Search Results

Search found 13909 results on 557 pages for 'old man'.

Page 157/557 | < Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >

• OpenIndiana (illumos): vmxnet3 interface lost on reboot

  - by protomouse

  I want my VMware vmxnet3 interface to be brought up with DHCP on boot. I can manually configure the NIC with: # ifconfig vmxnet3s0 plumb # ipadm create-addr -T dhcp vmxnet3s0/v4dhcp But after creating /etc/dhcp.vmxnet3s0 and rebooting, the interface is down and the logs show: Aug 13 09:34:15 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:15 neumann vmxnet3s: [ID 715698 kern.notice] vmxnet3s:0: stop() Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:17 neumann vmxnet3s: [ID 920500 kern.notice] vmxnet3s:0: start() Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(TxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxBufPoolLimit) -> 512 Aug 13 09:34:17 neumann nwamd[491]: [ID 605049 daemon.error] 1: nwamd_set_unset_link_properties: dladm_set_linkprop failed: operation not supported Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x20000) -> no Aug 13 09:34:17 neumann nwamd[491]: [ID 751932 daemon.error] 1: nwamd_down_interface: ipadm_delete_addr failed on vmxnet3s0: Object not found Aug 13 09:34:17 neumann nwamd[491]: [ID 819019 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv4 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 160156 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv6 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 771489 daemon.error] 1: add_ip_address: ipadm_create_addr failed on vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 405346 daemon.error] 9: start_dhcp: ipadm_create_addr failed for vmxnet3s0: Operation not supported on disabled object I then tried disabling network/physical:nwam in favour of network/physical:default. This works, the interface is brought up but physical:default fails and my network services (e.g. NFS) refuse to start. # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 vmxnet3s0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:1: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:2: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:3: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:4: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:5: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:6: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:7: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:8: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 vmxnet3s0: flags=20002000840<RUNNING,MULTICAST,IPv6> mtu 9000 index 2 inet6 ::/0 # cat /var/svc/log/network-physical\:default.log [ Aug 16 09:46:39 Enabled. ] [ Aug 16 09:46:41 Executing start method ("/lib/svc/method/net-physical"). ] [ Aug 16 09:46:41 Timeout override by svc.startd. Using infinite timeout. ] starting DHCP on primary interface vmxnet3s0 ifconfig: vmxnet3s0: DHCP is already running [ Aug 16 09:46:43 Method "start" exited with status 96. ] NFS server not running: # svcs -xv network/nfs/server svc:/network/nfs/server:default (NFS server) State: offline since August 16, 2012 09:46:40 AM UTC Reason: Service svc:/network/physical:default is not running because a method failed. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:default Reason: Service svc:/network/physical:nwam is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:nwam Reason: Service svc:/network/nfs/nlockmgr:default is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/network/nfs/nlockmgr:default See: man -M /usr/share/man -s 1M nfsd Impact: This service is not running. I'm new to the world of Solaris, so any help solving would be much appreciated. Thanks!

  Read the article

• Driver Scanner detect driver needed

  - by Pennf0lio

  Hi, I'm currently fixing the laptop of my friend. Her Laptop is kinda old and is not a well know brand (Redfox Navigator), So that means there are lack of support online. Are there Software that you install and will scan the system and will look for the driver that it needs? Note: The Laptop can't connect through the internet. thanks!

  Read the article

• Multiple VLANs, multiple subnets, single DHCP server?

  - by EightQuarterBit

  Hey guys! At my job we are prepping to transition from multiple LANs connected over slow VPN connections to a single MAN connected over fiber, and I've got a few questions. First of all, we are planning on making each physical site its own VLAN, but we would like to have a single DHCP server at the data center hand out IPs to each VLAN. We've pretty much got the VLAN tagging structure all worked out, but we would like to have our single DHCP server assign different subnets of IPs to each VLAN. For instance, VLAN 2 gets 10.0.2.x through 10.0.4.x, VLAN 3 gets 10.0.5.x through 10.0.7.x etc. We are an Active Directory based shop and we have a Server 2003 box handling DHCP (though we aren't averse to upgrading it to server 2008.) Is this feasible, or am I pipe-dreaming?

  Read the article

• Learning Linux screencasts

  - by Dmitriy Nagirnyak

  Hi, I am trying to get started with Linux. There are number of books (many of which are just man pages), some of them provide good overview so I can dig deeper online then. What I would like is to find number of screencasts that would cover basics of Linux commands, server administration, commonly performed tasks etc (no GUI, only terminal). I want to watch the screencasts to "get it quicker" and then use a book or online resources to "dig it deeper". Any recommendations? Thanks, Dmitriy.

  Read the article

• How to reboot a WindowsCE5 device?

  - by Stijn Sanders

  Is there a way to force a device running Windows CE 5.0 to reboot? I remember Ctrl+Alt+Del from the old days on PC's, but I don't know if there's a keyboard-combination I could use on this Datalogic BlackJet, and I can't seem to find a reset pin-hole. I tried taking the battery out, and waiting a few hours, but that totally reset the device from ROM, undoing all setup I'd done.

  Read the article

• VSFTPD and Implicit SSL

  - by Luma

  Hi Everyone, I have a Debian Dedicated server and I want to enable Implicit SSL on it using VSFTPD and I am having a hard time. I have read online and the only thing I can really find is how to enable SSL and in the man pages it lists one implicit ssl command. but since Implicit ssl uses a second listener (990 by default) I have no idea how to make it work on Debian. Has anyone managed to get this working? Here is my config: listen=YES anonymous_enable=NO local_enable=YES write_enable=YES local_umask=022 connect_from_port_20=YES pam_service_name=vsftpd ssl_enable=YES allow_anon_ssl=NO force_local_data_ssl=NO force_local_logins_ssl=NO ssl_tlsv1=YES ssl_sslv2=NO ssl_sslv3=NO rsa_cert_file=/etc/ssl/certs/vsftpd.pem if I include Implicit_SSL=YES the server won't even start. thanks

  Read the article

• Juniper SSG5 find bandwidth eater

  - by Pol

  Hello forum, I looking for a way to get the list of the top bandwidth eater on my Juniper ssg5. On my old OpenBSD Box I had a command line version of ntop. It was just perfect. How can I do the same thing whith the SSG? Thank you !

  Read the article

• How do I view the job queue in lftp after it has moved to a background process?

  - by drpfenderson

  I've just started using lftp for remote transferring files on my Raspberry Pi running Debian. I know how to transfer the files, and use queue and jobs to add and view transferring files. However, I'm not actually sure on how to view these transfers once lftp moves to the background. The lftp man page mentions how lftp is moving to the background, but when I open a new instance of the program from shell and type jobs, the queue is empty. However, I can clearly see using my file manager that the transfers are still happening, as the files are there and growing in size. I'm guessing that when I reopen lftp, it's just opening a new instance that isn't connected to the nohup mode lftp that has the active queue. I've tried searching various places, but no one else seems to have this particular issue. So, I guess what I'm asking is twofold: Is there a way to easily attach to the background lftp process to view the current jobs list? If not, is there a way to view this at all?

  Read the article

• RAM modules compadibility

  - by teejmya

  My current laptop has 3GB (1x2GB, 1x1GB) of DDR2 RAM installed, and they run at 667MHz. I just ordered a new laptop, that comes with 2GB (2x1GB) of DDR3 RAM that runs at 1066MHz. Is there any compatibility with the two? Can I install the 2GB stick in my old laptop in the new laptop, and have both DDR2/DDR3 and 667MHz/1066MHz operating together? Or should I buy a new RAM stick for my new laptop?

  Read the article

• Remap paths used in Windows Movie Maker projects

  - by Fuxi

  I need to rebuild path structures for old Windows Movie Maker projects under a new Windows 7 install. The problem is that those projects refer to files of a certain file path that can't be rebuiltd in Windows 7 ("Documents and Settings" is blocked). Is there a way to batch convert those projects with updated paths? Some file specs of the WMM file format (for coding a little utility) would be helpful as well.

  Read the article

• Probelm After Changing password in ubuntu

  - by Narendra

  Hi All, I am using ubuntu system which uses openldap for user login authentication. For changing my login password i used "$sudo passwd" and changed it. (of course the password given is same as old one). Then onwards when i trying to run "apt" command it showing command not found. and for some other programs it showing segmentation fault. Can any one tell me why I am facing issue and how to solve this.

  Read the article

• bypass PAE, NX, and SSE2 upgrade requirements from windows 8 to windows 8.1

  - by Jonathan

  On one of my old computers I am having the problem of upgrading to windows 8.1 because my computer does not support PAE, NX, and SSE2. How was I able to install windows 8 in the first place? I heard the original requirements for windows 8.0 were PAE, NX, and SSE2. Anyone know a bypass for this on a machine already running windows 8? IMO 8.1 should have been released in the form of a service pack not an entirely new windows.

  Read the article

• How do you enable syslogd to accept incoming connections on Snow Leopard from remote loggers?

  - by Emmel

  How do I get syslogd to accept incoming connections from remote hosts on Snow Leopard? I'd like to centralize logging such that various devices and systems send logs to Snow Leopard's syslogd, which normally hangs out on UDP 514. However, I'm unable to get them to successfully be accepted by good ole syslogd. I tcpdumped on the Snow Leopard box to verify that packets are being spouted to port 514 -- they are. I checked that syslogd is listening on 514 -- it's not. Googling around told me that, on older versions of OSX (don't you love the way things change so rapidly on OSX), one just had to add a flag to the syslogd daemon to allow remote; one did this in com.apple.syslogd.plist. However the syslogd daemon has no flags (at least in its man page) that suggests any remote anything. What's the solution to this? Secondary, less import but relevant question: What's 'newsyslog'? I see a plist file but it's not running (apparently). Thanks

  Read the article

• Hardware requirements for playing HD

  - by asdasd

  A friend of mine has some HD videos (720p and 1080p), so i would like what are the hardware requirements in order to play them correctly with no slowing-downs ? my computer is build of : Intel(R) Celeron(R) CPU 2.40GHz nvidia GeForce 5200 FX 768 RAM My friend said that it won't be possible to play the HD videos on my comp because of it's old hardware - is this true ? And again, what are the minimal hardware setup needed to play HD ? Thanks.

  Read the article

• File sync over LAN

  - by Jack

  At the moment, I'm using Dropbox on my computer and Dropsync on my Android phone (over WiFi) to one-way sync the files (such as photos/app backups) on my phone to the Dropbox servers which are then synced to my computer. I like the features of Dropsync which can be set to sync only when the phone is charging and the WiFi is on. So everytime I charge my phone, i know my files are being backed up. Now I'm wondering if there's a similar app/program combo or something that can do what I'm currently doing but remove the middle-man (Dropbox servers)?

  Read the article

• Redirect absolutely anything to new domain with .htaccess

  - by John Hunt

  Ok, so I'm in need a simple redirect: Redirect 301 / http://www.new.com/ Similar to that, except I want it to catch anything, such as: www.old.com/blah/blah/?xyz=123&aaaaabbbb=erewr3ttt#ewtjhirhjerh and send the user to: www.new.com Should be easy right? Finding out how to do this is not so easy. Using the above rule we're still getting 404's for things that aren't there rather than the Redirect rule just getting everything.

  Read the article

• Tuning Linux IP routing parameters -- secret_interval and tcp_mem

  - by Jeff Atwood

  We had a little failover problem with one of our HAProxy VMs today. When we dug into it, we found this: Jan 26 07:41:45 haproxy2 kernel: [226818.070059] __ratelimit: 10 callbacks suppressed Jan 26 07:41:45 haproxy2 kernel: [226818.070064] Out of socket memory Jan 26 07:41:47 haproxy2 kernel: [226819.560048] Out of socket memory Jan 26 07:41:49 haproxy2 kernel: [226822.030044] Out of socket memory Which, per this link, apparently has to do with low default settings for net.ipv4.tcp_mem. So we increased them by 4x from their defaults (this is Ubuntu Server, not sure if the Linux flavor matters): current values are: 45984 61312 91968 new values are: 183936 245248 367872 After that, we started seeing a bizarre error message: Jan 26 08:18:49 haproxy1 kernel: [ 2291.579726] Route hash chain too long! Jan 26 08:18:49 haproxy1 kernel: [ 2291.579732] Adjust your secret_interval! Shh.. it's a secret!! This apparently has to do with /proc/sys/net/ipv4/route/secret_interval which defaults to 600 and controls periodic flushing of the route cache The secret_interval instructs the kernel how often to blow away ALL route hash entries regardless of how new/old they are. In our environment this is generally bad. The CPU will be busy rebuilding thousands of entries per second every time the cache is cleared. However we set this to run once a day to keep memory leaks at bay (though we've never had one). While we are happy to reduce this, it seems odd to recommend dropping the entire route cache at regular intervals, rather than simply pushing old values out of the route cache faster. After some investigation, we found /proc/sys/net/ipv4/route/gc_elasticity which seems to be a better option for keeping the route table size in check: gc_elasticity can best be described as the average bucket depth the kernel will accept before it starts expiring route hash entries. This will help maintain the upper limit of active routes. We adjusted elasticity from 8 to 4, in the hopes of the route cache pruning itself more aggressively. The secret_interval does not feel correct to us. But there are a bunch of settings and it's unclear which are really the right way to go here. /proc/sys/net/ipv4/route/gc_elasticity (8) /proc/sys/net/ipv4/route/gc_interval (60) /proc/sys/net/ipv4/route/gc_min_interval (0) /proc/sys/net/ipv4/route/gc_timeout (300) /proc/sys/net/ipv4/route/secret_interval (600) /proc/sys/net/ipv4/route/gc_thresh (?) rhash_entries (kernel parameter, default unknown?) We don't want to make the Linux routing worse, so we're kind of afraid to mess with some of these settings. Can anyone advise which routing parameters are best to tune, for a high traffic HAProxy instance?

  Read the article

• Torque and maui node status

  - by Lafada

  I am new for torque and maui. I was checking for node state to looking for which nodes are free and which nodes are in use. For torque one command is pbsnodes. Which gives status and other info related to node. When I was checking for maui then I found command diagnose -n which also shows status of the node. I was wondering between these 2 status. Both are giving different status for the same situation. When I do man pbsnodes I got the possible states for node "free", "offline", "down", "reserve", "job-exclusive", "job-sharing", "busy", "time-shared", or "state-unknown" But this type of different state I cant find for diagnose -n. How pbsnodes and diagnose -n get the status for node. Is there any database like xCAT use for torque or maui? Thx in advance for your valuable time.

  Read the article

• Do i need to join Graphics Card with CPU fan

  - by Mirage

  Initially i had inno 3d 256MB Nvidia GTS graphics card. I also had another Big FAN above the processor (Vendor put in quad core) In that card there was one cable which was joined with that FAN. Now i have changed the CARD to 1GB Nvidia GT9600 . But there is no pins to join the fan with that card. Is it ok . i don't know why old card was joined with FAN

  Read the article

• Command line tool for MediaWiki?

  - by Magnus

  Is there a command line tool that would allow me to script creation of accounts on a MediaWiki instance? The UI for creating an account is painful, and very time consuming when tasked with creating 10+ accounts at a time. Unfortunately I can't get ImportUsers to work due to the very old version of MediaWiki we use (and upgrading is unfortunately not possible at this time).

  Read the article

• Is Splitting IDE hdds between Primary and Secondary faster?

  - by earlz

  Hello, I'm doing RAID 0 on two IDE harddrives (yes, this is old hardware). Will the harddrives be faster if I attach them separately so that one is on the Primary IDE controller and the other is on the Secondary IDE controller? Or would it just be as good as having them both on the Primary IDE as master and slave?

  Read the article

• Can I use my existing SSL certificates on a new server with Plesk?

  - by Wil

  We are migrating to a Virtual Private Server running on Ubuntu 8.04 LTS and with a Plesk configuration panel. We have some valid SSL certificates on the old server, which I would like to use on the new configuration. I have the CSR, private key, certificate and CA-certificate. I cannot find a way to change the CSR and private key in the Plesk configuration panel. Anyone know, if this is possible and how?

  Read the article

• Keep IIS7 Failed Request Tracing as a sysadmin only diagnostic tool?

  - by Kev

  I'm giving some of our customers the ability to manage their sites via IIS Feature Delegation and IIS Manager for Remote Administration. One feature I'm unsure about permitting access to is Failed Request Tracing for the following reasons: Customers will forget to turn it off The server will be taking a performance hit (especially if 500 sites all have it turned on) The server will become littered with old FRT's The potential to leak sensitive information about how the server is configured thus providing useful information to would-be intruders. Should we just keep this as a troubleshooting tool for our own admins?

  Read the article

• Is there a way to completely flush cached AD credentials on a user workstation?

  - by Mikey B

  An AD user updated their AD password, but a couple applications on their workstation appear to still be using their old AD credentials. Is there an easy way to flush out cached AD credentials on Windows (short of logging out or rebooting)? A few google searches hinted at "gpupdate /force" but I wasn't sure if that would encompass stuff like NTLM credentials and AD passwords.

  Read the article

• Is there a way to completely flush cached AD credentials on a user workstation?

  - by Mikey.B

  An AD user updated their AD password, but a couple applications on their workstation appear to still be using their old AD credentials. Is there an easy way to flush out cached AD credentials on Windows (short of logging out or rebooting)? A few google searches hinted at "gpupdate /force" but I wasn't sure if that would encompass stuff like NTLM credentials and AD passwords. Thanks, M

  Read the article

< Previous Page | 153 154 155 156 157 158 159 160 161 162 163 164  | Next Page >