Search Results

Search found 12992 results on 520 pages for 'box'.

Page 150/520 | < Previous Page | 146 147 148 149 150 151 152 153 154 155 156 157  | Next Page >

• Debian and Multipath IO problem

  - by tearman

  Basically the situation is, I have a box running Debian, the box internally has an Intel SCSI RAID controller which is controlling 2 hard drives in RAID1 mode which is where the OS is installed. Further, I have a QLogic fiber channel adapter that connects the unit to a Fiber Channel SAN. My process of installation is I'll install Debian to the local drives, and leave the QLogic firmware out of it for the time being. Then once I get the unit online, I'll install the firmware drivers. This flops my internal drives from /dev/sda to /dev/sdc, which is a bit annoying, but recoverable. Probably should address these by UUID anyways. Once I get back online, I have to install multipath-tools (the framework is a multipath framework). However, once I reboot the machine again, it fails on boot after discovering multipath targets, saying my local drives are busy and cannot be mounted to /root. Any help in what may be the problem here? Or at least how to disable multipath until after the unit boots and then ignores the internal drives?

  Read the article

• Zimbra MTA settings

  - by user192702

  Hi have some questions for Zimbra v8.0.6GA. Under Configure - MTA - Network, I'm seeing a few settings and am not very clear what to do with them. Web mail MTA Host name Is this for delivering local mail only (ie not for external mails)? According to this link, it says the following. That's a mouthful but what is "composed messages"? Is this for a multi server deployment where the Postfix server for Zimbra isn't installed on the same box that as the rest of the servers? Webmail MTA is used by the Zimbra server for composed messages and must be the location of the Postfix server in the Zimbra MTA. Relay MTA for external delivery My understanding after reading the doc is that if my ISP doesn't force me to relay outgoing mails through them, and I have enabled DNS lookup, I can leave this blank? Inbound SMTP host name Sorry I know this is explained as "If your MX records point to a spam-relay or any other external non-Zimbra server, enter the name of that server in the Inbound SMTP host name field." but I'm not following. Can someone provide an example? MTA Trusted Networks The admin doc says "To set up MTA trusted networks on a per server basis, make sure that MTA trusted networks have been set up as global settings and then go the Configure Servers MTA page and in the MTA Trusted Networks field enter the trusted network addresses for the server." However I see out of the box it has default networks setup for the server whereas on a global level it's blank. Does this mean there is a bug with the install software and I have to copy the setting from the server to the global setting?

  Read the article

• 16-bit MS-DOS Subsystem: csrss.exe

  - by Wesley

  Hi all, I just booted up my Samsung N120 netbook (with Windows XP Home SP3) and a dialog box came up with a command prompt window behind it. The dialog box is titled 16 bit MS-DOS Subsystem and the message is as follows: C:\DOCUME~1\SAMSUNG\csrss.exe The NTVDM CPU has encountered an illegal instruction. CS:0544 IP:0117 OP:63 00 64 00 34 Choose 'Close' to terminate the application. This only started on my most recent boot-up. One thing to note is that when I downloaded the Dropbox installer and opened it up, Panda Cloud Antivirus detected a suspicious file, which was csrss.exe and "neutralized it." However, an actual virus or trojan was not detected immediately before the file was detected and neutralized. Just under two weeks ago, a trojan and two viruses were detected for some odd reason. (I only went to website I knew and I do not torrent or browse adult sites.) Anyhow, the two viruses came up in temporary files and the trojan was "neutralized." Anyways, the main question is: How can I repair the csrss.exe file such that Windows XP starts up properly? A screenshot could be posted upon request. Thanks in advance!

  Read the article

• How do I add a VMware ESXi Host to Microsoft Virtual Machine Manager?

  - by user63250

  I am trying to manage virtual machines running on a VMware ESXi host using Microsoft System Center Virtual Machine Manager. I was able to add the ESXi machine using the "Add VMware VirtualCenter server" option, but can't access any of the VMs on the datastore associated with this ESXi server. The datastore of the ESXi box is showing up with the correct name, but it won't let me see any of the VMs that have already been created; I get "There are no virtual machines on this host." Because I couldn't get any of the existing virtual machines to show up, I tried creating some new ones. When using VMM to connect to ESXi and create new VMs, I get the following error messages in the "rating explanation" section: The virtualization software on the selected host does not support virtual hard disks on an IDE bus. and The virtualization software on the host XXXXXX does not support the creation of dynamic virtual hard disk. Any ideas on why I can't manage existing machines and why I can't create new ones? The existing machines were created in vSphere. I should note that the ESXi server and the server running SCVMM are both on the same domain. I should also note that although the ESXi box has been added as a VirtualCetner server, when I try to add it through the "Add Host" option, I get an error message saying "Virtual Machine Manager cannot complete the VirtualCenter action on server EXSi because of the following error: The operation is not supported on the object."

  Read the article

• Openconnect for Cisco VPN doesn't recognize private key file - asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag

  - by Alexander Skwar

  I'm trying to use my Synology DS212 NAS box also act as VPN gateway to my companies VPN. Sadly, they only use Cisco ASA and to complicate stuff even further, we've got to use personal certificates (which is of course more secure, but more complicate to get going…). So I compiled OpenConnect v4.06 from http://www.infradead.org/openconnect/. As a very basic test, I tried to build a connection by manually invoking openconnect, passing along the key and cert files, like so: /lib/ld-linux.so.3 --library-path /opt/lib \ /opt/openconnect/sbin/openconnect \ --certificate=$VPN_CFG/alexander.crt \ --sslkey=$VPN_CFG/alexander.key \ --cafile=$VPN_CFG/Company_VPN_CA.crt \ --user=alexander --verbose <ip>:443 It fails :( Attempting to connect to <ip>:443 Using certificate file $VPN_CFG/alexander.crt Using client certificate '/[email protected]/OU=Company VPN' 5919:error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag:tasn_dec.c:1315: Loading private key failed (see above errors) Loading certificate failed. Aborting. Failed to open HTTPS connection to <ip> Failed to obtain WebVPN cookie When I run the same command with the same cert/key files on a Ubuntu 12.04 box, it works: openconnect \ --certificate=$VPN_CFG/alexander.crt \ --sslkey=$VPN_CFG/alexander.key \ --cafile=$VPN_CFG/Company_VPN_CA.crt \ --user=alexander --verbose <ip>:443 Attempting to connect to <ip>:443 Using certificate file $VPN_CFG/alexander.crt Extra cert from cafile: '/CN=Company AG VPN CA/O=Company AG/L=Zurich/ST=ZH/C=CH' SSL negotiation with <ip> Server certificate verify failed: self signed certificate Certificate from VPN server "<ip>" failed verification. Reason: self signed certificate Enter 'yes' to accept, 'no' to abort; anything else to view: yes Connected to HTTPS on <ip> GET https://<ip>/ […] Well… The error on the NAS is this: 5919:error:0D0680A8:asn1 encoding routines:ASN1_CHECK_TLEN:wrong tag:tasn_dec.c:1315: Any ideas, what's causing this? On Syno, I use OpenConnect 4.06. On Ubuntu, I just compiled and installed to a custom location OpenConnect 4.06 as well. Thanks, Alexander

  Read the article

• port forwarding with VirtualBox

  - by Argh

  I have a virtualbox VM running ubuntu. The Ubuntu guest is running a web server which listens on port 3000 (http://127.0.0.1:3000) The host machine is windows vista. I have configured port forwarding using VBoxManage. If I query the config using VboxManage getextradata "MyMachine", I get Key: GUI/AutoresizeGuest, Value: on Key: GUI/Fullscreen, Value: off Key: GUI/LastCloseAction, Value: shutdown Key: GUI/LastWindowPostion, Value: 9,34,640,529,max Key: GUI/MiniToolBarAlignment, Value: bottom Key: GUI/MiniToolBarAutoHide, Value: off Key: GUI/SaveMountedAtRuntime, Value: yes Key: GUI/Seamless, Value: off Key: GUI/ShowMiniToolBar, Value: yes Key: VBoxInternal/Devices/pcnet/0/LUN#0/Config/guesthttp/GuestPort, Value: 3000 Key: VBoxInternal/Devices/pcnet/0/LUN#0/Config/guesthttp/HostPort, Value: 3000 Key: VBoxInternal/Devices/pcnet/0/LUN#0/Config/guesthttp/Protocol, Value: TCP This looks like it should work... However when I try to access the web server from the host machine (windows box) I dont get a response. I ran a netstat on the windows box and nothing appears to be listening on port 3000 which explains why forwrding isnt working. Note that I have already tested with my firewall switched off... The version of VirtualBox I am using is 3.1.4 Any ideas?

  Read the article

• monitoring a /21 for potential bad guys with snort and port mirroring

  - by Adeodatus

  Hi all, I want/need to start monitoring our network a bit better. Its an odd network in that it comprises 2 /22 public IPs and a slew of private admin IPs. I do have one point in the network where it all comes together and I can turn on port mirroring on the catalyst. From that port, I'd like to turn up a box running various utilities. Snort is high on my list but it'd be nice to also get some networking statistics with something like Netflow. So, what are peoeple's thoughts. I can turn up a box needed for this with a bit of ease. We have the hardware available. What should I run? I'd love to know what kind of nasty things are potentially going on but I'd also like to see statistics on what people are doing on the network so I can better tweak our systems to handle it better and improve performance. I'm open so please, give me some ideas to go along with what I've got.

  Read the article

• pfsense 2.0.1 Firewall SMB Share not showing up under network

  - by atrueresistance

  I have a freenas NAS with a SMB share running at 192.168.2.2 of a 192.168.2.0/28 network. Gateway is 192.168.2.1. Originally this was running on a switch with my LAN, but now having upgraded to new hardware the Freenas has it's own port on the firewall. Before the switch the freenas would show up under Network on a windows 7 box and an OSX Lion box as freenas{wins} or CIFS shares on freenas{osx} so I know it doesn't have anything do to with the freenas. Here are my pfsense rules. ID Proto Source Port Destination Port Gateway Queue Schedule Description PASS TCP FREENAS net * LAN net 139 (NetBIOS-SSN) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 389 (LDAP) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 445 (MS DS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 137 (NetBIOS-NS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 138 (NetBIOS-DGM) * none cifs lan passthrough BLOCK * FREENAS net * LAN net * * none BLOCK * FREENAS net * OPTZONE net * * none BLOCK * FREENAS net * 192.168.2.1 * * none PASS * FREENAS net * * * * none BLOCK * * * * * * none I can connect if I use \\192.168.2.2 and enter the correct login details. I would just like this to show up on the network. Nothing in the log seems to be blocked when I filter by 192.168.2.2. What port am I missing for SMB to show up under the network and not have to connect by IP? ps. Do I really need the LDAP rule?

  Read the article

• Linux Kernel Packet Forwarding Performance

  - by Bob Somers

  I've been using a Linux box as a router for some time now. Nothing too fancy, just enabling forwarding in the kernel, turning on masquerading, and setting up iptables to poke a few holes in the firewall. Recently a friend of mine pointed out a performance problem. Single TCP connections seem to experience very poor performance. You have to open multiple parallel TCP connections to get decent speed. For example, I have a 10 Mbit internet connection. When I download a file from a known-fast source using something like the DownThemAll! extension for Firefox (which opens multiple parallel TCP connections) I can get it to max out my downstream bandwidth at around 1 MB/s. However, when I download the same file using the built-in download manager in Firefox (uses only a single TCP connection) it starts fast and the speed tanks until it tops out around 100 KB/s to 350 KB/s. I've checked the internal network and it doesn't seem to have any problems. Everything goes through a 100 Mbit switch. I've also run iperf both internally (from the router to my desktop) and externally (from my desktop to a Linux box I own out on the net) and haven't seen any problems. It tops out around 1 MB/s like it should. Speedtest.net also reports 10 Mbits speeds. The load on the Linux machine is around 0.00, 0.00, 0.00 all the time, and it's got plenty of free RAM. It's an older laptop with a Pentium M 1.6 GHz processor and 1 GB of RAM. The internal network is connected to the built in Intel NIC and the cable modem is connected to a Netgear FA511 32-bit PCMCIA network card. I think the problem is with the packet forwarding in the router, but I honestly am not sure where the problem could be. Is there anything that would substantially slow down a single TCP stream?

  Read the article

• How can I view the binary contents of a file natively in Windows 7? (Is it possible.)

  - by Shannon Severance

  I have a file, a little bigger than 500MB, that is causing some problems. I believe the issue is in the end of line (EOL) convention used. I would like to look at the file in its uninterpreted raw form (1) to confirm the EOL convention of the file. How can I view the "binary" of a file using something built in to Windows 7? I would prefer to avoid having to download anything additional. (1) My coworker and I opened the file in text editors, and they show the lines as one would expect. But both text editors will open files with different EOL conventions and interpret them automagically. (TextEdit and Emacs 24.2. For Emacs I had created a second file with just the first 4K bytes using head -c4096 on a linux box and opened that from my windows box. I attempted to use hexl-mode in Emacs, but when I went to hexl-mode and back to text-mode, the contents of the buffer had changed, adding a visible ^M to the end of each line, so I'm not trusting that at the moment. I believe the issue may be in the end of line character(s) used. The editors my coworker and I tried (1) just automagically recognized the end of line convention and showed us lines. And based on other evidence I believe the EOL convention is carriage return only. (2) return only. are able to recognize and To know what is actually in the file, I would like to look at the binary contents of the file, or at least a couple thousand bytes of the file, preferablely in Hex, though I could work with decimal or octal. Just ones an zeros would be pretty rough to look at.

  Read the article

• Windows Server 2008 RAID10

  - by JT

  Hello All, I am building a storage system for myself. I have a 16 bay SATA chasis and right now I have 1 x 500GB SATA for booting 8 x 1.5TB for data. 3Ware 9500S-8 RAID card where these 8 drives above are connected to. I am used to linux, but not in the RAID department. I have Windows experience too. What I am looking for is something that I can just let sit, be reliable and use for other items as well. (Like running test websites, Apache, MySQL, etc). This box is private on a Class-C subnet. My thought is to at least consider Windows Server 2008. I especially like the potential for NON-GUI Mode. Can Windows Server 2008 do a Software RAID 10 out of the box? Software RAID is better performance and better in case the raid needs to be moved to another machine? I just want to SCP files, so OpenSSH running on it? Can one install the GUI, but not use it unless they get in a bind? Is Windows a good idea or should I stick to a Linux Software RAID or FreeBSD + ZFS?

  Read the article

• AWS lighttpd: Sending a copy of requests to test.

  - by Martin

  I have a load balanced service on AWS. So the ELB evenly distributes the load across my servers. Each server is running lighttpd that does logging and forwards the requests to my service (on the same machine). I have written a new version of the service. It is installed and running on an EC2 machine test1 (basically a mirror of our current server but the new service running instead of the original) and I have done some preliminary tests that look good. But what I would like to do is mirror a fraction of incoming traffic to the new version of the service so I can do some comparisons between an original version and the new version based on real traffic. Thus I was thinking I could modify one box behind the ELB to duplicate its traffic to the test1. I was thinking I could modify the configuration of lighttpd so that each request is mirrored/duplicated. i.e. the original service keeps responding as before but a mirror request is sent to test1 but the reply is just dropped). Unfortunately I have not been able to work this out. Any ideas on how I could mirror the requests from one box to itself and test1. Or any other ideas for testing.

  Read the article

• Using Virtualbox Bridge Networking fails connection from Guest OS to Oracle XE running on Host

  - by Licheng

  I am trying to make a JDBC connection from a VirtualBox Ubuntu Guest OS to an Oracle XE database running o Host. However, the connection is refused. Here are the details of my environment: VirtualBox: 4.1.4 Host OS: Windows 7 Guest OS: Ubuntu server 11.4 Networking mode: Bridged network Oracle XE database running on Host Issue: WebLogic server runs on the Ubuntu virtualbox. It attempts to connect to an Oracle XE database running on the Host OS (windows 7) with listening port 1521. On the Guest OS (Ubuntu), I am able to ping the Host computer from the Guest OS. However, when I configured a JDBC data source on the WebLogic server on the Guest OS to connect to the Oracle XE, connection took a long time, and eventually I received an "IO Exception: The Network Adapter could not establish the connection". When I tried "telnet host-ip 1521", no connection was established. With Bridge networking, I can make bi-directional connections between the host and the guest OS (e.g. connection through ssh and ftp). Is there anything I missed in the setup of Bridge networking and the guest/host OS? Note that I was able to make the same connection within a normal networking environment (i.e. not using virtual box). I am not sure whether Bridge networking is a good option for the work described above. Should I use host-only networking mode? If so, any specific configurations I need to perform? I read through the Virtual box document on setting up the host-only network, however, it lacks of details. I followed the procedures described in the manual, and couldn't even connect to the host. Could some experts here enlighten me on this issue? Much appreciated. Licheng

  Read the article

• SQL Server 2008 Remote Access

  - by Timothy Strimple

  I'm having problems connecting to my SQL Server 2008 database from my computer. I have enabled remote connections as described in this answer (http://serverfault.com/questions/7798/how-to-enable-remote-connections-for-sql-server-2008). And I have added the ports listed on the microsoft support page to our Cisco Asa firewall and I'm still unable to connect. The error I'm getting from the SQL Management Studio is: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: TCP Provider, error: 0 - A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.) (Microsoft SQL Server, Error: 10060) Once again, I have double and triple checked that remote connections are enabled under the database properties and that TCP is enabled on the configuration page. I've added tcp ports 135, 1433, 1434, 2382, 2383, and 4022 as well as udp 1434 to the firewall. I've also checked to make sure that 1433 is the static port that is set in the tcp section of the database server configuration. The ports should be configured correctly in the firewall since http/https and rdp are all working and the sql server ports are setup the same way. What am I missing here? Any help you could offer would be greatly appreciated. Edit: I can connect to the server via TCP on the internal network. The servers are colocated in a datacenter and I can connect from my production box to my development box and vice versa. To me that indicates a firewall issue, but I've no idea what else to open. I've even tried allowing all tcp ports to that server without success.

  Read the article

• NIS: which mechanism hides shadow.byname for unpriviledged users?

  - by Mark Salzer

  On some Linux box (SLES 11.1) which is a NIS client I can do as root: ypcat shadow.byname and get output, i.e. some lines with the encrypted passwords, amongst other information. On the same Linux box, if I run the same command as unpriviledged user, I get No such map shadow.byname. Reason: No such map in server's domain Now I am surprised. My good old knowlege says that shadow passwords in NIS are absurd because there is no access control or authentication in the protocol and thus every (unpriviledged) user can access the shadow map and thereby obtain the encrypted passwords. Obviously we have a different picture here. Unfortunately I don't have access to the NIS server to figure out what is happening. My only guess is that the NIS master gives the map only to clients conection from a priviledged port (1024), but this is only an uneducated guess. What mechanisms are there in current NIS implementations to lead to a behavior like the above? How "secure" are they? Can the be circumvented easily? Or are shadow passwords in NIS as secure as the good old shadow files?

  Read the article

• Getting Server 2008 R2 to ignore all traffic from Internet-facing NIC, leaving it to a VM

  - by Wolvenmoon

  I got in to Server 2008 R2 via Dreamspark and would like to start learning on it. I don't have much option but to put it on a system sitting between the Internet and my home LAN due to electricity bills and the fact that 3 computers in an 11x11 space in 102 degree weather is pretty stygian. Currently I use a ClearOS gateway to manage everything, what I'd like to do is take my server 2008 R2 box, which has two NICs, and drop it at the head of my network. I'd want Server 2008 R2 to ignore all traffic on the external facing NIC and pass it to a virtual ClearOS gateway, and to put all its Internet traffic through its other NIC - which will face the rest of my network and be the default gateway for it. The theory is to keep the potentially vulnerable Server 2008 R2 install as tucked behind a Linux box as possible, without sacrificing too much performance. This is a home network that occasionally hosts dedicated game servers and voice chat servers, so most malicious activity is in the form of drive by non-targeted attacks, however, I don't trust Windows Server because I don't know the OS well enough, yet. So, three questions: How do I do this, am I going to be reasonably more secure doing this than if I just let the Server 2008 R2 rig handle all the network traffic and DHCP (not an option), and should I virtualize the Server 2008 R2 rig instead and if so in what? (Core 2 Duo e6600 w/ 5 gigs usable RAM)

  Read the article

• Choosing the right TV tuner - USB or PCI TV tuners, hardware/software, DVB? Hybrid/combo/analog?

  - by Nucleon

  Greetings, I'll start with some background information so you know what I'm trying to accomplish and then get to my question. I work at a Television station in the US and we are working on setting up an online DVR/Podcast system for all of our newscasts. So basically we would be recording every newscast in HD, encoding it to flv/h.264 for viewing in a browser on flash compatible and iphone/ipad devices, eventually migrating to WebM when it's browser compliant. This task is theoretically pretty simple as it all it involves is a TV tuner device and a program like VLC, MythTV or whatever to schedule and dump it to a file, encode it with VLC/FFMPEG and push it to the streaming server. Now to the hardware, in order to accomplish that task, should I use an internal PCI tuner or a USB 2.0 tuner? Is there a difference? The bus speeds of both are not too far apart, and is the bus speed really relevant in this case? Does it matter if the device has a hardware encoder or a software encoder? On many sites the USB was recommended for ease of set up and use, but would it overly task a processor, or is that not a concern as long as it's a decent PC (at least duo core, 6gb ram). What's the difference between the stick USB and the Box USBs? To my understanding analog is basically gone in the US, so we would want a hybrid or combo tuner correct? How do those differ from DVB? Are there any other features or concepts which I am missing which may influence the recommended product. It would be ideal if the device which could work in both Linux and a Windows environment, to my knowledge most Hauppauge are? Example 1: PCI Hauppage http://www.newegg.com/Product/Product.aspx?Item=N82E16815116033 Example 2: USB 2.0 Box http://www.newegg.com/Product/Product.aspx?Item=N82E16815116029 Example 3: USB 2.0 Stick http://www.newegg.com/Product/Product.aspx?Item=N82E16815116031 Any guidance from the Superusers would be much appreciated!

  Read the article

• Apache2 on Raspbian: Multiviews is enabled but not working [closed]

  - by Christian L

  I recently moved webserver, from a ubuntuserver set up by my brother (I have sudo) to a rasbianserver set up by my self. On the other server multiviews worked out of the box, but on the raspbian it does not seem to work althoug it seems to be enabled out of the box there as well. What I am trying to do is to get it to find my.doma.in/mobile.php when I enter my.doma.in/mobile in the adress field. I am using the same available-site-file as I did before, the file looks as this: <VirtualHost *:80> ServerName my.doma.in ServerAdmin [email protected] DocumentRoot /home/christian/www/do <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /home/christian/www/do> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> From what I have read various places while googling this issue I found that the negotiation module had to be enabled so I tried to enable it. sudo a2enmod negotiation Giving me this result Module negotiation already enabled I have read through the /etc/apache2/apache2.conf and I did not find anything in particular that seemed to be helping me there, but please do ask if you think I should post it. Any ideas on how to solve this through getting Multiviews to work?

  Read the article

• Server appears to have lost ability to read PHP files with LAMP

  - by OtagoHarbour

  I have LAMP installed on a PC that is running Ubuntu 11.10. LAMP was running fine but I had to restart the PC because Unity was messing up (as it often does) and the tool bar had disappeared. When it started up, I was unable to fire up any php files. I have a file index.php in /var/www. It is owned by www-data as is the directory that it is in. The LAN address of the server is 192.168.1.10. However when I type 192.168.1.10 into the URL box on Mozilla FireFox, I get Unable to connect Firefox can't establish a connection to the server at 192.168.1.10 This server is connected to another server on the LAN that has the LAN address 192.168.1.4. When I type 192.168.1.4 into the Firefow URL box on 192.168.1.10, I see the display associated with index.php on 192.168.1.4. Why can it not display its own /var/www/index.php? Any assistance with this would be greatly appreciated, Peter.

  Read the article

• Exim and receiving email with large recipient lists

  - by AceJordin

  I have Exim4 running on Debian configured to receive mail on multiple domains. Exim is set to forward all email that is received to one of the domains to another box. This box is configured with a catchall mailbox that everything goes in. My issue is that when an email is sent to the domain, which contains a large amount of addresses (all to the same domain, but different users), Exim will receive the single email over multiple connections. This means that the catchall mailbox receives multiple copies of the single email all containing the full recipient list. For example, I was able to reproduce it by sending an email from my gmail account that contained 500 recipients (eg [email protected]; [email protected]; [email protected]; etc. for a total of 500). Exim received the message as 20 messages (25 recipients per; appears to be a gmail server setting). So the catchall mailbox received 20 messages, each containing all 500 addresses. I'm pretty sure I understand why this is happening but is there any way I can configure Exim to only receive it once, or to combine it into one? Is there anything that can be done on my end, or am I at the mercy of the sending email server? This is causing havoc with a process that polls the catchall mailbox and parses each recipient in each email.

  Read the article

• Skype Connect as SIP/Trunk for Asterisk

  - by Kaurin

  First off: I'm not sure if this should be on superuser or here. I have recently built a few Asterisk boxes with OpenVOX FXO/FXS ports little or no trouble. My current project is building an Asterisk box with SIP trunks. My current employer insisted on getting Skype Business/Skype connect for that purpose. After reviewing the Skype Connect plan, I agreed, because I thought it is going to be straightforward: Purchase G729 licences and setup SIP trunk/trunks. Boy was i wrong :) Here is the setup: The setup is for calling US numbers only via skype (we got skype US minute bundles in skype connect) AsteriskNOW - Asterisk 1.4 + asterisk-gui Trunks: SIP Trunk configured with Skype Connect - shows as registered Users: 2 test extensions. Both work fine when calling each other, voicemail etc works fine too The asterisk box is behind a Mikrotik router which i configured to forward all relevant ports: 5060-5090 UDP, 10000-20000 UDP. When trying out an extension outside of my LAN, it worked. I could make calls to the other extension. Outgoing rule: _NXXXXXXXXX Strip:0 Prepend:+1 Use skype trunk Inbound rule: Trunk: Skype Pattern: s Destination: Extension1 (6210) Here is the output of asterisk CLI (-rvvvvv) with outgoing calls: http://pastebin.com/eWVpL72e you can see the circuit-busy response when using trunk1 (skype) When calling my Skype Connect number from the outside, I get nothing in the logs. Can anyone with Skype Connect / Asterisk experience help out? :)

  Read the article

• LAMP server VM issues

  - by nullArray

  After getting a recommendation to salvage a wiki by installing a LAMP server, I went on the prowl for a good virtualized one. I used the VMware Player version. Since the windows box has Bonjour, I can, for example, go to http://lamp.local. and it works see the web client. The problem is, I can't ssh to a directory to scp the files I need, mount a usb thumbdrive (usbfs is unsupported) nor get samba working. I can't even update the ubuntu installation, it fails. I've tried bridged, nat and host-only networking settings in VMware Player. Bridged gives me an undefined IP, while the other two each have different IPs. All three settings allow me to access the web config, but none of them give me samba access. Windows usually freezes, then reports that it cannot connect. I'd rather not wipe a box to do a dedicated install, is there I way I can get this VM working, or are there better LAMP VMs out there? This one came already working and set up with VMware Player, so I thought it would be perfect... Thanks,

  Read the article

• How to set up IP forwarding on Nexenta (Solaris)?

  - by Gleb

  I am trying to set up IP forwarding on my Nexenta box: root@hdd:~# uname -a SunOS hdd 5.11 NexentaOS_134f i86pc i386 i86pc Solaris The box has 2 network interfaces: root@hdd:~# ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 e1000g1: flags=1001100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4,FIXEDMTU> mtu 1500 index 2 inet 192.168.12.2 netmask ffffff00 broadcast 192.168.12.255 ether 68:5:ca:9:51:b8 myri10ge0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 9000 index 3 inet 10.10.10.10 netmask ffffff00 broadcast 10.10.10.255 ether 0:60:dd:47:87:2 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 192.168.12.0 is my normal LAN with 192.168.12.1 being the firewall/gateway 10.10.10.0 is a separate LAN for iSCSI (with no internet access) I want to set up IP forwarding so that a computer on 10.10.10.0 will be able to access the internet by using 10.10.10.10 as a gateway (I don't need any port forwarding) I have turned on IP forwarding: root@hdd:~# routeadm Configuration Current Current Option Configuration System State --------------------------------------------------------------- IPv4 routing disabled disabled IPv6 routing disabled disabled IPv4 forwarding enabled enabled IPv6 forwarding disabled disabled Routing services "route:default ripng:default" Routing daemons: STATE FMRI disabled svc:/network/routing/rdisc:default disabled svc:/network/routing/route:default disabled svc:/network/routing/legacy-routing:ipv4 disabled svc:/network/routing/legacy-routing:ipv6 disabled svc:/network/routing/ripng:default online svc:/network/routing/ndp:default But when I dry to start ipnat, I get an error: root@hdd:~# ipnat -CF -f /etc/ipf/ipnat.conf ioctl(SIOCGNATS): I/O error Here is the config: root@hdd:~# cat /etc/ipf/ipnat.conf #!/sbin/ipnat -f - # map e1000g1 10.10.10.10/24 -> 192.168.12.2/32 So the question is how to fix this.. Thanks in advance!

  Read the article

• Vagrant up doesn't load chef configs and doesn't keep an error log

  - by la_f0ka

  I'm trying to set up a vagrant box and I'm running with all sort of troubles. Right now I'm getting a strange error message where it states there's a stack trace file with more info, but that file is no where to be found. This is the error: stdin: is not a tty [Sun, 16 Sep 2012 18:31:47 +0000] INFO: *** Chef 0.10.0 *** [Sun, 16 Sep 2012 18:31:48 +0000] INFO: Setting the run_list to ["recipe[apt]", "recipe[openssl]", "recipe[apache2]", "recipe[mysql]", "recipe[mysql::server]", "recipe[php]", "recipe[php::module_apc]", "recipe[php::module_curl]", "recipe[php::module_mysql]", "recipe[apache2::mod_php5]", "recipe[apache2::mod_rewrite]"] from JSON [Sun, 16 Sep 2012 18:31:48 +0000] INFO: Run List is [recipe[apt], recipe[openssl], recipe[apache2], recipe[mysql], recipe[mysql::server], recipe[php], recipe[php::module_apc], recipe[php::module_curl], recipe[php::module_mysql], recipe[apache2::mod_php5], recipe[apache2::mod_rewrite]] [Sun, 16 Sep 2012 18:31:48 +0000] INFO: Run List expands to [apt, openssl, apache2, mysql, mysql::server, php, php::module_apc, php::module_curl, php::module_mysql, apache2::mod_php5, apache2::mod_rewrite] [Sun, 16 Sep 2012 18:31:48 +0000] INFO: Starting Chef Run for natty.talifun.com [Sun, 16 Sep 2012 18:31:48 +0000] ERROR: Running exception handlers [Sun, 16 Sep 2012 18:31:48 +0000] ERROR: Exception handlers complete [Sun, 16 Sep 2012 18:31:48 +0000] FATAL: Stacktrace dumped to /tmp/vagrant-chef-1/chef-stacktrace.out [Sun, 16 Sep 2012 18:31:48 +0000] FATAL: NameError: wrong constant name Chef-symfony2Console Chef never successfully completed! Any errors should be visible in the output above. Please fix your recipes so that they properly complete. And this is what my vagrantfile looks like: Vagrant::Config.run do |config| config.vm.box = "ubuntu-1104-server-i386" config.vm.network :hostonly, "33.33.33.33" config.vm.forward_port 80, 8000 config.vm.share_folder "symfony.tests", "/var/www/symfony.tests", "data", :nfs => true config.vm.provision :chef_solo do |chef| chef.cookbooks_path = ["../my-recipes/cookbooks", "site-cookbooks"] chef.add_recipe "apt" chef.add_recipe "openssl" chef.add_recipe "apache2" chef.add_recipe "mysql" chef.add_recipe "mysql::server" chef.add_recipe "php" chef.add_recipe "php::module_apc" chef.add_recipe "php::module_curl" chef.add_recipe "php::module_mysql" chef.add_recipe "apache2::mod_php5" chef.add_recipe "apache2::mod_rewrite" chef.add_recipe "Symfony" chef.json = { :mysql => { :server_root_password => 'root', :bind_address => '127.0.0.1' } } end end

  Read the article

• How can a Postfix/Dovecot(ssl)/Apache/Roundcube(non-ssl) setup leak email addresses?

  - by Jens Björnhager

  I have a linux box email server with Postfix as the MTA, Dovecot as the IMAP server and Apache with Roundcube as webmail. In my /etc/postfix/aliases I have just above a hundred different aliases which makes as many email addresses on my domain. I use one address per website so I easily can shut down spam infested addresses. During the half a year or so that I have had this setup, I have received 3 spam from 2 sources. As I know exactly where I entered this address, it should be easy to pinpoint email leaking websites and services. However, these sources are, according to me, not likely email sellers. And for one of them to sell my email twice? I contacted one of the sources and they are adamant that their system is tight. They suggested the possibility that it is my server that is doing the leaking. So, my question is: How likely is it that my box is leaking email addresses, and how? I don't store fully qualified email addresses anywhere in my system except in my maildir. I use SSL connection to IMAP I do not use https on webmail

  Read the article

< Previous Page | 146 147 148 149 150 151 152 153 154 155 156 157  | Next Page >