Search Results

Search found 5286 results on 212 pages for 'logs'.

Page 157/212 | < Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >

• PowerConnect 3548p SNTP and web interface not working

  - by Force Flow

  I have been unable to get SNTP and access to the web interface working properly on a Dell PowerConnect 3548p. In the logs, this message appears over and over again: 04-Jan-2000 20:19:29 :%MNGINF-W-ACL: Management ACL drop packet received on interface Vlan 172 from 172.17.0.3 to 172.18.0.10 protocol 17 service Snmp 172 is the management vlan. 172.17.0.3 is the DNS server 172.18.0.10 is the switch's IP address. The DNS server and the switch are located on different subnets and separated by routers. I am unable to access the web interface of the switch from the 172.17.x.x subnet. I can only access the web interface of the switch if I am accessing it from the 172.18.x.x subnet. There is also a managed linksys switch on the 172.18.x.x subnet on the 172 vlan, which has no problem with SNTP. I can also access it from the 172.17.x.x network. So, it stands to reason that this is not a firewall or routing issue, but with the 3548p switch. I suspect the issue is with management permissions/ACLs on the 3348p switch, but that's about as much as I've been able to determine so far. Any ideas?

  Read the article

• Apache2 VirtualHosts 403 Oddity

  - by Carson C.

  I'm sure this is something I should already understand, but I'm finding myself confused. The configs in play add up to this: NameVirtualHost *:80 Listen 80 <VirtualHost *:80> <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Deny from all </Directory> </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] ServerName domain.tld ServerAlias *.domain.tld DocumentRoot /var/www/domain.tld <Directory /var/www/domain.tld> Options -Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> DNS is working correctly. The issue is, every variant of http://*.domain.tld/ (including http://domain.tld/) works correctly, except http://www.domain.tld/ which throws a 403. The logs state: client denied by server configuration: /etc/apache2/htdocs If I remove the first VirtualHost block from play, everything works as expected including http://www.domain.tld. This leads me to believe that for some reason, Apache is not considering www.domain.tld to match the second VirtualHost block, and is thereby falling back to deny all. This seems wrong. Shouldn't the second block match www.domain.tld? I've been able to resolve this, but I still don't understand why. In my original configs, I was using the real ip address of the server instead of *. Switching all instances to * as shown above made everything work as expected. Does this have something to do with the way browsers request resources?

  Read the article

• Revover original email from Sendmail log

  - by Xavi Colomer

  I have a website the contact form has been failing silently for two weeks (Wordpress + Contact form 7). Apparently updating to Contact Form 7 made the assigned email to fail [email protected], I also tested with [email protected] and it also failed until I tried with gmail and it finally worked. Apparently @telefonica.net and @me.com domains are not working with this version of the plugin, but I have to investigate the cause. I found the logs of the lost emails, but I would like to know If I can recover the sender or the content of the original messages. May 24 23:41:11 localhost sendmail[27653]: s4P3fBc3027653: from=www-data, size=3250, class=0, nrcpts=1, msgid=<[email protected]_web.com>, relay=www-data@localhost May 24 23:41:11 localhost sm-mta[27655]: s4P3fBdA027655: from=<[email protected]>, size=3359, class=0, nrcpts=1, msgid=<[email protected]_web.com>, proto=ESMTP, daemon=MTA-v4, relay=localhost.localdomain [127.0.0.1] May 24 23:41:11 localhost sendmail[27653]: s4P3fBc3027653: [email protected], ctladdr=www-data (33/33), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=33250, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (s4P3fBdA027655 Message accepted for delivery) May 24 23:41:12 localhost sm-mta[27657]: s4P3fBdA027655: to=<[email protected]>, ctladdr=<[email protected]> (33/33), delay=00:00:01, xdelay=00:00:01, mailer=esmtp, pri=123359, relay=tnetmx.telefonica.net. [86.109.99.69], dsn=5.0.0, stat=Service unavailable May 24 23:41:12 localhost sm-mta[27657]: s4P3fBdA027655: s4P3fCdA027657: DSN: Service unavailable May 24 23:41:12 localhost sm-mta[27657]: s4P3fCdA027657: to=<[email protected]>, delay=00:00:00, xdelay=00:00:00, mailer=local, pri=30000, dsn=2.0.0, stat=Sent Thanks

  Read the article

• What could cause an 101 Error in WAMP under Windows 7 ?

  - by Brayn

  Hey, I'be been using WAMP for local development for quite a while now but lately I've been getting an Error 101 message when I browse localhost sites. It's possible for this to have appeared after the last WAMP update but I'm not 100% sure on this. If I try again and again, after several page refreshes it works but it's really annoying! The exact error message is: Error 101 (net::ERR_CONNECTION_RESET): Unknown error. This is my configuration: OS: Windows 7 Apache: 2.2.11 PHP: 5.2.9-2 WAMP: 2.0 Also the local scripts connect to a remote MySQL server, they don't use the local MySQL(I don't know if it matters, just though I let you know). I've been looking into the apache logs and I've found the following. It seems that the apache server keeps restarting and I can't figure why: [Wed Oct 14 13:52:30 2009] [notice] Parent: child process exited with status 255 -- Restarting. [Wed Oct 14 13:52:30 2009] [notice] Apache/2.2.11 (Win32) PHP/5.2.9-2 configured -- resuming normal operations [Wed Oct 14 13:52:30 2009] [notice] Server built: Dec 10 2008 00:10:06 [Wed Oct 14 13:52:30 2009] [notice] Parent: Created child process 6784 [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Child process is running [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Acquired the start mutex. [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Starting 64 worker threads. [Wed Oct 14 13:52:31 2009] [notice] Child 6784: Starting thread to listen on port 80. [Wed Oct 14 13:52:32 2009] [notice] Parent: child process exited with status 255 -- Restarting. [Wed Oct 14 13:52:33 2009] [notice] Apache/2.2.11 (Win32) PHP/5.2.9-2 configured -- resuming normal operations [Wed Oct 14 13:52:33 2009] [notice] Server built: Dec 10 2008 00:10:06 [Wed Oct 14 13:52:33 2009] [notice] Parent: Created child process 3572 [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Child process is running [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Acquired the start mutex. [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Starting 64 worker threads. [Wed Oct 14 13:52:33 2009] [notice] Child 3572: Starting thread to listen on port 80. Also I've checked Windows Firewall and disabled any other protection that I have on this computer with no improvement. Thanks!

  Read the article

• Problem with Outlook 2010 (SMTP AUTH LOGIN)

  - by Filipe YaBa Polido

  **IGNORE THIS QUESTION - SOLVED WITH A PYTHON SCRIPT available at: http://yabahaus.blogspot.com I have to connect one customer Outlook 2010 to a remote server on which I have either no right, neither way to talk to the sysadmin. This is the thing, after installing and reviewing the logs on Wireshark: Outlook Express: HELO machine AUTH LOGIN username base64 encoded password base64 encoded mails go through. Outlook 2010: HELO machine AUTH DIGEST-MD5 response from server Outlook sends just a * AUTH LOGIN password base64 encoded So... I can send mails in the same domain, but can't send outside, it gives me a relay denied message. My point is... Why the h**l Outlook 2010 doesn't send the username AND the password?! It can never login the right way :| With other versions of Outlook it works fine, and with OE works great, it auths and allows to send mail to a different domain. I've googled and nothing worked. I'm pretty sure that I'm not alone with this one. My last resort will be to configure a local proxy/server that relays to the original one :| Any help would be appreciated. Sorry my bad english as is not my natural language. Thanks.

  Read the article

• AFP/SSH stopped working on OS X Server

  - by churnd

  I have 3 Mac OS X servers all bound to AD, all configured in the Golden Triangle setup. All 3 are completely separate from each other in terms of services, but all reside on the same internal network and are all bound to the same Active Directory domain. Two are 10.5.x (latest updates) and one is 10.6.3. Last weekend, all 3 simultaneously stopped allowing Active Directory users access to certain services, specifically AFP & SSH. SMB still works fine on all 3. I asked the AD admin if anything changed, and he said "Yes, we made a change to user accounts to toughen up security", and suggested I use [email protected] instead of just username. This still didn't work. I have completely removed one of my servers from AD, and re-joined, but this didn't work either. I can do kinit from command line and get a Kerberos ticket. sudo klist -ke shows all services are configured to use the correct Kerberos principles. I have been scavenging the logs for any useful info. The AFP log just shows that I'm connecting and disconnecting. The DirectoryService.log shows stuff about misconfigured Kerberos hashes, but my research is showing that's not uncommon. /var/log/system.log isn't showing anything useful that I can see. I'm not sure where to go from here. Any help/ideas appreciated.

  Read the article

• IP tables blocking access to most hosts but some accesses being logged

  - by epo

  What am I getting wrong? A while back I locked down my web hosting service while hardening it or at least trying to. Apache listens on port 80 only and I set up iptables using the following: IPS="list of IPs" iptables --new-chain webtest # Accept all established connections iptables -A INPUT --protocol tcp --dport 80 --jump webtest iptables -A INPUT --match state --state ESTABLISHED,RELATED --jump ACCEPT iptables -A webtest --match state --state ESTABLISHED,RELATED --jump ACCEPT for ip in $IPS; do iptables -A webtest --match state --state NEW --source $ip --jump ACCEPT done iptables -A webtest --jump DROP However looking at my apache logs I notice various log entries in access_log, e.g. 221.192.199.35 - - [16/May/2010:13:04:31 +0100] "GET http://www.wantsfly.com/prx2.php?hash=926DE27C156B40E55E4CFC8F005053E2D81E6D688AF0 HTTP/1.0" 404 206 "-" "Mozilla/ 4.0 (compatible; MSIE 6.0; Windows NT 5.0)" 201.228.144.124 - - [16/May/2010:11:54:16 +0100] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 226 "-" "-" 207.46.195.224 - - [16/May/2010:04:06:48 +0100] "GET /robots.txt HTTP/1.1" 200 311 "-" "msnbot/2.0b (+http://search.msn.com/msnbot.htm)" How are these slipping through? I don't mind the indexing bots (though I am a little surprised to see them get through). I suppose they must be getting through using the ESTABLISHED,RELATED rules. And no, I can't for the life of me remember why the first match state rule is there So 2 questions: is there a better way to set up iptables to restrict access to specified hosts? How exactly are these 3 examples slipping through?

  Read the article

• Solaris Mysql Failure and Unable to Restart

  - by Iscariot

  Environment: Solaris 10 This mysql server has been up and running for 6 months now. Today all of a sudden it crashed. When typing 'mysql' as user it gives the error MYSQL" Error 2002 (HY000): Can't Connect to Local MySQL server though socket '/tmp/mysql.sock' when typing mysql as root it says mysql: not found. The server try to open mysql, it stays open for 9-10 seconds and restarts the process. Below are the application logs. Application-database-mysql_mysql-csk.log [ May 30 22:37:52 Enabled. ] [ May 30 22:37:58 Rereading configuration. ] [ May 30 22:37:59 Executing start method ("/opt/coolstack/lib/svc/method/svc-cskmysql start") ] /opt/coolstack/mysql/bin/mysqld_safe --user=mysql --datadir=/dbpool1/data --pid-file=/dbpool1/data/database.soliaonline.com.pid [ May 30 22:37:59 Method "start" exited with status 0 ] [ May 30 22:38:13 Stopping because all processes in service exited. ] [ May 30 22:38:13 Executing stop method ("/opt/coolstack/lib/svc/method/svc-cskmysql stop") ] [ May 30 22:38:13 Method "stop" exited with status 0 ] [ May 30 22:38:13 Executing start method ("/opt/coolstack/lib/svc/method/svc-cskmysql start") ] /opt/coolstack/mysql/bin/mysqld_safe --user=mysql --datadir=/dbpool1/data --pid-file=/dbpool1/data/database.soliaonline.com.pid [ May 30 22:38:13 Method "start" exited with status 0 ] [ May 30 22:38:25 Stopping because all processes in service exited. ] [ May 30 22:38:25 Executing stop method ("/opt/coolstack/lib/svc/method/svc-cskmysql stop") ] [ May 30 22:38:25 Method "stop" exited with status 0 ] I am hoping someone might have run into this before and might know how to fix it.

  Read the article

• Self-connecting printers

  - by Martin Cerny

  Hello, I work as an administrator in a small company using XP Professional on all computers and two servers with Win 2003 Server. Recently a very unusual problam occured one of the computers keeps connecting to all the printers on the network it doesn't matter if it's an administrator or Domain User as soon as somebody logs in the commputer connects all the printers. The printers are either installed on local computers or on the server and shared. There is no log-on script connecting the printers, I install them manualy and none of the other computers shows such behaviour. We have a printer which is installed on two computers and both of them share it (I'm moving it to Server from a small PC which shared it up to now, but some computers still use the old connection), meaning this specific computer connects to one of the printer two times and it can't use either of the connections. How to prevent this self-connecting to all printers (none of the other computers has this problem). If I delte them from the "Printers" folder everything works fine untill I reconnect and the Folder is once again full of all the printers we have. I solved the smaller problem, computer is now capable of printing on all of the printers (it seems there have been some registry issues), after cleaning the registry and reinstalling the printer it seems to work just fine. But the second thing prevails, the computer connects to all the printers in the network (when I remove one/multiple it is reconnected right after the next log-in by any user).

  Read the article

• if the file changes send email about diff

  - by user62367

  I have 2 script. Script "A", Script "B". Script A is regulary watching the dhcpacks [dhcp release is configured to 2mins] in the logs, for the past 2 minutes. It writes the MAC addresses to a file [/dev/shm/dhcpacks-in-last-2min.txt] every 2 minutes. Ok, this is working, active clients are in this file. Super! Script B: On pastebin I'm trying to create a script, that watches the changes in /dev/shm/dhcpacks-in-last-2min.txt file ( every 1 sec). Ok. But: my watcher script [the pastebined][1] is not working fine - sometime it works, sometime it sends that someoneXY logged out`, but it's not true! Nothing happened, and the problem is not in the Script A. Can someone help me point out, what am I missing? How can I watch a file (in every sec), that contains only MAC addresses, and if someone doesn't get dhcpack in 2 minutes, the file /dev/shm/dhcpacks-in-last-2min.txt changes, and that clients MAC address will be gone from it, and i need to know, who was it [pastebined my script - but somethings wrong with it]. Thank you for any help..I've been pathing my script for days now.. :\

  Read the article

• Virus cleanup; Windows Automatic Updates service crashes in esent.dll

  - by quack quixote

  Background I'm doing system recovery on an old WinXP SP1 system brought to me on suspicion of virus infection. After taking preliminary backups, I used MalwareBytes to detect and clean the infection. I might've even gotten it all. In the process, I've discovered (a) the system drive is showing signs of impending failure, and (b) the owner has been using the system's old crusty IE-6 instead of the up-to-date Firefox I've provided for him. So naturally, thinking I had a relatively stable system, I tried to hit the Windows Update site to install IE-8, in case further training doesn't stick. The update site told me it needed to update the installer, and I started that process. Soon after, wuauclt.exe started crashing, reporting addresses in module esent.dll. There's a Microsoft KB (910437) on a problem with that DLL, so I downloaded the hotfix and installed. The crashing did not stop. I attempted to install SP3 from the offline installer, but that didn't fix the issue either. The system is reporting a few hard drive / IDE controller errors, but they don't correlate to the crashes, so they aren't the direct cause. I've also attempted to rollback to the time between the infection removal and the first crashes, but that doesn't help. Question The hotfix I tried to install dealt with problem in transaction logs of the Extensible Storage Engine (ESE) database. I suspect this issue is similar, but that the database itself (whatever the ESE database is) is corrupted. Is there a way to clean or clear this database so that system operation returns to normal? Can someone enlighten me as to what the ESE database actually is, and where it resides? Can I just locate some files and delete them to bring this under control?

  Read the article

• IIS 7.5 truncating POST body containing JSON data with ASP.NET MVC 3

  - by Guneet Sahai

  I'm facing a problem which I hope is a configuration thing with IIS but is right now giving a lot of trouble. Basically I have a controller that accepts a JSON and does some processing. While it generally works fine, but every now and then when the system has some load I get an error. After some painful debugging, we figured the incoming JSON gets truncated which causes the deserialzer to fail. To narrow down the problem - we wrote a simple controller that accepts a JSON and tries to deserialize it. In case it fails it just logs it. This works fine but when I hit it using a load testing tool (JMeter) it throws the same error (truncation) for a few requests. The # of failures increased when I increase parallel connections. It starts showing with 150 concurrent requests. We are running IIS 7 on windows 2008 server with ASP.Net MVC 3 with more or less default configuration of IIS. More information available in my question below http://stackoverflow.com/questions/12662282/content-length-of-http-request-body-size

  Read the article

• Is this hard disk dead?

  - by Korjavin Ivan

  Not sure, is this right site for this Q, but let me try Last time i have problem with hard disk. Sometimes its do strange sound, and i get it from logs: $dmesg | grep ata4 [29409.945516] ata4.00: exception Emask 0x10 SAct 0xf SErr 0x90202 action 0xe frozen [29409.945529] ata4.00: irq_stat 0x00400000, PHY RDY changed [29409.945538] ata4: SError: { RecovComm Persist PHYRdyChg 10B8B } [29409.945546] ata4.00: failed command: READ FPDMA QUEUED [29409.945562] ata4.00: cmd 60/30:00:56:22:5f/00:00:00:00:00/40 tag 0 ncq 24576 in [29409.945573] ata4.00: status: { DRDY } [29409.945580] ata4.00: failed command: READ FPDMA QUEUED [29409.945594] ata4.00: cmd 60/18:08:8e:22:5f/00:00:00:00:00/40 tag 1 ncq 12288 in [29409.945605] ata4.00: status: { DRDY } [29409.945611] ata4.00: failed command: READ FPDMA QUEUED [29409.945625] ata4.00: cmd 60/08:10:46:02:66/00:00:00:00:00/40 tag 2 ncq 4096 in [29409.945635] ata4.00: status: { DRDY } [29409.945641] ata4.00: failed command: READ FPDMA QUEUED [29409.945656] ata4.00: cmd 60/80:18:ee:04:66/00:00:00:00:00/40 tag 3 ncq 65536 in [29409.945666] ata4.00: status: { DRDY } [29409.945679] ata4: hard resetting link [29413.976083] ata4: softreset failed (device not ready) [29413.976097] ata4: applying SB600 PMP SRST workaround and retrying [29414.148070] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [29414.184986] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd [29414.243280] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd [29414.243292] ata4.00: configured for UDMA/133 [29414.243324] ata4: EH complete [680674.804563] ata4: exception Emask 0x50 SAct 0x0 SErr 0x90a02 action 0xe frozen [680674.804575] ata4: irq_stat 0x00400000, PHY RDY changed [680674.804584] ata4: SError: { RecovComm Persist HostInt PHYRdyChg 10B8B } [680674.804603] ata4: hard resetting link [680678.840561] ata4: softreset failed (device not ready) Is this ata4 sata hard drive dead? Must i change it ASAP ? Need I specify more info?

  Read the article

• OS X superuser folders automatically created. Perusers launchd process appears to kill 501

  - by Ric Pen

  New Apple laptop OSX 10.8.2. I have used OS X but many years previously, and am not familiar with subtleties or changes in com.apple.launchd.peruser.x... I have previously (and in retrospect, foolishly) made changes to these rapidly spawned new peruser accounts (my initial reaction was that if ipfw was disabled, then I might well be under hacker attack, which I have dealt with, years ago), but I believe I was wrong, and the results of my efforts at preserving the system's integrity have in fact been destructive, overreactive, and have resulted in much work to restore. My understanding from other posts is that superuser protocols have changed quite dramatically since I bought the first developer version of OS X many years ago. Haven't developed on Apple much since then, w/ exception of WebObjects (IMO, much underrated at that time, and was more user friendly than ASP (prior to .NET, I vaguely recall). Creation of apparently nasty peruser folders appear to confound 501 process, which logs inability to find firewall (ipfw). Can someone help me with this? I am concerned that either the system is improperly configured, an application was improperly installed (although there is little here beyond Apple's SDK, which I find quite accommodating and intuitive). Still, I am a novice, only sporadically develop at this time, and would really just like to see this system running happily. Please offer assistance, in the form of potential info sources, or if you have had a similar experience, then perhaps scripts to suss out this issue. I do not wish to damage the system, but Apple's Developer connection and discussion threads do not appear to have dealt with this particular issue recently... Although I may well have missed something you have not - please apprise. Any assistance on this issue is very much appreciated - by an old guy, who wants to do some things which were fun about 20 years ago.

  Read the article

• Bacula virtual backup job doesn't run, no output?

  - by Zoredache

  I am trying to get Virtual Backups working, but when I try to run a virtual backup job, it appears to get created, but then never seems to actually run. I have a full, and a couple incremental backups. status director JobId Level Files Bytes Status Finished Name ==================================================================== 1283 Full 10,565 1.963 G OK 21-Dec-12 09:47 nms-Job 1284 Incr 314 129.6 M OK 21-Dec-12 09:49 nms-Job 1285 Incr 230 147.2 M OK 21-Dec-12 09:51 nms-Job 1288 Incr 525 138.8 M OK 21-Dec-12 11:25 nms-Job I attempt to start a job from bconsole like this. *run job=nms-Job level=VirtualFull Using Catalog "MySQL" Run Backup job JobName: nms-Job Level: VirtualFull Client: nms-FileDaemon FileSet: nms-FileSet Pool: nms-pool (From Job resource) Storage: File_d1 (From Pool resource) When: 2012-12-21 13:07:54 Priority: 10 OK to run? (yes/mod/no): Job queued. JobId=1291 Then my new job, just sits there, doing nothing. The JobStatus shows that the job was created, but it appears to never run? All the full, and incremental backups are terminating normally. *llist jobid=1291 JobId: 1,291 Job: nms-Job.2012-12-21_13.07.56_07 Name: nms-Job PurgedFiles: 0 Type: B Level: F ClientId: 4 Name: nms-FileDaemon JobStatus: C SchedTime: 2012-12-21 13:07:54 StartTime: 2012-12-21 13:07:56 EndTime: 0000-00-00 00:00:00 RealEndTime: 0000-00-00 00:00:00 JobTDate: 1,356,124,076 VolSessionId: 0 VolSessionTime: 0 JobFiles: 0 JobErrors: 0 JobMissingFiles: 0 PoolId: 19 PooLname: nms-pool PriorJobId: 0 FileSetId: 11 FileSet: nms-FileSet I am getting very frustrated, that this isn't working, mostly because it isn't giving me any error logs, or output at all. I submit the job, and as far as I can tell nothing happens. Is there some status, or debugging level that I can set to get a useful information about why this isn't working? What can I do to make this work? I was originally running Bacula 5.0.2 on Debian Squeeze, out of frustration, I upgraded to the 5.2.6 in the backports repository, hoping that a new version might give me better results.

  Read the article

• Server Crash Diagnosis...Are there any 'black box recorder' style programs available.

  - by columbo

  My redhat server is crashing every three weeks or so at 4:15am ish on Sunday mornings. (well it was sundays the last two have been Thursday mornings at 4:15ish) Looking at the logs (mysql, httpd, messages) there are no clues as to why. They just seem to stop. I ran a little script to take memory readings every 15 minutes and it too stops (with normal readings) at this time. The server is remote at a provider so I can only access it via the web. I use Plesk. It appears to be a set job or something that is causing the issue. I can see nothing in crontab. So my question is...has anyone else had this and can offer advice? Failing that. Does any one know of a way to get more detailed logging than that offered by the messages file? I was thinking of a black box style recording program or maybe something as simple as an option somewhere to increase the level of reporting in the messages log. Thanks

  Read the article

• Inactive users in windows server after some time according to first login instead of defining a solid expiration date

  - by smhnaji

  We want to give access to some Windows Server users so they can remotely have access to our server and download from a special folder of the server. The licenses we give to users, are time base. There should be 1 month, 2 month, ..., 1 year, ... licenses. CURRENT SITUATION (WHAT I DON'T WANT): When users are created and added to the OS, a solid expiration date is given. WHAT I WANT: Users' expiration date should be calculated automatically after first login. The user might not need his account right when purchases the license. In another words: When a license of the user we create is purchased at Jan 1st, he should use the license until Feb 1st. No matter whether he really logs in or not. He cannot come Feb 5th and begin using his license because that has expired then. What I want is that when he comes at Feb 5th and begins using, the license update until March 5th. CLARIFICATION (Update after MDMarra's comment) Working environment is Windows Server 2012. By the word 'user', I mean Native Windows Server Users. Whenever a new person purchases a license with me, I create them manually using net user command like this: net user ali pass /add /expires:2013-12-25

  Read the article

• Problems configuring logstash for email output

  - by user2099762

  I'm trying to configure logstash to send email alerts and log output in elasticsearch / kibana. I have the logs successfully syncing via rsyslog, but I get the following error when I run /opt/logstash-1.4.1/bin/logstash agent -f /opt/logstash-1.4.1/logstash.conf --configtest Error: Expected one of #, {, ,, ] at line 23, column 12 (byte 387) after filter { if [program] == "nginx-access" { grok { match = [ "message" , "%{IPORHOST:remote_addr} - %{USERNAME:remote_user} [%{HTTPDATE:time_local}] %{QS:request} %{INT:status} %{INT:body_bytes_sent} %{QS:http_referer} %{QS:http_user_agent}” ] } } } output { stdout { } elasticsearch { embedded = false host = " Here is my logstash config file input { syslog { type => syslog port => 5544 } } filter { if [program] == "nginx-access" { grok { match => [ "message" , "%{IPORHOST:remote_addr} - %{USERNAME:remote_user} \[% {HTTPDATE:time_local}\] %{QS:request} %{INT:status} %{INT:body_bytes_sent} %{QS:http_referer} %{QS:http_user_agent}” ] } } } output { stdout { } elasticsearch { embedded => false host => "localhost" cluster => "cluster01" } email { from => "[email protected]" match => [ "Error 504 Gateway Timeout", "status,504", "Error 404 Not Found", "status,404" ] subject => "%{matchName}" to => "[email protected]" via => "smtp" body => "Here is the event line that occured: %{@message}" htmlbody => "<h2>%{matchName}</h2><br/><br/><h3>Full Event</h3><br/><br/><div align='center'>%{@message}</div>" } } I've checked line 23 which is referenced in the error and it looks fine....I've tried taking out the filter, and everything works...without changing that line. Please help

  Read the article

• D-LINK DIR-615 router keeps giving my wireless devices bad ip addresses

  - by mlsteeves

  I have a D-LINK DIR-615 router, and wired devices have no problem getting an IP, however; wireless devices end up with a 169.254.. address (subsequently, they cannot access the internet through the router). I have removed all wired connections from the router, so there is no other dhcp server running. I've also gone back to the store, and replaced it with another, thinking that maybe it was defective. According to the router, it gave 192.168.0.101 to the wireless device. According to the wireless device it got 169.254.67.71. I've tried both a laptop and an iPod Touch, both exhibit the same behaviour. Has anyone seen this type of behaviour, or have any ideas of stuff to try? NEW INFORMATION I looked at the logs on the router, and when the wireless device tries to connect, this is what is logged: Sep 10 18:13:39 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:31 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:26 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:23 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:21 UDHCPD sending OFFER of 192.168.0.111 I connected a computer directly to the router, and here is what it looks like: Sep 10 18:14:18 UDHCPD Inform: add_lease 192.168.0.110 Sep 10 18:14:14 UDHCPD sending ACK to 192.168.0.110 Sep 10 18:14:14 UDHCPD sending OFFER of 192.168.0.110 Not sure if that helps or not.

  Read the article

• Preventing applications from performing run once tasks for multiple users

  - by JohnyV

  In our environment we have several applications that are installed that have a need to run a little prompt the first time they run eg Media player, Google earth etc. The problem is we have many users on many different computers. And the computers have deepfreeze running on them which removes the users profile once the computer is restarted. So next time that user logs in they have to go through the whole thing of run once again. I have managed to prevent IE runonce using group policy and office run once from using the office customisation tool. Is there a way to make this happen for other applications. On windows xp we used to copy a user that has run all the apps and place their default profile into the default profile so that new users get that profile template. Now with windows 7 the process of copy profiles is not as easy. Is there an easy way to copy profiles in win 7 or is there a better way (eg modify reg or app data) to prevent apps from performing an initial run. Thanks

  Read the article

• EFS Remote Encryption

  - by Apoulet

  We have been trying to setup EFS across our domain. Unfortunately Reading/Writing file over network share does not work, we get an "Access Denied" error. Another worrying fact is that I managed to get it working for 1 machine but no other would work. The machines are all Windows 2008R2, running as VM under ESXi host. According to: http://technet.microsoft.com/en-us/library/bb457116.aspx#EHAA We setup the involved machine to be trusted for delegation The user are not restricted and can be trusted for delegation. The users have logged-in on both side and can read/write encrypted files without issues locally. I enabled Kerberos logging in the registry and this is the relevant logs that I get on the machine that has the encrypted files. In order for all certificate that the user possess (Only Key Name changes): Event ID 5058: Audit Success, "Other System Events" Key file operation. Subject: Security ID: {MyDOMAIN}\{MyID} Account Name: {MyID} Account Domain: {MyDOMAIN} Logon ID: 0xbXXXXXXX Cryptographic Parameters: Provider Name: Microsoft Software Key Storage Provider Algorithm Name: Not Available. Key Name: {CE885431-9B4F-47C2-8415-2D766B999999} Key Type: User key. Key File Operation Information: File Path: C:\Users\{MyID}\AppData\Roaming\Microsoft\Crypto\RSA\S-1-5-21-4585646465656-260371901-2912106767-1207\66099999999991e891f187e791277da03d_dfe9ecd8-31c4-4b0f-9b57-6fd3cab90760 Operation: Read persisted key from file. Return Code: 0x0[/code] Event ID 5061: Audit Faillure, "System Intergrity" [code]Cryptographic operation. Subject: Security ID: {MyDOMAIN}\{MyID} Account Name: {MyID} Account Domain: {MyDOMAIN} Logon ID: 0xbXXXXXXX Cryptographic Parameters: Provider Name: Microsoft Software Key Storage Provider Algorithm Name: RSA Key Name: {CE885431-9B4F-47C2-8415-2D766B999999} Key Type: User key. Cryptographic Operation: Operation: Open Key. Return Code: 0x8009000b Could this be related to this error from the CryptAcquireContext function NTE_BAD_KEY_STATE 0x8009000BL The user password has changed since the private keys were encrypted. The problem is that the users I using at the moment can not change their password.

  Read the article

• Power issues Foxconn Barebones kit

  - by alpha1

  I have a Foxconn R20D2 bought about a year and a half ago. It ran fine for a while and then around last summer it started having power issues. I chalked it up to changes in electric current due to the overwhelmed grid when people turn on their AC units, but this problem has stayed for all year, shutting off randomly, shutting off when i turn on a vacuum and similar problems. Now that its summer again, the box basically sits there all day cycling itself, and now has gotten to the point it tried to boot and after 3 seconds, fails, shuts off and tried again. I know its power related, it runs opensuse linux and there are never any shutdown logs or anything of that sort. As the weather got hotter i noticed it happening more and more, and it most often happened in the morning, i presume as people woke up and turn on the AC. The power supply is a Chennel well technology co LTD model DSL-150. 150W max output. Its an intel atom dual core, with 2 sata drives, no CD/floppy etc, recently upgrades from 2 to 4gb of ram. It runs at 104 degrees Fahrenheit all the time almost. Any way i can test the power supply or anything else to try to fix it? Im a software guy, not hardware so im at a complete loss here, thanks for all assistance you can provide! EDIT: The switch on the back that says 230 or 115 is set to 230. If im in the USA, could that be causing the problems?

  Read the article

• How to set up mysql storage for certain rsyslog input matches?

  - by ylluminate

  I'm draining various logs from Heroku to an rsyslog linux (ubuntu) server and am starting to have a little more to bite off than I can chew in terms of working with my log histories. I am needing to be able drill back in time based on more flexible details and more flexible access than what the standard syslog file(s) provide. I'm thinking that logging to mysql may be the correct approach, but how do I set this up such that it pulls only certain log entries into a table based on an identified? For example, I see a long hex string identifying each log entry from a certain Heroku app instance. I assume that I can just pipe those into the mysql socket vs ALL rsyslog input into mysql... Could someone please direct me to a resource that can walk me through the process of setting something like this up or simply provide some details that can help? I have 15+ years of Unix experience so I just need some nudging in the right direction as I've not really done a tremendous amount of work with syslog daemons previously in terms of pooling various servers into one. Additionally, I'd be interested in any log review tools that could make drilling through log arrangements like this more handy for developers.

  Read the article

• Very slow connection to xserve via afp or smb

  - by Mhoffman13

  Help. File transfer and connection speed to our Xserve are painfully slow from newly purchased iMacs. The Xserve is only used as a file server, its running 10.4.11. The problem seems to be only happening on brand new iMacs running 10.6.3. When connected either over afp or smb copying files is many times slower than usual. Other machines on the network running either 10.4 or 10.5 have a normal connection speed. To try to rule out OS incompatibility I connected the new iMac running 10.6 to another computer running 10.4 over the network. The file transfer speed was fast as normal. So it seems the problems lies with the X serve (maybe). The afp logs either access or error don't show anything unusual. One thing that did look different was when the imac was connected to the Xserve the user had its id listed as its IP address. The other machines connected, had the id of broadcasthost. I also noticed that when connected from the new iMac I can only see one of the mirrors. When any other computer connects both mirrors are shown. Tried a restart of the Xserve but the problem persists. Thanks in advance for any advice

  Read the article

• SSH Interactive mode not working

  - by Ekin Koc

  I have a Debian based linux server running for a year or so, without any problems. A couple of days ago, ssh interactive mode stopped working for no reason. I mean, I can open an ssh connection just fine, the server greets me with shell but I just can't type anything. However, if I send commands like this: ssh [email protected] cat /var/log/messages, I get the response. I dug through several logs and found one message, which feels remotely relevant to the problem; sh kernel: [10222733.062511] ------------[ cut here ]------------ sh kernel: [10222733.062522] WARNING: at /build/buildd-linux-2.6_2.6.32-39-amd64-7yVIH2/linux-2.6-2.6.32/debian/build/source_amd64_none/drivers/char/tty_ldisc.c:738 tty_ldisc_reinit+0x46/0x7b() sh kernel: [10222733.062526] Hardware name: PowerEdge R210 II sh kernel: [10222733.062528] Modules linked in: ipt_MASQUERADE iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack nf_defrag_ipv4 ip_tables x_tables sha1_generic arc4 ecb ppp_mppe ppp_async crc_ccitt ppp_generic slhc loop snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 i2c_core pcspkr evdev joydev dcdbas container button processor ext3 jbd mbcache sg sd_mod sr_mod crc_t10dif cdrom usb_storage usbhid hid mpt2sas ahci ehci_hcd libata scsi_transport_sas usbcore bnx2 nls_base scsi_mod fan thermal thermal_sys [last unloaded: scsi_wait_scan] sh kernel: [10222733.062568] Pid: 8662, comm: sshd Not tainted 2.6.32-5-amd64 #1 sh kernel: [10222733.062569] Call Trace: sh kernel: [10222733.062572] [<ffffffff811ff056>] ? tty_ldisc_reinit+0x46/0x7b sh kernel: [10222733.062574] [<ffffffff811ff056>] ? tty_ldisc_reinit+0x46/0x7b Is there any way to get back the sshd working in interactive mode? I tried restarting sshd but that is no help. And somehow, I can not reboot the server. Tried sending shutdown -r now and reboot but it refuses to go down. Should I go ahead and request a physical reboot?

  Read the article

< Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >