Search Results

Search found 33971 results on 1359 pages for 'ask and learn'.

Page 153/1359 | < Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >

• How do I make changes to /proc/acpi/wakeup permanent?

  - by Jolan

  I had a problem with my Ubuntu 12.04 waking up immediately after going into suspend. I solved the problem by changing the settings in /proc/acpi/wakeup, as suggested in this question: How do I prevent immediate wake up from suspend?. After changing the settings, the system goes flawlessly into suspend and stays suspended, but after I wake it back up, the settings in /proc/acpi/wakeup are different from what I set them to. Before going to suspend: cat /proc/acpi/wakeup Device S-state Status Sysfs node SMB0 S4 *disabled pci:0000:00:03.2 PBB0 S4 *disabled pci:0000:00:09.0 HDAC S4 *disabled pci:0000:00:08.0 XVR0 S4 *disabled pci:0000:00:0c.0 XVR1 S4 *disabled P0P5 S4 *disabled P0P6 S4 *disabled pci:0000:00:15.0 GLAN S4 *enabled pci:0000:03:00.0 P0P7 S4 *disabled pci:0000:00:16.0 P0P8 S4 *disabled P0P9 S4 *disabled USB0 S3 *disabled pci:0000:00:04.0 USB2 S3 *disabled pci:0000:00:04.1 US15 S3 *disabled pci:0000:00:06.0 US12 S3 *disabled pci:0000:00:06.1 PWRB S4 *enabled SLPB S4 *enabled I tell the system to suspend, and it works as it should. But later after waking it up, the settings are changed to either: USB0 S3 *disabled pci:0000:00:04.0 USB2 S3 *enabled pci:0000:00:04.1 US15 S3 *disabled pci:0000:00:06.0 US12 S3 *enabled pci:0000:00:06.1 or USB0 S3 *enabled pci:0000:00:04.0 USB2 S3 *enabled pci:0000:00:04.1 US15 S3 *enabled pci:0000:00:06.0 US12 S3 *enabled pci:0000:00:06.1 Any ideas? Thank you for your response. Unfortunately it did not solve my problem. all of /sys/bus/usb/devices/usb1/power/wakeup /sys/bus/usb/devices/usb2/power/wakeup /sys/bus/usb/devices/usb3/power/wakeup /sys/bus/usb/devices/usb4/power/wakeup as well as /sys/bus/usb/devices/3-1/power/wakeup are set to disabled, and the notebook still wakes up by itself right after going to sleep. The only thing it seems to react to are the settings in /proc/acpi/wakeup, which keep changing (resetting) every time i power off/restart my notebook.

  Read the article

• Winetricks fails to find program files directory

  - by EgyptLovesUbuntu

  I installed a fresh copy of Ubuntu 12 desktop then: Installed WINE from the Ubuntu Software Center. Installed WineTricks from the Ubuntu Software Center. When I type the following commands in the terminal: sudo winetricks dotnet40 I get this error message: wine cmd.exe /c echo '%ProgramFiles%' returned empty string If i try the command without sudo winetricks dotnet40 The output is as follows Executing w_do_call dotnet40 Executing load_dotnet40 ------------------------------------------------------ dotnet40 does not yet fully work or install on wine. Caveat emptor. ------------------------------------------------------ Executing mkdir -p /home/vectoruser/.cache/winetricks/dotnet40 mkdir: cannot create directory `/home/vectoruser/.cache/winetricks/dotnet40': Permission denied ------------------------------------------------------ Note: command 'mkdir -p /home/vectoruser/.cache/winetricks/dotnet40' returned status 1. Aborting. ------------------------------------------------------ My current user is vectoruser which i use to logon to Ubuntu The output of ls -ld /home/vectoruser /home/vectoruser/.cache /home/vectoruser/.cache/winetricks Gives: drwxr-xr-x 32 vectoruser vectoruser 4096 Aug 2 19:26 /home/vectoruser drwx------ 19 vectoruser vectoruser 4096 Aug 2 19:25 /home/vectoruser/.cache drwxr-xr-x 2 root root 4096 Aug 2 18:09 /home/vectoruser/.cache/winetricks

  Read the article

• How can a gamepad control THE mouse?

  - by Boris

  There are many questions about this subject: Remapping both mouse and keyboard to a gamepad How do I configure a joystick or gamepad? How to control the mouse pointer via my keyboard? ... But the purpose of these questions/answers is to be able to use the gamepad for playing a game. I would a like a solution to use the gamepad to control THE mouse. To replace the mouse by the gamepad in all applications. That way I could control my computer in the living-room from my couch with a wireless gamepad.

  Read the article

• Installing CUDA on Ubuntu 12.04 with nvidia driver 295.59

  - by johnmcd

  I have been trying to get cuda to run on a nvidia gt 650m based laptop. I am running Ubuntu 12.04 with the nvidia 295.59 driver. Also, my laptop uses Optimus so I have install the driver via bumblebee. Bumblebee is not working correctly yet -- however I believe it is possible to install CUDA independently. To install CUDA I have followed the instructions detailed here: How can I get nVidia CUDA or OpenCL working on a laptop with nVidia discrete card/Intel Integrated Graphics? However I am still running into problem building the sdk. I made the changes specified at the above link in common.mk, but I got the following (snippet) from the build process: make[2]: Entering directory `/home/john/NVIDIA_GPU_Computing_SDK/C/src/fluidsGL' /usr/bin/ld: warning: libnvidia-tls.so.302.17, needed by /usr/lib/nvidia-current/libGL.so, not found (try using -rpath or -rpath-link) /usr/bin/ld: warning: libnvidia-glcore.so.302.17, needed by /usr/lib/nvidia-current/libGL.so, not found (try using -rpath or -rpath-link) /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv018tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv012glcore' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv017glcore' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv012tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv015tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv019tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv000glcore' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv017tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv013tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv013glcore' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv018glcore' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv022tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv007tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv009tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv020tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv014glcore' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv015glcore' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv016tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv001glcore' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv006tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv021tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv011tls' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv020glcore' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv019glcore' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv002glcore' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv021glcore' /usr/lib/nvidia-current/libGL.so: undefined reference to `_nv014tls' collect2: ld returned 1 exit status make[2]: *** [../../bin/linux/release/fluidsGL] Error 1 make[2]: Leaving directory `/home/john/NVIDIA_GPU_Computing_SDK/C/src/fluidsGL' make[1]: *** [src/fluidsGL/Makefile.ph_build] Error 2 make[1]: Leaving directory `/home/john/NVIDIA_GPU_Computing_SDK/C' make: *** [all] Error 2 The libraries that ld warns about are on my system and are installed on the system: $ locate libnvidia-tls.so.302.17 libnvidia-glcore.so.302.17 /usr/lib/nvidia-current/libnvidia-glcore.so.302.17 /usr/lib/nvidia-current/libnvidia-tls.so.302.17 /usr/lib/nvidia-current/tls/libnvidia-tls.so.302.17 /usr/lib32/nvidia-current/libnvidia-glcore.so.302.17 /usr/lib32/nvidia-current/libnvidia-tls.so.302.17 /usr/lib32/nvidia-current/tls/libnvidia-tls.so.302.17 however /usr/lib/nvidia-current and /usr/lib32/nvidia-current are not being picked up by ldconfig. I have tried adding them by adding a file to /etc/ld.so.conf.d/ which gets past this error, however now I am getting the following error: make[2]: Entering directory `/home/john/NVIDIA_GPU_Computing_SDK/C/src/deviceQueryDrv' cc1plus: warning: command line option ‘-Wimplicit’ is valid for C/ObjC but not for C++ [enabled by default] obj/x86_64/release/deviceQueryDrv.cpp.o: In function `main': deviceQueryDrv.cpp:(.text.startup+0x5f): undefined reference to `cuInit' deviceQueryDrv.cpp:(.text.startup+0x99): undefined reference to `cuDeviceGetCount' deviceQueryDrv.cpp:(.text.startup+0x10b): undefined reference to `cuDeviceComputeCapability' deviceQueryDrv.cpp:(.text.startup+0x127): undefined reference to `cuDeviceGetName' deviceQueryDrv.cpp:(.text.startup+0x16a): undefined reference to `cuDriverGetVersion' deviceQueryDrv.cpp:(.text.startup+0x1f0): undefined reference to `cuDeviceTotalMem_v2' deviceQueryDrv.cpp:(.text.startup+0x262): undefined reference to `cuDeviceGetAttribute' deviceQueryDrv.cpp:(.text.startup+0x457): undefined reference to `cuDeviceGetAttribute' deviceQueryDrv.cpp:(.text.startup+0x4bc): undefined reference to `cuDeviceGetAttribute' deviceQueryDrv.cpp:(.text.startup+0x502): undefined reference to `cuDeviceGetAttribute' deviceQueryDrv.cpp:(.text.startup+0x533): undefined reference to `cuDeviceGetAttribute' obj/x86_64/release/deviceQueryDrv.cpp.o:deviceQueryDrv.cpp:(.text.startup+0x55e): more undefined references to `cuDeviceGetAttribute' follow collect2: ld returned 1 exit status make[2]: *** [../../bin/linux/release/deviceQueryDrv] Error 1 make[2]: Leaving directory `/home/john/NVIDIA_GPU_Computing_SDK/C/src/deviceQueryDrv' make[1]: *** [src/deviceQueryDrv/Makefile.ph_build] Error 2 make[1]: Leaving directory `/home/john/NVIDIA_GPU_Computing_SDK/C' make: *** [all] Error 2 I would appreciate any help that anyone can provide me with. If I can provide any further information please let me know. Thanks.

  Read the article

• Display clock frequency per core using Conky

  - by cfbaptista

  I am using Conky to display a lot of information of my system. I managed to display the load percentage per core. But I do not know how to display the clock frequency of each core. What I have now is: ${font sans-serif:bold:size=8}PROCESSORS ${hr 2}${font} CPU1: ${cpu cpu1}% $alignr ${freq} MHz $alignr ${cpubar cpu1 8,60} CPU2: ${cpu cpu2}% $alignr ${freq} MHz $alignr ${cpubar cpu2 8,60} CPU3: ${cpu cpu3}% $alignr ${freq} MHz $alignr ${cpubar cpu3 8,60} CPU4: ${cpu cpu4}% $alignr ${freq} MHz $alignr ${cpubar cpu4 8,60} CPU5: ${cpu cpu5}% $alignr ${freq} MHz $alignr ${cpubar cpu5 8,60} CPU6: ${cpu cpu6}% $alignr ${freq} MHz $alignr ${cpubar cpu6 8,60} CPU7: ${cpu cpu7}% $alignr ${freq} MHz $alignr ${cpubar cpu7 8,60} CPU8: ${cpu cpu8}% $alignr ${freq} MHz $alignr ${cpubar cpu8 8,60} But this only gives me the global clock frequency and not the individual clock frequency per core. Does someone know how to get the individual clock frequency per core? System information Linux Mint 13 KDE, 64 bit (based on Ubuntu 12.04) Intel i7-2670QM (quad core with multithreading)

  Read the article

• External usb 3.0 hard drive is not recognised when plugged into usb 3 port (ubuntu natty 64 bit).

  - by kimangroo

  I have an Iomega Prestige Portable External Hard Drive 1TB USB 3.0. It works fine on windows 7 as a usb 3.0 drive. It isn't detected on ubuntu natty 64bit, 2.6.38-8-generic. fdisk -l cannot see it at all: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1bed746b Device Boot Start End Blocks Id System /dev/sda1 1 1689 13560832 27 Unknown /dev/sda2 * 1689 1702 102400 7 HPFS/NTFS /dev/sda3 1702 19978 146805760 7 HPFS/NTFS /dev/sda4 19978 60802 327914497 5 Extended /dev/sda5 25555 60802 283120640 7 HPFS/NTFS /dev/sda6 19978 23909 31571968 83 Linux /dev/sda7 23909 25555 13218816 82 Linux swap / Solaris Partition table entries are not in disk order lsusb can see it: Bus 003 Device 003: ID 059b:0070 Iomega Corp. Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 004: ID 05fe:0011 Chic Technology Corp. Browser Mouse Bus 002 Device 003: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 005: ID 0489:e00f Foxconn / Hon Hai Bus 001 Device 004: ID 0c45:64b5 Microdia Bus 001 Device 003: ID 08ff:168f AuthenTec, Inc. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub And dmesg | grep -i xhci (I may have unplugged the drive and plugged it back in again after booting): [ 1.659060] pci 0000:04:00.0: xHCI HW did not halt within 2000 usec status = 0x0 [ 11.484971] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 11.484997] xhci_hcd 0000:04:00.0: setting latency timer to 64 [ 11.485002] xhci_hcd 0000:04:00.0: xHCI Host Controller [ 11.485064] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 [ 11.636149] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 [ 11.636241] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X [ 11.636246] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X [ 11.636251] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X [ 11.636256] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X [ 11.636261] xhci_hcd 0000:04:00.0: irq 47 for MSI/MSI-X [ 11.639654] xHCI xhci_add_endpoint called for root hub [ 11.639655] xHCI xhci_check_bandwidth called for root hub [ 11.956366] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 2 [ 12.001073] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.007059] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.012932] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.018922] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.049139] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.056754] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.131607] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 12.179717] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.686876] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 12.687058] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 12.687152] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 43.330737] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 2 [ 43.422579] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 43.422658] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af00 [ 43.422665] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af40 [ 43.422671] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af80 [ 43.422677] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669afc0 [ 43.531159] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 125.160248] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.766466] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 3 [ 903.807789] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.813530] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.819400] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.825104] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.855067] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862314] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862597] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.913211] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 904.424416] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 904.424599] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 904.424700] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 935.139021] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 3 [ 935.226075] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 935.226140] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b00 [ 935.226148] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b40 [ 935.226153] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b80 [ 935.226159] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186bc0 [ 935.343339] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst I thought it might be that the firmware wasn't compatible with linux or something, but when booting a live image of partedmagic, (2.6.38.4-pmagic), the drive was detected fine, I could mount it and got usb 3.0 speeds (at least they double the speeds I got from plugging same drive in usb 2 ports). dmesg in partedmagic did say something about no SuperSpeed endpoint which was an error I saw in a previous dmesg of ubuntu: Jun 27 15:49:02 (none) user.info kernel: [ 2.978743] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Jun 27 15:49:02 (none) user.debug kernel: [ 2.978771] xhci_hcd 0000:04:00.0: setting latency timer to 64 Jun 27 15:49:02 (none) user.info kernel: [ 2.978781] xhci_hcd 0000:04:00.0: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 2.978856] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 Jun 27 15:49:02 (none) user.info kernel: [ 3.089458] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 Jun 27 15:49:02 (none) user.debug kernel: [ 3.089541] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089544] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089546] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089548] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089550] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X Jun 27 15:49:02 (none) user.warn kernel: [ 3.092857] usb usb3: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values Jun 27 15:49:02 (none) user.info kernel: [ 3.092864] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 Jun 27 15:49:02 (none) user.info kernel: [ 3.092866] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Jun 27 15:49:02 (none) user.info kernel: [ 3.092867] usb usb3: Product: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 3.092869] usb usb3: Manufacturer: Linux 2.6.38.4-pmagic xhci_hcd Jun 27 15:49:02 (none) user.info kernel: [ 3.092870] usb usb3: SerialNumber: 0000:04:00.0 Jun 27 15:49:02 (none) user.debug kernel: [ 3.092961] xHCI xhci_add_endpoint called for root hub Jun 27 15:49:02 (none) user.debug kernel: [ 3.092963] xHCI xhci_check_bandwidth called for root hub Well I have no idea what's going wrong, and I haven't had much luck from google and the forums so far. A number of unanswered threads with people with similar error messages and problems only. Hopefully someone here can help or point me in the right direction?!

  Read the article

• Ubuntu won't install from Live CD

  - by Erik Shank

  Complete noob here. I am trying to install Ubuntu 12.04 from a Live CD. I told the computer to boot from the CD (it does) & it reads the CD & then quits with the Ubuntu dots just freezing. I checked the disk & did the memory test, both OK. I also did the nomodeset in the start-up line. Hit escape when it froze but there were no msgs. Have also tried Ubuntu 12.10 & Dream Studio, same thing. Anyone have any ideas? Thanks! Erik The Pope

  Read the article

• Create bootable USB install image from command line?

  - by j-g-faustus

  I'm trying to create a bootable USB image to install Ubuntu on a new computer. I have done this before following the "create USB drive" instructions for Ubuntu desktop, but I don't have an Ubuntu desktop available. How can I do the same using only the command line? Things I've tried: Create bootable USB on Mac OS X following the ubuntu.com "create USB drive" instructions for Mac: Doesn't boot. usb-creator: According to apt-cache search usb-creator and Wikipedia usb-creator only exists as a graphical tool. "Create manually" instructions at help.ubuntu.com: None of the files and directories described (e.g. casper, filesystem.manifest, menu.lst) exist in the ISO image, and I don't know what has replaced them. (At my disposal is Mac OS X and Ubuntu server; I have neither Ubuntu desktop nor Windows.)

  Read the article

• How to use XDMCP+GDM and Xnest?

  - by João Pinto

  I have been trying to enable XDMCP on GDM without much success. Following some instructions I have edited /etc/gdm/custom.conf and added: [daemon] RemoteGreeter=/usr/lib/gdm/gdm-xdmcp-chooser-slave [xdmcp] Enable=true Then restarted gdm and tried to connect both locally and from a remote system with: Xnest :1 -query localhost Xnest :1 -query remote_system_hostname I just get a black screen instead of the GDM window as expected. I am missing something ?

  Read the article

• Installing raid 5 on a pre-installed ubuntu server. 12.04

  - by Chris

  I have a ubuntu server with samba already set up and installed with a 1tb hdd. I am wanting to now install 3 more 1tb drives and create a raid array using raid 5. I have found a lot of documentation about installing raid when installing and setting up ubuntu server for the first time. However, I am struggling to find anything on installing a raid 5 array on a system already installed an configured. Can this be done, or does a clean install need to be done again?

  Read the article

• Forked-daapd with alternative soundcard

  - by Mah

  I am trying to configure forked-daapd on my computer, and everything goes well except that in configuration file I can not set a new value for the line corresponding to soundcard. This is the default code in the config file: #card = "default" I want to use a soundcard called "DG2", which is the soundcard no.1 and has a first device that ALSA recognizes as no.0. So, I change the line to the following: card = "hw:DG2,0" I restart the daapd service and the next time I play a file through iTune remote, I get a message in my server log file saying that it can not play the file because the device is busy. Any change in the device name will return a different error, saying that the device does not exist. I am pretty sure no other uses this external device, and I don't understand why I get this message. I have tried hwplug as well, with no result.

  Read the article

• Cannot install Acrobat Reader on Ubuntu 12.04.1

  - by user91137

  I have been trying to install Acrobat Reader on my Ubuntu 12.04.1. In the be;ggining, I tried to install it from the software-center, but it crashes with the report: (Reading database ... 189311 files and directories currently installed.) Unpacking acroread (from .../acroread_9.5.1-1precise1_i386.deb) ... dpkg: error processing /var/cache/apt/archives/acroread_9.5.1-1precise1_i386.deb (--unpack): trying to overwrite '/usr/bin/acroread', which is also in package adobereader-ptb 8.1.7-2 No apport report written because MaxReports is reached already Processing triggers for desktop-file-utils ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for gnome-menus ... Processing triggers for man-db ... Errors were encountered while processing: /var/cache/apt/archives/acroread_9.5.1-1precise1_i386.deb" As as solution, I tried to install it via terminal, with the $sudo apt-get install acroread and receive the following: arcanjo@arcanjo:~$ sudo apt-get install acroread Lendo listas de pacotes... Pronto Construindo árvore de dependências Lendo informação de estado... Pronto Pacotes sugeridos: libldap2 libgnome-speech7 Os NOVOS pacotes a seguir serão instalados: acroread 0 pacotes atualizados, 1 pacotes novos instalados, 0 a serem removidos e 0 não atualizados. É preciso baixar 60,1 MB de arquivos. Depois desta operação, 142 MB adicionais de espaço em disco serão usados. Obter:1 http://archive.canonical.com/ubuntu/ precise/partner acroread i386 9.5.1-1precise1 [60,1 MB] Baixados 60,1 MB em 4min 17s (234 kB/s) (Lendo banco de dados ... 189311 ficheiros e directórios actualmente instalados.) Desempacotando acroread (de .../acroread_9.5.1-1precise1_i386.deb) ... dpkg: erro processando /var/cache/apt/archives/acroread_9.5.1-1precise1_i386.deb (--unpack): a tentar sobre-escrever '/usr/bin/acroread', que também está no pacote adobereader-ptb 8.1.7-2 Nenhum relatório apport escrito pois MaxReports já foi atingido Processando gatilhos para desktop-file-utils ... Processando gatilhos para bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processando gatilhos para gnome-menus ... Processando gatilhos para man-db ... Erros foram encontrados durante o processamento de: /var/cache/apt/archives/acroread_9.5.1-1precise1_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) arcanjo@arcanjo:~$ I've already tried to upgrade and update the apt-get, also tried to remove and re-install the software-center, tried deleting the "problematic" files and re-updating the apt-get... Nothing seems to work... Any solutions?

  Read the article

• Ubuntu 11.10 - Everytime i am trying to connect to my box using SSH, its failing not connecting

  - by YumYumYum

  From any other PC doing SSH to my Ubuntu 11.10,is failing. Even the SSH is running: Other PC: retrying over and over $ ping 192.168.0.128 PING 192.168.0.128 (192.168.0.128) 56(84) bytes of data. From 192.168.0.226 icmp_seq=1 Destination Host Unreachable From 192.168.0.226 icmp_seq=2 Destination Host Unreachable From 192.168.0.226 icmp_seq=3 Destination Host Unreachable From 192.168.0.226 icmp_seq=4 Destination Host Unreachable $ sudo service iptables stop Stopping iptables (via systemctl): [ OK ] $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] Connection closed by 192.168.0.128 $ ssh [email protected] [email protected]'s password: Connection closed by UNKNOWN $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host $ ssh [email protected] ssh: connect to host 192.168.0.128 port 22: No route to host Follow up: -- checked cable -- using cable tester and other detectors -- no problem found in cable -- used random 10 cables -- adapter is not broken -- checked it using circuit tester by opening the system (card is new so its not network adapter card problem) -- leds are OK showing -- used LiveCD and did same ping test was having same problem -- disabled ipv6 100% to make sure its not the cause -- disabled iptables 100% so its also not the issue -- some more info $ sudo killall dnsmasq -- did not solved the problem -- -- like many other Q/A was suggesting this same --- $ iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination $ netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 $ ssh -vvv [email protected] OpenSSH_5.6p1, OpenSSL 1.0.0j-fips 10 May 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 192.168.0.128 [192.168.0.128] port 22. debug1: Connection established. debug3: Not a RSA1 key file /home/sun/.ssh/id_rsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/sun/.ssh/id_rsa type 1 debug1: identity file /home/sun/.ssh/id_rsa-cert type -1 debug1: identity file /home/sun/.ssh/id_dsa type -1 debug1: identity file /home/sun/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],[email protected],[email protected],ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 118/256 debug2: bits set: 539/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: host 192.168.0.128 filename /home/sun/.ssh/known_hosts debug3: check_host_in_hostfile: match line 139 debug1: Host '192.168.0.128' is known and matches the RSA host key. debug1: Found key in /home/sun/.ssh/known_hosts:139 debug2: bits set: 544/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/sun/.ssh/id_rsa (0x213db960) debug2: key: /home/sun/.ssh/id_dsa ((nil)) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/sun/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/sun/.ssh/id_dsa debug3: no such identity: /home/sun/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password: debug3: packet_send2: adding 64 (len 60 padlen 4 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). Authenticated to 192.168.0.128 ([192.168.0.128]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env ORBIT_SOCKETDIR debug3: Ignored env XDG_SESSION_ID debug3: Ignored env HOSTNAME debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE_PID debug3: Ignored env IMSETTINGS_INTEGRATE_DESKTOP debug3: Ignored env GPG_AGENT_INFO debug3: Ignored env TERM debug3: Ignored env HARDWARE_PLATFORM debug3: Ignored env SHELL debug3: Ignored env DESKTOP_STARTUP_ID debug3: Ignored env HISTSIZE debug3: Ignored env XDG_SESSION_COOKIE debug3: Ignored env GJS_DEBUG_OUTPUT debug3: Ignored env WINDOWID debug3: Ignored env GNOME_KEYRING_CONTROL debug3: Ignored env QTDIR debug3: Ignored env QTINC debug3: Ignored env GJS_DEBUG_TOPICS debug3: Ignored env IMSETTINGS_MODULE debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env USERNAME debug3: Ignored env SESSION_MANAGER debug3: Ignored env GIO_LAUNCHED_DESKTOP_FILE debug3: Ignored env PATH debug3: Ignored env MAIL debug3: Ignored env DESKTOP_SESSION debug3: Ignored env QT_IM_MODULE debug3: Ignored env PWD debug1: Sending env XMODIFIERS = @im=none debug2: channel 0: request env confirm 0 debug1: Sending env LANG = en_US.utf8 debug2: channel 0: request env confirm 0 debug3: Ignored env KDE_IS_PRELINKED debug3: Ignored env GDM_LANG debug3: Ignored env KDEDIRS debug3: Ignored env GDMSESSION debug3: Ignored env SSH_ASKPASS debug3: Ignored env HISTCONTROL debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env GDL_PATH debug3: Ignored env GNOME_DESKTOP_SESSION_ID debug3: Ignored env LOGNAME debug3: Ignored env QTLIB debug3: Ignored env CVS_RSH debug3: Ignored env DBUS_SESSION_BUS_ADDRESS debug3: Ignored env LESSOPEN debug3: Ignored env WINDOWPATH debug3: Ignored env XDG_RUNTIME_DIR debug3: Ignored env DISPLAY debug3: Ignored env G_BROKEN_FILENAMES debug3: Ignored env COLORTERM debug3: Ignored env XAUTHORITY debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel_input_status_confirm: type 99 id 0 debug2: PTY allocation request accepted on channel 0 debug2: channel 0: rcvd adjust 2097152 debug2: channel_input_status_confirm: type 99 id 0 debug2: shell request accepted on channel 0 Welcome to Ubuntu 11.10 (GNU/Linux 3.0.0-12-generic x86_64) * Documentation: https://help.ubuntu.com/ 297 packages can be updated. 92 updates are security updates. New release '12.04 LTS' available. Run 'do-release-upgrade' to upgrade to it. Last login: Fri Jun 8 07:45:15 2012 from 192.168.0.226 sun@SystemAX51:~$ ping 19<--------Lost connection again-------------- Tail follow: -- dmesg is showing a very abnormal logs, like Ubuntu is automatically bringing the eth0 up, where eth0 is getting also auto down. [ 2025.897511] r8169 0000:02:00.0: eth0: link up [ 2029.347649] r8169 0000:02:00.0: eth0: link up [ 2030.775556] r8169 0000:02:00.0: eth0: link up [ 2038.242203] r8169 0000:02:00.0: eth0: link up [ 2057.267801] r8169 0000:02:00.0: eth0: link up [ 2062.871770] r8169 0000:02:00.0: eth0: link up [ 2082.479712] r8169 0000:02:00.0: eth0: link up [ 2285.630797] r8169 0000:02:00.0: eth0: link up [ 2308.417640] r8169 0000:02:00.0: eth0: link up [ 2480.948290] r8169 0000:02:00.0: eth0: link up [ 2824.884798] r8169 0000:02:00.0: eth0: link up [ 3030.022183] r8169 0000:02:00.0: eth0: link up [ 3306.587353] r8169 0000:02:00.0: eth0: link up [ 3523.566881] r8169 0000:02:00.0: eth0: link up [ 3619.839585] r8169 0000:02:00.0: eth0: link up [ 3682.154393] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 3899.866854] r8169 0000:02:00.0: eth0: link up [ 4723.978269] r8169 0000:02:00.0: eth0: link up [ 4807.415682] r8169 0000:02:00.0: eth0: link up [ 5101.865686] r8169 0000:02:00.0: eth0: link up How do i fix it? -- http://ubuntuforums.org/showthread.php?t=1959794 -- apt-get install openipml openhpi-plugin-ipml

  Read the article

• Wireless with WEP extremely slow on an Acer Timeline 4810T with a Centrino Wireless-N 1000

  - by noq38

  I've upgraded an Acer Timeline 4810T to Ubuntu 11.10. Everything works fine except for the darn wireless interface (network manager). I just tested the wireless interface over a non-encrypted signal and it works beautifully. The issue is definitely related to WEP. Unfortunately, some of the networks I need to connect to are WEP encrypted, therefore this is a serious issue for me that is preventing me from using Ubuntu on my laptop. This was no problem in 11.04 and prior. Is there a simple solution for this? Any suggestions? Here's more hardware information. Hopefully this helps to debug the network issue: sudo lshw -class network *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:3c:5e:e0 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-13-generic-pae firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:d2400000-d2401fff lspci 02:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no Many thanks for your help! I just tested the wireless interface over a non-encrypted signal and it works beautifully. The issue is definitely related to WEP. Unfortunately, some of the networks I need to connect to are WEP encrypted, therefore this is a serious issue for me that is preventing me from using Ubuntu on my laptop. Any suggestions?

  Read the article

• Triple-head on a Lenovo T520

  - by codeape

  Lenovo T520 with integrated Intel HD graphics + a NVidia card (Optimus) Ubuntu 11.10 on the computer. I would like to use the built-in screen plus two external screens. This PDF indicates that it is possible to connect up to four external monitors to the laptop. The information is Windows only. I was planning to disable the NVidia card, since I have read that Linux support for Optimus is not good. Questions: Has anyone set up three monitors on NVidia hardware? Has anyone set up three monitors using Intel HD 3000? Can I expect it to work out of the box, or are there tricks I need to be aware of?

  Read the article

• Ubuntu Server 11.04 installs fine then gets stuck on USBHID

  - by SZetta

  ites! I have installed Server 11.04 many many times from this disc and they have always worked perfectly (installed and operated fine). I wanted to reinstall my server again on the same hardware so I threw the disc in and installed but once it finished installing the boot loader and ejected the disc, it decided to go unresponsive. I restarted it and it loaded in through the grub perfectly it seemed, but then it goes and says either that a ipv6 router is unavailable (even though I have it hardwired to my network) or it goes and says usbhid: USB HID core driver and goes unresponsive there. I am very confused as this never happened before from this install. I want to see if this is just me or what before I just go ahead and download the newest version of server. Any advice would be appreciated. Thanks

  Read the article

• GRUB2 prompt instead of BURG boot screen after mistake during BURG installation

  - by Tomas Lycken

  I just installed BURG, but during the installation I made a mistake: after the package was installed, I got to some command-line based GUI for configuration, where I forgot to mark my (only) hard disk as the boot device before I hit OK. I tried to reinstall (apt-get purge burg && apt-get autoremove followed by apt-get install burg) but I wasn't able to get to the same screen again (I didn't find the GUI). When I now start my computer, I am taken to a GRUB2 prompt and no BURG (or GRUB2) boot menu is shown. Since I don't know any GRUB commands and I am helpless. How do I reinstall GRUB/BURG correctly? Update: I rebooted my computer, and got a BURG prompt (which appears to be the same thing as a GRUB prompt, but if there's a difference I wouldn't know it...). I have booted from a Live USB, but I don't know what to do next. The text above has been updated to reflect this new situation - for the original text, please see the previous versions of this post. (No answers were posted when this was edited...)

  Read the article

• Ubuntu one, music streaming

  - by iknowshall

  I'm running Ubuntu 11.10, and just signed up for Ubuntu One and Ubuntu One Music. Generally file sync is working fine, but music has been a complete failure so far. Here's what I'm looking at: After 24 hours, not a single mp3 or ogg file from my laptop has sync'd to the Cloud Music folder. I have 4 gigs of data used, which is definitely not enough to include music files. That's about the right amount for my docs and photos. With music, it should be more like 13 gigs. No music shows up on the Ubuntu One Music app on my phone, nor on the web view of my Ubuntu One Cloud folder I followed all the online instructions I could find. Basically, on my laptop, right click on the Music folder and select "Ubuntu One Synchronize this folder" The Music folder now has a green check mark on it indicating its sync'd The Ubuntu One app on my laptop says "File Sync is up to date" I did provide credit card information, and on the Ubuntu One website "Music Streaming" is listed as one of my services. So what am I doing wrong? Just read this post as I'm experiencing the same problem, the answer for this post says that due to the large number of files trying to be uploaded, that it could take up to a week. However I am, as above also being told that "File sync is up to date" Can somebody confirm that this is a bug and that I just need to wait for File sync to actually be up to date? Cheers

  Read the article

• Bash prompt doesn't print until I interact with console again

  - by durron597

  I don't even know where to begin to diagnose this one. Usually, when a command finishes, the prompt prints itself for the next command. However, that is not happening. Hard to explain with words, I'll just use an example: User@Machine:~$ cp /mnt/mountname/directory/textfile.txt . After waiting several seconds (far too long for this operation on a small file) I press Enter, and see: User@Machine:~$ cp /mnt/mountname/directory/textfile.txt . User@Machine:~$ User@Machine:~$ So clearly the operation had finished, but the prompt didn't display... until I pressed enter, and then BOTH prompts instantly displayed. This error does not happen with commands like cd.

  Read the article

• How do you convert many files from .xlsx to .xls ?

  - by David Oneill

  What is a way to convert a batch of .xlsx files to .xls format? I would prefer it to be a command-line solution, but anything is better than opening each manually, and manually saving in the new format. ~~Edit~~ So is there a way to get around that error? errored: Leaking python objects bridged to UNO for reason pyuno runtime is not initialized, (the pyuno.bootstrap needs to be called before using any uno classes) python: tpp.c:63: __pthread_tpp_change_priority: Assertion `new_prio == -1 || (new_prio >= __sched_fifo_min_prio && new_prio <= __sched_fifo_max_prio)' failed. Aborted

  Read the article

• finding the gedit plugin folder

  - by BlackSheep

  I am a bit confused as to where I should put externally downloaded plugins. I have tried putting them in: /usr/share/gedit/plugins ~/.local/gedit/plugins ~/.gnome2/gedit/plugins /usr/lib/gedit/plugins The way I have checked whether the plugins show up or not is going to Edit-Preferences-Plugins and looking for the ones I have downloaded (clickconfig, gedit-developer-plugins-...). Since I do not see any new plugins appearing, I have to assume that I am doing something wrong. None of these have worked. I am a bit tired of polluting my system. It's probably my own fault as it's written somewhere I have not thought to look. Please let me know how to add external plugins to gedit properly. I am running Ubuntu 11.10. My gedit version is 3.2.3 EDIT: I am still not able to solve this problem. I have tried the following folder now as well, and it hasn't worked: ~/.config/gedit/plugins

  Read the article

• Conflict between variable substitution and CJK characters in BASH

  - by AndreasT

  I encountered a problem with variable substitution in the BASH shell. Say you define a variable a. Then the command $> echo ${a//[0-4]/} prints its value with all the numbers ranged between 0 and 4 removed: $> a="Hello1265-3World" $> echo ${a//[0-4]/} Hello65-World This seems to work just fine, but let's take a look at the next example: $> b="?1265-3?" $> echo ${b//[0-4]/} ?1265-3? Substitution did not take place: I assume that is because b contains CJK characters. This issue extends to all cases in which square brackets are involved. Surprisingly enough, variable substitution without square brackets works fine in both cases: $> a="Hello1265-3World" $> echo ${a//2/} Hello165-3World $> b="?1265-3?" $> echo ${b//2/} ?165-3? Is it a bug or am I missing something? I use Lubuntu 12.04, terminal is lxterminal and echo $BASH_VERSION returns 4.2.24(1)-release. EDIT: Andrew Johnson in his comment stated that with gnome-terminal 4.2.37(1)-release the command works fine. I wonder whether it is a problem of lxterminal or of its specific 4.2.24(1)-release version.

  Read the article

• Disk failing on dell mini, are there diagnostic tools?

  - by John Lawrence Aspden

  Hi, my dell mini 10v running Ubuntu 10.10 runs ok for hours, but then will suddenly slow down drastically. Switching to a console shows lots of error messages, which also get into /var/log/syslog. These errors happen every couple of seconds. I'm figuring that the disk is failing, but is there anyway to be sure, and can laptop disks be replaced easily? Mar 20 11:08:12 dell-mini kernel: [ 2476.378774] ata1.00: status: { DRDY ERR } Mar 20 11:08:12 dell-mini kernel: [ 2476.378785] ata1.00: error: { UNC } Mar 20 11:08:12 dell-mini kernel: [ 2476.449841] ata1.00: configured for UDMA/133 Mar 20 11:08:12 dell-mini kernel: [ 2476.449887] ata1: EH complete Mar 20 11:08:14 dell-mini kernel: [ 2478.777754] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Mar 20 11:08:14 dell-mini kernel: [ 2478.777976] ata1.00: BMDMA stat 0x24 Mar 20 11:08:14 dell-mini kernel: [ 2478.778059] ata1.00: failed command: READ DMA Mar 20 11:08:14 dell-mini kernel: [ 2478.778162] ata1.00: cmd c8/00:08:43:3b:97/00:00:00:00:00/e0 tag 0 dma 4096 in Mar 20 11:08:14 dell-mini kernel: [ 2478.778166] res 51/40:00:47:3b:97/00:00:00:00:00/00 Emask 0x9 (media error)

  Read the article

• Why is Gnome-Shell thinking my "d" key minimizes all windows?

  - by Limitless

  I am on Ubuntu 12.04 LTS (in gnome-shell) and I am unable to use my "d" key. Regular gnome-2 works perfectly fine, but for some reason I cannot use my "d" key in gnome-3. I recently installed it and have been trying to figure this out, but I have no clue what's going on. I attempted to disable the keyboard shortcut that minimizes active windows, but that did not work. (My only option right now is to use CTRL-V to paste my "d"s.) On top of this, my arrow keys automatically move my windows and I cannot move through text using them. What's going on here, folks?

  Read the article

• Why are some checkboxes in Software Updater disabled?

  - by Drew Noakes

  In Ubuntu 13.04, the Software Updater shows some apps as having updates, but they're non-selectable: It's not clear why they're greyed out. On the command line: $ sudo apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done The following packages have been kept back: gnuplot-nox gnuplot-x11 nvidia-current 0 upgraded, 0 newly installed, 0 to remove and 3 not upgraded. Note too that running apt-get dist-upgrade does not cause them to be installed either, as it sometimes does with packages that are kept back. Here's the output: $ sudo apt-get dist-upgrade Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... Done The following packages have been kept back: gnuplot-nox gnuplot-x11 nvidia-current 0 upgraded, 0 newly installed, 0 to remove and 3 not upgraded. I took @quidage's suggestion, which gives the following. However subsequent upgrades show the same message: $ sudo apt-get install -f Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 3 not upgraded.

  Read the article

< Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >