Search Results

Search found 10536 results on 422 pages for 'cpu usage'.

Page 153/422 | < Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >

• Why is my second monitor not working?

  - by StampedeXV

  Since I have my new computer, I have a very weird problem. Facts: New Computer: Motherboard: ASRock Z77 Pro 3 Graphics-card: Asus1GB D5 X EN GTX560 DCII OC/2DI R CPU: Intel i5-3570 Windows 7 64bit 500W beQuiet special edition (92% efficiency) 8GB 1333MHz DDR3 Corsair RAM (CL9) Scythe Mugen 2 2 magnetic HDDs + 1 SDD 1 DVD-R Old Computer: Motherboard: Asus P55 something Graphics-card: Asus1GB D5 X EN GTX560 DCII OC/2DI R CPU: Intel i7-870 Windows 7 64bit 550W Corsair 8GB 1333MHz DDR3 Corsair RAM (CL9) Scythe Mugen 3 2 magnetic HDDs + 1 SDD 1 DVD-R On the old computer it worked fine with two monitors. Moving to the new (I took the same Graphics-card) it only works with one. The weird thing I mentioned is: not matter which one. But if I put both there, only one is available. There is no reaction at the start (where normally (at least if I remember correctly) the monitor shortly went from "standby" to "on"). Windows does not recognize a second monitor in the Device Manager. I have the latest drivers for Motherboard and Graphics-card. I have the latest BIOS drivers. I am out of ideas. Edit: completed computer setup

  Read the article

• How does it hurt to use Linux (Ubuntu) as a guest OS for all my tasks?

  - by sauparna

  I have a machine running Windows, where the disk has two partitions C (50 GB) and D (250GB). I do research in Information Retrieval and need to work with a large corpus (more than 50 GB) and in Linux. So if I want to install Linux on the existing system, keeping the Windows installation intact, will it be fine to run it in a virtual box? (say, QEMU, VMWare, etc.) An alternative is using Wubi. In that case the Linux installation has to be on drive C. Then, if I keep a small Linux installation (say 5GB) on C, and my corpus on D (mounted in Linux), how will it affect the performance of my programs which would be accessing the mounted Windows drive D. Is it feasible to use Linux this way? Which of the above is better if at all they are a way out? Note : Since my post in July 2010, I have been using and have tried several ways of maintaining a disk-image that I can mount in Linux. I had a 100GB qcow2 disk and a 100GB raw disk, both formatted to an EXT3 file system. I was mounting and connecting to the qcow2 disk using qemu-nbd. The problem was that every now and then, the connection to the disk would get lost and the running programs would throw disk I/O errors. The raw disk would mount and work fine as a loop mounted device, but when writing data to it, the mount.ntfs program would hog the CPU and the process would take an enormous amount of time. I was in fact running make on a piece of software located on this raw disk, and after a point of time make was waiting while mount.ntfs would show 100% CPU usage.

  Read the article

• Mysterious Windows 7 slowdown problem

  - by cletus

  I have a fairly beefy machine: Intel Q9450 8GB DDR2800 (4x2) Intel X25-M G2 80GB SSD Several other hard drives Windows 7 Ultimate 64 In the last month I've gotten a mysterious slowdown problem. When I start my IDE (IntelliJ IDEA) it usually takes about 20 seconds on the SSD. If my machine has been on for a day or two (as far as I can tell this is the only pattern) and I try to start the IDE, it brings my machine to a halt. CPU usage goes up to 25% per core (so it's basically 100% usage) and it takes up to 5 minutes to start. Other things I've noticed: iTunes will start to skip and stutter (my music is running off a second hard drive). The only persistent things I'm running are: AVG Anti-Virus Spybot (the slowdown predates this) Hamachi and Murmur (again the slowdown predates this) Apple Airport Base Agent HP OfficeJet 8500 driver/manager The browser I use is Chrome. I can't think why that'd be relevant but it's always on so I thought I'd mention it. When this happens I can't see a reason for it in the process list. No CPU hogs. No spikes in IO activity that I can see. Basically I'm at a loss to explain it and need to reboot, at which point everything returns to normal (for awhile). FWIW the Intel SSD is about 75-80% full. I know being too full can really degrade performance. I don't believe that's the issue here. Does anyone have any ideas on what I can do to fix this or at least help find what's going wrong? This same machine (sans SSD) could run Win XP and stay up fine for a month or two.

  Read the article

• MySQL is killing the server IO.

  - by OneOfOne

  I manage a fairly large/busy vBulletin forums (running on gigenet cloud), the database is ~ 10 GB (~9 milion posts, ~60 queries per second), lately MySQL have been grinding the disk like there's no tomorrow according to iotop and slowing the site. The last idea I can think of is using replication, but I'm not sure how much that would help and worried about database sync. I'm out of ideas, any tips on how to improve the situation would be highly appreciated. Specs : Debian Lenny 64bit ~12Ghz (6 cores) CPU, 7520gb RAM, 160gb disk. Kernel : 2.6.32-4-amd64 mysqld Ver 5.1.54-0.dotdeb.0 for debian-linux-gnu on x86_64 ((Debian)) Other software: vBulletin 3.8.4 memcached 1.2.2 PHP 5.3.5-0.dotdeb.0 (fpm-fcgi) (built: Jan 7 2011 00:07:27) lighttpd/1.4.28 (ssl) - a light and fast webserver PHP and vBulletin are configured to use memcached. MySQL Settings : [mysqld] key_buffer = 128M max_allowed_packet = 16M thread_cache_size = 8 myisam-recover = BACKUP max_connections = 1024 query_cache_limit = 2M query_cache_size = 128M expire_logs_days = 10 max_binlog_size = 100M key_buffer_size = 128M join_buffer_size = 8M tmp_table_size = 16M max_heap_table_size = 16M table_cache = 96 Other : > vmstat procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 9 0 73140 36336 8968 1859160 0 0 42 15 3 2 6 1 89 5 > /etc/init.d/mysql status Threads: 49 Questions: 252139 Slow queries: 164 Opens: 53573 Flush tables: 1 Open tables: 337 Queries per second avg: 61.302. Edit Additional info.

  Read the article

• WMI Sensors monitoring

  - by DmitrySemenov

  Monitoring tool Paessler stopped to monitor WMI Windows Sensors Paessler is Updated to version 12.4.5.3165. (10/30/2012 1:44:11 PM) Paessler windows sensors (against windows server 2008 R2 web edition) stopped to work (no changes have been made on server that we monitor) with the message Connection could not be established (80070005: Access is denied - Host: 192.168.2.10, User: Administrator, Password: **, Domain: ntlmdomain:) (code: PE015) However if I go to Virtual machine used to run Paessler and the following cscript runs successfully: strComputer = "192.168.2.10" Set objSWbemLocator = CreateObject("WbemScripting.SWbemLocator") Set objSWbemServices = objSWbemLocator.ConnectServer _ (strComputer, "root\cimv2", _ "Administrator", "pass") Set colProcessList = objSWbemServices.ExecQuery( _ "Select * From Win32_Processor") For Each objProcess in colProcessList Wscript.Echo "Process Name: " & objProcess.Name Next I'm getting output C:\>cscript test.vbs Microsoft (R) Windows Script Host Version 5.8 Copyright (C) Microsoft Corporation. All rights reserved. Process Name: Intel(R) Xeon(R) CPU X5680 @ 3.33GHz Process Name: Intel(R) Xeon(R) CPU X5680 @ 3.33GHz So WMI works a. I gave Administrator credentials for Device to monitor in Paessler setting, the same I used in the script above b. I restarted windows server (broken sensors) - but this didn't help c. I restarted Paessler probe service - no effect any ideas?

  Read the article

• How important is dual-gigabit lan for a super user's home NAS?

  - by Andrew

  Long story short: I'm building my own home server based on Ubuntu with 4 drives in RAID 10. Its primary purpose will be NAS and backup. Would I be making a terrible mistake by building a NAS Server with a single Gigabit NIC? Long story long: I know the absolute max I can get out of a single Gigabit port is 125MB/s, and I want this NAS to be able to handle up to 6 computers accessing files simultaneously, with up to two of them streaming video. With Ubuntu NIC-bonding and the performance of RAID 10, I can theoretically double my throughput and achieve 250MB/s (ok, not really, but it would be faster). The drives have an average read throughput of 83.87MB/s according to Tom's Hardware. The unit itself will be based on the Chenbro ES34069-BK-180 case. With my current hardware choices, it'll have this motherboard with a Core i3 CPU and 8GB of RAM. Overkill, I know, but this server will be doing other things as well (like transcoding video). Unfortunately, the only Mini-ITX boards I can find with dual-gigabit and 6 SATA ports are Intel Atom-based, and I need more processing power than an Atom has to offer. I would love to find a board with 6 SATA ports and two Gigabit LAN ports that supports a Core i3 CPU. So far, my search has come up empty. Thus, my dilemma. Should I hold out for such a board, go with an Atom-based solution, or stick with my current single-gigabit configuration? I know there are consumer NAS units with just one gigabit interface (probably most of them), but I think I will demand a lot more from my server than the average home user. Any advice is appreciated. Thanks.

  Read the article

• Computer sponteously reboots when doing heavy file copy to/from disk

  - by Mark Hosang

  I've been fighting with this problem for the last 3 weeks where my machine will just instantly reboot. No BSOD, and when i checked the event log all that was reported was the generic "Kernal-power" error with the detailed information pointing to a hard crash. This is a machine that was working for 18 months before these crashes started happening. When they started happening is after I added 3 HDs in a RAID-5, upped the memory to 12gb, moved to a new house, added a SSD and added about 5 case fans. I have thus eliminated the RAID, and determined that the SSD was not the cause (because it was still crashing even though the ssd wasn't connected). I've run memtest several times over night with no memory problems showing up. I've run IntelBurnTest to max out the cpu to see if it was a heat issue and at full tilt after 20 min it was only at 85C and the machine didn't crash. I also took a look at the voltages during this test, with a screenshot at the bottom of this post I've ruled out a software issue by reinstalling windows 7 ultimate x64 a total of 5 times, but even during that the install it crashes. Happens sometime during file copying at the beginning, or during uncompressing files, or sometimes during running windows update. The only discernible pattern i can see is that it seems to crash when hard disks might be spinning up or when they are accessed heavily from large file transfers. My current guess is that it is probably an issue with the MB, PSU or the power coming through the outlet. Any suggestions of what i could try to troubleshoot or what may be wrong? Specs PSU: Seasonic M12 700w Mem: 12gb CPU: i7-920 with stock heatsink MB: Asus P6T HDs: 3 green WD and 1 Corsair force 3 120b with 1.3.3 firmware Running full tilt voltages Idling Voltages

  Read the article

• How to resolve virtual disk degraded in Windows Server 2012

  - by harrydev

  I am using the new Storage Spaces feature in Windows Server 2012. I have the following disks: FriendlyName CanPool OperationalStatus HealthStatus Usage Size ------------ ------- ----------------- ------------ ----- ---- PhysicalDisk2 False OK Healthy Auto-Select 2.73 TB PhysicalDisk3 False OK Healthy Auto-Select 2.73 TB PhysicalDisk4 False OK Healthy Auto-Select 2.73 TB PhysicalDisk5 False OK Healthy Auto-Select 2.73 TB There is also a separate OS disk. The above disks are part of a single storage pool: FriendlyName OperationalStatus HealthStatus IsPrimordial IsReadOnly ------------ ----------------- ------------ ------------ ---------- Pool OK Healthy False False Within this storage pool some virtual disks are defined, see below: FriendlyName ResiliencySettingNa OperationalStatus HealthStatus IsManualAttach Size me ------------ ------------------- ----------------- ------------ -------------- ---- Docs Mirror OK Healthy False 500 GB Data Mirror Degraded Warning False 500 GB Work Mirror Degraded Warning False 2 TB Now the virtual disks are all running normal 2-way mirror, but two of the virtual disks are degraded. This is probably because one of the physical disks was offline for a short period of time. However, now the virtual disk cannot be repaired, even though, all physical disks are healthy. There is plenty of available space in the storage pool. This I cannot understand so I was hoping for some help, on how to resolve this? Below I have listed the full output from the Get-VirtualDisk CmdLet for the "Work" disk: ObjectId : {XXXXXXXX} PassThroughClass : PassThroughIds : PassThroughNamespace : PassThroughServer : UniqueId : XXXXXXXX Access : Read/Write AllocatedSize : 412316860416 DetachedReason : None FootprintOnPool : 824633720832 FriendlyName : Work HealthStatus : Warning Interleave : 262144 IsDeduplicationEnabled : False IsEnclosureAware : False IsManualAttach : False IsSnapshot : False LogicalSectorSize : 512 Name : NameFormat : NumberOfAvailableCopies : 0 NumberOfColumns : 2 NumberOfDataCopies : 2 OperationalStatus : Degraded OtherOperationalStatusDescription : OtherUsageDescription : Disk for data being worked on (not backed up) ParityLayout : PhysicalDiskRedundancy : 1 PhysicalSectorSize : 4096 ProvisioningType : Thin RequestNoSinglePointOfFailure : True ResiliencySettingName : Mirror Size : 2199023255552 UniqueIdFormat : Vendor Specific UniqueIdFormatDescription : Usage : Other PSComputerName :

  Read the article

• Difference between CurrentClockSpeed and MaxClockSpeed

  - by Ben

  Rationale this belongs on ServerFault rather than StackOverflow - I already have my program which gets the value, I am querying the value returned and what it means. I have an in-house program which audits our company PCs, and one of the things it checks is the speed of the processor. To do this, it queries the Win32_Processor WMI class and gets the value of CurrentClockSpeed. We were playing with the data today and found an anomaly with some of the speeds being reported incorrectly (for example, CurrentClockSpeed said 1.0GHz, whereas the CPU name said Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz [Confirmed it is in fact 1.83GHz]). I did a bit of digging on the internet and found this blog post which might explain what is going on. My initial thought was that I could change the program to instead get the value for MaxClockSpeed instead of CurrentClockSpeed, but Microsoft's documentation doesn't clearly define what this will return. What I mean by that is will this return a value which is its actual maximum speed (say if it were overclocked) but which it would not normally be running at, or would it return what I expect, which is its maximum speed under normal (not overclocked) conditions?

  Read the article

• Debian x86_64 + Nginx + PHP5-FPM optimization

  - by Olal'a

  I used to have a VPS (512MB) from Linode and I was running nginx + php5-fpm (which comes with php5.3.3) on Debian Lenny (i686). The total memory usage was about 90-100MB. Now I have another VPS (different hosting company) and I also run nginx + php5-fpm on Debian Lenny (x86_64). The system is 64-bit, so the memory usage is higher now, about 210-230MB, which I think is too much. Here is my php5-fpm.conf: pm = dynamic pm.max_children = 5 pm.start_servers = 2 pm.min_spare_servers = 2 pm.max_spare_servers = 5 pm.max_requests = 300 That's what top command tells me: top - 15:36:58 up 3 days, 16:05, 1 user, load average: 0.00, 0.00, 0.00 Tasks: 209 total, 1 running, 208 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni, 99.9%id, 0.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 532288k total, 469628k used, 62660k free, 28760k buffers Swap: 1048568k total, 408k used, 1048160k free, 210060k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 22806 www-data 20 0 178m 67m 31m S 1 13.1 0:05.02 php5-fpm 8980 mysql 20 0 241m 55m 7384 S 0 10.6 2:42.42 mysqld 22807 www-data 20 0 162m 43m 22m S 0 8.3 0:04.84 php5-fpm 22808 www-data 20 0 160m 41m 23m S 0 8.0 0:04.68 php5-fpm 25102 www-data 20 0 151m 30m 21m S 0 5.9 0:00.80 php5-fpm 10849 root 20 0 44100 8352 1808 S 0 1.6 0:03.16 munin-node 22805 root 20 0 145m 4712 1472 S 0 0.9 0:00.16 php5-fpm 21859 root 20 0 66168 3248 2540 S 1 0.6 0:00.02 sshd 21863 root 20 0 66028 3188 2548 S 0 0.6 0:00.06 sshd 3956 www-data 20 0 31756 3052 928 S 0 0.6 0:06.42 nginx 3954 www-data 20 0 31712 3036 928 S 0 0.6 0:06.74 nginx 3951 www-data 20 0 31712 3008 928 S 0 0.6 0:06.42 nginx 3957 www-data 20 0 31688 2992 928 S 0 0.6 0:06.56 nginx 3950 www-data 20 0 31676 2980 928 S 0 0.6 0:06.72 nginx 3955 www-data 20 0 31552 2896 928 S 0 0.5 0:06.56 nginx 3953 www-data 20 0 31552 2888 928 S 0 0.5 0:06.42 nginx 3952 www-data 20 0 31544 2880 928 S 0 0.5 0:06.60 nginx So, the question is there any way to use less memory? Btw, I have 16 cores and it would be nice to make use of them...

  Read the article

• How to find out what is causing a slow down of the application on this server?

  - by Jan P.

  This is not the typical serverfault question, but I'm out of ideas and don't know where else to go. If there are better places to ask this, just point me there in the comments. Thanks. Situation We have this web application that uses Zend Framework, so runs in PHP on an Apache web server. We use MySQL for data storage and memcached for object caching. The application has a very unique usage and load pattern. It is a mobile web application where every full hour a cronjob looks through the database for users that have some information waiting or action to do and sends this information to a (external) notification server, that pushes these notifications to them. After the users get these notifications, the go to the app and use it, mostly for a very short time. An hour later, same thing happens. Problem In the last few weeks usage of the application really started to grow. In the last few days we encountered very high load and doubling of application response times during and after the sending of these notifications (so basically every hour). The server doesn't crash or stop responding to requests, it just gets slower and slower and often takes 20 minutes to recover - until the same thing starts again at the full hour. We have extensive monitoring in place (New Relic, collectd) but I can't figure out what's wrong; I can't find the bottlekneck. That's where you come in: Can you help me figure out what's wrong and maybe how to fix it? Additional information The server is a 16 core Intel Xeon (8 cores with hyperthreading, I think) and 12GB RAM running Ubuntu 10.04 (Linux 3.2.4-20120307 x86_64). Apache is 2.2.x and PHP is Version 5.3.2-1ubuntu4.11. If any configuration information would help analyze the problem, just comment and I will add it. Graphs info phpinfo() apc status memcache status collectd Processes CPU Apache Load MySQL Vmem Disk New Relic Application performance Server overview Processes Network Disks (Sorry the graphs are gifs and not the same time period, but I think the most important info is in there)

  Read the article

• ESXi 5 Guests will not boot

  - by Adrian

  I have a problem with Guests not booting under VMWare ESXi 5.0 on my IBM x3550M3 server. Note: Investigation eventually determined that problem was with the VMware client on a Lenovo Edge laptop, the only Windows box available in a Linux IT shop. vSphere Client v4 and v5 duplicated behavior on the Lenovo Edge. As indicated in the comment to the accepted answer, replacing the workstation with one using different video was the "fix" for this particular issue. The ESXi host boots just fine. The Client connects just fine. Guests can be configured but do not successfully boot. The initial guest memory consumption jumps up to 560MB and drops down to 40MB after a few seconds. Initial CPU usage is 1 full CPU (3000Ghz per the chart) and immediately drops downm to 29Mhz. Guests do not display any output in the Console tab but show a state of 'Powered On'. No errors in the Events tab. Switching Guest from BIOS to EFI makes no difference. VMs are listed as Version 7 and the behavior is duplicated across all availabled Guest OS flavors. Problem also duplicated when server is booted up in Legacy Only mode. Logs do not contain anything particularly suspicious. Edit: No firewalls, routers, or VLANs in between the client and server. Edit 2: We have tried to Boot Guest into BIOS screen at Next Boot checkbox in the Guest Setting. Was not successful. Edit 3: 500GB datastore with 1 40GB VM on it. Plenty of space. Edit 4: Guests copied from my old ESXi 4 server DO NOT boot on the ESXi 5 system. Initially it complains about too little Video RAM being configured for the default 2500x1600, but it still doesn't work properly even after I bump the Video RAM settings or switch it to Auto-Detect.

  Read the article

• mysql thread count

  - by Ryan M.

  We have a web application that uses apache and mysql. Generally (according to Munin) our MySQL thread count sits between 2 and 4 at all times. The other day, our server almost came to a halt. HTTP requests were slow or wouldn't go through at all, SSH would work, but would take 30+ seconds to register keystrokes, etc.. So we pull up Munin and the only thing that's out of normal boundaries is the Mysql thread count. CPU usage was under 1%, load was under 1.0, plenty of available RAM. As mentioned before, the thread count floats around 2 to 4. At the time of our slow downs it had spiked to 14. So I start poking around the Internet and I see that in most cases, you'll start to see a higher thread count when you start running into slow queries. If I understand it correctly, the request comes in that takes a while to process, in the mean time other requests are coming in, so a new thread will be created to work on the request (yes?). But at the time of the slow down, we had 0 slow queries. My question is: What else can cause mysql to create additional threads. And would this sudden spike in threads possibly cause the server to slow down? To fix the issue, we restarted apache and everything went back to it's beautiful, normal self. Considering the the Server Vitals (CPU, RAM, Network, etc) were all ideal, and the thread count was the only thing out of place, this seems like the most logical thing to pursue as the possible cause. If it matters, we're on Mysql 5.1.40. Server is FreeBSD 7.2 and the server in question is inside a jail.

  Read the article

• VT-x not enabled on 2010 Mac Pro

  - by BlindingDawn

  To start I had a Hackintosh as per the instructions from Lifehacker.com before and moved everything to a new 2010 8 Core Mac Pro. I opted for a restore from the time machine backup rather than using the migration assistance. I believe this may have caused more problems but one in particular is the lack of VT-x support. When I checked Parallels Desktop under "Host Hardware" information, I get the following that shows that VT-x isn't enabled. <Cpu dyn_lists=""> <Number>16</Number> <Model>Intel(R) Xeon(R) CPU E5620 @ 2.40GHz</Model> <Mode>1</Mode> <Speed>2400</Speed> <VtxEnabled>0</VtxEnabled> <VtxMode>1</VtxMode> 1) Does Parallels Desktop support using VT-x? 2) Does this setting show that my VT-x isn't enabled? 3) Is there a way of fixing it so that it is enabled? 4) Is there a way of using my Time Machine backup as if I'm doing a restore using migration assistance and just restore the files and settings?

  Read the article

• MySQL getting stuck, eating up disk i/o

  - by bonez05

  Hi all, Using mySQL 5.0.51 on Solaris . At intermittent times it looks like MySQL is getting 'stuck' . The disk usage on the server spikes to 98% busy from reads. I used dtrace (specifically DTrace toolkit - iosnoop) to track down what processes was using all the reads. Mysql was calling tablename.TDM hundreds of times per second. There was no more than average load on the webserver that could account for this. There were no cronjobs running, and no other utilities like mysqldump or anything. It is a master / slave replication setup. As a jury-rigged fix, I altered the mysql table from 'tablename' to 'tablename2' and then back to 'tablename' This fixed the problem temporarily, and "unsticks" mysql. The disk usage goes back down and dtrace is no longer showing hundreds of reads to 'tablename.TDM' / second. A couple ideas I had are: 1. MySQL version bug 2. Infinite loop somewhere in my application (which i'm not sure how likely this is) 3. ?? Has anybody seen this before or have any insight? Thanks

  Read the article

• How to kill tasks in Windows 7 when even Task Manager won't open or respond?

  - by endolith

  Occasionally one of my computers will get so bogged down that everything locks up, Ctrl+Alt+Del doesn't work, Task Manager won't open, or they work, but are opening so slowly that it will take hours or days to shut down other processes and regain control of the computer, etc. Is there a way to, for instance, force Task Manager to be highest priority so it always opens immediately with Ctrl+Shift+Esc even when some other process/driver is hogging the CPU? Is there some other program that can run in the background and open immediately like this? This question isn't about fixing "underlying problems". No matter how much memory you have, it's still possible for a rogue process to eat it all up and lock up the computer in page fault thrashing, hog the CPU, etc. This question is about how to take back control of the computer when that happens. Basically when these kind of lock-ups happen, I want to open some kind of task manager that pauses every other process and allows me to kill one of them, and then let everything resume so I can save my work, etc. Otherwise my only option is to hold down the power button. Antifreeze is supposed to do exactly what i want, pausing all other applications and starting a task manager to kill the offender, but in my testing, it actually does neither.

  Read the article

• Monitoring AWS Systems Behind ElasticBeanStalk

  - by A. Avadis

  So I'm getting a company set up in the Amazon Cloud -- creating IAAS protocol/solutions/standardized implementation, etc while also being the SysAdmin for individual systems, app environments, and day-to-day uptime. One of the biggest issues I'm having is tracking various system/application logs, as well as logging/monitoring/archiving system metrics like memory usage, cpu usage, etc etc In a centralized fashion. E.g. -- Nagios + Urchin. The BIGGEST impediment to my endeavors is the following: The company application is deployed in the form of a Java *.WAR file, uploaded to an Elastic BeanStalk application environment, load balancing and auto-scaling between 3(min) and 10(max) servers, and the EC2's that run the application are fired up and disposed of ad-hoc. That is to say, I can't monitor the individual EC2's for very long because so many are being terminated then auto-provisioned/auto-scaled on the fly -- so I'd constantly be having to "monitor what I'm monitoring", and continuously remove/add EC2 machine addresses to my monitoring lists. IS there some sort of way to use monitoring tools like Zabbix or Nagios to monitor the ElasticBeanStalk, and have it automatically add on new EC2's, and remove terminated/failed EC2's from its monitoring list automatically? Furthermore, is there anything I can do with GrayLog to achieve similar results with the aggregation/centralization of my application logs from multiple EC2 instances into ONE consolidated set of logs/events? If not GrayLog, is there ANYTHING LIKE GrayLog that can automatically detect what EC2 members are being added/removed from the environment, and collect the logs from them automatically? Any and all advice or direction is appreciated. Thanks much, and cheers!!

  Read the article

• issues with Nginx + Passenger Production setup - Loading time/request time delay

  - by Dani Cela

  having a bit of an issue relating to request time. I have NGINX as a proxy server for a ruby on rails app running passenger. I also have a postgresql database server which is running on its own VM separate from my nginx/application server. My issue is that when I try and access my products page which does a lot of database queries, my query takes maybe 3-4 seconds. The second I flood the web server with requests, i will choke out the web server and have requests take almost 20-30 seconds to process. The rails server and database server do not crash, and the usage is not that high. Each server has more than enough memory, even cpu usage on the rails server isn't more than 85%, albeit thats high but its not maxing it out. Is my problem related to my nginx proxy server? I dont really know how to fully explain this so if you have a question please ask it and I can clarify what I mean. EDIT: to see exactly what i mean relating to the database query, see http://207.245.4.215/products

  Read the article

• Debian x86_64 + Nginx + PHP5-FPM optimization

  - by user55859

  I used to have a VPS (512MB) from Linode and I was running nginx + php5-fpm (which comes with php5.3.3) on Debian Lenny (i686). The total memory usage was about 90-100MB. Now I have another VPS (different hosting company) and I also run nginx + php5-fpm on Debian Lenny (x86_64). The system is 64-bit, so the memory usage is higher now, about 210-230MB, which I think is too much. Here is my php5-fpm.conf: pm = dynamic pm.max_children = 5 pm.start_servers = 2 pm.min_spare_servers = 2 pm.max_spare_servers = 5 pm.max_requests = 300 That's what top command tells me: top - 15:36:58 up 3 days, 16:05, 1 user, load average: 0.00, 0.00, 0.00 Tasks: 209 total, 1 running, 208 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni, 99.9%id, 0.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 532288k total, 469628k used, 62660k free, 28760k buffers Swap: 1048568k total, 408k used, 1048160k free, 210060k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 22806 www-data 20 0 178m 67m 31m S 1 13.1 0:05.02 php5-fpm 8980 mysql 20 0 241m 55m 7384 S 0 10.6 2:42.42 mysqld 22807 www-data 20 0 162m 43m 22m S 0 8.3 0:04.84 php5-fpm 22808 www-data 20 0 160m 41m 23m S 0 8.0 0:04.68 php5-fpm 25102 www-data 20 0 151m 30m 21m S 0 5.9 0:00.80 php5-fpm 10849 root 20 0 44100 8352 1808 S 0 1.6 0:03.16 munin-node 22805 root 20 0 145m 4712 1472 S 0 0.9 0:00.16 php5-fpm 21859 root 20 0 66168 3248 2540 S 1 0.6 0:00.02 sshd 21863 root 20 0 66028 3188 2548 S 0 0.6 0:00.06 sshd 3956 www-data 20 0 31756 3052 928 S 0 0.6 0:06.42 nginx 3954 www-data 20 0 31712 3036 928 S 0 0.6 0:06.74 nginx 3951 www-data 20 0 31712 3008 928 S 0 0.6 0:06.42 nginx 3957 www-data 20 0 31688 2992 928 S 0 0.6 0:06.56 nginx 3950 www-data 20 0 31676 2980 928 S 0 0.6 0:06.72 nginx 3955 www-data 20 0 31552 2896 928 S 0 0.5 0:06.56 nginx 3953 www-data 20 0 31552 2888 928 S 0 0.5 0:06.42 nginx 3952 www-data 20 0 31544 2880 928 S 0 0.5 0:06.60 nginx So, the question is there any way to use less memory? Btw, I have 16 cores and it would be nice to make use of them...

  Read the article

• Collect temperature and fan speed with munin from Windows 7 PC?

  - by nfm

  Hi, I'm quite fond of munin and using it also at home to monitor my PCs. What was super-duper easy under Linux is pretty much unsolvable for me under Windows: I'd like to monitor CPU and Motherboard temperatures as well as fan speed. On Linux I'm using lm-sensors and the plugin for munin was basically there. I access already some information from my Windows machine via SNMP (disk space, CPU usage, memory usage); the graphs are simple as is the information exposed via SNMP, but they do their job. But when it comes to temperature and fan speed I'm running against a wall. My research so far resulted in that Windows does not by default provide out of the box ability to retrieve temperature/fan speed data. Third party applications are necessary which have know-how how to communicate with the Motherboard chips. The best I cam up with is that SpeedFan exposes a shared memory interface and there exists a library which hooks into Windows SNMP facility and bridges over to SpeedFans shared memory interface; it's called SFSNMP (site currently down). Unfortunately the library doesn't work, there's a bug report at SpeedFan open about it, but it's currently not moving (although the SFSNMP author is active there) . So, unless that's going to work like anytime soon, are there any alternatives? I'm not found of buying any software to get that feature, given that I take it as granted that my system exposes me the information to properly monitor it, but anyway don't just not answer because of this.

  Read the article

• Poor performance on IIS7, only on Windows Server 2008, fine on Windows 7?

  - by user32005

  Hi, I'm new to IIS7 but have experience with other versions. I've been working on an application that works great in a dev environment (as always) but when I push it to a windows server 2008/IIS7 box performance takes a noticeable hit. The dev environment is Windows7/IIS7. The configuration in IIS is the same on the dev box as the server. I've tried all sorts of things to try and find a reason for this but I cant come to any conclusion. I've ruled out database problems on the live box as all data is cached after the first request. I've confirmed this to be true and made sure there is no additional database traffic. I've ruled out network issues with a combination of monitoring requests with fiddler and local debugging on the server. Whenever the code runs on the server there seems to be a performance issue. The server: Intel Core 2 Quad CPU Q6600 @ 2.40ghz with 2gb RAM. I know this is not fantastic but I was expecting it to at least perform as well as my dev environment (which is running much more on a lower spec). The CPU using peaks at under 60%, and memory usage is less than half of the available. I've enabled failed request tracing and most of the time is spent in a custom HttpModule, this module works to handle every request, I cant get any more detail as to what within the module may be causing the problem. Any ideas, I've been pulling my hair out for days now. Thanks

  Read the article

• Why is dwm.exe using so much memory?

  - by Leonard Challis

  I've scoured the web, but I'm sick of reading "scan your computer for viruses" and "upgrade your RAM" on answers to similar questions to this. I understand that dwm.exe is for (simply put) caching bitmaps for things like Aero-peek and similar, but as far as I have read it shouldn't be using vast amounts of memory. My colleague and I both have 4GB of RAM, Core 2 Duo, blah, blah -- essentially they're pretty capable. His dwm.exe is running at around 30mb, mind is currently running at about half a gig, though it does fluctuate quite a lot. This is the same while running the exact same applications (currently Zend studio, FireFox (with firemin - low memory usage), Outlook). Every so often I will get a notification asking me if I want to switch to Aero Basic because it's using too much memory, and sometimes it will just switch itself to basic and let me know why. I know it's possible to stop it switching, but I want to know why it is using too much memory otherwise it's just papering over the cracks. One thing to add is this seems to have started after a robbery on Monday, where two of my monitors were stolen, and I had to temporarily use a couple of alternative monitors. I am now using brand new monitors but the problem is the same. All drivers installed and working seemingly fine. Any ideas why the usage is so high? We are using windows 7 64-bit Professional.

  Read the article

• Window Server 2003 Print spooler

  - by mikenardone

  Hello Everyone in ServerFault, I am new to this website. I have been coming here to fix my own problems. I believe everyone here on this website is great. I could not find this issue anywhere. I am sure that other people had this issue. I have IBM X3850 48GB ram 2 TB of hard drives, four NIC cards. 2 Xeon 1.7 CPU. I am running VMware ESX. I believe that was the paid version if not then it is ESXI. I have 7 Servers on this server. All Window server 2003. On one of the Servers I keep on getting CPU is at 100% . So when I go into task manager and look at the processes that is going on, it is my print spooler. I have 30 different HP laserjet printers and two copiers from HP. I believe it is an driver issue, but I can't figure with one is doing this. Is there any programs for window server 2003 that finds bad print drivers.

  Read the article

• Windows Server 2008 R2 running at a snail's pace

  - by Django Reinhardt

  Really weird problem here. Our main web server has started running at a snail's pace, for absolutely no reason we can discern. Even after restarting the machine, when there's no little or no ram usage and CPU usage is fluctuating between 0 and 30%, simple tasks, like opening Internet Explorer, or waiting for My Computer to open, take forever. There are no processes hogging system resources that we can see... the machine itself is just exhibiting extremely slow behaviour. I've never seen a machine do this. A lot of security updates had built up, so we decided to let Windows install them. When we looked through the history upon restarting, though, they had failed with error code 800706BA. I don't know if this could be related or not. Any help in this matter would be greatly appreciated. As mentioned in the title, we're running a Windows Server 2008 R2 machine. It's also running SQL Server and IIS. It has 16GB of RAM and a decent Quad Core processor. It's also been fine until now -- and we haven't changed a thing. Thanks for any help.

  Read the article

• Having munin server monitoring problem: Graphs not being generated.

  - by geerlingguy

  When I run munin-cron (munin-cron --debug), I get the following error: 2010/05/10 13:39:01 [WARNING] Call to accept timed out. Remaining workers: archstl.org;archstl.archstl.org 2010/05/10 13:39:01 [DEBUG] Active workers: 1/8 These errors simply keep repeating themselves until I quit munin-cron. I've followed the directions for debugging munin on the 'Debugging Munin plugins' wiki page, but I get the following results when going through their directions: After telnetting to localhost 4949, I can see a list of plugins, see a node at archstl.archstl.org, but can't fetch anything. The output is as follows: >fetch cpu . However, on the same machine (which is both the node and the master munin server), I can run munin-run cpu, and it prints the results correctly to the command line, like so: user.value 100829130 nice.value 3479880 system.value 13969362 idle.value 664312639 iowait.value 12180168 irq.value 14242 softirq.value 199526 steal.value 0 Looking at the wiki page mentioned above, it looks like it might be a plugin environment problem, but I can't figure out how to fix/change this... If the plugin does run with munin-run but not through telnet, you probably have a PATH problem. Tip: Set env.PATH for the plugin in the plugin's environment file.

  Read the article

< Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >