Search Results

Search found 14641 results on 586 pages for 'postal address'.

Page 151/586 | < Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >

• OS X won't see Windows 7 in network (and vice versa)

  - by meds

  I've enabled SMB sharing in OS X Lion and have added folders to share, it says 'Windows Sharing: On' with a green circle next to it (from the sharing window) and that to access the volume I will need to to go to \\192.168.0.17. It also says that the OS X should be visible as 'macbook' in the network. Both my WIndows 7 and OS X are connected to the same network, yet when I try to go to \\192.168.0.17 or from the Mac try to go to my Windows system (smb://192.168.0.6) the two OSs don't see each other. Any ideas why? Attempting to ping the Mac from Windows results in this output in the command prompt: Pinging 192.168.0.17 with 32 bytes of data: Reply from 192.168.0.6: Destination host unreachable. Request timed out. Request timed out. Request timed out. Ping statistics for 192.168.0.17: Packets: Sent = 4, Received = 1, Lost = 3 (75% loss), ipconfig in Windows is: Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::8918:efd1:b05c:890f%21 IPv4 Address. . . . . . . . . . . : 192.168.0.6 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.1 Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::98ab:63fc:3c07:d837%13 IPv4 Address. . . . . . . . . . . : 192.168.74.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : fe80::80ff:c575:7b50:3a10%14 IPv4 Address. . . . . . . . . . . : 192.168.21.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Tunnel adapter isatap.{2E97D0AE-9E18-4072-AC23-1979BA0DCB79}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{E260CE43-E9A7-4DE0-A88E-4EAFF68ACDDB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{A5130812-59CE-4DDF-9C35-9433BCED9831}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{134BCAE7-CFFF-4A98-8DA0-3708806AABEB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{8D9E3B8F-161C-4ACE-B211-3EDD694416B2}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : in OS X: lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280 stf0: flags=0<> mtu 1280 en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=2b<RXCSUM,TXCSUM,VLAN_HWTAGGING,TSO4> ether c8:2a:14:01:24:c1 media: autoselect (none) status: inactive en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether e0:f8:47:0c:fe:04 inet6 fe80::e2f8:47ff:fe0c:fe04%en1 prefixlen 64 scopeid 0x5 inet 192.168.0.17 netmask 0xffffff00 broadcast 192.168.0.255 media: autoselect status: active p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304 ether 02:f8:47:0c:fe:04 media: autoselect status: inactive fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078 lladdr 70:cd:60:ff:fe:d8:f1:32 media: autoselect <full-duplex> status: inactive

  Read the article

• DNS server not working?

  - by Behrooz A

  I just set up a DNS Server on my windows 7, called SimpleDNS I added a zone for example sag.com and defined www.sag.com and sag.com to 192.168.1.2 (my Network IP Address) . the problem is when I try to ping sag.com the SimpleDNS logs says that it answered the request with 192.168.1.2 , but the ping doesn't resolve anything . SimpleDNS logs: > 14:00:43 Request from 192.168.1.2 for A-record for www.sag.com > 14:00:43 Sending reply to 192.168.1.2 about A-record for > www.sag.com: 14:00:43 -> Answer: A-record for www.sag.com = > 192.168.1.2 14:00:43 -> Authority: NS-record for www.sag.com = mehr-pc nslookup : > C:\Users\Mehr\Desktop>nslookup www.sag.com DNS request timed out. > timeout was 2 seconds. Server: UnKnown Address: 192.168.1.1 > > DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. > *** Request to UnKnown timed-out the DNS server IP is 192.168.1.2 , and Access point address : 192.168.1.1 what should I do?

  Read the article

• Connecting to IPv6 hosts when mobile and on a Surface?

  - by Cerebrate

  Specifically, at my usual location, I have an IPv6 network which connects to the Internet via a static tunnel set up to Hurricane Electric's tunnel broker ( http://www.tunnelbroker.net/ ). This works essentially perfectly, allowing inbound and outbound connectivity. Now, however, I need to connect back to host(s) on that network over IPv6 from mobile tablet(s); meaning the conditions are such that there is no guarantee or even likelihood of native IPv6 support where it happens to be at any given time, and the IPv4 address of the tablet will change on a fairly regular basis. The native Teredo support, as configured by default, functions well enough to let me ping my target hosts, but appears to have neither the reliability nor the throughput to support anything else; I have been unable to make any actual connections (trying a number of TCP-based protocols) using it. I had considered setting up an independent tunnel for the tablet(s), and using scripts to update the client endpoint IP address when it changes, but since both (a) many of the locations will be behind NAT devices over which I have no control, and (b) the option over which I do have control is an AT&T Unite hotspot which does not offer protocol 41 forwarding or respond to ICMP on its public address, this approach does not seem viable. I am additionally constrained as the mobile tablet(s) in question are Surface RTs, and as such are incapable of running, for example, AICCU client software. What is my best option to pursue to obtain IPv6 connectivity in this scenario?

  Read the article

• Returning a 404 page when a folder is accessed from one domain, but allowing access from other domains and IP addresses

  - by okw

  Situation: I want to return a 404 page ("404.php") when a folder ("hidden") is accessed from the example.com domain. I want the same folder to be accessible from a subdomain ("hidden.example.com") or from a different domain ("hidden.com") which are both configured in a single VirtualHost entry. The server has multiple IP addresses that it listens on. Each IP address serves identical content from the example.com domain (sharing a VirtualHost entry.) I want the folder to be accessible from the IP address. The server is configured to use SSL/TLS/HTTPS. HTTPS is optional on example.com, but HTTPS is enforced in the .htaccess file for the hidden folder using a rewrite rule shown below. /www/hidden/.htaccess RewriteCond %{HTTPS} !=on RewriteRule .* https://%{SERVER_NAME}%{REQUEST_URI} [R,L] I know that {SERVER_ADDR} gives the server's IP address, but does it return the one that the client is requesting from? I'm also starting to think that something in the VirtualHosts file would be more appropriate. Any thoughts on this? What should be allowed: http://87.65.43.21/hidden/ https://87.65.43.21/hidden/ http://12.34.56.78/hidden/ https://12.34.56.78/hidden/ http://hidden.example.com/ https://hidden.example.com/ http://hidden.com/ https://hidden.com/ http://www.hidden.com/ https://www.hidden.com/ What should be 404-ed with 404.php http://example.com/hidden/ https://example.com/hidden/ http://www.example.com/hidden/ https://www.example.com/hidden/ http://example.com/hidden/hiddenfile.php https://example.com/hidden/hiddenfile.php etc. Thanks.

  Read the article

• DNS server not working?

  - by Behrooz A

  I just set up a DNS Server on my windows 7, called SimpleDNS I added a zone for example sag.com and defined www.sag.com and sag.com to 192.168.1.2 (my Network IP Address) . the problem is when I try to ping sag.com the SimpleDNS logs says that it answered the request with 192.168.1.2 , but the ping doesn't resolve anything . SimpleDNS logs: > 14:00:43 Request from 192.168.1.2 for A-record for www.sag.com > 14:00:43 Sending reply to 192.168.1.2 about A-record for > www.sag.com: 14:00:43 -> Answer: A-record for www.sag.com = > 192.168.1.2 14:00:43 -> Authority: NS-record for www.sag.com = mehr-pc nslookup : > C:\Users\Mehr\Desktop>nslookup www.sag.com DNS request timed out. > timeout was 2 seconds. Server: UnKnown Address: 192.168.1.1 > > DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. DNS request timed out. > timeout was 2 seconds. > *** Request to UnKnown timed-out the DNS server IP is 192.168.1.2 , and Access point address : 192.168.1.1 what should I do?

  Read the article

• Opening port 80 in router has no results

  - by Ricardo Pieper

  A friend of mine has a ADSL modem and I need to forward some ports. I have already forwarded the 1521 port (Oracle) and it's working fine. Now I need to forward the port 80. I already set up his IIS bindings to this port, and also forwarded the port like this video shows: https://www.youtube.com/watch?v=DLKD-fyexoo So I think I did everything correctly. The local IP address is also the same as the machine where the IIS server is running. I'm sorry, but I can't post images since i don't have 10 points :( Somehow I can't forward this port, yougetsignal.com keeps saying that the door is closed. When I try to open the port, the Control Panel says me that I have to access the control panel in the 8080 port, because the 80 port will be open. Ok, that's fine. But I'm still able to access it in the 80 port, and when I try to access it in the 8080 port, it doesn't work. I'm trying it with the TPLINK 8816, but I also tried to open it in the Opticom DsLink 279, and it didn't worked (using another machine), I got the exact same results. He has a dynamic IP address, but he is also using No-ip, so I can always access his Oracle database in a certain static address. The 1521 port is open. I also tried to disable the firewall in Windows, but that makes no sense to me, since the router doesn't really open the port 80. Clearly I'm missing something. I have never done it in my life, so I dont know how to proceed. Restarting the router was the first I did, no results. I'm accessing his laptop through TeamViewer, so I'm testing the port outside his local network. Edit: My ISP says that they allow to open ports, and the 1521 port is opened. What could I do to open the 80 port?

  Read the article

• Postfix relay gives error 450 while it should be 550

  - by dieter-be

  Hi, we use postfix to do relaying. We get several messages like the following in /var/log/mail (slightly edited) Apr 13 13:30:29 linserver postfix/smtpd[1064]: NOQUEUE: reject: RCPT from unknown[$ip]: 450 4.1.1 <[email protected]>: Recipient address rejected: undeliverable address: host domain.be [$ip] said: 550 <[email protected]>: Recipient address rejected: User unknown in virtual mailbox table (in reply to RCPT TO command); from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<BLUESTREAK.domain.local> Now, when the master mail servers gives a 550, claiming that the user does not exist, I want the relay to also give a 550 back. What happens now is that it seems to return a 450, causing clients to keep messages queued, keep trying and only notify users after a certain period has passed. According to what I could find, the soft_bounce could cause this. But we have not enabled this option (and by default it's off according to postfix docs) It might also have something to do with the *_reject_code postconf values. Especially since the log message complains the unknown ip. But as you can see in the postconf output below, smtpd_sender_restrictions and smtpd_client_restrictions are empty. So even if it would try to do any restrictions there, 550 is the "worst" error going on, so that's what I expect to be returned to the client. postconf: http://sprunge.us/JYgB Thanks, Dieter

  Read the article

• DD-WRT (WRT54G) and (THOMSON TG782) how to put them togather?

  - by FeRtoll

  Ok so let me explain, i bought WRT54G and successfully installed DD-WRT v24-sp1 (07/26/08) mini-special - build 9994. That's all ok no problems with it all normal functioning. And just to add (i don't need wireless, wireless is turned off always) What i want: ISP's router (TG782) from it's INTERNET port(out) cable "which was before in my pc" is connected to WRT54G's INTERNET port and then from WRT54G LAN port 1 to my pc. The problem: How do i connect and setup all? I have tried many times on many different ways but cant get it to work IF THE CABLE FROM TG782 IS CONNECTED TO WRT54G ON INTERNET PORT. If i connect the TG782 to Lan port 1 on WRT54G and my pc to lan port 2 then all works fine after i setup gateway and all. But i want to connect TG782 to Internet port of WRT54G because i need "Access Restrictions" and this only goes through WAN right? please correct me if i am wrong. What i have tried: This is how i have tried to setup all. The TG782 router ip is 192.168.1.1 And WRT54G ip is 192.168.1.30 so in WRT54G control panel i have setup like this: ----WAN Connection Type---- Connection Type: Automatic Configuration - DHCP STP: Disabled ----Router IP---- Local IP Address: 192.168.1.30 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 (the TG782) ----Network Address Server Settings (DHCP)---- DHCP Type: DHCP Server Start IP Address: 192.168.1.100 Maximum DHCP Users: 6 And this wont work i probably miss something more, if anyone can help i would be thankfull. Also i have to note that i have tried to set my network adapter on pc to use the gateway of WRT54G and ip 192.168.1.102 In short: i cant get it to work normal only as a switch! Thanks for any help! -------EDIT:------- Here is an image which maybe can help: http://img27.imageshack.us/img27/4227/allin1w.jpg

  Read the article

• grepping a substring from a grep result

  - by allentown

  Given a log file, I will usually do something like this: grep 'marker-1234' filter_log What is the difference in using '' or "" or nothing in the pattern? The above grep command will yield many thousands of lines; what I desire. Within those lines, There is usually one chunk of data I am after. Sometimes, I use awk to print out the fields I am after. In this case, the log format changes, I can't rely on position exclusively, not to mention, the actual logged data can push position forward. To make this understandable, lets say the log line contained an IP address, and that was all I was after, so I can later pipe it to sort and unique and get some tally counts. An example may be: 2010-04-08 some logged data, indetermineate chars - [marker-1234] (123.123.123.123) from: [email protected] to [email protected] [stat-xyz9876] The first grep command will give me many thousands of lines like the above, from there, I want to pipe it to something, probably sed, which can pull out a pattern within, and print only the pattern. For this example, using an the IP address would suffice. I tried. Is sed not able to understand [0-9]{1,3}. as a pattern? I had to [0-9][0-9][0-9]. which yielded strange results until the entire pattern created. This is not specific to an IP address, the pattern will change, but I can use that as a learning template. Thank you all.

  Read the article

• VMWare Guest Info - Wrong IP Returned

  - by Jon Bailey

  We're running a VDI environment with vSphere 4.0 and Oracle VDI 3.2.2 and are having a bit of a problem with users that connect to an IPSec VPN from within their VM. For some reason, once connected to the VPN, the VMWare API returns GuestInfo.ipAddress as the VPN IP rather than the primary IP of the only NIC on the system. The IP address shown in net[0].ipAddress is the correct address and is what vSphere client is reporting. Is there any way to get VMWare tools to report the net[0].ipAddress as GuestInfo.ipAddress? Below is sample output from the guestinfo.pl script. 172.16.1.2 is the example "bad" VPN address that our VDI software is seeing. VMXFLEX01 guestFamily: windowsGuest VMXFLEX01 guestFullName: Microsoft Windows XP Professional (32-bit) VMXFLEX01 guestId: winXPProGuest VMXFLEX01 guestState: running VMXFLEX01 hostName: VMXFLEX01 VMXFLEX01 ipAddress: 172.16.1.2 VMXFLEX01 toolsStatus: VMware Tools is running and the version is current. VMXFLEX01 toolsVersion: 8194 VMXFLEX01 Screen - Height: 600 VMXFLEX01 Screen - Width: 800 VMXFLEX01 Disk[0]: Capacity 42935926784 VMXFLEX01 Disk[0]: Path : C:\ VMXFLEX01 Disk[0]: freespace : 33272619008 VMXFLEX01 net[0] - connected : 1 VMXFLEX01 net[0] - deviceConfigId : 4000 VMXFLEX01 net[0] - macAddress : 00:50:56:95:1f:c9 VMXFLEX01 net[0] - network : VM Network VMXFLEX01 net[0] - ipAddress : 10.0.0.2

  Read the article

• APACHE - PHP - Bounce emails

  - by user1179459

  I want to improve our mail server lists by handling all the bounces we get in our websites. I have a website which has over 8000+ users and another website which as over 1500+ users, they are emailed various notifications every second, ie. job alerts, email alerts, I am using POP connections with EXIM on APACHE server, most scripts are based on PHP language generates email on the fly. Problems i have But some users has registered long time ago and now quite few has bounce email address Some users register with dummy emails like [email protected] which never existed but a valid email address, any chance of stopping this without asking them login to the email account and clicking links which dont work most times.. (too annoying to the end user) Server is sending unnecessary emails can be avoided if i know they dont exists ? Solutions i need to have Is there a way i can download the bounce email list somewhere (WHM/Cpanel), i know exim mail has it but its not readable (i need a file like CSV or something similar to scan them over and write a php script to delete the users from the database ?) I need to know if there is any function in the PHP that can check the existence of the email address on the fly ? so that i can set the email send function in the mailer class to check before it sends out. On the server will bouncing emails are going to eatup lots of server resources ? like memory/cpu on processing them ? or are they are minimal where we dont have to worry about this at all ? May be a opensoruce or linux software to capture them and view them in a report basis and cleaning them up ? I am not a linux expert or server admin but i do lot of PHP coding, so please be descriptive of the solutions specially if they are linux commands Thank you!

  Read the article

• arp requests are sent continuously and my linux machine disconnected to the world

  - by sees

  I have the following problem and really need your help I'm implementing a small server to receive request from client on port 18999(just sample) using TCP socket. When I tested my server by using a lot of requests from a tablet through a router, I got the ARP problem(?) My net work just like: TABLET <------- WIRELESS ROUTER <------- MY SERVER (LINUX) Problems: 1. Can not connect to my Linux any more ( telnet, ping v.v...unreachable) 2. I use serial cable to connect to my Linux machine and use Wiresharp (from Windows) to catch the send message from Linux. It says that Linux keeps sending out continuously every 3 seconds ARP messages like the following: xx:xx:99:77:ff:69 ff:ff:ff:ff:ff:ff ARP 60 Who has 192.168.10.2? Tell 192.168.10.3 In the above message: xx:xx:99:77:ff:69 my Linux MAC address 192.168.10.2 my Tablet address 192.168.10.3 my Linux IP address Can you help me figure out the problem? Or tell me the way to detect the problem and reset the network back to normal (maybe restart Linux but I want to detect problem and restart automatically) UPDATE: 1. The above network works normally if tablet sends messages to my LINUX in normal speed (but also down after 48 hours) 2. The router works again after I unplugged my Linux ethernet cable (RJ45) from router. 3. The wireless network still works ( I can browser the router page from tablet) 4. When I use: ifconfig down then ifconfig up , the Linux restarts (?????????)

  Read the article

• Multiple Internet connections, multiple networks and split access in Linux

  - by Swapneel Patnekar

  I am having trouble setting up multiple internet connections for split access in Linux. We have 3 internet connections from 3 different ISP's. We want to configure our Linux gateway machine such that our three internal networks 10.2.1.0/24, 192.168.20.0/24 & 192.168.2.0/24 use ISP1, ISP2 and ISP3 respectively in a split access manner. Outlined below is the layout/settings, Interfaces of the Linux Gateway connected to Routers: eth0: 10.1.1.2<---------->10.1.1.1(Internal Interface of ADSL Router)[ISP1] eth1: 192.168.15.2<------>192.168.15.1(Internal Interface of 3G Router)[ISP2] eth3: 192.168.1.2<------->192.168.1.1(Internal Interface of ADSL Router)[ISP3] Kindly note that none of the interfaces in the Linux gateway has a public static IP address. Routers of ISP1 and ISP2 get assigned a dynamic public IP address when connected to the Internet, router of ISP3 has been assigned a public static IP address. Interface of Linux gateway connected to a switch, eth4: 10.2.1.1(LAN Interface for ISP1) eth4:0 192.168.20.1(LAN interface for ISP2) eth4:1 192.168.2.1(LAN Interface for ISP3) eth4:0 & eth4:1 are virtual interfaces with eth4 being the interface connected physically. Based on http://linux-ip.net/html/adv-multi-internet.html I've set the following routes, ip route flush table 4 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table 4 $ROUTE done ip route add table 4 default via 192.168.15.1 ip rule add fwmark 4 table 4 ip route flush cache Additionally, using the following iptables rules to mark & route packets as per the guide mentioned above : http://pastebin.com/KzWHFGJA At this point, computers from 192.168.2.0/24 network are successfully able to reach the Internet through ISP3. 192.168.20.0/24 and 10.2.1.0/24 are unable to access the Internet through ISP1 and ISP2 respectively. Any inputs will be much appreciated !

  Read the article

• Fresh Proxmox VE 2.1 installation with defaults can't be reached or pinged

  - by Damainman

  I am using the lastest Proxmox VE 2.1. My server has two NICS with a uplink only connected into eth0. My Server is a co-located server utilizing public IPv4 IPs. It is not behind a firewall or any system which monitors traffic. Via IPKVM I did a fresh install of Proxmox, I put in the correct IP, Mask, Gateway, and DNS information. The install went perfectly fine with no errors. Upon completion and rebooting the system: I am unable to reach the web GUI via the browser, it just times out. I am unable to ping the server. I am unable to ping outside to the Internet from within the server. Tried pinging out to 4.2.2.2 and yahoo.com I tried rebooting the server and restarting the network service. IFCONFIG shows my IP information under vmbro0 which also has the same MAC address as the eth0 device. eth0 only displays a IPv6 Scope:Link address, which I did not setup myself. This is my first time installing proxmox, but after searching for a few hours it doesn't seem like anyone else is having the same issue as me from a fresh install with just the defaults. So far the only thing I did was install it. Also, I know the network cable is good and the IP is good because I was running a Xen XCP server with the same network settings prior to wiping it to install proxmox. Some additional information: for pveversion -v (Installed proxmox-ve_2.1-f9b0f63a-26.iso) pve-manager: 2.1-1 (pve-manager/2.1/f9b0f63a) running kernel: 2.6.32-11-pve proxmox-ve-2.6.32: 2.0-66 netstat -nr (note: .136 is my network, and .137 is my gateway) Destination - Gateway - Genmask xxx.xxx.xxx.136 - 0.0.0.0 - 255.255.255.248 0.0.0.0 - xxx.xxx.xxx.137 - 0.0.0.0 /etc/network/interfaces auto lo iface lo inet loopback auto vmbr0 iface vmbr0 inet static address xxx.xxx.xxx.138 netmask 255.255.255.248 gateway xxx.xxx.xxx.137 bridge_ports eth0 bridge_stp off bridge_fd 0

  Read the article

• debian VM refusing all traffic apart from http

  - by james lewis

  I've got a VM with a fresh install of Debian (wheezy) and I've installed node and mongo on it. The VM is using a bridged network connection so I was expecting to be able to point my host machines browser at the ip address of the Debian VM (port 1337 for my node example or port 28017 for my mongo status page) and see one of the two services (node or mongo). My requests are refused though. As far as I can tell Debian allows all traffic by default and you have to manually configure iptables to drop traffic. I've checked iptables and it says it's setup to allow anything through. It looks like this: root@devbox:/home/jlewis# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination As a test I setup nginx and I was able to get to the nginx landing page from my host no problems so obviously http traffic is allowed. I then set nginx up to forward all traffic upstream to mongo - no problems there, I was able to see the status page. I then did the same for my example node server and again, no problems. So http traffic is fine, but all other traffic is blocked. Anyone know why debian might be refusing all other traffic other than iptables being setup to drop it? EDIT - output from netstat -nltp: Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:28017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:51028 0.0.0.0:* LISTEN 1541/rpc.statd tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 2462/sshd tcp 0 0 127.0.0.1:1337 0.0.0.0:* LISTEN 2794/node tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 2274/exim4 tcp 0 0 127.0.0.1:27017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 1510/rpcbind tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 2189/nginx tcp6 0 0 :::22 :::* LISTEN 2462/sshd tcp6 0 0 :::45335 :::* LISTEN 1541/rpc.statd tcp6 0 0 ::1:25 :::* LISTEN 2274/exim4 tcp6 0 0 :::111 :::* LISTEN 1510/rpcbind

  Read the article

• How to run a website domain without redirecting if IP is already used for another website? [duplicate]

  - by SSpoke

  This question already has an answer here: Hosting multiple distinct folders for distinct domains 1 answer I bought a VPS Host that gave me only 1 IP Address which I used on my first domain name and it works without any problems. Now my second domain name I can't use the same ip address as it points to the first domain name. So I figured my only option was to use a GoDaddy hosted iframe redirection which redirects to a sub folder on my first domain which worked so far. Now I'm trying to load paypal from <?php headers() ?> and I get a permission error because of that iframe Refused to display 'https://www.paypal.com/cgi-bin/webscr?notify_url=&cmd=_cart&upload=1&business=removed&address_override=1' in a frame because it set 'X-Frame-Options' to 'SAMEORIGIN'. How do I avoid the Iframe solution for my second domain while not messing up my first domain? Somebody I forgot once told me it doesn't matter if you have 1 IP Address you could host multiple websites on it? how it that possible the DNS doesn't seem to work off ports afaik, yes I could host multiple websites on different folders but that's not what I call hosting a real website it has to be pointed by a domain name, so this iframe issue doesn't happen My server configuration is httpd (apache) that comes with CentOS 6 (Linux) operating system

  Read the article

• How do I resolve certificate errors on HP blade center

  - by Martin Hilton

  I'm trying to sort out the ssl certificate errors that we get when trying to manage our HP c7000 blade enclosures. To that end I have created a signing certificate and imported it into the browser. In Onboard Administrator I created a certificate signing request, which I signed with my CA and then uploaded the certificate. This worked perfectly, and I no longer get any SSL errors when connection to Onboard Administrator. The problem comes when trying to connect through Onboard Administrator to the iLo on the blades themselves. Done by clicking on the "Web Administration" link. Onboard Administrator links to the blade with it's IP address rather than host name. But the certificate signing request that iLo creates uses the host name. Even when this certificate is signed the browser still complains it is for the wrong domain. I either need to be able to get Onboard Administrator to connect to the blades using host name rather than IP address, or get a certificate signing request which contains the IP address as the CN rather than the host name. It doesn't particularly matter which. Does anybody know how to configure this?

  Read the article

• Apache: How to redirect OPTIONS request with .htaccess?

  - by Milan Babuškov

  I have Apache 2.2.4 server with a lot of messages like this in the access_log: ::1 - - [15/May/2010:19:55:01 +0200] "OPTIONS * HTTP/1.0" 400 543 ::1 - - [15/May/2010:20:22:17 +0200] "OPTIONS * HTTP/1.0" 400 543 ::1 - - [15/May/2010:20:24:58 +0200] "OPTIONS * HTTP/1.0" 400 543 ::1 - - [15/May/2010:20:25:55 +0200] "OPTIONS * HTTP/1.0" 400 543 ::1 - - [15/May/2010:20:27:14 +0200] "OPTIONS * HTTP/1.0" 400 543 These are the "internal dummy connections" as explained on this page: http://wiki.apache.org/httpd/InternalDummyConnection The page also hits my main problem: "In 2.2.6 and earlier, in certain configurations, these requests may hit a heavy-weight dynamic web page and cause unnecessary load on the server. You can avoid this by using mod_rewrite to respond with a redirect when accessed with that specific User-Agent or IP address." Well, obviously I cannot use UserAgent because I minimized the server signature, but I could use IP address. However, I don't have a clue what should the RewriteCond and RewriteRule look for IPv6 address ::1. The website where this runs is using CodeIgniter, so there is already the following .htaccess in place, I just need to add to it: RewriteEngine on RewriteCond %{REQUEST_URI} ^/system.* RewriteRule ^(.*)$ /index.php?/$1 [G] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ /index.php?/$1 [L] Any idea how to write this .htaccess rule?

  Read the article

• Understanding Exchange User Monitor (ExMon) Output

  - by SturdyErde

  I recently downloaded and ran ExMon while trying to troubleshoot Outlook connectivity problems due to high CPU usage on Exchange Server 2010 SP2 UR8. The tool provides a great set of data, but I have not yet figured out how to make great use of it. My first question is why the Exchange Server itself shows up as a high-use MAPI client in the ExMon data. Among the users' client versions I see build numbers listed for Outlook 2013, 2010, and yes, even 2007 clients. I also see build number 14.2.387.0, which represents Exchange Server 2010 SP2 Update Rollup 8 (+/- some other patch that makes it not quite match the UR8 number). There are many user rows that list only "::1" and/or the short hostname of my Exchange server in the 'Client IP Addresses' column. Some other columns include the end-user's actual IP address and the Exchange server's IP address. ExMon shows that it is actually Exchange Server that is utilizing the highest percentage of CPU that is used for MAPI calls. I had expected to see 1 IP address and version number for each user reported by ExMon. Instead, most records show multiple version #'s (Exchange ver and Outlook ver) and multiple IPs (Exchange IP and client IP). Can anyone explain the reason for this to me, please?

  Read the article

• windows clients cannot get dns resolution until you open and close ipv4 properties page

  - by GC78

  This strange problem has started recently. Some windows clients cannot seem to get dns resolution to the internet after boot, and sometimes again at some point in the day. Internal hosts are also slow to resolve. trying to ping an interal host by name will take a long time for the hostname to resolve to ip address and trying to ping a website by name will fail to resolve. If you go into the tcp/ip v4 properties and view but not change anything, ok/close out of that then the client starts working fine, hostnames will resolve quickly. I have seen this happen on both Vista and W7 clients. ipconfig /all at a client experiencing this problem shows everything in order. proper ip addr, gateway, dns server, dns suffix ect.. ipconfig /dnsflush will not fix them, neither will /release and /renew the clients get their ip address, mask and dns server info from either one of 2 OES dhcp servers that assign addresses in different scopes in the same subnet. the internal dns server is a different OES dns server the default gateway is not assigned by the OES server but is statically put in at the client (only for those who need to get to the Internet for their job) flat network topology What can I do to get to the bottom of this? It only happens to a few of the client machines and typically the same ones. It started happening when we made a change to one of the DHCP scopes in iManager. Strangly this problem only happens to clients that get an IP address from the scope that we didn't make any changes to.

  Read the article

• Unstable DNS with bind

  - by yasser abd

  we have a Centos machine called jupiter, on which I have installed bind9, On every other machine the DNS is set to be the IP address of jupiter (192.168.2.101), as you can see in the output of the following command in windows >ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : mypcs Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme 57xx Gigabit Controller Physical Address. . . . . . . . . : 00-1A-A0-AC-E4-CC DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::c16d:3ae4:5907:30c4%8(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.2.98(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Thursday, September 20, 2012 10:26:11 AM Lease Expires . . . . . . . . . . : Sunday, September 23, 2012 10:26:10 AM Default Gateway . . . . . . . . . : 192.168.2.1 DHCP Server . . . . . . . . . . . : 192.168.2.1 DHCPv6 IAID . . . . . . . . . . . : 201333408 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-16-3A-50-01-00-1A-A0-AC-E4-CC DNS Servers . . . . . . . . . . . : 192.168.2.101 192.168.2.1 192.168.2.1 NetBIOS over Tcpip. . . . . . . . : Enabled All machines can always nslookup one of the domain (mydomain.com) that is set in the jupiter's DNS server, you can see that in the output of nslookup on the same windows machine: >nslookup mydomain.com Server: UnKnown Address: 192.168.2.101 Name: mydomain.com Address: 192.168.2.100 The problem is, sometimes mydomain.com can not be pinged, here is the output of the ping on the same windows machine >ping mydomain.com Ping request could not find host mydomain.com. Please check the name and try again. This looks very random, and happens once in a while, so the machine can lookup the DNS records but can't ping it, nor can browse the website that is hosted on mydomain.com, which should resolve to 192.168.2.100 On a linux machine that has the same DNS settings, the output of dig command for mydomain is as follows: $ dig mydomain.com ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6_3.2 <<>> mydomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 36090 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 1, ADDITIONAL: 1 ;; QUESTION SECTION: ;mydomain.com. IN A ;; ANSWER SECTION: mydomain.com. 86400 IN A 192.168.2.100 ;; AUTHORITY SECTION: mydomain.com. 86400 IN NS jupiter. ;; ADDITIONAL SECTION: jupiter. 86400 IN A 192.168.2.101 ;; Query time: 1 msec ;; SERVER: 192.168.2.101#53(192.168.2.101) ;; WHEN: Thu Sep 20 16:32:14 2012 ;; MSG SIZE rcvd: 83 We've never had the same problem on MACs, they always resolve mydomain.com Here is how I have defined mydomain.com on Bind9's configs on Jupiter, notice that the name of the machine on 192.168.2.100 is venus, so I have this file: /var/named/named.venus: $TTL 1D @ IN SOA jupiter. admin.ourcompany.com. ( 2003052800 ; serial 86400 ; refresh 300 ; retry 604800 ; expire 3600 ; minimum ) @ IN NS jupiter. @ IN A 192.168.2.100 * IN A 192.168.2.100 /var/named/zones/named.venus.zone zone "mydomain.com" IN {type master;file "/var/named/named.venus";allow-update {none;};}; One thing to note is that I haven't defined reverse DNS lookups, only the forward DNS lookups are defined in Bind9 configs, not sure if that's relevant or not. So my question is, why is this being so unstable? what could be the cause?

  Read the article

• Long access time for static web page on virtual machine

  - by Karol

  My setup Windows 7 on workstation that I use at work (with domain) and home (no domain) Virtual machine (VMWare) that runs Arch Linux (I will call it just "Linux") with network interface in bridged mode. Linux serves web pages with Nginx. IP address of Linux machine is 192.168.0.16 and is added to C:\windows\system32\drivers\etc\hosts: 192.168.0.16 bridged bri IP address of Windows workstation is added to /etc/hosts: 192.168.0.10 workstation I can add more details to my setup description (I am not sure what is relevant). The question Often (but not always) it takes long time for a web browser (Firefox) to open static web page served by Linux. I am sure it is not a performance issue. To be more specific: it takes about ~20 seconds to resolve(?) the address http://bridged for a web browser. Additionally I have just installed samba service and noticed similar problem, so it is not specific to browser & http. Initial access for samba shares also takes long time.

  Read the article

• Two DHCP servers on the same network

  - by CesarGon

  We are setting up a routing link between the Windows Server 2008 networks of two different buildings in my organisation. Each network uses a different IP addressing scheme (one uses public addresses, the other one uses private), but the goal is having a single Windows Server domain across the gap between the buildings. The link is provided by a 100-Mbps point-to-point line. I have always understood that you should not have more than one DHCP server on a network. However, we are planning to put a domain controller on each building, and each domain controller will be a DNS server and a DHCP server as well. The intention is that a machine booting up in building A gets its IP address from the DHCP server closer to it, in building A, while a machine booting up in building B gets an address from the DHCP server in building B. Since the two buildings will be linked and the network will be only one, will this work? How can I avoid that a machine booting up in building A gets an address from the DHCP server in building B (or vice versa)? Thanks.

  Read the article

• Two DHCP servers on the same network

  - by CesarGon

  We are setting up a routing link between the Windows Server 2008 networks of two different buildings in my organisation. Each network uses a different IP addressing scheme (one uses public addresses, the other one uses private), but the goal is having a single Windows Server domain across the gap between the buildings. The link is provided by a 100-Mbps point-to-point line. I have always understood that you should not have more than one DHCP server on a network. However, we are planning to put a domain controller on each building, and each domain controller will be a DNS server and a DHCP server as well. The intention is that a machine booting up in building A gets its IP address from the DHCP server closer to it, in building A, while a machine booting up in building B gets an address from the DHCP server in building B. Since the two buildings will be linked and the network will be only one, will this work? How can I avoid that a machine booting up in building A gets an address from the DHCP server in building B (or vice versa)? Thanks.

  Read the article

• Simple options for port forwarding to a different port?

  - by Nick

  I have three network printers at our local office, all of which listen on port 9100. Non of them offer the option of changing the listening port. We have a single public static IP address, and access to our main network is through a Linksys WRT-54G. We need to be able to print to these printers from outside the office. The problem is, with the 54G, I can only forward a port to the SAME port on a particular IP address. What I really need though is a way to forward to an ip address and a DIFFERENT port. I need to do this: In port Destination 9100 192.168.1.1 : 9100 9101 192.168.1.2 : 9100 9102 192.168.1.3 : 9100 So I'm looking for options. I could setup an old computer with two network cards and IPtables I suppose, but that seems like a lot of overhead for something relatively simple. Is there a way a virtual machine (read: one network card) could do the advanced port forwarding? Where I forward all traffic to it, and it forwards it on to the right printer? Or what about those mini Linux distros that replace the WRT-54G's firmware? Do any of those support what I need "out of the box"? I have a spare WRT- could I make it an IP tables router? Recommendations for mini distros? Or is there an off-the-shelf product that does this (cheap/local preferred)? Any advice / options appreciated. Thanks!

  Read the article

< Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >