Search Results

Search found 8401 results on 337 pages for 'bad habits'.

Page 152/337 | < Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >

• How to Disable secondary drive from booting upon restart - Windows

  - by DevCompany

  I had a Windows 2003 Hard Drive on my server and it went bad so I installed a new clean hard drive and installed Windows 2008 R2 on the new clean drive. I moved the old 2003 drive to be used only for general storage on the same computer. It usually boots into Windows 2008 upon a restart, but just sometimes it starts trying to boot the old 2003 drive and causes boot issues(NTDLR Bootloader, and other errors), even though the order of boot preference is set to boot 2008, and NOT 2003. I need to know how to remove any old code that keeps this old drive as a bootable drive. I still want to use it as a secondary drive just dont want to have any boot code on it. hopefully my situation is clear for everyone to get a good response. Thank you...

  Read the article

• Un-balanced network speed although using fiberoptic cable line

  - by Hoàng Long

  I'm not sure this is a right place to ask this question, but there's a strange thing that I don't quite sure what the reason is. My company has hired a fiberoptic cable line for network use (Wifi and cable through a router). But the strange thing is that, whenever someone view YouTube or listen stream music, then network speed for all the others become extremely slow. The download speed for that person is about 4-5 MB/s (or more), but others suffer. I'm still a newbie about networking. But I know there should be a solution. Could anyone tell me a way to stop this bad behavior? It's not possible for asking people not viewing YouTube, since that's part of their jobs. Any insights about this problem would be very welcome.

  Read the article

• SEAGATE Barracuda 7200.11 HDD not running

  - by Dane411

  After a huge research, I'm stuck at the beggining of getting my HDD data back. Whats happening to me is that in the moment when I plug the power wire to my external 1TB SEAGATE Barracuda 7200.11 ST31000333AS HDD Fw LC15, it makes the sound like it's spinning to almost full speed and then shuts down and spins up again, and so on. It's well known that those HDDs have a bad firmware that someday randomly fails. There are like 2 main problems identified, BSY (busy) state, and LBA0 error. Last time I connected it to power nothing happened, it didnt try to start at all, is it that so called bricked state? I guess my HDDs error is the first one, but I dont really know if what I described is that BSY state or not, neither I know how to check it. How could I know it? Thank you so much!

  Read the article

• What is the right way to use Internet Sharing in OS X?

  - by Bob King

  For a while now I've been using the Wireless in my Mac Mini as a seperate WiFi access point because my main router doesn't quite cover my whole house. There is a dedicated CAT 5E line down to the Mini, which has a static IP address. I've turned Internet Sharing on, using Airport/WiFi but it seems my options for security are limited. Can I do WPA2? Also, it seems like my iPhone only connects 25% of the time, and the rest of the time it claims I've given a bad password. I've tried "Forget this network" repeatedly.

  Read the article

• IP camera's multicast/RTSP conflicting with 2.4GHz Wi-Fi?

  - by jayson

  Here at our business we have a Netgear R7000 running DD-WRT. I have been slowly adding IP cameras which I run using Blue Iris software. The last camera I bought (which is NOT a wireless camera), when I plug it into the network I start having really bad connection issues on the 2.4GHz Wi-Fi network. The 5GHz works fine, just the 2.4GHz all of the sudden has trouble connecting, as if it's conflicting. I've tried playing with the camera settings, different IP addresses, HTTP ports, etc, and discovered it to be a conflict with multicast. When multicast is checked, the Wi-Fi has issues but my video streams via Blue Iris. When unchecked, Wi-Fi works fine but the video won't stream through Blue Iris. The problem is there are no settings in the camera to change the RTSP port, which is set to 34567. Does anyone know something that could fix this issue? It all seems very strange to me but maybe someone has an idea?

  Read the article

• Server reboots every 4.5-5.5 minutes...

  - by Andy

  Hi, I've recently installed a server in colocation, and my server is rebooting every 4.5-5.5 minutes. Regardless of the OS I run, it reboots. I have all ECC memory in the server, so it should correct errors if there is a bad bit in the memory, right? It's weird because it always happens about 4.5-5.5 minutes after bootup. My motherboard is a Supermicro X8DTL-iF. I read on a blog that another person had the problem, and supermicro recommended to do a BIOS update. Is this the right course of action?

  Read the article

• Changing the passphrase of a private key in Windows

  - by janos

  I have a private key in Windows, created by puttygen.exe. I used default options to save it, the tool automatically gave it a .ppk extension, and it looks like this: PuTTY-User-Key-File-2: ssh-rsa Encryption: none Comment: rsa-key-20130627 Public-Lines: 4 AAAAB3NzaC1yc2EAAAABJQAAAIBnvvAhyMs4rdlQd4OdajDw4jIPi6vIjrWjt4l4 5C3wHOSxyQQdtSA8XT3K0rSBnNtZRJTb5mfix67qQe3pHCTMSNsYIaBi8xQJHZRa RxdY+1VtGnSlEma8KO2We9eDNCGiwrRTUzqvTiGCnzU0pF1MXxu3ObISJcpqv+sQ 1GB0cw== Private-Lines: 8 AAAA.......... Private-MAC: XXXXXXXXX Now I need to change the passphrase, and reading from the docs it seemed simple enough: puttygen.exe -P key.ppk But this pops up a window with this error: PuTTYgen Error: Couldn't load private key (unable to open file) I also tried to change the passphrase using ssh-keygen that comes with Git Bash: ssh-keygen.exe -p -f key.ppk It asks for my old passphrase, but then it gives me the error Bad passphrase. Which is not true, because I can add the key in pageant.exe, and I am not mistyping the passphrase... Anything else I can try to change or drop the passphrase?

  Read the article

• Tool that automatically keeps old versions of a file? Shadow Copy in Win7?

  - by Michael Stum

  When I'm working with a Graphics App, I press CTRL+S a lot to Quicksave. Sometimes, I just went too far and made a bad decision, sometimes to the point Undo wouldn't help either. I would love to retain old versions of a file. Normally, Source Control would be of use here, but that's a manual process (same as just making some copies). I wonder if there is an automatic way to do that? Everytime the file changes, keep a backup. I believe that in Windows Server, Shadow Copies can do that. When I check in my Windows 7 (Ultimate), I do see "Previous Versions" as a tab, but that seems to be part of the backup function which is once again manual. Is there a way to get that type of automatic versioning?

  Read the article

• Should I limit end-user gigabit ports to avoid saturating uplink/trunk connections?

  - by Joel Coel

  We have a campus with 16 buildings and older 850nm 1Gbps fiber links between the buildings, that all come to a core switch for our servers that also uses 1Gbps ports. We're finally starting to replace our aging 10/100 end-user switches, and much of what we're looking at are 1 Gbps units. My question is, since the trunk/uplink lines are still 1Gbps, if I were to install 1 Gbps switches for end users, should I limit the ports to 100Mbps until I can also upgrade the trunks to avoid allowing a bad-behaving host to saturate a trunk line (since we're a college, we have plenty of mis-behaving hosts) and thereby create a DoS situation for a building, or will TCP congestion control typically take care of that for me? What if we have a lot of UDP traffic (games, video chats, even a small amount of bittorrent)?

  Read the article

• MDADM RAID5 array showing as CLEAN FAULTY

  - by Dean Reilly

  A drive dropped out of my raid 5 array yesterday. It looks like the reason was due to a bad controller so I switched it out and attempted to re-add the drive but mdadm claimed it couldn't do it. So I zerod the superblock and just added the drive normally and left it to resync. When I came to check on the array this morning I was unable to mount it at all and it's now showing as CLEAN FAULTY with two drives missing. The two missing drives are listed as spare and faulty spare. Is there anything I can do in this situation or is the array gone?

  Read the article

• Big noise from Power Supply Unity Fa? Should I replace it immediately?

  - by EApubs

  Recently, I started to get a large noise from my PC when switched on. After some time, it disappears. I discovered that the issue is with the Power Supply Unit. Does this mean I have a failing PSU? Will it harm the PC if I didn't replace it immediately? Several years ago I bought a new computer casing which is very weird. Its small and compact. Normally, we have the PSU in the top. But in here, the PSU is on the bottom and right below the hard drive. Recently, two of my hard drives started to show problems. Read errors and bad sectors. Can it be the PSU and the design of the casing? Here's an image of the PSU and the hard drive :

  Read the article

• Creative software leftovers - ASIO error message

  - by Tony Patriarche

  I temporarily installed an old Creative Audigy 2 soundboard on my Vista x64 Home Premium computer. Bad idea! I uninstalled the board & all software visible on the control panel. Now, with one particular app. (Sibelius) I keep getting a start-up message "CTASIO Warning: Creative ASIO: there are no Creative audio products installed on the system that support ASIO". I offer this as a candidate for "Most useless message", but that's beside the point. I used a commercial registry cleaner (PC-Tools Registry Mechanic) and then edited the registry looking for "creative", "audigy" and "ASIO". After removing everything I could find, I still get the message. Any suggestions?

  Read the article

• Inexpensive degaussers or HDD shredders?

  - by Nicholas Knight

  I do a lot of work for a small cash-strapped business that has a lot of active hard drives, most are consumer-grade SATA of about five years of age, and predictably they are dying at an increasing rate, and a lot of the time they can't even be detected, let alone complete a zero-out cycle. Right now those drives are just being stored, but that can't continue forever. We've got a couple bad LTO tapes it'd be nice to deal with, too. There are very real security and legal issues that make dropping them off with someone who claims they'll be properly destroyed a gamble. I've looked around at degaussers and HDD shredders, and the ones that don't look like they come from some guy in his basement all seem to be $3000+, which is hard to swallow right now. Is there anything out there in the $500-1500 range that you would recommend? (Speed isn't a big issue, if it takes several minutes or even hours per drive, that's completely OK, we've only got 10 or so thus far.)

  Read the article

• Is it possible to combine two internet connections to increase performance?

  - by cornjuliox

  I've got a small home network, 3 PCs plus a laptop or two when the relatives come to visit, connected to a single cable internet connection. Now, as soon as everyone starts using the 'net the performance starts to suffer and if the load is heavy enough nobody can get anything done and everyone complains. At one point it was so bad that only one of us could use it at a time. I was researching possible solutions to this problem and I heard that internet cafes that utilize 2 internet connections, possibly from different providers, and have some sort of router that allows them to split the traffic between the both of them, with online games going through one and web traffic going through another. Is this possible? What is the technical term for it, and can/should it be applied to a home network setup or is there another solution to this problem?

  Read the article

• Cannot do sudo: "/etc/sudoers is mode 0740, should be 0440"

  - by dehmann

  I have a problem: I don't have a root password on my mac. I just have an Admin account, which can do stuff using sudo. Now, I wanted to add my normal user to the /etc/sudoers file as well. Since it did not let me write to that file (even writing using sudo), I did this: sudo chmod u+w /etc/sudoers That worked. But since then I can't do any sudo command anymore on my system. It complains that /etc/sudoers has the wrong mode: $ sudo touch /etc/sudoers sudo: /etc/sudoers is mode 0740, should be 0440 Segmentation fault It sounds like a bad joke, because now I can't even change the mode back to 0440: $ sudo chmod 0440 /etc/sudoers sudo: /etc/sudoers is mode 0740, should be 0440 Segmentation fault Is there any way to fix this situation? I need to get my sudo abilities back.

  Read the article

• How to rewrite to a virtual directory with a different application

  - by user42181

  Hi, I have a CMS application that manages multiple websites, today whenever i change the codebehind of one of these websites - i have to rebuild the dll for all websites, deploy it - this disconnects all current sessions and is really bad. The iis is configured to listen to all domain requests, if the request is to one of the websites' domain , the application rewrites it, or example, if someone requests for www.example.com, and example.com is configured in the application to be website 12, it is rewritten to www.example.com/websites/12/default.aspx. This is done for all websites. We want to seperate the dlls of the websites from each other, and from the main CMS, we have a virtual directory to each websites, but when trying to rewrite to it, we discover that IIS support this (we get an "Could not load type '_12._Default'". error). How can we perform this rewrite so it does rewrite to virtual directories, or if anyone has any other solution for the initial dll seperation problem. Thanks in advance

  Read the article

• How do I create certificates for both ends of an stunnel connection?

  - by unixman83

  Hi. I am using stunnel to authenticate RDP (Remote Desktop) and I need to verify that a client possesses the proper credentials. So people cannot brute force into the machine. I am also using a bad (outdated) version of RDP that has security vulnerabilities, so stunnel is a must. I will preshare the necessary .pem's between machines. What are the openssl commands I need to create the right .pem files on both the client and on the server? What files need to be shared?

  Read the article

• Real-Time chat translation on mac using either Skype, Adium or iChat

  - by Cawas

  If you're looking for MSN and / or Windows, just go here. I'm looking for Real-Time chat translation tools for Mac, and preferably using Adium, but it could be for Skype, iChat or maybe another option if it's really good. So far I could only easily find a plugin for Adium, simply called translator, that uses google, dicts and babelfish, but you have to type commands in and paste the words or sentences, and it's currently not even working on Snow Leopard. Even if it did, it's still not quite as automatic as we'd expect (or see in other platforms as indicated). So I'm just citing it as an example of a bad solution.

  Read the article

• Intermediate SSL Certificates on Azure Websites

  - by amhed

  I have successfully configured an Extended-Validation Certificate on an Azure Website following this article: http://www.windowsazure.com/en-us/documentation/articles/web-sites-configure-ssl-certificate/ The main (non-technical) stakeholder of the web application went through great lengths to validate that our site is secure. He went to this site to check the validity of our SSL: http://www.whynopadlock.com/ The site throw the following error: `SSL verification issue (Possibly mis-matched URL or bad intermediate cert.). Details: ERROR: no certificate subject alternative name matches`` The certificate is installed using IP Based SSL instead of SNI. This is done this way because some site visitors still use Internet Explorer 8 on Windows XP, which has no support for SNI and throws a security warning. Is my certificate correclty installed? I received three .CRT files from my SSL provider: PrimaryIntermediate.crt SecondaryIntermediate.crt EndCertificate.crt This is how I exported our certificate as a .PFX file to Azure: openssl pkcs12 -export -out myserver.pfx -inkey myserver.key -in myserver.crt

  Read the article

• Time machine folders won't restore recursively

  - by Brian Postow

  I have a Snow Leopard system with Time Machine. Every so often I need to look at an old folder, so I go in and try to restore it, usually to a different location. What I end up with is an empty folder of the appropriate name. none of the files, nothing. It doesn't give any error messages. The files ARE there, because I can see them, also, if I go in via the mount point, and trace down through the file system, I can do a filecopy of the folder, and everything turns out fine. However, that seems like a bad idea. so, I'd like to know why he "right" way doesn't work... I believe that it used to work. It's also possible that it only doesn't work for certain folders. I haven't tested extensively.

  Read the article

• Ubuntu hang, and cannot be soft-reset after resuming from stand by mode

  - by Phuong Nguyen

  I have downgrade my xorg drivers, so I can hibernate and stand by my ubuntu smoothly. However, in some case, there's a problem. My ubuntu get hang. When I tried to switch to console mode (Ctrl+Alt+F1), then I cannot login. The system always reply with an error whenever I tried to press a key. When I press Ctrl+Alt+Del to perform a softreset, here what's it said: [80141.320122] end_request: I/O error, dev sda, sector 193687181 init: control-alt-delete main process (5660) terminated with status 2. This error is not even recorded in syslog. I guess this should be a problem with my hard disk since it said something about a bad sector. Exactly, what kind of error is this?

  Read the article

• wait after call command minecraft

  - by smeagogol

  I'm trying to create a batch file for a friend because he has some problems on minecraft. He needs to launch minecraft 80 times without closing java error... I have 2 batches, one with a while, and an other one executing java command for launching minecraft. ::Launcher.bat title Script Minecraft set tour=10 set tour2=tour :boucle set /a tour=tour-1 call "D:\thepath\Minecraft2.bat" if %tour%==0 goto suite goto boucle :suite wait javaw.exe :boucle2 set /a tour2=tour2-1 taskkill /F /IM "javaw.exe" if %tour2%==0 goto fin goto boucle2 :fin echo Appuyez sur une touche pour quitter... pause >nul and the other one ::Minecraft2.bat @echo off java -Xmx2048m -Xms1024m -cp "D:\thepath\Minecraft.exe" net.minecraft.LauncherFrame My problem is that when it calls the second batch, it's waiting for closure of the window but we must leave them opened ! If someone has already encountered this problem, I'd be grateful. Thanks PS: If my english is bad, it's because I'm french ;)

  Read the article

• Need Help Debugging BSOD

  - by nmuntz

  For the last few days I've been getting a BSOD at least once a day. Apparently the crash has been caused by ntkrpamp.exe and searching on google has revealed that the issue seems to be related to bad RAM. I have run memtest and my RAM modules have no errors on them. I'm pretty sure the issue is related to drivers, but I can't figure out which one. I'm not an expert in interpreting the output of windbg so any pointers would be greatly appreciated. Here is my analysis with WinDbg. It was too long to paste it here. One strange thing i noticed is that my Windows XP is in Spanish (SP3) and ntkrpamp.exe copyright info seems to be in portuguese. Not sure if that could be an issue, perhaps i have the wrong ntkrpamp.exe... Thanks a lot in advance

  Read the article

• My BrowserHelperObject is detected by avg as a malware, what is going wrong.

  - by BHOdevelopper

  Hi i'm building a BrowserHelperObject in c++ for Internet Explorer 8. It is a friendly add-on that gives you fonctionalities in a sidebar. The thing is that when you download the add-on executable from the web, AVG (AntiVirusGuard) detects the executable file as a malware. I did a lot of research and i can't find a way to not being seen as a bad malware. I know that BrowserHelperObject are often seen as malware, but mine is just a good and friendly add-on. Does anyone as info on how antivirus detection works and what can i do to prevent being seen as a malware. What has to be done to the BHO to pass avg detection ? Thank you.

  Read the article

• ARR servers in the Load Balancing pool automatically go from unavailable to available

  - by Chris

  I have 3 IIS web servers in an ARR web farm. When we do rolling releases, we take one server offline as a backup server and move it into an "Unavailable State" I have noticed that with ARR, servers will not stay in this state...they come back online automatically hours or days later. Does anyone know how to remedy this situation? This is very bad as the server that is down is typically not running the correct version of our code. I need to keep a server unavailable until i tell it otherwise.

  Read the article

< Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >