Search Results

Search found 4903 results on 197 pages for 'mq series'.

Page 152/197 | < Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >

• What are the biggest, best CPUs that support Physical Address Extension?

  - by Giffyguy

  I'm looking for a CPU that will support PAE and fit into an LGA775 socket. This combination of technology is very much preferred for my current server hardware/software setup. My priorities in order of highest to lowest: PAE & LGA775 At least 1066Mhz FSB Largest CPU cache possible Multiple Cores if possible HyperThreading if possible Most other factors are of little-to-no consequence. I'm finding it very difficult to figure out what my options are. Intel doesn't have much useful information on PAE (since x64 is so dominant), and Wikipedia simply says that "PAE is provided by Intel Pentium Pro (and above) CPUs - including all later Pentium-series processors except the 400 MHz bus versions of the Pentium M." All of Intel's listed Pentium CPU's support Intel64, which makes me seriously doubt they will support PAE with a 32-bit OS. And Wikipedia's claim is so vague, I have no idea if they mean up-to-and-including the x64 Prescott CPUs. PAE is supposed to be an aspect of the x86 architecture, and I believe it is no longer supported in an x64 environment. Please correct me if I am wrong.

  Read the article

• bootmgr image is corrupt

  - by bacord

  I just replaced my HD with a SSD. I did a brand new install on the SSD and I received the following error after booting BOOTMGR image is corrupt. The system cannot boot. A little configuration for your knowledge. The system used to be a dual boot with XP & windows 7. After replacing the original startup HD with my SSD I changed a setting in the bios to AHCI (I have tested changing it back but this did not help). When I look at the stats on the drive in the bios, it claims that the SSD is in a raid configuration despite the settings not being configured that way. Related System Information: Intel 320 Series 80 GB Sata II SSD JetWay JPA78VM3-H-LF AM2+/AM2 AMD 780V HDMI Micro ATX AMD Motherboard AMD Athlon 64 X2 7 GB ram I have performed 2 fresh installs to no avail. Also, followed this guide and performed option 1 and 2. I have done bootsec/fixmbr and /fixboot. So.. any suggestions?

  Read the article

• Solaris 10: How to image a machine?

  - by nonot1

  I've got a Solaris 10 workstation that I'd like to create a full image backup from. The machine has 2 drives, one UFS for system root, and 1 ZFS for data storage. I intend to add a third HD to keep the backup images of both primary drives (including any zfs snapshots). The purpose is not disaster recovery, but rather to allow me to easily blow away a series of application installation/configuration changes I intend to try. What's the best way to do this? I'm not too familiar with Solaris, but have some basic Linux knowledge. I looked at CloneZilla, but it does not support Solaris. I'm OK with just a dd | gzip > image style solution, but I'd need some way to first zero-out the non-used blocks on the primary drives to aid gzip. They are are much larger than my 3rd drive, but hardly have any real data. Update to clarify: I specifically want to avoid using any file-system snapshot functionality, because part of the app configuration changes involve/depend slightly on existing and new snapshots. Ideally the full collection of snapshots should be part of the backup. Virtualization not an option, because the goal is to do performance evaluation on a very specific HW configuration. For the same reason, the spurious "back up" snapshots could skew performance data. Thank you

  Read the article

• How to create Windows Vista/Windows 7 Startup disk or Rescue disk or system restore points on a CD?

  - by goldenmean

  Hello, I have two laptops, one having Windows-Vista home premium and other one having Windows-7 professional. Both versions of OS are OEM installs(pre-installed when I bought the laptop) and I do not have the Windows Installation disks for them. usually the installation disks provide a repair option in case one needs to repair/rescue a improper windows installation. But since I dont have the installation disks, I want to create rescue disks/startup disks for these. My questions are : 1] How to create a system rescue disk/startup disk on a CD from these two versions of Windows? 2] Doesn't the system restore points which Vista/Windows-7 create, cannot be created on a CD disk instead of hard-disk? 3] If I have a manual backup of my windows registry, in which I have exported all the registry to a file and I have that file on a CD, how to restore that registry back to the windows installation which might not be booting up properly due to bad registry problem. EDIT: 4]Is there any way to use these system restore points directly during bootup of the laptop, if windows does cannot boot properly due to problem. First laptop is HP Pavillion dv6646 and second one is Sony VAIO VCPEE series. thank you. -AD

  Read the article

• Configuring https access on HP A5120 Switch

  - by GerryEgan

  I am trying to configure HTTPS management on a HP a5120 switch running Version 5.20.99, Release 2215 and not having much luck. I have followed the manual by creating an SSL policy first and then enabling the HTTPS server with the SSL policy: ssl server-policy sslpol ip https ssl-server-policy sslpol ip https enable When I try and log onto the switch with Google Chrome I get the following error: Error 107 (net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error. When I look this up I have found references to errors due to TLS being used in SSL. I can find no way to specify the SSL version in the server policy. The manual has a configuration example that uses MSCEP to retrieve a certificate but in Windows 2008 R2 that feature is only available in Enterprise and Datacentre editions which I don't have. I have SSH configured and it is using a locally generated certificate so I'm not sure if I can use that but I'd like to if possible. Has anybody been able to setup HTTPS management on HP A series switches without MSCEP? Any and all help appreciated! here is a copy of my config with the interfaces removed: version 5.20.99, Release 2215 # sysname MYSYSNAME # irf domain 10 irf mac-address persistent timer irf auto-update enable undo irf link-delay # domain default enable system # telnet server enable # vlan 1 # vlan 100 description Management # radius scheme system primary authentication 127.0.0.1 1645 primary accounting 127.0.0.1 1646 user-name-format without-domain # domain system access-limit disable state active idle-cut disable self-service-url disable # user-group system group-attribute allow-guest # local-user admin password cipher authorization-attribute level 3 service-type ssh telnet terminal service-type web # stp enable # ssl server-policy sslpol pki-domain MYDOMAIN # interface NULL0 # interface Vlan-interface199 ip address 192.168.199.140 255.255.255.0 # interface GigabitEthernet1/0/1 poe enable stp edged-port enable # interface Ten-GigabitEthernet2/1/2 # dhcp-snooping # ntp-service unicast-server 192.168.1.71 # ssh server enable # ip https ssl-server-policy sslpol ip https enable # load xml-configuration # user-interface aux 0 1 user-interface vty 0 15 authentication-mode scheme

  Read the article

• Multi-WAN bonding across different media

  - by Tom O'Connor

  I've recently been thinking again about a product that Viprinet provide, basically they've got a pair of routers, one that lives in a datacentre, Their VPN Multichannel Hub and the on-site hardware, their VPN multichannel routers They've also got a bunch of interface cards (like HWICs) for 3G, UMTS, Ethernet, ADSL and ISDN adapters. Their main spiel seems to be bonding across different media. It's something that I'd really like to use for a couple of projects, but their pricing is really quite extreme, the hub is about 1-2k, the routers are 2-6k, and the interface modules are 200-600 each. So, what I'd like to know is, is it possible with a couple of stock Cisco routers, 28xx or 18xx series, to do something similar, and basically connect a bunch of different WAN ports, but have it all presented neatly as one channel back to the internet, with seamless (or nearly) failover if one of the WAN interfaces should fail. Basically, If i got 3x 3G to ethernet modems, and each on a different network, I'd like to be able to loadbalance/bond across all of them, without having to pay Viprinet for the privilege. Does anyone know how I'd go about configuring something for myself, based around standard protocols (or vendor specific ones), but without actually having to buy the Viprinet hardware?

  Read the article

• New build won't boot: some fans turning, no beep or video

  - by Dave

  When my new system is powered up, the case fan and power supply fans turn fine. The CPU fan twitches, but never gets going. Although I've heard that with AMDs and Gigabyte motherboards that is not necessary a problem. Hard drive is spinning. However, there is absolutely no indication that anything else is happening. The motherboard, as far as I can tell, does not have an internal speaker, but I harvested one from another machine and plugged it in and still no beeps at all. The monitor screen stays black, on both the integrated VGA and DVI. This is a brand new build, and has never successfully booted. My parts are: AMD Athlon II X2 245 Regor 2.9GHz Socket AM3 65W Dual-Core Processor Model ADX245OCGQBOX - includes CPU cooler) GIGABYTE GA-MA785GPMT-UD2H AM3 AMD 785G HDMI Micro ATX AMD Motherboard - Retail G.SKILL Ripjaws Series 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666) Desktop Memory Model F3-10666CL8D-4GBRM - Retail CORSAIR CMPSU-400CX 400W ATX12V V2.2 80 PLUS Certified Compatible with Core i7 Power Supply - Retail SAMSUNG Spinpoint F3 HD502HJ 500GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive COOLER MASTER Elite 341 RC-341C-KKN1-GP Black Steel MicroATX Mid Tower Computer Case - Retail I also have a DVD burner, but it acts the same whether that is plugged in or not. I'm using the on board video. What I've tried so far: I've switched power supplies, with no difference. I've tried different monitors (of which all are working on other machines) with no difference. I have tried putting it one memory module at a time, with no difference. I have tried the absolute minimum I can think of (power supply into motherboard, power button ONLY plugged into front panel, CPU fan plugged in), with no difference. I appreciate any ideas anyone might have. Do I need to RMA the motherboard? This is my first build, so there might be something obvious. I was very careful in assembly with static; I'm confident nothing was zapped during assembly.

  Read the article

• Installing Numpy locally

  - by Néstor

  I posted this question originally on StackOverflow, but a user suggested I moved it here so here I go! I have an account in a remote computer without root permissions and I needed to install a local version of Python (the remote computer has a version of Python that is incompatible with some codes I have), Numpy and Scipy there. I've been trying to install numpy locally since yesterday, with no success. I successfully installed a local version of Python (2.7.3) in /home/myusername/.local/, so I access to this version of Python by doing /home/myusername/.local/bin/python. I tried two ways of installing Numpy: I downloaded the lastest stable version of Numpy from the official webpage, unpacked it, got into the unpacked folder and did: /home/myusername/.local/bin/python setup.py install --prefix=/home/myusername/.local. However, I get the following error, which is followed by a series of other errors (deriving from this one): gcc -pthread -shared build/temp.linux-x86_64-2.7/numpy/core/blasdot/_dotblas.o -L/usr/local/lib -Lbuild/temp.linux-x86_64-2.7 -lptf77blas -lptcblas -latlas -o build/lib.linux-x86_64-2.7/numpy/core/_dotblas.so /usr/bin/ld: /usr/local/lib/libptcblas.a(cblas_dptgemm.o): relocation R_X86_64_32 against `a local symbol' can not be used when making a shared object; recompile with -fPIC Not really knowing what this meant (except that the error apparently has to do with the LAPACK library), I just did the same command as above, but now putting LDFLAGS='-fPIC', as suggested by the error i.e., I did LDFLAGS="-fPIC" /home/myusername/.local/bin/python setup.py install --prefix=/home/myusername/.local. However, I got the same error (except that the prefix -fPIC was addeded after the gcc command above). I tried installing it using pip, i.e., doing /home/myusername/.local/bin/pip install numpy /after successfully instaling pip in my local path). However, I get the exact same error. I searched on the web, but none of the errors seemed to be similar to mine. My first guess is that this has to do with some piece of code that needs root permissions to be executed, or maybe with some problem with the version of the LAPACK libraries or with gcc (gcc version 4.1.2 is installed on the remote computer). Help, anyone?

  Read the article

• Windows 7 Won't Boot

  - by Vie

  I recently built a new computer, my fifth one. ASUS Maximus III Formula LGA 1156 Intel P55 ATX Motherboard EVGA 01G-P3-1452-TR GeForce GTS 450 Superclocked 1GB 128-bit GDDR5 PCI Express 2.0 x16 HDCP Video Card COOLMAX RM-1000B 1000W ATX psu Intel Core i7-875K lynnfield 2.93GHz LGA 1156 95w Quad-Core unlocked processor G.SKILL Ripjaws Series 16 (4x4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666) memory WD VelociRaptor WD3000GLFS 300gb 10000 RPM SATA 3.0Gb/s Hard Drive Sony Optiarc CD/DVD Burner model AD-7261S-0B LightScribe Windows 7 Home Premium 64-bit It gets hung up on the starting windows screen. When I went to install the OS it did the same thing wouldn't go past the windows logo, so I put the new HDD into my old computer and installed windows 7 thinking it was just an installer error. Put the fully installed HDD back into my new machine and it still gets stuck on the starting windows screen. I've tried most everything I've looked up. Disabled USB, Disabled Turbo Boost, Disabled everything that wasn't essential(just about every configuration I can think of), took it apart and put it back together, took all the ram out save one 4g stick(wouldn't even boot when I did this), did a memory scan which came back successful, I don't know what could be wrong. Only thing I can think of is a compatibility issue somewhere, but I've ran over it again and again and I don't know where there would be an issue like that. Need Backup! .<

  Read the article

• Looking for comprehensive computer monitoring software

  - by cornjuliox

  Summer in this country is insanely hot. So hot in fact, that I think we just lost a machine due to overheating (last recorded CPU/GPU temp was close to 100 C, now it wont start and lets out a long series of short beeps on power up), but that's not my concern here. Since heat is such a problem for me, I use several different pieces of software to monitor temperatures in my machine. I use MSI Afterburner to monitor GPU temp, control GPU fan speed and for some light overclocking, and then I use Speccy and SpeedFan to monitor the rest of the system, CPU temp and everything. The setup works fine for now, but I want to consolidate all this into one program so I'm not juggling several windows at once. Is there any program out there that will let me monitor the following from a single window: CPU Temp and Fan Speed CPU clock GPU Temp and Fan Speed GPU clock, both core and memory Additionally, mobo temp (Speccy lists both CPU and Motherboard temp, I assume that the latter is referring to North and Southbridge temperatures. I'm also looking for the ability to chart these data points on a graph over time, basically to see just how high the temperatures spike under load and for general analysis. It'd be nice if it could handle overclocking of both CPU and GPU in real time too. Any suggestions? Edit: I forgot to mention that I'm on Windows 7, 64-bit

  Read the article

• (manually configured) kernel update leaves wireless in a mess

  - by Mala

  I recently upgraded my kernel from 2.6.31-gentoo-r6 to 2.6.32-gentoo-r7. In both cases, I configured everything manually. However, since the upgrade, my wireless card appears to be on the fritz. It will connect to networks just fine, and remain connected, but can only access the internet (and other hosts on the network) for about 3 seconds after connecting. Reconnecting to the network appears to fix the problem... for another 3 seconds or so. The problem is "solved" by booting into the older kernel. The relevant lspci entry is 02:00.0 Network controller: Intel Corporation PRO/Wireless 5300 AGN [Shiloh] Network Connection I'm pretty sure I have the correct drivers enabled in the kernel Device Drivers ---> Network device support ---> Wireless LAN (IEEE 802.11) ---> <*> Intel Wireless Wifi [*] Enable LED support in iwlagn and iwl3945 drivers [*] Enable Spectrum Measurement in iwlagn driver [*] Enable full debugging output in iwlagn and iwl3945 drivers <*> Intel Wireless WiFi Next Gen AGN (iwlagn) [*] Intel Wireless WiFi 4965AGN [*] Intel Wireless WiFi 5000AGN; Intel WiFi Link 1000, 6000, and 6050 Series I tried with the other intel drivers enabled as well (iwl3945) and no difference. Is there something stupid I'm missing? Is there something I have to recompile after upgrading the kernel (a la nvidia)? Thanks Mala

  Read the article

• New SSD, is the MBR broken? DISK BOOT FAILURE

  - by Shevek

  I've been running Windows 7 on a WD 500gb SATA single drive, single partition setup for some time with no issues. I've just installed a new Kingston V Series 64gb SSD and performed a clean install of Win7 to it, deleting the partitions on the 500gb and using that as a data drive. All was well for a few reboots but then I started to get "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER" messages. If I put the Win7 install DVD back in the drive it boots fine. Tried a clean install again, after replacing SATA cables and swapping SATA ports, with a complete partition wipe of both drives. Again, rebooted fine a few times then back with the "DISK BOOT FAILURE" error. Looked on the web and found some discussions about it so I then started from scratch again. This time I wiped the MBR on both drives using MBRWork, disconnected the 500gb and reinstalled to the SSD. Removed the install DVD and installed all the drivers which involved many reboots, all with no problem. To make sure I also did a few cold boots as well. Reconnected the 500gb, initialised, partitioned and formatted it. Copied data to it and did some more reboots and shutdowns. All was ok. Then out of the blue comes another "DISK BOOT FAILURE" and again, if the Win7 install DVD is in the drive it boots fine. So, is the SSD a bad'un? TIA UPDATE: It was a BIOS issue! I found a hidden away option for HDD boot order, which was separate from the usual HDD/CDRom/FDD boot order option. The WD was set to boot before the SSD... Swapped them round and all is well. Still don't understand how it worked at first though... Thanks Solaris

  Read the article

• smartctl short test doesn't seem to complete

  - by Cédric COPY

  I am working on project which involve automated HDD testing through smartctl. The station is working fine on most product, but I have two specific products that fail the smartctl test. Those two product are both WD product (WD2500BUDT series) Smartctl behaviour is quite strange, in fact the test is launched without any problem, i wait about 2min (test length), and when i check the smartctl, i have got no result at all. It's like I hadn't launched any test (no fail, no success in smartctl result). No error return on command, nothing in syslog, .. As i said before, the test is working for other product, thousands products worked well with this test. The main smartctl command used are : smarctl -t shortest /dev/sdX #Launch test smartctl -l selftest /dev/sdX #Look at test result I have tried to use: smartctl -s on /dev/sdX or smartctl -o on /dev/sdX But doesn't change anything. The system is using Debian 6.0, smartctl v5.40 (rev 3124) x86_64, HDD are plug through SATA to PCI controller. I have 4 HDD connected at a time. Well if anyone has some hints to give with this problem, because I have no idea how can i fix this. Thanks in advance. PS: Not sure if it was a serverfault topic, sorry if i was wrong!

  Read the article

• Install VirtualBox on Ubuntu 12.04.1 (on [Samsung] Chromebook)

  - by iphonedev7

  I have dual booted Ubuntu Linux 12.04.1 LTS on my Samsung Series 5 ChromeBook, and am trying to run/install Oracle VirtualBox (from the generic .run file downloaded from their website). However, every time I try to run it (as root from the command line), it gives me the following error occurs: Please install the build and header files for your current Linux kernel. The current kernel version is 3.4.0 Problems were found which would prevent VirtualBox from installing. I have tried the version from the Software Center, as well as the command line installation, both of which gave me errors based on my linux-headers/linux-kernel/linux-[kernel]-image. Here's an error I keep getting (on the command line): First Installation: checking all kernels... It is likely that 3.4.0 belongs to a chroot's host Building only for 3.5.0-18-generic Building initial module for 3.5.0-18-generic ERROR (dkms apport): kernel package linux-headers-3.5.0-18-generic is not supported Error! Bad return status for module build on kernel: 3.5.0-18-generic (x86_64) Consult /var/lib/dkms/virtualbox/4.1.12/build/make.log for more information. Setting up virtualbox-qt (4.1.12-dfsg-2ubuntu0.2) ... Processing triggers for libc-bin ... ldconfig deferred processing now taking place ...And one of the more cryptic errors I get when trying to start any Virtual Machine: Result Code: NS_ERROR_FAILURE (0x80004005) Component: Machine Interface: IMachine {5eaa9319-62fc-4b0a-843c-0cb1940f8a91}

  Read the article

• No video signal at boot with custom built computer

  - by Bart Pelle

  After booting my custom built computer, neither the VGA nor the HDMI methods from the video card seem to emit any signal to the display. I have tested both a regular VGA screen and a modern HDMI screen. Both did not receive signal. Below are the specifications from my computer build: Intel Core i5 3350P ASRock B75 Pro 3-M Seagate Barracuda 7200.14 ST1000 DM003 1000GB Corsair Vengeance LP CML 8GX 3M2 A1600 CGB Blue (2 cards) Cooler Master B Series B600 Club 3D Radeon HD7870 XT Jokercard Samsung SH-224 BB Black Sharkoon T28 Case The motherboard does not emit any beeps on startup. The CD tray opens properly and all fans spin. All cables are properly connected. All components are new and no damage was found on any of the components. The fans on the GPU spin aswell. The VGA test we did was by using the onboard graphics from the Intel i5, but this gave no result. The HDMI test was from the GPU which did not emit any signal either. We have not been able to test out the DVI, could this be important to test, even though all the other methods did not work? Thank you for your time and hopefully reply.

  Read the article

• Mystery 0xc0000142 error on starting java from a service, as a different user.

  - by cpf

  This is a very convoluted setup, but effectively this is what goes down: Manager service (which I don't have control over) running as admin user X starts my executable, which then starts Java as user Y using the standard c# StartInfo.Username/Password controls. Now, from a basic (not elevated or anything, just admin) command prompt I can run that executable, and Java pops up and works fine, running perfectly under the user it should be. When the service runs the same executable, however, Java silently fails. The only hint I see is this series of events in the event viewer: Service starts "Application popup: java.exe - Application Error : The application was unable to start correctly (0xc0000142). Click OK to close the application. " (googling this reveals a lot of scam sites telling me to use their "free antivirus to fix 0xc0000142 errors easy!"... sigh) Service stops (the java shutdown propagated, which is supposed to happen) And here's what process explorer has for the failure: As you can see, everything shows as a success. Now, I think this might have something to do with the permissions (the user java.exe is running under has traverse permission for the entire drive and full permissions to Directory A, which is where the .jar is), but I just can't fathom how something that works fine from the command line (and, this is an upgrade, the previous system without the user-switching aspect works fine from the service) can fail with such a cryptic message and little showing up in logs.

  Read the article

• Windows Server 2008 R2 Virtual Network Setup

  - by jpearl01

  Hi all, Some background: I'm very much new to networking in general, and virtualization in particular. I'm trying to set up a series of VMs as we are transitioning to a thin client setup. I have been supplied a limited number of static ip addresses. The server is located in an offsite building which houses the network we use to connect to the internet, share folders etc. The setup I've been trying to go for is this: The host OS (Windows Server 2008 R2) is bound to one nic using one of the static ips (say, Nic1 and ip 10.255.6.61). I've set up another external virtual network attached to another physical nic , and a virtual private network attached to no nic. There is one VM running the same os (as the host). This VM is connected to both the external virtual network (and uses another static ip say Nic2 and ip 10.255.6.62) and also to the virtual private network (I gave it a static random ip 192.168.88.1 subnet mask 255.255.255.0). This virtual private network is connected to all the other VMs. I'd like to share the internet connection with all the other VMs on the private virtual network, and so I installed the RRAS role on the server connected to Nic2, and selected the option to share the internet over the vpn. I've run through the RRAS wizard a few times, trying different configurations, but none of them seem to be letting the other vms connect to the 'net. The vms seem to connect to the virtual private network fine, they are assigned an ip address and everything, but no internet, and no rest of the network either. The other problem is in general I connect to the vms with RDP. Will that be possible with a setup like this? i.e. will the vms show up as computers on the network? If not, what are my other options? Thanks! ~josh

  Read the article

• Xmonad on windows laptop

  - by Kevin L.

  I'm a Linux developer in the market for a laptop. 90% of my time is spent in Emacs, the terminal, and Google Chrome, and I want to use them within the excellent Xmonad tiling windows manager. Given these constraints, I can only see two options: Run Linux on a laptop Run Windows on the laptop, and spend all of my time working within a Linux VM. Years of experience suggest that the first option will take many frustrating hours and probably be suboptimal w.r.t. battery life, wifi, and fn keys like screen brightness or audio adjustment. For the second option, what would be the ideal setup? I've had a lot of luck with Cooperative Linux on my Samsung NC-10 netbook (Windows XP), but I would have to setup the X11 server myself. What about using VirtualBox (which includes the guest VM's GUI)? Has anyone tried this? Hardware-wise, I'm looking for something in the "Macbook Air killer" category; Samsung Series 9 laptop, Lenovo IdeaPad U300s, &c. (i.e., matte screen, 5h+ battery life, 3ish pound weight). Price is not a consideration; any suggestions?

  Read the article

• How to encourage Windows administrators to pick up scripting?

  - by icelava

  When I worked as an administrator in my first job, I was frustrated that our administration processes with Windows servers were a series of point-and-clicks; we could never match the level of efficiency with the Unix servers which had a group of shell scripts to automate a lot of the work. I soon read about WSH and ADSI and wasted no time learning just how much automation I was able to achieve with scripting. There was a huge problem though - almost none of my Windows colleagues were really interested in learning scripting. They seemed happy with the manually mouse-clicking chores and were never excited at the prospect of using scripts to do the work on their behalf. I struggled to convince them to pick up scripting skills despite the evident increases in efficiency. I left that job in pursuit of a full-time software development career thereafter. Almost a decade on working in various environments and different customers, I still encounter Windows administrators mainly possessing this general "mood" where they would avoid scripting as much as possible. Despite the increasing level of accessibility Windows server technologies are opening up for scripting and automation. I am almost certain the majority of administrators are administrators precisely because they absolutely hate performing any kind of programming duties. What are some means to encourage and motivate administrators that scripting can really help them in the long run?

  Read the article

• Bad Mumble control channel performance in KVM guest

  - by aef

  I'm running a Mumble server (Murmur) on a Debian Wheezy Beta 4 KVM guest which runs on a Debian Wheezy Beta 4 KVM hypervisor. The guest machines are attached to a bridge device on the hypervisor system through Virtio network interfaces. The Hypervisor is attached to a 100Mbit/s uplink and does IP-routing between the guest machines and the remaining Internet. In this setup we're experiencing a clearly recognizable lag between double-clicking a channel in the client and the channel joining action happening. This happens with a lot of different clients between 1.2.3 and 1.2.4 on Linux and Windows systems. Voice quality and latency seems to be completely unaffected by this. Most of the times the client's information dialog states a 16ms latency for both the voice and control channel. The deviation for the control channels mostly is a lot higher than the one of the voice channels. In some situations the control channel is displayed with a 100ms ping and about 1000 deviation. It seems the TCP performance is a problem here. We had no problems on an earlier setup which was in principle quite like the new one. We used Debian Lenny based Xen hypervisor and a soft-virtualised guest machine instead and an earlier version of the Mumble 1.2.3 series. The current murmurd --version says: 1.2.3-349-g315b5f5-2.1

  Read the article

• Setting up xpra for client use in OS X

  - by Jonathan

  I've been trying to get xpra to run on OS X for the last few days to connect to my Ubuntu server. Note that there's a GUI for it called shifter, but that (at least on OS X) is still far too buggy. For those who don't know what xpra is, if you know what screen is, it's like screen for GUI X Windows apps tunneled over ssh. You can render a remote X app locally so it's faster than sending a series of compresses screen shots (like VNC), but with xpra you can disconnect and reconnect on different computers. To get the basic functionality you can just type "ssh -X server.location" and any GUI app you open from the command line will open locally. I've been able to get xpra to build by doing the following: Download pari-all-0.0.6.tar.gz from the xpra site listed under upstream and untar it. Issue the following Mac Ports command (Dependencies thanks to RogBlog): sudo port install python25 python26 py26-pyrex py26-gtk xorg-libXtst py25-gobject py25-gtk py25-nose py26-nose xorg-libXdamage xorg-libXcomposite xorg-libXtst xorg-libXfixes In the upstream list of v0.0.06 patches (NOT 0.0.8pre!) on the xpra site listed above, download mswindows-conditional-pyrex.patch. Open the patch with your favorite text editor and change the single occurrence of "win" in it to "darwin". Apply the patch to setup.py. Run do-build in the command line. Now where I'm stumped: how do I run xpra? The build produces a sub directory called install/bin in which xpra is located, but when I try to run it I get the following error: Traceback (most recent call last): File "./xpra", line 4, in import xpra.scripts.main ImportError: No module named xpra.scripts.main There is a file called main.py under xpra/scripts, but I don't know any python and I'm not sure if this is what it's looking for, and what to do with it even if it is. My goal is to set up xpra so I can install it into /usr/bin (or some other common path for executables) and execute it whenever I please. What do I do next?

  Read the article

• Why does clicking on Windows 7 Printer Properties Result In Driver Not Installed?

  - by octopusgrabbus

  The question I need to ask is has anyone heard of getting a "driver not installed" error when clicking on a printer's properties on Windows 7, and is there a workaround? Here are the details of the problem. One of our users has a Windows 7 desktop, and an HP LaserJet 4050 T connected to via a parallel-to-usb converter. The PLC5 universal driver was installed for series 4050 printers. I needed to install the PLC 6 driver, which completed successfully. The user is an administrator of the system, and I was prompted to and accepted running as Administrator to install the driver. After the install, I went to see the 4050's properties and was prompted that the PLC6 driver was not installed. I believe the PLC6 driver was installed, because the PLC5 driver resulted in receiving an official HP error page indicating the printer was "not set up for collating" as the second page of printing two copies of a one page email. This problem did not occur with the PLC 6 driver. Oddly enough, setting back to PLC5 produced the same error about the PLC5 driver not being installed. I ignored/dismissed the error box (did not re-install the driver), and reproduced the error, with the second page being the HP not set up for collating error page. Any thoughts on what is causing this and how to clear it would be appreciated. The closest fix I could find was on a Microsoft tech page, and they had me clear winsock out of a Administrator run command line, followed by a reboot. That did not fix the problem. I have also found this http://social.technet.microsoft.com/Forums/windowsserver/en-US/5101195b-3aca-4699-9a06-db4578614e2d/changing-driver-results-in-printer-driver-is-not-installed-error-on-server-2008?forum=winserverprint and will look into trying some of these suggestions, which appear to me to be a "shotgun" approach to fixing the problem.

  Read the article

• Building vs buying a server for an academic lab [closed]

  - by Roy

  I'm looking for advice on the classic build vs buy question. We need a new linux server to run Matlab computation on in our lab (academic). Matlab parallel computing toolbox licence allows up to 12 local workers so we are aiming at a 12 core server with 4GB memory per core (total of 48gb). The system will have an SSD for the OS and a raid-5 (4x2tb) for data. I looked around and found a (relatively) cheap vendor, Silicon Mechanics, that offers a system to our liking (specs below) for $6732. However, buying the components from newegg cost only $4464! The difference is $2268 which is 50% of the base cost. If buying from a company can be thought of as a sort of insurance, basically my premiums are of 50% of the base cost which to me sounds like a lot. Of course any downtime is bad, but the work is not "mission critical", i.e. if it takes a few days to fix it when it breaks its no the end of the world. If it takes weeks to months then its a problem. If it breaks 2-3 times in 3 years, not too bad. If it breaks every month not good. In term of build experience, I set up a linux cluster in grad school (from existing computers) and I build my home pcs but I never built a server before. The server components I'm thinking about: 1 x SUPERMICRO SYS-7046T-6F 4U Tower Server Barebone Dual LGA 1366 Intel 5520 DDR3 1333/1066/800 ($1,050) 12 x Kingston 4GB 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) ECC Unbuffered Server Memory ($420) 2 x Intel Xeon E5645 Westmere-EP 2.4GHz LGA 1366 80W Six-Core ($1,116) 4 x Seagate Constellation ES 2TB 7200 RPM SATA 6.0Gb/s 3.5" ($1,040) 1 x SAMSUNG Internal DVD Writer Black SATA ($20) 1 x Intel 520 Series 2.5" 180GB SATA III MLC SSD $300 1 x LSI LSI00281 PCI-Express 2.0 x8 MD2 Low profile SATA / SAS MegaRAID SAS 9260CV-4i Controller Card, $695

  Read the article

• How to encourage Windows administrators to pick up scripting

  - by icelava

  When i worked as an administrator in my first job, I was frustrated our administration processes with Windows servers were a series of point-and-clicks; we could never match the level of efficiency with the Unix servers which had a group of shell scripts to automate a lot of the work. I soon read about WSH and ADSI and wasted no time learning just how much automation I was able to achieve with scripting. There was a huge problem though - almost none of my Windows colleagues were really interested in learning scripting. They seemed happy with the manually mouse-clicking chores and were never excited at the prospect of using scripts to do the work on their behalf. I struggled to convince them to pick up scripting skills despite the evident increases in efficiency. I left that job in pursuit of a full-time software development career thereafter. Almost a decade on working in various environments and different customers, I still encounter Windows administrators mainly possessing this general "mood" where they would avoid scripting as much as possible. Despite the increasing level of accessibility Windows server technologies are opening up for scripting and automation. I am almost certain the majority of administrators are administrators precisely because they absolutely hate performing any kind of programming duties. What are some means to encourage and motivate administrators that scripting can really help them in the long run?

  Read the article

• Simple way to set up port knocking on Linux?

  - by Ace Paus

  There are well known benefits of Port Knocking utilities when utilized in combination with firewall IP table modification. Port Knocking is best used to provide an additional layer of security over other tools such as the OpenSSH server. I would like some help setting it up on a ubuntu server. I looked at some port knocking implementations here: PORTKNOCKING - A system for stealthy authentication across closed ports. IMPLEMENTATIONS http://www.portknocking.org/view/implementations fwknop looked good. I found an Android client here. And fwknop (both client and server) is in the ubuntu repos. Unfortunately, setting it up (on the server) looks difficult. I do not have iptables set up. My proficiency with iptables is limited (but I understand the basics). I'm looking for a series of simple steps to set it up. I only want to open the SSH port in response to a valid knock. Alternatively, I would consider other port knocking implementations, if they are much simpler to set up and the desired Linux and Android clients are available.

  Read the article

< Previous Page | 148 149 150 151 152 153 154 155 156 157 158 159  | Next Page >