Search Results

Search found 17860 results on 715 pages for 'virtual pc'.

Page 154/715 | < Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >

  • Network drives don't get mapped and desktop redirection stops working when domain user becomes a member of the Local Administrator group on their PC

    - by Kim Jong-Un
    We have a Small Business Server 2003 domain controller with Windows 7 workstations joined to the domain. I noticed recently that, if I make a user a local administrator on his computer, his redirected desktop and mapped network drives do not connect at login (error on login that network drives inaccessible and desktop is blank). However, it is still possible for this user to browse to his home directory where his redirected folders are located- so he still has access to that location. Does anyone have any theories as to what is going on here?

    Read the article

  • PC boots on then off & 30 sec. later on again, it wiil shut off on itself mostly in idle or just unexpecticly

    - by Jody
    This problem started w/ my sons desktop, it would just shut off after a bit of work or stay on for a long time & to get it to unfreeze is to cold boot it, i put a new HDD in & I still have the same issue, RAM is good power supply fan is moving quite as well as all the rest of the fans it has stayed fairly dust free, i'm at a loss ,I have defaulted all the factory settings changed battery & ungraded to a new OS. I still have the same problem. the power light stays on after it has shut down & when upon starting it goes straight to safe mode option page, I start in last good config. reboots again takes 30 sec. to boot & will work again for a while, the only other thing I haven't tried was a graphic card replace, i'm onboard video now & have been.

    Read the article

  • PC wont boot with more than 1 stick of RAM.

    - by Aidan
    Hi Guys, I've got the following computer and I've just put in a new CPU QX9650 and I've run into this problem since making this hardware change. Whenever I put more than 1 of my 4 sticks of ram into my machine it wont load an OS. It'll go through the BIOS but BSOD on windows load. It also wont let me install an OS from disk or boot into Linux. I've ran memtest with all 4 sticks in and I get 10k+ errors on test5. Each stick of ram on it's own is fine and functions properly. I only have problems when all 4 sticks are in the machine at the same time. System specs.. CPU: QX9650 Mobo: Asus P5B 2104 BIOS RAM: 2xPC25400 DDR2 , 2xPC2 6400 both OCZ. Is the problem on my end or is the CPU faulty?

    Read the article

  • PC wont boot with more than 1 stick of RAM.

    - by Aidan
    Hi Guys, I've got the following computer and I've just put in a new CPU QX9650 and I've run into this problem since making this hardware change. Whenever I put more than 1 of my 4 sticks of ram into my machine it wont load an OS. It'll go through the BIOS but BSOD on windows load. It also wont let me install an OS from disk or boot into Linux. I've ran memtest with all 4 sticks in and I get 10k+ errors on test5. Each stick of ram on it's own is fine and functions properly. I only have problems when all 4 sticks are in the machine at the same time. System specs.. CPU: QX9650 Mobo: Asus P5B 2104 BIOS RAM: 2xPC25400 DDR2 , 2xPC2 6400 both OCZ. Is the problem on my end or is the CPU faulty?

    Read the article

  • Collect temperature and fan speed with munin from Windows 7 PC?

    - by nfm
    Hi, I'm quite fond of munin and using it also at home to monitor my PCs. What was super-duper easy under Linux is pretty much unsolvable for me under Windows: I'd like to monitor CPU and Motherboard temperatures as well as fan speed. On Linux I'm using lm-sensors and the plugin for munin was basically there. I access already some information from my Windows machine via SNMP (disk space, CPU usage, memory usage); the graphs are simple as is the information exposed via SNMP, but they do their job. But when it comes to temperature and fan speed I'm running against a wall. My research so far resulted in that Windows does not by default provide out of the box ability to retrieve temperature/fan speed data. Third party applications are necessary which have know-how how to communicate with the Motherboard chips. The best I cam up with is that SpeedFan exposes a shared memory interface and there exists a library which hooks into Windows SNMP facility and bridges over to SpeedFans shared memory interface; it's called SFSNMP (site currently down). Unfortunately the library doesn't work, there's a bug report at SpeedFan open about it, but it's currently not moving (although the SFSNMP author is active there) . So, unless that's going to work like anytime soon, are there any alternatives? I'm not found of buying any software to get that feature, given that I take it as granted that my system exposes me the information to properly monitor it, but anyway don't just not answer because of this.

    Read the article

  • How much power supply does a typical PC build need?

    - by Wesley
    I am building a system for a friend. The potential specs are like this so far: ASUS A8N-VM motherboard AMD Athlon 64 3200+ @ 2.0 GHz Any 7200RPM SATA HDD Palit GeForce 8800GT 512MB GDDR3 PCIe One DVD/CD combo drive Creative SB Live! 5.1 sound card I was wondering what wattage of power supply would be able to support this hardware. I had a 350W in mind... would that do?

    Read the article

  • I can't get my PC to start up by a normal way.

    - by ssice
    I couldn't write a more accurate title. I am just unable to start the computer by pressing the Power On button. I checked the Power Supply and it seems to give good voltage values in every pin. And this is not a BIOS malfunction because of bad overclocking or anything that may come to your mind. And I will tell you why. It happens that EPS (or any ATX-based) power supply has the ability to be powered-on by the Motherboard by jumping the 13th pin of the 24-pin-ATX-connector to COM/GND. I did it, after pushing the power on button (without any visual response) and, pwhaa! The machine turned on. I was able to read (and even write, if I wanted) BIOS values and then start any OS installed. Machine starts, so it's not any kind of misconfiguration. It seems some hardware related. I am able to power the machine on only if I already pushed the power on button. Though pushing it without jumping the 13th pin to ground for a second does not power the machine. Of course, jumping the pin without pushing the power on button does not tell the motherboard anything, so the computer would not start up either. It's as if the logic that connects the power button with the 13th pin derivation to GND was unable to be activated. What can be the issue? How can I solve it? My configuration is as follows: CPU: AMD Phenom 9850 X4 Black Edition MB: ASUS Formula II AM2 RAM: 2x2GB Corsair Dominator 5-5-5-15 2T @ 1066MHz DDR2 Tested also with only 1 module GPU: 2x XFX nVIDIA GeForce 9600 GT XxX Alpha Dog Edition @ Core: 540Mhz [SLi] Power Supply: Xilence 700W (ATX 12V 2.3 / EPS 12V 2.92 compatible) PS: I know the machine is like 2 years old. I hardly use it now, but my parents do.

    Read the article

  • How can I play Blu-Ray movies on a PC upgraded to Windows 8?

    - by Rowland Shaw
    How can I play Blu-Ray movies via Windows Media Centre on Windows 8? If I choose the "play dvd" option, I get an error: Cannot Play Disc To play this DVD, you must first install a playback application that supports Blu-ray Disc. [ OK ] However, I have got the HP MediaSmart application installed, which does work (although it's "less than awesome"), so I'm confused why I get this warning?

    Read the article

  • Win 7 crashes, PC reboots and says "Hard drive 0 not found" until I turn if off and on again

    - by Danny T.
    I recently made the move from Windows XP to Windows 7. Since then, when my computer is on for a few hours it always ends up rebooting without warning. Then the BIOS won't recognize my hard drive (hard drive 0 not found). If I turn off my computer and then on again, it boots normally. Some details: Dell Dimension 9150 Windows 7 I updated the BIOS I updated all system drivers with the latest version from Dell (SATA, Chipset, etc.) Other drivers updated too (Graphic card, sound, etc.) There is one thing that I tried after some Googling: I turned off the DMA access to the drives, but it's still rebooting after a few hours. Any clue? UPDATE 2010/12/13 Here are the events from the Event Log for today, from when I turned the computer on until it crashed: 19:17 - Error - ID 10016 - DistributedCom 20:06 - Error - ID 1008 - Customer Improvement Program (could not send data to Microsoft) 21:48 - Critical - ID 41 - Kernel-Power (System was restarted without proper shutdown) 21:48 - Error - ID 6008 - EventLog (Previous system down was not planned) 21:48 - Error - ID 1101 - EventLog (Audit Event ignored) 21:49 - Error - ID 10016 - DistributedCom Both DistributedCom events have a description along these lines (translated from French): The authorisation parameters specific to the application are not allowing Local Execeution for the COM server application with the CLSID {C97FCC79-E628-407D-AE68-A06AD6D8B4D1} and the APPID {344ED43D-D086-4961-86A6-1106F4ACAD9B} to the SID AUTHORITY NT\User System (S-1-5-18) from the address LocalHost (LRPC usage). This security authorisation can be changed with the Component service administration tool. UPDATE 2010/12/31 Here are the error messages I have on blue screens : STOP C000007xA - Kernel_Data_Inpage_Error "Unkown hard error" C00000135 - Can't start because &hs is missing

    Read the article

  • Apache2 Virtual Host broken; displayed default index.html on subdomain, but correct content on www.subdomain

    - by Robert K
    I've got a Linode configured as a Ubuntu 10.04.2 web server with Apache 2.2.14. I have a total of 4 sites, all defined under /etc/apache2/sites-available as virtual hosts. All sites are almost identical clones for configuration. And all sites but my last work successfully. default: (www.)exampleadnetwork.com (www.)example.com reseller.example.com trouble: client1.example.com I keep getting this page when I visit the client1.example.com site: It works! This is the default web page for this server. The web server software is running but no content has been added, yet. In my ports.conf file I have the NameVirtualHost correctly set to my IP address on port 80. If I access the "www.sub.example.com" alias the site works! If I access it without the www I see the "It Works" excerpt posted above. Even apache2ctl -S shows that my vhost file parses correctly and is added to the mix. My vhost configuration file is as follows: <VirtualHost 127.0.0.1:80> ServerAdmin [email protected] ServerName client1.example.com ServerAlias client1.example.com www.client1.example.com DocumentRoot /srv/www/client1.example.com/public_html/ ErrorLog /srv/www/client1.example.com/logs/error.log CustomLog /srv/www/client1.example.com/logs/access.log combined <directory /srv/www/client1.example.com/public_html/> Options -Indexes FollowSymLinks AllowOverride None Order allow,deny Allow from all </directory> </VirtualHost> The other sites are variations of: <VirtualHost 127.0.0.1:80> ServerAdmin [email protected] ServerName example.com ServerAlias example.com www.example.com DocumentRoot /srv/www/example.com/public_html/ ErrorLog /srv/www/example.com/logs/error.log CustomLog /srv/www/example.com/logs/access.log combined </VirtualHost> The only site the differs is the other subdomain: <VirtualHost 127.0.0.1:80> ServerAdmin [email protected] ServerName reseller.example.com ServerAlias reseller.example.com DocumentRoot /srv/www/reseller.example.com/public_html/ ErrorLog /srv/www/reseller.example.com/logs/error.log CustomLog /srv/www/reseller.example.com/logs/access.log combined </VirtualHost> Filenames are the FQDN without the www. prefix. I've followed this advice, but still cannot access subdomain properly.

    Read the article

  • Can connect to WAN via PC but router doesnt.

    - by user16877
    I have a very strange problem regarding the office network. We are currenltly in a executive suite and when i connect to wan via ethernet cable i get dhcp assigned IP address in my network config. I hooked up the linksys router to the wall expecting it to receive all the necessary ip info but that didnt work. So we have been assigned static ip address to put in to our router later but even with the static ip router doesnt seem to connect to internet. But using the same ip address and assigning to laptop works. I m very puzzled what might be the cause of this so any help is really appreciated.

    Read the article

  • How Can I Map IIS on My PC with Static IP to my Domain Name?

    - by Subhen
    Hi, Now I have got an internet connection with Static Ip. I want to know How can I map my website to my Static IP(Received from ISP). I know this is not a good Idea for Security and Performance issues, But just Wanted to know as I can set up a test Project. Again, Can't I just by a domain name and map it to my Static Ip, instead of buying them from WebHosting Providers. Now I have bought the space from bizzhost and hosted my site by setting the Name Server. Thanks, Subhen

    Read the article

  • What is the largest flatscreen monitor available for PC use?

    - by Avery Payne
    I'll qualify this specifically (by order of preference): must have the highest diagonal measurement, widescreen or "normal" aspect ratio doesn't matter here, just the diagonal. must have the highest resolution available, which means 72 inches of 1280x1024 won't cut it. must not have a TV tuner built into it, I'm not looking for a TV set, this is a monitor! must be available at a retail outlet that caters to the general public, i.e. Best Buy, Sears, Costco (all of these examples are in the U.S., although you can suggest something from whatever chain is in your area/nation/geography). Non-retail or non-physical venues like eBay, or businesses that only cater to other businesses, do not qualify under this requirement. I should be able to walk into this place and purchase it, not just whip up an order online. If you are unsure about this requirement, just ask yourself: can I physically see it before I open my wallet and purchase it?

    Read the article

  • Why does remote desktop connection flash from one PC but not others?

    - by Randy Orrison
    I have 20 PCs (Windows XP) in remote locations connecting to the same server (Windows Server 2003) using Remote Desktop over a VPN. On just one of the PCs the remote desktop screen flashes (redraws) multiple times after connecting, the others don't. The screen resolution is the same: local is 800x600 32bit; RDP file is set to full screen, 256 color; remote when connected is 800x600 8bit color. Any suggestions what the problem might be, or what to investigate next?

    Read the article

  • How do I get rid of malicious spyware, malware, viruses or rootkits from my PC?

    - by Gnoupi
    What should I do if my Windows computer seems to be infected with a virus or malware? What are the symptoms of an infection? What should I do after noticing an infection? What can I do to get rid of it? This question comes up frequently, and the suggested solutions are usually the same. This community wiki is an attempt to serve as the definitive, most comprehensive answer possible. Feel free to add your contributions via edits.

    Read the article

  • Windows: Is there something to see and remotely control single(!) windows on a remote PC?

    - by Horst Walter
    Is there something where I can see and control single(!) windows of PC1 on PC2 remotely. Basically like it is possible with X-Windows. I am not talking / asking about A software which displays the whole desktop remotely (like VNC, Windows RDP). A X-windows server for windows, to connect to Linux. The answer here ( Windows Remote Desktop Connection for just a single window (or a single program) ) requires Windows Server 2008. I need to run this on two Windows 7 machines. Example: PC1 shows three windows, and I transfer, see, and control window 2 on PC2. -- Edit -- I have checked whether there is an X-Server for Windows <- Windows. But there seems not to be one other than Unix <- Windows: http://stackoverflow.com/questions/40453/what-is-a-good-and-free-x-server-for-windows

    Read the article

  • Setting up Virtual Hosts with Apache on Windows 2008 server for multiple sites. Complicated setup, including subversion

    - by Roeland
    I am setting up apache on my windows 2008 server at my home. It will serve 2 functions. Subversion hosting to allow me and some others to manage company documents with version control Local website hosting for web development. Will need to run several websites since I generally work on more then one site at a time. Heres what I have done so far. I set up subversion and apache 2.2 using some walk troughs. I changed the default port to 1337. (im a nerd) Using dyndns.com I created a domain to forward to my home ip which is dynamic. ( company.gotdns.org) I then went into my DNS for my company.com and added a record to point repo.company.com to company.gotdns.org At this point people who need access to my file repository can access by going to repo.company.com/repo which is good so far. My question comes on the next step, setting up virtual hosts with apache. Ideally I would like to have my local website be viewable by some others in the company from their homes. So, say I am working on site1, I would like to have them be able to view this by going site1.roeland.bythepixel.com. At the same time, I would like to have site10.wouter.bythepixel.com go to his local setup for site10. What I have done for this: I went into my DNS for company.com and added a record to point roeland.company.com to company.gotdns.org (which translates to my ip). I added code to my httpd-vhosts.conf (listed at bottom) I added code to my host file (listed at bottom) Hah, so of course this doenst work as excepted.. going to site1.roeland.bythepixel.com doesnt bring up my test1 site. Could anyone point me where I may be going wrong? Thanks! hosts: 127.0.0.1 localhost 127.0.0.1 sensenich.roeland.bythepixel.com ::1 localhost httpd-vhosts.conf: <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot "F:/Current Projects/sensenich.com" ServerName sensenich.roeland.bythepixel.com ErrorLog "logs/sensenich.roeland.bythepixel.com-error.log" CustomLog "logs/sensenich.roeland.bythepixel.com-access.log" common </VirtualHost>

    Read the article

  • How is the 137GB limit counted in Virtual PC (two systems on one disk)?

    - by Nux
    I have a dual boot (Win7, XP) physical machine on my old computer which I want to virtualize and move to my new one. So I've uninstalled everything that I can and run shrink from RescueCD (used GParted). Now I have two about 80GiB partitions with a gap between them, so still this seem to be above the given limit. Still the resulting VHD (made with Disk2vhd) is much below the limit (about 110GiB) and both partitions are below the limit. So my question is - is it failing due to the limitations of disk size for VPC or is failing simply because it's a dual boot system. Or maybe it would work if I would move partitions to be close to each other (the gap between them is about 171GB and the whole physical disk is 1TB)?

    Read the article

  • How much information can websites get about your browser/PC?

    - by Pickledegg
    I am trying to determine if the information shown on this website is the absolute maximum amount of information that a webserver can obtain from a web visitor. Does anyone know of any other sites that will be able to get more information from the user passively like this? I'm not talking about port-sniffing or any kind of interaction from the user, just the info that a server can get from a 'dumb' visit.

    Read the article

  • Why can't I ping a PC on my home network?

    - by AngryHacker
    Whenever I try to ping another box on my home network, it pings the wrong ip address: C:\Users\Papa>ping macmini Pinging macmini.belkin [208.68.143.55] with 32 bytes of data: Reply from 208.68.143.55: bytes=32 time=50ms TTL=110 As you can see it always appends belkin to anything I try to ping. So I hit up ipconfig and belkin happens to be Connection-specific DNS Suffix: Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : belkin IPv4 Address. . . . . . . . . . . : 192.168.2.7 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.2.1 My setup is all DHCP, so I am not sure where belkin is coming from. I looked through all the networking stuff, as you can see below: Bottom line: how do I fix this?

    Read the article

  • Can't see a Windows XP computer on the network

    - by user56614
    I have two PC's connected to the same router. One is running Vista Home Premium and the other is running XP Pro. I'm trying to reach the shares of second PC from the first PC. I've enabled file sharing on the XP PC, I've disabled firewall and defender, and I can successfully ping it from the Vista PC. Both computers are set to the same workgroup "WORKGROUP". However, if I try to type "\\192.168.1.2" in Windows Explorer (192.168.1.2 being the IP address of the XP PC), I get a message: "Windows can't access \\192.168.1.2... Error code: 0x80004005 Unspecified error". And If I type "net view \\192.168.1.2" in command prompt, I get "System error 53 has occurred. The network path was not found." Am I missing something trivial?

    Read the article

  • Client PC not booting when certain TFT plugged in - TFT or graphics card failure?

    - by Chake
    here comes something quite strange: On a client machine (DELL Vostro 420) we experienced problems when booting: when turning on the machine beeps normal but doesn't display anything and doesn't boot. After some testing I found out, that this only happens if one (of the two) monitors (Iiyama ProLite E2472HDD) is plugged in while booting. If the other monitor (TFT 2) is plugged in everything is fine. Here a small illustration, TFT 1 is the bad guy: TFT 1 | TFT 2 | failure x | x | x x | | x | x | After BIOS-Phase I can safely plug in TFT 1 and everything works just fine. The question is, what can be done to avoide this behavior: Change monitor? (Iiyama ProLite E2472HDD) Change graphics card? (GeForce 9800 GT) Other suggestions?

    Read the article

< Previous Page | 150 151 152 153 154 155 156 157 158 159 160 161  | Next Page >