Search Results

Search found 5749 results on 230 pages for 'miles away'.

Page 154/230 | < Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >

  • Static Network configuration with bridge in CentOS 6.2

    - by Kyle
    I have a server with CentOS 6.2 installed, I want to use it as a VM host to run some windows installations for development purposes. I wanted to be able to directly RDP and serve websites from IIS on these windows server installations, so I figured I would set it up as bridged networking. I have been struggling with this all morning, usually the result being that when I brought up the bridge interface all network connectivity to the CentOS would go away, however, I think I finally have that all figured out. However, here's what happens. The eth0 and br0 interfaces are defined in /etc/sysconfig/network-scripts with ifcfg-eth0 and ifcfg-br0. I DO NOT have ifup or ifdown or any other files for these interfaces, I have not found if they are needed. I can login and use firefox to browse the web, however, running ifconfig reveals that my eth0 does not have an IPAddress, but the br0 does. I can actually RDP into the Windows installation, and browse the internet from there as well, but I cannot directly connect(via putty, vnc, nor viewing web pages) to the CentOS box. Any idea what's up? ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none IPADDR=192.168.1.20 GATEWAY=192.168.1.1 NETMASK=255.255.255.0 NETWORK=192.168.1.0 ONBOOT=yes BRIDGE=br0 ifcfg-br0 DEVICE=br0 TYPE=Bridge BOOTPROTO=static DNS1=192.168.1.1 DNS2=8.8.8.8 GATEWAY=192.168.1.1 IPADDR=192.168.1.2 NETMAS=255.255.255.0 ONBOOT=yes I know some of the options are inconsistent (DNS and BOOTPROTO) because I tried changing those in the eth0 file to make it work, and the changes haven't adversly affected web browsing or the other functionality Thank you!

    Read the article

  • User directive in nginx generates error despite running as UID root

    - by Joost Schuur
    I'm running nginx on a MacOS X machine, installed with brew, and when I launch nginx, even with sudo, I get the following warning in my log file over and over again: 4/21/11 2:03:42 AM org.nginx[3788] nginx: [warn] the "user" directive makes sense only if the master process runs with super-user privileges, ignored in /usr/local/etc/nginx/conf/nginx.conf:2 From nginx.conf: user jschuur staff; I'm already launching nginx with sudo, since I want the thing to listen on port 80. Shouldn't that be enough to give it the proper super user privileges? The nginx binary as it's installed: jschuur@Glenna:sbin ? master ls -la total 4544 drwxr-xr-x 3 jschuur staff 102 Apr 12 20:53 . drwxrwxr-x 15 jschuur staff 510 Apr 12 15:25 .. -rwxr-xr-x 1 jschuur staff 2325648 Apr 12 20:39 nginx FWIW, I recompiled the binary to set passenger up and moved it around from it's original location into /usr/local/sbin. Update: As it turns out MacOS X was restarting nginx after I'd stopped it, because the launchd plist in ~/Library/LaunchAgents had set it to 'KeepAlive'. However, because I installed this plist into my local user's LaunchAgents folder as opposed to /Library/LaunchAgents (or better yet /Library/LaunchDaemons, which run before you even log on), it wasn't executed as root. Because of an error about not having permissions to use port 80, it actually exited right away, but still wrote to the same log file as the nginx process I started with sudo. I had thought the errors stemming from the automatic restart were actually coming from my manual restart via sudo. So, bottom line, problem solved. The real problem here was the homebrew instructions specifically asking you to install the plist file into an area that wouldn't allow a local site to use port 80.

    Read the article

  • Sonicwall TZ210 - Set up public wifi on separate subnet & interface

    - by thomasjbarrett
    I want to set up a public wifi by connecting another router to the X6 interface, and put it on a separate subnet (192.168.10.0/24) & in the DMZ Zone to keep it away from the regular LAN. I believe I have the network settings correct: the router has acquired the IP and DNS information from the TZ210, and the TZ210 shows it as an active DHCP lease. X6 is in the DMZ. I now have a routing/NAT/firewall problem, since I can't get any traffic to travel from the subnet to the internet. I can't get to any external websites and can't ping the TZ210 from the subnet. X0 is the regular LAN, and X1 is the WAN. Looking for any tips or tutorials on this. Here's my current relevant rules: Routing Source: X6 Subnet Destination: Any Service: Any Gateway: Default Gateway Interface: X6 Source: Any Destination: X6 Subnet Service: Any Gateway: 0.0.0.0 Interface: X6 NAT Policies Source Original: Any Translated: WAN IP Destination Original: Any Translated: Original Inbound: X6 Outbound: X1 Source Original: Any Translated: U0 IP Destination Original: Any Translated: Original Inbound: X6 Outbound: U0 Firewall DMZ LAN : Deny All DMZ WAN : Allow All LAN DMZ : Allow All WAN DMZ : Allow All

    Read the article

  • Very uneven CPU utilization with SQL Server 2012 on 2 processor computer with 16 cores / processor

    - by cooplarsh
    After installing SQL Server Enterprise 2012 with the Server + Cal license model, on a computer with 2 processors each with 16 cores (and no hyperthreading involved) and putting the server under extremely heavy load the 16 cores on the first processor were very underutilized, the first 4 cores on the 2nd CPU were heavily utilized, and the last 12 cores were not used at all (because of the 20 core limit for this sql server version). Total CPU utilization was displaying as around 25%. Unfortunately, the server suffered from extremely poor performance even though if the tasks were evenly distributed across the 20 cores it wouldn't have been anywhere near as bad. The Windows Server was running on a VMWare virtual image under ESX Server, but all of the CPU was allocated to the windows server. We tried changing affinity settings (e.g., allocating most cores to CPU and the others to I/O), but that didn't help solve the performance problems. Upgrading the product edition to SQL Server Enterprise Core 2012 not only allowed the SQL Server to utilize the 12 previously unused cores on the 2nd processor, but it also resulted in a much more even distribution of tasks across all of the processors. To get through the backlog of requests cpU utilization jumped to around 90%, and then came down to around 33% once it was caught up, but performance improved dramatically since we failed over to the newly updated version And the performance issues went away. I was wondering if anyone knows what might cause SQL Server to unevenly distribute the load, relying almost exclusively on the first 4 cores of the 2nd processor that had 12 cores idle, and allocate only a few tasks to each of the 16 cores on the first processor. Also, is there any way we could have more evenly distributed the load across the 20 cores that were being used without the product edition upgrade? The flip side of that question is what did the product upgrade do that caused SQL Server to start evenly distributing the load across all of the cores that it recognized? Thanks to any insight to answer these questions and/or links that might help me better understand how to make sense of what was happenings.

    Read the article

  • ajax.googleapis.com stopping my Firefox

    - by Oscar Reyes
    Today for some strange reason, Firefox stops working properly because it is trying to fetch something from ajax.googleapis.com. Is there something I can do to avoid this? Safari and Chrome work just fine. I tried uninstalling Firebug and clearing the cache. The only thing that worked was disabling the JavaScript altogether. This seems to be the culprit link: http://ajax.googleapis.com/ajax/libs/jquery/1.3.2/jquery.min.js What can I do? EDIT I think I have found where the problem is. My proxy is serving one byte at a time the file, so firefox consume it at that peace. What I don't understand is why Safari and Chrome takes it right away. What I did last night was, leave the FF open all the night to give him change to load the file, my hope was that I got cached and the next time there was no need to go for it. Today in the morning, the page load successfully but the page was not cached, because the next request failed the same. Here's a video showing the problem:

    Read the article

  • subdomain .htaccess redirection via ssh remote port forwarding

    - by Achim
    I ask you to help me URL redirecting a subdomain to a SSH remote forwarded port: The current setup is the following: The server A have a local webserver running on port 80. This server is connected to a DSL line or a GPRS connection where the IP address changes often. To prevent a DynDNS setup we established a SSH remote port forwarding to a server B with a static IP adress. This is done on server A by the following statement: ssh -N -p 80 -g -R 10000:localhost:80 tunneling@<Server B IP> So by accessing the new port 10000 of the servers B IP-adress, all traffic is forwarded to the server A port 80 - this works fine! But to offer a more comfortable url to the user I want to hide the server B IP-adress and offer a subdomain. My domain provider allows to add subdomains and redirections to some other servers. In general, this works, I've tested this with different servers. But it don't work if the destination is the port forwarded port of server B. The initial redirection is done, the request is send to server A and the response are forwarded to server B and shown in the browser - fine. But then the URL within the browser is switched away from the subdomain to the IP:port of server B. So the user don't see the subdomain in the URL string of the browser anymore. I've tried this with my providers subdomain redirection, as well as .htaccess redirect, as well as META refresh, the problem always persist. Is there a parameter in the ssh reverse forwarding setup (I guess this is the place where the fix have to be) to keep the typed in subdomain URL and not show the IP. Thanks Achim

    Read the article

  • Identifying Hard Drive as performance bottleneck for desktop machines

    - by Programming Hero
    I'm working in a development team where we all use laptops so we can work in multiple locations. These laptops are proving notoriously slow for development work, but at a glance they all look to have the specification for a much faster experience: CPU - Intel Core 2 Duo T7500 Memory - 2GB of RAM We all experience the biggest delays when the hard-drives are being accessed, particularly when swap-files are being thrashed. After doing a little bit of profile, a colleague discovered that our HDDs are seeing Read/Write speeds of about 10MB/sec. This seems abnormally low and we believe it the cause of the problem. Sensibly (though somewhat annoyingly) our business wont blow money on faster drives just to see if it fixes the problem; we need to illustrate this is definitely the problem and that buying some solid-state drives will make it go away. I need some way of showing how 90% of the system resources aren't being used over the course of a day, and that whenever there is utilization, it's all in HDD reads or writes. Are there any tools I could use to provide this information? Does it seem likely the problem is going to be fixed by a faster drive? Should I be looking for alternatives?

    Read the article

  • is it good to have or difference between ADSL Modem+WiFi Router and Separate ADSL Modem & Wi-Fi Router?

    - by vikas devde
    I have ADSL2 Modem which I got from my service provider, now I want to setup wireless(Wi-Fi) in my home. I went to shop, where I came to know that there are routers which come up with modem also but they are priced lil higher than the only wi-fi routers. Now it is obvious that I should go for only wi-fi one, as I already have modem. My question is, is there any difference between ADSL+router and only router? I think if I use ADSL+router, the speed will increase lilbit, as modem does modulate and demodulate signals, and router also generates wireless signal, that is time to take conversions is doubled, and if I use ADSL+modem, it will directly convert the signals to wireless, and time will be saved, so the overall speed will increase lilbit. This is what my concept is(Which might be wrong). What do you guys would suggest me? should I take my current modem away and buy an ADSL+router or I should keep my modem and buy only wi-fi one. Please tell me the difference and suggest me which one I should go with, and also suggest me which company router I should go for.

    Read the article

  • Swap static public IPs without creating DNS conflicts?

    - by Jakobud
    Our ISP is Comcast and we have 5 static public IPs from them that we use for various services, including customers connecting to our network, VPN, web, DNS, etc... We need more IP addresses from Comcast. Unfortunately, Comcast is telling us that they can't just simply give us 5 more addresses. They only give static IP addresses in blocks of 1, 5 or 13. In order for us to get more static IPs, they have to take away our current 5 static IPs and give us 13 new ones. How do we make this transition without causing all sorts of DNS chaos? We run public DNS servers, so we can make the DNS changes ourselves, but it will take some time obviously for those DNS changes to propagate throughout the internet. Are there any easy ways to make this transition? Like create some type of fallback DNS entry or something? Surely there must be some sort of procedure for this kind of thing. The Comcast support guy was useless.

    Read the article

  • Using Windows Explorer, how to find file names starting with a dot (period), in 7 or Vista?

    - by Chris W. Rea
    I've got a MacBook laptop in the house, and when Mac OS X copies files over the network, it often brings along hidden "dot-files" with it. For instance, if I copy "SomeUtility.zip", there will also be copied a hidden ".SomeUtility.zip" file. I consider these OS X dot-files as useless turds of data as far as the rest of my network is concerned, and don't want to leave them on my Windows file server. Let's assume these dot-files will continue to happen. i.e. Think of the issue of getting OS X to stop creating those files, in the first place, to be another question altogether. Rather: How can I use Windows Explorer to find files that begin with a dot / period? I'd like to periodically search my file server and blow them away. I tried searching for files matching ".*" but that yielded – and not unexpectedly – all files and folders. Is there a way to enter more specific search criteria when searching in Windows Explorer? I'm referring to the search box that appears in the upper-right corner of an Explorer window. Please tell me there is a way to escape my query to do what I want? (Failing that, I know I can map a drive letter and drop into a cygwin prompt and use the UNIX 'find' command, but I'd prefer a shiny easy way.)

    Read the article

  • sudoer scheme for another web developer that retains my future control of a virtual server?

    - by Tchalvak
    Background: Virtual Private Server I have a virtual private server that I'm looking to host multiple websites on, and provide access to another web developer. I don't care about putting too many constraints on him, though I wouldn't mind isolating the site that he'll be developing from other sites on the server that I will develop. The problem: retain control Mainly what I want is to make sure that I retain control over the server in the future. I want to reserve the ability to create/promote/demote and other administrative functions that don't deal with web software. If I make him an admin, he can sudo su - and become root and remove root control from me, for example. I need him not to be able to: take away other admin permissions change the root password have control over other security/administrative functions I would like him to still be able to: install software (through apt-get) restart apache access mysql configure mysql/apache reboot edit web development configuration type files in /etc/ Other Standard Setups would be happily considered I've never really set up a good sudoers file, so simple example setups would be very useful, even if they're only somewhat similar to the settings that I'm hoping for above. Edit: I have not yet finalized permissions, standard, useful sudo setups are certainly an option, the lists above are more what I'm hoping I can do, I don't know that that setup can be done.

    Read the article

  • How do I create a "here document" within a shell function?

    - by BenU
    I'm working my way through William Shotts Jr.'s great The Linux Command Line on my Mac OSX 10.7.5 system. 90% of the linux that Shotts covers is close enough to Darwin that I can figure out or GTEM to figure out what's going on. I've made it to chapter 27 on "Writing Shell Scripts" and am getting hung up creating "here files" within a function. I get an syntax error: unexpected end of file error when I include the following function: report_uptime () { cat <<- _EOF_ <H2>System Uptime</H2> <PRE>$(uptime)</PRE> _EOF_ return } The error goes away if I use the following function placeholder: report_uptime () { return } Also, elsewhere in the script, outside of a function I use the cat << _EOF_ format to create a "here file" with no trouble: cat << _EOF_ <HTML> <HEAD> <TITLE>$TITLE</TITLE> </HEAD> <BODY> <H1>$TITLE</H1> <P>$TIME_STAMP</P> $(report_uptime) $(report_disk_space) $(report_home_space) </BODY> </HTML> _EOF_ If anyone has any idea what I'm doing wrong I would be grateful!

    Read the article

  • What command should be used to connect via SSH through squid proxy?

    - by Raul Cardoso
    I have set up a Squid HTTP Proxy (in centOS) and intended to use it also for ssh connections. Managed to configure putty (in a windows client) to use this proxy while connecting by ssh. Confirmed in the "target host" that the ssh connection was coming from Proxy server ip instead of the windows client IP. Used: targethost: 22 for ssh proxyserv: 3128 for proxy (along with proxy credentials) I'm now having problems connecting to the "target host" using Ubuntu and the same proxy server. I have tried the following: me@mycomp:~$ connect-proxy -H test@proxyserv:3128 targethost 22 Enter proxy authentication password for test@proxyserv: SSH-2.0-OpenSSH_6.2p2 Ubuntu-6 It hangs in last line, expecting some input. All attempts resulted in a "Protocol mismatch." error. Putty successfully connects to the http proxy and sends credentials, showing me ssh login right away. - How to do (with commands in Ubuntu) the same putty does? - Is there any other way than connect-proxy command to do this? Edit: Also tried the following with same result ("Protocol mismatch") me@mycomp:~$ connect-proxy -H test@proxyserv:3128 targethost 22 ssh -l myshel_login Thanks in advance Edit: Solution details (thanks to NickW pointing the right way) installed corkscrew and added to ssh_config Host targethost ProxyCommand corkscrew proxyserv 3128 %h %p /etc/ssh/proxypass created proxypass file login:password Restarted ssh and used a simple ssh command ssh mylogin@targethost (ssh password was asked as usual)

    Read the article

  • SQL Server 2008 second instance times out when logging in -- but only the first time?

    - by Kromey
    This is a strange one that has plagued me for a while now. When logging in to the second instance of SQL Server 2008 on one of our database servers, we get a timeout error: Cannot connect to servername\mssqlserver2. Additional information: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. (Microsoft SQL Server)") (This is the error message when trying to connect with Microsoft SQL Server Management Studio; other tools experience the same error, but of course say it in different ways.) Immediately re-attempting to log in works just fine, so whatever the cause it's ephemeral! This happens regardless of user or authentication type (both Windows and SQL Server authentication methods are supported on this instance). What's even weirder, though, is that the first instance on this server has never once demonstrated this problem. Server is a Windows Server 2008 R2 virtual server, hosted in Microsoft Hyper-V (host is likewise Server 2008 R2). The server has 2GB of RAM, and seems to regularly be using 90% of that -- could low memory be the cause of this issue? I could see this second instance -- which is not used very often yet -- being swapped out to disk, and then taking too long to load back into memory to respond in time to the connection request, but I'd rather have more than just my own hunch before I go scheduling a downtime for this server (the first instance is used regularly) and then just throwing extra resources at it in the blind hope that the problem goes away.

    Read the article

  • SCCM 2012 Clients no longer detecting

    - by user3685428
    Here is the scenario I had a fully functioning SCCM 2012 site server with the DP, MP, SUP, Application catalog, etc. roles configured and working. There is only one server on this site. Everything was great but i was not happy with SUP, so i decided to create a separate WSUS server and configure Windows Updates through GPOs. That setup worked great as well so i went ahead and removed the SUP role from SCCM and removed the WSUS feature from my SCCM server (they were configured on the same SCCM Server). I did not notice any problems right away. A couple days later i noticed that the OSD deployments were giving errors, and after a couple hours of trying suggestions from Google, i was able to uninstall PXE and make a few changes and reinstall with WDS to get it working again. Again, thought everything was fine and continued on. The last couple days i have noticed that any new machine deployed or installing the Client will show in the SCCM console as "No" Client. The client machines will show connected to a site but the software center shows "IT Organization" instead of our site like the previous clients. The existing clients all seem to be functioning normally. they still receive application distributions and configuration baselines, etc. Reinstalling, uninstalling and reinstalling, repairing does not fix the problems and this happens on all new clients. ClientLocation.log shows it connecting to the correct MP. Nothing odd in any of the logs except for the ClientMessaging.log which repeats continuously this line: <![LOG[Raising event: instance of CCM_CcmHttp_Status { ClientID = "GUID:0450fde3-ab82-41bf-9c33-87a18113744b"; DateTime = "20140528214824.993000+000"; HostName = "SOUNDWAVE.domain.org"; HRESULT = "0x00000000"; ProcessID = 4092; StatusCode = 0; ThreadID = 3720; }; ]LOG]!><time="16:48:24.994+300" date="05-28-2014" component="CcmMessaging" context="" type="1" thread="3720" file="event.cpp:706"> thanks

    Read the article

  • Chrome browser completely messing with network?

    - by kiasecto
    I have a bizare problem with Google Chrome on a intel core i5 running windows 7 32bit. Whenever chrome is installed, access to other computers in the home group becomes really slow - such as opening shares. Its becomes really slow to resolve windows names. Something goes hay-wire with the local network - pining local machines which is usually 0mS pings I get random timeouts and random successes. Whenever I try to load a local address inside of chrome (including localhost, 192.168.0.1 etc) - it always says something in the status bar about resolving proxy and times out after about 5 seconds, then seems to work fine. If I go to settings inside of chrome, it just brings up the internet explorer connection settings, where I have not set any proxy settings. One I uninstall chrome, all these problems go away. Network shares and name resolvings work instantly, pings to any machines never have a problem. Localhost and other network IP address work fine in all other browsers. Anyone heard of this problem before and know what it might be? I even tried re-installing winodws 7 and the problem came straight back when chrome was loaded on again.

    Read the article

  • Should be simple: existing laptop with local user and outlook 2007 migrate on same computer to domain user with outlook 2007 emails intact

    - by bifpowell
    I have Dell Laptop with windows 7 64 bit and for the last year it's been just a machine with an account like: machine\john there are files in folders and stuff in c:\users\john and john uses outlook 2007 as a pop3 client and has identifiable local appdata pst files. Now I installed a server and want to have everything be domain-centric so I added this laptop to the domain with admin credentials and then logged in as a domain user as: domain\john.smith Now I want to duplicate machine\john (outlook emails mostly) to domain\john.smith. In the past I used the Files and Settings Xfer Wizard and done. I tried that here and it crunched away for a while, made the file, but the restore had no effect - it ran for a while, had a progress bar, but it's like nothing happened at all afterwards. I've rebooted the machine, logged in as domain administrator as the first user to log on after the restart and tried: c:\users\john xcopy c:\users\john c:\users\john.smith /V /C /F /H /K /Y /E ...and it copies some of it, but when it gets to c:\users\john.smith\appdata\local\application data it chokes "Access denied, unable to create directory" I also tried logging in as domain\john.smith and copying the entire directory that the PSTs are in from machine\john and a lot of the mail was there when I launched outlook after replacing the PSTs, but not all of them??? I got errors about files in use when doing this method, which I figure must be why not all the old emails are in the inbox?... There must be some extremely simple way to do what must be a very common requirement. Any guidance appreciated.

    Read the article

  • SELinux blocking Samba directory listing

    - by Sean M
    I am running Samba on a CentOS server, and I am experiencing a problem where it allows me to connect to the server and see a share, but shows the share as an empty directory. I find this behavior strange. Here is the stanza in my smb.conf for the given share: [seanm] path = /home/seanm writeable = yes valid users = seanm, root read only = No Here's what I see on the server side: [seanm@server ~]$ ls -l -rw-r--r-- 1 seanm seanm 40 Jan 4 13:45 pangram.txt And yet: [seanm@client ~]$ smbclient //server/seanm -U seanm -W WORKGROUP Enter seanm's password: Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.33-3.29.el5_5.1] smb: \> ls . D 0 Fri Jan 7 10:08:55 2011 .. D 0 Fri Jan 7 07:58:31 2011 58994 blocks of size 262144. 50356 blocks available This behavior is present on both a Windows client and a Linux client system. The behavior is present with the firewall on and with the firewall off, so it's not that. Neither /var/log/messages nor /var/log/secure have any complaints about Samba. I doubt that SELinux is a problem: just in case, here are the relevant settings. [root@server ~]# getsebool -a | grep samba samba_domain_controller --> off samba_enable_home_dirs --> on samba_export_all_ro --> off samba_export_all_rw --> off samba_share_fusefs --> off samba_share_nfs --> off use_samba_home_dirs --> on virt_use_samba --> off What am I doing wrong here, and what can I do to fix it? Edit: SELinux probably is the problem, judging by the fact that the issue goes away when I set SELinux to "permissive" or issue setsebool -P samba_export_all_rw on - both of which are unacceptable for production environments. What the heck kind of context does a directory need to have on it for Samba users to actually get files from it? I consider rolling your own rules and/or context to be deeply sub-optimal.

    Read the article

  • Alternative software for Pinnacle PCTV 100e

    - by Stijn Sanders
    I have a Pinnacle PCTV 100e external USB cable television receiver. I've been using Pinnacle's software that came with the card (TVCenter Pro) to record things at given times. Things I don't like is an extremely high CPU load, and that it doesn't seem to halt the screensaver from running when watching in full screen. Also, I was away the last two weeks, and the schedules went terribly bust. Some items were recorded hours before or after the actual scheduled time (and now I missed some shows), and some recurring schedules weren't converted into the next occurrence correctly! Is there good alternative software that would work with my PCTV 100e? (Preferalby cheap or free) I've tried VLC Player, which gets video, but no audio. I've tried MediaPortal, which crashes when trying to scan for channels. When I select a channel manually, the stored mpg has big errors in encoding and is also missing audio. There's VirtualDub, but that doesn't have ready-made scheduled-recording options. This I can conjure some scheduled scripts for, but I've noticed the sync gets awfully wrong after some time. I've tried Windows Media Center, but it doesn't seem to support the PCTV 100e.

    Read the article

  • How to bypass vpn talking to VMWare Guest?

    - by marc esher
    Greetings. Network/VPN n00b question here. I'm running VMWare Workstation with a Guest Windows 2003 Server. It has SQL Server 2000 installed. The sole purpose for this Guest is to house SQL Server... it needn't have internet access or access to any other resources on the network other than the host. When launch Check Point VPN software, the host routes through the company network before it connects to the guest ... i.e. it's no longer a direct connection. I assume this is just how things are supposed to work. However, what's happening is that the connection between my host and the SQL Server instance on the guest intermittently drops. It's not consistent, and some databases on the server will be responsive while others aren't. It appears that the databases with the most traffic on the guest (the ones I'm hitting with load tests) are the ones that become intermittently unresponsive. This problem only manifests when VPN is on; when it's off, I can pound away on this database with no troubles. Thanks for any advice!

    Read the article

  • How to tell which process is hogging my CPU when they don't add up to 100%?

    - by endolith
    Ubuntu's System Monitor applet shows 100% CPU usage continuously. If I click it, the resources tab shows it at 100% continuously, too. If I go to processes, though, to find out which process is the culprit, there is nothing above 10%. If I run top there is nothing above 10%. The individual processes do not add up to 100%. I try killing lots of processes, but the overall usage continues to be 100%. How can I find out what's hogging the CPU? This is an unusual situation on a computer I use daily, which is never anywhere near 100% CPU unless I'm doing something that requires it (like loading 32 Firefox tabs), after which it goes back to a normal idle level. It's not a new install or anything. There is no reason the processor should be maxed out. I'm not sure when it started or if I changed something that caused it to happen. Normally I would use top or System Monitor and find the process that had gone out of control, but I can't find anything with those tools this time. It persists after reboots and everything. And the processor is obviously hot, so it's not an erroneous reading. Update: I tried killing every process, one at a time, until the problem went away, and killing vino-server finally fixed it, even though that process never went above 5%. I had enabled Remote Desktop a few days ago (and have obviously now disabled it). But the question remains: How did a single process manage to use 100% CPU while top only showed that process at 5%? How do I identify culprits like this in the future? Looks like I'm not the only one who's had this problem: Still a problem in both jaunty & karmic. Interestingly, both System Monitor & htop do not show the sum of individual processes being anywhere near 100% cpu.

    Read the article

  • Reducing video mode switching during Linux boot

    - by Zack
    When I boot up my desktop computer, which only has Linux on it, the video mode and/or console font gets switched four times: When GRUB starts, it switches from 80x25 text to a graphical mode so it can draw a pretty background behind its menu; GRUB then goes back to 80x25 text after I pick something from the menu; When the KMS driver for my video card loads, it switches to a much higher-resolution text mode (I don't know if this is a hardware text mode or not); Finally X starts and it goes graphics and stays that way. I think this last switch does not change the resolution of the video mode, only the graphicalness. I'd like to get rid of as many of these mode switches as possible. Ideally, when GRUB takes over from the BIOS it would go directly to the same high-resolution text mode that the KMS driver selects, and the display would stay in that mode till X starts and brings up graphics. I am under the impression that this is possible by mucking with the kernel command line and/or the GRUB console module load parameters, but I don't know the details. GRUB 1.98+20100706, kernel 2.6.32.15 using Nouveau video drivers. Distro is Debian unstable. Please no answers that involve recompiling anything or cobbling together bleeding-edge kernel/driver combinations, I don't care enough about this to go to that much trouble. EDIT: Tobu suggests setting GRUB_GFXMODE to the full pixel resolution of the monitor, and GRUB_GFXPAYLOAD_LINUX=keep to avoid the mode switch after the menu goes away. This does part of what I want, but winds up being worse overall. There's no mode switch after the menu, but there's still a painfully-slow screen repaint (I should probably just give up on GRUB's gfxmode, it's waaaay too slow at 1920x1200). More seriously, there's now a double mode switch when nouveaufb loads, along with fun-looking error messages in dmesg [ 5.923798] [drm] nouveau 0000:02:00.0: allocated 1920x1200 fb: 0x40250000, bo ffff8801ba5f4600 [ 5.923802] fb: conflicting fb hw usage nouveaufb vs EFI VGA - removing generic driver [ 5.923821] [drm] nouveau 0000:02:00.0: PFIFO_INTR 0x00000010 - Ch 1 ("PFIFO_INTR" message repeats 400+ times) [ 5.925609] Console: switching to colour dummy device 80x25 [ 5.925802] Console: switching to colour frame buffer device 240x75

    Read the article

  • hosts.deny not blocking ip addresses

    - by Jamie
    I have the following in my /etc/hosts.deny file # # hosts.deny This file describes the names of the hosts which are # *not* allowed to use the local INET services, as decided # by the '/usr/sbin/tcpd' server. # # The portmap line is redundant, but it is left to remind you that # the new secure portmap uses hosts.deny and hosts.allow. In particular # you should know that NFS uses portmap! ALL:ALL and this in /etc/hosts.allow # # hosts.allow This file describes the names of the hosts which are # allowed to use the local INET services, as decided # by the '/usr/sbin/tcpd' server. # ALL:xx.xx.xx.xx , xx.xx.xxx.xx , xx.xx.xxx.xxx , xx.x.xxx.xxx , xx.xxx.xxx.xxx but i am still getting lots of these emails: Time: Thu Feb 10 13:39:55 2011 +0000 IP: 202.119.208.220 (CN/China/-) Failures: 5 (sshd) Interval: 300 seconds Blocked: Permanent Block Log entries: Feb 10 13:39:52 ds-103 sshd[12566]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12567]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12568]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:52 ds-103 sshd[12571]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root Feb 10 13:39:53 ds-103 sshd[12575]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=202.119.208.220 user=root whats worse is csf is trying to auto block these ip's when the attempt to get in but although it does put ip's in the csf.deny file they do not get blocked either So i am trying to block all ip's with /etc/hosts.deny and allow only the ip's i use with /etc/hosts.allow but so far it doesn't seem to work. right now i'm having to manually block each one with iptables, I would rather it automatically block the hackers in case I was away from a pc or asleep

    Read the article

  • How to recover the plesk database?

    - by Kau-Boy
    When I try to launch the Plesk administration page of you server I get the following error: ERROR: PleskMainDBException MySQL query failed: MySQL server has gone away The MySQL Server is working well. Although it seems that the plesk database is somehow corrupt and any action on this database results in a restart of the mysql process, so even queries to other databases on the same MySQL server will be lost. If I try to connect to the plesk database using phpMyAdmin, I can only see the number of tables, the database had originally. But I am not able to open the tables listing. As soon as I try it, the mysql process crashes again. Trying to connect to the database using ssh works. I can even run a SELECT statement against any table an get a result. I don't know if it is an plesk error or an error of the psa database or even the MySQL server. Can you give me any tips on how to recover the plesk system. Should I try to repair the Plesk installation before. And if so, how can I do it and will all my settings get lost doing it? EDIT: Trying to dump the database, I get the following error: mysqldump: Got error: 2013: Lost connection to MySQL server during query when using LOCK TABLES

    Read the article

  • MySQL Error: FUNCTION LEVENSHTEIN already exists

    - by kgrote
    I've got an ExpressionEngine database and I exported a couple of tables from it, then dropped those tables. When I try to re-import the tables in PHPMyAdmin, I get this error: SQL query: -- -- Database: `my_db` -- DELIMITER $$ -- -- Functions -- CREATE DEFINER=`my_username`@`%` FUNCTION `LEVENSHTEIN`(s1 VARCHAR(255), s2 VARCHAR(255)) RETURNS int(11) DETERMINISTIC BEGIN DECLARE s1_len, s2_len, i, j, c, c_temp, cost INT; DECLARE s1_char CHAR; DECLARE cv0, cv1 VARBINARY(256); SET s1_len = CHAR_LENGTH(s1), s2_len = CHAR_LENGTH(s2), cv1 = 0x00, j = 1, i = 1, c = 0; IF s1 = s2 THEN RETURN 0; ELSEIF s1_len = 0 THEN RETURN s2_len; ELSEIF s2_len = 0 THEN RETURN s1_len; ELSE WHILE j <= s2_len DO SET cv1 = CONCAT(cv1, UNHEX(HEX(j))), j = j + 1; END WHILE; WHILE i <= s1_len DO SET s1_char = SUBSTRING(s1, i, 1), c = i, cv0 = UNHEX(HEX(i)), j = 1; WHILE j <= s2_len DO SET c = c + 1; IF s1_char = SUBSTRING(s2, j, 1) THEN SET cost = 0; ELSE SET cost = 1; END IF; SET c_temp = CONV(HEX(SUBSTRING(cv1, j, 1)), 16, 10) + cost; IF c > c_temp THEN SET c = [...] MySQL said: Documentation #1304 - FUNCTION LEVENSHTEIN already exists I get this error even if I drop all tables from the DB and try to import anything. The only way I can get the error to go away is to totally delete the database and re-create it. What's causing that error and how can I stop it from happening?

    Read the article

< Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >