Search Results

Search found 5226 results on 210 pages for 'pg hba conf'.

Page 149/210 | < Previous Page | 145 146 147 148 149 150 151 152 153 154 155 156  | Next Page >

• Installing nvidia drivers causes computer to boot to command prompt.

  - by levesque

  Hi, I have an Asus u30jc laptop, which comes with the Optimus prime graphics card switching technology that is now supported under 2.6.35, so I decided to give it a try. First I made sure the discrete graphics card was activated and then I installed the drivers proposed by the ubuntu software repository (nvidia-current). However, after rebooting all I got was a command prompt. My graphics card is a nvidia 310M. This is on Ubuntu 10.10 64 bits. What can I do to diagnose/identify the source of this problem? UPDATE: The messsages in my syslog tell me to check the xorg log: Oct 11 12:42:59 u30jc-test gdm-binary[1095]: WARNING: GdmDisplay: display lasted 0.053144 seconds Oct 11 12:42:59 u30jc-test gdm-simple-slave[1450]: WARNING: Unable to load file '/etc/gdm/custom.conf': No such file or directory Oct 11 12:42:59 u30jc-test gdm-binary[1095]: WARNING: GdmDisplay: display lasted 0.038176 seconds Oct 11 12:42:59 u30jc-test gdm-binary[1095]: WARNING: GdmLocalDisplayFactory: maximum number of X display failures reached: check X server log for errors Which I did. I found this message in my /var/log/Xorg.0.log : Fatal server error: [ 113.540] no screens found [ 113.540] What does that mean?

  Read the article

• Yoga Pro 2 Wi-Fi not working

  - by user293004

  I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

  Read the article

• bluetooth daemon not running at startup

  - by ffaxer

  I'm trying to connect a bluetooth mouse to my Xubuntu system using Blueman (v. 1.21) Problem seems to be bluetoothd not running at startup, so blueman refuses to start, only a dialog appears: "Bluez daemon is not running, blueman-manager cannot continue." On my system, bluetoothd will run only as root (sudo), so my current workaround is simply to sudo bluetoothd manually, which works fine but id like to have it run at startup so that my mouse is just working without any interaction from me, if possible. If i try to start bluetoothd as non-root it reports: Bluetooth deamon 4.91 Unable to get on D-Bus In the startup scripts i found the same bluetoothd script in all runlevels and init.d: DAEMON=/usr/sbin/bluetoothd test -f /usr/sbin/bluetoothd || exit 0 # bluetoothd normally starts up by udev rules. it needs dbus to function, log_progress_msg "bluetoothd" pkill -TERM bluetoothd || true log_progress_msg "bluetoothd" I looked in /etc/udev/rules.d/ but no reference to bluetoothd. Further i have already tried with no luck: Editing /etc/dbus-1/system.d/bluetooth.conf to include my user (essentially copying the part that was for root): I tried it while both keeping the root policy and without, still, no luck! Editing /etc/pam.d/common-session and /etc/pam.d/gdm to include the line: session optional pam_ck_connector.so In the case of common-session it was already there but with a "nox11" which i tried removing. No luck no luck. Btw, I'm confused as to which session manager I'm using, since i have both xfce4-session and gdm-session-worker running. Anyways, hope someone is savvy enough to figure it out or bring some hints, otherwise i sincerely apologize for wasting your time! I'll sign off with uname -a: Linux [mycompname] 3.0.0-9-lowlatency #12ppa1~natty1-Ubuntu SMP PREEMPT Mon Aug 22 06:52:15 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux Peace B)

  Read the article

• Problem connecting to isp server using xl2tpd as client. Ubuntu server 13.04

  - by Deon Pretorius

  I have followed guides found on google and ubuntu support pages and can get xl2tpd connection up but only under the following conditions: 1 - ADSL model must be configured and connected to the ISP or 2 - ADSL modem in bridge mode I must have an existing PPPoe connection established. If neither of the above are active xl2tpd wont trigger pppd and connect to the isp and thus tunnel connection fails to connect to the L2TP server of the ISP. Am I doing something wrong; /etc/ppp/options.l2tpd.axxess ipcp-accept-local ipcp-accept-remote refuse-eap refuse-chap require-pap noccp noauth idle 1800 mtu 1200 mru 1200 defaultroute usepeerdns debug lock connect-delay 5000 name (name used for ppp connection) /etc/ppp/pap-secrets # * password (name used for ppp connection as above) * (ppp password supplied by isp) /etc/xl2tpd/xl2tpd.conf [global] ; Global parameters: auth file = /etc/xl2tpd/l2tp-secrets ; * Where our challenge secrets are access control = yes ; * Refuse connections without IP match debug tunnel = yes [lac axxess] lns = 196.30.121.50 ; * Who is our LNS? redial = yes ; * Redial if disconnected? redial timeout = 5 ; * Wait n seconds between redials max redials = 5 ; * Give up after n consecutive failures hidden bit = yes ; * User hidden AVP's? length bit = yes ; * Use length bit in payload? require pap = yes ; * Require PAP auth. by peer require chap = no ; * Require CHAP auth. by peer refuse chap = yes ; * Refuse CHAP authentication require authentication = yes ; * Require peer to authenticate name = BLA85003@axxess ; * Report this as our hostname ppp debug = yes ; * Turn on PPP debugging pppoptfile = /etc/ppp/options.l2tpd.axxess ; * ppp options file for this lac /etc/xl2tpd/l2tp-secrets # Secrets for authenticating l2tp tunnels # us them secret # * marko blah2 # zeus marko blah # * * interop * vzb_l2tp (*** secret supplied by isp) ^ isp server host name Any help will be greatly appreciated

  Read the article

• Intel graphic chipset and NVIDIA Geforce GTX560

  - by antoine

  I have an NVIDIA Geforce GTX560 with two video projectors and I would like to use the onboard Intel Graphic Chipset to plug an additional monitor. I saw the question : How can I use both Intel onboard and Nvidia graphics at the same time? but the answer is so short that I was not convinced. My motherboard (GIGABYTE GA-H61M-D2P-B3 (rev. 1.0)) equipped with Intel H61 Chipset allow shared memory between onboard and PCIe cards. And Windows 7 allow me to use the three outputs thanks to Intel's driver. I'm able to use the onboard graphic card but without graphical interface for now. I think i need intel driver for that. But I would like to know if I can setup my displays in xorg.conf with something like : Section "Device" Identifier "Device0" Driver "intel" EndSection Section "Device" Identifier "Device1" Driver "nvidia" EndSection Section "Device" Identifier "Device2" Driver "nvidia" EndSection Does anyone have successfully setup something like that ? Or should I burn my head experimenting it by myself ? Or is there any good reasons to discouraged me to try ? Thanks for your help. Antoine PS : i'm using Ubuntu 10.10 for now, but I could switch to another version. PS2 : i also read this : Use 3 monitors w/built-in intel adapter + two old nvidia PCI cards on 10.10? which doesn't tell me more about the possibilities to use Intel Graphic and Nvidia at the same time EDIT : according to that : Can not get Dual Monitors to work on Different GPUs, I should be able to run two Xserver one on Intel the other on Nvidia. I will try and post the result here.

  Read the article

• XSF-FO intellisense and national languages with Apache FOP

  - by Lukasz Kurylo

  Some time ago I showed how to get an intellisense and how to configure the FO.NET to acquire national characters inside the generated pdf files. Due to the limitations that I mensioned in my previous post, I started playing with the Apache FOP. In this post I want to show, how to acquire the same result as I showed in the two posts related to FO.NET.   Intellisense   To get the intellisense from the XSL-FO templates set the xsi:schemaLocation the same way I showed it in this post. The only diffrence to FO.NET is that, during generating the document by the code I showed last time we will get an exception:   org.apache.fop.fo.ValidationException: Invalid property encountered on "fo:root": xsi:schemaLocation (See position 6:11)   Fortunatelly there is a very easy way to resolve this without removing the entire attribute along with the intellisense. Add to the FopFactory the ignoreNamespace by:   FopFactory fopFactory = FopFactory.newInstance(); fopFactory.ignoreNamespace(http://www.w3.org/2001/XMLSchema-instance);   Notice that, the url specified in this method this is a namespace for the xmlns:xsi namespace, not xsi.schemaLocation.   Fonts / national characters   This point is a little dfferent to acquire, but not more complicated that it was with FO.NET. To set the fonts in Apache FOP 1.0, we need a configuration file. A sample one can be get from the directory where we unpacked the fop binaries, from conf subdirectory. There is a file called fop.xconf. We must copy this file to our solution. In the simplest way, in the <fonts> tag we can add  <auto-detect/>. Thanks to this, FOP will index all fonts available on the installed operating system. There probably should be no problem, if we have a http handler or a WCF Service on the server that serves the generated pdf documents. In this situation we can use all available fonts on this server.   To use this config file, we must set a path to it:   FopFactory fopFactory = FopFactory.newInstance(); fopFactory.setUserConfig(new File("fop.xconf"));

  Read the article

• Higher resolutions unavailable with 2.6.38-8 kernel

  - by time-wastrel

  After upgrading to Natty and the 2.6.38-8 kernel I could no longer obtain the 1920x1080 resolution available in Maverick with 2.6.35-22. In fact the boot occasionally hung. However, after selecting the remaining 2.6.35-22 kernel, the high resolution was available. I then made the mistake of completely reinstalling, but could never get the higher resolutions with 2.6.38-8, no matter what I did. e.g. trying the nvidia proprietary driver, creating an xorg.conf. Even from the command line using xrandr --newmode "1920x1080_60.00" 173.00 1920 2048 2248 2576 1080 1083 1088 1120 -hsync +vsync xrandr --addmode DVI-I-1 1920x1080_60.00 xrandr --output DVI-I-1 --mode 1920x1080_60.00 all I would get would be a blank screen and the monitor reporting no input. (Low resolutions displayed fine with xrandr.) I could actually add the 1920x1080 to the already existing probe-reported resolutions in the pool of available resolutions, but choosing it would give the blank screen. In the end I installed the 2.6.35-22 kernel again. The high resolution is back. For a while there, staying up all night and trying many things, I thought that a new video board or monitor might be needed, but deep down, I knew that they were both OK. My question is - "Is this some bug involving the latest kernel, that will go away, or if this persists in future kernels, is there a way to make sure that I can keep my native resolution?"

  Read the article

• Unable to access any ubuntu shares from android/windows clients

  - by dan

  I am running Ubuntu 11.04, and cant seem to access any of my shares. Here is the output from testparm-s : Load smb config files from /etc/samba/smb.conf rlimit_max: increasing rlimit_max (1024) to minimum Windows limit (16384) Processing section "[printers]" Processing section "[CanonMG2100AIO]" Processing section "[FreeAgent Drive]" Loaded services file OK. WARNING: You have some share names that are longer than 12 characters. These may not be accessible to some older clients. (Eg. Windows9x, WindowsMe, and smbclient prior to Samba 3.0.) Server role: ROLE_STANDALONE [global] server string = %h server (Samba, Ubuntu) encrypt passwords = No obey pam restrictions = Yes pam password change = Yes passwd program = /usr/bin/passwd %u passwd chat = Enter\snew\s\spassword:* %n\n Retype\snew\s\spassword:* %n\n password\supdated\ssuccessfully . username map = /etc/samba/smbusers unix password sync = Yes syslog = 0 log file = /var/log/samba/log.%m max log size = 1000 name resolve order = wins lmhosts host bcast dns proxy = No wins support = Yes usershare allow guests = Yes panic action = /usr/share/samba/panic-action %d [printers] comment = All Printers path = /var/spool/samba create mask = 0700 guest ok = Yes printable = Yes browseable = No [CanonMG2100AIO] comment = Printer Drivers path = /var/lib/samba/printers read only = No guest ok = Yes [FreeAgent Drive] path = /media/FreeAgent Drive read only = No guest ok = Yes smbtree: Server requested plaintext password but 'client plaintext auth' is disabled anonymous failed session setup with NT_STATUS_INVALID_PARAMETER Server requested plaintext password but 'client plaintext auth' is disabled anonymous failed session setup with NT_STATUS_INVALID_PARAMETER and hostname: dekstop I know the spelling of desktop is incorrect. it was a duh moment. Any help would be greatly appreciated.

  Read the article

• Why is Ubuntu offline (except torrents) while Windows is online?

  - by Fahim al Islam

  I am using a static wired connection. Everything was perfect. But suddenly from few hours back I can't access any website. Dropbox, Ubuntu One also can't connect. Ping request is also unsuccessful, but I can download through torrent. I am not trying torrent download and browsing at the same time. So, I think it's not an issue about torrent using all the bandwidth. One important point is that this connection works perfectly on Windows on this same PC (My PC is dual-boot). I have tried the way what izx has suggested (using "sudo sh -c 'echo nameserver 8.8.8.8 /etc/resolv.conf'"), but I'm facing the same problem again. Now I can't even ping 8.8.8.8 and google.com. Though I can ping 74.125.228.2 (which is Google IP address) I can't understand what's happening and why this is happening. I'm new in this website many rules and regulations is unknown to me. So, please don't be bothered for my mistakes. Looking forward for help from anyone. Thanks to all.

  Read the article

• After login I only get a terminal window

  - by Ambidex

  First of, let me tell you I'm a n00b at ubuntu. I have updated my Ubuntu mediacenter to a later version of ubuntu, currently at 12.04. I'm working through a lot of updates to get to the latest. But since my first update I got the new login screen (lightdm?) and my autologin wasen't working anymore. So I Googled how I could make lightdm autologin. I've managed this by making my /etc/lightdm/lightdm.conf look as follows: [SeatDefaults] greeter-session=unity-greeter user-session=ubuntu autologin-user=my_user autologin-userutologin-user=-timeout=0 Which seemed to work... But now that it automatically logs in, I seem to get the following type of screen (through nomachine remote desktop client): Sorry... I am unable to post my screenshot here because I do not have the 10 reputation points in askubuntu yet.... darn it... But the screen has a terminal at the top left of the screen (not an actual "window"), and the ubuntu loading screen is still behind it. I've tried running startx as you can see. But, this seems to actually be x server. But if I run unity --reset, it seems that a lot of the desktop gets restored, but... with a lot of errors and warnings and the next time I boot, it's the same story all over again. Also, when I close the terminal window after getting my desktop back, I get thrown back at the login screen. Please bear with my lack of knowledge of ubuntu and it's underlying unix. I thank you in advance.

  Read the article

• Killing a Plesk 11.5 backup process in Ubuntu

  - by Klaaz

  I want to kill a backup process initiated by Plesk in Ubuntu but don't know which processes safely can be killed: ps aux | grep backup root 20505 0.0 0.0 4392 604 ? Ss 01:43 0:00 /bin/sh -c [ -x /opt/psa/admin/sbin/backupmng ] && /opt/psa/admin/sbin/backupmng >/dev/null 2>&1 psaadm 20510 0.0 0.0 30884 1816 ? S 01:43 0:00 /opt/psa/admin/sbin/backupmng psaadm 20511 0.0 0.0 30884 644 ? S 01:43 0:01 /opt/psa/admin/sbin/backupmng psaadm 20512 0.0 0.6 270472 49356 ? S 01:43 0:03 /usr/bin/sw-engine -c /opt/psa/admin/conf/php.ini /opt/psa/admin/plib/backup/scheduled_backup.php --dump 1 root 20517 0.0 14.9 1400124 1214696 ? SN 01:43 0:27 /usr/bin/perl /opt/psa/admin/bin/plesk_agent_manager server --owner-uid=0bd9576c-f832-4362-b4f4-3c1afac22be2 --owner-type=server --dump-rotation=7 --backup-profile-name=serverXL_ --session-path=/opt/psa/PMM/sessions/2013-10-23-014303.864 --output-file=ftp://[email protected]//backup/serverXL/ --ftp-passive-mode root 27423 0.0 0.0 13652 888 pts/2 S+ 10:35 0:00 grep --color=auto backup root 29103 1.0 14.8 1400124 1209760 ? SN 02:16 5:21 /usr/bin/perl /opt/psa/admin/bin/plesk_agent_manager server --owner-uid=0bd9576c-f832-4362-b4f4-3c1afac22be2 --owner-type=server --dump-rotation=7 --backup-profile-name=serverXL_ --session-path=/opt/psa/PMM/sessions/2013-10-23-014303.864 --output-file=ftp://[email protected]//backup/serverXL/ --ftp-passive-mode root 29106 0.0 14.8 1400404 1212456 ? DN 02:16 0:07 /usr/bin/perl /opt/psa/admin/bin/plesk_agent_manager server --owner-uid=0bd9576c-f832-4362-b4f4-3c1afac22be2 --owner-type=server --dump-rotation=7 --backup-profile-name=serverXL_ --session-path=/opt/psa/PMM/sessions/2013-10-23-014303.864 --output-file=ftp://[email protected]//backup/serverXL/ --ftp-passive-mode It seems the FTP process is the culprit?

  Read the article

• Problems with wired ethernet connection Ubuntu 11.10

  - by Andrew Fielden

  After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

  Read the article

• Is a disk/ata timeout exception dangerous?

  - by j-g-faustus

  I have a few hard drives in mdadm RAID 5 configured to go to standby after a few minutes of inactivity. (Using hdparm.conf spindown_time.) At irregular intervals I get messages like these in dmesg: [ 1840.251661] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1840.251722] ata4.00: failed command: SMART [ 1840.251758] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [ 1840.251759] res 40/00:14:50:2e:04/00:00:02:00:00/40 Emask 0x4 (timeout) [ 1840.251858] ata4.00: status: { DRDY } [ 1840.251888] ata4: hard resetting link [ 1840.600742] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1840.601521] ata4.00: configured for UDMA/133 [ 1840.601547] ata4: EH complete [337877.713988] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [337877.714019] ata4.00: failed command: SMART [337877.714038] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [337877.714039] res 40/00:04:90:10:81/00:00:00:00:00/40 Emask 0x4 (timeout) [337877.714089] ata4.00: status: { DRDY } [337877.714107] ata4: hard resetting link [337878.063085] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [337878.063743] ata4.00: configured for UDMA/133 [337878.063764] ata4: EH complete I think the exception is caused by smartd when a drive does not wake up quickly enough. There are no issues (that I can tell) in accessing the drives normally through the file system - it takes a few seconds longer than normal when they are asleep, but there are no exceptions. Is this something I should worry about, as a potential symptom on something that could corrupt a drive over time? Or can I safely ignore it as part of normal operation? Edit: By request: smartctl -a for sdaand sde, both disks are members of the array. If ata4is the same as scsi-4 then sde is the one that gave the error above, according to /dev/disk/by-path.

  Read the article

• VLC Ati Radeon 6870 Ubuntu 12.04 image skewed flicker

  - by Aaron

  I'm running Ubuntu 12.04 with ATI Radeon 6870 connected to my 40' Sharp TV. The video image is slightly jigged, like breaking a bit and slightly delayed. It just isn't smooth. The computer is very fast, like i7 with 12gb ram. I tried to run the same video with my mac laptop and on the tv with the same connection cable and it was running smoothly. i tried changing the video output in VLC to x11, increase caching, h264 skip loop filter to all, increase monitor refresh rate although it's already at 60 and it's an LCD tv. this is my xorg.conf : Section "ServerLayout" Identifier "amdcccle Layout" Screen 0 "amdcccle-Screen[3]-0" 0 0 EndSection Section "Module" Load "glx" EndSection Section "Monitor" Identifier "0-DFP9" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" Option "PreferredMode" "1920x1080" EndSection Section "Monitor" Identifier "0-DFP10" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1280x1024" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Device" Identifier "amdcccle-Device[3]-0" Driver "fglrx" Option "Monitor-DFP9" "0-DFP9" BusID "PCI:3:0:0" EndSection Section "Screen" Identifier "Default Screen" DefaultDepth 24 EndSection Section "Screen" Identifier "amdcccle-Screen[3]-0" Device "amdcccle-Device[3]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

  Read the article

• Recovering data from /

  - by Abhijit Gavas

  I accidentally installed Ubuntu to one of my data drives from Windows. The drive was a NTFS drive and contained about 80 GB of important data. The size of the drive is 110 GB. Its new file system is ext4. In an attempt to recover the data, I downloaded foremost and tried the following commands: foremost -i / -o /media/281C8DB01C8D7998/Recovery/ -T -v foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v (sda7 is the drive in question.) It appears that with either command, foremost gets stuck reading some file. Here is the console output: abhi@abi-PC:/dev$ foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v Foremost version 1.5.7 by Jesse Kornblum, Kris Kendall, and Nick Mikus Audit File Foremost started at Fri Sep 28 20:58:00 2012 Invocation: foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v Output directory: /media/281C8DB01C8D7998/Recovery_Fri_Sep_28_20_58_00_2012 Configuration file: /etc/foremost.conf Processing: stdin |------------------------------------------------------------------ File: stdin Start: Fri Sep 28 20:58:00 2012 Length: Unknown Num Name (bs=512) Size File Offset Comment Killed As you can see I have to kill it from system monitor. This approach does not seem to be working. What else could I try to recover the files? Please help. The files are very important and I will be devastated if I cannot recover them.

  Read the article

• NVIDIA Graphics - resolution problems with new 12.04 LTS installation

  - by Daveisuser56810

  I've been trying to install Ubuntu 12.04 LTS on my desktop most of the day. The desktop uses a NVIDIA GEFORCE 9800 (GT I think) graphics card. I am unable to set the correct resolution (1680 x 1050) for the display. The first problem I had was that of the "Black Screen" during install. I overcame this by utilising the "nomodeset" switch on the install options (once I'd found how to do that). The second problem of course was the "Black screen" following the first reboot. Once again this was overcome by using "nomodeset", this time by "editing" the GRUB. This gave me a resolution of 1280x768 which, the Displays GUI allowed me to change to 1280x720 (appears to fit on screen). I then tried to install the NVIDIA drivers. 1) using additional drivers 2) manually by downloading driver and installing in root As soon as NVIDIA drivers are installed - resolution become restricted to 640x480 (max). At this resolution Ubuntu GUI is not usable as most screens are larger than the display. Removing the NVIDIA driver and removing the XORG.CONF file does not lift this restriction. I have tried most things that I have found and that were vaguely intelligible, but nothing appears to get me closer to a resolution of 1680x1050. UPDATE: reinstalled Ubuntu 12-04 and used the "NoModeSet" in the Grub to restore the resolution to 1280x720, which is at least usable. Will live with this for now.

  Read the article

• Connecting to wireless networks from command line

  - by Balaji

  I need to write a shell script which connects to one of the two available wi-fi connections. One is a un secure connection and the other is secure connection. My question has 2 parts- 1.How to connect to the un-secure (un-encrypted and no password required) connection from command line (or by executing a shell script) when I'm connected to the secure connection? I followed the steps in http://www.ubuntugeek.com/how-to-troubleshoot-wireless-network-connection-in-ubuntu.html for in-secure connection. I put all the commands in a script and executed it (I made sure that interface name and essid are correct) - sudo dhclient -r wlan0 - sudo ifconfig wlan0 up - sudo iwconfig wlan0 essid "UAPublic" - sudo iwconfig wlan0 mode Managed - sudo dhclient wlan0 But nothing happens - I'm not disconnected from the current network and connected to the new one 2.When I want to connect to the secure wi-fi network, I understand from http://askubuntu.com/a/138476/70665 that I need to use wpa_supplicant. But I enter a lot of details in the interface when I connect via UI security : wpa and wpa2 enterprise Authentication : PEAP CA certificate : Equifax... PEAP version : automatic inner authentication : MSCHAPv2 username : password : How to use wpa_supplicant to mention all these details in the command line? The conf file network={ ssid="ssid_name" psk="password" } doesn't work for me.

  Read the article

• Screen resolution stuck at 1024x768

  - by Dananjaya

  I just updated from Ubuntu 10.10 to 11.04 and have an issue regarding the screen resolution. I have Intel integrated gfx chip and my monitor supports resolutions larger than 1024x768. (in 10.10 I've been using 1280x1024) But as soon as I upgraded, I'm stuck with 1024x768 resolution and seems I can't change it. running xrandr In terminal yields the following results, Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 LVDS1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1280x800 58.1 + 1024x768 60.0* 800x600 60.3 56.2 640x480 59.9 VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 344mm x 194mm 1366x768 59.9 + 1360x768 60.0 1024x768 75.1 72.0 70.1 60.0* 832x624 74.6 800x600 72.2 75.0 60.3 56.2 640x480 72.8 75.0 66.7 60.0 720x400 70.1 1280x1024_60.00 (0xce) 109.0MHz h: width 1280 start 1368 end 1496 total 1712 skew 0 clock 63.7KHz v: height 1024 start 1027 end 1034 total 1063 clock 59.9Hz What maybe the problem? Is it a bug? What kind of steps I should take in order to get a higher resolution? (changing xorg.conf maybe?) Any insight is highly appreciated. Thanks in advance. UPDATE Screenshot after running xrandr --addmode VGA1 1360x768 As you can see, side bar is not completely visible and Ubuntu logo at the task bar is missing. Also when you open an application, the Task bar of the application (where it should go to the top panel) is missing as well..

  Read the article

• Static IP Address on Ubuntu 12.04 Virtual Machine

  - by chrisnankervis

  I've setup a VM running Ubuntu 12.04 specifically for local web development and am having some problems ensuring it has a static IP address. A static IP address is important as I'm using the IP address in my hosts file to assign a .local suffix to addresses used both in browser and to connect to the correct database on the VM. Currently, every time I connect to a new network or my VM is assigned a new IP address I need to reconfigure my whole environment which is becoming quite a pain. It also probably doesn't help that the default-lease-time on the Ubuntu VM is set to 1800 by default. At the moment I'm using VMWare Fusion and the Network Adapter is enabled and set to "Autodetect" under Bridged Networking. I've tried to set a static IP address within the dhcpd.conf using the code below: host ubuntu { hardware ethernet 00:50:56:35:0f:f1; fixed-address: 192.168.100.100; } The fixed-address that I've used is also outside the range specified in the subnet block (which in this case is 192.168.100.128 to 192.168.100.254). I've tried adding and removing the network adapter and restarting my Mac after each time to no avail. Below is an ifconfig of the VM that might be of some help: eth0 Link encap:Ethernet HWaddr 00:50:56:35:0f:f1 inet addr:192.168.0.25 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fe35:ff1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1624 errors:0 dropped:0 overruns:0 frame:0 TX packets:416 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:147348 (147.3 KB) TX bytes:41756 (41.7 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Are there any specific issues with 12.04 that I'm missing? Otherwise has anyone else got any ideas? Thanks in advance.

  Read the article

• Unable To Get Sound Working to External Speaker on HP TouchSmart 320 on 11.04 or 11.10

  - by Schof

  This is an HP TouchSmart 320, model number 320-1200m. I'm using Ubuntu 11.04. Hardware information: root@hp320:/home/mpower# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Generic [HD-Audio Generic], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 root@hp320:~$ cat /proc/asound/card0/codec#0 | grep Codec Codec: IDT 92HD91BXX Sound to headphone jack works properly, but sound to built-in speakers does not work. I have installed Windows, and with Windows 7 installed, all audio hardware works properly, so this isn't a hardware fault. I've looked at https://help.ubuntu.com/community/HdaIntelSoundHowto and have been unable to find my card in http://www.kernel.org/doc/Documentation/sound/alsa/HD-Audio-Models.txt . I have tried adding almost every conceivable model in the line "options snd-hda-intel model=MODEL" line I added to /etc/modprobe.d/alsa-base.conf. Update 2011-11-09 2:31 PM PST: I've gone to Control Center - Sound Preferences to attempt settings that make sound work. The "Hardware" tab shows one device: "Internal Audio 1 Output / 1 Input Analog Stereo Duplex." There are two output profiles listed in the selection box at the bottom of the tag: Analog Stereo Duplex and Analog Stereo Output. Neither cause sound to emit from the speakers. I've also run alsamixer on the command-line and ensured that everything is set to maximum and nothing is muted. Update 2011-11-09 5:15 PM PST: I've replicated the exact same symptoms in 11.10. Update 2011-11-10 11:31 AM PST: I've filed a bug in launchpad: https://launchpad.net/ubuntu/+source/alsa-driver/+bug/888703

  Read the article

• Configuring Samba to allow Use of CUPS printer

  - by Skizz

  Having trouble with samba printing. I have a CUPS printer installed on an Ubuntu 11.04 server and that works great. When I try to configure samba to allow an XP machine to use the printer, it fails when printing. I can install the printer drivers for XP from the server and the printer appears in the XP printer control panels. When I try to print a test page from the XP machine I get this error in the system event log: Jun 27 20:33:29 FatController smbd[3571]: [2012/06/27 20:33:29, 0] rpc_server/srv_netlog_nt.c:603(_netr_ServerAuthenticate3) Jun 27 20:33:29 FatController smbd[3571]: _netr_ServerAuthenticate3: netlogon_creds_server_check failed. Rejecting auth request from client JAMES machine account JAMES$ Here's my smb.conf file: [global] server string = %h (Server) workgroup = SODOR encrypt passwords = true security = user os level = 255 preferred master = yes domain master = yes local master = yes logon path = \\%L\profile\%U logon drive = S: logon home = \\%L\home\%U domain logons = yes map to guest = Never guest ok = no dns proxy = no time server = yes logon script = logon.bat load printers = yes printing = cups printcap name = cups nt acl support = no interfaces = eth1 lo bind interfaces only = yes smb ports = 445 [netlogon] comment = Net Log On path = /home/samba/netlogon guest ok = no read only = yes browseable = no [profile] comment = User Profiles path = /home/samba/profiles read only = no create mask = 0600 directory mask = 0700 browseable = no store dos attributes = yes [printers] comment = All Printers path = /var/spool/samba browseable = yes guest ok = no printable = yes [print$] comment = Printer Drivers path = /var/lib/samba/printers browseable = yes guest ok = no read only = yes write list = root, skizz Anyone know what the problem is and how to fix it? In addition to the above, I also get this error: Jun 27 21:56:35 FatController smbd[3571]: [2012/06/27 21:56:35, 0] printing/print_cups.c:1027(cups_job_submit) Jun 27 21:56:35 FatController smbd[3571]: Unable to print file to `Edward' - client-error-not-authorized which I think is more relevant.

  Read the article

• Ubuntu 12.04LTS stuck at login mouse and keyboard not responding

  - by user169954

  I have Ubuntu 12.04LTS installed on a dual-booted machine (i5 dual core 8G ram) and it's been working fine, but today for some reason when I logged out and tried to log back in it is stuck at the login page, i.e. the mouse and the keyboard are not responding. The mouse is stuck at the top left corner of my screen, and I can do nothing but to turn the machine off. (I have been using logitech wireless mouse and keyboard.) I can not access the virtual console (Alt-F1 or Cntrl-Alt-F1) either! Here is what I have tried so far: Verified it is not a H/W problem since the mouse and keyboard work fine with windows7 Booted with ubuntu installation dvd and ran trial mode and mouse and keyboard worked fine. Tried bypassing the login screen by booting into recovery mode and editing tty1.conf, but to no avail. I moved .Xauthority .profile and .bashrc from my $HOME to another location so my login would proceed completely by system defaults. But this did not help From recovery mode commandline used to dpkg-reconfigure to switch between gdm and lightgdm. This did not help either. By the way, when in recovery mode as root from command line I mount the filesystem, all apps work fine. Python is Ok, octave is ok, vi is ok etc. I have a feeling if I could only bypass the login screen, and automatically get into the desktop, I will be ok. But I haven't been able to accomplish this either. I desperately need help please. Thank you in advance. Update: So I tried to switch to lightdm by dpkg-configure lightdm. This at least brings me up to the classical linux commandline login prompt but without a gui. Should I install startx? Should I install ubuntu-desktop?

  Read the article

• Need to run a .sh as root on boot or login

  - by Graymayre

  Still new with linux and running ubuntu 12.10 I have a wireless stick (ae2500) which has known issues that has been partially solved using ndiswrapper. However, to use it I must run the same scripts every time I reboot, effectively uninstalling and reinstalling the driver. I made a .sh file to run every time to make it easy, but I must do the sudo login everytime. There are three solutions I am looking for and although not all are necessary to solve this particular problem, I would still like to know them all for learning purposes. run scripts or file.sh on boot (as well as other programs) run scripts or file.sh automatically with root privileges make the install permanent so as not to have to go through the process every time. Any additional information that can help me regarding this that I did not think to ask (including streamlining my commands), or general knowledge, would be greatly appreciated. Following are the contents of the file. I pretty much just made it as I would have entered it. cd ~/ndiswrapper-1.58rc1 sudo modprobe -rf ndiswrapper sudo rm /etc/modprobe.d/ndiswrapper.conf sudo rm -r /etc/ndiswrapper/* sudo depmod -a sudo make uninstall sudo make sudo make install sudo ndiswrapper -i bcmwlhigh5.inf ndiswrapper -l sudo modprobe ndiswrapper

  Read the article

• A "tinkered" PC can ping by IP, not by hostname. How to fix?

  - by aitchnyu

  Like this: root@tis-server:~# ping www.google.com ping: unknown host www.google.com root@tis-server:~# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=55 time=50.3 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=55 time=65.4 ms It was tinkered by somebody else and I (and him!) cant trace his actions. The graphical connection manager also refuses to work thanks to the tinkering. It also makes route add default gw 192.168.0.1 necessary for each reboot to atleast ping by IP. How do I fix this? It is Ubuntu 11.10 As requested: Output of ifconfig: eth0 Link encap:Ethernet HWaddr 48:5b:39:ae:21:98 inet addr:192.168.0.100 Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::4a5b:39ff:feae:2198/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13194 errors:0 dropped:0 overruns:0 frame:0 TX packets:5156 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1420596 (1.4 MB) TX bytes:827295 (827.2 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4817 errors:0 dropped:0 overruns:0 frame:0 TX packets:4817 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:377732 (377.7 KB) TX bytes:377732 (377.7 KB) Output of resolv.conf: Output of /etc/network/interfaces: GNU nano 2.2.6 File: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.100 netmask 255.255.255.0

  Read the article

• There's IP but can't reach gateway

  - by icky

  I have just installed ubuntu 12.04 on my new laptop, and brought it back to home, but I found the wireless network does not work. Strangely, it has the correct ip, but can't connect to the gateway. ifconfig gives ip 192.168.64.36, with broadcast 192.168.79.255 and mask 255.255.240.0, this are all correct, the gateway is at 192.168.64.1 cat /etc/resolv.conf nameserver 192.168.64.1 nameserver 127.0.0.1 which i think it's also right. but when I ping 192.168.64.1, all packages are lost. Please help me with this, I really do not know what happened to my network settings. Huckle, Thank you for your reply ifconfig wlan0 Link encap:Ethernet Hwaddr 88:f9:af:2a:ca:1b inet addr:192.168.64.36 Bcast:192.168.79.255 Mask:255.255.240.0 inet6 addr: fe80::8a9f:faff:fea2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3950 TX byetes:60288 iwconfig wlan0 IEEE 802.11bgn ESSID:"Chiono" Mode:Managed Frequency:2.417 GHz Access Point: 82:54:99:94:6D:43 Bit Rate=13.5 Mb/s Tx-Power=13 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=70/70 Signal Level=-32 dBm Rx invalid nwid:0 Rx invalid crypt:0 RX invalid frag:0 Tx excessive retries: 9 Invalid misc:10 Missed beacon:0 route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.64.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.64.0 * 255.255.240.0 U 2 0 0 0 wlan0 Thank you very much

  Read the article

< Previous Page | 145 146 147 148 149 150 151 152 153 154 155 156  | Next Page >