Search Results

Search found 6497 results on 260 pages for 'usb appliance'.

Page 15/260 | < Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >

• USB sound device not recognized

  - by David E. Anderson

  I have a USB sound device that used to work back when I ran other versions of Ubuntu. Now I can only partially see the device. I have tried many things I saw in Google searches, but none solve my problem. cat /proc/asound/cards sees the device as card 0 aplay -l shows C-Media USB Audio as card 0 alsamixer sees the device asoundconf list does not show the device sound preferences shows no hardware asoundconf-gtk set the device to pulseaudio, but fails with python errors ending in ValueError: too many values to unpack in the function set_default_card. I think this is the cause of my problem. The device is a Sony virtual phones wireless headphone amplifier.

  Read the article

• trying live-usb 12.04.1 image on an old desktop

  - by 213441265152351

  I am trying to load Ubuntu 12.04.1 32-bit desktop image on an old desktop computer. The system shows the initial menu, but after a while, I get an error like the one in the following two screenshots (it takes a few seconds to go from one to the other in the screen): I tried to load it using the different USB ports at the back of the computer, just in case, and I get basically the same error. Find another screenshot from another try: Any ideas what might be happening? NOTES: I checked the md5sum of the iso file to be e235b63c02644e219b7bf3668f479c9e *ubuntu-12.04.1-desktop-i386.iso. I did the 'Test' on the laptop where I created the USB drive, and it loads up correctly. The desktop computer in question is an old AMD Duron 1800MHz with 512MB RAM. I ran a memtest on the computer, and all went fine.

  Read the article

• How to connect Samsung Galaxy S3 via USB?

  - by dez93_2000

  Connecting as either MTP or PTP: neither allows one to see pictures saved as default by phone camera to DCIM folder on external SD card. Similar problems with previous models (e.g. S2) were solvable by 'usb utilities' in wireless & networking settings, but this is no longer present. Other suggestions have mentioned uninstalling various libraries... but I don't wanna just start cutting stuff without knowing it'll help. Any thoughts on how to mount a Samsung Galaxy S3 over USB?

  Read the article

• How to simulate a USB plug?

  - by Nicolas Delvaux

  I have an app that implements some automations when an USB key is plugged. While developing, I have to test it in a specific environment (derivative from Debian Squeeze). The app subscribe to HAL events via DBUS. The problem is: my desk is on the third floor while my test machines are in the basement. I would really like to have a way to simulate a USB plug. usbip does not work on Ubuntu. I can't manage to use the g_mass_storage module on Ubuntu (I lack the dummy_hcd module) and in Debian. Maybe it is possible to simulate a dbus call? My work station is on Ubuntu 12.04.

  Read the article

• USB Storage Device Automount

  - by matto1990

  Under Ubuntu 10.04 one of the problems which appeared is that USB devices would no longer automatically mount when plugged in. Normally I would get a pop up message asking what application I wanted to open the newly plugged in device with, however now that doesn't happen. This happens regardless of the way the device is formatted (NTFS or FAT32) and all other USB devices (printer, keyboard and mouse) work perfectly. My current solution is the mount them manually using sudo mount dev/... /medai/... however to be honest I'm just getting tired of having to do this. I'm happy to post any extra information you are likely to need. I know there will be lots of places I could look to find out what's going wrong but I have no idea where to start really.

  Read the article

• Make a live USB of your installed ubuntu

  - by Eray Tuncer

  Okay let me clear my point. Lets assume I want to make a internet cafe-like system. Every user will be able to enter via only one user account to linux. However, I do not want them to leave anything behind. Whenever this ubuntu is booted, I want to this system remove their garbage. Why I mentioned the live USB is that I have seen that live usb or cd makes what I want but not exactly because I want to install some apps on it and make some confugration like firewall, permissions.

  Read the article

• USB (wireless) keyboard not recognised during install

  - by Jon C

  I'm just trying my first trip into the world of Ubuntu. Trying to install from CD on to a virgin machine, I get the initial language prompt, select 'English', I get the Ubuntu install options, select 'Install Ubuntu Server'. I'm then presented with a further 'Language for installation' screen. At this point my keyboard stops working...! Some specifics: I'm using a Logitech wireless USB keyboard - it works fine on another machine; Machine is a ProLiant Micorserver N54L (No PS/2 ports); BIOS USB support is set to Legacy. Any ideas...? Thanks, Jonathan

  Read the article

• usb keyboard works except in terminal window (SOLVED)

  - by matrixunloaded

  I just installed 12.10 (clean install and updates). USB keyboard and mouse work fine EXCEPT the keyboard does not work in a terminal window (USB mouse is working in terminal). keyboard is Logitech MK320 and associated mouse. I'm typing in a mozilla window on the keyboard at this very moment and when I switch to the terminal window, nothing can be typed. Any ideas? I use terminal mode alot. Thanks matrixunloaded I didn't realize passwords do not show even an asterisk in terminal mode! I'd just installed 12.10 and was pasting a long sudo command and then typing my password (which looked like nothing appearing)

  Read the article

• UBUNTU 11.10 will not boot after suggesfully installed on 8GB usb 3.0 pendrive

  - by Oldrifle

  UBUNTU 11.10 on 8GB USB 3.0 pendrive. Drive Partitioned using gparted. 4GB BASE 3GB Home 600MB swap Installation Ok. Restart blinking cursor. Installed another distro on another USB 3.0 stick. It boots OK. --------------- DEBUG -------------------------------------- Boot Other distro and check: I compare boot file with another linux. grub of ubuntu is 1.4mb contend is different. Taken photo with mobile camera but can not add here. Files has note(music) sign on it. Downloaded 11.10 desktop and Installed. Same result. Will download 12.x when ready and try. Ready to try any suggstion. Orhan

  Read the article

• USB Mouse stutters periodically

  - by greggory.hz

  I'm using an HP dv6000 (not sure of exact model) with a pretty basic Logitech wireless laptop mouse. From time to time, the USB mouse will be very stuttery and less responsive. Not all clicks register and the motion is not smooth. It seems like it's related to the notify-osd coming up when I get an IM or Email or whatever else, but it happens other times as well. It's not the whole computer becoming less responsive, because if I use the touch pad during one of these fits, it works perfectly smooth. I've replaced the batteries in the mouse and have tried different USB ports with better line of sight, etc. I can't figure out what's going on. Any thoughts?

  Read the article

• Machine check error while booting from USB

  - by javanna

  I put the last Ubuntu iso on my USB stick using UNetBootin, after formatting it to fat32. I've already done that before with other operating systems and it worked. I can't actually boot Ubuntu from USB since I get a black screen with the error "Machine check error" on top the an automatic reboot happens. The error appears right after the boot, I can't see anything else before. I'm using my ASUS K53SV latop. Does anybody know how to solve this?

  Read the article

• UBUNTU 11.10 will not boot after succesfully installed on 8GB usb 3.0 pendrive

  - by Oldrifle

  UBUNTU 11.10 on 8GB USB 3.0 pendrive. Drive Partitioned using gparted. 4GB BASE 3GB Home 600MB swap Installation Ok. Restart blinking cursor. Installed another distro on another USB 3.0 stick. It boots OK. --------------- DEBUG -------------------------------------- Boot Other distro and check: I compare boot file with another linux. grub of ubuntu is 1.4mb contend is different. Taken photo with mobile camera but can not add here. Files has note(music) sign on it. Downloaded 11.10 desktop and Installed. Same result. Will download 12.x when ready and try. Ready to try any suggestion.

  Read the article

• 12.04 cannot boot from USB

  - by GhostRider

  The HP Pavilion g6 notebook is unable to boot from bootable USB stick created with Linux Live USB Creator. I was able to boot other systems using the same pendrive. I have changed the boot priority using F10. When I restarted, it didn't ask for any message like Press any key to boot from When I press F19, and selected the pendrive from the available options to boot from, while restarting it gives me a message: error while trying to boot selected boot image Though I looked into the possible suggestions here, none of them worked. Looking for any help? EDIT: I was able to fix the first issue, i'e ubuntu could be installed as secure boot option in the bios was not allowing the pendrive or cd/dvd to be detected. Now once i have successfully installed ubuntu 12.04, after the restart i was unable to find it in the os menu for selection and windows8 loaded by default Ubuntu version: 12.04

  Read the article

• USB keyboard hit and miss as to whether it will work on boot-up

  - by user208745

  I am new to Ubuntu. Have installed 12.04 on a slave drive while I migrate. Usually booting into Ubuntu goes without a hitch but recently I often find I am unable to use the keyboard, and log-in using the on-screen KB. Sometimes if I remove the USB jack & re-connect it will start working again but not always. I do have an old PS/2 KB which I am using at the moment but.......has anyone any ideas on how to get the USB KB reliably connected? Thanks Dave

  Read the article

• Usb/vga not recognized anymore

  - by Peter Raeves

  I don't know what happened, but yesterday everything worked fine, but when I woke up this morning and booted my computer to Ubuntu 14.04 a bunch of hardware isn't recognized anymore. I use a dual monitor setup with dvi-d and vga, but the vga screen isn't recognized anymore and the dvi-d monitor is recognized as "Built-in Display" while I'm not on a laptop. Also every device connected through usb isn't recognized anymore either. I have a keyboard with the blue round connector, which still works, so I can still log in though. The computer goes slower than usual and I have no idea what has happened. Can anybody point me in the direction I should start looking, because this is scary! I just checked and both the front and back sound connectors stopped working also :/ Edit: The devices connected through USB are recognized as they all show up using sudo lsusb, Ubuntu just doesn't let me use them anymore.

  Read the article

• Ubuntu Doesn't Start from USB After Installation

  - by Fred Venus

  My computer refuses to boot from the USB even after I change everything that I can possibly think of on my motherboard's BIOS. But I have booted from the USB twice in the past. The first time is when I first got the computer and needed to install a new operating system. The second time is when I installed Windows onto the whole hard drive and needed to reinstall Ubuntu. It seems that it only refuses to boot if there is already an existing installation of Ubuntu on the hard drive. Any ideas on what is going on?

  Read the article

• 12.04 LTS usb wont boot

  - by Niva

  I've tried to install ubuntu 12.04 LTS parallel with Windows 8, on my laptop Clevo m767yu But when I try to boot from USB it just stops when it's trying to read the files. it stops and shows this picture: https://www.dropbox.com/s/np3ptvvmasv7ax2/IMAG0097.jpg If I try to boot from a cd, it stops and shows a cursor blinking. I've tried both usb and cd on other computers, and the both works. I've a little experience with Ubuntu, but I have never had problems with the installing process. Any help will be appreciated!

  Read the article

• Cannot boot from USB to install 12.10

  - by Ramzi Njeim

  i am a long time user of Ubuntu and this is the first time a such thing happens to me. I usually upgrade from a version to an other, but this time i wish to do a clean install. I want to totally remove my 12.04 and do a clean install of 12.10, i created a live USB then i restarted my computer to boot from USB, i got the following error: Product is covered by one or more of the following patents: US5,434,872, US5,732,894, (and many more) Under that i see: PCIe GBE Family Controller Series v2.38 Media test failiure Exiting PXE ROM And then it reboots I've searched a lot for an answer, i guess the problem is with something in my bios, but i didn't find a fix. I would really appreciate a fix for my problem. My laptop is a Toshiba p775 dual boot ubuntu 12.04 and windows 7.

  Read the article

• True live USB: Fully Functional

  - by jhewitt3476

  I can't seem to have the affect I'm looking for on a "Live Ubuntu" I want to run it from the USB drive, a fully functional, fully upgradable version. I do not want to use as a "trial version", or to set up a dual boot or run in a virtual system. I have kids that are killing my computer & everything on my HD, they need their own OS & drive but don't have the $$$ for a laptop for them, I just want it to work on the USB the same way it works on the C: drive

  Read the article

• Can I get an adapter for usb 3.0 to gigabit, or a gigabit switch with usb 3.0?

  - by techaddict

  Basically I want to be able to attach USB 3.0 external portable hard drives to my network and maintain at least gigabit speeds. I can think of four ways to do this, two of which I know exist: 1) NAS - get an NAS which features USB 3.0 and gigabit 2) Gigabit router with a USB 3.0 port and I want to know if these two exist: 3) gigabit switch (multiple gigabit ports) with at least one USB 3.0 port 4) USB 3.0 to gigabit adapter The gigabit adapter would be similar to this: http://www.addonics.com/products/nas30u2.php except that that is only USB 2.0 so it is not true gigabit, as gigabit is 125MBps but USB 2.0 is only 60MBps, so that adapter only has a maximum transfer speed of 60MBps and the "gigabit" is practically useless.

  Read the article

• Motherboard/PSU crippling USB and Sata

  - by celebdor

  I very recently bought a new desktop computer. The motherboard is: Z77MX-D3H and the power supply is ocz zs series 550w. The issue I have is that once I boot to the operating system (I have tried with fedora and Ubuntu with kernels 2.6.38 - 3.4.0), my hard drive (2.5" Magnetic) occasionally makes a power switch noise and it resets. Needless to say, when this drive is the OS drive, the OS crashes. I also have a SSD that works fine with the same OS configurations, but if I have the magnetic hard drive attached as second drive, it works erratically and the reconnects result in corrupted data. I also noticed that whenever I plug an external hard drive USB2.0 or USB3.0 to the computer the issue with the reconnects is even worse: [ 52.198441] sd 7:0:0:0: [sdc] Spinning up disk... [ 57.955811] usb 4-3: USB disconnect, device number 3 [ 58.023687] .ready [ 58.023914] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.023919] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.023932] sd 7:0:0:0: [sdc] Sense not available. [ 58.024061] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024063] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024064] sd 7:0:0:0: [sdc] Sense not available. [ 58.024099] sd 7:0:0:0: [sdc] Write Protect is off [ 58.024101] sd 7:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 58.024135] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024137] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024400] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.024402] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024405] sd 7:0:0:0: [sdc] Sense not available. [ 58.024448] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024450] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024451] sd 7:0:0:0: [sdc] Sense not available. [ 58.024469] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024471] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024472] sd 7:0:0:0: [sdc] Attached SCSI disk [ 58.407725] usb 4-3: new SuperSpeed USB device number 4 using xhci_hcd [ 58.424921] scsi8 : usb-storage 4-3:1.0 [ 59.424185] scsi 8:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 59.424406] scsi 8:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 59.425098] sd 8:0:0:0: Attached scsi generic sg2 type 0 [ 59.425176] ses 8:0:0:1: Attached Enclosure device [ 59.425248] ses 8:0:0:1: Attached scsi generic sg3 type 13 [ 61.845836] sd 8:0:0:0: [sdc] 976707584 512-byte logical blocks: (500 GB/465 GiB) [ 61.845838] sd 8:0:0:0: [sdc] 4096-byte physical blocks [ 61.846336] sd 8:0:0:0: [sdc] Write Protect is off [ 61.846338] sd 8:0:0:0: [sdc] Mode Sense: 47 00 10 08 [ 61.846718] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.846720] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.848105] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.848106] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.857147] sdc: sdc1 [ 61.858915] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.858916] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.858918] sd 8:0:0:0: [sdc] Attached SCSI disk [ 69.875809] usb 4-3: USB disconnect, device number 4 [ 70.275816] usb 4-3: new SuperSpeed USB device number 5 using xhci_hcd [ 70.293063] scsi9 : usb-storage 4-3:1.0 [ 71.292257] scsi 9:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 71.292505] scsi 9:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 71.293527] sd 9:0:0:0: Attached scsi generic sg2 type 0 [ 71.293668] ses 9:0:0:1: Attached Enclosure device [ 71.293758] ses 9:0:0:1: Attached scsi generic sg3 type 13 [ 73.323804] usb 4-3: USB disconnect, device number 5 [ 101.868078] ses 9:0:0:1: Device offlined - not ready after error recovery [ 101.868124] ses 9:0:0:1: Failed to get diagnostic page 0x50000 [ 101.868131] ses 9:0:0:1: Failed to bind enclosure -19 [ 101.868288] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868292] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868296] sd 9:0:0:0: [sdc] Sense not available. [ 101.868428] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868434] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868439] sd 9:0:0:0: [sdc] Sense not available. [ 101.868468] sd 9:0:0:0: [sdc] Write Protect is off [ 101.868473] sd 9:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 101.868580] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868584] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868845] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868849] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868854] sd 9:0:0:0: [sdc] Sense not available. [ 101.868894] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868898] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868903] sd 9:0:0:0: [sdc] Sense not available. [ 101.868961] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868966] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868969] sd 9:0:0:0: [sdc] Attached SCSI disk Now, if I plug the same drive to the powered usb 2.0 hub of my monitor, the issue is not reproduced (at least on a 20h long operation). Also the issue of the usb reconnects is less frequent if the hard drive is plugged before I switch on the computer. Does anybody have some advice as to what I could do? Which is the faulty part/s that I should replace? As for me, I really don't know if to point my finger to the PSU or the Motherboard (I have updated to the latest firmware and checked the BIOS settings several times). EDIT: The reconnects are happening both in the Sata connected drives and the USBX connected drives.

  Read the article

• In 10.10, USB 3.0 PCI Express card recognized by lspci but not lsusb or dmesg. How to fix?

  - by Paul

  Asus N PC, runs 10.10 x86_64 The Asus N comes with 4 usb 2.0 ports, each labelled 2.0 on the case. Attempting to add two usb 3.0 ports to be provided by a generic usb 3.0 pci express card installed in the pci expres slot. The new card says usb 3.0 and has the blue ports. The card is installed into the laptop unpowered, then the laptop is powered on and boots normally. Nothing happens when a USB 3.0 flash drive is inserted into the usb 3.0 port. uname -a Linux drpaulbrewer-N90SV 2.6.35.8 #1 SMP Fri Jan 14 15:54:11 EST 2011 x86_64 GNU/Linux lspci -v 00:00.0 Host bridge: Silicon Integrated Systems [SiS] 671MX Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64 Kernel modules: sis-agp 00:01.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fa000000-fdefffff Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [f4] Power Management version 2 Capabilities: [70] Subsystem: Silicon Integrated Systems [SiS] PCI-to-PCI bridge Kernel driver in use: pcieport 00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] (rev 01) Flags: bus master, medium devsel, latency 0 00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev 01) (prog-if 80 [Master]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 128 I/O ports at 01f0 [size=8] I/O ports at 03f4 [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=1] I/O ports at ffe0 [size=16] Capabilities: [58] Power Management version 2 Kernel driver in use: pata_sis 00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 20 Memory at f9fff000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 21 Memory at f9ffe000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 22 Memory at f9ffd000 (32-bit, non-prefetchable) [size=4K] Capabilities: [50] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter (rev 02) Subsystem: ASUSTeK Computer Inc. Device 11f5 Flags: bus master, medium devsel, latency 0, IRQ 19 Memory at f9ffcc00 (32-bit, non-prefetchable) [size=128] I/O ports at cc00 [size=128] Capabilities: [40] Power Management version 2 Kernel driver in use: sis190 Kernel modules: sis190 00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA Controller / IDE mode (rev 03) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: ASUSTeK Computer Inc. Device 1b27 Flags: bus master, medium devsel, latency 64, IRQ 17 I/O ports at c800 [size=8] I/O ports at c400 [size=4] I/O ports at c000 [size=8] I/O ports at bc00 [size=4] I/O ports at b800 [size=16] I/O ports at b400 [size=128] Capabilities: [58] Power Management version 2 Kernel driver in use: sata_sis Kernel modules: sata_sis 00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: fdf00000-fdffffff Capabilities: [b0] Subsystem: Silicon Integrated Systems [SiS] Device 0004 Capabilities: [c0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [f4] Power Management version 2 Kernel driver in use: pcieport 00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=06, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fe000000-febfffff Prefetchable memory behind bridge: 00000000f6000000-00000000f8ffffff Capabilities: [b0] Subsystem: Silicon Integrated Systems [SiS] Device 0004 Capabilities: [c0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Root Port (Slot+), MSI 00 Capabilities: [f4] Power Management version 2 Kernel driver in use: pcieport 00:0f.0 Audio device: Silicon Integrated Systems [SiS] Azalia Audio Controller Subsystem: ASUSTeK Computer Inc. Device 17b3 Flags: bus master, medium devsel, latency 0, IRQ 18 Memory at f9ff4000 (32-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 01:00.0 VGA compatible controller: nVidia Corporation G96 [GeForce GT 130M] (rev a1) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 2021 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fc000000 (32-bit, non-prefetchable) [size=16M] Memory at d0000000 (64-bit, prefetchable) [size=256M] Memory at fa000000 (64-bit, non-prefetchable) [size=32M] I/O ports at dc00 [size=128] [virtual] Expansion ROM at fde80000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Kernel driver in use: nvidia Kernel modules: nvidia-current, nouveau, nvidiafb 02:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Device 1a3b:1067 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fdff0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Kernel driver in use: ath9k Kernel modules: ath9k 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at febfe000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable- Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 lsusb Bus 003 Device 002: ID 0b05:1751 ASUSTek Computer, Inc. BT-253 Bluetooth Adapter Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 004: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 001 Device 002: ID 04f2:b071 Chicony Electronics Co., Ltd 2.0M UVC Webcam / CNF7129 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub dmesg trying to post dmesg exceeded the stackexchange posting limit of 30K... but nothing there is usb 3.0

  Read the article

• Creating a bootable flash without overlayfs

  - by Septagram

  I want to create an USB stick to carry my Ubuntu everywhere around with me. It's not intended to spread Ubuntu by installing it everywhere, but rather for running my configured system on any computer I come across. So far, I went with installing Ubuntu with unetbootin, however, I have some issues with this. When installed with netbootin, the original disk image is kept intact on the flash drive, forever. Also, a file is created for persistent storage and during boot it is accessed together with the image by overlayfs. This, in my opinion, has the following problems: If system is updated regularly, then files from the image are overwritten in persistent storage, doubling their size and wasting precious space. Persistent storage has a fixed size that you have to define from the start, again, wasting precious space. I'm not 100% sure, but maybe using overlayfs makes disk access slower, and more so on the relatively slow devices. So I'd like to find another solution: either to get rid of the original image or to install Ubuntu "normally" on the separate ext2 partition, or maybe even install it in the main vfat partition on the USB stick. Suggestions?

  Read the article

• Getting file system free space

  - by Fred Riley

  This isn't a problem as such, more a request for information based on ignorance of the Linux filesystem. The very short question is: How do I find out how much free and used space there is on the volume from which Ubuntu is running? More detail: I'm running Ubuntu 12.04 from a 64Gb USB3 stick, created from booting up a year-old Ubuntu 12.04 DVD and running Startup Disk Creator. The reason for this is that the Master Boot Record on my hard disk, holding Windoze 7, has gone belly-up, and whilst awaiting a recovery disk I'm running Ubunto off USB or DVD as a 'trial'. (And will continue to run Ubuntu after restoring Windoze, as I've rediscovered my love of the penguin :o)) After installing Ubuntu on the stick I ran the software update app, which downloaded some 450Mb of updates and took a couple of hours to install to the stick. A couple of times I got a message saying that disk space was short. So I looked in the file manager (or whatever it's called these days) and couldn't see the stick listed, just: SYSTEM hard disk (listed as 479Gb Filesystem) two other partitions that had been created by Windoze "4.3GB Filesystem" which when I try to open gives the error "Could not find /cow", and when I try to unmount it tells me I can't because it's not mounted - D'OH!! Edit: screenshot of file manager Edit: screenshot of low disk space warning What I can't see is the USB stick from which I'm running Ubuntu. Where's it gone, anybody know? This is tangentially related to a previous question of mine about system tools, in that I'm trying to get control and knowledge of the system in the newest incarnation of Ubuntu.

  Read the article

• usb_modeswitch not switching

  - by deniz

  After I upgraded from kernel 2.6.18 to 3.5.3 modeswitch started not to work for me. Although lsusb shows my usb modem, usb_modeswitch does not switch it. My system information is like below. I ran lsusb, dmesg, usb-devices and usb_modeswitch their output is like below. usb_modeswitch instead of switching my modem it says "No devices in default mode found. Nothing to do. Bye.". Can you offer a solution? Kernel: Linux 3.5.3 usb_modeswitch: 1.2.3-1 usb_modeswitch-data: 20120120-1 usbutils: 006-1 libusb: 1.0.8-0.1 root@localhost$ lsusb Bus 002 Device 029: ID 12d1:1446 Huawei Technologies Co., Ltd. root@localhost$ dmesg [70112.477080] usb 2-1.4: new high-speed USB device number 30 using ehci_hcd [70112.567757] scsi49 : usb-storage 2-1.4:1.0 [70112.567842] scsi50 : usb-storage 2-1.4:1.1 [70113.571433] scsi 49:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 [70113.572304] scsi 50:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2 [70113.574169] sr0: scsi-1 drive [70113.574223] sr 49:0:0:0: Attached scsi CD-ROM sr0 [70113.574250] sr 49:0:0:0: Attached scsi generic sg1 type 5 [70113.574350] sd 50:0:0:0: Attached scsi generic sg2 type 0 [70113.577173] sd 50:0:0:0: [sdb] Attached SCSI removable disk root@localhost$ usb-devices T: Bus=02 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#= 30 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=1446 Rev=00.00 S: Manufacturer=Huawei Technologies S: Product=HUAWEI Mobile C: #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage root@localhost$ cat /etc/usb_modeswitch.d/12d1\:1446 # Huawei, newer modems TargetVendor= 0x12d1 TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" MessageContent="55534243123456780000000000000011062000000100000000000000000000" root@localhost$ usb_modeswitch -c /etc/usb_modeswitch.d/12d1:1446 -v 12d1 -p 1446 -W * usb_modeswitch: handle USB devices with multiple modes * Version 1.2.3 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above) ! PLEASE REPORT NEW CONFIGURATIONS ! DefaultVendor= 0x12d1 DefaultProduct= 0x1446 TargetVendor= 0x12d1 TargetProduct= not set TargetClass= not set TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243123456780000000000000011062000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set InquireDevice enabled (default) Success check disabled System integration mode disabled usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Skipping non bus directory devices usb_os_find_busses: Skipping non bus directory drivers usb_os_find_busses: Skipping non bus directory uevent usb_os_find_busses: Skipping non bus directory drivers_probe usb_os_find_busses: Skipping non bus directory drivers_autoprobe Looking for target devices ... No devices in target mode or class found Looking for default devices ... No devices in default mode found. Nothing to do. Bye. Thanks in advance.

  Read the article

< Previous Page | 11 12 13 14 15 16 17 18 19 20 21 22  | Next Page >