Search Results

Search found 7082 results on 284 pages for 'trs 80'.

Page 153/284 | < Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >

• Access internal IP using public IP

  - by willvv

  Hi, I have a DSL modem with a public IP address (201.206.x.x), and I have a web server in my internal network (192.168.0.50). I set up the modem to forward requests to port 80 to my web server, so, if I access 201.206.x.x from outside my network, it shows my web page, the same happens if I access 192.168.0.50 from a computer inside my network. Now, the problem is when I try to access 201.206.x.x from my internal network, the browser tries to connect to the DSL modem configuration, instead of redirecting my request to my Web server. Which settings do I have to change in the modem to set up this redirection? Thanks!

  Read the article

• OS X Snow Leopard stops processing clicks from Wacom Intuous2

  - by antiver

  I'm using a Wacom Intuos2 graphics tablet in OS X Snow Leopard 10.6.2, which works great, 80% of the time. Every 20 minutes or so, OS X to just start ignoring input from the pen. More specifically, only the pen tip is ignored - the side buttons on the pen still work. Putting the Mac to sleep and waking it back up restores functionality to the pen tip. This is using both of the latest Wacom drivers claiming compatibility with Snow Leopard: versions 6.1.2-5 (Nov 25, 2009) and 6.1.3-3 (Jan 21, 2010). I have no experience with this tablet with other version of OS X / drivers. The tablet works 100% in Windows, which leads to blame either OS X or the OS X drivers.

  Read the article

• Roundcube access from outside local network

  - by Mike K

  I have setup hmailserver on a windows xp pro computer and everything is working great when it comes to getting it to send and receive email. Now here is where my problem comes in... I have setup roundcube using uniserver and everything works great internally. Now, what I am trying to do is to be able to access roundcube from the internet outside of the local network. I have opened up ports 80, 443, and the mysql port yet I am still unable to access this from outside of the network. The error message that I am getting is as followed: Forbidden You don't have permission to access /webmail/ on this server. Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request. I believe something needs to be edited in the apache config file. Any help would be greatly appreciated. I am hoping I dont need to run this on windows server but I'm kinda losing hope and thinking I will need to because I need IIS.

  Read the article

• Does the nginx “upstream” directive have a port setting?

  - by user55467

  moved from:http://stackoverflow.com/questions/3748517/does-nginx-upstream-has-a-port-setting I use upstream and proxy for load balancing. The directive proxy_pass http://upstream_name uses the default port, which is 80. However, if the upstream server does not listen on this port, then the request fails. How do I specify an alternate port? my configuration: http{ #... upstream myups{ server 192.168.1.100:6666; server 192.168.1.101:9999; } #.... server{ listen 81; #..... location ~ /myapp { proxy_pass http://myups:81/; } } nginx -t: [warn]: upstream "myups" may not have port 81 in /opt/nginx/conf/nginx.conf:78.

  Read the article

• apache2 force proxy for specific url on a subdomain

  - by Tony G.

  Hi, I have a site that has dynamic virtual subdomains using mod_rewrite, as defined like this: <VirtualHost *:80> ServerName example.com ServerAlias *.example.com DocumentRoot /var/www/example.com/www RewriteEngine on RewriteCond %{HTTP_HOST} ^[^.]+\.examle.com$ RewriteRule ^(.+) %{HTTP_HOST}$1 [C] RewriteRule ^([^.]+)\.example.com(.*) /var/www/example.com/$1$2 </VirtualHost> The problem is that I want a specific url, say subdomain.example.com/CONTROL/ to point back to www.example.com/ using a proxy (not url redirecting). I have tried adding: RewriteRule ^([^.]+)\.example.com/CONTROL(.*) /var/www/example.com/www$2 [P] But that didn't work. Any ideas?

  Read the article

• DNS entries issues

  - by Yaman

  I have some troubles with my DNS entries (or maybe my Apache conf). I have something like this : kira.mydomain.com A 123.45.67.89 youfood.mydomain.com CNAME kira.mydomain.com www.youfood.mydomain.com CNAME youfood.mydomain.com All's good when I check theses entries with nslookup. When I try going on http://www.youfood.mydomain.com, it work but not with http://youfood.mydomain.com ... Here my vhost : <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName youfood.mydomain.com ServerAlias www.youfood.mydomain.com DocumentRoot /home/ftp_youfood/www/trunk <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /home/ftp_youfood/www> Options FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> [...] </VirtualHost> Is there anything wrong ?

  Read the article

• ASUS P6X58D and 12 GB of RAM

  - by Hunter

  I just assembled my new PC and it screams, BUT it's only recognizing 8 GB of RAM in BIOS and OS rather than the installed 12 GB. In the BIOS the RAM was registering at 1066 MHz so I set it to 1600 MHz. I updated the BIOS to the latest non-beta release. http://www.asus.com/product.aspx?P_ID=wurRaDZ8lo4Ckukj OS: Windows 7 Ultimate 64-bit Motherboard: ASUS P6X58D Premium CPU: Intel Core i7 920 RAM: CORSAIR XMS3 12 GB (6 x 2 GB) 240-Pin DDR3 SDRAM DDR3 1600 HDD: Intel 80 GB SSD SATA II Power supply: Kingwin 1000 W Modular I've installed the Beta BIOS 0808 but no luck!

  Read the article

• Can snort output an alert for a portscan (sfPortscan) to syslog?

  - by Jamie McNaught

  I've been working on this for too long now. I'm sure the answer should be obvious, but... Snort manual: http://www.snort.org/assets/125/snort_manual-2_8_5_1.pdf lists two logging outputs on pg 39 (pg 40 according to Acrobat Reader) as: "Unified Output" and "Log File Output" which I am guessing the former refers to the "unified" output mode... which makes me think the answer is "No, snort cannot output alerts for detected portscans to syslog." Config file I've been using is: alert tcp any 80 -> any any (msg:"TestTestTest"; content: "testtesttest"; sid:123) preprocessor sfportscan: proto { all } \ memcap { 10000000 } \ scan_type { all } \ sense_level { high } \ logfile { pscan.log } (yes, very basic I know). A simple nmap triggers output to the pscan.log Can anyone confirm this? Or point out how I do this?

  Read the article

• NAT for Sprint Nexus S "Portable Wi-Fi hotspot"

  - by Jon Rodriguez

  I am on a 2010 Macbook Air connected to the web over wifi tethering on my Sprint Nexus S. I want to be able to host a few files using MAMP, but it seems that Sprint is running a NAT. When I query checkip.dyndns.org right now, it returns 68.27.228.75. However, trying to navigate to that IP fails (even though I do have MAMP's Apache running on port 80, as verified via loopback). When I whois 68.27.228.75, it appears to be a Sprint address, with NetName "SPRINTPCS" and OrgName "Sprint Nextel Corporation". So, is there some way I can circumvent Sprint's NAT to allow people to connect to my server that is running on a Nexus S Portable Wi-Fi hotspot?

  Read the article

• Fritz!Box IPv6-Address different than IPv6-Prefix

  - by kmindi

  In my Fritzbox it states the following: IPv6-Adresse: 2a02:8070:600::14b6:c7******, Gültigkeit: 100465/86065s IPv6-Präfix: 2a02:8070:62c:3200::/56, Gültigkeit: 100464/86064s I am not able to connect to IPv6 Addresses from computers configured by the fritzbox, because they get an address with prefix 2a02:8070:62c:3200::/56 but somehow the fritzbox does not route those addresses. Is this because the IPv6-Address is not in the prefix range? The address of the Fritzbox responds to pings, but my computers reached via various addresses from the prefix range do not (: PING 2a02:8070:62c:3200:28d****(2a02:8070:62c:3200:28d****) 32 data bytes From 2a02:8070:600:0:14b6*** icmp_seq=0 Destination unreachable: Administratively prohibited From 2a02:8070:600:0:14b6*** icmp_seq=1 Destination unreachable: Administratively prohibited From 2a02:8070:600:0:14b6*** icmp_seq=2 Destination unreachable: Administratively prohibited From 2a02:8070:600:0:14b6*** icmp_seq=3 Destination unreachable: Administratively prohibited blocked ping this is "view" from outside From inside the ping6 looks like this: traceroute -6 heise.de traceroute to heise.de (2a02:2e0:3fe:100::8), 30 hops max, 80 byte packets 1 fritz.box (2a02:8070:62c:3200:****) 0.787 ms 1.424 ms 1.702 ms 2 * * * ...... 30 * * *

  Read the article

• Apache gives empty reply

  - by Jorge Bernal

  It happens randomly, and only on moodle installations. Apache don't add a line in the logs when this happens, and I don't know where to look. koke@escher:~/Code/eboxhq/moodle[master]$ curl -I http://training.ebox-technologies.com/login/signup.php?course=WNA001 curl: (52) Empty reply from server koke@escher:~/Code/eboxhq/moodle[master]$ curl -I http://training.ebox-technologies.com/login/signup.php?course=WNA001 HTTP/1.1 200 OK The apache conf is quite straightforward and works perfectly in the other vhosts <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /srv/apache/training.ebox-technologies.com/htdocs ServerName training.eboxhq.com ErrorLog /var/log/apache2/training.ebox-technologies.com-error.log CustomLog /var/log/apache2/training.ebox-technologies.com-access.log combined <FilesMatch "\.(ico|gif|jpe?g|png|js|css)$"> ExpiresActive On ExpiresDefault "access plus 1 week" Header add Cache-Control public </FilesMatch> </VirtualHost> Using apache 2.2.9 php 5.2.6 and moodle 1.9.5+ (Build: 20090722) Any ideas welcome :)

  Read the article

• Network traffic is not being forwarded from a VM to the network using a bridged interface with Xen + libvirt

  - by foob

  I'm having trouble getting network access from a VM that I'm running using Xen and libvirt. I've been trying different things and reading similar posts online for a couple of days but I'm really stuck at this point. If anybody could offer some insight it would be much appreciated. I have a VM that I'm running on a host with a bridge set up as br0 and an interface eth0 on a 192.168.60.0/24 subnet. The networking portion of the libvirt configuration xml is: <interface type='bridge'> <mac address='ff:a0:d1:e5:07:de'/> <source bridge='br0'/> <script path='/etc/xen/scripts/vif-bridge'/> <model type='virtio' /> </interface> When I start the VM a vif6.0 interface is created on the host and the ifconfig output is: br0 Link encap:Ethernet HWaddr 00:A0:D1:C3:07:DE inet addr:192.168.60.33 Bcast:192.168.60.255 Mask:255.255.255.0 inet6 addr: fe80::2a0:d1ff:fee5:7de/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13 errors:0 dropped:0 overruns:0 frame:0 TX packets:40 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3570 (3.4 KiB) TX bytes:3508 (3.4 KiB) eth0 Link encap:Ethernet HWaddr 00:A0:D1:C3:07:DE inet6 addr: fe80::2a0:d1ff:fee5:7de/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:492 (492.0 b) Interrupt:19 Memory:fe8f0000-fe900000 vif6.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:6660 (6.5 KiB) TX bytes:468 (468.0 b) virbr0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) The 'brctl show' output seems to show the bridge being configured correctly: br0 8000.00a0d1e507de no eth0 vif6.0 The ifcfg-eth0 contents in the VM are: DEVICE=eth0 BOOTPROTO=static HWADDR=FF:A0:D1:E5:07:DE IPADDR=192.168.60.133 NETMASK=255.255.255.0 ONBOOT=yes and the output of ifconfig in the VM look like what I would expect: eth0 Link encap:Ethernet HWaddr FF:A0:D1:E5:07:DE inet addr:192.168.60.133 Bcast:192.168.60.255 Mask:255.255.255.0 inet6 addr: fe80::fda0:d1ff:fee5:7de/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:468 (468.0 b) TX bytes:7780 (7.5 KiB) but when I try to ssh or ping another computer I get 'no route to host.' Using tcpdump on the host system I tried to see if I could narrow down where the problem is: # tcpdump -vv -i vif6.0 tcpdump: WARNING: vif6.0: no IPv4 address assigned tcpdump: listening on vif6.0, link-type EN10MB (Ethernet), capture size 96 bytes 14:49:40.833997 arp who-has 192.168.60.35 tell 192.168.60.133 14:49:41.833314 arp who-has 192.168.60.35 tell 192.168.60.133 14:49:42.833309 arp who-has 192.168.60.35 tell 192.168.60.133 So the VM is sending out out an arp who-has packet when I try to ssh to 192.168.60.35. I think that this means the setup within the VM is ok and that this is an issue on the host system. If I run tcpdump with the interface of br0 then I don't see these arp packets. My thought here is that the packets are being blocked before going on to the bridge somehow. I tried adding an iptables rule to resolve this: -A FORWARD -m physdev --physdev-is-bridged -j ACCEPT but it didn't work. I also tried the following: /sbin/sysctl -w net.bridge.bridge-nf-call-ip6tables=0 /sbin/sysctl -w net.bridge.bridge-nf-call-iptables=0 /sbin/sysctl -w net.bridge.bridge-nf-call-arptables=0 /sbin/sysctl -w net.ipv4.ip_forward=1 which had no impact. Is it obvious to somebody who has more experience than me what I'm missing here? Should vif6.0 have the same MAC address is eth0 in the vm? Do I need more rules in my iptables? Thanks for any help!

  Read the article

• IPv6 local address in hosts file

  - by Dan

  I have set up a local domain on my Apache server. Then I added the following line in my /etc/hosts file ::1 exampledomain.local After I trying to navigate to it, (I tried Firefox and Chromium) I got a server not found error. Then I tried ping6 and it worked: dan@danny:~$ ping6 exampledomain.local PING exampledomain.local(exampledomain.local) 56 data bytes 64 bytes from exampledomain.local: icmp_seq=1 ttl=64 time=0.032 ms If I replace ::1 with 127.0.0.1 in my hosts file, it works fine. I'm not sure if this is relevant but this is my Virtual Host configuration in Apache2: <VirtualHost *:80> ServerAlias exampledomain.local DocumentRoot /home/dan/sites/exampledomain <Directory /home/dan/sites/exampledomain> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/exampledomain-error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel debug CustomLog ${APACHE_LOG_DIR}/exampledomain-access.log combined </VirtualHost> My question is: How can I make it work with the IPv6 address?

  Read the article

• Trouble with setting up Mac SSH with TP-LINK router

  - by arxanas

  I have a Mac running OS X 10.7.2, and a TP-Link TL-WR740N (whose control panel looks like this). Remote Login is on in the Mac's System Preferences, and port 22 is set to forward on the router. I can access my Mac as a web server using the external IP on port 80, which I have set up through the same port-forwarding mechanism provided by the router, but when I try to ssh server@external-ip, it just times out after a long while. (The same thing happens when I try vnc.) I can, however, ssh and vnc successfully into that computer while I'm on the same network when using its internal IP. Since ssh appears to work and port forwarding appears to work, I can't figure out what's causing the problem. Does anyone have any idea what might cause this?

  Read the article

• Is this normal? Multiple httpd process

  - by ilcreatore

  I'm testing a new Server. This isnt really a peak time for my server (2pm), but still its running a bit slow, I was checking the ESTABLISHED connections using the following command: # netstat -ntu | grep :80 | awk '{print $5}' | cut -d: -f1 | sort | uniq -c | sort -n http://i.stack.imgur.com/cZuvP.jpg My MaxClients are set to 50. So as you can see on the picture, only 10 people are eating most of my ram. I got a server with 4GB Ram (2.7GB free for apache) but each apache process is eating 53MB each, wich mean im only allowed to accept 50 process. The KeepAlive = Off, but I notice those connections arent closing fast enough, is that normal?

  Read the article

• Apache KeepAlive in child location not working

  - by Mark Beaton

  I'm trying to turn keep-alive connections off for a requests to a child folder in Apache, but when I reload the config I get the following error: KeepAlive not allowed here Here's my vhost config: <VirtualHost *:80> ServerAdmin [email protected] ServerName example.com DocumentRoot /srv/www/mysite DirectoryIndex index.html <Location /subfolder> KeepAlive Off </Location> </VirtualHost> I've tried using <Directory> as well, but no go there either. Any ideas? I'd rather not turn keep-alive off for the whole site...

  Read the article

• Improving terminal server performance for a specfic app

  - by Matt

  We have a windows 2003 terminal server running 2X application load balancign that is hosting a client's application that is accessed by around 50 users. Each user has there own database. The database is a file based database. The application is developed under Delphi so I think the database may be BDE based. As you can imagine, there is probably quite a lot of disk i/o. Here are some of the perfmon settings. Logged in users (average) 20 - 25 CPU Utilization (average) 80 - 100% Disk Queue Length (average) 1.6 % Disk time (average) 111 Page faults/sec (average) 1400 The application takes on average about a minute to load up. As usual, the budget is tight. Is there basic windows performance tuning tips that people can recommend to improve things before we fork out on more RAM etc. Server is a 2.8GHz Xeon with 3GB of RAM.

  Read the article

• How do I configure multiple domain names on my IIS server?

  - by Dillie-O

  We have a few websites that we are running on one instance of IIS that need to be mapped for each of their domain names. For example. Site A has the domain name coolness.com Site B has the domain name 6to8Weeks.com Site C has the domain name PhatTech.com When I look at the "Web Site Identification" section of the IIS configuration window, I notice that I can specify an IP address and port, but if I click the Advanced button, I can also configure the site based on host header values as well. How do I configure each site in IIS? Ideally I would like them to all be able to listen to port 80, so I don't have weird URLs, but I'm not sure if I do this using headers, IP addresses, both, or something else.

  Read the article

• Windows Deployment Services

  - by timbrigham

  I have a slightly advanced Windows Deployment Services setup. My router hands out DHCP addresses, including the following config. ip dhcp pool Servers_100 network 192.168.100.0 255.255.255.0 bootfile boot\\x86\\pxelinux.0 next-server 192.168.100.50 default-router 192.168.100.1 dns-server 192.168.100.80 192.168.100.81 This works perfectly for other subnets - I have a couple screens in my pxelinux that allow me to select my various Linux installers or enter the windows preboot environment. For some reason I'm only receiving the default bootfile that opens to the windows preboot environment. Any idea why?

  Read the article

• Munin "Disk usage" is too high?

  - by f-aminov

  I've recently installed munin on my VMware client server and saw that the Disk usage shows about 80-90%. Everything else (cpu load, ram, etc.) seems to be running fine. I have only two virtual hosts on my server with 1000 users/day in total, so I don't think that's too much. Here is the graph for the disk usage. Server info: Debian Lenny, CPU 510Mhz, RAM 512MB Is it bad? What could possibly cause this? Thank you for any suggestions.

  Read the article

• redirect to 404 wildcard subdomain

  - by Leandro Garcia

  I setup a wildcard A record on my domain registrar. Now if a user access a missing subdomain on my domain, they will be redirected to the homepage. Currently my initial setup was this: <VirtualHost *:80> ServerAdmin webmaster@localhost RewriteEngine On RewriteRule ^(.*)$ http://domain.com$1 [R] DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> # more below... </VirtualHost> Any wildcard subdomain or if my IP is entered via URL will redirect to the homepage. Can I do something about this that will redirect (HTTP redirect perhaps) the wildcard subdomains to 404 page instead of to homepage?

  Read the article

• Why is my IMAP port not showing as open ( yet it works? )

  - by Leo

  Ive recently setup Postfix and Dovecot IMAP on a Debian Lenny box. Sending to this domain works fine and reading the email via IMAP works fine too. I'm curious though as to why when running nmap, port 10143 is not shown as open. nmap -sS -O 127.0.0.1 Starting Nmap 4.62 ( http://nmap.org ) at 2011-11-26 21:30 GMT Interesting ports on localhost.localdomain (127.0.0.1): Not shown: 1711 closed ports PORT STATE SERVICE 22/tcp open ssh 25/tcp open smtp 80/tcp open http 3306/tcp open mysql Am I missing something with NMAP? Thanks Leo

  Read the article

• Mac Websharing Off but Process Running

  - by benedict_w

  I have my mac setup to use php / mysql / apache via macports. Recently it has gone a bit pear shaped: it seems that the local mac versions of apache and mysql are running blocking the macports services: (48)Address already in use: make_sock: could not bind to address [::]:80 (48)Address already in use: make_sock: could not bind to address [::]:443 Web sharing in System preferences is off - How can I properly disable it? I tried turning it on an off again in System Preferences but it would not changed from off to on. Also if I kill the process it starts running again.

  Read the article

• Virtual host “Forbidden You don't have permission to access / on this server” on debian

  - by ulduz114

  Before I created a virtual host I could see "http://localhost", but when I created a virtual host I could not see "http://localhost" and my virtual host "http://test" Here is my virtualhost config file: <VirtualHost test:80> ServerAdmin [email protected] ServerName test ServerAlias test DocumentRoot "/home/javad/Public/test/public" <Directory "/home/javad/Public/test/public/" > Options Indexes FollowSymLinks MultiViews ExecCGI DirectoryIndex index.php AllowOverride all Order allow,deny allow from all </Directory> </VirtualHost> so I ran a2ensite test and added 127.0.0.1 test to /etc/hosts file and restart apapche2 fine But after that I cannot access to http://test or even http://localhost i get Forbidden You don't have permission to access / on this server. When I delete my virtual host setting I can access http://localhost

  Read the article

• nginx static files caching doesn't work

  - by user74344

  here is my conf file: usr/local/nginx/sites-available/default server { listen 80; server_name localhost; location / { root html; index index.php index.html index.htm; } # redirect server error pages to the static page /50x.html error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } # serve static files directly location ~* ^.+.(jpg|jpeg|gif|css|png|js|ico|swf)$ { expires 30d; } but it doesn't cache static files, how should I fix it? thanks a lot

  Read the article

< Previous Page | 149 150 151 152 153 154 155 156 157 158 159 160  | Next Page >