Search Results

Search found 15898 results on 636 pages for 'auto properties'.

Page 159/636 | < Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >

• Can only bring up one of two interfaces

  - by mstaessen

  I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

  Read the article

• Active Directoy LDAP - Lock User Account

  - by Germ

  What is the prefered way to lock an Active Directory account? int val = (int)directoryentry.Properties["userAccountControl"].Value; directoryentry.Properties["userAccountControl"].Value = val | 0x0010; vs. directoryentry.InvokeSet("IsAccountLocked", true); Is there a better way?

  Read the article

• Network monitoring library, or objects, for a cloud

  - by Andrew Smith

  I am looking for library to support server / switch monitoring, to actually be able to check with the device if it's working OK. However this requires some sort of auto-detection and device support. Basically I need to automatically detect a new device, start monitoring it like CPU and PING. So how do I auto-detect the machine remotely, this is something I need library for. Rackspace has something like this - "Cloud Monitoring API". But is there anything opensource which can be used same way? The Nagios and others doesnt have such API, and the big and expensive systems are too big to handle in public cloud, so there must be some other network monitoring engine with API, which can add a new servers automatically and support user isolation for example so I dont see other servers except mine.

  Read the article

• Attached property and style missing on re adding the user control

  - by RodD

  Hey people I've got an issue with a WPF project I'm working on, I have an items control which I add to and remove from certain user controls, these contols styles and attached properties are there on first view but when I remove and add them again the user control apears on screen but is detached from the items control attached properties and styles. Is this behaviour common and if so what is the best way to handle it? Thanks in advance

  Read the article

• Messages Disappeared from Outlook Sent Folder

  - by Bryan

  Two days ago almost all of the messages in my Microsoft Outlook sent folder disappeared. I say "almost all" because only the messages from the past 2 weeks remain. This led me to believe that they must have been "auto archived," but I can't find an archive file that contains my messages. I've checked the folder where Outlook says it archives messages, but there's not much there. I've changed my settings to prevent Outlook from auto-archiving my messages in the future, but still need the ones that have disappeared. Can anybody help me find my missing messages?

  Read the article

• How can one automatically logon to multiple user accounts in Windows 2008 R2

  - by DJFriar

  We are running a Windows 2008 R2 Terminal Server. Currently, we have local admin accounts created, one for each client that runs our software (SiteA, SiteB, etc). We need these user accounts to auto logon if the server is rebooted. The accounts need to run a full user environment, as we will login remotely at times via TeamViewer to check processes and makes changes, etc. We are using the Registry Hack method now, but that only allows one account to logon. I've seen a program called LogonExpert, but I've never heard of it so I don't know how trust worthy it is, etc. Is there any other way to auto logon to multiple accounts in our environment? Currently the users are local users, but we could make them domain users if that is required.

  Read the article

• How can I get a string[] of all different values of a list?

  - by iTayb

  I have a class that has an list<Book> in it, and those Book objects has many many properties. string Subject is one of those properties. I'd like to get an string[] type value that will include all different subjects from all over the list. Is there an elegant way to do it, or I'll have to scan the whole list and enter each subject to it, then remove duplicates?

  Read the article

• Listen to any change in the values of an Object in Actionscript

  - by Ali

  Hi All, I have an Object in actionscript which has a few dozens of properties each of which is defined to be bindable and has its own change event. I would like to listen to any changes made to this object without having to add a listener to all of its properties. Is there a way in actionscript using which I can listen to any change in the values of an Object ? Thanks, -A

  Read the article

• Windows 7: Screen will power off, or blank and lock, but not both.

  - by Heptite

  For some reason, my Windows 7 (Ultimate, 64bit) laptop will not power off the display and keep it off if I have the screen saver and/or the timed auto-lock enabled. Either the display blanks (and locks) but never powers off, or it powers off for less then a minute, then the back light visibly powers back on and stays on, even though the screen remains blanked until I touch a key or the trackpad. I've tried varying the screen power down time to greater than, less than, and exactly equal to the blank screen/lock time, with no success. Turning the screen saver and the timed auto-lock off does allow the timed display power down in the power settings to work properly. (Note that I am not talking about system sleep or hibernate. I'm talking about when the machine remains running, but only the display should power down.)

  Read the article

• How do I disable automatic updates on OpenSUSE 12.2

  - by MathematicalOrchid

  For reasons unknown, OpenSUSE seems to have half a dozen different places that mention auto-update. Is there a way I can definitely, permanently, irreversibly disable auto-update so that new software will never, ever, under any circumstances, be installed? Ideally I want to prevent the OS from even connecting to the Internet to see if any updates are available. I've unchecked half a dozen things, but I'm still getting alerts telling me updates are available. I do now want updates! I can't believe this is so hard to turn off... In case it makes any difference, OpenSUSE 12.2 with a GNOME desktop.

  Read the article

• What process is resurrecting mysqld?

  - by ripper234

  I'm following this guide to reset my mysql root password (I'm on ubuntu). When I kill the mysqld process, it immediately gets resurrected. The parent process ID is 1. How can I find what keeps resurrecting mysqld? $ ps -ef | grep mysql mysql 30136 1 0 07:16 ? 00:00:00 /usr/sbin/mysqld root 30295 30274 0 07:18 pts/0 00:00:00 grep --color=auto mysql $ kill -9 30136 $ ps -ef | grep mysql mysql 30302 1 2 07:18 ? 00:00:00 /usr/sbin/mysqld root 30404 30274 0 07:18 pts/0 00:00:00 grep --color=auto mysql $

  Read the article

• Excel 2010 started changing my numbers

  - by Going Crazy

  If I type in a 16 digit number (format: number, no decimals) it changes the number on me. Example: 1234567812345678 changes the view to 1234567812345670. If I type it in as a general format it changes the numbers above so it displays 1.23457E+15 but if you click on the cell, the display shows the last digit as a 0 instead of an 8 once again. I opened the file on a different computer and same issue now with it. I have changed the auto correcting and auto formating all to no avail. Help!

  Read the article

• NSD reply from unexpected source

  - by Ximik

  I have server with NSD. There are MAIN_IP and ADD_IP. When I try to get IP of my site from server I have right output dig @localhost my_site.com But when I try to make this from my PC, I have dig @my_ns_server.com my_site.com ;; reply from unexpected source: MAIN_IP#53, expected ADD_IP#53 (ADD_IP is IP of my_ns_server.com) What should I do? UPD: My interfaces conf auto eth2 allow-hotplug eth2 iface eth2 inet static address xxx.xxx.xxx.234 netmask 255.255.255.252 network xxx.xxx.xxx.232 broadcast xxx.xxx.xxx.235 gateway xxx.xxx.xxx.233 dns-nameservers MY_ISP_IP dns-search MY_ISP_DOMAIN auto eth2:0 iface eth2:0 inet static address xxx.xxx.xxx.124 netmask 255.255.255.0 xxx.xxx.xxx is the same for all IPs

  Read the article

• how to insert into database from stored procedure in log4net?

  - by Samreen

  I have to log thread context properties like this: string logFilePath = AppDomain.CurrentDomain.BaseDirectory + "log4netconfig.xml"; FileInfo finfo = new FileInfo(logFilePath); log4net.Config.XmlConfigurator.ConfigureAndWatch(finfo); ILog logger = LogManager.GetLogger("Exception.Logging"); log4net.ThreadContext.Properties["MESSAGE"] = exception.Message; log4net.ThreadContext.Properties["MODULE"] = "module1"; log4net.ThreadContext.Properties["COMPONENT"] = "component1"; logger.Debug("test"); and the configuration file is: <configuration> <configSections> <section name="log4net" type="log4net.Config.Log4NetConfigurationSectionHandler,Log4net"/> </configSections> <log4net> <logger name="Exception.Logging" level="Debug"> <appender-ref ref="AdoNetAppender"/> </logger> <appender name="AdoNetAppender" type="log4net.Appender.AdoNetAppender"> <connectionString value="Data Source=xe;User ID=test;Password=test;" /> <connectionType value="System.Data.OracleClient.OracleConnection, System.Data.OracleClient, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089" /> <bufferSize value="10000"/> <commandText value="Log_Exception_Pkg.Insert_Log" /> <commandType value="StoredProcedure" /> <parameter> <parameterName value="@p_Error_Message" /> <dbType value="String" /> <size value="255" /> <layout type="log4net.Layout.PatternLayout"> <conversionPattern value="%property{MESSAGE}"/> </layout> </parameter> <parameter> <parameterName value="@p_Module" /> <dbType value="String" /> <size value="225" /> <layout type="log4net.Layout.PatternLayout"> <conversionPattern value="%property{MODULE}"/> </layout> </parameter> <parameter> <parameterName value="@p_Component" /> <dbType value="String" /> <size value="225" /> <layout type="log4net.Layout.PatternLayout"> <conversionPattern value="%property{COMPONENT}"/> </layout> </parameter> </appender> </log4net> </configuration> But its not inserting them in the database. How can I get that to work?

  Read the article

• Complex query with two tables and multilpe data and price ranges

  - by TiuTalk

  Let's suppose that I have these tables: [ properties ] id (INT, PK) name (VARCHAR) [ properties_prices ] id (INT, PK) property_id (INT, FK) date_begin (DATE) date_end (DATE) price_per_day (DECIMAL) price_per_week (DECIMAL) price_per_month (DECIMAL) And my visitor runs a search like: List the first 10 (pagination) properties where the price per day (price_per_day field) is between 10 and 100 on the period for 1st may until 31 december I know thats a huge query, and I need to paginate the results, so I must do all the calculation and login in only one query... that's why i'm here! :)

  Read the article

• how to save class object in registry, C sharp.

  - by younevertell

  Basically I have one class object with some properties. Is there any way I can save the class object in registry, not the properties seperately? It seems RegistryKey.SetValue Method can not save an object directly?

  Read the article

• Animating elements of text-shadow with jQuery

  - by bryceroney

  I was wondering if there was any way to, using jQuery, animate properties of text-shadow like size or colour. It's annoying that there aren't individual properties like text-shadow-color instead of the statement only being available in combined form.

  Read the article

• Cannot save property group to product in django-lfs

  - by vernomcrp

  I already create properties and add them to property group.Then I assign to my new product.But django show me TypeError at /manage/update-product-properties/1 save() got an unexpected keyword argument 'using'

  Read the article

• MySQL simple replication problem: 'show master status' produces 'Empty set'?

  - by simon

  I've been setting up MySQL master replication (on Debian 6.0.1) following these instructions faithfully: http://www.neocodesoftware.com/replication/ I've got as far as: mysql > show master status; but this is unfortunately producing the following, rather than any useful output: Empty set (0.00 sec) The error log at /var/log/mysql.err is just an empty file, so that's not giving me any clues. Any ideas? This is what I have put in /etc/mysql/my.cnf on one server (amended appropriately for the other server): server-id = 1 replicate-same-server-id = 0 auto-increment-increment = 2 auto-increment-offset = 1 master-host = 10.0.0.3 master-user = <myusername> master-password = <mypass> master-connect-retry = 60 replicate-do-db = fruit log-bin = /var/log/mysql-replication.log binlog-do-db = fruit And I have set up users and can connect from MySQL on Server A to the database on Server B using the username/password/ipaddress above.

  Read the article

• What is the method of creating a skin menu?

  - by cosgeo99

  I want to develop a custom skin or a css for ASP default menu. I want my menu look like the custom controls that are available for purchase like Rad from Telerik. If have tried to google for CSS properties of the ASP Menu but have found only some expose properties. Would really appreciate some help here.

  Read the article

• child objects in rdlc (Studio 2010RC)

  - by Jim

  Hi, I am attempting to reference a sub-object in a field expression in a studio 2010 report. This used to work in prior versions. When account references another object with properties the following used to work. =Fields!Account.Value.Name (Name is a property of the child object, Account is the parent object) The same expression syntax no longer works. How do I reference the properties of a sub-object in reporting services in an rdlc in studio 2010. Thanks

  Read the article

• Unable to change IP address for eth0 without restart in Ubuntu

  - by Rodnower

  I have Ubuntu 12.04.1 installed. I tried to change the IP address of the interface eth0 in /etc/network/interfaces from 192.168.1.3 to 192.168.1.4 auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.up.rules auto eth0 iface eth0 inet static address 192.168.1.4 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 sudo service networking status When I issue: sudo service networking restart I get this response: stop: Unknown instance: networking stop/waiting And IP remains 192.168.1.3: eth0 Link encap:Ethernet HWaddr 00:1e:33:71:cd:a4 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe71:cda4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3861 errors:0 dropped:0 overruns:0 frame:0 TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3423285 (3.4 MB) TX bytes:521854 (521.8 KB) Interrupt:45 Base address:0x4000 Only after restart does the IP change. Any ideas?

  Read the article

• How to map LINQ EntitySet to List property in property setter?

  - by jlp

  In my model I have these entities: public interface IOrder { string Name {get;set;} List<IProduct> OrderedProducts {get;set;} } public interface IProduct {} In partial class generated by linq-to-sql I map these properties on my entity properties: public partial class Order : IOrder { List<IProduct> OrderedProducts { get { return this.L2SQLProducts.Cast<IProduct>.ToList(); } set { this.L2SQLProducts = ??? } } } How should setter look like?

  Read the article

• Connecte RemoteApp to Exising Session

  - by Fowl

  Due to the slightly retardedness of an app I've got to run, I've got a server auto logging in on boot with the app on auto start. Remote desktop at my leisure to check on its status, etc. Gross, but it works. Now I've tried out RemoteApp which seems to work ok (ie. remotes the notification icon, balloons...) except for the fact that it creates a new session (and therefore instance of my app) - this confuses the heck out of app and it means that if I was using 'full' remote desktop I lose all my state. "Restrict each user to a single session" doesn't work. IIRC "Windows XP Mode" uses RemoteApp and it doesn't seem to have any trouble switching between modes. So how can I connect to a running app?

  Read the article

• How do I expand my <div> to properly fit more vertical content?

  - by CSS_maniac

  Whenever I try to add margin-top: 30px to my box_1 and box_2 <div>, my bottom <div> gets pushed down and disappears. It seems like my wrapper wont expand to fit the content. How do I get a 30px gap between top and box_1/2 and bottom? <html> <head> <title>Circle Motion</title> <link rel="stylesheet" type="text/css" href="styles.css" /> </head> <body> <div id="outer-wrapper"> <div id="wrapper"> <div id="top"> </div> <div id="box_1"> <img src="chrome_400x400.png" /> </div> <div id="box_2"> <img src="firefox_400x400.png" /> </div> <div id="bottom"> <p>All Rights Reserved - CSS_maniac 2012 ©</p> </div> </div> </div> </body> </html> CSS /* My CSS */ html { height: 100% } body { background-color: grey; } #outer-wrapper { height: 100%; width: 1000px; margin: 0px auto; background-color: #EAFFDB; -moz-border-radius: 15px; border-radius: 15px; } #wrapper { height: 100%; width: 960px; margin: 0px auto; background-color: #EAFFDB; overflow: hidden; } #top { width: 900px; height: 110px; margin-top: 35px; margin-left: 30px; margin-right: 30px; background-color: white; -moz-border-radius: 15px; border-radius: 15px; } #box_1 { width: 430px; height: 430px; background-color: white; -moz-border-radius: 15px; border-radius: 15px; float:left; margin-left: 30px; text-align: center; } #box_2 { width: 430px; height: 430px; background-color: white; -moz-border-radius: 15px; border-radius: 15px; float:right; margin-right: 30px; text-align: center; } #box_1 img { margin: 15px 0px; } #box_2 img { margin: 15px 0px; } #bottom { width: 900px; margin: 0px auto 0px auto; text-align: center; background-color: white; -moz-border-radius: 15px; border-radius: 15px; clear:both; } /* Classes */ .clear { clear: both; }

  Read the article

< Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >