Search Results

Search found 33162 results on 1327 pages for 'static ip address'.

Page 15/1327 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

• Inbound SIP calls through Cisco 881 NAT hang up after a few seconds

  - by MasterRoot24

  I've recently moved to a Cisco 881 router for my WAN link. I was previously using a Cisco Linksys WAG320N as my modem/router/WiFi AP/NAT firewall. The WAG320N is now running in bridged mode, so it's simply acting as a modem with one of it's LAN ports connected to FE4 WAN on my Cisco 881. The Cisco 881 get's a DHCP provided IP from my ISP. My LAN is part of default Vlan 1 (192.168.1.0/24). General internet connectivity is working great, I've managed to setup static NAT rules for my HTTP/HTTPS/SMTP/etc. services which are running on my LAN. I don't know whether it's worth mentioning that I've opted to use NVI NAT (ip nat enable as opposed to the traditional ip nat outside/ip nat inside) setup. My reason for this is that NVI allows NAT loopback from my LAN to the WAN IP and back in to the necessary server on the LAN. I run an Asterisk 1.8 PBX on my LAN, which connects to a SIP provider on the internet. Both inbound and outbound calls through the old setup (WAG320N providing routing/NAT) worked fine. However, since moving to the Cisco 881, inbound calls drop after around 10 seconds, whereas outbound calls work fine. The following message is logged on my Asterisk PBX: [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3641 retrans_pkt: Retransmission timeout reached on transmission [email protected] for seqno 1 (Critical Response) -- See https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions Packet timed out after 6528ms with no response [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3670 retrans_pkt: Hanging up call [email protected] - no reply to our critical packet (see https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions). (I know that this is quite a common issue - I've spend the best part of 2 days solid on this, trawling Google.) I've done as I am told and checked https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions. Referring to the section "Other SIP requests" in the page linked above, I believe that the hangup to be caused by the ACK from my SIP provider not being passed back through NAT to Asterisk on my PBX. I tried to ascertain this by dumping the packets on my WAN interface on the 881. I managed to obtain a PCAP dump of packets in/out of my WAN interface. Here's an example of an ACK being reveived by the router from my provider: 689 21.219999 193.x.x.x 188.x.x.x SIP 502 Request: ACK sip:[email protected] | However a SIP trace on the Asterisk server show's that there are no ACK's received in response to the 200 OK from my PBX: http://pastebin.com/wwHpLPPz In the past, I have been strongly advised to disable any sort of SIP ALGs on routers and/or firewalls and the many posts regarding this issue on the internet seem to support this. However, I believe on Cisco IOS, the config command to disable SIP ALG is no ip nat service sip udp port 5060 however, this doesn't appear to help the situation. To confirm that config setting is set: Router1#show running-config | include sip no ip nat service sip udp port 5060 Another interesting twist: for a short period of time, I tried another provider. Luckily, my trial account with them is still available, so I reverted my Asterisk config back to the revision before I integrated with my current provider. I then dialled in to the DDI associated with the trial trunk and the call didn't get hung up and I didn't get the error above! To me, this points at the provider, however I know, like all providers do, will say "There's no issues with our SIP proxies - it's your firewall." I'm tempted to agree with this, as this issue was not apparent with the old WAG320N router when it was doing the NAT'ing. I'm sure you'll want to see my running-config too: ! ! Last configuration change at 15:55:07 UTC Sun Dec 9 2012 by xxx version 15.2 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone no service password-encryption service sequence-numbers ! hostname Router1 ! boot-start-marker boot-end-marker ! ! security authentication failure rate 10 log security passwords min-length 6 logging buffered 4096 logging console critical enable secret 4 xxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 quit no ip source-route no ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! no ip bootp server ip domain name dmz.merlin.local ip domain list dmz.merlin.local ip domain list merlin.local ip name-server x.x.x.x ip inspect audit-trail ip inspect udp idle-time 1800 ip inspect dns-timeout 7 ip inspect tcp idle-time 14400 ip inspect name autosec_inspect ftp timeout 3600 ip inspect name autosec_inspect http timeout 3600 ip inspect name autosec_inspect rcmd timeout 3600 ip inspect name autosec_inspect realaudio timeout 3600 ip inspect name autosec_inspect smtp timeout 3600 ip inspect name autosec_inspect tftp timeout 30 ip inspect name autosec_inspect udp timeout 15 ip inspect name autosec_inspect tcp timeout 3600 ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn ! ! username xxx privilege 15 secret 4 xxx username xxx secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp no ip redirects no ip unreachables no ip proxy-arp ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.2 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! no ip nat service sip udp port 5060 ip nat source list 1 interface FastEthernet4 overload ip nat source static tcp x.x.x.x 80 interface FastEthernet4 80 ip nat source static tcp x.x.x.x 443 interface FastEthernet4 443 ip nat source static tcp x.x.x.x 25 interface FastEthernet4 25 ip nat source static tcp x.x.x.x 587 interface FastEthernet4 587 ip nat source static tcp x.x.x.x 143 interface FastEthernet4 143 ip nat source static tcp x.x.x.x 993 interface FastEthernet4 993 ip nat source static tcp x.x.x.x 1723 interface FastEthernet4 1723 ! ! logging trap debugging logging facility local2 access-list 1 permit 192.168.1.0 0.0.0.255 access-list 1 permit 192.168.0.0 0.0.0.255 no cdp run ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 login authentication local_auth length 0 transport output all line aux 0 exec-timeout 15 0 login authentication local_auth transport output all line vty 0 1 access-class 1 in logging synchronous login authentication local_auth length 0 transport preferred none transport input telnet transport output all line vty 2 4 access-class 1 in login authentication local_auth length 0 transport input ssh transport output all ! ! end ...and, if it's of any use, here's my Asterisk SIP config: [general] context=default ; Default context for calls allowoverlap=no ; Disable overlap dialing support. (Default is yes) udpbindaddr=0.0.0.0 ; IP address to bind UDP listen socket to (0.0.0.0 binds to all) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) tcpenable=no ; Enable server for incoming TCP connections (default is no) tcpbindaddr=0.0.0.0 ; IP address for TCP server to bind to (0.0.0.0 binds to all interfaces) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) srvlookup=yes ; Enable DNS SRV lookups on outbound calls ; Note: Asterisk only uses the first host ; in SRV records ; Disabling DNS SRV lookups disables the ; ability to place SIP calls based on domain ; names to some other SIP users on the Internet ; Specifying a port in a SIP peer definition or ; when dialing outbound calls will supress SRV ; lookups for that peer or call. directmedia=no ; Don't allow direct RTP media between extensions (doesn't work through NAT) externhost=<MY DYNDNS HOSTNAME> ; Our external hostname to resolve to IP and be used in NAT'ed packets localnet=192.168.1.0/24 ; Define our local network so we know which packets need NAT'ing qualify=yes ; Qualify peers by default dtmfmode=rfc2833 ; Set the default DTMF mode disallow=all ; Disallow all codecs by default allow=ulaw ; Allow G.711 u-law allow=alaw ; Allow G.711 a-law ; ---------------------- ; SIP Trunk Registration ; ---------------------- ; Orbtalk register => <MY SIP PROVIDER USER NAME>:[email protected]/<MY DDI> ; Main Orbtalk number ; ---------- ; Trunks ; ---------- [orbtalk] ; Main Orbtalk trunk type=peer insecure=invite host=sipgw3.orbtalk.co.uk nat=yes username=<MY SIP PROVIDER USER NAME> defaultuser=<MY SIP PROVIDER USER NAME> fromuser=<MY SIP PROVIDER USER NAME> secret=xxx context=inbound I really don't know where to go with this. If anyone can help me find out why these calls are being dropped off, I'd be grateful if you could chime in! Please let me know if any further info is required.

  Read the article

• PHP - static DB class vs DB singleton object

  - by Marco Demaio

  I don't want to create a discussion about singleton better than static or better than global, etc. I read dozens of questions about it on SO, but I couldn't come up with an answer to this SPECIFIC question, so I hope someone could now illuminate me buy answering this question with one (or more) real simple EXAMPLES, and not theoretical discussions. In my app I have the typical DB class needed to perform tasks on DB without having to write everywhere in code mysql_connect/mysql_select_db/mysql... (moreover in future I might decide to use another type of DB engine in place of mySQL so obviously I need a class of abstration). I could write the class either as a static class: class DB { private static $connection = FALSE; //connection to be opened //DB connection values private static $server = NULL; private static $usr = NULL; private static $psw = NULL; private static $name = NULL; public static function init($db_server, $db_usr, $db_psw, $db_name) { //simply stores connections values, withour opening connection } public static function query($query_string) { //performs query over alerady opened connection, if not open, it opens connection 1st } ... } or as a Singletonm class: class DBSingleton { private $inst = NULL; private $connection = FALSE; //connection to be opened //DB connection values private $server = NULL; private $usr = NULL; private $psw = NULL; private $name = NULL; public static function getInstance($db_server, $db_usr, $db_psw, $db_name) { //simply stores connections values, withour opening connection if($inst === NULL) $this->inst = new DBSingleton(); return $this->inst; } private __construct()... public function query($query_string) { //performs query over already opened connection, if connection is not open, it opens connection 1st } ... } Then after in my app if I wanto to query the DB i could do //Performing query using static DB object DB:init(HOST, USR, PSW, DB_NAME); DB::query("SELECT..."); //Performing query using DB singleton $temp = DBSingleton::getInstance(HOST, USR, PSW, DB_NAME); $temp->query("SELECT..."); My simple brain sees Singleton has got the only advantage to avoid declaring as 'static' each method of the class. I'm sure some of you could give me an EXAMPLE of real advantage of singleton in this specific case. Thanks in advance.

  Read the article

• java unload static fields

  - by Alina Danila

  I have a java class that uses complex static fields which need special operations as close() so that they are safely cleaned by GC. For the initialization of static fields I use the static block. But I don't now how to unload the static field safely, so that I can call the close() method before the field is cleaned up by GC. Is there any way to unload a static field, similar to the static initialization block?

  Read the article

• Getting my ip address

  - by AntonioCS

  Hey! I have a computer on a small network, so my ip is 192.168.2.100. I am trying to get my real ip. I download the no-ip client but that just seems like a lot of trouble for such a simple thing. I created this php script that got http://www.ip-adress.com/ page and retrieved the ip it gave me. Is there a simpler way? Either using C, WSH or something. Or if there is an easier way in php please tell me. When I get the ip I'll uploaded it to my ftp site so that I can see the ip from work.

  Read the article

• Accessing non-static combbox property in the static method.

  - by Harikrishna

  I have one combobox on the window form and I have one method which is declared with static like private static DataTable ParseTable(HtmlNode table) Now I want to use combobox in that method for using combobox property but I can not access any property of combobox or combobox itself.If I made the combobox declaration as static then it can be accessed in that static method.But any alternative way to access combbox property in that static method because I don't want to make combobox declaration as static.

  Read the article

• Linux / C++: Get the IP Address of local computer

  - by BlaM

  This Question is almost the same as the previously asked Get the IP Address of local computer-Question. However I need to find the IP address(es) of a Linux Machine. So: How do I - programmatically in C++ - detect the IP addresses of the linux server my application is running on. The servers will have at least two IP addresses and I need a specific one (the one in a given network (the public one)). I'm sure there is a simple function to do that - but where? [EDIT] To make things a bit clearer: The server will obviously have the "localhost": 127.0.0.1 The server will have an internal (management) IP address: 172.16.x.x The server will have an external (public) IP address: 80.190.x.x I need to find the external IP address to bind my application to it. Obviously I can also bind to INADDR_ANY (and actually that's what I do at the moment). I would prefer to detect the public address, though.

  Read the article

• PLESK direct www.domain.com to another server with a unique IP

  - by Cudos

  Hello. I got a customer where I host mail and www address on my server with PLESK 9.2 I want to direct the www address to another IP address like this: Original: www.domain.com -> IP: 1.2.3.4 mail.domain.com -> IP: 1.2.3.4 webmail.domain.com -> IP: 1.2.3.4 New: www.domain.com -> IP: 22.22.22.22 mail.domain.com -> IP: 1.2.3.4 webmail.domain.com -> IP: 1.2.3.4

  Read the article

• Control Reference Static Method Performance

  - by dotnetguts

  I have just asked which one is better? Static Vs Non-Static? http://stackoverflow.com/questions/3016717/static-vs-non-static-method-performance-c I would like to take this discussion one step ahead. Consider If i pass reference of Panel control as parameter to Public static method, will static method still rules in performance?

  Read the article

• Are variables in the main methods static.

  - by vaibhav

  Its a well known fact that a static method can work only on static members. public static void Main() { Test t1 = new Test(); } Here the Main method is static, but I haven't declared t1 as static. Is it implicitly static?

  Read the article

• Static member object of a class in the same class

  - by Luv

  Suppose we have a class as class Egg { static Egg e; int i; Egg(int ii):i(ii) {} Egg(const Egg &); //Prevents copy-constructor to be called public: static Egg* instance() {return &e} }; Egg Egg::e(47); This code guarantees that we cannot create any object, but could use only the static object. But how could we declare static object of the same class in the class. And also one thing more since e is a static object, and static objects can call only static member functions, so how could the constructor been called here for static object e, also its constructors are private.

  Read the article

• Static IP on FEDORA12 from Virtualbox

  - by Diego Castro

  I'm trying to get my FEDORA12 to have an STATIC IP - inside virtualbox - inside Ubuntu Let me rephrase that. I have an Ubuntu 9.04 system with vitualbox and a FEDORA12 vm there and I would like to put the fedora with an STATIC IP (amahi needs it), but I'm getting stuck... I'm using NAT (if that's any help) I tryid a few tutorials, but no go. I'm kind of new to the *nix world but I'm old school on M$ Edit: Screenshots UBUNTU 9.04 (host that has the vm) hxxp://pic.imagefap.com/images/full/43/154/1548751086.jpg FEDORA hxxp://pic.imagefap.com/images/full/43/205/2050216515.jpg hxxp://pic.imagefap.com/images/full/43/118/1182276176.jpg (sory cant post pics... not enough rep)

  Read the article

• Address (url) forwarding with Vyatta

  - by Trikks

  Hi Got this kind of noob question i suppose. I got this very basic network setup and need help to set up some address forwarding. As seen in my illustration below all traffic enters via the eth0 interface (85.123.32.23). The external dns is setup to direct all hosts to this ip as well. Now, how on earth do I filter the incoming requests to each box? The Ip's are static! Se the network layout here: http://vyatta.org/files/u11160/setup.png I do not wish to solve this by assigning tons of ports etc. In my wishful thinking something like this would be nice :) set service nat rule 10 type destination set service nat rule 10 inbound-interface eth0 set service nat rule 10 destination address ftp.myhost.com set service nat rule 10 inside-address address 192.168.100.20 This way ALL traffic to the address ftp.myhost.com (at eth0) should be routed to the internal ip, 192.168.100.20. Right, is there anyone who could point in some direction? Maybe it's wrong to use nat? Please help me! :)

  Read the article

• Address (url) forwarding with Vyatta

  - by Trikks

  Got this kind of noob question i suppose. I got this very basic network setup and need help to set up some address forwarding. As seen in my illustration below all traffic enters via the eth0 interface (85.123.32.23). The external dns is setup to direct all hosts to this ip as well. Now, how on earth do I filter the incoming requests to each box? The Ip's are static! My network layout: I do not wish to solve this by assigning tons of ports etc. In my wishful thinking something like this would be nice :) set service nat rule 10 type destination set service nat rule 10 inbound-interface eth0 set service nat rule 10 destination address ftp.myhost.com set service nat rule 10 inside-address address 192.168.100.20 This way ALL traffic to the address ftp.myhost.com (at eth0) should be routed to the internal ip, 192.168.100.20. Right, is there anyone who could point in some direction? Maybe it's wrong to use nat? Please help me! :)

  Read the article

• Changing order of Thunderbird email address autocomplete?

  - by Brooks Moses

  I recently did a system wipe and installed Thunderbird 3.0, and imported all of my email setup from a previous Thunderbird 2.0 installation. Almost everything is working fine, but I'm having a problem with the autocomplete in email addresses when writing messages. The relevant behavior is this: In the old 2.0 installation, the autocomplete appeared to know which email addresses I used most frequently, and so when I typed "m" in the address line, it would pick as the default selection the "m"-person who I frequently write email to. (It's possible this is an illusion and it simply picked people in the order I added them to my address book.) Thus, I have become used to typing "m"-"enter" in the address field, and getting this person. In the current 3.0 installation, however, the autocomplete order has changed. It's not the same as it was, and it's not alphabetical. The result is that I'm spending extra time looking at the email address bar, and more annoyingly, half the time the old muscle-memory kicks in and I find myself with an email that's addressed to a couple of customers rather than to my boss and coworker. Thus, two questions: How does Thunderbird determine this autocomplete order, among a set of addresses all of which are in the same address book? How can I change this ordering to be what I want? (I have tried Google-searching, and found a number of incomplete answers, nearly all of which were for version 1.0 or thereabouts, and reference settings dialog boxes that no longer exist.)

  Read the article

• cloning mac address of physical server converted into vmware server

  - by user24981

  We've recently converted a physical Windows Server 2003 into vmware using P2V. However, one of the pieces of software on the 2003 machine are still looking for the old server's network MAC address in order to run. I've read several articles where it's discussed that you can modify the last part of the generated address and set it to static, but I need to clone the whole mac address to mimic the one in the old server. We're running CentOS and VMware server 2.0 as the host system. I was told that maybe adding in a second network card in the host and setting the virtual system's nic to that card instead of "bridged" would allow me to edit the vmx file and clone the whole MAC address. I can't use the old network card from the physical server because it's ISA and our new bus is PCI Any ideas? Thanks, Mike

  Read the article

• is it possible to get IP address of a wifi that you are not connected to

  - by coltonon

  Just like the question states. Is it somehow possible to get the IP address of a network that you don't have access to? For example, if you click the little wifi button on your task bar, and highlight your cursor over one of the options, you get some info. But your external IP address is actually the address of the router, isn't it? Which would mean you would have to connect to the wifi, and then the router to get an IP address, correct? I realy just want a simple answer: No or Yes and here's how

  Read the article

• network endpoint accessible via hostname only, not address?

  - by Dustin Getz

  someone told me that this piece of network hardware (NAS) has a security setting such that it can only be accessed by hostname, not by IP address. I don't understand, as I thought DNS resolved the hostname to an address on the connecting client's side, then at protocol level always used the raw address, so how can this 'security' measure be possible?

  Read the article

• Setting a Static IP Running FreeBSD8 in VirtualBox hosted on Windows 7

  - by gvkv

  I'm using VirtualBox on Windows 7 (host) to run a FreeBSD (guest) based web server. I`ve assigned a static ip of 192.168.80. 1 to the (virtualized) NIC which is run in bridged mode. The problem is that when I ping an external server (such as google.com) I get a No route to host error: dimetro# ping google.com PING google.com (66.249.90.104): 56 data bytes ping: sendto: No route to host ... I can ping the BSD server from both another virtualized machine and my host machine and from the server, I can ping everything on the network. The router ip is 192.168.1.1/16. ADDENDUM: I have the following lines in /etc/rc.conf on the BSD VM to configure networking: defaultrouter="192.168.1.1" ifconfig_em0="inet 192.168.80.1 netmask 255.255.0.0"

  Read the article

• Relaying requests between third party server and Heroku for static IP

  - by Gady

  I have a rails application hosted on Heroku that I need to integrate with 3rd party payments provider. The payment provider requires that my application will have a static IP for incoming and outgoing HTTPS requests. I want to deploy a proxy on a Linode VPS so it can relay the information as a proxy. Relaying the request to the service provider seems easy, I just use their IP. Can I relay requests coming from the service provider to the heroku application? Can I realy the request using a URL (https://myapp.herokuapp.com) ? What is the recommended proxy server to use?

  Read the article

• Can Linux report IP conflicts?

  - by James

  If a Red Hat or other Linux host has a conflict with an IP address, is there a way to have it display a warning message on the console or in a log, like Windows and MacOS do? i.e. my computer has an IP address configured (or received from a DHCP server) but finds another device on the network using the assigned address. Will it log the conflict?

  Read the article

• Force an LXC container to use its own IP address

  - by emma sculateur

  Sorry if this question has already been asked. I could not find it, I have this setup : +---------------------------------------------------------------------------------------------+ |HOST | | | | +-------------------------------------------------+ | | | UBUNTU-VM | | | | | | | | +-------------------+ | | | | |UBUNTU-LXC | | +------------------+ | | | | 10.0.0.3/24 | 10.0.0.1/24 | |OTHER VM | | | | | eth0-----lxcbr0----------eth0-----------br0----------eth0 | | | | | | 192.168.100.2/24| 192.168.100.1/24 |192.168.100.3/24 | | | | +-------------------+ | +------------------+ | | +-------------------------------------------------+ | +---------------------------------------------------------------------------------------------+ When I ping 192.168.100.3 from my UBUNTU-LXC, the source IP address is automatically changed to 192.168.100.2 by UBUNTU-VM. It's like having a NAT, whereas I really want my UBUNTU-LXC to talk with it own IP address. Is there any way to do this ? Edit : these info may be relevant : I am using KVM +libvirt to set up my VMs Here is how I create my interface in UBUNTU-VM : <interface type='bridge'> <mac address='52:54:00:cb:aa:74'/> <source bridge='br0'/> <model type='e1000'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x09' function='0x0'/> </interface>

  Read the article

• Ubuntu second static IP, ifconfig, /etc/network/interfaces

  - by Schmoove

  I would like to add a second static IP to my local Ubuntu 11.10 desktop machine and have it automatically available after rebooting. So far I am successfully using ifconfig to to temporarily set up an alias for my primary network interface: # ifconfig eth1:0 192.168.178.3 up # ifconfig eth1 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:feef:a3d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:61929 errors:0 dropped:0 overruns:0 frame:0 TX packets:64034 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:45330863 (45.3 MB) TX bytes:28175192 (28.1 MB) Interrupt:42 Base address:0x4000 eth1:0 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.3 Bcast:192.168.178.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:42 Base address:0x4000 However, when I add the following to /etc/network/interfaces, the alias is not up and running as expected after a reboot: # vi /etc/network/interfaces auto eth1:0 iface eth1:0 inet static address 192.168.178.3 netmask 255.255.255.0 I would like to know what to configure to get this to work. As a side note, I am running gnome shell.

  Read the article

• Address book software that knows people share addresses

  - by Benjol

  I'm a bit frustrated with Outlook and Google contacts, as neither understand that people share addresses, or that one address can represent several people. So you either have crappy custom fields like "Bill's mobile", "Jane's mobile", or you have a Bill and a Jane contact, and you have to keep the address updated between the two. Are the any decent, and simple, address book applications out there which have this kind of intelligence? Note: this is for home use, I don't need to do professional 'contact management'.

  Read the article

• Cisco Pix how to add an additional block of static ip addresses for nat?

  - by Scott Szretter

  I have a pix 501 with 5 static ip addresses. My isp just gave me 5 more. I am trying to figure out how to add the new block and then how to nat/open at least one of them to an inside machine. So far, I named a new interface "intf2", ip range is 71.11.11.58 - 62 (gateway should 71.11.11.57) imgsvr is the machine I want to nat to one of the (71.11.11.59) new ip addresses. mail (.123) is an example of a machine that is mapped to the current existing 5 ip block (96.11.11.121 gate / 96.11.11.122-127) and working fine. Building configuration... : Saved : PIX Version 6.3(4) interface ethernet0 auto interface ethernet0 vlan1 logical interface ethernet1 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 nameif vlan1 intf2 security1 enable password xxxxxxxxx encrypted passwd xxxxxxxxx encrypted hostname xxxxxxxPIX domain-name xxxxxxxxxxx no fixup protocol dns fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 no fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 names ...snip... name 192.168.10.13 mail name 192.168.10.29 imgsvr object-group network vpn1 network-object mail 255.255.255.255 access-list outside_access_in permit tcp any host 96.11.11.124 eq www access-list outside_access_in permit tcp any host 96.11.11.124 eq https access-list outside_access_in permit tcp any host 96.11.11.124 eq 3389 access-list outside_access_in permit tcp any host 96.11.11.123 eq https access-list outside_access_in permit tcp any host 96.11.11.123 eq www access-list outside_access_in permit tcp any host 96.11.11.125 eq smtp access-list outside_access_in permit tcp any host 96.11.11.125 eq https access-list outside_access_in permit tcp any host 96.11.11.125 eq 10443 access-list outside_access_in permit tcp any host 96.11.11.126 eq smtp access-list outside_access_in permit tcp any host 96.11.11.126 eq https access-list outside_access_in permit tcp any host 96.11.11.126 eq 10443 access-list outside_access_in deny ip any any access-list inside_nat0_outbound permit ip 192.168.0.0 255.255.0.0 IPPool2 255.255.255.0 access-list inside_nat0_outbound permit ip 172.17.0.0 255.255.0.0 IPPool2 255.255.255.0 access-list inside_nat0_outbound permit ip 172.16.0.0 255.255.0.0 IPPool2 255.255.255.0 ...snip... access-list inside_access_in deny tcp any any eq smtp access-list inside_access_in permit ip any any pager lines 24 logging on logging buffered notifications mtu outside 1500 mtu inside 1500 ip address outside 96.11.11.122 255.255.255.248 ip address inside 192.168.10.15 255.255.255.0 ip address intf2 71.11.11.58 255.255.255.248 ip audit info action alarm ip audit attack action alarm pdm location exchange 255.255.255.255 inside pdm location mail 255.255.255.255 inside pdm location IPPool2 255.255.255.0 outside pdm location 96.11.11.122 255.255.255.255 inside pdm location 192.168.10.1 255.255.255.255 inside pdm location 192.168.10.6 255.255.255.255 inside pdm location mail-gate1 255.255.255.255 inside pdm location mail-gate2 255.255.255.255 inside pdm location imgsvr 255.255.255.255 inside pdm location 71.11.11.59 255.255.255.255 intf2 pdm logging informational 100 pdm history enable arp timeout 14400 global (outside) 1 interface global (outside) 2 96.11.11.123 global (intf2) 3 interface global (intf2) 4 71.11.11.59 nat (inside) 0 access-list inside_nat0_outbound nat (inside) 2 mail 255.255.255.255 0 0 nat (inside) 1 0.0.0.0 0.0.0.0 0 0 static (inside,outside) tcp 96.11.11.123 smtp mail smtp netmask 255.255.255.255 0 0 static (inside,outside) tcp 96.11.11.123 https mail https netmask 255.255.255.255 0 0 static (inside,outside) tcp 96.11.11.123 www mail www netmask 255.255.255.255 0 0 static (inside,outside) 96.11.11.124 ts netmask 255.255.255.255 0 0 static (inside,outside) 96.11.11.126 mail-gate2 netmask 255.255.255.255 0 0 static (inside,outside) 96.11.11.125 mail-gate1 netmask 255.255.255.255 0 0 access-group outside_access_in in interface outside access-group inside_access_in in interface inside route outside 0.0.0.0 0.0.0.0 96.11.11.121 1 route intf2 0.0.0.0 0.0.0.0 71.11.11.57 2 timeout xlate 0:05:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00 timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute floodguard enable ...snip... : end [OK] Thanks!

  Read the article

• Cisco PIX 515 doesn't seem to be passing traffic through according to static route

  - by Liquidkristal

  Ok, so I am having a spot of bother with a Cisco PIX515, I have posted the current running config below, now I am no cisco expert by any means although I can do basic stuff with them, now I am having trouble with traffic sent from the outside to address: 10.75.32.25 it just doesn't appear to be going anywhere. Now this firewall is deep inside a private network, with an upstream firewall that we don't manage. I have spoken to the people that look after that firewall and they say they they have traffic routing to 10.75.32.21 and 10.75.32.25 and thats it (although there is a website that runs from the server 172.16.102.5 which (if my understanding is correct) gets traffic via 10.75.32.23. Any ideas would be greatly appreciated as to me it should all just work, but its not (obviously if the config is all correct then there could be a problem with the web server that we are trying to access on 10.75.32.25, although the users say that they can get to it internally (172.16.102.8) which is even more confusing) PIX Version 6.3(3) interface ethernet0 auto interface ethernet1 auto interface ethernet2 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 nameif ethernet2 academic security50 fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 names name 195.157.180.168 outsideNET name 195.157.180.170 globalNAT name 195.157.180.174 gateway name 195.157.180.173 Mail-Global name 172.30.31.240 Mail-Local name 10.75.32.20 outsideIF name 82.219.210.17 frogman1 name 212.69.230.79 frogman2 name 78.105.118.9 frogman3 name 172.16.0.0 acadNET name 172.16.100.254 acadIF access-list acl_outside permit icmp any any echo-reply access-list acl_outside permit icmp any any unreachable access-list acl_outside permit icmp any any time-exceeded access-list acl_outside permit tcp any host 10.75.32.22 eq smtp access-list acl_outside permit tcp any host 10.75.32.22 eq 8383 access-list acl_outside permit tcp any host 10.75.32.22 eq 8385 access-list acl_outside permit tcp any host 10.75.32.22 eq 8484 access-list acl_outside permit tcp any host 10.75.32.22 eq 8485 access-list acl_outside permit ip any host 10.75.32.30 access-list acl_outside permit tcp any host 10.75.32.25 eq https access-list acl_outside permit tcp any host 10.75.32.25 eq www access-list acl_outside permit tcp any host 10.75.32.23 eq www access-list acl_outside permit tcp any host 10.75.32.23 eq https access-list acl_outside permit tcp host frogman1 host 10.75.32.23 eq ssh access-list acl_outside permit tcp host frogman2 host 10.75.32.23 eq ssh access-list acl_outside permit tcp host frogman3 host 10.75.32.23 eq ssh access-list acl_outside permit tcp any host 10.75.32.23 eq 2001 access-list acl_outside permit tcp host frogman1 host 10.75.32.24 eq 8441 access-list acl_outside permit tcp host frogman2 host 10.75.32.24 eq 8441 access-list acl_outside permit tcp host frogman3 host 10.75.32.24 eq 8441 access-list acl_outside permit tcp host frogman1 host 10.75.32.24 eq 8442 access-list acl_outside permit tcp host frogman2 host 10.75.32.24 eq 8442 access-list acl_outside permit tcp host frogman3 host 10.75.32.24 eq 8442 access-list acl_outside permit tcp host frogman1 host 10.75.32.24 eq 8443 access-list acl_outside permit tcp host frogman2 host 10.75.32.24 eq 8443 access-list acl_outside permit tcp host frogman3 host 10.75.32.24 eq 8443 access-list acl_outside permit tcp any host 10.75.32.23 eq smtp access-list acl_outside permit tcp any host 10.75.32.23 eq ssh access-list acl_outside permit tcp any host 10.75.32.24 eq ssh access-list acl_acad permit icmp any any echo-reply access-list acl_acad permit icmp any any unreachable access-list acl_acad permit icmp any any time-exceeded access-list acl_acad permit tcp any 10.0.0.0 255.0.0.0 eq www access-list acl_acad deny tcp any any eq www access-list acl_acad permit tcp any 10.0.0.0 255.0.0.0 eq https access-list acl_acad permit tcp any 10.0.0.0 255.0.0.0 eq 8080 access-list acl_acad permit tcp host 172.16.102.5 host 10.64.1.115 eq smtp pager lines 24 logging console debugging mtu outside 1500 mtu inside 1500 mtu academic 1500 ip address outside outsideIF 255.255.252.0 no ip address inside ip address academic acadIF 255.255.0.0 ip audit info action alarm ip audit attack action alarm pdm history enable arp timeout 14400 global (outside) 1 10.75.32.21 nat (academic) 1 acadNET 255.255.0.0 0 0 static (academic,outside) 10.75.32.22 Mail-Local netmask 255.255.255.255 0 0 static (academic,outside) 10.75.32.30 172.30.30.36 netmask 255.255.255.255 0 0 static (academic,outside) 10.75.32.23 172.16.102.5 netmask 255.255.255.255 0 0 static (academic,outside) 10.75.32.24 172.16.102.6 netmask 255.255.255.255 0 0 static (academic,outside) 10.75.32.25 172.16.102.8 netmask 255.255.255.255 0 0 access-group acl_outside in interface outside access-group acl_acad in interface academic route outside 0.0.0.0 0.0.0.0 10.75.32.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00 timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute aaa-server TACACS+ protocol tacacs+ aaa-server RADIUS protocol radius aaa-server LOCAL protocol local snmp-server host outside 172.31.10.153 snmp-server host outside 172.31.10.154 snmp-server host outside 172.31.10.155 no snmp-server location no snmp-server contact snmp-server community CPQ_HHS no snmp-server enable traps floodguard enable telnet 172.30.31.0 255.255.255.0 academic telnet timeout 5 ssh timeout 5 console timeout 0 terminal width 120 Cryptochecksum:hi2u : end PIX515#

  Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >