 18464 May 14 2009 ascii-xfr -rwxr-xr-x 1 mqudsi wheel 12567 Mar 25 04:50 brew -rwxr-xr-x 1 mqudsi wheel 17768 Dec 11 12:41 bsdiff -rwxr-xr-x 1 mqudsi wheel 43024 Mar 28 2009 dumpsexp -rwxr-xr-x 1 mqudsi wheel 280 Sep 10 2009 easy_install -rwxr-xr-x 1 mqudsi wheel 288 Sep 10 2009 easy_install-2.6 -rwxr-xr-x 1 mqudsi wheel 39696 Apr 5 2009 fuse_wait lrwxr-xr-x 1 mqudsi wheel 29 Mar 25 04:53 git -> ../Cellar/git/1.7.0.3/bin/git [mqudsi@iqudsi:local/bin]$ /usr/local/bin/git (03-26 13:47) zsh: no such file or directory: /usr/local/bin/git Clearly the link is there, but I'm not able to get it to it :S

    Read the article

  • Attempting to bootstrap and getting weird errors

    - by miah
    I'm on a new computer(mac 10.9.2) and I am attempting to bootstrap my companies project, but setuptools is failing. I can run python bootstrap.py, which creates the ./bin/buildout, but when I run the buildout, it returns the following error: Traceback (most recent call last): File "./bin/buildout", line 17, in <module> import zc.buildout.buildout File "/Users/miah/Documents/realmassive/joson/eggs/zc.buildout-1.7.1-py2.7. egg/zc/buildout/buildout.py", line 40, in <module> import zc.buildout.download File "/Users/miah/Documents/realmassive/joson/eggs/zc.buildout-1.7.1-py2.7. egg/zc/buildout/download.py", line 20, in <module> from zc.buildout.easy_install import realpath File "/Users/miah/Documents/realmassive/joson/eggs/zc.buildout-1.7.1-py2.7. egg/zc/buildout/easy_install.py", line 29, in <module> import setuptools.archive_util File "build/bdist.macosx-10.9-intel/egg/setuptools/archive_util.py", line 15, in <module> ImportError: cannot import name ContextualZipFile I've attempted installing it via https://pypi.python.org/pypi/setuptools#unix-including-mac-os-x-curl and homebrew.

    Read the article

  • Microsoft Arc Mouse OS X

    - by meepz
    I recently bought a new Mac Book Pro with Mountain Lion 10.8 on it. The only portable mouse I have is my Microsoft Arc Mouse. I wanted to use it with the laptop so I installed the IntelliPoint 8.2 for Mac from Microsofts website. According to their website, this driver is for OS X 10.4-10.7. Now I thought that wouldnt be too much of an issue but unfortunately for me, the driver installs fine and the mouse is detected but I get no movement and when I click the buttons nothing happens. I took the mouse with me on a business trip to EU and before I left I checked if the mouse worked with my desktop which is running Windows 7 and it worked without any hiccups. I'm not too sure where the OS differs from 10.7 to 10.8. I found an article online but it doesn't pertain to my mouse, although it could be of assistance. I have tried my version of their adjustment but I am not too knowledgable on low level hardware/software modifications so I may have done it wrong. heres the link: http://refluxions.wordpress.com/2008/08/18/mac-os-x-mouse-madnessfixed/ I get the following details when I check mouse info in the IntelliPoint preferences pane: The following Microsoft mouse devices are currently connected to your Macintosh driven by the Intellipoint software. Arc Mouse Vendor name: Microsoft Product name: Microsoft AE 2.4GHz Transceiver 5.0 Vendor ID: 045E Product ID: 074F Device version: 0140 if anyone has any suggestions on how to fix this it would be greatly appreciated! I love the mouse and im here in EU for another two weeks. Thanks

    Read the article

  • [Mac OS X] Terratec Cinergy Hybrid T USB XS is not recognized anymore

    - by Gabble
    I have used Terratec Cinergy Hybrid T USB XS for years now, alongside with Elgato EyeTV software. I am a happy and completely satisfied user! Since a couple of weeks the USB sitck stopped working on my MacPro1,1 (OS version 10.6.3): EyeTV does not see any device attached, and actually, the green led on the stick stays off. 1) it is not a USB port fault: I have unplugged any other USB/Firewire device and tried with different USB ports, to no avail (any other USB devices work as expected on any port) 2) I have completely uninstalled EyeTV software, including preferences and system daemons/extensions, rebooted and reinstalled the latest EyeTV. No way. 3) reset the PRAM. Nope. 4) checked the Apple System Profiler - USB: No device attached, The MacPro does not see it at all. ============= I need to say that: a) the device worked as a charm even with the latest OS 10.6.x (so it's not a OS upgrade cause) b) I have plugged the Terratec Cinergy Hybrid T USB XS to my MacBook5,1 where EyeTV is not installed and was never installed: The green led on the stick turns on, the growl bubble pops up, and the device is perfectly recognized by the system. Apple System Profiler says (sorry, Italian language): Cinergy Hybrid T USB XS (2882): ID prodotto: 0x005e ID fornitore: 0x0ccd Versione: 1.10 Numero di serie: 061102005755 Velocità: Fino a 12 Mb/sec Produttore: TerraTec Electronic GmbH ID posizione: 0x04100000 Corrente disponibile (mA): 500 Corrente necessaria (mA): 500 At this point I am pretty sure the Terratec stick is not damaged and there is something wrong with my MacPro. I kindly ask you: Is there a way to force my MacPro recognize the USB device? What can I check? Is there something that caches USB connection that can be reset? A OS reinstall would be the very last resort for me… Thanks in advance for any help you will offer!

    Read the article

  • Force Juniper-network client to use split routing

    - by craibuc
    I'm using the Juniper client for OSX ('Network Connect') to access a client's VPN. It appears that the client is configured to not use split-routing. The client's VPN host is not willing to enable split-routing. Is there a way for me to over-ride this configuration or do sometime on my workstation to get the non-client network traffic to by-pass the VPN? This wouldn't be a big deal, but none of my streaming radio stations (e.g. XM) work will connected to their VPN. Apologies for any inaccuracies in the terminology. ** edit ** The Juniper client changes my system's resolve.conf file from: nameserver 192.168.0.1 to: search XXX.com [redacted] nameserver 10.30.16.140 nameserver 10.30.8.140 I've attempted to restore my preferred DNS entry to the file $ sudo echo "nameserver 192.168.0.1" >> /etc/resolv.conf but this results in the following error: -bash: /etc/resolv.conf: Permission denied How does the super-user account not have access to this file? Is there a way to prevent the Juniper client from making changes to this file?

    Read the article

  • Delete ARP cache on Mac OS when moving from one Wifi network to the other

    - by Puneet
    I am facing wireless connectivity problems when I move from one Wifi network to the other. Here is how it happens: I am at my friends place. I connect to his Wifi. His Wifi router ip address is 192.168.0.1. Everything is fine I close my laptop, come back to my house, open my laptop and I connect to the Wifi Network at my place. Different ESSID, but the Wifi router address is the same 192.168.0.1. At this point I cant get to anything on the internet. To debug I try to see if I can ping the router (192.168.0.1), I cant. I get a no route to host. Meanwhile airport tells me Im connected to Wifi. I see the arp cache and I see a permanent entry for 192.168.0.1 ? (192.168.0.1) at 5c:d9:98:65:73:6c on en1 permanent [ethernet] This permanent bit looks problematic. I go ahead and delete the arp cache entry and all is fine with the world until I go back to my friends place where the same situation plays out. Now my question is, why the hell is this happening? If there is no way around it, can I run a script on Wifi connect/disconnect to clear out the arp cache? Im using Mac OS X $uname -a Darwin 10.8.0 Darwin Kernel Version 10.8.0: Tue Jun 7 16:33:36 PDT 2011; root:xnu-1504.15.3~1/RELEASE_I386 i386

    Read the article

< Previous Page | 141 142 143 144 145 146 147 148 149 150 151 152  | Next Page >