Search Results

Search found 26928 results on 1078 pages for 'disk image'.

Page 15/1078 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

  • How HP D2700 disk enclosure is monitored for alarms via SNMP

    - by VSAC
    We have HP D2700 disk enclosure and we would like to monitor D2700 (connected to HP Proliant DL360G8) for alarms.I have following questions regarding this. What are the options available for reporting D2700 hardware alarms (disk failure, power failure) via SNMP? We understand the D2700 to have an Ethernet interface for controller A and B and alarms are available via SNMP via this interface. Can anyone provide the actual alarms via this interface? (MIB and alarm list) As we have a number of D2700’s and would like to minimize the number of physical connections to the switch and associated IP addresses; Is there a mechanism to monitor the D2700 from the SCSI connected HPDL360 and raise SNMP alarms from the DL360 for hardware failures on the D2700? If so can anyone provide details and the actual alarms and MIB via this mechanism? Thanks!

    Read the article

  • disk-to-disk backup without costly backup redundancy?

    - by AaronLS
    A good backup strategy involves a combination of 1) disconnected backups/snapshots that will not be affected by bugs, viruses, and/or security breaches 2) geographically distributed backups to protect against local disasters 3) testing backups to ensure that they can be restored as needed Generally I take an onsite backup daily, and an offsite backup weekly, and do test restores periodically. In the rare circumstance that I need to restore files, I do some from the local backup. Should a catastrophic event destroy the servers and local backups, then the offsite weekly tape backup would be used to restore the files. I don't need multiple offsite backups with redundancy. I ALREADY HAVE REDUNDANCY THROUGH THE USE OF BOTH LOCAL AND REMOTE BACKUPS. I have recovery blocks and par files with the backups, so I already have protection against a small percentage of corrupt bits. I perform test restores to ensure the backups function properly. Should the remote backups experience a dataloss, I can replace them with one of the local backups. There are historical offsite backups as well, so if a dataloss was not noticed for a few weeks(such as a bug/security breach/virus), the data could be restored from an older backup. By doing this, the only scenario that poses a risk to complete data loss would be one where both the local, remote, and servers all experienced a data loss in the same time period. I'm willing to risk that happening since the odds of that trifecta negligibly small, and the data isn't THAT valuable to me. So I hope I have emphasized that I don't need redundancy in my offsite backups because I have covered all the bases. I know this exact technique is employed by numerous businesses. Of course there are some that take multiple offsite backups, because the data is so incredibly valuable that they don't even want to risk that trifecta disaster, but in the majority of cases the trifecta disaster is an accepted risk. I HAD TO COVER ALL THIS BECAUSE SOME PEOPLE DON'T READ!!! I think I have justified my backup strategy and the majority of businesses who use offsite tape backups do not have any additional redundancy beyond what is mentioned above(recovery blocks, par files, historical snapshots). Now I would like to eliminate the use of tapes for offsite backups, and instead use a backup service. Most however are extremely costly for $/gb/month storage. I don't mind paying for transfer bandwidth, but the cost of storage is way to high. All of them advertise that they maintain backups of the data, and I imagine they use RAID as well. Obviously if you were using them to host servers this would all be necessary, but for my scenario, I am simply replacing my offsite backups with such a service. So there is no need for RAID, and absolutely no value in another layer of backups of backups. My one and only question: "Are there online data-storage/backup services that do not use redundancy or offer backups(backups of my backups) as part of their packages, and thus are more reasonably priced?" NOT my question: "Is this a flawed strategy?" I don't care if you think this is a good strategy or not. I know it pretty standard. Very few people make an extra copy of their offsite backups. They already have local backups that they can use to replace the remote backups if something catastrophic happens at the remote site. Please limit your responses to the question posed. Sorry if I seem a little abrasive, but I had some trolls in my last post who didn't read my requirements nor my question, and were trying to go off answering a totally different question. I made it pretty clear, but didn't try to justify my strategy, because I didn't ask about whether my strategy was justifyable. So I apologize if this was lengthy, as it really didn't need to be, but since there are so many trolls here who try to sidetrack questions by responding without addressing the question at hand.

    Read the article

  • Munin "Disk usage" is too high?

    - by f-aminov
    I've recently installed munin on my VMware client server and saw that the Disk usage shows about 80-90%. Everything else (cpu load, ram, etc.) seems to be running fine. I have only two virtual hosts on my server with 1000 users/day in total, so I don't think that's too much. Here is the graph for the disk usage. Server info: Debian Lenny, CPU 510Mhz, RAM 512MB Is it bad? What could possibly cause this? Thank you for any suggestions.

    Read the article

  • Using DD for disk cloning

    - by roe
    There's been a number of questions regarding disk cloning tools (yes, I did search for it) :) and dd has been suggested at least once. I've already considered using dd myself, mainly because ease of use, and that it's readily available on pretty much all run of the mill bootable linux distributions. To my question, what is the best way to use dd for cloning a disk. I don't have much time to go around, and no test-hardware to play with, so I need to be prepared, and it's pretty much a one-shoot chance to get it done. I did a quick google search, and the first result was an apparent failed attempt. Is there anything I need to do after using dd, i.e. is there anything that CAN'T be read using dd? Thanks!

    Read the article

  • Ubuntu hard disk problem

    - by Henadzy
    Hello! I have got the error with a hard disk on Ubuntu 9.10. It slows down my system, applications have not been responding for a long time. But when I mount and use filesystem which placed on this hard disk at other computer it works properly. disk: SAMSUNG HD161HJ (SATA) syslog: Apr 25 00:28:25 vare6gin kernel: [ 885.773839] ata3.00: exception Emask 0x1 SAct 0x1e SErr 0x0 action 0x6 frozen Apr 25 00:28:25 vare6gin kernel: [ 885.773845] ata3.00: Ata error. fis:0x21 Apr 25 00:28:25 vare6gin kernel: [ 885.773861] ata3.00: cmd 60/08:08:3f:00:ad/00:00:10:00:00/40 tag 1 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773864] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773871] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773877] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773890] ata3.00: cmd 60/18:10:9f:6b:ed/00:00:0e:00:00/40 tag 2 ncq 12288 in Apr 25 00:28:25 vare6gin kernel: [ 885.773893] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773900] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773904] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773918] ata3.00: cmd 60/08:18:3f:5f:ed/00:00:0e:00:00/40 tag 3 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773921] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773927] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773932] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773946] ata3.00: cmd 60/08:20:67:c8:91/00:00:05:00:00/40 tag 4 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773948] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773955] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773960] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773970] ata3: hard resetting link Apr 25 00:28:25 vare6gin kernel: [ 885.773974] ata3: nv: skipping hardreset on occupied port Apr 25 00:28:25 vare6gin kernel: [ 886.240073] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 25 00:28:25 vare6gin kernel: [ 886.256277] ata3.00: configured for UDMA/133 Apr 25 00:28:25 vare6gin kernel: [ 886.256305] ata3: EH complete Apr 25 00:28:27 vare6gin kernel: [ 888.176088] ata3: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF Apr 25 00:28:27 vare6gin kernel: [ 888.176099] ata3: SWNCQ:qc_active 0xF defer_bits 0x0 last_issue_tag 0x3 Apr 25 00:28:27 vare6gin kernel: [ 888.176102] dhfis 0xF dmafis 0x1 sdbfis 0x0 Apr 25 00:28:27 vare6gin kernel: [ 888.176109] ata3: ATA_REG 0x51 ERR_REG 0x40 Apr 25 00:28:27 vare6gin kernel: [ 888.176113] ata3: tag : dhfis dmafis sdbfis sacitve Apr 25 00:28:27 vare6gin kernel: [ 888.176120] ata3: tag 0x0: 1 1 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176126] ata3: tag 0x1: 1 0 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176131] ata3: tag 0x2: 1 0 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176136] ata3: tag 0x3: 1 0 0 1

    Read the article

  • Ubuntu hard disk problem

    - by Henadzy
    Hello! I have got the error with a hard disk on Ubuntu 9.10. It slows down my system, applications have not been responding for a long time. But when I mount and use filesystem which placed on this hard disk at other computer it works properly. disk: SAMSUNG HD161HJ (SATA) syslog: Apr 25 00:28:25 vare6gin kernel: [ 885.773839] ata3.00: exception Emask 0x1 SAct 0x1e SErr 0x0 action 0x6 frozen Apr 25 00:28:25 vare6gin kernel: [ 885.773845] ata3.00: Ata error. fis:0x21 Apr 25 00:28:25 vare6gin kernel: [ 885.773861] ata3.00: cmd 60/08:08:3f:00:ad/00:00:10:00:00/40 tag 1 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773864] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773871] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773877] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773890] ata3.00: cmd 60/18:10:9f:6b:ed/00:00:0e:00:00/40 tag 2 ncq 12288 in Apr 25 00:28:25 vare6gin kernel: [ 885.773893] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773900] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773904] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773918] ata3.00: cmd 60/08:18:3f:5f:ed/00:00:0e:00:00/40 tag 3 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773921] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773927] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773932] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773946] ata3.00: cmd 60/08:20:67:c8:91/00:00:05:00:00/40 tag 4 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773948] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773955] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773960] ata3.00: error: { UNC } Apr 25 00:28:25 vare6gin kernel: [ 885.773970] ata3: hard resetting link Apr 25 00:28:25 vare6gin kernel: [ 885.773974] ata3: nv: skipping hardreset on occupied port Apr 25 00:28:25 vare6gin kernel: [ 886.240073] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 25 00:28:25 vare6gin kernel: [ 886.256277] ata3.00: configured for UDMA/133 Apr 25 00:28:25 vare6gin kernel: [ 886.256305] ata3: EH complete Apr 25 00:28:27 vare6gin kernel: [ 888.176088] ata3: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF Apr 25 00:28:27 vare6gin kernel: [ 888.176099] ata3: SWNCQ:qc_active 0xF defer_bits 0x0 last_issue_tag 0x3 Apr 25 00:28:27 vare6gin kernel: [ 888.176102] dhfis 0xF dmafis 0x1 sdbfis 0x0 Apr 25 00:28:27 vare6gin kernel: [ 888.176109] ata3: ATA_REG 0x51 ERR_REG 0x40 Apr 25 00:28:27 vare6gin kernel: [ 888.176113] ata3: tag : dhfis dmafis sdbfis sacitve Apr 25 00:28:27 vare6gin kernel: [ 888.176120] ata3: tag 0x0: 1 1 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176126] ata3: tag 0x1: 1 0 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176131] ata3: tag 0x2: 1 0 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176136] ata3: tag 0x3: 1 0 0 1

    Read the article

  • No space left on device with encrypted disk that takes all space

    - by Yosef
    I use Ubuntu 11.04. There's no space left on device. I have encrypted the disk that takes up space (maybe it's good to disable it, but I don't know how). In shell, I get this message: No space left on device I run df -I: Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda1 3055616 602499 2453117 20% / none 210161 890 209271 1% /dev none 214789 8 214781 1% /dev/shm none 214789 53 214736 1% /var/run none 214789 3 214786 1% /var/lock /home/myuser/.Private 3055616 602499 2453117 20% /home/myuser df -I Edit: When I run only df: Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda1 48060296 45618928 0 100% / none 1538340 684 1537656 1% /dev none 1547596 808 1546788 1% /dev/shm none 1547596 104 1547492 1% /var/run none 1547596 0 1547596 0% /var/lock /home/myuser/.Private 48060296 45618928 0 100% /home/myuser Edit: I thinking about few solution but I don't know which better and how exactly to do them: to enlarge partition size (I cant install gparted - no more disk space) remove encryption of partition - I really not need that

    Read the article

  • Running a Check-Disk (Is it dangerous)

    - by vaccano
    I have a lap top that a friend of mine would like me to fix. It is giving a blue screen on boot up. When I looked up the error message it indicates that I should run a check disk. Is this dangerous? Should I try to off load stuff from the hard drive first? I ask because I had a hard drive of my own that when I ran check disk it wiped a bunch of "bad sectors" and I lost most of the info on it (but it had been going bad). Opinions?

    Read the article

  • Add Mirror for volumes other than the last one in Windows 7 (disk "not up-to-date")

    - by rakslice
    I'm using Windows 7 x64 Ultimate. I have an existing 4TB disk with 3 NTFS volumes, a new 3TB blank disk, and I'm trying to mirror the volumes onto the new disk. My Windows install is on an SSD which is Disk 0. The 4TB disk with volumes is Disk 1, and the new blank disk is Disk 2. I can add a mirror successfully for the last volume, but when I try to add a mirror for the first volume I immediately get errors (see below). Is there something I special I need to do to add a mirror for a volume other than the last one? More info: I opened Disk Management, right-clicked on the first volume on the existing disk, went to Add Mirror, and selected the new disk. The first time I did this I was prompted to convert the new disk to a Dynamic Disk, which I approved. Subsequently I got a message: The operation failed to complete because the Disk Management console view is not up-to-date. Refresh the view by using the refresh task. If the problem persists close the Disk Management console, then restart Disk Management or restart the computer. I've refreshed disk management, restarted the computer, and converted the new disk to basic and back to dynamic, but I still get that error message. Looking around for suggestions of a workaround, I saw a suggestion to use the diskpart command line tool. Running diskpart from the Start Menu as Administrator, I did select volume 2 (the first volume I want to mirror) and then add disk 2 (the new disk), and received a somewhat similar error: Virtual Disk Service error: The disk's extent information is corrupted. DiskPart has referenced an object which is not up-to-date. Refresh the object by using the RESCAN command. If the problem persists exit DiskPart, then restart DiskPart or restart the computer. A rescan appears to be successful: DISKPART> select disk 2 Disk 2 is now the selected disk. DISKPART> rescan Please wait while DiskPart scans your configuration... DiskPart has finished scanning your configuration. but attempting to add the mirror again resulted in the same error. The only similar report I found online was this: http://www.sevenforums.com/hardware-devices/335780-unable-mirror-all-but-last-partition-drive.html Based on that I attempted to mirror the last volume on the disk to the new disk using diskpart, and that started successfully -- it is currently resynchronizing. More Background: In the course of dealing with a failing 3TB hard drive, I bought a replacement 4TB drive and installed it, then copied the partitions from the failing drive to it using Minitool Partition Wizard Home, and then removed the failing drive and was up and running again normally. Now I've received a warranty replacement for the failing drive, and installed it, and now I'm attempting to mirror my partitions to it.

    Read the article

  • HP MediaSmart server system disk full

    - by Blanthor
    I have a HP MediaSmart Server (EX 490) with Windows Home Server out of the box. It comes with a single 1.0 TB drive partioned 20 GB for the System disk. The system disk keeps filling up. I haven't installed anything but McAfee. Without getting into the philosophical discussions of why they would partition it thus, what is the likely culprit of this debacle? My D: Partition has plenty of space. I can get into the server only through Remote Desktop.

    Read the article

  • Windows Disk I/O Analysis

    - by Jonathon
    It appears that we are having a problem with the disk i/o speed on our Windows 2003 Enterprise Edition server (64-bit). As we were initializing a database that created two 1G tablespaces on 3 different machines, it became obvious that the two smaller machines (each 32-bit Windows 2003 Standard Edition with less RAM) killed the larger machine when creating the files. The larger machine took 10x as long to create the tablespaces than did the other machines. Now, I am left wondering how that could be. What programs or scripts would you guys recommend for tracking down the I/O problem? I think the issue may be with the controller card (all boxes are hardware RAID 10, but have different controller cards), but I would like to check the actual disk I/O speed as well, so I have some hard numbers to work with. Any help would be appreciated.

    Read the article

  • windows seven disk check error

    - by crazybmanp
    i have gotten the error in the microsoft KB article 975778 (http://support.microsoft.com/kb/975778/en-us) i was able to get onto my computer luckily, but when i went on to get the hotfix that is stated in the article, it gave me this error when i ran it: "the update is not applicable to your computer." is there any way of getting the disk check error to stop, or to get this fix to work. i will answer any questions on hardware if you post the questions in the comments. answers to questions this is the a full version that i got from ASUS as an upgrade disk from windows vista (hopefully more specific than you were asking)

    Read the article

  • Need help solving "Disk Error Press any key to restart" after blue screen in XP.

    - by Dennis
    I have had a couple of BSOD's lately and after the last one I got the disk error message. The disk shows up during the BIOS portion of the boot. It is in a Dell Precision 690 so the F12 key gives me a boot menu. I can boot from the utility partition, and if I specifically select the hard drive from the boot menu it will boot fine. Any ideas why if I just try to do an unattended boot, it give the error listed in the title?

    Read the article

  • Can I make my drives visible and change their partition type without losing my data?

    - by user165408
    I have made a lot of mistakes and now I cannot see my hard disk nor I can start my operating system on my laptop. All my passwords and important files on my hdd without any backup. I followed this course of action Changed my hard disk partitions to dynamic just for getting 5th partition. (1st mistake) Decreased partitions to 4 again. Backed up operating system from 4th to 3rd partition with Norton Ghost. Booted from a live CD for Windows XP. Formatted 4th partition and moved my all important data from 1st and 2nd partitions to the 4th partition. Deleted 1st and 2nd partitions and got 1 partition from half of empty space. So I have just 3 partitions and empty space between 1st and 2nd partitions. Tried to install Windows 8 to the first partition but it did not allow because it is dynamic. Also it did not allow to install to other partitions. Tried to install Windows XP to the 1st partition but it said if I continue I cannot use other drivers. Therefore I escaped from installing it. Booted from the Windows XP live CD then increased 1st partiton to less than 400mb of empty space. Therefore I thought it will be adjacent but it was shown as 2 partitions. In my computer I see just 3 drivers. Using Norton Ghost I recovered my OS to the 1st partition. (2nd mistake it was on 4th partition originally) Booted from a Windows XP live CD I tried to install bcdedit to the Windows XP live CD but it did not work. Then I tried to install EaseUS Partition Master Home Edition. It was installed with errors then I start it and it showed me an error like there is no hard disk. I looked to my PC and my drivers were not there. Booted from the Norton Ghost CD and it did not show me my drivers either, but before I was able to see them. I checked numbers of partition shown by the Norton Ghost utility and they are still have same numbers so I have to see my drivers but I cannot see them now. My hard disk is shown as extarnal dynamic now so I cannot see any drive in my PC in the live Windows XP. There are two options; first one is import extarnal disk and second one is convert disk to basic. Will they delete my data? I fear booting from CDs like Windows XP live CD, Norton Ghost CD, and the operating system CD/DVD, because they may overwrite a few MB their data to my data. These recover tools are already exist in Windows XP live CD by The Ultimate Boot CD for Windows. Can any of them help me? CompuAppa SwissKnife V3 DBXtract Disk Investigator Fab's AutoBackup 2.0 FileRecovery Floppy Repair Free Undelete Handy Recovery Recovery Manager Restorastion Restorastion Help File by UBCD4Win UnChk Unstoppable Copier Finally How can I make it so that my drives are visible again without losing my data? How can I convert my dynamic partitions to basic without losing my data?

    Read the article

  • Hyper-V Virtual Disk Creation Taking Forver

    - by mnemosyn
    After some struggle, I finally managed to set up Hyper-V 2008 R2 on our server. So I connected to it using the Hyper-V Manager from a Windows 7 client and used the "New Virtual Machine Wizard". I set up a 350GB virtual hard disk. So I hit the "finish" button and the Hyper-V manager has been working for 24hours now, showing merely a dialog "Creating Disk". A console on the Hyper-V still reports 99.9% free space on the HD, but the machines HD LED flashes from time to time (making a rather idle impression, it's not flashing frenetically). Does this usually take this long? Is there a way to find out whether it's still working or just idling? Should I repeat the process? Guides on the net tell me to be patient, but 1d seems a bit extreme!?

    Read the article

  • Compressed disk image on Linux

    - by Aaron Digulla
    I just got my new computer with a much bigger harddisk. I think I copied all important files over but just to be sure, I'd like to keep a disk image of my old disk. To save space, I'd like to compress it but I didn't find an option to mount a compressed image. My goals: Result must be easy to access No need to decompress the whole thing before I can access anything Files should be quick to locate - no TAR/CPIO archive Necessary space should be less than just copying the files over So ideally, I'm looking for a read-only, compressed file system which I can create in a file and which grows automatically.

    Read the article

  • Check the disk for problems on Debian Lenny

    - by Equ
    Hi guys! I just bought a VPS hosting with Debian Lenny (I'm new to all this world). I've managed to install and setup everthing I need pretty well. My testing website works fast as expected most of the time, but sometimes it is really slow (response time is about 5-10 seconds). I checked everything and seems that there are may be some disk issues. How can I check the disk for problems/performance? What else could possible cause such a behaviour? Thank you!

    Read the article

  • Transfer disk contents *without* cloning tools

    - by Chris Cummins
    Is it possible to "clone" a disk which contains programs by performing a copy of all the disk contents (preserving file attributes) from source to destination disk, and unplugging the source disk and changing the drive letter of the destination disk to match that of the source? Context I have a two disk Windows 8 system with a system drive and a data drive. Recently, the data drive developed a number of bad sectors leading to IO errors. I have been sent a replacement drive so I simply need to clone the contents of this data drive onto the replacement. The drive contents include documents & media, user folders (My Documents and related), and some programs (games etc). Problem The problem is that the bad sectors on the source disk causes most disk cloning tools to fail with read errors. Attempted approaches include: Disk clone from live boot environment with Acronis True Image. Fails due to read errors. Disk clone from live boot environment with Clonezilla. Fails due to read errors. Disk clone using Roadkil's Unstoppable Copier. Fails due to hardware timeouts in the HDD (application hangs indefinitely). A straightforward copy from source to destination disk using FreeFileSync (preserving file attributes and metadata). This succeeds. So at the moment I have a replacement disk which contains all of the data from the original disk. Now all I need to is somehow get Windows to replace all references to the old disk to the new one. Is this possible by simply swapping the assigned drive letters? Any help would be greatly appreciated, thanks!

    Read the article

  • Disk fragmentation when dealing with many small files

    - by Zorlack
    On a daily basis we generate about 3.4 Million small jpeg files. We also delete about 3.4 Million 90 day old images. To date, we've dealt with this content by storing the images in a hierarchical manner. The heriarchy is something like this: /Year/Month/Day/Source/ This heirarchy allows us to effectively delete days worth of content across all sources. The files are stored on a Windows 2003 server connected to a 14 disk SATA RAID6. We've started having significant performance issues when writing-to and reading-from the disks. This may be due to the performance of the hardware, but I suspect that disk fragmentation bay be a culprit at well. Some people have recommended storing the data in a database, but I've been hesitant to do this. An other thought was to use some sort of container file, like a VHD or something. Does anyone have any advice for mitigating this kind of fragmentation?

    Read the article

  • Facebook Game Rejected: "Your app icon must not overlap with content in your cover image"

    - by peterwilli
    Sorry if this isnt the right stackexchange site to ask this, it was really hard to determine. My FB game just recently got rejected for 2 reasons. The first I fixed nicely and is irrelevant but the second I just can't see to figure out what they mean and I was hoping someone else got the same issue and did know what they meant. These are the errors: You can ignore the error under "Banners" The web preview of my game looks like this now: All I know is that the rejection has something to do with the cover image, not the icons or the screenshots. Please let me know what to do to get approved. Thanks a lot!

    Read the article

  • Drawing shapes dynamically on an image through web browser

    - by Tom Beech
    We have a scenario where we create floor plans of locations when we visit. The floor plan is finally shown on the web. It's come to the point now where we want to show floor plans but have a key with various items on them, when an item on the key is clicked, the image should highlight all the areas of the floorplan that have that specific item. I guess we're looking for some sort of open standard javascript lib to deal with SVG (has to work pre IE9 so pure SVG wont cut it) and the floor plans have to be able to be created through a .net application to be deployed on the web. I'd rather stay away from flash if at all possible to be honest. Below are a few conceptual images of what we're trying to achieve.

    Read the article

  • Why is the root partition on my disk full?

    - by Agmenor
    I installed Ubuntu 12.04 by doing a fresh install where there was previously Ubuntu 11.10. My computer warns me now that my disk is nearly full. After having run apt-get purge, run apt-get autoremove and emptied the Trash can, I still have this problem as shown by this screenshot of Gparted: The disk /dev/sda7 is indeed full. I ran the Disk Usage Analyzer (Baobab) and I am still not sure of what is happening: One of my hypothesis is that when installing Ubuntu 12.04, I didn't configure my disks well and the disk /dev/sda6 is not mounted well as /home. Is this the reason indeed? What should I do to verify this and then to get the things fixed? Here are a few additional details to answer the questions I received (thank you everybody): My home directory is not encrypted. The Backup utility (Déjà Dup) is not set for automatic backups. (I do it myself and manually.) After I mount /dev/sda6, the command df -h gives Filesystem Size Used Avail Use% Mounted on /dev/sda7 244G 221G 12G 96% / udev 3,9G 4,0K 3,9G 1% /dev tmpfs 1,6G 904K 1,6G 1% /run none 5,0M 0 5,0M 0% /run/lock none 3,9G 164K 3,9G 1% /run/shm /dev/sda6 653G 189G 433G 31% /media/8ec2fa69-039b-4c52-ab1b-034d785132a1 (sorry but formatting this into code does not work, for an unknown reason) Thanks to izx's post, I realized /dev/sda6 was not even mounted before. It contains all the documents I used to have when I was running Ubuntu 11.10.

    Read the article

  • Absorbtion 2d image effect

    - by Ed.
    I want to create a specyfic 2d image effect. It consists in modifying a sprite so it looks like it is being zoomed to a point or "absorbed" by that point. I'm not really sure what is the technical name of this effect so I cannot explain it correctly. Here you can see a video of what I'm talking about, it is the effect when the character absorbs the three glyphs. http://www.youtube.com/watch?v=PIo-GddsMcU&t=4m45s What is the name of this effect? How can I implement it with XNA for 2D textures/sprites?

    Read the article

  • Image Recognition (Shape recognition)

    - by mqpasta
    I want to recognize the shapes in the picture by template matching.Is the "ExhaustiveTemplateMatching" is the right option given in Aforge.Net for this purpose.Had anyone tried this class and find it working correctly.How accurate and right choice this class is for achieving my purpose.Suggest any other methods or Alogrithms as well for recognizing shapes by matching template.For example Identifying ComboBox in a picture.

    Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >