Search Results

Search found 5290 results on 212 pages for 'refresh rate'.

Page 155/212 | < Previous Page | 151 152 153 154 155 156 157 158 159 160 161 162  | Next Page >

• 1080p monitor: connected through VGA - perfect, HDMI - awful

  - by develroot

  When I connect my 23" monitor (1920x1080) to my pc through HDMI, I encourage some problems. It's not full screen That's it. There are ~1cm black borders on right and left side and ~0,5cm black borders on the top and the bottom of the monitor. That's pretty frustrating. I tried adjusting overscan, but I can't mannualy type the % of overscan that I need. I can only select between ex. 8 and 10% in AMD Vision Engine Control center, but what I need is 9%. Next, even if i select 10% and the image fits all the corners, but after log off all the settings are lost and I have to do it again and again. Text, images, everything looks blurry That surprised me a lot. Should'nt HDMI quality be better than VGA's one? When connected through HDMI, the text isn't readable. It's like a very low refresh rate, although i'm running at 60Hz. Also the text has something like little shadows, very very annoying. Are there any tips to get the same quality as with VGA, with HDMI ? (running on integrated ATI Radeon HD4200, which, appearently, is the best card I have ever seen in terms of integrated ones)

  Read the article

• Is there any proper documentation for mod-evasive?

  - by Question Overflow

  mod_evasive20 is one of the loaded modules on my httpd server. I read good things about how it can stop a DOS attack and wanted to try it out on my localhost. A search for mod_evasive turns up a blog post by the author which briefly describes what it does. Other than that, I can't seem to find a reference or a documentation on the apache modules site. I was wondering whether it is a module recognised by Apache since there is no mention of it on its website. I have a mod_evasive.conf file sitting in the /etc/http/conf.d folder that contains the following lines: LoadModule evasive20_module modules/mod_evasive20.so <IfModule mod_evasive20.c> DOSHashTableSize 3097 DOSPageCount 2 DOSSiteCount 50 DOSPageInterval 1 DOSSiteInterval 1 DOSBlockingPeriod 10 </IfModule> My understanding from the setting is that if I were to click refresh or send a form more than two times in a one second interval, apache will issue a 403 error and bar me from the site for 10 seconds. But that is not happening on my localhost. And I would like to know the reason. Thanks.

  Read the article

• Does migrating 2 domain controllers between 2 datacentre requires both virtual machines to be shut down at the same time?

  - by Imagineer

  I was attempting to migrate 2 virtual machines that are domain controllers between 2 datacentres running ESX 3.5 and ESX 4.1. I was advised to shut down both domain controller at the same time during the migration process. This is to avoid USN Rollback and other replication issues. The following are the steps that I was planning to perform: 1. Shutdown both DC. 2. Copy both VMs files across to new datacentre using Veeam FastSCP (connection to both vCentre through IP address instead of hostname) 3. Power them up at new datacentre. 4. Configure Network interface/DNS/DHCP for both DCs in new datacentre I have tried to use Veeam FastSCP rather than VMware Standalone Converter is because its copying rather than converting. Someone also suggested that I use backup and restore app like Veeam backup and replication software. Sounds like a simple job, but after shutting down both DCs, the transfer rate using FastSCP is so slow registering only 1KB/s as oppose to the normal 1MB/s (or more). When that attempt to transfer failed, I tried to cold clone both DCs resulted in the both ESX hosts get disconnected. I have tried troubleshooting by referring to this - VMware KB - Diagnosing an ESX Server that is Disconnected or Not Responding in VirtualCenter It seems that the DNS being down is the caused of all unusual occurrence. The moment I powered up the DCs via VMware console command, the ESX host were able to connect to the vCentre again. How can I avoid such a pitfall again? Am I doing it correctly? Any help would be greatly appreciated! Thank you.

  Read the article

• Can a USB/IDE/SATA adapter be flaky?

  - by Ward

  I use USB/IDE/SATA converters a lot and on the two that I have now, I sometimes get errors copying files to drives. It only happens when I'm copying big files to the drive (big can mean as little as 100MB, I think it happens more often with bigger files - 300MB or more), and basically the copy will fail and I'll get one or more error messages about "Delayed write failed." But if I disconnect the drive and re-connect it, I'll usually be able to continue. (The file that was being copied will be corrupt, but otherwise the drive is fine.) I just noticed a new type of flakiness: the data transfer rate can vary widely. I copied one set of files (5x300MB files) and it took 10+minutes, then I copied another set (approx. the same sizes) and it took less than a minute. I haven't done systematic testing, the other things I'm doing on my laptop at the same time might have some impact, and I haven't cross-checked the two adapters I have and the 3 hard drives I'm working with to see if there's a pattern. I'm more wondering if anyone else has seen anything like this.

  Read the article

• Notebook display problem (multiplication)

  - by SubniC

  Hi, I'm having some troubles with the display of a LG E500 notebook. The thing is that without any known reason the display starts to show the screen divided in eigth parts and each part show the display image as if I had a matrix of eigth displays :) I thought it could be some kind of refresh rate problem or driver related, but it is happening at boot-up as well and the BIOS. I got the computer completely unassambled yesterday and I check all the wires and connectors looking for something broken or unconected, but without luck... You can see a picture here of the problem (sorry for the low quality, but I think it illustrate the problem. EDIT 1: I uploaded a new pictrue, here you cans ee the problem better :) There are three horizontal lines that you can see just between the windows. You can see the grey line at the first moment you turn on the computer and the after the duplicated screens show up just like if they where arranged over a grid (over the horizontal lines...) I hope it makes any sense. Do you know what could be happening? or can you tell me what would you do? Thank you very much for your help.

  Read the article

• Can Internet data be used by malware when PC off?

  - by Val

  I have noticed over the last month that my off peak data has been used at a rate of approx 350MB per hour - this has meant that I have gone over my quota and slowed down by my ISP to 256k. There is no one in the house using it (2am-8am is my ISPs off peak hours) at that time. My PC and other wireless devices (ipad and iphone) are turned off. I have changed the wireless password on my modem 3 times and it is now 30 digits long. So I don't think someone else is using my wireless access between 2-8am. It has been suggested by my ISP that I may have malware/spyware on my computer. Sorry for my ignorance, but can malware still run if the PC is off? I did look at my modem's log and followed an IP address to a service called Amazon Simple server Storage. Could this company possibly be the culprit? I am not too tech savvy, so any assistance appreciated. I have run a barrage of spyware cleaning software eg malware bytes; spy bot etc.... Cheers Val

  Read the article

• Large, high performance object or key/value store for HTTP serving on Linux

  - by Tommy

  I have a service that serves images to end users at a very high rate using plain HTTP. The images vary between 4 and 64kbytes, and there are 1.300.000.000 of them in total. The dataset is about 30TiB in size and changes (new objects, updates, deletes) make out less than 1% of the requests. The number of requests pr. second vary from 240 to 9000 and is dispersed pretty much all over, with few objects being especially "hot". As of now, these images are files on a ext3 filesystem distributed read only across a large amount of mid range servers. This poses several problems: Using a fileysystem is very inefficient since the metadata size is large, the inode/dentry cache is volatile on linux and some daemons tend to stat()/readdir() it's way through the directory structure, which in my case becomes very expensive. Updating the dataset is very time consuming and requires remounting between set A and B. The only reasonable handling is operating on the block device for backup, copying, etc. What I would like is a deamon that: speaks HTTP (get, put, delete and perhaps update) stores data it in an efficient structure. The index should remain in memory, and considering the amount of objects, the overhead must be small. The software should be able to handle massive connections with slow (if any) time needed to ramp up. Index should be read in memory at startup. Statistics would be nice, but not mandatory. I have experimented a bit with riak, redis, mongodb, kyoto and varnish with persistent storage, but I haven't had the chance to dig in really deep yet.

  Read the article

• Passwortgeschützter Traffic-meter

  - by UncleBob

  Hallo erstmal, ich habe hier ein kleines Problem für das ich bis jetzt noch keine Lösung habe. Ich lebe in Bosnien und teile hier die Internetverbindung mit der Vermieterin, und wie es in Bosnien so ist haben wir keine Flatrate, sondern eine 15 Giga traffic limite. Das wäre eigentlich mehr als genug, wenn der Sohn der Vermieterin nicht immer überziehen würde, sodass die Rechnungen immer ziemlich teuer ausfallen. Ich habe ihm bereits ein Messprogramm installiert, aber das schaltet er offensichtlich aus sobald er in die Nähe seiner Limite kommt und behauptet dann die Limite nicht überzogen zu haben. Ich brauche also mindestens ein Messprogramm das Passwortgeschützt ist und/oder im Log Zeiten vermerkt wärend denen es nicht eingeschaltet war. Noch besser wäre ein Programm das ihm den Netzzugriff einfach abklemmt wenn er seinen Anteil überschreitet, also eine Mischung aus Trafic-meter und Parental Guard. Kann mir da jemand weiterhelfen? Gtranslated version Hi first, I have a small problem for which I yet have no solution. I live in Bosnia and share the Internet connection here with the owner, and how it is in Bosnia, we do not have a flat rate, but a 15 Giga traffic limite. That would actually would be more than enough, if the son of the landlady does not always cover so that the bills always turn out quite expensive. I have it already installed a monitoring program, but he apparently turns out as soon as he comes close to its limit and then claims not to have the limit excessive. I therefore need at least a measurement program that is password protected and / or in the log notes During low periods where it has not turned on. Even better would be a program that disconnects him from accessing the network if it simply exceeds its share, ie a mixture of Traffic parameters and Parental Guard. Can someone help me there?

  Read the article

• SSD for swap on Ubuntu server

  - by grs

  Currently I am reading SSD reviews and I wonder how much exactly I will benefit if I move the 24 GB swap from 7200rpm HDD to SSD. Does anyone implemented swap space on SSD? Is this generally good idea? On a side note: I read that ext4 has much better performance if the journal is on SSD. Anyone with such a setup? Thanks! Edit: Here I will answer the questions posted: Occasionally, relatively rare I am hitting the swap. I know what the swap is for and that is better to get more RAM. When the server begins to swap its performance degrades (not a surprise). The idea is if I have few memory hungry processes running, to improve the overall system performance at that time, using SSD for swap, instead of slower rotational media. At the end - I want to be able to login faster and check the server state during swapping, instead of waiting on the login prompt. And of what I see SSD is cheaper per GB than RAM. Would I have better server performance during swapping (as rare it is) using SSD compared to HDD? Where 10k or 15k rpm HDDs would rate in this scenario? Thank you all for your quick and prompt answers!

  Read the article

• iptables drops some packets on port 80 and i don't know the cause.

  - by Janning

  Hi, We are running a firewall with iptables on our Debian Lenny system. I show you only the relevant entries of our firewall. Chain INPUT (policy DROP 0 packets, 0 bytes) target prot opt in out source destination ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 state NEW Chain OUTPUT (policy DROP 0 packets, 0 bytes) target prot opt in out source destination ACCEPT all -- * lo 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED LOGDROP all -- * * 0.0.0.0/0 0.0.0.0/0 Some packets get dropped each day with log messages like this: Feb 5 15:11:02 host1 kernel: [104332.409003] dropped IN= OUT=eth0 SRC= DST= LEN=1420 TOS=0x00 PREC=0x00 TTL=64 ID=18576 DF PROTO=TCP SPT=80 DPT=59327 WINDOW=54 RES=0x00 ACK URGP=0 for privacy reasons I replaced IP Addresses with and This is no reason for any concern, but I just want to understand what's happening. The web server tries to send a packet to the client, but the firewall somehow came to the conclusion that this packet is "UNRELATED" to any prior traffic. I have set a kernel parameter ip_conntrack_ma to a high enough value to be sure to get all connections tracked by iptables state module: sysctl -w net.ipv4.netfilter.ip_conntrack_max=524288 What's funny about that is I get one connection drop every 20 minutes: 06:34:54 droppedIN= 06:52:10 droppedIN= 07:10:48 droppedIN= 07:30:55 droppedIN= 07:51:29 droppedIN= 08:10:47 droppedIN= 08:31:00 droppedIN= 08:50:52 droppedIN= 09:10:50 droppedIN= 09:30:52 droppedIN= 09:50:49 droppedIN= 10:11:00 droppedIN= 10:30:50 droppedIN= 10:50:56 droppedIN= 11:10:53 droppedIN= 11:31:00 droppedIN= 11:50:49 droppedIN= 12:10:49 droppedIN= 12:30:50 droppedIN= 12:50:51 droppedIN= 13:10:49 droppedIN= 13:30:57 droppedIN= 13:51:01 droppedIN= 14:11:12 droppedIN= 14:31:32 droppedIN= 14:50:59 droppedIN= 15:11:02 droppedIN= That's from today, but on other days it looks like this, too (sometimes the rate varies). What might be the reason? Any help is greatly appreciated. kind regards Janning

  Read the article

• xrandr fails when 3rd monitor has higher resolution

  - by Pi3cH

  I tried many combinations with xrandr command under lubuntu 12.04 to setup my three monitors DVI (DELL 1) left detected as HDMI1 HDMI (LG E2290) middle detected as HDMI2 VGA (DELL 2) right detected as VGA1 I can get the display with fix 1280x1024 on all the monitors. But once I setup 1280x1024 + 1920x1080 + 1280x1024, I get blank screen on all the monitors. Sometimes it throws crts fail error instead of blanking out. Anyone have similar issues? any solutions/workarounds? P.S. I can setup two monitors using 1280x1280 and 1920x1080 P.S.S. HDMI2 required at least 1920x1080 to display sharp picture. Outputs (it seems graphic card supports up to 8192x8192): xrandr Screen 0: minimum 320 x 200, current 3840 x 1024, maximum 8192 x 8192 VGA1 connected 1280x1024+2560+0 (normal left inverted right x axis y axis) 338mm x 270mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 HDMI1 connected 1280x1024+0+0 (normal left inverted right x axis y axis) 376mm x 301mm 1280x1024 60.0*+ 75.0 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 HDMI2 connected 1280x1024+1280+0 (normal left inverted right x axis y axis) 477mm x 268mm 1920x1080 60.0 + 1680x1050 60.0 1280x1024 75.0 60.0* 1152x864 75.0 1024x768 75.1 60.0 800x600 75.0 60.3 640x480 75.0 60.0 720x400 70.1 DP1 disconnected (normal left inverted right x axis y axis) DP2 disconnected (normal left inverted right x axis y axis) 3 CRTs (0,1 VGA, 0,1,2 for other HDMI) xrandr --verbose VGA1 connected 1280x1024+2560+0 (0x47) normal (normal left inverted right x axis y axis) 338mm x 270mm Identifier: 0x42 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 0 CRTCs: 0 1 ... HDMI1 connected 1280x1024+0+0 (0x47) normal (normal left inverted right x axis y axis) 376mm x 301mm Identifier: 0x43 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 1 CRTCs: 0 1 2 ... HDMI2 connected 1280x1024+1280+0 (0x47) normal (normal left inverted right x axis y axis) 477mm x 268mm Identifier: 0x44 Timestamp: 51324 Subpixel: unknown Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 2 CRTCs: 0 1 2 Below command fails: xrandr --output VGA1 --auto --output HDMI2 --auto --left-of VGA1 --output HDMI1 --auto --left-of HDMI2 Below command passes: xrandr --output VGA1 --auto --output HDMI2 --mode 1280x1024 --rate 60.0 --left-of VGA1 --output HDMI1 --auto --left-of HDMI2 Graphic card VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09)

  Read the article

• ASP.Net Session Timing Out Rapidly

  - by Zac

  We have an ASP.Net 3.5 website running on Windows Server 2008 with IIS7. The session timeout period for this site is configured to be 20 minutes - however, it is currently lasting for between 40 and 50 seconds. After researching the problem we investigated several configuration values which could be involved in the timeout period but none of them are set to less than 20 minutes. The areas we look are as follows: web.config system.web/sessionState element (20 minutes). web.config system.web/authentication/forms element (not present, defaults to 30 minutes). Sites/{website}/ASP/Session Properties/Time-out (20 minutes). Application Pools/{appPool}/Advanced Settings/Process Model/Idle Time-out (20 minutes). We've also noted that the CPU is staying around 0% and that RAM usage is flat-lining around 1.07 GB (of 8 GB available) - so there is no performance-based reason for IIS to be recycling the Application Pool as far as we can tell. Are there any settings we've overlooked which could cause the session timeouts to be expiring so quickly? EDIT A couple of additional points: This is not occurring in development, only on the server. The session is not sliding (i.e. if we refresh the page a few times it still times out approximately 40 - 50 seconds after the session was created.

  Read the article

• Why is my rsync so slow compared to pure cp or even scp?

  - by nfm

  I'm transfering the files from Linux to Windows 7 via a mounted share (the share is mounted from Windows on Linux).. I'm copying lots of data (i.e. nearly a TB) from the old to the new machine within my LAN. I'm unfortunate enough already that I only have 100MBit. Naturally I blindly used rsync but already wondered after a day why it feels so slow. Enabling the progress meter showed my a transfer rate of about 2MBit/s . So I took a reasonable big file (800MB) and tracked the transfer timing: cp : 05:33 scp (*): 06:33 rsync : 21:51 *) scp via localhost to the same Linux machine directly onto the share; completely useless but provided a progress meter The tests were as simple as (cp|scp|rsync) <source> <destination> No special arguments except host/port for scp. I even tried the -W switch for rsync but cancelled after ten minutes. rsync is 3.0.3 running on Lenny. To be able to interrupt the copy process anytime and resume lead me to rsync, but now I think I seriously need to reconsider this requirement. How's such a big difference possible?

  Read the article

• krenew command not working : Permission Denied

  - by prathmesh.kallurkar

  I am using a Linux server to perform my simulations. The login and the file-system of the server are protected using kerberos. The file-system is supported using NFS. Since my simulations take a lot of time to run, my ssh sessions used to hang regularly. So, I have started running my simulations in byobu (similar to screen). In order to make sure that my kerberos session remains active, I am using the krenew command. I have entered the following command in my .bash_profile file. (I am sure that it is called for every login) killall -9 krenew 2> /dev/null krenew -b -t -K 10 So everytime I ssh to the server, I kill the existing krenew command. Then, I spawn a new krenew command -b (which runs in background), -t (I forgot why I was using this option !), and -K 10 (It must run after every 10 minutes and refresh the kerberos cache). When I run the simulations, It runs for 14 hours and then suddenly, I am getting error for reading file Permission Denied Is the command that I am running incorrect ??

  Read the article

• Win7 'locking' process/files/folders?

  - by Dynde

  I've had a fair bit problems with sometimes files/folders/processes being 'locked' by Windows. The weird thing is, it's not like the traditional sense, I think, where tools like UnlockIT and wholockme would work. It seems that just giving it a little often helps - making me think it could either be the HDD, the memory, or something in Windows. A scenario: I go into a folder - don't open anything at all, go back up, cut or drag-move the folder to someplace else, it says "Action can't be completed because the folder or a file in it is open in another program". Waiting sometimes 20 seconds sometimes a little longer, and I can move it. Another scenario is deleting a bunch of files in a folder, and it appears that everything is gone, but then suddenly after a few seconds an .exe file pops back up, and I can't delete it. Waiting a few minutes, then pressing refresh and it's gone. I have the strangest feeling that there's a problem with either HDD or memory. I already tried disabling Windows indexing service with no luck. Does anyone have any ideas? EDIT: I should say, that I have a very fast system, 16 GB DDR3 RAM, i7-2600k CPU, SSD main HDD, so I really should not be experiencing any sort of problems, where one might say that it's "reasonable" for the system not to respond right away. Edit2: And I updated SSD firmware a couple months ago, so it shouldn't be bad release FW either

  Read the article

• How to Upgrade PHP 5.2 to 5.3 on Windows Plesk Panel 8.2

  - by Jagat Sheth

  I need to upgrade my server PHP version becasue of Wordpress New version not support PHP 5.2. On My server windows 2003 stansard edition x64 with SP1 installed, IIS 6.0, MySQL 4.1, Plesk Panel 8.2. I have follow listed steps on plesk KB. http://kb.parallels.com/6670 How to update PHP 5 on a Windows server with Parallels Plesk Control Panel 8.x and 9.x installed. In order to upgrade PHP 5 to the necessary version (other than shipped with Parallels Plesk), please perform the following steps: Stop Plesk services (‘Control Panel’ and all that are included in the ‘Plesk Run-Time’ section) Rename folder %plesk_dir%\Additional\PleskPHP5 to the orig_PleskPHP5 Create a new folder %plesk_dir%\Additional\PleskPHP5 Download necessary version of PHP, unzip its content, and copy it to the newly created folder PleskPHP5 Copy the file php.ini from the old folder orig_PleskPHP5 to the new one Make sure the permissions are inherited Start Plesk services Click the "Refresh" button in the Components Management section in Parallels Plesk Panel and check if you can see the new PHP version there After follow steps when I open a PHP info it shows me specified module could not be found. If anybody know solution Kindly help me is highly priority. I am very thankful if any one help me to solve this ASAP. Thanks and regards, Jagat Sheth

  Read the article

• Running .NET code in XML file [closed]

  - by Stuart McIntosh

  We have 2 servers, 1 already configured with .net which works fine and a new one which appears to be configured the same but when I open an xml page in Internet Explorer it complains about the <% tag. We have IIS on win srvr 2003 SP2. The website is configured with .NET 1.1.4322. In ISAPI extensions have set the .XML extension to use c:\windows\microsoft.net\framework\v1.1.4322\aspnet_isapi.dll But the page: <property name="documentmaxage" value="0"/> <property name="documentmaxstale" value="0"/> <var name="m_Prompt_Path" /> <form id="InitVoiceXmlDoc"> <block> <assign name="m_Prompt_Path" expr="&quot;<% Response.Write(Request.QueryString["m_Prompt_Path"]); %>&quot;"/> </block> </form> gives the error: The XML page cannot be displayed Cannot view XML input using XSL style sheet. Please correct the error and then click the Refresh button, or try again later. The character '<' cannot be used in an attribute value. Error processing resource 'http://localhost:11119/fails.xml'. Lin... &quo... We have the same config on another server which works fine. So are there other options apart from the ISAPI extensions that I need to look at

  Read the article

• computer freezes but music continues

  - by Danny

  Recently I have had a problem where my computer will freeze completely but if I happen to be streaming Pandora in a tab that will continue playing. If I wait about 2-5 minutes it will eventually come back and start working normally. I also noticed that during the period that it is unresponsive that the HDD activity light stays lit the whole time, not flashing. I've ran memtest86+ and a diagnostic from Western Digital for my HDD model and none of them reported any errors. The specs for my computer are 1 x ASRock H55M/USB3 R2.0 LGA 1156 Intel H55 HDMI USB 3.0 Micro ATX Intel Motherboard 1 x CORSAIR Enthusiast Series CMPSU-550VX 550W ATX12V V2.2 SLI Ready CrossFire Ready 80 PLUS Certified Active PFC Compatible with Core i7 Power Supply 1 x Intel Core i3-540 Clarkdale 3.06GHz LGA 1156 73W Dual-Core Desktop Processor Intel HD Graphics BX80616I3540 1 x G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model F3-12800CL9D-4GBNQ 1 x ASUS PCE-N13 PCI Express 150/300Mbps Transfer/Receive Rate Wireless Adapter 1 x EVGA 01G-P3-1556-KR GeForce GTX 550 Ti (Fermi) FPB 1GB 192-bit GDDR5 PCI Express 2.0 x16 HDCP Ready SLI Support Video Card I can't imagine what would be causing these problems.

  Read the article

• Why is XSP/mono giving me file/write errors with lucence?

  - by acidzombie24

  I am using mono 2.6.7, xsp 2.8.? and i am not sure what else. I'll try downgrading xsp and whatever else. Today i notice my server randomly gets Http Error 500, internal server error. I looked in my log files http://www.pastie.org/1426236 and it appears that the problem is locking lucence which it does by creating a file called write.lock. This use to work with no problem but now it gives me pain. It will fix itself if i refresh the page several times but it will break just as easily. My other site will not work everytime i restart apache and i need to by hand delete the file (at least it doesnt get random 500 errors). However now it just says Lock obtain timed out: NativeFSLock@/var/www/SITE_2/App_Data/LuceneIndex_a/write.lock no matter what. I even chmod -R 777 the directory and still no luck. write.lock doesnt even exist. I have no clue whats going on. Any ideas?

  Read the article

• How to recover deleted files on ext3 fs

  - by Mike

  I have a drive which was using the ext3 filesystem. I am told that about 10Gb of data was deleted off the drive (probably via rm). The drive is currently mounted as read-only to preserve all data. Does anyone know of a method to restore some or all of the data? Also if it helps, the OS was Fedora. I've also been told that the data is mostly ASCII fortan source code and Matlab files. Conclusion I have finally managed to get the data back, and with the simplest means ever! After weeks of trying and failing to bring back much of any data, I brought someone in today to take a look at it and offer suggestions, he simply cd'd to the directory and everything was there! It was never lost in the first place!!! Needless to say I feel really dumb right now, but I learned quite a lot with this whole fiasco. At any rate, while I was looking through data forensics solutions, I found that the Autopsy, or more specifically the SleuthKit was the most helpful. So I will accept that as the final answer. I would also like to note for anyone that comes across this later on that the most up-voted (currently) answer by sekenre was also helpful and I learned a lot, but ultimately it did not help with the type (very many, and some being very large) of files I was dealing with. So thank to all you that provided suggestions and wish you all the best!

  Read the article

• How can I get multiple video cards to work on linux?

  - by user17943

  I installed fedora 12. I have 2 ATI cards that I used to use on windows to run 4 monitors. A recurring problem has been to get them detected in linux. Only my secondary card is picked up linux. When I manage the displays it detects the 2 monitors connected that card. What are the specific steps I should take to get the second card detected? Supposedly there is a tool system-config-xfree. I don't have it, yum can't find it. Also I heard it has something to do with editing some xorg.conf file or something to that effect. I have absolutely no idea how to find the "bus id" of my card, or lookup the horizontal refresh rates, etc.. I would probably have no problem following the documentation & editing the file if I knew a good way to find these values. Someone also suggested installing linux twice and saving the xorg.conf it generates each time (with different card each time) and then merging the two by hand. That is like killing a fly with a hammer though, when I do this again and again in the future It'd be nice to not have to take twice as long. Thanks

  Read the article

• Software/hardware to build video streaming server?

  - by Sasha Yanovets

  I am looking for a video streaming server solution, something like online TV server, with ability to make live broadcasts in the internet. What software could you recommend for that? What kind of hardware it should run on, should be there anything special? I am looking for a solution that could be scaled up to at least 1000 simultaneous users online with good resolution of video. I think it is good to have general answer on what direction to choose. But here more details on my specific case: I just looking for a solution almost from scratch. We have some video content that we've produced, but it is not delivered over internet yet. We do not tied to any particular vendor for now. We want to make 24 hours of steaming three 8 hour blocks with change of content every day. We want the ability to make regular live broadcasts. I guess we will need to have several options of streaming quality (low ~56 kb/s mid ~273 kb/s). Some terms just foreign to me (like play-truncation rate), if you could point out what parameters we should avare of, it would be great. Uplink to the internet is to be determined. We plan to start from something and scale up on the way. If you are already have some kind of media streaming server, just describe its configuration here (hardware, OS, software), peak number of concurrent users it serves. I think it could help people approaching this task.

  Read the article

• What to do about old MacBook

  - by John

  I have a White MacBook version 10.5.8. I accidentally dropped it and about an inch of the most right side of the screen is blacked out. I can't see the clock and Trash Can because of this. I checked how much it would cost to repair, and the cost of repairing is a flat rate of $300. I thought that was kind of expensive, like a third of the cost of the MacBook itself. accidentally dropping a notebook is something that would happen sooner or later, so I think getting a Lenovo is the best. I ended up getting a MacBook pro 15 inch, but do you think it's worth the money to fix my old MacBook? I even saw some used MacBooks available on Ebay for about $400. Anyways I don't know what to do with it. I do like its screen and keyboard better than the MacBook Pro ones, because the screen is less glare-y and the keyboard is more crisp and fun to type on, and its more wieldy when I'm using it while lying down.

  Read the article

• Google Apps: MX records for zonefile

  - by 23tux

  Hi everybody, I have a question about using Google Apps for handling emails. I don't want to set up a whole entire mail system on my server, so I decided to use Google Apps. The ownership of my domain is approved, and now I'm trying to change the MX records in the zone file of my domain. But I think I'm doing wrong, it doesn't work. I want to use mail.mydomain.com as a adress to the mail server for POP, SMTP and IMAP. My zone file looks like this: $TTL 86400 @ IN SOA ns1.first-ns.de. postmaster.robot.first-ns.de. ( 2011011700 ; serial 14400 ; refresh 1800 ; retry 604800 ; expire 86400 ) ; minimum @ IN NS robotns3.second-ns.com. @ IN NS robotns2.second-ns.de. @ IN NS ns1.first-ns.de. @ IN A 111.111.111.111 localhost IN A 127.0.0.1 www IN A 111.111.111.111 ftp IN CNAME www loopback IN CNAME localhost mail IN CNAME @ relay IN CNAME www @ IN MX 10 ALT1.ASPMX.L.GOOGLE.COM. @ IN MX 10 ASPMX3.GOOGLEMAIL.COM. @ IN MX 10 ASPMX2.GOOGLEMAIL.COM. @ IN MX 10 ASPMX.L.GOOGLE.COM. @ IN MX 10 ALT2.ASPMX.L.GOOGLE.COM. I hope someone can figure out, what's wrong with this configuration. When I start a ping on mail.mydomain.org I get an answer from 111.111.111.111 and not from the google server ALT1.ASPMX.L.GOOGLE.COM. thx, tux

  Read the article

• How to calculate unweighted averages in Excel PivotTable?

  - by yonatron

  I often make PivotTables in which each row contains a number of per-person average measures. I then want to look at the unweighted column average for each measure, and usually make some kind of chart from these. Because my individual cells are often averaged from different numbers of data points, the Grand Total row ends up being a weighted average, which I’m not interested in. So I usually make my own average row a few rows above the table to use for my charts. That’s not too much work, but there’s another problem. I often add a few more people’s worth of data to the PivotTables’ source, then refresh the tables. This means my average row needs to be updated to encompass more rows from the PivotTable. Not a huge deal with one table, but when I have lots of them across lots of sheets, I have to do find/replace on a whole bunch of formulas. So: is there a way to automatically get unweighted column averages in a PivotTable, such that when the table is refreshed, the averages don’t change locations and encompass the newly added (or removed) data Thanks

  Read the article

< Previous Page | 151 152 153 154 155 156 157 158 159 160 161 162  | Next Page >