Search Results

Search found 6605 results on 265 pages for 'complex networks'.

Page 157/265 | < Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >

• Improve wireless performance

  - by djechelon

  Hello, I have a Trust Speedshare Turbo Pro router, which is running on channel 6. I found that the wireless signal (and network performance) dramatically drops from my PDA (I can barely attach to the network, even if I set the PDA's energy settings to maximum wireless performance) when I even exit my room, and I don't have shielded walls or something like that. I can't even stream a SD video from my desktop (connected via LAN) to my laptop using WiFi, while via LAN it works fine. I read that changing router's channel could improve performance due to interference reducing. I found that almost all wireless networks around here run on channels 6 and 11. I tried to go to my router's settings page to change channel, but I found that the combo box only allows me to select 6!! I'm not sure, but I may have been able in the past to change channel, though not to all of the available channels. A few minutes ago I tried a firmware upgrade, but it didn't solve my problem. My question is Is it possible that my router is someway locked to its channel? I bought it on my own, I didn't receive it from my ISP Apart from boosting the antenna power to the maximum (which, by the way, increases the EM radiation my and my family's bodies absorb 24/7 and is little more environment-unfriendly), do you have any tips on getting high quality transmission up to 5 metres from the antenna? Thank you

  Read the article

• Two DHCP interfaces asigned to two default gateways to OS

  - by user140600

  I have a Ubuntu box that has two networking interfaces (eth0 and wlan0). They are both configured for DHCP in /etc/network/interfaces, but they both assign a default gateway: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto wlan0 iface wlan0 inet dhcp wireless-essid test Result of route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.1.1 0.0.0.0 UG 100 0 0 wlan0 0.0.0.0 10.0.0.1 0.0.0.0 UG 100 0 0 eth0 10.0.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 172.16.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 How can I set up /etc/network/interfaces to have only one default gateway, on the interface I want? Worst case scenario, how can I at least control which one gets on top on the route -n command, each boot? Note: This box will travel a lot, and will be connected to different networks, so I don´t know in advance the IP addresses/ranges it will have. Sometimes the default gw interface will be eth0. Sometimes it will be wlan0 ... So, this needs to be kind of automatic ...

  Read the article

• Adding 2nd DC to the domain from a different subnet over VPN.

  - by EagerToLearn

  I'm in the process of adding a second DC to our domain and just want to make sure I have all the steps right before proceeding. Info: DC1 is 2008 R2 Standard. DC2 is 2008 R2 Standard. Network1 is 192.168.39.x/24 Network2 is 10.0.0.x/24 VPN is Sonicwall. The 2 DC's will be at two different sites, but the networks are connected by hardware VPN. (Sonicwall). The main DC server will be on the 192.168.39.0/24 network. The 2nd DC will be on 10.0.0.0/24. Here are the steps I plan to take; please let me know if I'm missing anything. Part 1: AD Sites and Services on DC1, create a new site and subnet for DC2. (Or should I create a new one for both?) (Can I use the default IPSiteLink and not change anything in there other than refresh timer?) Part 2: Point the DNS of DC2 to DC1. Run /forestprep and /domainprep (on both, or just DC1?). Dcpromo and select "Additional Domain Controller for Existing Domain". Then continue with normal steps with default locations for databases. EDIT: Didn't realize this was like reddit and required two skipped lines to skip one :P EDIT 2: When DCPromo-ing DC2, do I need to have "Append primary and connection specific DNS" and "Append parent suffixes of the primary DNS suffix" checked?

  Read the article

• Things to check for an internet-facing email server.

  - by Shtééf

  I'm faced with the task of setting up a public-internet-facing email server, that will be relaying mail for all of our other servers in the network. While the software in itself is set up in few keystrokes, what little experience I have with managing an email server has thought me that there are tons of awkward filtering techniques employed by other email systems. Systems that my own server will inevitably interact with a some point. Hence, my questions: What things should be kept in mind and double checked when setting up an email server? What resources are available for checking if my email server is set-up correctly? I'm specifically NOT looking for instructions for any given mail server, such as Exchange or Postfix. But it's okay to say: “you should have X and Y in your set-up, because when talking to server software Z, it typically tries to weed out open relays by checking for these.” Some things I've discovered myself: Make sure forward and reverse DNS are set up. Mail servers tend to do a reverse lookup for the peer IP-address when receiving. Matching a reverse look up with a follow-up forward lookup is probably employed to weed out open relays run through malware on home networks. Make sure the user in the From-address exists. The From-address is easily spoofed. A receiving mail server may try to contact the mail server in the From-domain, and see if the From-user actually exists.

  Read the article

• How to setup port forwarding from my Webserver (apache) to my Database server (mysql)

  - by karman888

  Hello again guys, and thank you for your help so far. Here is my problem: I have two remote dedicated servers, one webserver that runs apache, and one db server that runs mysql. The apache server is visible on the internet of course, but the second server is only visible to the apache server because they are connected with LAN. I need to connect to the remote mysql server through internet from my home-pc , but only apache server is visible to my home-pc. How can i setup port-forwarding from my apache server to the mysql server so i will be able to "see" the mysql server from my home-pc? This question is a follow-up from my first question Connect to remote mysql server from my application. Problem is that Mysql server is on LAN in which you answered me and helped me a lot by telling me to do "port-forwarding". I looked over the internet, and i cant find a good how-to to do port-forwarding. I'm an experienced programmer, but have little experience on hardware and networks. I can understand though what must be done, so i just need a litle help to sort things out :) I hope you can help me guys, Thank you in advance p.s. machine that Apache is running is on CentOS, mysql server also CentOS. p.s2 webserver runs WebHostManager i dont know if that makes any difference or it can be made easily through this, i just mention it :)

  Read the article

• ProCurve ACL to prevent a subnet from leaving the switch

  - by kce

  I have a single HP ProCurve 2610 in a remote location that is connected in with the rest of the network via SHDSL. There are two Layer-3 networks on this segment. ACLs are setup to deny one subnet (192.0.2.0/24) from ever being able to leave the switch by virtue of being applied to port attached to the upstream connection. The other subnet should be permitted to freely leave the switch. Both subnets are on the same VLAN. Unfortunately SFlow very clearly show broadcast traffic from 192.0.2.0/24 on the upstream connection. ProCurve ACLs are not my strong suit but I feel like I'm missing something very simple here. ip access-list extended "Filter for Camera Network" deny ip 192.0.2.0 0.0.0.255 0.0.0.0 255.255.255.255 log permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 exit interface 24 name "DSL - UPLINK" access-group "Filter for Camera Network" in exit Unless I am mistaken traffic from 192.0.2.0/24 should be dropped as it crosses the uplink port (int 24) whereas all other traffic will be permited by the following default allow rule. What exactly am I missing here? EDIT: Firstly, why do you have two subnets contained in the same VLAN? Because that's how it was configured by a previous administrator and while it makes conceptual sense that a single subnet is "mapped" to a single VLAN there's no technical constraint that I am aware of that makes this have to be the case. Instead of filtering inbound traffic on your uplink, you should be filtering outbound traffic. The HP2600 series can only filter inbound traffic on interfaces. Should I change my filter to deny any to 192.0.2.0/24?

  Read the article

• Windows 7 remote desktop encryption error every few minutes

  - by rfrankel

  Because of an error in data encryption, this session will now end. This is the error I've been getting more and more frequently over the past few days, to the point that I can't ignore it because it's happening consistently within 5 minutes of connecting - sometimes within a few seconds. Both the remote and local machines are Windows 7 Pro x64. The remote machine is behind a Linksys RV082, and I'm using UPnP to forward a remote port to the correct local port. This setup had been working fine for several months, and I can't think of any recent relevant changes that might have been made. Things I've already tried: Disabling unnecessary components of the network connection on the remote machine, until only IPv4 and Client for Microsoft Networks remain. Disabling TCP large send offload on both the remote and local machines. Confirming that the remote machine is not mentioned anywhere in any DMZ settings on the Linksys router. Confirming that there are no x509-related registry keys screwing things up (this is the suggested fix for a slightly different error anyway). These are the only solutions I've been able to find after about an hour of searching, and most of them apply to XP or Server 2003 in any case. If anyone could suggest something else, it would be much appreciated.

  Read the article

• Windows VPN always disconnects after < 3 minutes, only from my network

  - by hemp

  First, this problem has existed for almost two years. Until serverfault was born, I pretty much gave up on solving it - but now, hope is reborn! I've set up a Windows 2003 server as a domain controller and VPN server at a remote office. I am able to connect to and work over the VPN from every windows client I've tried, including XP, Vista, and Windows 7 without issue, from at least five different networks (corporate and home, domain and non.) It works fine from all of them. However, whenever I connect from clients on my home network, the connection drops (silently) after 3 minutes or less. After a short while, it will eventually tell me the connection has dropped and attempt to redial/reconnect (if I've configured the client that way.) If I reconnect, the connection will re-establish and appear to work correctly, but again will silently drop, this time after a seemingly shorter time period. These are not intermittent drops. It happens every single time, in exactly the same way. The only variable is how long the connection survives. It doesn't matter what type of traffic I send. I can sit idle, send continuous pings, RDP, transfer files, all of that at once - it makes no difference. The result is always the same. Connected for a few minutes, then silent death. Since I doubt anyone has experienced this exact situation, what steps can I take to troubleshoot my evanescing VPN?

  Read the article

• Cisco ASA user authentication options - OpenID, public RSA sig, others?

  - by Ryan

  My organization has a Cisco ASA 5510 which I have made act as a firewall/gateway for one of our offices. Most resources a remote user would come looking for exist inside. I've implemented the usual deal - basic inside networks with outbound NAT, one primary outside interface with some secondary public IPs in the PAT pool for public-facing services, a couple site-to-site IPSec links to other branches, etc. - and I'm working now on VPN. I have the WebVPN (clientless SSL VPN) working and even traversing the site-to-site links. At the moment I'm leaving a legacy OpenVPN AS in place for thick client VPN. What I would like to do is standardize on an authentication method for all VPN then switch to the Cisco's IPSec thick VPN server. I'm trying to figure out what's really possible for authentication for these VPN users (thick client and clientless). My organization uses Google Apps and we already use dotnetopenauth to authenticate users for a couple internal services. I'd like to be able to do the same thing for thin and thick VPN. Alternatively a signature-based solution using RSA public keypairs (ssh-keygen type) would be useful to identify user@hardware. I'm trying to get away from legacy username/password auth especially if it's internal to the Cisco (just another password set to manage and for users to forget). I know I can map against an existing LDAP server but we have LDAP accounts created for only about 10% of the user base (mostly developers for Linux shell access). I guess what I'm looking for is a piece of middleware which appears to the Cisco as an LDAP server but will interface with the user's existing OpenID identity. Nothing I've seen in the Cisco suggests it can do this natively. But RSA public keys would be a runner-up, and much much better than standalone or even LDAP auth. What's really practical here?

  Read the article

• NAT and P2P router crash

  - by returnFromException

  So..i had this argument with my networks teacher. He said that some people complains about router crashes due to many entrys on NAT tables on a router. I didnt understand and i asked: "If the application uses the same port, why does the router crash?. It should have only one entry (pc-ip,pcport;public-ip,public-port)". And he said: "it doesnt matter its using the same port". I got the idea that NAT creates an entry for every packet that passes trought it. Iam assuming NAT with overloading as you might have guessed. So the questions are: 1-How does nat entrys are created? On a packet basis or connection basis? I mean: suppose i send a udp packet..does the router create an entry? 2-When i start a TCP connection, does the router create a persistant nat entry until the connection closes? 3-Was my teacher right? The NAT table can overload assuming an aplication on the same port sending packets? Thanks in advance.

  Read the article

• Moving a site from IIs6 to IIS7.5

  - by Sukotto

  I need to move a site off of IIS6 (Win Server 2003) and onto IIS7.5 (Win Server 2008) as soon as possible. Preferably tomorrow. The site itself is a delightful mix of classic asp (vbscript) and one-off asp.net (C#) applications (each asp.net app is in its own virtual dir and has a self-contained web.config). In case it's relevant, this is a sort of research site made up of 40 or 50 unconnected microsites. Each microsite is typically a simple form allowing a user to submit a form, which then runs a Stored Proc on a sqlserver db and displays a chart and/or table of the results. There is very little security to worry about. The database connection info is in a central file (in the case of the classic asp) or app's individual web.config (lots of duplication there) To add a little spice to the exercise... I have no idea how to admin IIS The company no longer employs the sysadmin or the guys who set this thing up. (They're not going to employ me much longer either but my sense of professional pride does not permit me to just walk away from this task). The servers are on mutually firewalled networks and I have to perform a convoluted, multi-step process to copy anything from one to the other. Would someone please point me to a crash-course tutorial for accomplishing the above? I have: a complete copy of the site's filesystem on the new box installed the 3rd party charting tool on the new system a config.xml file from the "all tasks - save configuration to a file" right click menu. There doesn't seem to be a way to import it on the new system however. The newer IIS manager has a completely different UI and I'm totally lost. Please help.

  Read the article

• tomcat vs FULL J2EE Solutions

  - by jrhickey

  We are getting ready to make a major revision in our Web Application architecture which currently is running on JBoss 4.2. At first we were looking at moving from 4.2 to JBoss 6 but after some research tomcat may be a better solution for us. My first question is their anything that JBoss can do that tomcat cannot do assuming you are using the correct plugins. We do not really use EJB's in our solution and it would appear there are simple plugins for web services, JMX and other features. Tomcat appears to have much better support, faster upgrade cycles and many, many books. Since there is less to the system it also seems much easier to support from an admin point of view. What am I missing? The main features we want to enable are better clustering support and session replication / persistence. We will consider other application servers as well such as Glassfish / Geronimo. quote form a web article: Apache Tomcat is the world’s most widely used web application server, with over one million downloads per month and over 70% penetration in the enterprise datacenter. Tomcat is used to power everything from simple one server sites to large enterprise networks.

  Read the article

• What's the best way to telnet from a remote Windows PC without using RDP?

  - by Rob D.

  Three Networks: 10.1.1.0 - Mine 172.1.1.0 - My Branch Office 172.2.2.0 - My Branch Office's VOIP VLAN. My PC is on 10.1.1.0. I need to telnet into a Cisco router on 172.2.2.0. The 10.1.1.0 network has no routes to 172.2.2.0, but a VPN connects 10.1.1.0 to 172.1.1.0. Traffic on 172.1.1.0 can route to 172.2.2.0. All PCs on 172.1.1.0 are running Windows XP. Without disrupting anyone using those PCs, I want to open a telnet session from one of those PCs to the router on 172.2.2.0. I've tried the following: psexec.exe \\branchpc telnet 172.2.2.1 psexec.exe \\branchpc cmd.exe telnet 172.2.2.1 psexec.exe \\branchpc -c plink -telnet 172.2.2.1 Methods 1 and 2 both failed because telnet.exe is not usable over psexec. Method 3 actually succeeded in creating the connection, but I cannot login because the session registers my carriage return twice. My password is always blank because at the "Username:" prompt I'm effectively typing: Routeruser[ENTER][ENTER] It's probably time to deploy WinRM... Does anyone know of any other alternatives? Does anyone know how I can fix plink.exe so it only receives one carriage return when I use it over psexec?

  Read the article

• Can't access shared folder of win8/win7 machine - Error code: 0x80004005. Unspecified Error

  - by ruslan

  It's ironic that I, software engineer with 12 years of experience, continue to have this problem from one version of Windows to another without being able to achive consistent result (sometimes it works). Here it goes again. I have a machine with Win8 Consumer Preview. It doesn't really matter that it's win8. I had same issue with win7 before. On given machine I created local admin user with same name and password I have on second PC (the machine I'm typing this from now). I have two questions to you guys. Why I'm not able to access C$ share of win8 machine from another Win7 machine? I get error that C$ doesn't exist even though it does. Why I'm not able to access share named "test" in Win8 for which Permission set to Full for Everyone. When I attempt to access it from Win7 machine I'm asked to enter username and password. After entering administrator credentials I get error "Windows cannot access \192.168.1.123\test. Error code: 0x80004005. Unspecified Error". Windows Firewall is disabled on Win8 machine for both Private and Public networks. Guest account is disabled. Built-in admin account is enabled. Machine is pingable from other machines.

  Read the article

• Primary/secondary ethernet interfaces in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local...

  Read the article

• Measure Upload Speed between a client and our server

  - by tresstylez

  We host a SAAS application specially customized for multiple clients. For one customer in particular -- they are reporting sporadic performance issues from various locations on their network, in particular UPLOADING documents through a form on our website. The client claims they have "bandwidth to spare" and that utilization of their "pipe" is so low that it MUST be our application, but our application has MANY clients and all features are working fine for all other clients. Interestingly enough -- DOWNLOADS (ie. just accessing the website, or downloading documents) is working fine. Speed test shows that they should get 1.2Mbps UP. So, a 3MB file should take 20 secs to upload. It takes 60+ seconds on their network. Sometimes even small files take OVER 10 minutes to upload or they timeout. Pings and Traceroutes don't show any abnormally long hops or response times. They claim other SAAS applications they use allow them to upload just fine. Both IT teams are working together to resolve this issue. What kind of data can I request from the clients to begin ruling things out. Seems like we need to somehow measure LATENCY of the networks involved or even at the switch level, we need to understand if packets are getting dropped somewhere and why. Where should I start? Any help is appreciated. I'll provide more info upon requests

  Read the article

• Trouble with Russian pc's on my wifi

  - by hogni89

  I have created a WiFi hotspot for the local community. The problem is, some Russian PC's (Windows XP, Windows Vista and Windows 7) can't get internet connection (We have a lot of bypassing russian fishing vessels / cargo ships). The pc's obtain a valid IP address, and some of them can even manage to send some few packages - But none of them are usable on the network. They all say "Limited internet access" or "???????????? ?????? ? ????????". The thing these PC's have in common is, that they all run a Russian installation of Windows. No one else has problems with the WiFi hotspot - Danish and English Windows, Linux and OS X all work like a charm. Can it be, that there is a difference between the danish / english windows installation, compared to the Russian installation? EDIT START They can't ping the router (One PC got one response - ONCE), they can't access any sites and Windows newer asks "Is this network public, home or work?". EDIT END PS: The hotspot is a airMAX rocket M from Ubiquiti Networks, Inc (www.ubnt.com)

  Read the article

• Offloading backups to secondary network

  - by user1467163

  I'm trying to solve a problem- Currently, we are constantly backing up and have no budget for additional servers. Our production network is still a 10/100 and handles voip, SQL plus our backup traffic, and I'd like to offload the backup traffic onto a secondary network- all of our servers have secondary NIC's that are not in use, and all support gigabit (Our switching hardware does not- a topic for another day). I'd like to move my backups off the production network, but I am having a hard time getting the computers to communicate. I am using a Netgear GS724T switch for the backup network- Chosen for cost and because I have used them extensively on networks saturated with ghosting traffic, so I know it's up to the task. I have defined a VLAN, with ports that are not members of any other VLAN. All traffic is untagged on the VLAN. I have set the servers with 192.168.1.10 and 192.168.1.11 addresses, 255.255.255.0 netmask and I have tried a blank GW, using the local IP of the server 192.168.1.whatever address, and I have tried using the switch's production-side IP as the GW. The machines cannot find each other. DNS addresses are blank because I am going purely by IP for now... Any ideas how to get these machines to talk? they are Windows machines, running Server 2008R2 and 2003R2. Thanks!

  Read the article

• Remote network traffic not passing through VPN

  - by John Virgolino

  We have the following topology: LAN A LAN B LAN C 10.14.0.0/16 <-VPN-> 10.18.0.0/16 --- SONICWALL <-VPN-> M0N0WALL --- 10.32.0.0/16 Traffic between LAN A and LAN B works perfectly. Traffic between LAN C and LAN B works perfectly. Traffic between LAN A and LAN C, not so much. LAN A's gateway has a route to LAN C that points to the Sonicwall. The Sonicwall has a route to LAN A pointing to the VPN gateway connecting LAN B to LAN A. Tracing packets on the Sonicwall shows the LAN C destined traffic to arrive on the Sonicwall, but it does not forward the traffic, it dies there. Traffic from LAN B gets forwarded. Tracing packets on the Sonicwall while sending traffic from LAN C destined for LAN A shows nothing. This tells me that the M0N0WALL is not forwarding traffic for the 10.14.0.0 network and the Sonicwall is not forwarding from 10.14.0.0. The SA on the Sonicwall terminates on the WAN ZONE and is defined to use an address group that incorporates both the 10.14.0.0 and 10.18.0.0 networks. The M0N0WALL is configured for the 10.18.0.0 network and I have tried with both a static route to 10.14.0.0 and without on the M0N0WALL. I tried manually adding the 10.14.0.0 network to the SA on the M0N0WALL, but that really aggravated it and the SA never came up, so I reverted. I have checked all the firewall rules to make sure nothing is blocked. All of the Sonicwall auto-added rules look right. Specs: Sonicwall TZ200, Enhanced OS M0N0WALL v1.32 I'm at a loss at this point. Any help would be appreciated.

  Read the article

• Configure linux machine as bridge/switch and end device

  - by leemes

  At my home, I have two desktop PCs in two rooms. The router / DSL modem is in one of these rooms. Now I want to configure a home server (having 2 LAN ports, running 24/7) in the corridor between the two rooms, using only one LAN cable at each door. This gives me the following physical configuration: (door) (door) .----/-/----. .-----/-/----------._ FritzBox | | | .----´´ DSL Router PC1 Server | PC2 As just said, the server has 2 network interfaces and is running Ubuntu. What I need now is a network configuration which enables both the server and PC1 to connect to the router. I think the server needs to serve as a bridge or switch. Currently, all computers are configured having static IP addresses. If I'm understanding it correctly, a bridge / switch doesn't have its own IP address, but as the server needs to be configured as an own end device, it needs to have one. My first question is, do I have to configure both interfaces separately, giving both the same static IP address? My next question is, how do I bridge the two physical networks into one? I have basic understanding (but am always confused again and again) of bridges and switches, but I don't know how to configure it in software. I only know that it's possible to do so :) The third question is: Is it possible to configure this in a way that network packets from/to PC1 to/from the router only go through hardware or only consume low CPU in the server? Can you help me? Thanks in advance!

  Read the article

• Linux will not activate wireless after device has been re-enabled

  - by XHR

  Using a Eee 900A netbook by Asus. By pressing Fn + F2, I can disable or enable the wireless chip on the netbook, a blue LED indicates the status. I've been able to connect to wireless networks just fine with this netbook. However, if the wireless chip ever becomes disabled, I have to reboot to get my network connection back. This generally happens when suspending. For some reason the LED will be off and I have to hit Fn + F2 for it to light up again. However, after doing so, Linux will not reconnect to the network. It simply changes the wireless status from "wireless is disabled" to "device not ready". Even worse, I've recently had issues with the chip being enabled at boot, thus making it nearly impossible to get connected. I've searched around on-line but haven't found much of anything useful on this. This happens on all kinds of different distros including Ubuntu 9.10 Netbook, EeeBuntu 4 beta, Jolicloud and Ubuntu 10.04 Netbook. Edit I noticed this question is getting a lot of views. To give a quick update, I never did resolve this issue with the given distro's. However, I'm currently running Ubuntu 10.10 netbook edition and this issue has gone away.

  Read the article

• Multi- authentication scenario for a public internet service using Kerberos

  - by StrangeLoop

  I have a public web server which has users coming from internet (via HTTPS) and from a corporate intranet. I wish to use Kerberos authentication for the intranet users so that they would be automatically logged in the web application without the need to provide any login/password (assuming they are already logged to the Windows domain). For the users coming from internet I want to provide traditional basic/form- based authentication. User/password data for these users would be stored internally in a database used by the application. Web application will be configured to use Kerberos authentication for users coming from specific intranet ip networks and basic/form- based authentication will be used for the rest of the users. From a security perspective, are there some risks involved in this kind of setup or is this a generally accepted solution? My understanding is that server doesn't need access to KDC (see Kerberos authentication, service host and access to KDC) and it can be completely isolated from AD and corporate intranet. The server has a keytab file stored locally that is used to decrypt tickets sent by the users coming from intranet. The tickets only contain username and domain of the incoming user. Server never sees the passwords of authenticated users. If the server would be hacked and the keytab file compromised, it would mean that attacker could forge tickets for any domain user and get access to the web application as any user. But typically this is the case anyway if hacker gains access to the keytab file on the local filesystem. The encryption key contained in the keytab file is based on the service account password in AD and is in hashed form, I guess it is very difficult to brute force this password if strong Kerberos encryption like AES-256-SHA1 is used. As the server has no network access to intranet, even the compromised service account couldn't be directly used for anything.

  Read the article

• Outdoor WiFi Mesh Topology vs. Repeaters

  - by IronJaxor

  Here's the current configuration in our organization (which I believe is incorrect): We have a number of Cisco 1500 series AP's (22 in total), that are mounted outdoors to provide seamless WiFi coverage over a large area. Each AP however has its own physical ethernet connection back to the WLC (All the AP's are marked as Root AP's). They are all broadcasting the same SSID. We have tried to stagger the channel selection but because there are only three non-overlapping channels to choose from, and in some areas the density of AP's is quite high, there is multiple places of channel interference. With this configuration we experience 100-150 disconnects from clients every day. (Our clients are mobile so they move throughout the coverage area constantly). My idea is to switch the AP's to the same channel thereby forming a wireless mesh, use the built in functionality of the 1500 series to use 802.11a as the backhaul, designate one or two AP's as root AP's and wire them back to the WLC. Thereby forming a WiFi mesh, which if I'm not mistaken is the point of the 1500 series in the first place! I am however completely new at WiFi networks and wondering if I am simply mistaken in what I believe my proposed changes will enable, or if there is a better way to tackle the WiFi topology.

  Read the article

• Network structure --> Server 2k8r2 <--> Livebox <--> Router <--> Other PCs

  - by Yusuf

  I have a Livebox connection to the Internet and I have set up my network as follows: - Livebox <--> Win2k8R2 Server - Livebox <--> Netgear N150 Router - Router <--> Other PCs Therefore, in my LAN, - the Livebox has IP address 192.168.1.1, - the Router 192.168.1.12 (when accessed from the Livebox or the server), - the Router 10.0.0.1 (when accessed from the PCs connected to the Router), - the server 192.168.1.2, - the PCs 10.0.0.x I was using a previous configuration, which was as follows: - Livebox <--> Netgear N150 Router - Router <--> Win2k8R2 Server - Router <--> Other PCs Everything was simple, and I just had to forward all ports for incoming connection on the Livebox to the Router, and then forward the specific ports to the Server as needed (it must be however noted that any server I use is found on the Win2k8R2 server itself). In this previous configuration, the IP addresses were as follows: - Livebox 192.168.1.1 - Router 192.168.1.12 (when seen from Livebox) - Router 10.0.0.1 (when seen from server & PCs connected to it) - Server 10.0.0.2 - PCs 10.0.0.x So now of course, my port-forwarding does not work anymore since the server is not connected (directly) to the Router. What I would like to know is how do I configure the Livebox and Router to still have the features like before? From what I understand of networks (which is very limited, btw), I see these options: Make the router assign IPs like 192.168.1.x (but then I want the forwarding to be done from the router itself, is it possible?) The forwarding on the router to the server uses IP address 10.0.0.2. I could change it to 192.168.1.2 (Is that even possible, does it work?) Forward all ports from the Livebox itself to the server, and then manage them there (Is software-based port-forwarding as secure as hardware-based?)

  Read the article

• VMware Workstation Bridged Network Host UnReachable

  - by user2097818

  VMware Workstation 7 on Win7-64 (Home Premium). I have confirmed this on any guest running on this machine (from winxp to debian). I am using a bridged network connection for my guests (Automatic on VMnet0). All of the network configuration is done with DHCP (including on the host). Problem What I can not do: Ping my host machine from inside any VM. (either shows me "Destination Host Unreachable" or will just timeout) What I CAN do right after power up, with no problems at all. I can connect to the internet from inside the VM I can ping my router from inside the VM I can ping other machines on my network from inside the VM Other machines can ping the VM Other machines can ping the host My host machine can ping the VM (this one is important. read further) Details So I have my router assigned as 192.168.2.1/255.255.255.0, and the router provides the DHCP service (and it seems to be doing so successfully). There are no IP conflicts on the network that I am aware of. All Gateways and Subnet masks are appropriate and matching. My entire workshop is on one single subnet, with one single DHCP server and gateway. There is one method in which I can ping successfully, but it requires an active connection initiated from the host (I start pinging from host to VM). During the period of the active connection, I can successfully ping from VM to host, using explicit IP address. As soon as the host connection is closed, the VM ping starts hanging with the same old messages. My Thoughts This really feels like a firewall problem, but I have turned off all firewalls on host and VM, powered down the network, powered back up, and the problem still persists. And if it was firewall, why would only the IP address associated with bridged VM networks be blocked. I feel as though my host operating system (Win7) is somehow configured incorrectly, or, VMware Workstation is configured incorrectly from the host side. Although I have done my best to put everything in default, I feel like I am missing something silly.

  Read the article

< Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >