Search Results

Search found 4761 results on 191 pages for 'series'.

Page 147/191 | < Previous Page | 143 144 145 146 147 148 149 150 151 152 153 154  | Next Page >

• No video signal at boot with custom built computer

  - by Bart Pelle

  After booting my custom built computer, neither the VGA nor the HDMI methods from the video card seem to emit any signal to the display. I have tested both a regular VGA screen and a modern HDMI screen. Both did not receive signal. Below are the specifications from my computer build: Intel Core i5 3350P ASRock B75 Pro 3-M Seagate Barracuda 7200.14 ST1000 DM003 1000GB Corsair Vengeance LP CML 8GX 3M2 A1600 CGB Blue (2 cards) Cooler Master B Series B600 Club 3D Radeon HD7870 XT Jokercard Samsung SH-224 BB Black Sharkoon T28 Case The motherboard does not emit any beeps on startup. The CD tray opens properly and all fans spin. All cables are properly connected. All components are new and no damage was found on any of the components. The fans on the GPU spin aswell. The VGA test we did was by using the onboard graphics from the Intel i5, but this gave no result. The HDMI test was from the GPU which did not emit any signal either. We have not been able to test out the DVI, could this be important to test, even though all the other methods did not work? Thank you for your time and hopefully reply.

  Read the article

• Mystery 0xc0000142 error on starting java from a service, as a different user.

  - by cpf

  This is a very convoluted setup, but effectively this is what goes down: Manager service (which I don't have control over) running as admin user X starts my executable, which then starts Java as user Y using the standard c# StartInfo.Username/Password controls. Now, from a basic (not elevated or anything, just admin) command prompt I can run that executable, and Java pops up and works fine, running perfectly under the user it should be. When the service runs the same executable, however, Java silently fails. The only hint I see is this series of events in the event viewer: Service starts "Application popup: java.exe - Application Error : The application was unable to start correctly (0xc0000142). Click OK to close the application. " (googling this reveals a lot of scam sites telling me to use their "free antivirus to fix 0xc0000142 errors easy!"... sigh) Service stops (the java shutdown propagated, which is supposed to happen) And here's what process explorer has for the failure: As you can see, everything shows as a success. Now, I think this might have something to do with the permissions (the user java.exe is running under has traverse permission for the entire drive and full permissions to Directory A, which is where the .jar is), but I just can't fathom how something that works fine from the command line (and, this is an upgrade, the previous system without the user-switching aspect works fine from the service) can fail with such a cryptic message and little showing up in logs.

  Read the article

• Windows Server 2008 R2 Virtual Network Setup

  - by jpearl01

  Hi all, Some background: I'm very much new to networking in general, and virtualization in particular. I'm trying to set up a series of VMs as we are transitioning to a thin client setup. I have been supplied a limited number of static ip addresses. The server is located in an offsite building which houses the network we use to connect to the internet, share folders etc. The setup I've been trying to go for is this: The host OS (Windows Server 2008 R2) is bound to one nic using one of the static ips (say, Nic1 and ip 10.255.6.61). I've set up another external virtual network attached to another physical nic , and a virtual private network attached to no nic. There is one VM running the same os (as the host). This VM is connected to both the external virtual network (and uses another static ip say Nic2 and ip 10.255.6.62) and also to the virtual private network (I gave it a static random ip 192.168.88.1 subnet mask 255.255.255.0). This virtual private network is connected to all the other VMs. I'd like to share the internet connection with all the other VMs on the private virtual network, and so I installed the RRAS role on the server connected to Nic2, and selected the option to share the internet over the vpn. I've run through the RRAS wizard a few times, trying different configurations, but none of them seem to be letting the other vms connect to the 'net. The vms seem to connect to the virtual private network fine, they are assigned an ip address and everything, but no internet, and no rest of the network either. The other problem is in general I connect to the vms with RDP. Will that be possible with a setup like this? i.e. will the vms show up as computers on the network? If not, what are my other options? Thanks! ~josh

  Read the article

• Xmonad on windows laptop

  - by Kevin L.

  I'm a Linux developer in the market for a laptop. 90% of my time is spent in Emacs, the terminal, and Google Chrome, and I want to use them within the excellent Xmonad tiling windows manager. Given these constraints, I can only see two options: Run Linux on a laptop Run Windows on the laptop, and spend all of my time working within a Linux VM. Years of experience suggest that the first option will take many frustrating hours and probably be suboptimal w.r.t. battery life, wifi, and fn keys like screen brightness or audio adjustment. For the second option, what would be the ideal setup? I've had a lot of luck with Cooperative Linux on my Samsung NC-10 netbook (Windows XP), but I would have to setup the X11 server myself. What about using VirtualBox (which includes the guest VM's GUI)? Has anyone tried this? Hardware-wise, I'm looking for something in the "Macbook Air killer" category; Samsung Series 9 laptop, Lenovo IdeaPad U300s, &c. (i.e., matte screen, 5h+ battery life, 3ish pound weight). Price is not a consideration; any suggestions?

  Read the article

• How to encourage Windows administrators to pick up scripting?

  - by icelava

  When I worked as an administrator in my first job, I was frustrated that our administration processes with Windows servers were a series of point-and-clicks; we could never match the level of efficiency with the Unix servers which had a group of shell scripts to automate a lot of the work. I soon read about WSH and ADSI and wasted no time learning just how much automation I was able to achieve with scripting. There was a huge problem though - almost none of my Windows colleagues were really interested in learning scripting. They seemed happy with the manually mouse-clicking chores and were never excited at the prospect of using scripts to do the work on their behalf. I struggled to convince them to pick up scripting skills despite the evident increases in efficiency. I left that job in pursuit of a full-time software development career thereafter. Almost a decade on working in various environments and different customers, I still encounter Windows administrators mainly possessing this general "mood" where they would avoid scripting as much as possible. Despite the increasing level of accessibility Windows server technologies are opening up for scripting and automation. I am almost certain the majority of administrators are administrators precisely because they absolutely hate performing any kind of programming duties. What are some means to encourage and motivate administrators that scripting can really help them in the long run?

  Read the article

• Bad Mumble control channel performance in KVM guest

  - by aef

  I'm running a Mumble server (Murmur) on a Debian Wheezy Beta 4 KVM guest which runs on a Debian Wheezy Beta 4 KVM hypervisor. The guest machines are attached to a bridge device on the hypervisor system through Virtio network interfaces. The Hypervisor is attached to a 100Mbit/s uplink and does IP-routing between the guest machines and the remaining Internet. In this setup we're experiencing a clearly recognizable lag between double-clicking a channel in the client and the channel joining action happening. This happens with a lot of different clients between 1.2.3 and 1.2.4 on Linux and Windows systems. Voice quality and latency seems to be completely unaffected by this. Most of the times the client's information dialog states a 16ms latency for both the voice and control channel. The deviation for the control channels mostly is a lot higher than the one of the voice channels. In some situations the control channel is displayed with a 100ms ping and about 1000 deviation. It seems the TCP performance is a problem here. We had no problems on an earlier setup which was in principle quite like the new one. We used Debian Lenny based Xen hypervisor and a soft-virtualised guest machine instead and an earlier version of the Mumble 1.2.3 series. The current murmurd --version says: 1.2.3-349-g315b5f5-2.1

  Read the article

• Setting up xpra for client use in OS X

  - by Jonathan

  I've been trying to get xpra to run on OS X for the last few days to connect to my Ubuntu server. Note that there's a GUI for it called shifter, but that (at least on OS X) is still far too buggy. For those who don't know what xpra is, if you know what screen is, it's like screen for GUI X Windows apps tunneled over ssh. You can render a remote X app locally so it's faster than sending a series of compresses screen shots (like VNC), but with xpra you can disconnect and reconnect on different computers. To get the basic functionality you can just type "ssh -X server.location" and any GUI app you open from the command line will open locally. I've been able to get xpra to build by doing the following: Download pari-all-0.0.6.tar.gz from the xpra site listed under upstream and untar it. Issue the following Mac Ports command (Dependencies thanks to RogBlog): sudo port install python25 python26 py26-pyrex py26-gtk xorg-libXtst py25-gobject py25-gtk py25-nose py26-nose xorg-libXdamage xorg-libXcomposite xorg-libXtst xorg-libXfixes In the upstream list of v0.0.06 patches (NOT 0.0.8pre!) on the xpra site listed above, download mswindows-conditional-pyrex.patch. Open the patch with your favorite text editor and change the single occurrence of "win" in it to "darwin". Apply the patch to setup.py. Run do-build in the command line. Now where I'm stumped: how do I run xpra? The build produces a sub directory called install/bin in which xpra is located, but when I try to run it I get the following error: Traceback (most recent call last): File "./xpra", line 4, in import xpra.scripts.main ImportError: No module named xpra.scripts.main There is a file called main.py under xpra/scripts, but I don't know any python and I'm not sure if this is what it's looking for, and what to do with it even if it is. My goal is to set up xpra so I can install it into /usr/bin (or some other common path for executables) and execute it whenever I please. What do I do next?

  Read the article

• Why does clicking on Windows 7 Printer Properties Result In Driver Not Installed?

  - by octopusgrabbus

  The question I need to ask is has anyone heard of getting a "driver not installed" error when clicking on a printer's properties on Windows 7, and is there a workaround? Here are the details of the problem. One of our users has a Windows 7 desktop, and an HP LaserJet 4050 T connected to via a parallel-to-usb converter. The PLC5 universal driver was installed for series 4050 printers. I needed to install the PLC 6 driver, which completed successfully. The user is an administrator of the system, and I was prompted to and accepted running as Administrator to install the driver. After the install, I went to see the 4050's properties and was prompted that the PLC6 driver was not installed. I believe the PLC6 driver was installed, because the PLC5 driver resulted in receiving an official HP error page indicating the printer was "not set up for collating" as the second page of printing two copies of a one page email. This problem did not occur with the PLC 6 driver. Oddly enough, setting back to PLC5 produced the same error about the PLC5 driver not being installed. I ignored/dismissed the error box (did not re-install the driver), and reproduced the error, with the second page being the HP not set up for collating error page. Any thoughts on what is causing this and how to clear it would be appreciated. The closest fix I could find was on a Microsoft tech page, and they had me clear winsock out of a Administrator run command line, followed by a reboot. That did not fix the problem. I have also found this http://social.technet.microsoft.com/Forums/windowsserver/en-US/5101195b-3aca-4699-9a06-db4578614e2d/changing-driver-results-in-printer-driver-is-not-installed-error-on-server-2008?forum=winserverprint and will look into trying some of these suggestions, which appear to me to be a "shotgun" approach to fixing the problem.

  Read the article

• Building vs buying a server for an academic lab [closed]

  - by Roy

  I'm looking for advice on the classic build vs buy question. We need a new linux server to run Matlab computation on in our lab (academic). Matlab parallel computing toolbox licence allows up to 12 local workers so we are aiming at a 12 core server with 4GB memory per core (total of 48gb). The system will have an SSD for the OS and a raid-5 (4x2tb) for data. I looked around and found a (relatively) cheap vendor, Silicon Mechanics, that offers a system to our liking (specs below) for $6732. However, buying the components from newegg cost only $4464! The difference is $2268 which is 50% of the base cost. If buying from a company can be thought of as a sort of insurance, basically my premiums are of 50% of the base cost which to me sounds like a lot. Of course any downtime is bad, but the work is not "mission critical", i.e. if it takes a few days to fix it when it breaks its no the end of the world. If it takes weeks to months then its a problem. If it breaks 2-3 times in 3 years, not too bad. If it breaks every month not good. In term of build experience, I set up a linux cluster in grad school (from existing computers) and I build my home pcs but I never built a server before. The server components I'm thinking about: 1 x SUPERMICRO SYS-7046T-6F 4U Tower Server Barebone Dual LGA 1366 Intel 5520 DDR3 1333/1066/800 ($1,050) 12 x Kingston 4GB 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) ECC Unbuffered Server Memory ($420) 2 x Intel Xeon E5645 Westmere-EP 2.4GHz LGA 1366 80W Six-Core ($1,116) 4 x Seagate Constellation ES 2TB 7200 RPM SATA 6.0Gb/s 3.5" ($1,040) 1 x SAMSUNG Internal DVD Writer Black SATA ($20) 1 x Intel 520 Series 2.5" 180GB SATA III MLC SSD $300 1 x LSI LSI00281 PCI-Express 2.0 x8 MD2 Low profile SATA / SAS MegaRAID SAS 9260CV-4i Controller Card, $695

  Read the article

• How to encourage Windows administrators to pick up scripting

  - by icelava

  When i worked as an administrator in my first job, I was frustrated our administration processes with Windows servers were a series of point-and-clicks; we could never match the level of efficiency with the Unix servers which had a group of shell scripts to automate a lot of the work. I soon read about WSH and ADSI and wasted no time learning just how much automation I was able to achieve with scripting. There was a huge problem though - almost none of my Windows colleagues were really interested in learning scripting. They seemed happy with the manually mouse-clicking chores and were never excited at the prospect of using scripts to do the work on their behalf. I struggled to convince them to pick up scripting skills despite the evident increases in efficiency. I left that job in pursuit of a full-time software development career thereafter. Almost a decade on working in various environments and different customers, I still encounter Windows administrators mainly possessing this general "mood" where they would avoid scripting as much as possible. Despite the increasing level of accessibility Windows server technologies are opening up for scripting and automation. I am almost certain the majority of administrators are administrators precisely because they absolutely hate performing any kind of programming duties. What are some means to encourage and motivate administrators that scripting can really help them in the long run?

  Read the article

• Simple way to set up port knocking on Linux?

  - by Ace Paus

  There are well known benefits of Port Knocking utilities when utilized in combination with firewall IP table modification. Port Knocking is best used to provide an additional layer of security over other tools such as the OpenSSH server. I would like some help setting it up on a ubuntu server. I looked at some port knocking implementations here: PORTKNOCKING - A system for stealthy authentication across closed ports. IMPLEMENTATIONS http://www.portknocking.org/view/implementations fwknop looked good. I found an Android client here. And fwknop (both client and server) is in the ubuntu repos. Unfortunately, setting it up (on the server) looks difficult. I do not have iptables set up. My proficiency with iptables is limited (but I understand the basics). I'm looking for a series of simple steps to set it up. I only want to open the SSH port in response to a valid knock. Alternatively, I would consider other port knocking implementations, if they are much simpler to set up and the desired Linux and Android clients are available.

  Read the article

• How do I enable additional debugging output from Ansible and Vagrant?

  - by Brian Lyttle

  I'm investigating Ansible for server and application provisioning. My application is currently provisioned with shell scripts in Vagrant. Rather than rewrite my scripts I've taken a sample and attempted to deploy it. It appears to deploy fine, but I've seeing a failure message after what looks like a series of successful steps: » vagrant provision ~/vm/blvagrant 1 ? [default] Running provisioner: ansible... PLAY [web-servers] ************************************************************ GATHERING FACTS *************************************************************** ok: [192.168.9.149] TASK: [install python-software-properties] ************************************ ok: [192.168.9.149] => {"changed": false, "item": ""} TASK: [add nginx ppa if it ubuntu 10.04 and up] ******************************* ok: [192.168.9.149] => {"changed": false, "item": "", "repo": "ppa:nginx/stable", "state": "present"} TASK: [update apt repo] ******************************************************* ok: [192.168.9.149] => {"changed": false, "item": ""} TASK: [install nginx] ********************************************************* ok: [192.168.9.149] => {"changed": false, "item": ""} TASK: [copy fixed init for nginx] ********************************************* ok: [192.168.9.149] => {"changed": false, "gid": 0, "group": "root", "item": "", "mode": "0755", "owner": "root", "path": "/etc/init.d/nginx", "size": 2321, "state": "file", "uid": 0} TASK: [service nginx] ********************************************************* ok: [192.168.9.149] => {"changed": false, "item": "", "name": "nginx", "state": "started"} TASK: [write nginx.conf] ****************************************************** ok: [192.168.9.149] => {"changed": false, "gid": 0, "group": "root", "item": "", "mode": "0644", "owner": "root", "path": "/etc/nginx/nginx.conf", "size": 1067, "state": "file", "uid": 0} PLAY RECAP ******************************************************************** 192.168.9.149 : ok=8 changed=0 unreachable=0 failed=0 Ansible failed to complete successfully. Any error output should be visible above. Please fix these errors and try again. How do I go about getting additional debug information? I've already added ansible.verbose = true to my vagrant config which results in the dictionaries being displayed within the output above.

  Read the article

• Laptop authentication/logon via accelometer tilt, flip, and twist

  - by wonsungi

  Looking for another application/technology: A number of years ago, I read about a novel way to authenticate and log on to a laptop. The user simply had to hold the laptop in the air and execute a simple series of tilts and flips to the laptop. By logging accelerometer data, this creates a unique signature for the user. Even if an attacker watched and repeated the exact same motions, the attacker could not replicate the user's movements closely enough. I am looking for information about this technology again, but I can't find anything. It may have been an actual feature on a laptop, or it may have just been a research project. I think I read about it in a magazine like Wired. Does anyone have more information about authentication via unique accelerometer signatures? Here are the closest articles I have been able to find: Knock-based commands for your Linux laptop Shake Well Before Use: Authentication Based on Accelerometer Data[PDF] Inferring Identity using Accelerometers in Television Remote Controls User Evaluation of Lightweight User Authentication with a Single Tri-Axis Accelerometer Identifying Users of Portable Devices from Gait Pattern with Accelerometers[PDF] 3D Signature Biometrics Using Curvature Moments[PDF] MoViSign: A novel authentication mechanism using mobile virtual signatures

  Read the article

• Index a low-cost NAS on Windows 7

  - by JcMaco

  Has anyone found a way to index the files stored on a Networked Attached Storage on Windows 7 so that the files can be available in Windows Search and Libraries? I am referring to the cheap and available NAS like the Western Digital My Book series that use an embedded linux server. Similar question: http://windows7forums.com/windows-7-networking/6700-indexing-nas-drive-libraries.html EDIT Windows help proposes to make the files stored on the NAS available offline. This is obviously not a good solution if the NAS has more data than what the client can store. If the folder is on a network device that is not part of your homegroup, it can be included as long as the content of the folder is indexed. If the folder is already indexed on the device where it is stored, you should be able to include it directly in the library. If the network folder is not indexed, an easy way to index it is to make the folder available offline. This will create offline versions of the files in the folder, and add these files to the index on your computer. Once you make a folder available offline, you can include it in a library. When you make a network folder available offline, copies of all the files in that folder will be stored on your computer's hard disk. Take this into consideration if the network folder contains a large number of files.

  Read the article

• which grabber is good enough to get 1000fps?

  - by user261002

  I have two framegrabber with a fast camera (1800+ fps). can anybody who understand the hardware, explain to me which of the following grabbers can help me more to grab 1000fps ? here are the the features of the two grabbers : Inspecta-5 Full Camera Link® Version: · Support for line scan and area cameras. · Video data rate of up to 660 Mbytes/sec. · PCI – X bus interface for 64 Bit data width and 66 MHz clock frequency. · PCI bus interface for 32 Bit data width and 33 MHz clock frequency. · 2 Gigabyte Onboard Memory for fast video streams. · Four opt coupled input- output ports for external trigger and encoder signals. · 528 Mbytes/sec. maximum data rate on the PCI–X Bus. · SDK for Windows 2000/XP SILICONSOFTWARE V-Series Camera Link : “microEnable IV VD4-CL” · Camera Pixel Clock Support 85 MHz · Area Scan Cameras 32k * 64k max. image size · Line Scan Cameras 64k max. image width · Acquisition Buffer: 512 MB DDR-RAM · Sustainable Transfer Rate (max.) 850 MBytes/sec. · microEnable SDK for Windows XP/Vista/ 7/ Linux

  Read the article

• ProCurve ACL to prevent a subnet from leaving the switch

  - by kce

  I have a single HP ProCurve 2610 in a remote location that is connected in with the rest of the network via SHDSL. There are two Layer-3 networks on this segment. ACLs are setup to deny one subnet (192.0.2.0/24) from ever being able to leave the switch by virtue of being applied to port attached to the upstream connection. The other subnet should be permitted to freely leave the switch. Both subnets are on the same VLAN. Unfortunately SFlow very clearly show broadcast traffic from 192.0.2.0/24 on the upstream connection. ProCurve ACLs are not my strong suit but I feel like I'm missing something very simple here. ip access-list extended "Filter for Camera Network" deny ip 192.0.2.0 0.0.0.255 0.0.0.0 255.255.255.255 log permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 exit interface 24 name "DSL - UPLINK" access-group "Filter for Camera Network" in exit Unless I am mistaken traffic from 192.0.2.0/24 should be dropped as it crosses the uplink port (int 24) whereas all other traffic will be permited by the following default allow rule. What exactly am I missing here? EDIT: Firstly, why do you have two subnets contained in the same VLAN? Because that's how it was configured by a previous administrator and while it makes conceptual sense that a single subnet is "mapped" to a single VLAN there's no technical constraint that I am aware of that makes this have to be the case. Instead of filtering inbound traffic on your uplink, you should be filtering outbound traffic. The HP2600 series can only filter inbound traffic on interfaces. Should I change my filter to deny any to 192.0.2.0/24?

  Read the article

• Windows Server 2008 R2 Virtual Network Setup

  - by jpearl01

  Some background: I'm very much new to networking in general, and virtualization in particular. I'm trying to set up a series of VMs as we are transitioning to a thin client setup. I have been supplied a limited number of static ip addresses. The server is located in an offsite building which houses the network we use to connect to the internet, share folders etc. The setup I've been trying to go for is this: The host OS (Windows Server 2008 R2) is bound to one nic using one of the static ips (say, Nic1 and ip 10.255.6.61). I've set up another external virtual network attached to another physical nic , and a virtual private network attached to no nic. There is one VM running the same os (as the host). This VM is connected to both the external virtual network (and uses another static ip say Nic2 and ip 10.255.6.62) and also to the virtual private network (I gave it a static random ip 192.168.88.1 subnet mask 255.255.255.0). This virtual private network is connected to all the other VMs. I'd like to share the internet connection with all the other VMs on the private virtual network, and so I installed the RRAS role on the server connected to Nic2, and selected the option to share the internet over the vpn. I've run through the RRAS wizard a few times, trying different configurations, but none of them seem to be letting the other vms connect to the 'net. The vms seem to connect to the virtual private network fine, they are assigned an ip address and everything, but no internet, and no rest of the network either. The other problem is in general I connect to the vms with RDP. Will that be possible with a setup like this? i.e. will the vms show up as computers on the network? If not, what are my other options? Thanks! ~josh

  Read the article

• How do I stop linux from trying to mount android phone as usb storage?

  - by user1160711

  When I plug in my Motorola Triumph to my fedora 17 linux box USB port, I get an endless series of errors on the linux box as it desperately attempts to mount the phone as a USB drive. Stuff like this: Jun 23 10:26:00 zooty kernel: [528926.714884] end_request: critical target error, dev sdg, sector 4 Jun 23 10:26:00 zooty kernel: [528926.715865] sd 16:0:0:1: [sdg] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jun 23 10:26:00 zooty kernel: [528926.715869] sd 16:0:0:1: [sdg] Sense Key : Illegal Request [current] Jun 23 10:26:00 zooty kernel: [528926.715872] sd 16:0:0:1: [sdg] Add. Sense: Invalid field in cdb Jun 23 10:26:00 zooty kernel: [528926.715876] sd 16:0:0:1: [sdg] CDB: Read(10): 28 20 00 00 00 00 00 00 04 00 If I go ahead and tell the phone to allow linux to mount the USB storage, the messages stop, and I get a mounted drive, but if all I want to do is use the debug bridge, my log on linux will continue to fill with this junk. Is there some udev magic I can do to make the system ignore this particular device as far as usb storage goes? I just noticed that if I tell the phone to enable USB storage, let linux recognize the new disk, then tell the phone to disable USB storage again, I get one additional log message about capacity changing to zero, but the endless spew of messages stops, so I guess one work around is to enable and disable USB right away.

  Read the article

• Virtual IPv6 Network between VirtualBox VMs

  - by Ben

  I'm trying to create a virtual IPv6 network as a test environment. I have 5 VirtualBox VMs (Ubuntu Server) with network adapters using host-only networking. You can imagine them being connected in series and every machine connects 2 subnets. I want to ping the last machine from the first one: On: 2001:db8:aaaa::100 I want to ping 2001:db8:dddd::101 (Note: there is no cccc network in between) Only static configuration and routes are used: /etc/network/interfaces auto eth0 iface eth0 inet6 static address 2001:db8:aaaa::100 netmask 64 /etc/network/interfaces auto eth0 iface eth0 inet6 static address 2001:db8:aaaa::101 netmask 64 auto eth1 iface eth1 inet6 static address 2001:db8:bbbb::100 netmask 64 up ip -6 route add 2001:db8:dddd::/64 via 2001:db8:bbbb::101 dev eth1 down ip -6 route del 2001:db8:dddd::/64 via 2001:db8:bbbb::101 dev eth1 I thought there might be some automatic route discovery going on. Anyway, ping6 2001:db8:dddd::100 will not work from aaaa::100 When I add the route: ip -6 route add 2001:db8:dddd::/64 via 2001:db8:aaaa::101 it will work. But the next interface in the same network dddd::101 is not reachable. How could that be? There is a machine with an interface bbbb::101 and another dddd::100 and I can ping the latter one, but the machine connected to it, dddd::101 not?? I also have also turned on forwarding. Any ideas?

  Read the article

• All network devices freezing when Airport Extreme Base Station is connected. Any ideas?

  - by Jon

  I've been troubleshooting this issue for a while, and through a series of events have it narrowed down to my airport extreme base station. I like this router, since I'm able to connect to IPV6 sites without any insane configuration (my alternate router is too old and doesn't support v6). My question is: Has anyone else had this issue, if so how is it resolved? If not, can you recommend a good IPv6 router? Here is how I came to the conclusion that it is the router: Devices: XBOX 360, HTC Incredible, Home-Built machine running FreeBSD, Home-Built machine running Ubuntu 10.04. 1.) Noticed freezing on Ubuntu Box. 2.) Noticed freezing on XBOX360 3.) Noticed freezing on HTC Incredible (only when connected to my network wirelessly). The above all happened at random times throughout the past few weeks. Over the last few days, I was playing XBOX and noticed that the XBOX and Ubuntu machines both froze. I picked up my phone, and it was also frozen. I reset all devices, power-cycled my router, and all was fine again. About two hours later, it happened again (I was playing Forza III, the XBOX froze; I went to the Ubuntu box and it was frozen; unfortunately, the HTC phone was not connected wirelessly, and the FreeBSD box was turned off). I can't even begin to imaging what a router could be doing to freeze devices with such differing hardware/software/OS, and I feel absurd for coming to this conclusion, but I have nothing else. I hooked up my archaic Netgear router, and have had no problems since. :(

  Read the article

• How to monitor bandwidth use of each device on wifi network

  - by GWLlosa

  I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• How To Monitor Home Wireless Network Connected Devices Bandwith

  - by GWLlosa

  (Originally posted on SuperUser, not sure if it might be better suited here) I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• Switch Before Firewall / Router - Multiple public IPs

  - by rii

  I currently Have a 10Mbit Full duplex circuit connected to a small unmanaged switch which then connects to a Sonicwall Firewall / Router. I have several public IP addresses (/28) that are assigned to several devices in my setup. Now the problem is the small switch I have was lent to me and needs to be returned, I have replaced this switch with several other switches but for some reason any other switch I use causes the network to become extremely slow. I believe this is a problem with the autonegotiation of theses hubs, so I am thinking of purchasing a small managed switch (cisco 300 series) and making the receiving port on the swith Explicitly 10Mbit Full Duplex and see if this works. My question is, being that this is a managed switch and needs an IP, will I still be able to run my public ips through it? Say the circuit has 70.80.4.1 - 7 will I still be able to assign 70.80.4.2 to my firewall and 70.80.4.3 to my router connected to some other port in the switch? Will I have to assign the switch a public IP address in this range as well for it to "route" to those other devices or does the switch does not care what IPs goes through it while operating as a Layer 2 Switch? Any help would be greatly appreciated. Thanks in advanced!

  Read the article

• Troubleshooting an overheating CPU

  - by Jeff Fry

  I & my father just recently put together a new PC. Specs below. From the very beginning, on boot it will often complain that the CPU is too hot. If I sit in BIOS and watch the CPU, it'll drop back down from red to blue (<72C), at which point I've tended to just boot into Windows...and haven't had any problems. In fact, I've played a couple hours straight of Skyrim at max settings, and not had any visible issues. That said, I've occasionally walked away & come back to find that it's crashed. Yesterday, it crashed (while idle) twice in 12 hours, which shifted the balance from busy-with-life to nervous-I'm-about-to-melt-something. I just installed Core Temp which is showing my 4 cores fluxuating between 70-98C. I'm guessing at this point that the CPU fan may be incorrectly installed or defective. My first thought is to either (a) add water cooling (which the case supports) and / or (b) replace the CPU fan with an after-market one. That said, I'm very open to suggestions. A note, while I certainly don't want to burn money here, I have a baby coming any day now and am still unpacking from a recent move so if I have a choice between an option that costs money and another that takes a while...I'll happily spend a bit extra. Side question: Should I be nervous to even have this on at this point? Let me know if there's something useful I could add to my report. Otherwise, I'm looking forward to your suggestions! Thanks. CPU Intel i7-2600 CPU w/ stock fan Other HW ASUS P8Z68-V Pro motherboard 64G SSD boot drive 4 older SATA HDs GIGABYTE ATI Radeon HD6950 1 GB DDR5 8G Kingston T1 Series RAM Corsair 650W Gold Certified power supply Antec P280 case

  Read the article

• Trouble connecting to a local SQL server instance from the web

  - by dfarney

  We have a small network behind a firewall (WatchGuard XTM 2 series) and network switch. On our network we have multiple instances of SQL server, but 1 in specific that I would like to be able to access remotely from our website. We have a static IP address from our ISP and then all the machines on the network have a locally assigned dynamic IP address. When trying to connect to the database from outside our network how do I get the request to be directed to the proper machine / SQL instance? Is it a parameter in my connection string or something in my firewall? A few things to rule out: 1) The firewall is allowing access from the website to our network. I added the site's IP and opened up port 1433. Also, when trying to connect and monitoring the firewall no exceptions come up as they did before I added the proper IP address. 2) Remote connections on the SQL server has been setup and enabled. I've done a lot of reading up on remote connections and I am sure it has been setup properly. I am currently getting this error message on my site: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: TCP Provider, error: 0 - A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.)

  Read the article

< Previous Page | 143 144 145 146 147 148 149 150 151 152 153 154  | Next Page >