Search Results

Search found 8185 results on 328 pages for 'capture card'.

Page 15/328 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

  • hpdv6 6080 two graphic card

    - by Taher
    My laptop has two graphic card one is ati radeon 6770m and other intel sandybridge. i install ati driver from repository but i can't select ati as my graphic card after installing ati ubuntu lose 3d mode how can i set graphic card? and switch between two graphic cards? or how can i set one of them? my laptop is hp dv6 6080 and i add blacklist radeon to /etc/modprobe.d/blacklist.conf and add below lines to /etc/rc.local file: modprobe radeon echo OFF /sys/kernel/debug/vgaswitcheroo/switch exit 0

    Read the article

  • Impossible quandrary involving UCK, graphics card, and Nvidia drivers

    - by InkBlend
    I have a computer that I want to install Ubuntu on. It is an older gaming computer with a Nvidia graphics card. When I attempt to boot any unmodified Linux distribution onto it, I get a "Boot error" message, which I assume is because the computer uses a discrete graphics card, which the Linux kernel does not have support for. Ordinarily, that would not be a problem, as I would just plug the monitor into the VGA port built in to the motherboard. However, this particular model of motherboard does not have an on-board graphics connector, so I am stuck with using the graphics card connection. That further would not be a problem; all I would have to do would be to use UCK to create a customized Ubuntu image that included the graphics drivers. Except for the fact that the Nvidia Linux drivers must be installed on a computer with a Nvidia graphics card present. So while using UCK, the driver installer fails with a message stating that there is no Nvidia graphics card present. How do I get Ubuntu on my desktop computer?

    Read the article

  • I cannot upgrade to 12.10 because of graphic-card, Radeon HD 3450

    - by minime
    I wonder what has happened. I have Ubuntu 12.04 and Ati Radeon HD 3450 and that has supported 3D, now suddenly it does not accept my graphic-card. I really would like to know what to do? Should I buy a new graphic card or is there a way to use my graphic-card on 12.10? And if so what is there a graphic-card I should buy? My Ati is functioning with 3D, on 12.04 I don't understand why it will not upgrade to 12.10.

    Read the article

  • Ubuntu 11.0 HDMI Video Card No 5.1 Audio

    - by ryandlf
    I am using Ubuntu and XMBC on my HTPC and have chosen the Radeon HD5570 Video card which has an HDMI output. In the sound preferences there is no surround sound option for the video card just stereo and although I can get sound through it in XBMC, my receiver does not state Dolby Digital on movies that are in fact Dolby so its definitely not giving me the true sound it should. Does this card not support surround sound through HDMI and I somehow missed it? If that is the case does anyone have suggestion that has been tested and works? Id like to know its going to work before investing in yet another video card.

    Read the article

  • CellC data card not recognized if I boot with it in

    - by Armien
    In 11.10 I find that I can connect to the internet via broadband connection successfully. The problem is that I cannot have the data card attached to the machine while the machine boots up. If I leave the data card in the machine during startup, the data card is not picked up and I then cannot connect to the internet. I must first boot up my machine, login, attach the data card into the usb port, wait so 30 seconds. The broadband connection name will then appear in the network dropdown at the top of the screen. An internet connect is now possible via broadband. Please let me know what must be done to fix this.

    Read the article

  • Change Data Capture Webinar

    I am going to be doing a webinar with our friends at Attunity on Change Data Capture.  Attunity have a good story around this technology and you can use it in your SSIS loads to great effect. Join Attunity and Konesans/SQLIS for a Webinar on 17 September Space is limited. Reserve your Webinar seat now at: https://www1.gotomeeting.com/register/693735512 Want increased efficiency and real-time speed when conducting ETL loads? Need lower implementation costs while minimizing system impact? Learn how change data capture (CDC) technologies can reduce ETL load times. Allan Mitchell, Principal Consultant at Konesans and SQLServer MVP specialising in ETL, will explain CDC concepts and benefits and how CDC can dramatically reduce ETL load times. Ian Archibald, Pre-Sales Director EMEA for Attunity, will present and demonstrate Attunity's award-winning Oracle-CDC for SSIS, a fully-integrated SSIS solution for designing, deploying and managing Oracle CDC processes. Title: Change Data Capture - Reducing ETL Load Times Date: Thursday, September 17, 2009 Time: 10:00 AM - 11:00 AM BST ABOUT THE SPEAKERS: Allan Mitchell is the joint owner of Konesans Ltd, a UK based consultancy specializing in SQL Server, and most importantly SQL Server Integration Services. Having been working with SQL Server from 6.5 onwards, he has extensive experience in many aspects of SQL Server, but now focuses on the BI suite of tools. He is a SQL Server MVP, a frequent poster on the MS SSIS/DTS newsgroups, and runs the sqldts.com and sqlis.com resource sites. Ian Archibald, Attunity Pre-Sales Director EMEA, has worked in Attunity’s UK Office for 17 years. An expert in Attunity solutions, Ian has extensive knowledge of Attunity’s products and data integration & CDC technologies. After registering you will receive a confirmation email containing information about joining the Webinar. System Requirements PC-based attendees Required: Windows® 2000, XP Home, XP Pro, 2003 Server, Vista Macintosh®-based attendees Required: Mac OS® X 10.4 (Tiger®) or newer

    Read the article

  • Change Data Capture Webinar

    I am going to be doing a webinar with our friends at Attunity on Change Data Capture.  Attunity have a good story around this technology and you can use it in your SSIS loads to great effect. Join Attunity and Konesans/SQLIS for a Webinar on 17 September Space is limited. Reserve your Webinar seat now at: https://www1.gotomeeting.com/register/693735512 Want increased efficiency and real-time speed when conducting ETL loads? Need lower implementation costs while minimizing system impact? Learn how change data capture (CDC) technologies can reduce ETL load times. Allan Mitchell, Principal Consultant at Konesans and SQLServer MVP specialising in ETL, will explain CDC concepts and benefits and how CDC can dramatically reduce ETL load times. Ian Archibald, Pre-Sales Director EMEA for Attunity, will present and demonstrate Attunity's award-winning Oracle-CDC for SSIS, a fully-integrated SSIS solution for designing, deploying and managing Oracle CDC processes. Title: Change Data Capture - Reducing ETL Load Times Date: Thursday, September 17, 2009 Time: 10:00 AM - 11:00 AM BST ABOUT THE SPEAKERS: Allan Mitchell is the joint owner of Konesans Ltd, a UK based consultancy specializing in SQL Server, and most importantly SQL Server Integration Services. Having been working with SQL Server from 6.5 onwards, he has extensive experience in many aspects of SQL Server, but now focuses on the BI suite of tools. He is a SQL Server MVP, a frequent poster on the MS SSIS/DTS newsgroups, and runs the sqldts.com and sqlis.com resource sites. Ian Archibald, Attunity Pre-Sales Director EMEA, has worked in Attunity’s UK Office for 17 years. An expert in Attunity solutions, Ian has extensive knowledge of Attunity’s products and data integration & CDC technologies. After registering you will receive a confirmation email containing information about joining the Webinar. System Requirements PC-based attendees Required: Windows® 2000, XP Home, XP Pro, 2003 Server, Vista Macintosh®-based attendees Required: Mac OS® X 10.4 (Tiger®) or newer

    Read the article

  • ASUS EAH5450 Graphics Card (ATI Radeon HD5450 - 1 GB DDR3) on Windows 2003? Anybody got it to work?

    - by JJarava
    Hi all! I've just bought an ASUS EAH5450 Graphics Card (ATI Radeon HD5450, 1 GB DDR3) for my main system, but I haven't been able to make it work under Windows 2003 (my OS in that system). When I plugged the card, I got a couple of "installing drivers" prompt for things such as "ATI High Definition Audio Device" that got themselves sorted out of the Internet, and then a "Standard VGA Graphics Adapter". The CD that came with the card installs something called "ATI Catalyst Install Manager" and .net 2.0, but no drivers. I've downloaded the latest (WinXP 32bits) drivers from ATI, and the experience is the same: I don't get any drivers installed. My Motherboard is an ASUS A8N-SLI with nVidia nForce 4 chipset (for an Athlon 64X2, somewhat old), but my previous card was an ATi Radeon X700, so it's been working with ATI cards before. On POST, during boot I see a "Display Card" Device (Vendor ID 1002-68F9-0300) and a "Multimedia Device" (1002-AA68-0403), and when viewing the properties of the "Standard VGA", they match the device ID. Any hints? I'd really hate having to get rid of the card, and I'm sure it's not that strange what I'm trying to do...

    Read the article

  • 3 monitors + a TV on a single card with Eyefinity?

    - by Paul Accisano
    Greetings all, Right now I have a fairly standard video card with 2 DVI ports, one powering my single monitor and another powering my HDTV (with a DVI-to-HDMI cable), which are in separate rooms. I never need to have my monitor and TV active at the same time. I'm looking into a possible computer upgrade. I'd like to know if the following situation is possible. I want three monitors on my desk powered by a single card, which I hear these new Eyefinity cards are capable of. But, I also want my TV hooked up. At any given time, I would want either my three monitors active or my TV active, never both at once. So it seems to me it might be possible to do this all a single 3-port card with a splitter of some kind. Is this possible? What hardware would I need? Thanks!

    Read the article

  • Does upgrading RAM causes increase in Graphic card's share?

    - by A.S.
    I have asked this question on Ask Ubuntu, and I was suggested to Upgrade RAM from most voted answers. But I got a point about my graphics card. Since, I can upgrade RAM and not graphics card, Does upgrading RAM also cause graphics memory to increase. To clear the point: My specs are given below: Laptop : Lenovo 3000 Y410. (bought in 2008 October) RAM: 1 GB (DDR2) External Graphics (Dedicated): N/A Internal Graphics (Shared): 256 MB Graphics Chipset: Intel GMA X3100 My Question is: If I increase my RAM to 3 GB, will it increase graphics cards share of the Memory. In other word, If graphics card shares 256 MB in 1GB RAM, will it share more, when I upgrade the RAM into 2GB or more ? Authentic resource link will be much appreciated I have recently known that, My chipset GMA X3100 can address 384 MB of RAM. So the question.

    Read the article

  • Trying to get a PC to boot off a bootable SD card that is inside an USB attached Android device.

    - by Cyril
    First, I'd like to make myself look less a madman than I may have appeared to be. I wanted to have a bootable USB stick with me at all times, but it's less convenient because it's an extra object and it's easier to lose, forget etc. Then I thought, I have an Android phone, and it has a micro SD in it; perfect. Not all PC's can boot off a card reader, but the phone itself is a card reader when attached as a disk drive. Or at least so I thought. Turns out that my netbook BIOS (tested on Asus eeePC) refuses to see it as an external harddrive; it only recognizes it as a generic USB device and doesn't offer an option to boot from it. The device has a name "Android phone" or smth, so it seems to me that it doesn't work as a "pure" card reader, and instead still manifests itself as a phone. Can it be somehow overridden?

    Read the article

  • Motherboard warning lights when plugging in a display port cord to graphics card?

    - by rllr
    Earlier today, my computer spontaneously shut itself off and refused to turn back on. I tested my PSU and it's operating fine. I unplugged everything and let it sit for a while and it started to make a high pitched coil whine/hiss. When I came back an hour later and plugged in only the power cord, it turned on without any issues. After some troubleshooting, I noticed my motherboard (Intel D975XBX2) has a red CPU led and VR led that come on whenever I plug my monitor into my graphics card via display port. DVI does not cause a similar issue. I was running three monitors off the card, so I need both DVI ports and the display port working. Is it likely my graphics card needs to be replaced, or should I be looking elsewhere to resolve this issue?

    Read the article

  • Is the cooling fan on a 2004 graphics card really necessary?

    - by Andrew
    I have an old GeForce 6600 card in my computer, circa 2004. Recently the fan has started playing up and making loud irritating noises. I've tried oiling it with no luck. This is the second fan I've put on the card, the stock one broke ages ago. Is a card this old really likely to need a cooling fan or can I remove it altogether? It has a decent heatsink on the chip but there's not a lot of airflow in that part of the box. Edit: I should add that I seem to remember most mid range graphics cards at the time I bought that didn't have fans (pretty sure they had heatsinks only), which is why I'm wondering.

    Read the article

  • How to tell, before buying, if a given graphics card will play Full HD video?

    - by Dominykas Mostauskis
    I am looking for the cheapest video card that would be capable of smooth playback of Full HD (1080p) video on a Full HD screen. An answer by @Mikhail on a related question briefly mentioned that: performance of video playback is largely dependent on the video accelerators present [in the card] Is this true? Could anyone expand on that? Are there any benchmarks or specifications that could be used to tell if a given (low-end) card can play Full HD video smoothly? Benchmarks I encountered are oriented towards computer games, and using them to evaluate video playback performance may be less-than-optimal, I imagine.

    Read the article

  • Using Excel VBA to capture standard toolbar use

    - by vwankerl
    I am looking for a way to capture a click on a standard toolbar tool in Excel with VBA. The primary need is to capture any Copy, Cut, and Paste request by the user. I can capture the hot keys for these functions, but I can't find a way to capture the same functions when the user clicks on the icon on the standard toolbar or when the user uses the menu to select the function.

    Read the article

  • Software to capture the packets in an MPEG Transport Stream

    - by Crippledsmurf
    I have a DVB-T capture card and would like to capture the packets from the MPEG stream it receives so i can analyse them just for a bit of fun and learning I've googled and found a lot of converters and software to capture the video from these streams but very little in the area of capturing raw data from a stream. What software exists that can capture and dump the MPEG stream from a tuner?

    Read the article

  • Windows 2008 server smart card security module problem

    - by chris13work
    Hi, I've got a smart card reader and a server application using it as a security module. If I run it under DOS prompt, everything is fine. The server is running and clients can connect to it. I tried to install the server as window service and start it. The server starts but always gives back authentication error because it cannot call the smart card to do encryption. Then I tried to start it with task scheduler and set the trigger factor as "on startup". The server starts also but still cannot access the smart card reader. Then I tried remote desktop to the machine and run the server application under DOS prompt. Same error is returned. The situation is that the smart card reader only works under active console desktop environment. In the server application, WINSCARD API is used to access the smart card reader. Any suggestion so that we can access the smart card reader in running services? OS: Windows Server 2008 Smart Card Driver: Windows USB smart card Reader Smart Card API: WINSCARD

    Read the article

  • Windows 2008 server smart card security module problem

    - by chris13work
    Hi, I've got a smart card reader and a server application using it as a security module. If I run it under DOS prompt, everything is fine. The server is running and clients can connect to it. I tried to install the server as window service and start it. The server starts but always gives back authentication error because it cannot call the smart card to do encryption. Then I tried to start it with task scheduler and set the trigger factor as "on startup". The server starts also but still cannot access the smart card reader. Then I tried remote desktop to the machine and run the server application under DOS prompt. Same error is returned. The situation is that the smart card reader only works under active console desktop environment. In the server application, WINSCARD API is used to access the smart card reader. Any suggestion so that we can access the smart card reader in running services? OS: Windows Server 2008 Smart Card Driver: Windows USB smart card Reader Smart Card API: WINSCARD

    Read the article

  • Configure TV Capture card to not use external audio jack for TV audio output

    - by Adam D.
    I had this working with MythTV on Ubuntu 9.1. Then a power surge killed the motherboard. After replacing the motherboard, ram and cpu, the card does not produce any audio except through the output jack on the back of the card. I do not want to use a cable to go from the back of the card to the audio in on the built in sound card of the new mother board. FYI, the old motherboard did not have an on-board sound card. There was a separate audio card installed. There's some configuration that has to be done to have it work the same way again. I just have no idea where to start. This is regarding wintv hauppauge mythtv linux ubuntu 9.10 audio

    Read the article

  • Driver issue for 7850 HD Diamond Windows 7

    - by Mr.Student
    I have an issue with windows 7 implementing the drivers ati provides for my 7850 HD Diamond video card. The video card is plugged in correctly to the PCIE 2.0 slots of my motherboard (p6t asus) with more then enough power. Fortunately the card works as I have my monitor plugged into the card itself and I can see just fine. However windows 7 does not replace the standard vga default microsoft driver with catalyst drivers that I've tried installing from online as well as the CD. Every time I install the drivers using Catalyst Install manager it always finishes with "Install complete(Warnings occured)". I then see the warnings it has which it instead reports that it successfully installed the SDK, Catalyst Install Manager, and HDMI/AUDIO packages. When I check my device manager after that, the display adapter still shows as standard vga and that its still using microsoft default display adapter. Now this current card is replacing an old card of mine which is the ATI 4890 HD which works beautifully. In fact for the old card to work, all I need to do is go to device manager and right click on standard vga - click update driver and windows 7 magically finds the correct driver to install and everything is good. Not so with the new card. I've even went into my regedits and uninstalled every bit of ati driver software before reinstalling my new card. Nothing's worked thus far. I've already exchanged my card out once and talked to customer support from my motherboard, microsoft, and ati all blaming the other. Please help me out!!

    Read the article

  • Video memory buswidth vs video memory Bandwidth

    - by Mixxiphoid
    My current video card (9600GT) is dying and I'm searching for a new video card. Between acquiring my current one and now, I got a lot more knowledge about hardware and I want to use that to pick my new card. So I decided to not just buy some popular card blindly, but to search for a card able to handle my hardware requirements. I searched the specs at the NVidia site for the GT640 and was confused by the memory section and some questions raised. My current card's memory bus width is 256bit and has 1GB of memory. I checked Google about the importance of bus width. And all the links basically said the same 'The higher the number the more potential simultaneously traffic can be transferred'. This was already clear to me, yet there are currently a lot of new cards which are considered better than my current one with a lower bus width. To go in more detail about my question I copied the memory info from the NVidia site: GT 640 GT640 GDDR5 Memory Specs: Memory Clock 1.8 Gbps 5.0 Gbps Standard Memory Config 2048 MB 1024 MB Memory Interface DDR3 GDDR5 Memory Interface Width 128-bit 64-bit Memory Bandwidth (GB/sec) 28.5 40.0 What puzzled me is that the Memory Bandwidth seems to me the most important part, yet the lower bus width has the higher 'performance'. Is this due to the fact the memory interface is GDDR5 and is therefore able to have a higher memory clock speed (5Gbps)? If I am to buy a new video card, should I check the bus width? Memory clock? Bandwith? Amount of memory? My current card ahs 1GB memory, so I was searching for a 2GB memory card, but now I'm not so sure any more whether that is really 'better'. My main question: To me it seems that memory performance is made up by the combination of bus width and frequency. Is this true? If yes, why are there so many sites telling me I need to get a card with a high bus width? If no, then what IS important when it goes about memory performance on a video card. NOTE: The memory bandwidth is (almost) never displayed on vendor sites. How can I determine which card is better without knowing the bandwith?

    Read the article

  • Failed pinging a LAN card of the server from the client using shared internet connection

    - by bobo
    The server (Windows XP Pro SP3) has two LAN cards (LAN card A and B) and is connected to the internet using ADSL. The ADSL connection is shared to LAN card B using Internet Connection Sharing. The client (Windows XP Pro SP3) has one LAN card, and is connected to LAN card B of the server so that it has access to the internet. The IP address on the LAN cards are defined as follows: Server: LAN card A: 192.168.0.3/24 (manually defined by me) LAN card B: 192.168.0.1/24 (manually defined by Internet Connection Sharing) Client: LAN card: 192.168.0.123/24 (assigned by DHCP) Default gateway: 192.168.0.1 From the server, I can ping 192.168.0.123 successfully. From the client, it can access the internet without any problem. I can also ping 192.168.0.1 successfully but for 192.168.0.3, it failed with the Request Timeout error message. Why did the ping fail, and what should be done to make the ping possible? (all firewalls have been turned off.)

    Read the article

  • Card game in python

    - by matt1024
    What is the best way to store the cards and suits in python so that I can hold a reference to these values in another variable? For example, if I have a list called hand (cards in players hand), how could I hold values that could refer to the names of suits and values of specific cards, and how would these names and values of suits and cards be stored?

    Read the article

  • Maximum Year in Expry Date of Credit Card

    - by Art
    Various online services have different values for maximum year of expiry, when it comes to Credit Cards. For instance: Basecamp: +15 years (2025) Amazon: +20 years (2030) Paypal: +19 years (2029) What is the reasonable maximum here? Are there any official guidelines?

    Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >