Search Results

Search found 18594 results on 744 pages for 'computer science student'.

Page 151/744 | < Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >

• How to configure a large mtu (linux)

  - by Somejan

  I have a gigabit ethernet connection from my laptop to my router, and a working ipv6 connection to the internet. I can receive very large packets from sites on the internet, with sizes up to at least 10000 bytes (according to wireshark). (edit: turns out to be linux's 'generic receive offload') However, when trying to send anything, my local computer fragments at just below 1500 bytes for ipv6. (On ipv4, I can send tcp packets to the internet of at least 1514 bytes, I can ping with packets up to the configured mtu of 6128 but they are blackholed.) I'm on ubuntu 12.04. I have configured an mtu for my eth0 of 6128 (the maximum it accepts), both using ip link set dev eth0 mtu 6128 and in the NetworkManager applet gui, and restarted the connection. ip link show eth0 shows the 6128 mtu is indeed set. ip -6 route shows that none of the paths the kernel knows about have an mtu set. I can ping over ipv4 with packets up to 6128 bytes (though I don't get responses), but when I do ping6 myrouter -c3 -s1500 -Mdo I get error replies from my own computer saying that the packets are too large and the mtu is 1480. I have confirmed with Wireshark that nothing is put on the wire, and the replies are indeed generated by my own computer. So, how do I get my computer to use the larger mtu?

  Read the article

• How can I remove all drivers and other files related to a USB Mass Storage device?

  - by Bob

  I have a flash drive here that does not work on one OS on computer - let's call it the desktop Windows 7. It works fine on another computer - laptop Windows 7. It also works fine on Windows 8 on the same desktop computer. Other flash drives work fine under desktop Windows 7. So not a hardware issue, not a generic USB Mass Storage driver issue. It's something specific to this drive. On desktop Windows 7, I can connect the drive but no volume comes up under Windows Explorer. Ditto for Disk Management. With diskpart, loading hangs until I unplug the drive, if I replug it and try list disk it hangs again. If I unplug the drive at this point, list disk prints out all attached drives - including the just removed flash drive. The drive consistently appears under Device Manager, but uninstalling the drivers, restarting and reinstalling the drivers (by inserting the drive) only works for the first insertion. After that it fails again. I get the feeling that the driver files are not actually removed, and are corrupted, meaning every reinstall it's the same corrupted drivers being installed. Is there any way to remove these drivers completely? Or perhaps some other setting Windows 7 retains? Formatting the drive through another computer/OS does not help. I've also tried a complete wipe and rebuild of the MBR and single partition. The allocation unit size makes no difference; neither does a NTFS format. This is a relatively small matter, and I would not like to reinstall the entire OS!

  Read the article

• How can I use my cell phone to establish a dial-up networking connection?

  - by gWiz

  I am using Windows 7 and have a BlackBerry with T-Mobile (U.S.). I have paired the phone with my computer over Bluetooth, which automatically creates a serial port for it. I am able to open the port in PuTTY and successfully issue AT commands to the modem, including dialing. However, while using Windows to create and establish a Dial-Up Networking connection, I get an error dialog stating "Error 678. The remote computer did not respond." In my testing, I also tried setting up a connection to dial a number connected to a phone. When attempting to connect over this connection, the phone does ring but the very moment I answer the call, my computer displays the above error dialog. What must be done to successfully establish such a PPP connection? Some special AT initialization string perhaps? To clarify, I'm not referring to the well-described and popular technique known as "tethering," in which the remote host of the data link is the mobile service provider. I am interested specifically in establishing direct data links with remote hosts other than my mobile service provider. Think old-school landline connection to your friend's computer or BBS. Edit 1 As grawity pointed out in comments, the missing piece of the puzzle is the actual modulator that is compatible with v-series protocols, which I expected to be built into the cellphone. So far the best only software alternative I could find is this experimental project. Edit 2 Found this forum discussion today. The participants state that there is no old-school modem in the BlackBerry. Edit 3 When I place a call in PuTTY with ATD, immediately after the call is answered (and the callee is initiating the handshake) the cellphone returns OK. This is not the expected behavior for establishing a data connection. The phone should reciprocate the handshake, and upon success return CONNECT. (Alternatively it should return BUSY or NO CARRIER, but never simply OK.) Windows DUN must be interpreting this as the "Error 678" I was seeing.

  Read the article

• script to list user's mapped drive not giving results or error

  - by user223631

  We are in the process of migrating two file servers to a new server. We have mapped drives via user group in group policy. Many users have manually mapped drives and we need to find these mappings. I have created a PowerShell script to run that remotely get the drive mappings. It works on most computers but there are many that are not returning results and I am not getting any error messages. Each workstation on the list creates a text file and the ones that are not returning results have no text in the files. I can ping these machines. If the machine is not turned on, it does come up error message that the RPC server is not available. My domain user account is in a group that is in the local admin account. I have no idea why some are not working. Here is the script. # Load list into variable, which will become an array of strings If( !(Test-Path C:\Scripts)) { New-Item C:\Scripts -ItemType directory } If( !(Test-Path C:\Scripts\Computers)) { New-Item C:\Scripts\Computers -ItemType directory } If( !(Test-Path C:\Scripts\Workstations.txt)) { "No Workstations found. Please enter a list of Workstations under Workstation.txt"; Return} If( !(Test-Path C:\Scripts\KnownMaps.txt)) { "No Mapping to check against. Please enter a list of Known Mappings under KnownMaps.txt"; Return} $computerlist = Get-Content C:\Scripts\Workstations.txt # Loop through each item in the array (each computer in the list of computers we loaded into the variable) ForEach ($computer in $computerlist) { $diskObject = Get-WmiObject Win32_MappedLogicalDisk -computerName $computer | Select Name,ProviderName | Out-File C:\Tester\Computers\$computer.txt -width 200 } Select-String -Path C:\Tester\Computers\*.txt -Pattern cmsfiles | Out-File C:\Tester\Drivemaps-all.txt $strings = Get-Content C:\Tester\KnownMaps.txt Select-String -Path C:\Tester\Drivemaps-all.txt -Pattern $strings -notmatch -simplematch | Out-File C:\Tester\Drivemaps-nonmatch.txt -Width 200 Select-String -Path C:\Tester\Drivemaps-all.txt -Pattern $strings -simplematch | Out-File C:\Tester\Drivemaps-match.txt -Width 200

  Read the article

• I just got a virus 6 mins ago, how? Situation.

  - by acidzombie24

  -Edit- for the people who say it isn't a virus. Norton does detect it as a virus, an icon was placed on my system tray and rkpg.exe is in my C: which was placed 6 min ago around the time my computer rebooted on its own causing me to lose data :@. Situation I on Windows XP, behind a Linksys router, I don't have DMZ on so nothing should be connecting to me. I had Firefox, MSN and Visual Studio opened. With C# I programmed a quick application to scan some pages with Internet Explorer. The site it was scanning was deviantART (which is pretty trustworthy), I doubt any banners there would hold a virus. I went to a suspicious site called freetxt.com but that was on Firefox and it didn't load the site. With an extra check I ping it and got this message "Ping request could not find host freetxt.com." The virus seems to be called braviax. Right now it brought up a message saying my computer may be infected? How on earth did it get in? I don't have uTorrent installed or any torrent or p2p applications. Nothing is installed on my computer that I haven't installed before and I know the exact time it installed because I see rkpg.exe on my C drive and my computer restarted on its own around the same time. For the previous 30 minutes actually the previous hour all I did was talk on MSN, not click any links (I went to freetxt on my own) and had that Internet Explorer thing running (which I programmed). How did it get in? I really doubt it came from a banner on deviantART and installed when I loaded the page with the webbrowser-control so something else may have happened? Is there any system defaults I should turn off? I have remote assistance off but even if it was on I shouldn't be infected due to the router not forwarding any ports?

  Read the article

• Windows Server 2003 IPSec Tunnel Connected, But Not Working (Possibly NAT/RRAS Related)

  - by Kevinoid

  Configuration I have setup a "raw" IPSec tunnel between a Windows Server 2003 (SBS) machine and a Netgear FVG318 according to the instructions in Microsoft KB816514. The configuration is as follows (using the same conventions as the article): NetA | SBS2003 | FVG318 | NetB 10.0.0.0/24 | 216.x.x.x | 69.y.y.y | 10.0.254.0/24 Both the Main Mode and Quick Mode Security Associations are successfully completed and appear in the IP Security Monitor. I am also able to ping the SBS2003 server on its private address from any computer on NetB. The Problem Any traffic sent from a computer on NetA to NetB, or from SBS2003 to NetB (excluding ICMP Ping responses), is sent out on the public network interface outside the IPSec tunnel (no encryption or header authentication, as if the tunnel were not there). Pings sent from a computer on NetB to a computer on NetA successfully reach computers on NetA, but the responses are silently discarded by SBS2003 (they do not go out in the clear and do not generate any encrypted traffic). Possible Solutions Incorrect Configuration I could have mistyped something, somewhere, or KB816514 could be incorrect in some way. I have tried very hard to eliminate the first option. Have re-created the configuration several times, tried tweaking and adjusting all the settings I could without success (most prevent the SA from being established). NAT/RRAS I have seen multiple posts elsewhere suggesting that this could be due to interaction between NAT and the IPSec filters. Possibly the NetA private addresses get rewritten to 216.x.x.x before being compared with the Quick Mode IPSec filters and don't get tunneled because of the mismatch. In fact, The Cable Guy article from June 2005 "TCP/IP Packet Processing Paths" suggests that this is the case, (see step 2 and 4 of the Transit Traffic path). If this is the case, is there a way to exclude NetA-NetB traffic from NAT? Any thoughts, ideas, suggestions, and/or comments are appreciated.

  Read the article

• How to safely move where itunes saves music/iphone apps/and meta data to another internal Drive?

  - by GingerLee

  In the past, when I have moved my itunes data from one computer to another, I usually just follow these steps: Copy the contents of two folders: %USERPROFILE%\Music\iTunes %USERPROFILE%\AppData\Roaming\Apple Computer 1) Install iTunes on the new computer, start it and close it (don't let it search for music). 2) Copy all the files in the above folders from old PC to new PC. 3) Start iTunes and authorize the new computer (and deauthorize old one). 4) Before syncing, update all iphone apps to current versions on both my iphone and in itunes. 5) The Sync. The above steps always work for me, and basically Itunes on my new PC works exactly as it did on the old PC. My Question: In the hopes of bybassing the above steps in the future, I would like to just have Itunes use another internal Drive that I use for file storage (e.g. D:/) as the path for the above two directory? Then if I move to new PC again, I could just setup itunes to use the correct path. Is that possible yet with minimal implications? If so how?

  Read the article

• pfsense 2.0 traffic priority - set full priority for single host

  - by Waxhead

  I have a network with several computers all on the same network and since I have very limited bandwidth I would like to prioritize traffic almost like a CPU scheduler prioritize processes. Example: Computer A: Used for webstuff: YouTube, downloads, news, emails etc. Computer B: Transferring files over HTTP Computer C: Transferring files over ftp, rsync whatever What I would like to do is to give A up to for example 90% of the available bandwidth IF A requires it. The leftovers (10%) is divided between B and C (5% each if both is busy) If A is not utilizing all bandwidth then of course B and C should share the full bandwidth (50% each as long as both are maxing out their bandwidth). All computers are on the same network (192.168.1.0 - 192.168.1-10 for example). Appreciate if anyone could shed some light on how I should set up my network to achieve this. To be honest I actually need a step by step guide on how I should set this up. Network setup: (ADSL modem configured in bridge mode (1500kbps/300kbps)) [ADSL modem (bridge)]<-[pfsense2.0]<-[switch]<-[Computer A,B,C...etc]

  Read the article

• Dosbox USB print Windows 8.1 64Bit

  - by eCronik

  Worked fine until I've upgraded to Windows 8.1 as well as made the mail programm working (had to get a windows live ID and have to type in a password now, when starting Windows). I did set the USB printer to lpt1 on the local Windows 8 computer and another XP computer via LAN to lpt2 the same way with the same printer on the Windows 8 computer. But now it doesn't work anymore from the Win8 one (where the printer is plugged via USB). Tried already deleting lpt2: on the XP one, as well as lpt1 on the Windows 8, resetted it. Not working... :-( I tried also net use lpt1: \server\printer password "\user:Ute Berger" /persistent:yes of course with the correct server and shared printer name as well as net use \server\printer "\user:Ute Berger" password /persistent:yes . This is the name displayed as a user now. But in C:\users it is named Benutzer1. Tried this one also. Nothing worked. What could be the problem here? What's strange is that when I type "net use lpt1:" on the XP, I get another error (67 - The networkname wasn't found) than trying something I didn't set up like lpt2 (2 - The system can't find the file). Could this be a possible problem as even if deleted something is left blocking on the Windows 8 computer? Please help me - I tried for hours today but all I've got was frustration... Regards Tim

  Read the article

• Why is my Toshiba Satellite L675D laptop not connecting to my HD TV using an HDMI cord?

  - by Akasha Eyre

  I'm having a problem connecting my Toshiba Satellite L675 laptop to my Samsung HD TV. I've done it before using an HDMI cord but now, for some odd reason, it's not connecting at all. My computer screen before would go completely black for a second & then come back & (with it being attached to the TV with the HDMI cord & it being on the proper channel) it would make a sound, come on & work beautifully. Now, I try hooking it up & it doesn't do anything. No black screen, no sound. The TV screen just says there's no connection & that I need to check out the power source. I'm still checking around, trying to find out if there's a virus in my computer (since my dad & I have the same computer & he can connect his to the TV with no problems), or if I deleted something that had to do with the connection. I've tried turning my computer off & letting it sit for a while, I've tried checking out other websites & have come up with nothing.

  Read the article

• Problem with connecting two different networks

  - by tanascius

  I have two networks: 192.168.13.0/24 (blue) and 192.168.15.0/24 (green). Computer A is connected to the 13-net, only. Computer B has two interfaces, one in each network. There is third computer that acts like a router and connects the 13-net to the 15-net (only in this direction). Now, I'd like to ping 192.168.15.100 from computer A to B. Unfortunately there is never a reply. But when I use a hub instead of a switch it works. In my opinion the ping packet travels through the switch to the router (which is the default route/gateway for A). The router sends the packet back to the switch to B. Probably B receives it on its 15-net interface but answers with it's 15th interface? Is this possible? The problem is, that B may have only a gateway 192.168.13.50 - but I am not really sure of it (B is a embedded system with limited configuration possibilities). Can anyone explain what happens here? Thank you!

  Read the article

• Why just splitting an Ethernet cable does not work?

  - by Sin Jeong-hun

  I thought the Ethernet is logically one-line communication bus (for argument's sake, I am excluding hubs). All machines attached in the bus hears the same signals and the machines themselves try to avoid collisions by randomly backing off. http://computer.howstuffworks.com/ethernet6.htm If so, why splitting one Ethernet line from my home router into two and connecting two computers would not work? Why do I have to add a switch to it? *What the Internet said would not work. [4 port home router] ------[one Ethernet cable]-----[simple splitter]======[two computers] *What the Internet said I should do [4 port home router] ------[one Ethernet cable]-----[switch]======[two computers] Is this because of the signal degradation (reduced electric current)? Thank you for all the answers! The reason why I did not just use the two ports of my home router is... The 4-port gigabit router is in my room and I had put a computer in another room (also my room, though). Since wired network is far more reliable and secure, I had bought a long Ethernet cable and and connected the computer to the router. Now I was thinking about adding another computer to that room. I could buy another long Ethernet cable, but then there will be two cables between the rooms. The one line already is a minor annoyance, so I thought if I could share the one line between the two computers in that room. A switch would work, but it requires power and is a little bit pricey. That is why I wondered why it would not work to simply split the physical Ethernet cable. Apparently I do not completely understand how Ethernet and a switch work. I just have some bit of knowledge I heard in my college class.

  Read the article

• How to recover Windows Password without reinstalling if you forgot Windows password?

  - by user38908

  Usually, we can recover Windows admin password in two traditional ways. The first is to change Windows password with another admin account; the second is to recover the previous password with the windows password reset disk that had been created before you forgot the password. Take Windows XP for example, 1 At the Windows XP login prompt when the password is entered incorrectly click the reset button in the login failed window. 2 Insert the password reset diskette into the computer and click Next. 3 If the correct diskette Windows XP will open a window prompting for the new password you wish to use. However, we offen ignore the important of security until we have been locked out of computer. Fortunately, there is still the last way that can unlock your computer without reinstalling - erase Windows password with Windows password reset CD, which can recover admin password for Windows 7/XP/Vista/NT/2000/2003.... Take Windows Password unlocker for example, followings are the steps to create the reset CD 1.Download Windows Password Unlocker from Password Unlocker Official site 2.Decompress the Windows password unlocker and note that there is an .ISO image file. Burn the image file onto an blank CD with the burner freely supported by Password Unlocker. 3.Insert the newly created CD into the locked computer and re-boot it from the CD drive. 4.After launched the CD, a window pop up with all your account names(if you have several accounts) select one of the accounts that you have forgotten its password to reset it. Just one press, this software can remove Windows password instantly.

  Read the article

• Can I install windows on an SSD and access data from my old windows HDD?

  - by nzifnab

  I purchased new computer components, switching my hardware from AMD and Radeon to Intel and Nvidia. I kept components from my old computer like the powersupply and two HDDs. Everything appeared to install correctly and the system booted into the BIOS just fine (after a brief snafu with the CPU fan). My goal was to use the two harddrives and just be able to turn on the computer and load up my old windows install with all the files, programs, and documents. I expected to have to call Microsoft to re-register the windows install for the new hardware (since I had to do that last time I upgraded w/ the same windows version). When the computer attempts to boot into windows it briefly flashes a bluescreen and then restarts. System recovery gives a message something like "BadDriver Failover" something something. I assume this is because it's trying to use amd drivers for an intel chipset (or something...?) and I've been as-yet unsuccessful in getting it to boot into my old windows partition. SO! I decided eff it, maybe I'll go visit my nearest Micro Center and buy a 200 GB SSD, install windows onto that, and then... be able to access just the contents of both of my other harddrives? I don't intend on running any of the programs but there were some saved files I would like to salvage from the 500 GB harddrive, The 1.5 TB harddrive only had files on it, no OS or applications so I'd also expect to still be able to access it. Is this possible? Can I install the SSD and only format/install windows onto it and still access the contents from my two transferred-over drives?

  Read the article

• Internet compression proxy for low speed broadband?

  - by user23150

  I live in a rural location, using high-latency wireless off a local ISP's tower. My speed tests vary day to day, but I can get around 1Mb up/down. The problem is, I work with large files, uploading and downloading (HD videos, development software, etc.). It can be painful to wait sometimes. Plus I do some side contract game development, and it can be very difficult to playtest with other developers (200ms ping is a good day for me). Now, obviously it's not going to be easy to solve the latency problem without different wireless hardware. But speedwise, I am wondering if I can use some kind of compression technology on a proxy. For instance, my work computer has full access to a 26Mb down, 10Mb up connection, that is totally unused at night and the weekends. If I could run some kind of compression technology on our server, and use it as a proxy to route to my home computer, I could stand to gain some major speed. I realize that by bogging down a system with compression, I could potentially lose whatever speed gain I had. But the proxy server is a quad core xeon, and the receiving computer is a pretty decent i7 computer, so that shouldn't be a concern. I found http://toonel.net/ but it seems more geared toward very slow narrowband users, like dial-up. Plus, I would prefer to just be able to point my browser to a proxy server, rather then install software on my client machine. EDIT I thought about my question a little more, and realize I am going to need to install software on my client in order to decompress, and possible compress (for uploading). That's not a huge deal.

  Read the article

• Lost user account for Windows Vista

  - by annelie

  Hello, I'm trying to help a friend who's lost her user account in Vista. I know there's supposed to be a way you can boot the computer from the vista installation disc and create an admin account you can later login with, but her installation disc is in Australia and her laptop in London. Is there any other way to get in? Or would it be better to try and access just the harddrive? She's mainly concerned with getting all her data off it. As for how she lost the account, I'll let her explain in her words. :) My computer basically got some virus and now is up sh*t creek. it told me i had this cryptic thingy majiggy was missing and then this fake virus told me i needed to scan my computer. SO i tried to do malware thing but it kept shutting my computer down. ANYWAY...now its it will only open up with 'launch startup repair' and has got rid of my settings for logging in and wants me to be 'other user' which i have no password or username for'...so basically im stuffed. This is Windows Vista by the way. Thanks, Annelie

  Read the article

• Incorrect Internal DNS Resolution

  - by user167016

  I'm having a DNS issue. Server 2008 R2. The first clue was that after being off the network for a month, I could no longer Remote Desktop into my workstation by name, it wouldn't find it. Both via VPN and internally. But if I connect using its IP, that works. Now I notice in the server's Share and Storage Management, in Manage Sessions, it's displaying the incorrect computer name for some users. So I try, for one example: Ping -a 192.168.16.81 Pinging BOBS_COMPUTER.ourdomain.local [192.168.16.81] with 32 bytes of data: - replies all successful Then I try Ping RICHARDS_COMPUTER Pinging RICHARDS_COMPUTER.ourdomain.local [192.168.16.81] with 32 bytes of data: -all replies successful In DHCP, .81 belongs to RICHARDS_COMPUTER I did try flushdns. Not sure if this is related, apologies if it's not, but when I try to connect, I also get prompted: "The identity of the remote computer cannot be verified. Do you want to connect anyway? The remote computer could not be authenticated due to problems with its security certificate. It may be unsafe to proceed.." It then lists the correct name as the name in the certificate from the remote computer, but claims that the certificate is not from a trusted authority. Any thoughts are most appreciated!

  Read the article

• Formatting a former RAID 0 drive through USB

  - by EXC

  I'll try to be as specific as possible here: I was using two Hitachi 2.5" 500 gb HDDs in my Gateway P-7805u laptop in a RAID 0 configuration. The array was causing the laptop to run extremely hot, however, so I removed them and deleted the RAID array through Intel Matrix HDD manager. I did a clean install of Windows 7 on the original 320 gb HDD that came with the laptop. I never did format the original RAID array HDDs before taking them out of the computer. Now, I am attempting to format the Hitachi 500 gb RAID array HDDs externally through a USB external enclosure. The external HDD drivers install on my clean install OS, but when I go into 'My Computer' there is no external drive available. I cannot format in CMD Prompt because my computer will not designate a drive letter to the external HDD. The drivers install and the HDD is recognized as a Hitachi external drive, but nothing seems to show up in my computer window. I need to know if there is a way to format these drives to NTFS externally.

  Read the article

• Is there any any merit to routinely restore a linux system, even if unnecessary?

  - by field_guy

  I do fieldwork with a number of computers running ubuntu performing critical tasks doing fieldwork. The computers are similarly configured with slight variations. Since we've had some configuration issues in the past, my boss is pressing for us to take an image of the installation on each computer, and restore each computer to that image before they are to go into the field. My preferred solution would be to write a common script that checks to ensure that the configuration of the system is correct and that the system is operational. If the computer has been verified, isn't restoring it to that configuration redundant? And are there any inherent problems with doing so? My reluctance stems from the fact that our software and configuration is subject to change in the field, but these changes must be made across all the computers. That means that when a change is made, all the restoration images have to be updated as well. The differences in the configuration of each of the computers live in /etc. In the event that restoration is required, I would prefer to keep a single image containing everything that is common to all machines, and have a snapshot of each computer's /etc directory to be used for restoring the state of that particular machine. What's the better approach?

  Read the article

• Java Spotlight Episode 150: James Gosling on Java

  - by Roger Brinkley

  Interview with James Gosling, father of Java and Java Champion, on the history of Java, his work at Liquid Robotics, Netbeans, the future of Java and what he sees as the next revolutionary trend in the computer industry. Right-click or Control-click to download this MP3 file. You can also subscribe to the Java Spotlight Podcast Feed to get the latest podcast automatically. If you use iTunes you can open iTunes and subscribe with this link: Java Spotlight Podcast in iTunes. Show Notes Feature Interview James Gosling received a BSc in Computer Science from the University of Calgary, Canada in 1977. He received a PhD in Computer Science from Carnegie-Mellon University in 1983. The title of his thesis was "The Algebraic Manipulation of Constraints". He spent many years as a VP & Fellow at Sun Microsystems. He has built satellite data acquisition systems, a multiprocessor version of Unix, several compilers, mail systems and window managers. He has also built a WYSIWYG text editor, a constraint based drawing editor and a text editor called `Emacs' for Unix systems. At Sun his early activity was as lead engineer of the NeWS window system. He did the original design of the Java programming language and implemented its original compiler and virtual machine. He has been a contributor to the Real-Time Specification for Java, and a researcher at Sun labs where his primary interest was software development tools.     He then was the Chief Technology Officer of Sun's Developer Products Group and the CTO of Sun's Client Software Group. He briefly worked for Oracle after the acquisition of Sun. After a year off, he spent some time at Google and is now the chief software architect at Liquid Robotics where he spends his time writing software for the Waveglider, an autonomous ocean-going robot.

  Read the article

• Mission 26 Captures Endeavour’s Last Trip in Stop Motion

  - by Jason Fitzpatrick

  On September 21, 2012 the Space Shuttle Endeavour was delivered to the Los Angeles International Airport and spent the next three days being slowly transported 12 miles to the California Science Center. One dedicated team of photographers captured the whole thing. Lead by Matthew Givot, the group followed the shuttle for three straight days, photographing it around the clock. The Endeavor started on Thursday night and went on until Sunday night, with very little sleep to no sleep. The only thing that kept us going was pure love of the art and adrenaline. One thing that stood out the most for me, while I was shooting, was the people of Los Angeles. It was so powerful to see the excitement on peoples faces and the pride of their home town. No matter how many times I would see the Shuttle it would never get old. This has been an amazing experience that I will never forget. My hope is that this film will show you the amount of dedicated people and teamwork that it took to get the Endeavour to its new home. Enjoy. The end result of their labor is the above video, a beautiful time-lapse video of Endeavour’s journey from the airport to its hanger at the California Science Center. Can Dust Actually Damage My Computer? What To Do If You Get a Virus on Your Computer Why Enabling “Do Not Track” Doesn’t Stop You From Being Tracked

  Read the article

• Programming concepts taken from the arts and humanities

  - by Joey Adams

  After reading Paul Graham's essay Hackers and Painters and Joel Spolsky's Advice for Computer Science College Students, I think I've finally gotten it through my thick skull that I should not be loath to work hard in academic courses that aren't "programming" or "computer science" courses. To quote the former: I've found that the best sources of ideas are not the other fields that have the word "computer" in their names, but the other fields inhabited by makers. Painting has been a much richer source of ideas than the theory of computation. — Paul Graham, "Hackers and Painters" There are certainly other, much stronger reasons to work hard in the "boring" classes. However, it'd also be neat to know that these classes may someday inspire me in programming. My question is: what are some specific examples where ideas from literature, art, humanities, philosophy, and other fields made their way into programming? In particular, ideas that weren't obviously applied the way they were meant to (like most math and domain-specific knowledge), but instead gave utterance or inspiration to a program's design and choice of names. Good examples: The term endian comes from Gulliver's Travels by Tom Swift (see here), where it refers to the trivial matter of which side people crack open their eggs. The terms journal and transaction refer to nearly identical concepts in both filesystem design and double-entry bookkeeping (financial accounting). mkfs.ext2 even says: Writing superblocks and filesystem accounting information: done Off-topic: Learning to write English well is important, as it enables a programmer to document and evangelize his/her software, as well as appear competent to other programmers online. Trigonometry is used in 2D and 3D games to implement rotation and direction aspects. Knowing finance will come in handy if you want to write an accounting package. Knowing XYZ will come in handy if you want to write an XYZ package. Arguably on-topic: The Monad class in Haskell is based on a concept by the same name from category theory. Actually, Monads in Haskell are monads in the category of Haskell types and functions. Whatever that means...

  Read the article

• Common mistakes which lead to corrupted invariants

  - by Dave B.

  My main source of income is web development and through this I have come to enjoy the wonders of programming as my knowledge of different languages has increased over the years through work and personal play. At some point I reached a decision that my college education was not enough and that I wanted to go back to school to get a university degree in either computer science or software engineering. I have tried a number of things in my life and it took me a while before I found something that I feel is a passion and this is it. There is one aspect of this area of study that I find throws me off though. I find the formal methods of proving program correctness a challenge. It is not that I have trouble writing code correctly, I can look at an algorithm and see how it is correct or flawed but I struggle sometimes to translate this into formal definitions. I have gotten perfect or near perfect marks on every programming assignment I have done at the college level but I recently got a swath of textbooks from a guy from univeristy of waterloo and found that I have had trouble when it comes to a few of the formalisms. Well at this point its really just one thing specifically, It would really help me if some of you could provide to me some good examples of common mistakes which lead to corrupted invariants, especially in loops. I have a few software engineering and computer science textbooks but they only show how things should be. I would like to know how things go wrong so that it is easier to recognize when it happens. Its almost embarrassing to broach this subject because formalisms are really basic foundations upon which matters of substance are built. I want to overcome this now so that it does not hinder me later.

  Read the article

• Oracle Big Data Learning Library - Click on LEARN BY PRODUCT to Open Page

  - by chberger

  Oracle Big Data Learning Library... Learn about Oracle Big Data, Data Science, Learning Analytics, Oracle NoSQL Database, and more! Oracle Big Data Essentials Attend this Oracle University Course! Using Oracle NoSQL Database Attend this Oracle University class! Oracle and Big Data on OTN See the latest resource on OTN. Search Welcome Get Started Learn by Role Learn by Product Latest Additions Additional Resources Oracle Big Data Appliance Oracle Big Data and Data Science Basics Meeting the Challenge of Big Data Oracle Big Data Tutorial Video Series Oracle MoviePlex - a Big Data End-to-End Series of Demonstrations Oracle Big Data Overview Oracle Big Data Essentials Data Mining Oracle NoSQL Database Tutorial Videos Oracle NoSQL Database Tutorial Series Oracle NoSQL Database Release 2 New Features Using Oracle NoSQL Database Exalytics Enterprise Manager 12c R3: Manage Exalytics Setting Up and Running Summary Advisor on an E s Oracle R Enterprise Oracle R Enterprise Tutorial Series Oracle Big Data Connectors Integrate All Your Data with Oracle Big Data Connectors Using Oracle Direct Connector for HDFS to Read the Data from HDSF Using Oracle R Connector for Hadoop to Analyze Data Oracle NoSQL Database Oracle NoSQL Database Tutorial Videos Oracle NoSQL Database Tutorial Series Oracle NoSQL Database Release 2 New Features  Using Oracle NoSQL Database eries Oracle Business Intelligence Enterprise Edition Oracle Business Intelligence Oracle BI 11g R1: Create Analyses and Dashboards - 4 day class Oracle BI Publisher 11g R1: Fundamentals - 3 day class Oracle BI 11g R1: Build Repositories - 5 day class

  Read the article

• Teaching high school kids ASP.NET programming

  - by dotneteer

  During the 2011 Microsoft MVP Global Summit, I have been talking to people about teaching kids ASP.NET programming. I want to work with volunteer organizations to provide kids volunteer opportunities while learning technical skills that can be applied elsewhere. The goal is to teach motivated kids enough skill to be productive with no more than 6 hours of instruction. Based on my prior teaching experience of college extension courses and involvement with high school math and science competitions, I think this is quite doable with classic ASP but a challenge with ASP.NET. I don’t want to use ASP because it does not provide a good path into the future. After some considerations, I think this is possible with ASP.NET and here are my thoughts: · Create a framework within ASP.NET for kids programming. · Use existing editor. No extra compiler and intelligence work needed. · Using a subset of C# like a scripting language. Teaches data type, expression, statements, if/for/while/switch blocks and functions. Use existing classes but no class creation and OOP. · Linear rendering model. No complicated life cycle. · Bare-metal html with some MVC style helpers for widget creation; ASP.NET control is optional. I want to teach kids to understand something and avoid black boxes as much as possible. · Use SQL for CRUD with a helper class. Again, I want to teach understanding rather than black boxes. · Provide a template to encourage clean separation of concern. · Provide a conversion utility to convert the code that uses template to ASP.NET MVC. This will allow kids with AP Computer Science knowledge to step up to ASP.NET MVC. Let me know if you have thoughts or can help.

  Read the article

< Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >