Search Results

Search found 4141 results on 166 pages for 'router'.

Page 149/166 | < Previous Page | 145 146 147 148 149 150 151 152 153 154 155 156  | Next Page >

• Simple options for port forwarding to a different port?

  - by Nick

  I have three network printers at our local office, all of which listen on port 9100. Non of them offer the option of changing the listening port. We have a single public static IP address, and access to our main network is through a Linksys WRT-54G. We need to be able to print to these printers from outside the office. The problem is, with the 54G, I can only forward a port to the SAME port on a particular IP address. What I really need though is a way to forward to an ip address and a DIFFERENT port. I need to do this: In port Destination 9100 192.168.1.1 : 9100 9101 192.168.1.2 : 9100 9102 192.168.1.3 : 9100 So I'm looking for options. I could setup an old computer with two network cards and IPtables I suppose, but that seems like a lot of overhead for something relatively simple. Is there a way a virtual machine (read: one network card) could do the advanced port forwarding? Where I forward all traffic to it, and it forwards it on to the right printer? Or what about those mini Linux distros that replace the WRT-54G's firmware? Do any of those support what I need "out of the box"? I have a spare WRT- could I make it an IP tables router? Recommendations for mini distros? Or is there an off-the-shelf product that does this (cheap/local preferred)? Any advice / options appreciated. Thanks!

  Read the article

• IPSec Tunnel to Amazon EC2 - Netkey, NAT, and routing problem

  - by Ernest Mueller

  Hey all, I'm working on getting an IPSec VPN working between Amazon EC2 and my on-premise. The goal is to be able to safely administer stuff, up/download data, etc. over that tunnel. I have gotten the tunnel up in openswan between a Fedora 12 instance with an elastic IP and a Cisco router that's also NATted. I think the ipsec part is OK, but I'm having trouble figuring out how to route traffic that way; there's no "ipsec0" virutal interface because on Amazon you have to use netkey and not KLIPS for the vpn. I hear iptables may be required and I'm an iptables noob. On the left (Amazon), I have a 10. network. Box 1 is privately 10.254.110.A, publically IP 184.73.168.B. Netkey tunnel is up. Box 2 is publically 130.164.26.C, privately 130.164.0.D And my .conf is: conn ni type= tunnel authby= secret left= 10.254.110.A leftid= 184.73.168.B leftnexthop= %defaultroute leftsubnet= 10.254.0.0/32 right= 130.164.26.C rightid= 130.164.0.D rightnexthop= %defaultroute rightsubnet= 130.164.0.0/18 keyexchange= ike pfs= no auto= start keyingtries= 3 disablearrivalcheck=no ikelifetime= 240m auth= esp compress= no keylife= 60m forceencaps= yes esp= 3des-md5 I added a route to box 1 (130.164.0.0/18 via 10.254.110.A dev eth0) but that doesn't do it for predictable reasons, when I traceroute the traffic's still going "around" and not through the vpn. Routing table: 10.254.110.0/23 dev eth0 proto kernel scope link src 10.254.110.A 130.164.0.0/18 via 10.254.110.178 dev eth0 src 10.254.110.A 169.254.0.0/16 dev eth0 scope link metric 1002 Anyone know how to do the routing with a netkey ipsec tunnel where both sides are NATted? Thanks...

  Read the article

• Cacti is ignoring hash marks in interface aliases

  - by Matt Simmons

  I'm attempting to set up Cacti to monitor a router's interfaces, and I'm having trouble getting the graph templates to show the information that I'd like. Our interface configuration looks like this: interface GigabitEthernet3/6 description WalljackNumber # Server info no ip address no shutdown switchport switchport access vlan 116 switchport mode access ip dhcp snooping trust spanning-tree portfast The "Server Info" string is really just the machine name, and a short relevant description, such as "PolarSprings vmnic2". The important part appears to be that it follows the hashmark. When I run snmpwalk, I get the proper output: IF-MIB::ifAlias.230 = STRING: WalljackNumber # Server info But in Cacti, when I go into the graph templates and set the title to this: |host_description| - Traffic - |query_ifName| (|query_ifAlias|) All that shows up in the graph is: switchname - Traffic - Gi3/6 (WalljackNumber #) Which strikes me as a little weird. What I suppose MAY be happening is that somewhere in the cacti stream, it's interpreting # as being a comment and stripping everything after, but I'm not sure. I was hoping someone could tell me that this was a known documented behavior, or that I could change it in a setting that I wasn't aware of. The alternative answer is to change the delimiter from # to something else, but I've got over a thousand lit switchports on an old college infrastructure, and I'm not sure what else might be relying on them.

  Read the article

• Enable FTP on OS X 10.8 Mountain Lion Server

  - by Oleg Trakhman

  There is a LAN comprising several mac machines (iMac, Mac Pro, macbook etc.), Airport Express router and Mac Mini Server running OS X Server 10.8 (Mountain Lion Server). I need to share a folder on Mac Mini Server by FTP. What did I try so far: Made special partition for FTP Access, call it "Reports" So shared folder would be "/Volumes/Reports" Gave access every user and group in system, and also enabled guest access. I checked posix acl, which is "rwxrwxrwx", I checked sharing settings in "Preferences.app" and "Server.app" Checked that users have access to FTP service Enabled FTP in Server.app I tried access to shared folder (by FTP): via Cyberduck via Finder via shell: ftp server.local And what I got: $ ftp [email protected] Trying 10.0.2.2... Connected to server.local. 220 10.0.2.2 FTP server (tnftpd 20100324+GSSAPI) ready. 331 User ftpuser accepted, provide password. Password: 530 User ftpuser may not use FTP. and $ ftp [email protected] Trying 10.0.2.2... Connected to server.local. 220 10.0.2.2 FTP server (tnftpd 20100324+GSSAPI) ready. 331 User admin accepted, provide password. Password: 530 User admin denied by SACL. ftp: Login failed ftp> (admin is administrator account , ftpuser is special user account made to access ftp) What I'm doing wrong? Getting really tired of this...

  Read the article

• Typical outbound port list for guest access?

  - by Steve

  I manage a weekly rental house that includes wireless Internet access. I've allowed all outbound ports on my router but my ISP has disabled my Internet access twice now because guests have downloaded (or served up) copyrighted content. So I'd like to institute some port filtering to discourage p2p sharing (see disclaimer below). But I don't want to inconvenience the 99.9% of folks who keep things above-board. My question is, what outbound ports are typically open for rental/hotel wireless Internet access, or where can I find such a list? TCP 80,443,25,110 at a minimum. Though my own email service uses 995 and 465 for SSL, some may use IMAP, I personally use SSH and FTP, so I'll open those. Roughly I figure I need to open access to privileged ports, and close 1024 & above. Is there a whitelist I should institute for commonly used high ports? And does it make sense to block UDP 1024 ? Disclaimer: I realize anyone replying to this message could circumvent the port filtering and share content to their heart's content. I do not need comprehensive p2p blocking, which requires more than a port whitelist. Anyone staying at the house shoulders the responsibility for their Internet use, per the rental contract. Also anyone savvy enough to circumvent the port filters would hopefully be savvy enough to use some sort of peer blocking, thereby preventing the ISP from taking down the service.

  Read the article

• How to route to a secondary interface on the same physical ethernet?

  - by sjose3612611

  INTERNET<->(wan)BRIDGED_DEVICE(lan)<->ETH_ROUTER<->LAN Problem: Need to access web server on BRIDGED_DEVICE's LAN from INTERNET via ROUTER (BRIDGED_DEVICE's web server cannot be accessed form INTERNET since it has no Public management IP). Cannot configure bridged device. It has a static IP on its LAN to which its web server binds. Attempt: Create a secondary/alias WAN Interface on ETH_ROUTER (e.g Primary: eth0.1 (for internet access) and Secondary: eth0.2 (for accessing web server on BRIDGED_DEVICE), (No VLANs). eth0.1 has a public IP; eth0.2 has a static private IP in the BRIDGED_DEVICE's subnet (e.g 10.0.X.Y). Iptables on ETH_ROUTER: Added a port forward (DNAT) from eth0.1 to eth0.2: iptables -t nat -I PREROUTING -i eth0.1 -p tcp --dport 80 -j DNAT --to-destination 10.0.X.Y iptables -t nat -I POSTROUTING -o eth0.2 -s 10.0.X.0/24 -j MASQUERADE Stateful firewall w/ overall drop policy on FORWARD chain, hence: iptables -I FORWARD -i eth0.1 -d 10.0.X.Y -p tcp --dport 80 -j ACCEPT Can ping from ETH_ROUTER to BRIDGED_DEVICE but unable to reach the web server from Internet. I see packet cont increasing for the DNAT rule but not sure where it disappears in the ETH_ROUTER after that. ETH_ROUTER is the only device that can be configured to achieve this. If familiar with this scenario, please suggest what I may be missing or doing wrong here or suggest techniques to debug?

  Read the article

• Remote desktop type software that the client need not install anything...

  - by allentown

  I am primarily a Macintosh user, and can usually walk a client though any troubles they may have because I have a Macintosh in front of me. If they are on a different OS, things are close enough, or I cam remember, that I can get by. When trying to help clients on Windows, I get stuck. I do not have access to windows, and even if I did, there are far too many versions of Outlook, all with their various esoteric settings and checkboxes, that I could never see exactly what they are seeing. I mostly need to just help them with email setup. Something like copilot.com may do the trick. What is the simplest remote control software out there, ideally, it would accomplish these: No software needed on remote end, or, a single .exe that they can toss when done. I need Mac based software on my end. I do have ARD, which support VNC Free :) If possible, it would be really nice Needs a port forwarding proxy run by the company. There is no way I can get the user to alter their router, or to even plug directly into their WAN for a short time. On the Mac, I just have them open iChat, and this is all built in, proxying through AIM, looking for the same for Windows and Mac.

  Read the article

• What is the quickest reliable way to backup a NAS drive to a USB drive?

  - by Tim Murphy

  How would you backup 600+ GB of data on a NAS (Network-Attached Storage) drive to a USB external drive? The NAS drive does not contain mission critical data nonetheless I wish to make weekly copies of it just in case. The NAS drive is almost exclusively used as an archive dump and is rarely updated. However the backup strategy used must have a simple restore procedure so I can confidently say the data now on the NAS drive is exactly how it was at the time of backup. I did try xcopy but seemed like it would take many-many hours and eventually crashed with insufficient memory. http://www.ctunion.com/node/114 suggests I would need to use xxcopy instead due to folder/file name lengths. My concern with xcopy/xxcopy is the length of time it takes. Hoping something else is faster. NAS drive is DLink DNS-313. 1TB drive installed. Connected to router via Ethernet cable. USB drive is Seagate 1TB. Can be connected to Windows Vista (preferred) or Windows 7 PCs. Both PCs are usually connected Wirelessly however ethernet cable can be used during backup to speed up the process.

  Read the article

• VPN - local and remote networks IP collision

  - by Guido García

  I have created a VPN connection in Windows using the New Network Connection wizard that comes with Windows. It works without problems in most places, but there is one concrete place where, despite the connection to the remote public IP works fine, it is not able to validate the login/password and establish the VPN connection. In this place, the network is 10.0.0.x (the same I use in other places where I am able to connect). The remote network is 192.168.x.x, so I suspect there is some kind of IP collision, because before connecting, a traceroute to i.e. 192.168.0.40 does not fail. 1 4 ms 1 ms 1 ms LINKSYS [10.0.0.1] 2 5 ms 1 ms 1 ms 172.26.27.1 3 4 ms 5 ms 3 ms 192.168.1.100 ... (more) I can't modify the local network further than the first router (10.0.0.1). That is the only different I've found so far. Any idea about how to solve it? Thank you.

  Read the article

• How can I write automated tests for iptables?

  - by Phil Frost

  I am configuring a Linux router with iptables. I want to write acceptance tests for the configuration that assert things like: traffic from some guy on the internet is not forwarded, and TCP to port 80 on the webserver in the DMZ from hosts on the corporate LAN is forwarded. An ancient FAQ alludes to a iptables -C option which allows one to ask something like, "given a packet from X, to Y, on port Z, would it be accepted or dropped?" Although the FAQ suggests it works like this, for iptables (but maybe not ipchains as it uses in the examples) the -C option seems to not simulate a test packet running through all the rules, but rather checks for the existence for an exactly matching rule. This has little value as a test. I want to assert that the rules have the desired effect, not just that they exist. I've considered creating yet more test VMs and a virtual network, then probing with tools like nmap for effects. However, I'm avoiding this solution due to the complexity of creating all those additional virtual machines, which is really quite a heavy way to generate some test traffic. It would also be nice to have an automated testing methodology which can also work on a real server in production. How else might I solve this problem? Is there some mechanism I might use to generate or simulate arbitrary traffic, then know if it was (or would be) dropped or accepted by iptables?

  Read the article

• How to subnet hosted VMs

  - by bwizzy

  I have a network of VMs each having a LAN IP address and a public IP address. They each have a 1:1 NAT map for public access via the public IP for HTTP, SSH etc. I'm trying to figure out a way to restrict the LAN IPs from talking to each other, but there are some cases where a group of LAN IPs will need to communicate. I'm using pfSense as a firewall / router on a 192.168.0.0/24 configuration. It seems like I could assign each VM it's own subnet and add a static route to the firewall for that VM to get back to the firewall for internet access / other fw rules. Is that right? I assigned 1 VM with: address 192.168.1.2 netmask 255.255.255.254 gateway 192.168.1.1 Then added a static route on the FW's LAN interface using 192.168.1.0/30 as the destination network and 192.168.1.1 as the gateway. Nothing appears to be working, anyone have any ideas? Please be aware I'm not that familiar with subnets. Thanks!

  Read the article

• How to access Windows Server 2008 R2 file shares from a different subnet

  - by Lloyd Cotten

  We have a couple of severs that used to be Windows Server 2003 that we recently upgraded to Windows Server 2008 R2. A couple of details to set the situation up: We wiped the OS and re-installed. These servers are on one subnet (172.16.x.x) and we are trying to access some file shares on them from another subnet (10.34.x.x). Firewall is disabled on these servers. Trying to access with UNC "\172.16.x.x\sharename" and net use \172.16.x.x However, we're having problems doing this. We are getting "The network path was not found". Here's some of the things we've tried so far and the result: Tried accessing the share from other (non-2008) servers on the same subnet... Success! Ping servers from different subnet... Success! Telnet connection into port 139 from different subnet... Success! Took a scan through Local Security Policies to see if something obvious needed to be enabled / disabled / configured... Fail I'm not sure where to look next. I know that the router between the two subnets is locked down pretty good, but this did work for our 2003 servers. Has anything changed in the way of ports used for UNC / file share access in 2008? Maybe I'm missing some security policy setting? Hoping somebody can take pity on a poor programming guy that can't figure out something really simple. :-) Thanks!

  Read the article

• Natting trafic from a tunnel to internet

  - by mezgani

  I'm trying to set up a GRE tunnel between a linux box and a router (LAN), and I'm having a few problems which seem to depend to my iptables configuration. Watching with tcpdump on linux box, I can see packets coming with flags GREv0, all i need right know is forwarding this data to internet, found here some trace : iptables -F iptables -X iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -t nat -F iptables -t nat -X iptables -t nat -P PREROUTING ACCEPT iptables -t nat -P POSTROUTING ACCEPT iptables -t nat -P OUTPUT ACCEPT iptables -t mangle -F iptables -t mangle -X iptables -t mangle -P PREROUTING ACCEPT iptables -t mangle -P OUTPUT ACCEPT iptables -A INPUT -p 47 -j ACCEPT iptables -A FORWARD -i ppp0 -o cloud -j ACCEPT iptables -A FORWARD -i cloud -o ppp0 -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE echo "1" /proc/sys/net/ipv4/ip_forward cloud Link encap:UNSPEC HWaddr C4-CE-7A-2E-F2-BF-DD-C0-00-00-00-00-00-00-00-00 inet adr:10.3.3.3 P-t-P:10.3.3.3 Masque:255.255.255.255 UP POINTOPOINT RUNNING NOARP MTU:1476 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:124 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 RX bytes:0 (0.0 B) TX bytes:10416 (10.1 KiB) Table de routage IP du noyau Destination Passerelle Genmask Indic MSS Fenêtre irtt Iface 196.206.120.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.3.3.0 0.0.0.0 255.255.255.0 U 0 0 0 cloud 0.0.0.0 196.206.120.1 0.0.0.0 UG 0 0 0 ppp0 root@aldebaran:~# ip route 196.206.120.1 dev ppp0 proto kernel scope link src 196.206.122.46 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.18 10.3.3.0/24 dev cloud scope link default via 196.206.120.1 dev ppp0

  Read the article

• Single computer on network cannot connect to internet.

  - by user34630

  Hi All, I hope you can help me out! :) I have 3 computers and one device (Xbox) on my home network; 2 running XP and one on Vista. The computer that can't connect to the internet (XP) is old and failing, and shows no warning before it completely runs out of battery. Thus today, I started it up forgetting that I had unplugged it the night before, and it just ran out of battery entirely whilst I was using it and died. I think that before this I had been browsing the internet, but I can't remember for certain. (i.e. The problem I am having may or may not have been caused by this 'hard' power off). Anyway, now when I start the computer up it takes 5-10 minutes after logging on to display the start bar and icons. Also, I cannot browse the internet. The computer seems to connect to the network OK (I have tried both wired and wireless), but I can't visit sites and can't ping web addresses. Pinging the router fails, as does pinging another of my computers on the network. I have never encountered something like this before, and whilst I am no noob I am also not a sysadmin, haha. :( Any help is greatly appreciated, thank you for your time. P.S. I have tried a system restore (newbie move?).

  Read the article

• Persistent routes for DD-WRT PPTP VPN client

  - by Tim Kemp

  My home network in the USA is behind a Buffalo router (G300NH) running their version of DD-WRT. I use the built-in PPTP VPN client to connect to a VPN provider in the UK. I route certain traffic over the VPN (so it has a UK source address, for various entirely legal reasons) which I achieved by following the instructions in the DD-WRT docs and my VPN provider's own instructions. I placed two commands like this in the firewall script: route add -net xxx.xxx.0.0 netmask 255.255.0.0 dev ppp0 route add -net yyy.yyy.0.0 netmask 255.255.0.0 dev ppp0 I didn't put any of the iptables rules in since it my setup doesn't seem to need them. It works like a charm. Traffic to the xxx subnets goes over the VPN, everything else goes out over my ISPs own pipes. The problem comes when the VPN drops, which it does occasionally. DD-WRT does a fine job of reconnecting it automatically, but the routes are trashed every time that happens. How do I automate the process of re-establishing my routes? I thought about static routes, but the IP address of the VPN connection is dynamically assigned (which is why I'm using dev ppp0). Many thanks, Tim

  Read the article

• Specific DNS sometimes resolves to wildcard, incorrectly

  - by Mojo

  I have an intermittent problem, and I'm not sure where to start trying to troubleshoot it. In our dev environment, we have two visible IP addresses on load balancers, one to the front-end, and one to a number of back-end service machines. The front-end is configured to take a wildcard DNS name to support generic "portals." dev.example.com A 10.1.1.1 *.dev.example.com CNAME dev.example.com The back-end servers are all specific names within the same space: core.dev.example.com A 10.1.1.2 cms.dev.example.com CNAME core.dev.example.com search.dev.example.com CNAME core.dev.example.com Here's the problem. Periodically a developer or a program trying to reach, say, cms.dev.example.com will get a result that points to the front-end, instead of the back-end load balancer: cms.dev.example.com is an alias to core.dev.example.com core.dev.example.com is an alias to dev.example.com (WRONG!) dev.example.com 10.1.1.1 The developers are all on Mac OS X machines, though I've seen the problem occur on an Ubuntu machine as well, using a local cloud host DNS resolver. Sometimes the developer is using a VPN, which directs the DNS to its own resolver, and sometimes he's on the local net using a DNS resolver assigned by the NAT router. Sometimes clearing the Mac OS X DNS cache, logging into the VPN, then logging out of the VPN, will make the problem go away. The origin authoritative server is on zerigo, and a dig directly to their name servers always seems to give the correct answer. The published DNS cache time for these records is 15 minutes, but the problem has been intermittent for about a week. Any troubleshooting suggestions?

  Read the article

• OpenVZ with brdiged interfaces and VLAN

  - by Deimosfr

  Hi, I've got a problem with OpenVZ with brdiged VLAN. Here is my configuration : +------+ +-------+ +-----------+ +---------+ br0 |VE101 | | | | OpenBSD |----->| Debian |------->| | | WAN |--->| Router | | OpenVZ | +------+ | | | Firewall |----->| br0 br1 | br1 +------+ +-------+ +-----------+ +---------+------->|VE102 | |br0 | | |VLAN br0.110 +------+ v +---------+ |VE103.110| +---------+ I can't make VLAN working on br0 (br0.110) and I would like to understand why. I don't have any switch so no problem with unmanageable switch. I've configured a VLAN interface on OpenBSD in /etc/hostname.vlan110 : inet 192.168.110.254 255.255.255.0 NONE vlan 110 vlandev sis1 And it seams working fine. I've also adapted my PF configuration to work with VLAN but I don't see any incoming traffic. On my Debian lenny, here is my interfaces configuration : # The loopback network interface auto lo iface lo inet loopback # br0 auto br0 iface br0 inet static address 192.168.100.1 netmask 255.255.255.0 gateway 192.168.100.254 network 192.168.100.0 broadcast 192.168.100.255 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off # VLAN 110 auto br0.110 iface br0.110 inet static address 192.168.110.1 netmask 255.255.255.0 network 192.168.110.0 gateway 192.168.110.254 broadcast 192.168.110.255 pre-up vconfig add br0 110 post-down vconfig rem br0.110 It looks like ok, but when I start my VE, here is the message : ... Configure veth devices: veth103.0 Adding interface veth103.0 to bridge br0.110 on CT0 for VE103 can't add veth103.0 to bridge br0.110: Operation not supported VE start in progress... So I've got one error here. I've followed this documentation http://wiki.openvz.org/VLAN but it doesn't work. I've certainly missed something but I don't know why. Someone could help me please ? Thanks

  Read the article

• Strange behaviour when creating/deleting subdomains

  - by Saif Bechan

  This can be a DNS cache issue from my local machine, but I am not sure. This is what happens. I have a domain that does not use wildcard subdomains, so they have to be created. Without creating the domain, and I point my browser to test.domain.com, I get a page server not found. Now when I create the subdomain, I keep getting the same problem. Now when I first create the domain, without ever visiting the page, I get the normal page, but now when I delete the subdomain, it never goes away. Can this be a DNS cache issue, I am working on a shared environment, maybe the router has a cache but I doubt that. Can this have something to do with my setup. I have tried to use the Google DNS hosting, but this gives me the same results. I have also tried some tools that clear my local DNS cache, they were some add-ons for FireFox. Anyone have any ideas what can be the problem. Are there any tests I can do to see if there is some kind of cache between me and the server.

  Read the article

• Network to network VPN Centos 5

  - by Atul Kulkarni

  I am trying to follow "http://www.centos.org/docs/5/html/Deployment_Guide-en-US/ch-vpn.html#s1-ipsec-net2net" I have come up with the following On local router machine: in my ifcfg-ipsec0: ONBOOT=yes IKE_METHOD=PSK DSTGW=10.5.27.1 SRCGW=10.6.159.1 DSTNET=10.5.27.0/25 SRCNET=10.6.159.0/24 DST=205.X.X.X TYPE=IPSEC I have /etc/sysconfig/network-scripts/keys-ipsec0 file in place. On Remote Machine in the cloud if have /etc/sysconfig/network-scripts/ifcfg-ipsec1: TYPE=IPSEC ONBOOT=yes IKE_METHOD=PSK SRCGW=10.5.27.1 DSTGW=10.6.159.1 SRCNET=10.5.27.124/25 DSTNET=10.6.159.0/24 DST=38.x.x.x with its respective /etc/sysconfig/network-scripts/key-ipsec1 file. The DST in both cases are NAT'd external IPs. Is that a problem? I have made changes for port forwarding as well. When I try to bring the interfaces up it gives me output "RTNETLINK answers: Invalid argument". I am confused now and don't know what more to do? Any place I can digup what parameters were wrong? I really appreciate any help I can get. Thanks and Regards, Atul.

  Read the article

• open source solution to a gateway for a network of a housing cooperative of 150 people

  - by SirDinosaur

  i just inherited a barely functioning network for a student housing cooperative of about 150 people. in it's current state, as i understand it from the previous person in charge of the network, we have working wireless access points and working ethernet cords going to working gigabit switches going to a barely functioning gateway (right now a simple home router) to one of three possible outbound connections. it is possible to connect to the network through the wireless or ethernet, but especially during peak hours, packets / connections are likely dropped or otherwise get no response. my intuition tells me to replace the gateway with something that can handle multiple outbound connections (WAN) and one inbound connection (LAN), while the rest of the network seems suitable for now. i'm somewhat knowledgable in Linux (been using Debian after first Arch Linux) and i want to use as much open source as possible, but i'm confused whether or not a simple server that i could easily understand will work for this situation. do i need specialized hardware to handle the switching more effectively? if so, what are my options? (i found this, thoughts?) or if a Debian server would work, anything else i should about the specs required for this type of server? also links to any useful information on using open source to maintain this type of network would be most appreciated. <3 P.S. crossposted http://redd.it/yybp2.

  Read the article

• Process does ICMP port scan on my OSX box and I am afraid my Mac got a virus

  - by Jamgold

  I noticed that my 10.6.6 box has some process sending out ICMP messages to "random" hosts, which concerns me a lot. when doing a tcpdump icmp I see a lot of the following 15:41:14.738328 IP macpro > bzq-109-66-184-49.red.bezeqint.net: ICMP macpro udp port websm unreachable, length 36 15:41:15.110381 IP macpro > 99-110-211-191.lightspeed.sntcca.sbcglobal.net: ICMP macpro udp port 54045 unreachable, length 36 15:41:23.458831 IP macpro > 188.122.242.115: ICMP macpro udp port websm unreachable, length 36 15:41:23.638731 IP macpro > 61.85-200-21.bkkb.no: ICMP macpro udp port websm unreachable, length 36 15:41:27.329981 IP macpro > c-98-234-88-192.hsd1.ca.comcast.net: ICMP macpro udp port 54045 unreachable, length 36 15:41:29.349586 IP macpro > c-98-234-88-192.hsd1.ca.comcast.net: ICMP macpro udp port 54045 unreachable, length 36 I got suspicious when my router notified me about a lot of ICMP messages that don't get a response [INFO] Mon Jan 10 16:31:47 2011 Blocked outgoing ICMP packet (ICMP type 3) from 192.168.1.189 to 212.25.57.90 Does anyone know how to trace which process (or worse kernel module) might be responsible for this? I rebooted and logged in with a virgin user account and tcpdump showed the same results. Any dtrace magic welcome.

  Read the article

• IIS SSL is taking all IPs although it is told not to

  - by Martin Sall

  I have a testing system where IIS Express on Windows 7 SSL website has to live together with Cerberus FTP server SSL website (Cerberus FTP has a built-in web server for HTTP uploads). I have set up Windows to use two IPs from my router 192.168.1.128 (for IIS SSL Web Site, using a self-generated SSL certificate for now) 192.168.1.129 (for Cerberus FTP built-in SSL Web Site) In IIS I have set web site binding to use only the IP 192.168.1.128. But still when I launch Cerberus, it says - cannot bind 192.168.1.129:443. I tested in Firefox - indeed, when I go to 192.168.1.129 (or even localhost), I do not get “Unable to connect“ page as expected, but “The connection was reset” instead. IIS is still occupying those IPs, although it is not serving the website on those IPs. When I stop the IIS website, Cerberus FTP Website launches without problems. But then I cannot launch IIS web site, it tells - "The process cannot access the file because it is being used by another process". Why is IIS SSL web site still occupying all IPs?

  Read the article

• need advice on data center move, communication with both facilities during transition

  - by Brian Roden

  We are beginning the process of moving to a new facility. Office and warehouse operations will both be moving, and we must get shipping operations up and running at the new location while continuing to ship from the old location. Our contract with some third-party warehouse tenants requires two business day turnaround (only weekends and holidays excluded), so we can't have major downtime during the move. We would like to keep our 172.16.60/61.xxx internal address space in use throughout the move. Is it possible to keep using this same internal range, and have our existing WatchGuard Firebox 520 and whatever router we get for the other location (preferably the same model) just treat both locations as one network, leaving our host IPs the same throughout the move? Renumbering the servers when they move isn't a big deal, but our wireless terminals for order picking in the warehouse have fixed IPs (and a fixed IP, non-DNS reference to the host they speak with) and would be a massive undertaking to reconfigure when the servers move (each device would have to be reconfigured at least 2 times -- some when we start using them in the new building and the host is still here, all of them in both locations when the host moves to the new building, and the rest when they finally make the move to the new building). We're trying to avoid that if possible.

  Read the article

• Nexus One WiFi connection problems.

  - by sunocky

  I have two new Nexus One for a research project. For the projects I need to keep a server running on the phone. But soon I found out that both the phones have inconsistent WiFi connection problems at my home. It can connect to my WiFi network, but will drop off in a random time. And in order to reconnect to my WiFi, I may need to reboot my router, or the phone will say "obtaining IP address" and then "Unsuccessful". I also own a G1 with firmware version 1.6, it has no such connection problems. Well, to my surprise, the two Nexus One works fine with connecting to the WiFi network at my work place, which is a WEP type WiFi connection. By the way, it is a WPA type connection at my home. Anyone knows what's the problems with the Nexus One? Any suggestions on what should I do if I want to keep the WiFi connection live all the time at my home? Thanks very much!

  Read the article

• Backup plan for linux webserver in small business?

  - by radman

  Hi, I am currently in the process of writing a backup plan for the webserver in use by my business. I am very new to this area and have a few ideas about how things should work but am unsure of what tools to use and what sort of restore process is appropriate. I'm looking for something relatively simplistic and it doesn't have to be 100% paranoid just enough to give me a reliable backup. Speed is not of the essence and there is not going to be a live fallback in place. The backup will be onto a single hdd that will be stored onsite (no option for offsite as yet). Backups will be taking place weekly. I am constrained by both time and money which is why I'm aiming for a good enough solution. Is taking an image of the webserver system drive periodically and using that as the backup appropriate? Should I be testing that the backups restore correctly every time that I perform one? This is a bit broad but what setup would you use if you were in my place, given the services I am running? Should I add additonal machines and split the services? Any advice is much appreciated! See below for server details Webserver Platform Linux Ubuntu server Running mail-server svn-server mediawiki wordpress apache-webserver Hardware single 500gb sata drive Architecture Single machine behind router (with firewall) accessible to the internet.

  Read the article

< Previous Page | 145 146 147 148 149 150 151 152 153 154 155 156  | Next Page >